Adding upstream version 6.8.9.upstream/6.8.9

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

5 files changed, 173 insertions, 41 deletions

diff --git a/drivers/net/dsa/microchip/ksz8.h b/drivers/net/dsa/microchip/ksz8.h
index 4cea811e73..1a5225264e 100644
--- a/drivers/net/dsa/microchip/ksz8.h
+++ b/drivers/net/dsa/microchip/ksz8.h
@@ -56,5 +56,9 @@ int ksz8_reset_switch(struct ksz_device *dev);
 int ksz8_switch_init(struct ksz_device *dev);
 void ksz8_switch_exit(struct ksz_device *dev);
 int ksz8_change_mtu(struct ksz_device *dev, int port, int mtu);
+void ksz8_phylink_mac_link_up(struct ksz_device *dev, int port,
+			      unsigned int mode, phy_interface_t interface,
+			      struct phy_device *phydev, int speed, int duplex,
+			      bool tx_pause, bool rx_pause);
 
 #endif
diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index 9048d1f196..c3da97abce 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -1358,6 +1358,9 @@ static void ksz8795_cpu_interface_select(struct ksz_device *dev, int port)
 {
 	struct ksz_port *p = &dev->ports[port];
 
+	if (!ksz_is_ksz87xx(dev))
+		return;
+
 	if (!p->interface && dev->compat_interface) {
 		dev_warn(dev->dev,
 			 "Using legacy switch \"phy-mode\" property, because it is missing on port %d node. "
@@ -1391,18 +1394,29 @@ void ksz8_port_setup(struct ksz_device *dev, int port, bool cpu_port)
 	/* enable 802.1p priority */
 	ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_802_1P_ENABLE, true);
 
-	if (cpu_port) {
-		if (!ksz_is_ksz88x3(dev))
-			ksz8795_cpu_interface_select(dev, port);
-
+	if (cpu_port)
 		member = dsa_user_ports(ds);
-	} else {
+	else
 		member = BIT(dsa_upstream_port(ds, port));
-	}
 
 	ksz8_cfg_port_member(dev, port, member);
 }
 
+static void ksz88x3_config_rmii_clk(struct ksz_device *dev)
+{
+	struct dsa_port *cpu_dp = dsa_to_port(dev->ds, dev->cpu_port);
+	bool rmii_clk_internal;
+
+	if (!ksz_is_ksz88x3(dev))
+		return;
+
+	rmii_clk_internal = of_property_read_bool(cpu_dp->dn,
+						  "microchip,rmii-clk-internal");
+
+	ksz_cfg(dev, KSZ88X3_REG_FVID_AND_HOST_MODE,
+		KSZ88X3_PORT3_RMII_CLK_INTERNAL, rmii_clk_internal);
+}
+
 void ksz8_config_cpu_port(struct dsa_switch *ds)
 {
 	struct ksz_device *dev = ds->priv;
@@ -1419,6 +1433,9 @@ void ksz8_config_cpu_port(struct dsa_switch *ds)
 
 	ksz8_port_setup(dev, dev->cpu_port, true);
 
+	ksz8795_cpu_interface_select(dev, dev->cpu_port);
+	ksz88x3_config_rmii_clk(dev);
+
 	for (i = 0; i < dev->phy_port_cnt; i++) {
 		ksz_port_stp_state_set(ds, i, BR_STATE_DISABLED);
 	}
@@ -1439,6 +1456,127 @@ void ksz8_config_cpu_port(struct dsa_switch *ds)
 	}
 }
 
