Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 163 insertions, 0 deletions

diff --git a/drivers/net/hamradio/Kconfig b/drivers/net/hamradio/Kconfig
new file mode 100644
index 0000000000..a94c7bd5db
--- /dev/null
+++ b/drivers/net/hamradio/Kconfig
@@ -0,0 +1,163 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config MKISS
+	tristate "Serial port KISS driver"
+	depends on AX25 && TTY
+	select CRC16
+	help
+	  KISS is a protocol used for the exchange of data between a computer
+	  and a Terminal Node Controller (a small embedded system commonly
+	  used for networking over AX.25 amateur radio connections; it
+	  connects the computer's serial port with the radio's microphone
+	  input and speaker output).
+
+	  Although KISS is less advanced than the 6pack protocol, it has
+	  the advantage that it is already supported by most modern TNCs
+	  without the need for a firmware upgrade.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called mkiss.
+
+config 6PACK
+	tristate "Serial port 6PACK driver"
+	depends on AX25 && TTY
+	help
+	  6pack is a transmission protocol for the data exchange between your
+	  PC and your TNC (the Terminal Node Controller acts as a kind of
+	  modem connecting your computer's serial port to your radio's
+	  microphone input and speaker output). This protocol can be used as
+	  an alternative to KISS for networking over AX.25 amateur radio
+	  connections, but it has some extended functionality.
+
+	  Note that this driver is still experimental and might cause
+	  problems. For details about the features and the usage of the
+	  driver, read <file:Documentation/networking/6pack.rst>.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called 6pack.
+
+config BPQETHER
+	tristate "BPQ Ethernet driver"
+	depends on AX25
+	help
+	  AX.25 is the protocol used for computer communication over amateur
+	  radio. If you say Y here, you will be able to send and receive AX.25
+	  traffic over Ethernet (also called "BPQ AX.25"), which could be
+	  useful if some other computer on your local network has a direct
+	  amateur radio connection.
+
+config SCC
+	tristate "Z8530 SCC driver"
+	depends on ISA && AX25
+	help
+	  These cards are used to connect your Linux box to an amateur radio
+	  in order to communicate with other computers. If you want to use
+	  this, read
+	  <file:Documentation/networking/device_drivers/hamradio/z8530drv.rst>
+	  and the AX25-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>. Also make sure to say Y
+	  to "Amateur Radio AX.25 Level 2" support.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called scc.
+
+config SCC_DELAY
+	bool "additional delay for PA0HZP OptoSCC compatible boards"
+	depends on SCC
+	help
+	  Say Y here if you experience problems with the SCC driver not
+	  working properly; please read
+	  <file:Documentation/networking/device_drivers/hamradio/z8530drv.rst>
+	  for details.
+
+	  If unsure, say N.
+
+config SCC_TRXECHO
+	bool "support for TRX that feedback the tx signal to rx"
+	depends on SCC
+	help
+	  Some transmitters feed the transmitted signal back to the receive
+	  line.  Say Y here to foil this by explicitly disabling the receiver
+	  during data transmission.
+
+	  If in doubt, say Y.
+
+config BAYCOM_SER_FDX
+	tristate "BAYCOM ser12 fullduplex driver for AX.25"
+	depends on AX25 && !S390
+	select CRC_CCITT
+	help
+	  This is one of two drivers for Baycom style simple amateur radio
+	  modems that connect to a serial interface. The driver supports the
+	  ser12 design in full-duplex mode. In addition, it allows the
+	  baudrate to be set between 300 and 4800 baud (however not all modems
+	  support all baudrates). This is the preferred driver. The next
+	  driver, "BAYCOM ser12 half-duplex driver for AX.25" is the old
+	  driver and still provided in case this driver does not work with
+	  your serial interface chip. To configure the driver, use the sethdlc
+	  utility available in the standard ax25 utilities package. For
+	  information on the modems, see <http://www.baycom.de/> and
+	  <file:Documentation/networking/device_drivers/hamradio/baycom.rst>.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called baycom_ser_fdx.  This is recommended.
+
+config BAYCOM_SER_HDX
+	tristate "BAYCOM ser12 halfduplex driver for AX.25"
+	depends on AX25 && !S390
+	select CRC_CCITT
+	help
+	  This is one of two drivers for Baycom style simple amateur radio
+	  modems that connect to a serial interface. The driver supports the
+	  ser12 design in half-duplex mode. This is the old driver.  It is
+	  still provided in case your serial interface chip does not work with
+	  the full-duplex driver. This driver is deprecated.  To configure
+	  the driver, use the sethdlc utility available in the standard ax25
+	  utilities package. For information on the modems, see
+	  <http://www.baycom.de/> and
+	  <file:Documentation/networking/device_drivers/hamradio/baycom.rst>.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called baycom_ser_hdx.  This is recommended.
+
+config BAYCOM_PAR
+	tristate "BAYCOM picpar and par96 driver for AX.25"
+	depends on PARPORT && AX25
+	select CRC_CCITT
+	help
+	  This is a driver for Baycom style simple amateur radio modems that
+	  connect to a parallel interface. The driver supports the picpar and
+	  par96 designs. To configure the driver, use the sethdlc utility
+	  available in the standard ax25 utilities package. For information on
+	  the modems, see <http://www.baycom.de/> and the file
+	  <file:Documentation/networking/device_drivers/hamradio/baycom.rst>.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called baycom_par.  This is recommended.
+
+config BAYCOM_EPP
+	tristate "BAYCOM epp driver for AX.25"
+	depends on PARPORT && AX25 && !64BIT
+	select CRC_CCITT
+	help
+	  This is a driver for Baycom style simple amateur radio modems that
+	  connect to a parallel interface. The driver supports the EPP
+	  designs. To configure the driver, use the sethdlc utility available
+	  in the standard ax25 utilities package. For information on the
+	  modems, see <http://www.baycom.de/> and the file
+	  <file:Documentation/networking/device_drivers/hamradio/baycom.rst>.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called baycom_epp.  This is recommended.
+
+config YAM
+	tristate "YAM driver for AX.25"
+	depends on AX25 && !S390
+	help
+	  The YAM is a modem for packet radio which connects to the serial
+	  port and includes some of the functions of a Terminal Node
+	  Controller. If you have one of those, say Y here.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called yam.
+
+