Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 1512 insertions, 0 deletions

diff --git a/drivers/mtd/nand/raw/arasan-nand-controller.c b/drivers/mtd/nand/raw/arasan-nand-controller.c
new file mode 100644
index 0000000000..a492051c46
--- /dev/null
+++ b/drivers/mtd/nand/raw/arasan-nand-controller.c
@@ -0,0 +1,1512 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Arasan NAND Flash Controller Driver
+ *
+ * Copyright (C) 2014 - 2020 Xilinx, Inc.
+ * Author:
+ *   Miquel Raynal <miquel.raynal@bootlin.com>
+ * Original work (fully rewritten):
+ *   Punnaiah Choudary Kalluri <punnaia@xilinx.com>
+ *   Naga Sureshkumar Relli <nagasure@xilinx.com>
+ */
+
+#include <linux/bch.h>
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/rawnand.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define PKT_REG				0x00
+#define   PKT_SIZE(x)			FIELD_PREP(GENMASK(10, 0), (x))
+#define   PKT_STEPS(x)			FIELD_PREP(GENMASK(23, 12), (x))
+
+#define MEM_ADDR1_REG			0x04
+
+#define MEM_ADDR2_REG			0x08
+#define   ADDR2_STRENGTH(x)		FIELD_PREP(GENMASK(27, 25), (x))
+#define   ADDR2_CS(x)			FIELD_PREP(GENMASK(31, 30), (x))
+
+#define CMD_REG				0x0C
+#define   CMD_1(x)			FIELD_PREP(GENMASK(7, 0), (x))
+#define   CMD_2(x)			FIELD_PREP(GENMASK(15, 8), (x))
+#define   CMD_PAGE_SIZE(x)		FIELD_PREP(GENMASK(25, 23), (x))
+#define   CMD_DMA_ENABLE		BIT(27)
+#define   CMD_NADDRS(x)			FIELD_PREP(GENMASK(30, 28), (x))
+#define   CMD_ECC_ENABLE		BIT(31)
+
+#define PROG_REG			0x10
+#define   PROG_PGRD			BIT(0)
+#define   PROG_ERASE			BIT(2)
+#define   PROG_STATUS			BIT(3)
+#define   PROG_PGPROG			BIT(4)
+#define   PROG_RDID			BIT(6)
+#define   PROG_RDPARAM			BIT(7)
+#define   PROG_RST			BIT(8)
+#define   PROG_GET_FEATURE		BIT(9)
+#define   PROG_SET_FEATURE		BIT(10)
+#define   PROG_CHG_RD_COL_ENH		BIT(14)
+
+#define INTR_STS_EN_REG			0x14
+#define INTR_SIG_EN_REG			0x18
+#define INTR_STS_REG			0x1C
+#define   WRITE_READY			BIT(0)
+#define   READ_READY			BIT(1)
+#define   XFER_COMPLETE			BIT(2)
+#define   DMA_BOUNDARY			BIT(6)
+#define   EVENT_MASK			GENMASK(7, 0)
+
+#define READY_STS_REG			0x20
+
+#define DMA_ADDR0_REG			0x50
+#define DMA_ADDR1_REG			0x24
+
+#define FLASH_STS_REG			0x28
+
+#define TIMING_REG			0x2C
+#define   TCCS_TIME_500NS		0
+#define   TCCS_TIME_300NS		3
+#define   TCCS_TIME_200NS		2
+#define   TCCS_TIME_100NS		1
+#define   FAST_TCAD			BIT(2)
+#define   DQS_BUFF_SEL_IN(x)		FIELD_PREP(GENMASK(6, 3), (x))
+#define   DQS_BUFF_SEL_OUT(x)		FIELD_PREP(GENMASK(18, 15), (x))
+
+#define DATA_PORT_REG			0x30
+
+#define ECC_CONF_REG			0x34
+#define   ECC_CONF_COL(x)		FIELD_PREP(GENMASK(15, 0), (x))
+#define   ECC_CONF_LEN(x)		FIELD_PREP(GENMASK(26, 16), (x))
+#define   ECC_CONF_BCH_EN		BIT(27)
+
+#define ECC_ERR_CNT_REG			0x38
+#define   GET_PKT_ERR_CNT(x)		FIELD_GET(GENMASK(7, 0), (x))
+#define   GET_PAGE_ERR_CNT(x)		FIELD_GET(GENMASK(16, 8), (x))
+
+#define ECC_SP_REG			0x3C
+#define   ECC_SP_CMD1(x)		FIELD_PREP(GENMASK(7, 0), (x))
+#define   ECC_SP_CMD2(x)		FIELD_PREP(GENMASK(15, 8), (x))
+#define   ECC_SP_ADDRS(x)		FIELD_PREP(GENMASK(30, 28), (x))
+
+#define ECC_1ERR_CNT_REG		0x40
+#define ECC_2ERR_CNT_REG		0x44
+
+#define DATA_INTERFACE_REG		0x6C
+#define   DIFACE_SDR_MODE(x)		FIELD_PREP(GENMASK(2, 0), (x))
+#define   DIFACE_DDR_MODE(x)		FIELD_PREP(GENMASK(5, 3), (x))
+#define   DIFACE_SDR			0
+#define   DIFACE_NVDDR			BIT(9)
+
+#define ANFC_MAX_CS			2
+#define ANFC_DFLT_TIMEOUT_US		1000000
+#define ANFC_MAX_CHUNK_SIZE		SZ_1M
+#define ANFC_MAX_PARAM_SIZE		SZ_4K
+#define ANFC_MAX_STEPS			SZ_2K
+#define ANFC_MAX_PKT_SIZE		(SZ_2K - 1)
+#define ANFC_MAX_ADDR_CYC		5U
+#define ANFC_RSVD_ECC_BYTES		21
+
+#define ANFC_XLNX_SDR_DFLT_CORE_CLK	100000000
+#define ANFC_XLNX_SDR_HS_CORE_CLK	80000000
+
+static struct gpio_desc *anfc_default_cs_array[2] = {NULL, NULL};
+
+/**
+ * struct anfc_op - Defines how to execute an operation
+ * @pkt_reg: Packet register
+ * @addr1_reg: Memory address 1 register
+ * @addr2_reg: Memory address 2 register
+ * @cmd_reg: Command register
+ * @prog_reg: Program register
+ * @steps: Number of "packets" to read/write
+ * @rdy_timeout_ms: Timeout for waits on Ready/Busy pin
+ * @len: Data transfer length
+ * @read: Data transfer direction from the controller point of view
+ * @buf: Data buffer
+ */
+struct anfc_op {
+	u32 pkt_reg;
+	u32 addr1_reg;
+	u32 addr2_reg;
+	u32 cmd_reg;
+	u32 prog_reg;
+	int steps;
+	unsigned int rdy_timeout_ms;
+	unsigned int len;
+	bool read;
+	u8 *buf;
+};
+
+/**
+ * struct anand - Defines the NAND chip related information
+ * @node:		Used to store NAND chips into a list
+ * @chip:		NAND chip information structure
+ * @rb:			Ready-busy line
+ * @page_sz:		Register value of the page_sz field to use
+ * @clk:		Expected clock frequency to use
+ * @data_iface:		Data interface timing mode to use
+ * @timings:		NV-DDR specific timings to use
+ * @ecc_conf:		Hardware ECC configuration value
+ * @strength:		Register value of the ECC strength
+ * @raddr_cycles:	Row address cycle information
+ * @caddr_cycles:	Column address cycle information
+ * @ecc_bits:		Exact number of ECC bits per syndrome
+ * @ecc_total:		Total number of ECC bytes
+ * @errloc:		Array of errors located with soft BCH
+ * @hw_ecc:		Buffer to store syndromes computed by hardware
+ * @bch:		BCH structure
+ * @cs_idx:		Array of chip-select for this device, values are indexes
+ *			of the controller structure @gpio_cs array
+ * @ncs_idx:		Size of the @cs_idx array
+ */
+struct anand {
+	struct list_head node;
+	struct nand_chip chip;
+	unsigned int rb;
+	unsigned int page_sz;
+	unsigned long clk;
+	u32 data_iface;
+	u32 timings;
+	u32 ecc_conf;
+	u32 strength;
+	u16 raddr_cycles;
+	u16 caddr_cycles;
+	unsigned int ecc_bits;
+	unsigned int ecc_total;
+	unsigned int *errloc;
+	u8 *hw_ecc;
+	struct bch_control *bch;
+	int *cs_idx;
+	int ncs_idx;
+};
+
+/**
+ * struct arasan_nfc - Defines the Arasan NAND flash controller driver instance
+ * @dev:		Pointer to the device structure
+ * @base:		Remapped register area
+ * @controller_clk:		Pointer to the system clock
+ * @bus_clk:		Pointer to the flash clock
+ * @controller:		Base controller structure
+ * @chips:		List of all NAND chips attached to the controller
+ * @cur_clk:		Current clock rate
+ * @cs_array:		CS array. Native CS are left empty, the other cells are
+ *			populated with their corresponding GPIO descriptor.
