Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 593 insertions, 0 deletions

diff --git a/drivers/media/pci/cx18/cx18-dvb.c b/drivers/media/pci/cx18/cx18-dvb.c
new file mode 100644
index 0000000000..cf82360a50
--- /dev/null
+++ b/drivers/media/pci/cx18/cx18-dvb.c
@@ -0,0 +1,593 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  cx18 functions for DVB support
+ *
+ *  Copyright (c) 2008 Steven Toth <stoth@linuxtv.org>
+ *  Copyright (C) 2008  Andy Walls <awalls@md.metrocast.net>
+ */
+
+#include "cx18-version.h"
+#include "cx18-dvb.h"
+#include "cx18-io.h"
+#include "cx18-queue.h"
+#include "cx18-streams.h"
+#include "cx18-cards.h"
+#include "cx18-gpio.h"
+#include "s5h1409.h"
+#include "mxl5005s.h"
+#include "s5h1411.h"
+#include "tda18271.h"
+#include "zl10353.h"
+
+#include <linux/firmware.h>
+#include "mt352.h"
+#include "mt352_priv.h"
+#include "xc2028.h"
+
+DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr);
+
+#define FWFILE "dvb-cx18-mpc718-mt352.fw"
+
+#define CX18_REG_DMUX_NUM_PORT_0_CONTROL 0xd5a000
+#define CX18_CLOCK_ENABLE2		 0xc71024
+#define CX18_DMUX_CLK_MASK		 0x0080
+
+/*
+ * CX18_CARD_HVR_1600_ESMT
+ * CX18_CARD_HVR_1600_SAMSUNG
+ */
+
+static struct mxl5005s_config hauppauge_hvr1600_tuner = {
+	.i2c_address     = 0xC6 >> 1,
+	.if_freq         = IF_FREQ_5380000HZ,
+	.xtal_freq       = CRYSTAL_FREQ_16000000HZ,
+	.agc_mode        = MXL_SINGLE_AGC,
+	.tracking_filter = MXL_TF_C_H,
+	.rssi_enable     = MXL_RSSI_ENABLE,
+	.cap_select      = MXL_CAP_SEL_ENABLE,
+	.div_out         = MXL_DIV_OUT_4,
+	.clock_out       = MXL_CLOCK_OUT_DISABLE,
+	.output_load     = MXL5005S_IF_OUTPUT_LOAD_200_OHM,
+	.top		 = MXL5005S_TOP_25P2,
+	.mod_mode        = MXL_DIGITAL_MODE,
+	.if_mode         = MXL_ZERO_IF,
+	.qam_gain        = 0x02,
+	.AgcMasterByte   = 0x00,
+};
+
+static struct s5h1409_config hauppauge_hvr1600_config = {
+	.demod_address = 0x32 >> 1,
+	.output_mode   = S5H1409_SERIAL_OUTPUT,
+	.gpio          = S5H1409_GPIO_ON,
+	.qam_if        = 44000,
+	.inversion     = S5H1409_INVERSION_OFF,
+	.status_mode   = S5H1409_DEMODLOCKING,
+	.mpeg_timing   = S5H1409_MPEGTIMING_CONTINUOUS_NONINVERTING_CLOCK,
+	.hvr1600_opt   = S5H1409_HVR1600_OPTIMIZE
+};
+
+/*
+ * CX18_CARD_HVR_1600_S5H1411
+ */
+static struct s5h1411_config hcw_s5h1411_config = {
+	.output_mode   = S5H1411_SERIAL_OUTPUT,
+	.gpio          = S5H1411_GPIO_OFF,
+	.vsb_if        = S5H1411_IF_44000,
+	.qam_if        = S5H1411_IF_4000,
+	.inversion     = S5H1411_INVERSION_ON,
+	.status_mode   = S5H1411_DEMODLOCKING,
+	.mpeg_timing   = S5H1411_MPEGTIMING_CONTINUOUS_NONINVERTING_CLOCK,
+};
+
+static struct tda18271_std_map hauppauge_tda18271_std_map = {
+	.atsc_6   = { .if_freq = 5380, .agc_mode = 3, .std = 3,
+		      .if_lvl = 6, .rfagc_top = 0x37 },
+	.qam_6    = { .if_freq = 4000, .agc_mode = 3, .std = 0,
+		      .if_lvl = 6, .rfagc_top = 0x37 },
+};
+
+static struct tda18271_config hauppauge_tda18271_config = {
