Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 428 insertions, 0 deletions

diff --git a/drivers/media/usb/gspca/sq905.c b/drivers/media/usb/gspca/sq905.c
new file mode 100644
index 0000000000..32504ebcfd
--- /dev/null
+++ b/drivers/media/usb/gspca/sq905.c
@@ -0,0 +1,428 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * SQ905 subdriver
+ *
+ * Copyright (C) 2008, 2009 Adam Baker and Theodore Kilgore
+ */
+
+/*
+ * History and Acknowledgments
+ *
+ * The original Linux driver for SQ905 based cameras was written by
+ * Marcell Lengyel and further developed by many other contributors
+ * and is available from http://sourceforge.net/projects/sqcam/
+ *
+ * This driver takes advantage of the reverse engineering work done for
+ * that driver and for libgphoto2 but shares no code with them.
+ *
+ * This driver has used as a base the finepix driver and other gspca
+ * based drivers and may still contain code fragments taken from those
+ * drivers.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#define MODULE_NAME "sq905"
+
+#include <linux/workqueue.h>
+#include <linux/slab.h>
+#include "gspca.h"
+
+MODULE_AUTHOR("Adam Baker <linux@baker-net.org.uk>, Theodore Kilgore <kilgota@auburn.edu>");
+MODULE_DESCRIPTION("GSPCA/SQ905 USB Camera Driver");
+MODULE_LICENSE("GPL");
+
+/* Default timeouts, in ms */
+#define SQ905_CMD_TIMEOUT 500
+#define SQ905_DATA_TIMEOUT 1000
+
+/* Maximum transfer size to use. */
+#define SQ905_MAX_TRANSFER 0x8000
+#define FRAME_HEADER_LEN 64
+
+/* The known modes, or registers. These go in the "value" slot. */
+
+/* 00 is "none" obviously */
+
+#define SQ905_BULK_READ	0x03	/* precedes any bulk read */
+#define SQ905_COMMAND	0x06	/* precedes the command codes below */
+#define SQ905_PING	0x07	/* when reading an "idling" command */
+#define SQ905_READ_DONE 0xc0    /* ack bulk read completed */
+
+/* Any non-zero value in the bottom 2 bits of the 2nd byte of
+ * the ID appears to indicate the camera can do 640*480. If the
+ * LSB of that byte is set the image is just upside down, otherwise
+ * it is rotated 180 degrees. */
+#define SQ905_HIRES_MASK	0x00000300
+#define SQ905_ORIENTATION_MASK	0x00000100
+
+/* Some command codes. These go in the "index" slot. */
+
+#define SQ905_ID      0xf0	/* asks for model string */
+#define SQ905_CONFIG  0x20	/* gets photo alloc. table, not used here */
+#define SQ905_DATA    0x30	/* accesses photo data, not used here */
+#define SQ905_CLEAR   0xa0	/* clear everything */
+#define SQ905_CAPTURE_LOW  0x60	/* Starts capture at 160x120 */
+#define SQ905_CAPTURE_MED  0x61	/* Starts capture at 320x240 */
+#define SQ905_CAPTURE_HIGH 0x62	/* Starts capture at 640x480 (some cams only) */
+/* note that the capture command also controls the output dimensions */
+
+/* Structure to hold all of our device specific stuff */
+struct sd {
+	struct gspca_dev gspca_dev;	/* !! must be the first item */
+
+	/*
+	 * Driver stuff
+	 */
+	struct work_struct work_struct;
+	struct workqueue_struct *work_thread;
+};
+
+static struct v4l2_pix_format sq905_mode[] = {
+	{ 160, 120, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE,
+		.bytesperline = 160,
+		.sizeimage = 160 * 120,
+		.colorspace = V4L2_COLORSPACE_SRGB,
+		.priv = 0},
+	{ 320, 240, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE,
+		.bytesperline = 320,
+		.sizeimage = 320 * 240,
+		.colorspace = V4L2_COLORSPACE_SRGB,
+		.priv = 0},
+	{ 640, 480, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE,
+		.bytesperline = 640,
+		.sizeimage = 640 * 480,
+		.colorspace = V4L2_COLORSPACE_SRGB,
+		.priv = 0}
+};
+
+/*
+ * Send a command to the camera.