+ * @ncs:		Size of @cs_array
+ * @cur_cs:		Index in @cs_array of the currently in use CS
+ * @native_cs:		Currently selected native CS
+ * @spare_cs:		Native CS that is not wired (may be selected when a GPIO
+ *			CS is in use)
+ */
+struct arasan_nfc {
+	struct device *dev;
+	void __iomem *base;
+	struct clk *controller_clk;
+	struct clk *bus_clk;
+	struct nand_controller controller;
+	struct list_head chips;
+	unsigned int cur_clk;
+	struct gpio_desc **cs_array;
+	unsigned int ncs;
+	int cur_cs;
+	unsigned int native_cs;
+	unsigned int spare_cs;
+};
+
+static struct anand *to_anand(struct nand_chip *nand)
+{
+	return container_of(nand, struct anand, chip);
+}
+
+static struct arasan_nfc *to_anfc(struct nand_controller *ctrl)
+{
+	return container_of(ctrl, struct arasan_nfc, controller);
+}
+
+static int anfc_wait_for_event(struct arasan_nfc *nfc, unsigned int event)
+{
+	u32 val;
+	int ret;
+
+	ret = readl_relaxed_poll_timeout(nfc->base + INTR_STS_REG, val,
+					 val & event, 0,
+					 ANFC_DFLT_TIMEOUT_US);
+	if (ret) {
+		dev_err(nfc->dev, "Timeout waiting for event 0x%x\n", event);
+		return -ETIMEDOUT;
+	}
+
+	writel_relaxed(event, nfc->base + INTR_STS_REG);
+
+	return 0;
+}
+
+static int anfc_wait_for_rb(struct arasan_nfc *nfc, struct nand_chip *chip,
+			    unsigned int timeout_ms)
+{
+	struct anand *anand = to_anand(chip);
+	u32 val;
+	int ret;
+
+	/* There is no R/B interrupt, we must poll a register */
+	ret = readl_relaxed_poll_timeout(nfc->base + READY_STS_REG, val,
+					 val & BIT(anand->rb),
+					 1, timeout_ms * 1000);
+	if (ret) {
+		dev_err(nfc->dev, "Timeout waiting for R/B 0x%x\n",
+			readl_relaxed(nfc->base + READY_STS_REG));
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+static void anfc_trigger_op(struct arasan_nfc *nfc, struct anfc_op *nfc_op)
+{
+	writel_relaxed(nfc_op->pkt_reg, nfc->base + PKT_REG);
+	writel_relaxed(nfc_op->addr1_reg, nfc->base + MEM_ADDR1_REG);
+	writel_relaxed(nfc_op->addr2_reg, nfc->base + MEM_ADDR2_REG);
+	writel_relaxed(nfc_op->cmd_reg, nfc->base + CMD_REG);
+	writel_relaxed(nfc_op->prog_reg, nfc->base + PROG_REG);
+}
+
+static int anfc_pkt_len_config(unsigned int len, unsigned int *steps,
+			       unsigned int *pktsize)
+{
+	unsigned int nb, sz;
+
+	for (nb = 1; nb < ANFC_MAX_STEPS; nb *= 2) {
+		sz = len / nb;
+		if (sz <= ANFC_MAX_PKT_SIZE)
+			break;
+	}
+
+	if (sz * nb != len)
+		return -ENOTSUPP;
+
+	if (steps)
+		*steps = nb;
+
+	if (pktsize)
+		*pktsize = sz;
+
+	return 0;
+}
+
+static bool anfc_is_gpio_cs(struct arasan_nfc *nfc, int nfc_cs)
+{
+	return nfc_cs >= 0 && nfc->cs_array[nfc_cs];
+}
+
+static int anfc_relative_to_absolute_cs(struct anand *anand, int num)
+{
+	return anand->cs_idx[num];
+}
+
+static void anfc_assert_cs(struct arasan_nfc *nfc, unsigned int nfc_cs_idx)
+{
+	/* CS did not change: do nothing */
+	if (nfc->cur_cs == nfc_cs_idx)
+		return;
+
+	/* Deassert the previous CS if it was a GPIO */
+	if (anfc_is_gpio_cs(nfc, nfc->cur_cs))
+		gpiod_set_value_cansleep(nfc->cs_array[nfc->cur_cs], 1);
+
+	/* Assert the new one */
+	if (anfc_is_gpio_cs(nfc, nfc_cs_idx)) {
+		nfc->native_cs = nfc->spare_cs;
+		gpiod_set_value_cansleep(nfc->cs_array[nfc_cs_idx], 0);
+	} else {
+		nfc->native_cs = nfc_cs_idx;
+	}
+
+	nfc->cur_cs = nfc_cs_idx;
+}
+
+static int anfc_select_target(struct nand_chip *chip, int target)
+{
+	struct anand *anand = to_anand(chip);
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	unsigned int nfc_cs_idx = anfc_relative_to_absolute_cs(anand, target);
+	int ret;
+
+	anfc_assert_cs(nfc, nfc_cs_idx);
+
+	/* Update the controller timings and the potential ECC configuration */
+	writel_relaxed(anand->data_iface, nfc->base + DATA_INTERFACE_REG);
+	writel_relaxed(anand->timings, nfc->base + TIMING_REG);
+
+	/* Update clock frequency */
+	if (nfc->cur_clk != anand->clk) {
+		clk_disable_unprepare(nfc->bus_clk);
+		ret = clk_set_rate(nfc->bus_clk, anand->clk);
+		if (ret) {
+			dev_err(nfc->dev, "Failed to change clock rate\n");
+			return ret;
+		}
+
+		ret = clk_prepare_enable(nfc->bus_clk);
+		if (ret) {
+			dev_err(nfc->dev,
+				"Failed to re-enable the bus clock\n");
+			return ret;
+		}
+
+		nfc->cur_clk = anand->clk;
+	}
+
+	return 0;
+}
+
+/*
+ * When using the embedded hardware ECC engine, the controller is in charge of
+ * feeding the engine with, first, the ECC residue present in the data array.