+	.std_map = &hauppauge_tda18271_std_map,
+	.gate    = TDA18271_GATE_DIGITAL,
+	.output_opt = TDA18271_OUTPUT_LT_OFF,
+};
+
+/*
+ * CX18_CARD_LEADTEK_DVR3100H
+ */
+/* Information/confirmation of proper config values provided by Terry Wu */
+static struct zl10353_config leadtek_dvr3100h_demod = {
+	.demod_address         = 0x1e >> 1, /* Datasheet suggested straps */
+	.if2                   = 45600,     /* 4.560 MHz IF from the XC3028 */
+	.parallel_ts           = 1,         /* Not a serial TS */
+	.no_tuner              = 1,         /* XC3028 is not behind the gate */
+	.disable_i2c_gate_ctrl = 1,         /* Disable the I2C gate */
+};
+
+/*
+ * CX18_CARD_YUAN_MPC718
+ */
+/*
+ * Due to
+ *
+ * 1. an absence of information on how to program the MT352
+ * 2. the Linux mt352 module pushing MT352 initialization off onto us here
+ *
+ * We have to use an init sequence that *you* must extract from the Windows
+ * driver (yuanrap.sys) and which we load as a firmware.
+ *
+ * If someone can provide me with a Zarlink MT352 (Intel CE6352?) Design Manual
+ * with chip programming details, then I can remove this annoyance.
+ */
+static int yuan_mpc718_mt352_reqfw(struct cx18_stream *stream,
+				   const struct firmware **fw)
+{
+	struct cx18 *cx = stream->cx;
+	const char *fn = FWFILE;
+	int ret;
+
+	ret = request_firmware(fw, fn, &cx->pci_dev->dev);
+	if (ret)
+		CX18_ERR("Unable to open firmware file %s\n", fn);
+	else {
+		size_t sz = (*fw)->size;
+		if (sz < 2 || sz > 64 || (sz % 2) != 0) {
+			CX18_ERR("Firmware %s has a bad size: %lu bytes\n",
+				 fn, (unsigned long) sz);
+			ret = -EILSEQ;
+			release_firmware(*fw);
+			*fw = NULL;
+		}
+	}
+
+	if (ret) {
+		CX18_ERR("The MPC718 board variant with the MT352 DVB-T demodulator will not work without it\n");
+		CX18_ERR("Run 'linux/scripts/get_dvb_firmware mpc718' if you need the firmware\n");
+	}
+	return ret;
+}
+
+static int yuan_mpc718_mt352_init(struct dvb_frontend *fe)
+{
+	struct cx18_dvb *dvb = container_of(fe->dvb,
+					    struct cx18_dvb, dvb_adapter);
+	struct cx18_stream *stream = dvb->stream;
+	const struct firmware *fw = NULL;
+	int ret;
+	int i;
+	u8 buf[3];
+
+	ret = yuan_mpc718_mt352_reqfw(stream, &fw);
+	if (ret)
+		return ret;
+
+	/* Loop through all the register-value pairs in the firmware file */
+	for (i = 0; i < fw->size; i += 2) {
+		buf[0] = fw->data[i];
+		/* Intercept a few registers we want to set ourselves */
+		switch (buf[0]) {
+		case TRL_NOMINAL_RATE_0:
+			/* Set our custom OFDM bandwidth in the case below */
+			break;
+		case TRL_NOMINAL_RATE_1:
+			/* 6 MHz: 64/7 * 6/8 / 20.48 * 2^16 = 0x55b6.db6 */
+			/* 7 MHz: 64/7 * 7/8 / 20.48 * 2^16 = 0x6400 */
+			/* 8 MHz: 64/7 * 8/8 / 20.48 * 2^16 = 0x7249.249 */
+			buf[1] = 0x72;
+			buf[2] = 0x49;
+			mt352_write(fe, buf, 3);
+			break;
+		case INPUT_FREQ_0:
+			/* Set our custom IF in the case below */
+			break;
+		case INPUT_FREQ_1:
+			/* 4.56 MHz IF: (20.48 - 4.56)/20.48 * 2^14 = 0x31c0 */
+			buf[1] = 0x31;
+			buf[2] = 0xc0;
+			mt352_write(fe, buf, 3);
+			break;
+		default:
+			/* Pass through the register-value pair from the fw */
+			buf[1] = fw->data[i+1];
+			mt352_write(fe, buf, 2);
+			break;
+		}
+	}
+
+	buf[0] = (u8) TUNER_GO;
+	buf[1] = 0x01; /* Go */
+	mt352_write(fe, buf, 2);
+	release_firmware(fw);
+	return 0;
+}
+
+static struct mt352_config yuan_mpc718_mt352_demod = {
+	.demod_address = 0x1e >> 1,
+	.adc_clock     = 20480,     /* 20.480 MHz */
+	.if2           =  4560,     /*  4.560 MHz */
+	.no_tuner      = 1,         /* XC3028 is not behind the gate */
+	.demod_init    = yuan_mpc718_mt352_init,
+};
+
+static struct zl10353_config yuan_mpc718_zl10353_demod = {
+	.demod_address         = 0x1e >> 1, /* Datasheet suggested straps */
+	.if2                   = 45600,     /* 4.560 MHz IF from the XC3028 */
+	.parallel_ts           = 1,         /* Not a serial TS */
+	.no_tuner              = 1,         /* XC3028 is not behind the gate */
+	.disable_i2c_gate_ctrl = 1,         /* Disable the I2C gate */
+};
+
+static struct zl10353_config gotview_dvd3_zl10353_demod = {
+	.demod_address         = 0x1e >> 1, /* Datasheet suggested straps */
+	.if2                   = 45600,     /* 4.560 MHz IF from the XC3028 */
+	.parallel_ts           = 1,         /* Not a serial TS */
+	.no_tuner              = 1,         /* XC3028 is not behind the gate */
+	.disable_i2c_gate_ctrl = 1,         /* Disable the I2C gate */
+};
+
+static int dvb_register(struct cx18_stream *stream);
+
+/* Kernel DVB framework calls this when the feed needs to start.
+ * The CX18 framework should enable the transport DMA handling
+ * and queue processing.
+ */
+static int cx18_dvb_start_feed(struct dvb_demux_feed *feed)
+{
+	struct dvb_demux *demux = feed->demux;
+	struct cx18_stream *stream = demux->priv;
+	struct cx18 *cx;
+	int ret;
+	u32 v;
+
+	if (!stream)
+		return -EINVAL;
+
+	cx = stream->cx;
+	CX18_DEBUG_INFO("Start feed: pid = 0x%x index = %d\n",
+			feed->pid, feed->index);
+
+	mutex_lock(&cx->serialize_lock);
+	ret = cx18_init_on_first_open(cx);
+	mutex_unlock(&cx->serialize_lock);
+	if (ret) {
+		CX18_ERR("Failed to initialize firmware starting DVB feed\n");
+		return ret;
+	}
+	ret = -EINVAL;
+
+	switch (cx->card->type) {
+	case CX18_CARD_HVR_1600_ESMT:
+	case CX18_CARD_HVR_1600_SAMSUNG:
+	case CX18_CARD_HVR_1600_S5H1411:
+		v = cx18_read_reg(cx, CX18_REG_DMUX_NUM_PORT_0_CONTROL);
+		v |= 0x00400000; /* Serial Mode */
+		v |= 0x00002000; /* Data Length - Byte */
+		v |= 0x00010000; /* Error - Polarity */
+		v |= 0x00020000; /* Error - Passthru */
+		v |= 0x000c0000; /* Error - Ignore */
+		cx18_write_reg(cx, v, CX18_REG_DMUX_NUM_PORT_0_CONTROL);
+		break;
+
+	case CX18_CARD_LEADTEK_DVR3100H:
+	case CX18_CARD_YUAN_MPC718:
+	case CX18_CARD_GOTVIEW_PCI_DVD3:
+	default:
+		/* Assumption - Parallel transport - Signalling
+		 * undefined or default.