+ */
+static int sq905_command(struct gspca_dev *gspca_dev, u16 index)
+{
+	int ret;
+
+	gspca_dev->usb_buf[0] = '\0';
+	ret = usb_control_msg(gspca_dev->dev,
+			      usb_sndctrlpipe(gspca_dev->dev, 0),
+			      USB_REQ_SYNCH_FRAME,                /* request */
+			      USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+			      SQ905_COMMAND, index, gspca_dev->usb_buf, 1,
+			      SQ905_CMD_TIMEOUT);
+	if (ret < 0) {
+		pr_err("%s: usb_control_msg failed (%d)\n", __func__, ret);
+		return ret;
+	}
+
+	ret = usb_control_msg(gspca_dev->dev,
+			      usb_rcvctrlpipe(gspca_dev->dev, 0),
+			      USB_REQ_SYNCH_FRAME,                /* request */
+			      USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+			      SQ905_PING, 0, gspca_dev->usb_buf, 1,
+			      SQ905_CMD_TIMEOUT);
+	if (ret < 0) {
+		pr_err("%s: usb_control_msg failed 2 (%d)\n", __func__, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * Acknowledge the end of a frame - see warning on sq905_command.
+ */
+static int sq905_ack_frame(struct gspca_dev *gspca_dev)
+{
+	int ret;
+
+	gspca_dev->usb_buf[0] = '\0';
+	ret = usb_control_msg(gspca_dev->dev,
+			      usb_sndctrlpipe(gspca_dev->dev, 0),
+			      USB_REQ_SYNCH_FRAME,                /* request */
+			      USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+			      SQ905_READ_DONE, 0, gspca_dev->usb_buf, 1,
+			      SQ905_CMD_TIMEOUT);
+	if (ret < 0) {
+		pr_err("%s: usb_control_msg failed (%d)\n", __func__, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ *  request and read a block of data - see warning on sq905_command.
+ */
+static int
+sq905_read_data(struct gspca_dev *gspca_dev, u8 *data, int size, int need_lock)
+{
+	int ret;
+	int act_len = 0;
+
+	gspca_dev->usb_buf[0] = '\0';
+	if (need_lock)
+		mutex_lock(&gspca_dev->usb_lock);
+	ret = usb_control_msg(gspca_dev->dev,
+			      usb_sndctrlpipe(gspca_dev->dev, 0),
+			      USB_REQ_SYNCH_FRAME,                /* request */
+			      USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+			      SQ905_BULK_READ, size, gspca_dev->usb_buf,
+			      1, SQ905_CMD_TIMEOUT);
+	if (need_lock)
+		mutex_unlock(&gspca_dev->usb_lock);
+	if (ret < 0) {
+		pr_err("%s: usb_control_msg failed (%d)\n", __func__, ret);
+		return ret;
+	}
+	ret = usb_bulk_msg(gspca_dev->dev,
+			   usb_rcvbulkpipe(gspca_dev->dev, 0x81),
+			   data, size, &act_len, SQ905_DATA_TIMEOUT);
+
+	/* successful, it returns 0, otherwise  negative */
+	if (ret < 0 || act_len != size) {
+		pr_err("bulk read fail (%d) len %d/%d\n", ret, act_len, size);
+		return -EIO;
+	}
+	return 0;
+}
+
+/*
+ * This function is called as a workqueue function and runs whenever the camera
+ * is streaming data. Because it is a workqueue function it is allowed to sleep
+ * so we can use synchronous USB calls. To avoid possible collisions with other
+ * threads attempting to use gspca_dev->usb_buf we take the usb_lock when
+ * performing USB operations using it. In practice we don't really need this
+ * as the camera doesn't provide any controls.