+ * A typical read operation is:
+ * 1/ Assert the read operation by sending the relevant command/address cycles
+ *    but targeting the column of the first ECC bytes in the OOB area instead of
+ *    the main data directly.
+ * 2/ After having read the relevant number of ECC bytes, the controller uses
+ *    the RNDOUT/RNDSTART commands which are set into the "ECC Spare Command
+ *    Register" to move the pointer back at the beginning of the main data.
+ * 3/ It will read the content of the main area for a given size (pktsize) and
+ *    will feed the ECC engine with this buffer again.
+ * 4/ The ECC engine derives the ECC bytes for the given data and compare them
+ *    with the ones already received. It eventually trigger status flags and
+ *    then set the "Buffer Read Ready" flag.
+ * 5/ The corrected data is then available for reading from the data port
+ *    register.
+ *
+ * The hardware BCH ECC engine is known to be inconstent in BCH mode and never
+ * reports uncorrectable errors. Because of this bug, we have to use the
+ * software BCH implementation in the read path.
+ */
+static int anfc_read_page_hw_ecc(struct nand_chip *chip, u8 *buf,
+				 int oob_required, int page)
+{
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	struct anand *anand = to_anand(chip);
+	unsigned int len = mtd->writesize + (oob_required ? mtd->oobsize : 0);
+	unsigned int max_bitflips = 0;
+	dma_addr_t dma_addr;
+	int step, ret;
+	struct anfc_op nfc_op = {
+		.pkt_reg =
+			PKT_SIZE(chip->ecc.size) |
+			PKT_STEPS(chip->ecc.steps),
+		.addr1_reg =
+			(page & 0xFF) << (8 * (anand->caddr_cycles)) |
+			(((page >> 8) & 0xFF) << (8 * (1 + anand->caddr_cycles))),
+		.addr2_reg =
+			((page >> 16) & 0xFF) |
+			ADDR2_STRENGTH(anand->strength) |
+			ADDR2_CS(nfc->native_cs),
+		.cmd_reg =
+			CMD_1(NAND_CMD_READ0) |
+			CMD_2(NAND_CMD_READSTART) |
+			CMD_PAGE_SIZE(anand->page_sz) |
+			CMD_DMA_ENABLE |
+			CMD_NADDRS(anand->caddr_cycles +
+				   anand->raddr_cycles),
+		.prog_reg = PROG_PGRD,
+	};
+
+	dma_addr = dma_map_single(nfc->dev, (void *)buf, len, DMA_FROM_DEVICE);
+	if (dma_mapping_error(nfc->dev, dma_addr)) {
+		dev_err(nfc->dev, "Buffer mapping error");
+		return -EIO;
+	}
+
+	writel_relaxed(lower_32_bits(dma_addr), nfc->base + DMA_ADDR0_REG);
+	writel_relaxed(upper_32_bits(dma_addr), nfc->base + DMA_ADDR1_REG);
+
+	anfc_trigger_op(nfc, &nfc_op);
+
+	ret = anfc_wait_for_event(nfc, XFER_COMPLETE);
+	dma_unmap_single(nfc->dev, dma_addr, len, DMA_FROM_DEVICE);
+	if (ret) {
+		dev_err(nfc->dev, "Error reading page %d\n", page);
+		return ret;
+	}
+
+	/* Store the raw OOB bytes as well */
+	ret = nand_change_read_column_op(chip, mtd->writesize, chip->oob_poi,
+					 mtd->oobsize, 0);
+	if (ret)
+		return ret;
+
+	/*
+	 * For each step, compute by softare the BCH syndrome over the raw data.
+	 * Compare the theoretical amount of errors and compare with the
+	 * hardware engine feedback.
+	 */
+	for (step = 0; step < chip->ecc.steps; step++) {
+		u8 *raw_buf = &buf[step * chip->ecc.size];
+		unsigned int bit, byte;
+		int bf, i;
+
+		/* Extract the syndrome, it is not necessarily aligned */
+		memset(anand->hw_ecc, 0, chip->ecc.bytes);
+		nand_extract_bits(anand->hw_ecc, 0,
+				  &chip->oob_poi[mtd->oobsize - anand->ecc_total],
+				  anand->ecc_bits * step, anand->ecc_bits);
+
+		bf = bch_decode(anand->bch, raw_buf, chip->ecc.size,
+				anand->hw_ecc, NULL, NULL, anand->errloc);
+		if (!bf) {
+			continue;
+		} else if (bf > 0) {
+			for (i = 0; i < bf; i++) {
+				/* Only correct the data, not the syndrome */
+				if (anand->errloc[i] < (chip->ecc.size * 8)) {
+					bit = BIT(anand->errloc[i] & 7);
+					byte = anand->errloc[i] >> 3;
+					raw_buf[byte] ^= bit;
+				}
+			}
+
+			mtd->ecc_stats.corrected += bf;
+			max_bitflips = max_t(unsigned int, max_bitflips, bf);
+
+			continue;
+		}
+
+		bf = nand_check_erased_ecc_chunk(raw_buf, chip->ecc.size,
+						 NULL, 0, NULL, 0,
+						 chip->ecc.strength);
+		if (bf > 0) {
+			mtd->ecc_stats.corrected += bf;
+			max_bitflips = max_t(unsigned int, max_bitflips, bf);
+			memset(raw_buf, 0xFF, chip->ecc.size);
+		} else if (bf < 0) {
+			mtd->ecc_stats.failed++;
+		}
+	}
+
+	return 0;
+}
+
+static int anfc_sel_read_page_hw_ecc(struct nand_chip *chip, u8 *buf,
+				     int oob_required, int page)
+{
+	int ret;
+
+	ret = anfc_select_target(chip, chip->cur_cs);
+	if (ret)
+		return ret;
+
+	return anfc_read_page_hw_ecc(chip, buf, oob_required, page);
+};
+
+static int anfc_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