+		 */
+		break;
+	}
+
+	if (!demux->dmx.frontend)
+		return -EINVAL;
+
+	mutex_lock(&stream->dvb->feedlock);
+	if (stream->dvb->feeding++ == 0) {
+		CX18_DEBUG_INFO("Starting Transport DMA\n");
+		mutex_lock(&cx->serialize_lock);
+		set_bit(CX18_F_S_STREAMING, &stream->s_flags);
+		ret = cx18_start_v4l2_encode_stream(stream);
+		if (ret < 0) {
+			CX18_DEBUG_INFO("Failed to start Transport DMA\n");
+			stream->dvb->feeding--;
+			if (stream->dvb->feeding == 0)
+				clear_bit(CX18_F_S_STREAMING, &stream->s_flags);
+		}
+		mutex_unlock(&cx->serialize_lock);
+	} else
+		ret = 0;
+	mutex_unlock(&stream->dvb->feedlock);
+
+	return ret;
+}
+
+/* Kernel DVB framework calls this when the feed needs to stop. */
+static int cx18_dvb_stop_feed(struct dvb_demux_feed *feed)
+{
+	struct dvb_demux *demux = feed->demux;
+	struct cx18_stream *stream = demux->priv;
+	struct cx18 *cx;
+	int ret = -EINVAL;
+
+	if (stream) {
+		cx = stream->cx;
+		CX18_DEBUG_INFO("Stop feed: pid = 0x%x index = %d\n",
+				feed->pid, feed->index);
+
+		mutex_lock(&stream->dvb->feedlock);
+		if (--stream->dvb->feeding == 0) {
+			CX18_DEBUG_INFO("Stopping Transport DMA\n");
+			mutex_lock(&cx->serialize_lock);
+			ret = cx18_stop_v4l2_encode_stream(stream, 0);
+			mutex_unlock(&cx->serialize_lock);
+		} else
+			ret = 0;
+		mutex_unlock(&stream->dvb->feedlock);
+	}
+
+	return ret;
+}
+
+int cx18_dvb_register(struct cx18_stream *stream)
+{
+	struct cx18 *cx = stream->cx;
+	struct cx18_dvb *dvb = stream->dvb;
+	struct dvb_adapter *dvb_adapter;
+	struct dvb_demux *dvbdemux;
+	struct dmx_demux *dmx;
+	int ret;
+
+	if (!dvb)
+		return -EINVAL;
+
+	dvb->enabled = 0;
+	dvb->stream = stream;
+
+	ret = dvb_register_adapter(&dvb->dvb_adapter,
+			CX18_DRIVER_NAME,
+			THIS_MODULE, &cx->pci_dev->dev, adapter_nr);
+	if (ret < 0)
+		goto err_out;
+
+	dvb_adapter = &dvb->dvb_adapter;
+
+	dvbdemux = &dvb->demux;
+
+	dvbdemux->priv = (void *)stream;
+
+	dvbdemux->filternum = 256;
+	dvbdemux->feednum = 256;
+	dvbdemux->start_feed = cx18_dvb_start_feed;
+	dvbdemux->stop_feed = cx18_dvb_stop_feed;
+	dvbdemux->dmx.capabilities = (DMX_TS_FILTERING |
+		DMX_SECTION_FILTERING | DMX_MEMORY_BASED_FILTERING);
+	ret = dvb_dmx_init(dvbdemux);
+	if (ret < 0)
+		goto err_dvb_unregister_adapter;
+
+	dmx = &dvbdemux->dmx;
+
+	dvb->hw_frontend.source = DMX_FRONTEND_0;
+	dvb->mem_frontend.source = DMX_MEMORY_FE;
+	dvb->dmxdev.filternum = 256;
+	dvb->dmxdev.demux = dmx;
+
+	ret = dvb_dmxdev_init(&dvb->dmxdev, dvb_adapter);
+	if (ret < 0)
+		goto err_dvb_dmx_release;
+
+	ret = dmx->add_frontend(dmx, &dvb->hw_frontend);
+	if (ret < 0)
+		goto err_dvb_dmxdev_release;
+
+	ret = dmx->add_frontend(dmx, &dvb->mem_frontend);
+	if (ret < 0)
+		goto err_remove_hw_frontend;
+
+	ret = dmx->connect_frontend(dmx, &dvb->hw_frontend);