+/**
+ * ksz8_phy_port_link_up - Configures ports with integrated PHYs
+ * @dev: The KSZ device instance.
+ * @port: The port number to configure.
+ * @duplex: The desired duplex mode.
+ * @tx_pause: If true, enables transmit pause.
+ * @rx_pause: If true, enables receive pause.
+ *
+ * Description:
+ * The function configures flow control settings for a given port based on the
+ * desired settings and current duplex mode.
+ *
+ * According to the KSZ8873 datasheet, the PORT_FORCE_FLOW_CTRL bit in the
+ * Port Control 2 register (0x1A for Port 1, 0x22 for Port 2, 0x32 for Port 3)
+ * determines how flow control is handled on the port:
+ *    "1 = will always enable full-duplex flow control on the port, regardless
+ *         of AN result.
+ *     0 = full-duplex flow control is enabled based on AN result."
+ *
+ * This means that the flow control behavior depends on the state of this bit:
+ * - If PORT_FORCE_FLOW_CTRL is set to 1, the switch will ignore AN results and
+ *   force flow control on the port.
+ * - If PORT_FORCE_FLOW_CTRL is set to 0, the switch will enable or disable
+ *   flow control based on the AN results.
+ *
+ * However, there is a potential limitation in this configuration. It is
+ * currently not possible to force disable flow control on a port if we still
+ * advertise pause support. While such a configuration is not currently
+ * supported by Linux, and may not make practical sense, it's important to be
+ * aware of this limitation when working with the KSZ8873 and similar devices.
+ */
+static void ksz8_phy_port_link_up(struct ksz_device *dev, int port, int duplex,
+				  bool tx_pause, bool rx_pause)
+{
+	const u16 *regs = dev->info->regs;
+	u8 sctrl = 0;
+
+	/* The KSZ8795 switch differs from the KSZ8873 by supporting
+	 * asymmetric pause control. However, since a single bit is used to
+	 * control both RX and TX pause, we can't enforce asymmetric pause
+	 * control - both TX and RX pause will be either enabled or disabled
+	 * together.
+	 *
+	 * If auto-negotiation is enabled, we usually allow the flow control to
+	 * be determined by the auto-negotiation process based on the
+	 * capabilities of both link partners. However, for KSZ8873, the
+	 * PORT_FORCE_FLOW_CTRL bit may be set by the hardware bootstrap,
+	 * ignoring the auto-negotiation result. Thus, even in auto-negotiation
+	 * mode, we need to ensure that the PORT_FORCE_FLOW_CTRL bit is
+	 * properly cleared.
+	 *
+	 * In the absence of pause auto-negotiation, we will enforce symmetric
+	 * pause control for both variants of switches - KSZ8873 and KSZ8795.
+	 *
+	 * Autoneg Pause Autoneg      rx,tx	PORT_FORCE_FLOW_CTRL
+	 * 1		1		x	0
+	 * 0		1		x	0 (flow control probably disabled)
+	 * x		0		1	1 (flow control force enabled)
+	 * 1		0		0	0 (flow control still depends on
+	 *					   aneg result due to hardware)
+	 * 0		0		0	0 (flow control probably disabled)
+	 */
+	if (dev->ports[port].manual_flow && tx_pause)
+		sctrl |= PORT_FORCE_FLOW_CTRL;
+
+	ksz_prmw8(dev, port, regs[P_STP_CTRL], PORT_FORCE_FLOW_CTRL, sctrl);
+}
+
+/**
+ * ksz8_cpu_port_link_up - Configures the CPU port of the switch.
+ * @dev: The KSZ device instance.
+ * @speed: The desired link speed.
+ * @duplex: The desired duplex mode.
+ * @tx_pause: If true, enables transmit pause.
+ * @rx_pause: If true, enables receive pause.
+ *
+ * Description:
+ * The function configures flow control and speed settings for the CPU
+ * port of the switch based on the desired settings, current duplex mode, and
+ * speed.
+ */
+static void ksz8_cpu_port_link_up(struct ksz_device *dev, int speed, int duplex,
+				  bool tx_pause, bool rx_pause)
+{
+	const u16 *regs = dev->info->regs;
+	u8 ctrl = 0;
+
+	/* SW_FLOW_CTRL, SW_HALF_DUPLEX, and SW_10_MBIT bits are bootstrappable
+	 * at least on KSZ8873. They can have different values depending on your
+	 * board setup.
+	 */
+	if (tx_pause || rx_pause)
+		ctrl |= SW_FLOW_CTRL;
+
+	if (duplex == DUPLEX_HALF)
+		ctrl |= SW_HALF_DUPLEX;
+
+	/* This hardware only supports SPEED_10 and SPEED_100. For SPEED_10
+	 * we need to set the SW_10_MBIT bit. Otherwise, we can leave it 0.
+	 */
+	if (speed == SPEED_10)
+		ctrl |= SW_10_MBIT;
+
+	ksz_rmw8(dev, regs[S_BROADCAST_CTRL], SW_HALF_DUPLEX | SW_FLOW_CTRL |
+		 SW_10_MBIT, ctrl);
+}
+
+void ksz8_phylink_mac_link_up(struct ksz_device *dev, int port,
+			      unsigned int mode, phy_interface_t interface,
+			      struct phy_device *phydev, int speed, int duplex,
+			      bool tx_pause, bool rx_pause)
+{
+	/* If the port is the CPU port, apply special handling. Only the CPU
+	 * port is configured via global registers.
+	 */
+	if (dev->cpu_port == port)
+		ksz8_cpu_port_link_up(dev, speed, duplex, tx_pause, rx_pause);
+	else if (dev->info->internal_phy[port])
+		ksz8_phy_port_link_up(dev, port, duplex, tx_pause, rx_pause);
+}
+
 static int ksz8_handle_global_errata(struct dsa_switch *ds)
 {
 	struct ksz_device *dev = ds->priv;
@@ -1487,8 +1625,6 @@ int ksz8_setup(struct dsa_switch *ds)
 	 */
 	ds->vlan_filtering_is_global = true;
 