+				  int oob_required, int page)
+{
+	struct anand *anand = to_anand(chip);
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	unsigned int len = mtd->writesize + (oob_required ? mtd->oobsize : 0);
+	dma_addr_t dma_addr;
+	u8 status;
+	int ret;
+	struct anfc_op nfc_op = {
+		.pkt_reg =
+			PKT_SIZE(chip->ecc.size) |
+			PKT_STEPS(chip->ecc.steps),
+		.addr1_reg =
+			(page & 0xFF) << (8 * (anand->caddr_cycles)) |
+			(((page >> 8) & 0xFF) << (8 * (1 + anand->caddr_cycles))),
+		.addr2_reg =
+			((page >> 16) & 0xFF) |
+			ADDR2_STRENGTH(anand->strength) |
+			ADDR2_CS(nfc->native_cs),
+		.cmd_reg =
+			CMD_1(NAND_CMD_SEQIN) |
+			CMD_2(NAND_CMD_PAGEPROG) |
+			CMD_PAGE_SIZE(anand->page_sz) |
+			CMD_DMA_ENABLE |
+			CMD_NADDRS(anand->caddr_cycles +
+				   anand->raddr_cycles) |
+			CMD_ECC_ENABLE,
+		.prog_reg = PROG_PGPROG,
+	};
+
+	writel_relaxed(anand->ecc_conf, nfc->base + ECC_CONF_REG);
+	writel_relaxed(ECC_SP_CMD1(NAND_CMD_RNDIN) |
+		       ECC_SP_ADDRS(anand->caddr_cycles),
+		       nfc->base + ECC_SP_REG);
+
+	dma_addr = dma_map_single(nfc->dev, (void *)buf, len, DMA_TO_DEVICE);
+	if (dma_mapping_error(nfc->dev, dma_addr)) {
+		dev_err(nfc->dev, "Buffer mapping error");
+		return -EIO;
+	}
+
+	writel_relaxed(lower_32_bits(dma_addr), nfc->base + DMA_ADDR0_REG);
+	writel_relaxed(upper_32_bits(dma_addr), nfc->base + DMA_ADDR1_REG);
+
+	anfc_trigger_op(nfc, &nfc_op);
+	ret = anfc_wait_for_event(nfc, XFER_COMPLETE);
+	dma_unmap_single(nfc->dev, dma_addr, len, DMA_TO_DEVICE);
+	if (ret) {
+		dev_err(nfc->dev, "Error writing page %d\n", page);
+		return ret;
+	}
+
+	/* Spare data is not protected */
+	if (oob_required) {
+		ret = nand_write_oob_std(chip, page);
+		if (ret)
+			return ret;
+	}
+
+	/* Check write status on the chip side */
+	ret = nand_status_op(chip, &status);
+	if (ret)
+		return ret;
+
+	if (status & NAND_STATUS_FAIL)
+		return -EIO;
+
+	return 0;
+}
+
+static int anfc_sel_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
+				      int oob_required, int page)
+{
+	int ret;
+
+	ret = anfc_select_target(chip, chip->cur_cs);
+	if (ret)
+		return ret;
+
+	return anfc_write_page_hw_ecc(chip, buf, oob_required, page);
+};
+
+/* NAND framework ->exec_op() hooks and related helpers */
+static int anfc_parse_instructions(struct nand_chip *chip,
+				   const struct nand_subop *subop,
+				   struct anfc_op *nfc_op)
+{
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	struct anand *anand = to_anand(chip);
+	const struct nand_op_instr *instr = NULL;
+	bool first_cmd = true;
+	unsigned int op_id;
+	int ret, i;
+
+	memset(nfc_op, 0, sizeof(*nfc_op));
+	nfc_op->addr2_reg = ADDR2_CS(nfc->native_cs);
+	nfc_op->cmd_reg = CMD_PAGE_SIZE(anand->page_sz);
+
+	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
+		unsigned int offset, naddrs, pktsize;
+		const u8 *addrs;
+		u8 *buf;
+
+		instr = &subop->instrs[op_id];
+
+		switch (instr->type) {
+		case NAND_OP_CMD_INSTR:
+			if (first_cmd)
+				nfc_op->cmd_reg |= CMD_1(instr->ctx.cmd.opcode);
+			else
+				nfc_op->cmd_reg |= CMD_2(instr->ctx.cmd.opcode);
+
+			first_cmd = false;
+			break;
+
+		case NAND_OP_ADDR_INSTR:
+			offset = nand_subop_get_addr_start_off(subop, op_id);
+			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
+			addrs = &instr->ctx.addr.addrs[offset];
+			nfc_op->cmd_reg |= CMD_NADDRS(naddrs);
+
+			for (i = 0; i < min(ANFC_MAX_ADDR_CYC, naddrs); i++) {
+				if (i < 4)
+					nfc_op->addr1_reg |= (u32)addrs[i] << i * 8;
+				else
+					nfc_op->addr2_reg |= addrs[i];
+			}
+
+			break;
+		case NAND_OP_DATA_IN_INSTR:
+			nfc_op->read = true;
+			fallthrough;
+		case NAND_OP_DATA_OUT_INSTR:
+			offset = nand_subop_get_data_start_off(subop, op_id);
+			buf = instr->ctx.data.buf.in;
+			nfc_op->buf = &buf[offset];
+			nfc_op->len = nand_subop_get_data_len(subop, op_id);
+			ret = anfc_pkt_len_config(nfc_op->len, &nfc_op->steps,
+						  &pktsize);
+			if (ret)
+				return ret;
+
+			/*
+			 * Number of DATA cycles must be aligned on 4, this
+			 * means the controller might read/write more than
+			 * requested. This is harmless most of the time as extra
+			 * DATA are discarded in the write path and read pointer
+			 * adjusted in the read path.
+			 *
+			 * FIXME: The core should mark operations where
+			 * reading/writing more is allowed so the exec_op()
+			 * implementation can take the right decision when the
+			 * alignment constraint is not met: adjust the number of
+			 * DATA cycles when it's allowed, reject the operation
+			 * otherwise.