+ */
+static void sq905_dostream(struct work_struct *work)
+{
+	struct sd *dev = container_of(work, struct sd, work_struct);
+	struct gspca_dev *gspca_dev = &dev->gspca_dev;
+	int bytes_left; /* bytes remaining in current frame. */
+	int data_len;   /* size to use for the next read. */
+	int header_read; /* true if we have already read the frame header. */
+	int packet_type;
+	int frame_sz;
+	int ret;
+	u8 *data;
+	u8 *buffer;
+
+	buffer = kmalloc(SQ905_MAX_TRANSFER, GFP_KERNEL);
+	if (!buffer) {
+		pr_err("Couldn't allocate USB buffer\n");
+		goto quit_stream;
+	}
+
+	frame_sz = gspca_dev->cam.cam_mode[gspca_dev->curr_mode].sizeimage
+			+ FRAME_HEADER_LEN;
+
+	while (gspca_dev->present && gspca_dev->streaming) {
+#ifdef CONFIG_PM
+		if (gspca_dev->frozen)
+			break;
+#endif
+		/* request some data and then read it until we have
+		 * a complete frame. */
+		bytes_left = frame_sz;
+		header_read = 0;
+
+		/* Note we do not check for gspca_dev->streaming here, as
+		   we must finish reading an entire frame, otherwise the
+		   next time we stream we start reading in the middle of a
+		   frame. */
+		while (bytes_left > 0 && gspca_dev->present) {
+			data_len = bytes_left > SQ905_MAX_TRANSFER ?
+				SQ905_MAX_TRANSFER : bytes_left;
+			ret = sq905_read_data(gspca_dev, buffer, data_len, 1);
+			if (ret < 0)
+				goto quit_stream;
+			gspca_dbg(gspca_dev, D_PACK,
+				  "Got %d bytes out of %d for frame\n",
+				  data_len, bytes_left);
+			bytes_left -= data_len;
+			data = buffer;
+			if (!header_read) {
+				packet_type = FIRST_PACKET;
+				/* The first 64 bytes of each frame are
+				 * a header full of FF 00 bytes */
+				data += FRAME_HEADER_LEN;
+				data_len -= FRAME_HEADER_LEN;
+				header_read = 1;
+			} else if (bytes_left == 0) {
+				packet_type = LAST_PACKET;
+			} else {
+				packet_type = INTER_PACKET;
+			}
+			gspca_frame_add(gspca_dev, packet_type,
+					data, data_len);
+			/* If entire frame fits in one packet we still
+			   need to add a LAST_PACKET */
+			if (packet_type == FIRST_PACKET &&
+			    bytes_left == 0)
+				gspca_frame_add(gspca_dev, LAST_PACKET,
+						NULL, 0);
+		}
+		if (gspca_dev->present) {
+			/* acknowledge the frame */
+			mutex_lock(&gspca_dev->usb_lock);
+			ret = sq905_ack_frame(gspca_dev);
+			mutex_unlock(&gspca_dev->usb_lock);
+			if (ret < 0)
+				goto quit_stream;
+		}
+	}
+quit_stream:
+	if (gspca_dev->present) {
+		mutex_lock(&gspca_dev->usb_lock);
+		sq905_command(gspca_dev, SQ905_CLEAR);
+		mutex_unlock(&gspca_dev->usb_lock);
+	}
+	kfree(buffer);
+}
+
+/* This function is called at probe time just before sd_init */
+static int sd_config(struct gspca_dev *gspca_dev,
+		const struct usb_device_id *id)
+{
+	struct cam *cam = &gspca_dev->cam;
+	struct sd *dev = (struct sd *) gspca_dev;
+
+	/* We don't use the buffer gspca allocates so make it small. */
+	cam->bulk = 1;
+	cam->bulk_size = 64;
+
+	INIT_WORK(&dev->work_struct, sq905_dostream);
+
+	return 0;
+}
+
+/* called on streamoff with alt==0 and on disconnect */
+/* the usb_lock is held at entry - restore on exit */
+static void sd_stop0(struct gspca_dev *gspca_dev)
+{
+	struct sd *dev = (struct sd *) gspca_dev;
+
+	/* wait for the work queue to terminate */
+	mutex_unlock(&gspca_dev->usb_lock);
+	/* This waits for sq905_dostream to finish */
+	destroy_workqueue(dev->work_thread);
+	dev->work_thread = NULL;
+	mutex_lock(&gspca_dev->usb_lock);
+}
+
+/* this function is called at probe and resume time */
+static int sd_init(struct gspca_dev *gspca_dev)
+{
+	u32 ident;
+	int ret;
+
+	/* connect to the camera and read
+	 * the model ID and process that and put it away.