-	ksz_cfg(dev, S_REPLACE_VID_CTRL, SW_FLOW_CTRL, true);
-
 	/* Enable automatic fast aging when link changed detected. */
 	ksz_cfg(dev, S_LINK_AGING_CTRL, SW_LINK_AUTO_AGING, true);
 
diff --git a/drivers/net/dsa/microchip/ksz8795_reg.h b/drivers/net/dsa/microchip/ksz8795_reg.h
index 3c9dae53e4..beca974e01 100644
--- a/drivers/net/dsa/microchip/ksz8795_reg.h
+++ b/drivers/net/dsa/microchip/ksz8795_reg.h
@@ -22,6 +22,9 @@
 #define KSZ8863_GLOBAL_SOFTWARE_RESET	BIT(4)
 #define KSZ8863_PCS_RESET		BIT(0)
 
+#define KSZ88X3_REG_FVID_AND_HOST_MODE  0xC6
+#define KSZ88X3_PORT3_RMII_CLK_INTERNAL BIT(3)
+
 #define REG_SW_CTRL_0			0x02
 
 #define SW_NEW_BACKOFF			BIT(7)
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index d5d7e48b7b..25a49708f4 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -277,6 +277,7 @@ static const struct ksz_dev_ops ksz8_dev_ops = {
 	.mirror_add = ksz8_port_mirror_add,
 	.mirror_del = ksz8_port_mirror_del,
 	.get_caps = ksz8_get_caps,
+	.phylink_mac_link_up = ksz8_phylink_mac_link_up,
 	.config_cpu_port = ksz8_config_cpu_port,
 	.enable_stp_addr = ksz8_enable_stp_addr,
 	.reset = ksz8_reset_switch,
@@ -1672,15 +1673,23 @@ static const struct ksz_chip_data *ksz_lookup_info(unsigned int prod_num)
 
 static int ksz_check_device_id(struct ksz_device *dev)
 {
-	const struct ksz_chip_data *dt_chip_data;
+	const struct ksz_chip_data *expected_chip_data;
+	u32 expected_chip_id;
 
-	dt_chip_data = of_device_get_match_data(dev->dev);
+	if (dev->pdata) {
+		expected_chip_id = dev->pdata->chip_id;
+		expected_chip_data = ksz_lookup_info(expected_chip_id);
+		if (WARN_ON(!expected_chip_data))
+			return -ENODEV;
+	} else {
+		expected_chip_data = of_device_get_match_data(dev->dev);
+		expected_chip_id = expected_chip_data->chip_id;
+	}
 