+			 */
+			nfc_op->pkt_reg |= PKT_SIZE(round_up(pktsize, 4)) |
+					   PKT_STEPS(nfc_op->steps);
+			break;
+		case NAND_OP_WAITRDY_INSTR:
+			nfc_op->rdy_timeout_ms = instr->ctx.waitrdy.timeout_ms;
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static int anfc_rw_pio_op(struct arasan_nfc *nfc, struct anfc_op *nfc_op)
+{
+	unsigned int dwords = (nfc_op->len / 4) / nfc_op->steps;
+	unsigned int last_len = nfc_op->len % 4;
+	unsigned int offset, dir;
+	u8 *buf = nfc_op->buf;
+	int ret, i;
+
+	for (i = 0; i < nfc_op->steps; i++) {
+		dir = nfc_op->read ? READ_READY : WRITE_READY;
+		ret = anfc_wait_for_event(nfc, dir);
+		if (ret) {
+			dev_err(nfc->dev, "PIO %s ready signal not received\n",
+				nfc_op->read ? "Read" : "Write");
+			return ret;
+		}
+
+		offset = i * (dwords * 4);
+		if (nfc_op->read)
+			ioread32_rep(nfc->base + DATA_PORT_REG, &buf[offset],
+				     dwords);
+		else
+			iowrite32_rep(nfc->base + DATA_PORT_REG, &buf[offset],
+				      dwords);
+	}
+
+	if (last_len) {
+		u32 remainder;
+
+		offset = nfc_op->len - last_len;
+
+		if (nfc_op->read) {
+			remainder = readl_relaxed(nfc->base + DATA_PORT_REG);
+			memcpy(&buf[offset], &remainder, last_len);
+		} else {
+			memcpy(&remainder, &buf[offset], last_len);
+			writel_relaxed(remainder, nfc->base + DATA_PORT_REG);
+		}
+	}
+
+	return anfc_wait_for_event(nfc, XFER_COMPLETE);
+}
+
+static int anfc_misc_data_type_exec(struct nand_chip *chip,
+				    const struct nand_subop *subop,
+				    u32 prog_reg)
+{
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	struct anfc_op nfc_op = {};
+	int ret;
+
+	ret = anfc_parse_instructions(chip, subop, &nfc_op);
+	if (ret)
+		return ret;
+
+	nfc_op.prog_reg = prog_reg;
+	anfc_trigger_op(nfc, &nfc_op);
+
+	if (nfc_op.rdy_timeout_ms) {
+		ret = anfc_wait_for_rb(nfc, chip, nfc_op.rdy_timeout_ms);
+		if (ret)
+			return ret;
+	}
+
+	return anfc_rw_pio_op(nfc, &nfc_op);
+}
+
+static int anfc_param_read_type_exec(struct nand_chip *chip,
+				     const struct nand_subop *subop)
+{
+	return anfc_misc_data_type_exec(chip, subop, PROG_RDPARAM);
+}
+
+static int anfc_data_read_type_exec(struct nand_chip *chip,
+				    const struct nand_subop *subop)
+{
+	u32 prog_reg = PROG_PGRD;
+
+	/*
+	 * Experience shows that while in SDR mode sending a CHANGE READ COLUMN
+	 * command through the READ PAGE "type" always works fine, when in
+	 * NV-DDR mode the same command simply fails. However, it was also
+	 * spotted that any CHANGE READ COLUMN command sent through the CHANGE
+	 * READ COLUMN ENHANCED "type" would correctly work in both cases (SDR
+	 * and NV-DDR). So, for simplicity, let's program the controller with
+	 * the CHANGE READ COLUMN ENHANCED "type" whenever we are requested to
+	 * perform a CHANGE READ COLUMN operation.
+	 */
+	if (subop->instrs[0].ctx.cmd.opcode == NAND_CMD_RNDOUT &&
+	    subop->instrs[2].ctx.cmd.opcode == NAND_CMD_RNDOUTSTART)
+		prog_reg = PROG_CHG_RD_COL_ENH;
+
+	return anfc_misc_data_type_exec(chip, subop, prog_reg);
+}
+
+static int anfc_param_write_type_exec(struct nand_chip *chip,
+				      const struct nand_subop *subop)
+{
+	return anfc_misc_data_type_exec(chip, subop, PROG_SET_FEATURE);
+}
+
+static int anfc_data_write_type_exec(struct nand_chip *chip,
+				     const struct nand_subop *subop)
+{
+	return anfc_misc_data_type_exec(chip, subop, PROG_PGPROG);
+}
+
+static int anfc_misc_zerolen_type_exec(struct nand_chip *chip,
+				       const struct nand_subop *subop,
+				       u32 prog_reg)
+{
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	struct anfc_op nfc_op = {};
+	int ret;
+
+	ret = anfc_parse_instructions(chip, subop, &nfc_op);
+	if (ret)
+		return ret;
+
+	nfc_op.prog_reg = prog_reg;
+	anfc_trigger_op(nfc, &nfc_op);
+
+	ret = anfc_wait_for_event(nfc, XFER_COMPLETE);
+	if (ret)
+		return ret;
+
+	if (nfc_op.rdy_timeout_ms)
+		ret = anfc_wait_for_rb(nfc, chip, nfc_op.rdy_timeout_ms);
+
+	return ret;
+}
+
+static int anfc_status_type_exec(struct nand_chip *chip,
+				 const struct nand_subop *subop)
+{
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	u32 tmp;
+	int ret;
+
+	/* See anfc_check_op() for details about this constraint */
+	if (subop->instrs[0].ctx.cmd.opcode != NAND_CMD_STATUS)
+		return -ENOTSUPP;
+
+	ret = anfc_misc_zerolen_type_exec(chip, subop, PROG_STATUS);
+	if (ret)
+		return ret;
+
+	tmp = readl_relaxed(nfc->base + FLASH_STS_REG);
+	memcpy(subop->instrs[1].ctx.data.buf.in, &tmp, 1);
+
+	return 0;
+}
+
+static int anfc_reset_type_exec(struct nand_chip *chip,
+				const struct nand_subop *subop)
+{
+	return anfc_misc_zerolen_type_exec(chip, subop, PROG_RST);
+}
+
+static int anfc_erase_type_exec(struct nand_chip *chip,
+				const struct nand_subop *subop)
+{
+	return anfc_misc_zerolen_type_exec(chip, subop, PROG_ERASE);
+}
+
+static int anfc_wait_type_exec(struct nand_chip *chip,
+			       const struct nand_subop *subop)
+{
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	struct anfc_op nfc_op = {};
+	int ret;
+
+	ret = anfc_parse_instructions(chip, subop, &nfc_op);
+	if (ret)
+		return ret;
+
+	return anfc_wait_for_rb(nfc, chip, nfc_op.rdy_timeout_ms);
+}
+
+static const struct nand_op_parser anfc_op_parser = NAND_OP_PARSER(
+	NAND_OP_PARSER_PATTERN(
+		anfc_param_read_type_exec,
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_ADDR_ELEM(false, ANFC_MAX_ADDR_CYC),
+		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true),
+		NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, ANFC_MAX_CHUNK_SIZE)),
+	NAND_OP_PARSER_PATTERN(
+		anfc_param_write_type_exec,
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_ADDR_ELEM(false, ANFC_MAX_ADDR_CYC),
+		NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, ANFC_MAX_PARAM_SIZE)),
+	NAND_OP_PARSER_PATTERN(
+		anfc_data_read_type_exec,
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_ADDR_ELEM(false, ANFC_MAX_ADDR_CYC),
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true),
+		NAND_OP_PARSER_PAT_DATA_IN_ELEM(true, ANFC_MAX_CHUNK_SIZE)),
+	NAND_OP_PARSER_PATTERN(
+		anfc_data_write_type_exec,
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_ADDR_ELEM(false, ANFC_MAX_ADDR_CYC),
+		NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, ANFC_MAX_CHUNK_SIZE),
+		NAND_OP_PARSER_PAT_CMD_ELEM(false)),
+	NAND_OP_PARSER_PATTERN(
+		anfc_reset_type_exec,
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
+	NAND_OP_PARSER_PATTERN(
+		anfc_erase_type_exec,
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_ADDR_ELEM(false, ANFC_MAX_ADDR_CYC),
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
+	NAND_OP_PARSER_PATTERN(
+		anfc_status_type_exec,
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, ANFC_MAX_CHUNK_SIZE)),
+	NAND_OP_PARSER_PATTERN(
+		anfc_wait_type_exec,
+		NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
+	);
+
+static int anfc_check_op(struct nand_chip *chip,
+			 const struct nand_operation *op)
+{
+	const struct nand_op_instr *instr;
+	int op_id;
+
+	/*
+	 * The controller abstracts all the NAND operations and do not support
+	 * data only operations.