+	if (ret < 0)
+		goto err_remove_mem_frontend;
+
+	ret = dvb_register(stream);
+	if (ret < 0)
+		goto err_disconnect_frontend;
+
+	dvb_net_init(dvb_adapter, &dvb->dvbnet, dmx);
+
+	CX18_INFO("DVB Frontend registered\n");
+	CX18_INFO("Registered DVB adapter%d for %s (%d x %d.%02d kB)\n",
+		  stream->dvb->dvb_adapter.num, stream->name,
+		  stream->buffers, stream->buf_size/1024,
+		  (stream->buf_size * 100 / 1024) % 100);
+
+	mutex_init(&dvb->feedlock);
+	dvb->enabled = 1;
+	return ret;
+
+err_disconnect_frontend:
+	dmx->disconnect_frontend(dmx);
+err_remove_mem_frontend:
+	dmx->remove_frontend(dmx, &dvb->mem_frontend);
+err_remove_hw_frontend:
+	dmx->remove_frontend(dmx, &dvb->hw_frontend);
+err_dvb_dmxdev_release:
+	dvb_dmxdev_release(&dvb->dmxdev);
+err_dvb_dmx_release:
+	dvb_dmx_release(dvbdemux);
+err_dvb_unregister_adapter:
+	dvb_unregister_adapter(dvb_adapter);
+err_out:
+	return ret;
+}
+
+void cx18_dvb_unregister(struct cx18_stream *stream)
+{
+	struct cx18 *cx = stream->cx;
+	struct cx18_dvb *dvb = stream->dvb;
+	struct dvb_adapter *dvb_adapter;
+	struct dvb_demux *dvbdemux;
+	struct dmx_demux *dmx;
+
+	CX18_INFO("unregister DVB\n");
+
+	if (dvb == NULL || !dvb->enabled)
+		return;
+
+	dvb_adapter = &dvb->dvb_adapter;
+	dvbdemux = &dvb->demux;
+	dmx = &dvbdemux->dmx;
+
+	dmx->close(dmx);
+	dvb_net_release(&dvb->dvbnet);
+	dmx->remove_frontend(dmx, &dvb->mem_frontend);
+	dmx->remove_frontend(dmx, &dvb->hw_frontend);
+	dvb_dmxdev_release(&dvb->dmxdev);
+	dvb_dmx_release(dvbdemux);
+	dvb_unregister_frontend(dvb->fe);
+	dvb_frontend_detach(dvb->fe);
+	dvb_unregister_adapter(dvb_adapter);
+}
+
+/* All the DVB attach calls go here, this function gets modified
+ * for each new card. cx18_dvb_start_feed() will also need changes.
+ */
+static int dvb_register(struct cx18_stream *stream)
+{
+	struct cx18_dvb *dvb = stream->dvb;
+	struct cx18 *cx = stream->cx;
+	int ret = 0;
+
+	switch (cx->card->type) {
+	case CX18_CARD_HVR_1600_ESMT:
+	case CX18_CARD_HVR_1600_SAMSUNG:
+		dvb->fe = dvb_attach(s5h1409_attach,
+			&hauppauge_hvr1600_config,
+			&cx->i2c_adap[0]);
+		if (dvb->fe != NULL) {
+			dvb_attach(mxl5005s_attach, dvb->fe,
+				&cx->i2c_adap[0],
+				&hauppauge_hvr1600_tuner);
+			ret = 0;
+		}
+		break;
+	case CX18_CARD_HVR_1600_S5H1411:
+		dvb->fe = dvb_attach(s5h1411_attach,
+				     &hcw_s5h1411_config,
+				     &cx->i2c_adap[0]);
+		if (dvb->fe != NULL)
+			dvb_attach(tda18271_attach, dvb->fe,
+				   0x60, &cx->i2c_adap[0],
+				   &hauppauge_tda18271_config);
+		break;
+	case CX18_CARD_LEADTEK_DVR3100H:
+		dvb->fe = dvb_attach(zl10353_attach,
+				     &leadtek_dvr3100h_demod,
+				     &cx->i2c_adap[1]);
+		if (dvb->fe != NULL) {
+			struct dvb_frontend *fe;
+			struct xc2028_config cfg = {
+				.i2c_adap = &cx->i2c_adap[1],