+	 */
+	ret = sq905_command(gspca_dev, SQ905_CLEAR);
+	if (ret < 0)
+		return ret;
+	ret = sq905_command(gspca_dev, SQ905_ID);
+	if (ret < 0)
+		return ret;
+	ret = sq905_read_data(gspca_dev, gspca_dev->usb_buf, 4, 0);
+	if (ret < 0)
+		return ret;
+	/* usb_buf is allocated with kmalloc so is aligned.
+	 * Camera model number is the right way round if we assume this
+	 * reverse engineered ID is supposed to be big endian. */
+	ident = be32_to_cpup((__be32 *)gspca_dev->usb_buf);
+	ret = sq905_command(gspca_dev, SQ905_CLEAR);
+	if (ret < 0)
+		return ret;
+	gspca_dbg(gspca_dev, D_CONF, "SQ905 camera ID %08x detected\n", ident);
+	gspca_dev->cam.cam_mode = sq905_mode;
+	gspca_dev->cam.nmodes = ARRAY_SIZE(sq905_mode);
+	if (!(ident & SQ905_HIRES_MASK))
+		gspca_dev->cam.nmodes--;
+
+	if (ident & SQ905_ORIENTATION_MASK)
+		gspca_dev->cam.input_flags = V4L2_IN_ST_VFLIP;
+	else
+		gspca_dev->cam.input_flags = V4L2_IN_ST_VFLIP |
+					     V4L2_IN_ST_HFLIP;
+	return 0;
+}
+
+/* Set up for getting frames. */
+static int sd_start(struct gspca_dev *gspca_dev)
+{
+	struct sd *dev = (struct sd *) gspca_dev;
+	int ret;
+
+	/* "Open the shutter" and set size, to start capture */
+	switch (gspca_dev->curr_mode) {
+	default:
+/*	case 2: */
+		gspca_dbg(gspca_dev, D_STREAM, "Start streaming at high resolution\n");
+		ret = sq905_command(&dev->gspca_dev, SQ905_CAPTURE_HIGH);
+		break;
+	case 1:
+		gspca_dbg(gspca_dev, D_STREAM, "Start streaming at medium resolution\n");
+		ret = sq905_command(&dev->gspca_dev, SQ905_CAPTURE_MED);
+		break;
+	case 0:
+		gspca_dbg(gspca_dev, D_STREAM, "Start streaming at low resolution\n");
+		ret = sq905_command(&dev->gspca_dev, SQ905_CAPTURE_LOW);
+	}
+
+	if (ret < 0) {
+		gspca_err(gspca_dev, "Start streaming command failed\n");
+		return ret;
+	}
+	/* Start the workqueue function to do the streaming */
+	dev->work_thread = create_singlethread_workqueue(MODULE_NAME);
+	if (!dev->work_thread)
+		return -ENOMEM;
+
+	queue_work(dev->work_thread, &dev->work_struct);
+
+	return 0;
+}
+
+/* Table of supported USB devices */
+static const struct usb_device_id device_table[] = {
+	{USB_DEVICE(0x2770, 0x9120)},
+	{}
+};
+
+MODULE_DEVICE_TABLE(usb, device_table);
+
+/* sub-driver description */
+static const struct sd_desc sd_desc = {
+	.name   = MODULE_NAME,
+	.config = sd_config,
+	.init   = sd_init,
+	.start  = sd_start,
+	.stop0  = sd_stop0,
+};
+
+/* -- device connect -- */
+static int sd_probe(struct usb_interface *intf,
+		const struct usb_device_id *id)
+{
+	return gspca_dev_probe(intf, id,
+			&sd_desc,
+			sizeof(struct sd),
+			THIS_MODULE);
+}
+
+static struct usb_driver sd_driver = {
+	.name       = MODULE_NAME,
+	.id_table   = device_table,
+	.probe      = sd_probe,
+	.disconnect = gspca_disconnect,
+#ifdef CONFIG_PM
+	.suspend = gspca_suspend,
+	.resume  = gspca_resume,
+	.reset_resume = gspca_resume,
+#endif
+};
+
+module_usb_driver(sd_driver);