+	 *
+	 * TODO: The nand_op_parser framework should be extended to
+	 * support custom checks on DATA instructions.
+	 */
+	for (op_id = 0; op_id < op->ninstrs; op_id++) {
+		instr = &op->instrs[op_id];
+
+		switch (instr->type) {
+		case NAND_OP_ADDR_INSTR:
+			if (instr->ctx.addr.naddrs > ANFC_MAX_ADDR_CYC)
+				return -ENOTSUPP;
+
+			break;
+		case NAND_OP_DATA_IN_INSTR:
+		case NAND_OP_DATA_OUT_INSTR:
+			if (instr->ctx.data.len > ANFC_MAX_CHUNK_SIZE)
+				return -ENOTSUPP;
+
+			if (anfc_pkt_len_config(instr->ctx.data.len, NULL, NULL))
+				return -ENOTSUPP;
+
+			break;
+		default:
+			break;
+		}
+	}
+
+	/*
+	 * The controller does not allow to proceed with a CMD+DATA_IN cycle
+	 * manually on the bus by reading data from the data register. Instead,
+	 * the controller abstract a status read operation with its own status
+	 * register after ordering a read status operation. Hence, we cannot
+	 * support any CMD+DATA_IN operation other than a READ STATUS.
+	 *
+	 * TODO: The nand_op_parser() framework should be extended to describe
+	 * fixed patterns instead of open-coding this check here.
+	 */
+	if (op->ninstrs == 2 &&
+	    op->instrs[0].type == NAND_OP_CMD_INSTR &&
+	    op->instrs[0].ctx.cmd.opcode != NAND_CMD_STATUS &&
+	    op->instrs[1].type == NAND_OP_DATA_IN_INSTR)
+		return -ENOTSUPP;
+
+	return nand_op_parser_exec_op(chip, &anfc_op_parser, op, true);
+}
+
+static int anfc_exec_op(struct nand_chip *chip,
+			const struct nand_operation *op,
+			bool check_only)
+{
+	int ret;
+
+	if (check_only)
+		return anfc_check_op(chip, op);
+
+	ret = anfc_select_target(chip, op->cs);
+	if (ret)
+		return ret;
+
+	return nand_op_parser_exec_op(chip, &anfc_op_parser, op, check_only);
+}
+
+static int anfc_setup_interface(struct nand_chip *chip, int target,
+				const struct nand_interface_config *conf)
+{
+	struct anand *anand = to_anand(chip);
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	struct device_node *np = nfc->dev->of_node;
+	const struct nand_sdr_timings *sdr;
+	const struct nand_nvddr_timings *nvddr;
+	unsigned int tccs_min, dqs_mode, fast_tcad;
+
+	if (nand_interface_is_nvddr(conf)) {
+		nvddr = nand_get_nvddr_timings(conf);
+		if (IS_ERR(nvddr))
+			return PTR_ERR(nvddr);
+	} else {
+		sdr = nand_get_sdr_timings(conf);
+		if (IS_ERR(sdr))
+			return PTR_ERR(sdr);
+	}
+
+	if (target < 0)
+		return 0;
+
+	if (nand_interface_is_sdr(conf)) {
+		anand->data_iface = DIFACE_SDR |
+				    DIFACE_SDR_MODE(conf->timings.mode);
+		anand->timings = 0;
+	} else {
+		anand->data_iface = DIFACE_NVDDR |
+				    DIFACE_DDR_MODE(conf->timings.mode);
+
+		if (conf->timings.nvddr.tCCS_min <= 100000)
+			tccs_min = TCCS_TIME_100NS;
+		else if (conf->timings.nvddr.tCCS_min <= 200000)
+			tccs_min = TCCS_TIME_200NS;
+		else if (conf->timings.nvddr.tCCS_min <= 300000)
+			tccs_min = TCCS_TIME_300NS;
+		else
+			tccs_min = TCCS_TIME_500NS;
+
+		fast_tcad = 0;
+		if (conf->timings.nvddr.tCAD_min < 45000)
+			fast_tcad = FAST_TCAD;
+
+		switch (conf->timings.mode) {
+		case 5:
+		case 4:
+			dqs_mode = 2;
+			break;
+		case 3:
+			dqs_mode = 3;
+			break;
+		case 2:
+			dqs_mode = 4;
+			break;
+		case 1:
+			dqs_mode = 5;
+			break;
+		case 0:
+		default:
+			dqs_mode = 6;
+			break;
+		}
+
+		anand->timings = tccs_min | fast_tcad |
+				 DQS_BUFF_SEL_IN(dqs_mode) |
+				 DQS_BUFF_SEL_OUT(dqs_mode);
+	}
+
+	if (nand_interface_is_sdr(conf)) {
+		anand->clk = ANFC_XLNX_SDR_DFLT_CORE_CLK;
+	} else {
+		/* ONFI timings are defined in picoseconds */
+		anand->clk = div_u64((u64)NSEC_PER_SEC * 1000,
+				     conf->timings.nvddr.tCK_min);
+	}
+
+	/*
+	 * Due to a hardware bug in the ZynqMP SoC, SDR timing modes 0-1 work
+	 * with f > 90MHz (default clock is 100MHz) but signals are unstable
+	 * with higher modes. Hence we decrease a little bit the clock rate to
+	 * 80MHz when using SDR modes 2-5 with this SoC.