+				.i2c_addr = 0xc2 >> 1,
+				.ctrl = NULL,
+			};
+			static struct xc2028_ctrl ctrl = {
+				.fname   = XC2028_DEFAULT_FIRMWARE,
+				.max_len = 64,
+				.demod   = XC3028_FE_ZARLINK456,
+				.type    = XC2028_AUTO,
+			};
+
+			fe = dvb_attach(xc2028_attach, dvb->fe, &cfg);
+			if (fe != NULL && fe->ops.tuner_ops.set_config != NULL)
+				fe->ops.tuner_ops.set_config(fe, &ctrl);
+		}
+		break;
+	case CX18_CARD_YUAN_MPC718:
+		/*
+		 * TODO
+		 * Apparently, these cards also could instead have a
+		 * DiBcom demod supported by one of the db7000 drivers
+		 */
+		dvb->fe = dvb_attach(mt352_attach,
+				     &yuan_mpc718_mt352_demod,
+				     &cx->i2c_adap[1]);
+		if (dvb->fe == NULL)
+			dvb->fe = dvb_attach(zl10353_attach,
+					     &yuan_mpc718_zl10353_demod,
+					     &cx->i2c_adap[1]);
+		if (dvb->fe != NULL) {
+			struct dvb_frontend *fe;
+			struct xc2028_config cfg = {
+				.i2c_adap = &cx->i2c_adap[1],
+				.i2c_addr = 0xc2 >> 1,
+				.ctrl = NULL,
+			};
+			static struct xc2028_ctrl ctrl = {
+				.fname   = XC2028_DEFAULT_FIRMWARE,
+				.max_len = 64,
+				.demod   = XC3028_FE_ZARLINK456,
+				.type    = XC2028_AUTO,
+			};
+
+			fe = dvb_attach(xc2028_attach, dvb->fe, &cfg);
+			if (fe != NULL && fe->ops.tuner_ops.set_config != NULL)
+				fe->ops.tuner_ops.set_config(fe, &ctrl);
+		}
+		break;
+	case CX18_CARD_GOTVIEW_PCI_DVD3:
+			dvb->fe = dvb_attach(zl10353_attach,
+					     &gotview_dvd3_zl10353_demod,
+					     &cx->i2c_adap[1]);
+		if (dvb->fe != NULL) {
+			struct dvb_frontend *fe;
+			struct xc2028_config cfg = {
+				.i2c_adap = &cx->i2c_adap[1],
+				.i2c_addr = 0xc2 >> 1,
+				.ctrl = NULL,
+			};
+			static struct xc2028_ctrl ctrl = {
+				.fname   = XC2028_DEFAULT_FIRMWARE,
+				.max_len = 64,
+				.demod   = XC3028_FE_ZARLINK456,
+				.type    = XC2028_AUTO,
+			};
+
+			fe = dvb_attach(xc2028_attach, dvb->fe, &cfg);
+			if (fe != NULL && fe->ops.tuner_ops.set_config != NULL)
+				fe->ops.tuner_ops.set_config(fe, &ctrl);
+		}
+		break;
+	default:
+		/* No Digital Tv Support */
+		break;
+	}
+
+	if (dvb->fe == NULL) {
+		CX18_ERR("frontend initialization failed\n");
+		return -1;
+	}
+
+	dvb->fe->callback = cx18_reset_tuner_gpio;
+
+	ret = dvb_register_frontend(&dvb->dvb_adapter, dvb->fe);
+	if (ret < 0) {
+		if (dvb->fe->ops.release)
+			dvb->fe->ops.release(dvb->fe);
+		return ret;
+	}
+
+	/*
+	 * The firmware seems to enable the TS DMUX clock
+	 * under various circumstances.  However, since we know we
+	 * might use it, let's just turn it on ourselves here.
+	 */
+	cx18_write_reg_expect(cx,
+			      (CX18_DMUX_CLK_MASK << 16) | CX18_DMUX_CLK_MASK,
+			      CX18_CLOCK_ENABLE2,
+			      CX18_DMUX_CLK_MASK,
+			      (CX18_DMUX_CLK_MASK << 16) | CX18_DMUX_CLK_MASK);
+
+	return ret;
+}
+
+MODULE_FIRMWARE(FWFILE);