-	/* Check for Device Tree and Chip ID */
-	if (dt_chip_data->chip_id != dev->chip_id) {
+	if (expected_chip_id != dev->chip_id) {
 		dev_err(dev->dev,
 			"Device tree specifies chip %s but found %s, please fix it!\n",
-			dt_chip_data->dev_name, dev->info->dev_name);
+			expected_chip_data->dev_name, dev->info->dev_name);
 		return -ENODEV;
 	}
 
@@ -2709,7 +2718,7 @@ static enum dsa_tag_protocol ksz_get_tag_protocol(struct dsa_switch *ds,
 		proto = DSA_TAG_PROTO_KSZ9477;
 
 	if (is_lan937x(dev))
-		proto = DSA_TAG_PROTO_LAN937X_VALUE;
+		proto = DSA_TAG_PROTO_LAN937X;
 
 	return proto;
 }
@@ -2980,8 +2989,10 @@ static void ksz_phylink_mac_config(struct dsa_switch *ds, int port,
 {
 	struct ksz_device *dev = ds->priv;
 
-	if (ksz_is_ksz88x3(dev))
+	if (ksz_is_ksz88x3(dev)) {
+		dev->ports[port].manual_flow = !(state->pause & MLO_PAUSE_AN);
 		return;
+	}
 
 	/* Internal PHYs */
 	if (dev->info->internal_phy[port])
@@ -3124,10 +3135,8 @@ static void ksz_phylink_mac_link_up(struct dsa_switch *ds, int port,
 {
 	struct ksz_device *dev = ds->priv;
 
-	if (dev->dev_ops->phylink_mac_link_up)
-		dev->dev_ops->phylink_mac_link_up(dev, port, mode, interface,
-						  phydev, speed, duplex,
-						  tx_pause, rx_pause);
+	dev->dev_ops->phylink_mac_link_up(dev, port, mode, interface, phydev,
+					  speed, duplex, tx_pause, rx_pause);
 }
 
 static int ksz_switch_detect(struct ksz_device *dev)
@@ -4169,9 +4178,6 @@ int ksz_switch_register(struct ksz_device *dev)
 	int ret;
 	int i;
 
-	if (dev->pdata)
-		dev->chip_id = dev->pdata->chip_id;
-
 	dev->reset_gpio = devm_gpiod_get_optional(dev->dev, "reset",
 						  GPIOD_OUT_LOW);
 	if (IS_ERR(dev->reset_gpio))
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index b7e8a403a1..15612101a1 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -14,6 +14,7 @@
 #include <linux/regmap.h>
 #include <net/dsa.h>
 #include <linux/irq.h>
+#include <linux/platform_data/microchip-ksz.h>
 
 #include "ksz_ptp.h"
 
@@ -134,6 +135,7 @@ struct ksz_port {
 	ktime_t tstamp_msg;
 	struct completion tstamp_msg_comp;
 #endif
+	bool manual_flow;
 };
 
 struct ksz_device {
@@ -202,25 +204,6 @@ enum ksz_model {
 	LAN9374,
 };
 
-enum ksz_chip_id {
-	KSZ8563_CHIP_ID = 0x8563,
-	KSZ8795_CHIP_ID = 0x8795,
-	KSZ8794_CHIP_ID = 0x8794,
-	KSZ8765_CHIP_ID = 0x8765,
-	KSZ8830_CHIP_ID = 0x8830,
-	KSZ9477_CHIP_ID = 0x00947700,
-	KSZ9896_CHIP_ID = 0x00989600,
-	KSZ9897_CHIP_ID = 0x00989700,
-	KSZ9893_CHIP_ID = 0x00989300,
-	KSZ9563_CHIP_ID = 0x00956300,
-	KSZ9567_CHIP_ID = 0x00956700,
-	LAN9370_CHIP_ID = 0x00937000,
-	LAN9371_CHIP_ID = 0x00937100,
-	LAN9372_CHIP_ID = 0x00937200,
-	LAN9373_CHIP_ID = 0x00937300,
-	LAN9374_CHIP_ID = 0x00937400,
-};
-
 enum ksz_regs {
 	REG_SW_MAC_ADDR,
 	REG_IND_CTRL_0,