+	 */
+	if (of_device_is_compatible(np, "xlnx,zynqmp-nand-controller") &&
+	    nand_interface_is_sdr(conf) && conf->timings.mode >= 2)
+		anand->clk = ANFC_XLNX_SDR_HS_CORE_CLK;
+
+	return 0;
+}
+
+static int anfc_calc_hw_ecc_bytes(int step_size, int strength)
+{
+	unsigned int bch_gf_mag, ecc_bits;
+
+	switch (step_size) {
+	case SZ_512:
+		bch_gf_mag = 13;
+		break;
+	case SZ_1K:
+		bch_gf_mag = 14;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	ecc_bits = bch_gf_mag * strength;
+
+	return DIV_ROUND_UP(ecc_bits, 8);
+}
+
+static const int anfc_hw_ecc_512_strengths[] = {4, 8, 12};
+
+static const int anfc_hw_ecc_1024_strengths[] = {24};
+
+static const struct nand_ecc_step_info anfc_hw_ecc_step_infos[] = {
+	{
+		.stepsize = SZ_512,
+		.strengths = anfc_hw_ecc_512_strengths,
+		.nstrengths = ARRAY_SIZE(anfc_hw_ecc_512_strengths),
+	},
+	{
+		.stepsize = SZ_1K,
+		.strengths = anfc_hw_ecc_1024_strengths,
+		.nstrengths = ARRAY_SIZE(anfc_hw_ecc_1024_strengths),
+	},
+};
+
+static const struct nand_ecc_caps anfc_hw_ecc_caps = {
+	.stepinfos = anfc_hw_ecc_step_infos,
+	.nstepinfos = ARRAY_SIZE(anfc_hw_ecc_step_infos),
+	.calc_ecc_bytes = anfc_calc_hw_ecc_bytes,
+};
+
+static int anfc_init_hw_ecc_controller(struct arasan_nfc *nfc,
+				       struct nand_chip *chip)
+{
+	struct anand *anand = to_anand(chip);
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	struct nand_ecc_ctrl *ecc = &chip->ecc;
+	unsigned int bch_prim_poly = 0, bch_gf_mag = 0, ecc_offset;
+	int ret;
+
+	switch (mtd->writesize) {
+	case SZ_512:
+	case SZ_2K:
+	case SZ_4K:
+	case SZ_8K:
+	case SZ_16K:
+		break;
+	default:
+		dev_err(nfc->dev, "Unsupported page size %d\n", mtd->writesize);
+		return -EINVAL;
+	}
+
+	ret = nand_ecc_choose_conf(chip, &anfc_hw_ecc_caps, mtd->oobsize);
+	if (ret)
+		return ret;
+
+	switch (ecc->strength) {
+	case 12:
+		anand->strength = 0x1;
+		break;
+	case 8:
+		anand->strength = 0x2;
+		break;
+	case 4:
+		anand->strength = 0x3;
+		break;
+	case 24:
+		anand->strength = 0x4;
+		break;
+	default:
+		dev_err(nfc->dev, "Unsupported strength %d\n", ecc->strength);
+		return -EINVAL;
+	}
+
+	switch (ecc->size) {
+	case SZ_512:
+		bch_gf_mag = 13;
+		bch_prim_poly = 0x201b;
+		break;
+	case SZ_1K:
+		bch_gf_mag = 14;
+		bch_prim_poly = 0x4443;
+		break;
+	default:
+		dev_err(nfc->dev, "Unsupported step size %d\n", ecc->strength);
+		return -EINVAL;
+	}
+
+	mtd_set_ooblayout(mtd, nand_get_large_page_ooblayout());
+
+	ecc->steps = mtd->writesize / ecc->size;
+	ecc->algo = NAND_ECC_ALGO_BCH;
+	anand->ecc_bits = bch_gf_mag * ecc->strength;
+	ecc->bytes = DIV_ROUND_UP(anand->ecc_bits, 8);
+	anand->ecc_total = DIV_ROUND_UP(anand->ecc_bits * ecc->steps, 8);
+	ecc_offset = mtd->writesize + mtd->oobsize - anand->ecc_total;
+	anand->ecc_conf = ECC_CONF_COL(ecc_offset) |
+			  ECC_CONF_LEN(anand->ecc_total) |
+			  ECC_CONF_BCH_EN;
+
+	anand->errloc = devm_kmalloc_array(nfc->dev, ecc->strength,
+					   sizeof(*anand->errloc), GFP_KERNEL);
+	if (!anand->errloc)
+		return -ENOMEM;
+
+	anand->hw_ecc = devm_kmalloc(nfc->dev, ecc->bytes, GFP_KERNEL);
+	if (!anand->hw_ecc)
+		return -ENOMEM;
+
+	/* Enforce bit swapping to fit the hardware */
+	anand->bch = bch_init(bch_gf_mag, ecc->strength, bch_prim_poly, true);
+	if (!anand->bch)
+		return -EINVAL;
+
+	ecc->read_page = anfc_sel_read_page_hw_ecc;
+	ecc->write_page = anfc_sel_write_page_hw_ecc;
+
+	return 0;
+}
+
+static int anfc_attach_chip(struct nand_chip *chip)
+{
+	struct anand *anand = to_anand(chip);
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	int ret = 0;
+
+	if (mtd->writesize <= SZ_512)
+		anand->caddr_cycles = 1;
+	else
+		anand->caddr_cycles = 2;
+
+	if (chip->options & NAND_ROW_ADDR_3)
+		anand->raddr_cycles = 3;
+	else
+		anand->raddr_cycles = 2;
+
+	switch (mtd->writesize) {
+	case 512:
+		anand->page_sz = 0;
+		break;
+	case 1024:
+		anand->page_sz = 5;
+		break;
+	case 2048:
+		anand->page_sz = 1;
+		break;
+	case 4096:
+		anand->page_sz = 2;
+		break;
+	case 8192:
+		anand->page_sz = 3;
+		break;
+	case 16384:
+		anand->page_sz = 4;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/* These hooks are valid for all ECC providers */
+	chip->ecc.read_page_raw = nand_monolithic_read_page_raw;
+	chip->ecc.write_page_raw = nand_monolithic_write_page_raw;
+
+	switch (chip->ecc.engine_type) {
+	case NAND_ECC_ENGINE_TYPE_NONE:
+	case NAND_ECC_ENGINE_TYPE_SOFT:
+	case NAND_ECC_ENGINE_TYPE_ON_DIE:
+		break;
+	case NAND_ECC_ENGINE_TYPE_ON_HOST:
+		ret = anfc_init_hw_ecc_controller(nfc, chip);
+		break;
+	default:
+		dev_err(nfc->dev, "Unsupported ECC mode: %d\n",
+			chip->ecc.engine_type);
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+static void anfc_detach_chip(struct nand_chip *chip)
+{
+	struct anand *anand = to_anand(chip);
+
+	if (anand->bch)
+		bch_free(anand->bch);
+}
+
+static const struct nand_controller_ops anfc_ops = {
+	.exec_op = anfc_exec_op,
+	.setup_interface = anfc_setup_interface,
+	.attach_chip = anfc_attach_chip,
+	.detach_chip = anfc_detach_chip,
+};
+
+static int anfc_chip_init(struct arasan_nfc *nfc, struct device_node *np)
+{
+	struct anand *anand;
+	struct nand_chip *chip;
+	struct mtd_info *mtd;
+	int rb, ret, i;
+
+	anand = devm_kzalloc(nfc->dev, sizeof(*anand), GFP_KERNEL);
+	if (!anand)
+		return -ENOMEM;
+
+	/* Chip-select init */
+	anand->ncs_idx = of_property_count_elems_of_size(np, "reg", sizeof(u32));
+	if (anand->ncs_idx <= 0 || anand->ncs_idx > nfc->ncs) {
+		dev_err(nfc->dev, "Invalid reg property\n");
+		return -EINVAL;
+	}
+
+	anand->cs_idx = devm_kcalloc(nfc->dev, anand->ncs_idx,
+				     sizeof(*anand->cs_idx), GFP_KERNEL);
+	if (!anand->cs_idx)
+		return -ENOMEM;
+
+	for (i = 0; i < anand->ncs_idx; i++) {
+		ret = of_property_read_u32_index(np, "reg", i,
+						 &anand->cs_idx[i]);
+		if (ret) {
+			dev_err(nfc->dev, "invalid CS property: %d\n", ret);
+			return ret;
+		}
+	}
+
+	/* Ready-busy init */
+	ret = of_property_read_u32(np, "nand-rb", &rb);
+	if (ret)
+		return ret;
+
+	if (rb >= ANFC_MAX_CS) {
+		dev_err(nfc->dev, "Wrong RB %d\n", rb);
+		return -EINVAL;
+	}
+
+	anand->rb = rb;
+
+	chip = &anand->chip;
+	mtd = nand_to_mtd(chip);
+	mtd->dev.parent = nfc->dev;
+	chip->controller = &nfc->controller;
+	chip->options = NAND_BUSWIDTH_AUTO | NAND_NO_SUBPAGE_WRITE |
+			NAND_USES_DMA;
+
+	nand_set_flash_node(chip, np);
+	if (!mtd->name) {
+		dev_err(nfc->dev, "NAND label property is mandatory\n");
+		return -EINVAL;
+	}
+
+	ret = nand_scan(chip, anand->ncs_idx);
+	if (ret) {
+		dev_err(nfc->dev, "Scan operation failed\n");
+		return ret;
+	}
+
+	ret = mtd_device_register(mtd, NULL, 0);
+	if (ret) {
+		nand_cleanup(chip);
+		return ret;
+	}
+
+	list_add_tail(&anand->node, &nfc->chips);
+
+	return 0;
+}
+
+static void anfc_chips_cleanup(struct arasan_nfc *nfc)
+{
+	struct anand *anand, *tmp;
+	struct nand_chip *chip;
+	int ret;
+
+	list_for_each_entry_safe(anand, tmp, &nfc->chips, node) {
+		chip = &anand->chip;
+		ret = mtd_device_unregister(nand_to_mtd(chip));
+		WARN_ON(ret);
+		nand_cleanup(chip);
+		list_del(&anand->node);
+	}
+}
+
+static int anfc_chips_init(struct arasan_nfc *nfc)
+{
+	struct device_node *np = nfc->dev->of_node, *nand_np;
+	int nchips = of_get_child_count(np);
+	int ret;
+
+	if (!nchips) {
+		dev_err(nfc->dev, "Incorrect number of NAND chips (%d)\n",
+			nchips);
+		return -EINVAL;
+	}
+
+	for_each_child_of_node(np, nand_np) {
+		ret = anfc_chip_init(nfc, nand_np);
+		if (ret) {
+			of_node_put(nand_np);
+			anfc_chips_cleanup(nfc);
+			break;
+		}
+	}
+
+	return ret;
+}
+
+static void anfc_reset(struct arasan_nfc *nfc)
+{
+	/* Disable interrupt signals */
+	writel_relaxed(0, nfc->base + INTR_SIG_EN_REG);
+
+	/* Enable interrupt status */
+	writel_relaxed(EVENT_MASK, nfc->base + INTR_STS_EN_REG);
+
+	nfc->cur_cs = -1;
+}
+
+static int anfc_parse_cs(struct arasan_nfc *nfc)
+{
+	int ret;
+
+	/* Check the gpio-cs property */
+	ret = rawnand_dt_parse_gpio_cs(nfc->dev, &nfc->cs_array, &nfc->ncs);
+	if (ret)
+		return ret;
+
+	/*
+	 * The controller native CS cannot be both disabled at the same time.
+	 * Hence, only one native CS can be used if GPIO CS are needed, so that
+	 * the other is selected when a non-native CS must be asserted (not
+	 * wired physically or configured as GPIO instead of NAND CS). In this
+	 * case, the "not" chosen CS is assigned to nfc->spare_cs and selected
+	 * whenever a GPIO CS must be asserted.
+	 */
+	if (nfc->cs_array && nfc->ncs > 2) {
+		if (!nfc->cs_array[0] && !nfc->cs_array[1]) {
+			dev_err(nfc->dev,
+				"Assign a single native CS when using GPIOs\n");
+			return -EINVAL;
+		}
+
+		if (nfc->cs_array[0])
+			nfc->spare_cs = 0;
+		else
+			nfc->spare_cs = 1;
+	}
+
+	if (!nfc->cs_array) {
+		nfc->cs_array = anfc_default_cs_array;
+		nfc->ncs = ANFC_MAX_CS;
+		return 0;
+	}
+
+	return 0;
+}
+
+static int anfc_probe(struct platform_device *pdev)
+{
+	struct arasan_nfc *nfc;
+	int ret;
+
+	nfc = devm_kzalloc(&pdev->dev, sizeof(*nfc), GFP_KERNEL);
+	if (!nfc)
+		return -ENOMEM;
+
+	nfc->dev = &pdev->dev;
+	nand_controller_init(&nfc->controller);
+	nfc->controller.ops = &anfc_ops;
+	INIT_LIST_HEAD(&nfc->chips);
+
+	nfc->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(nfc->base))
+		return PTR_ERR(nfc->base);
+
+	anfc_reset(nfc);
+
+	nfc->controller_clk = devm_clk_get_enabled(&pdev->dev, "controller");
+	if (IS_ERR(nfc->controller_clk))
+		return PTR_ERR(nfc->controller_clk);
+
+	nfc->bus_clk = devm_clk_get_enabled(&pdev->dev, "bus");
+	if (IS_ERR(nfc->bus_clk))
+		return PTR_ERR(nfc->bus_clk);
+
+	ret = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
+	if (ret)
+		return ret;
+
+	ret = anfc_parse_cs(nfc);
+	if (ret)
+		return ret;
+
+	ret = anfc_chips_init(nfc);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, nfc);
+
+	return 0;
+}
+
+static void anfc_remove(struct platform_device *pdev)
+{
+	struct arasan_nfc *nfc = platform_get_drvdata(pdev);
+
+	anfc_chips_cleanup(nfc);
+}
+
+static const struct of_device_id anfc_ids[] = {
+	{
+		.compatible = "xlnx,zynqmp-nand-controller",
+	},
+	{
+		.compatible = "arasan,nfc-v3p10",
+	},
+	{}
+};
+MODULE_DEVICE_TABLE(of, anfc_ids);
+
+static struct platform_driver anfc_driver = {
+	.driver = {
+		.name = "arasan-nand-controller",
+		.of_match_table = anfc_ids,
+	},
+	.probe = anfc_probe,
+	.remove_new = anfc_remove,
+};
+module_platform_driver(anfc_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Punnaiah Choudary Kalluri <punnaia@xilinx.com>");
+MODULE_AUTHOR("Naga Sureshkumar Relli <nagasure@xilinx.com>");
+MODULE_AUTHOR("Miquel Raynal <miquel.raynal@bootlin.com>");
+MODULE_DESCRIPTION("Arasan NAND Flash Controller Driver");