Adding upstream version 6.8.9.upstream/6.8.9

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 188 insertions, 0 deletions

diff --git a/drivers/net/phy/dp83tg720.c b/drivers/net/phy/dp83tg720.c
new file mode 100644
index 0000000000..326c9770a6
--- /dev/null
+++ b/drivers/net/phy/dp83tg720.c
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Driver for the Texas Instruments DP83TG720 PHY
+ * Copyright (c) 2023 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
+ */
+#include <linux/bitfield.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/phy.h>
+
+#define DP83TG720S_PHY_ID			0x2000a284
+
+/* MDIO_MMD_VEND2 registers */
+#define DP83TG720S_MII_REG_10			0x10
+#define DP83TG720S_STS_MII_INT			BIT(7)
+#define DP83TG720S_LINK_STATUS			BIT(0)
+
+#define DP83TG720S_PHY_RESET			0x1f
+#define DP83TG720S_HW_RESET			BIT(15)
+
+#define DP83TG720S_RGMII_DELAY_CTRL		0x602
+/* In RGMII mode, Enable or disable the internal delay for RXD */
+#define DP83TG720S_RGMII_RX_CLK_SEL		BIT(1)
+/* In RGMII mode, Enable or disable the internal delay for TXD */
+#define DP83TG720S_RGMII_TX_CLK_SEL		BIT(0)
+
+#define DP83TG720S_SQI_REG_1			0x871
+#define DP83TG720S_SQI_OUT_WORST		GENMASK(7, 5)
+#define DP83TG720S_SQI_OUT			GENMASK(3, 1)
+
+#define DP83TG720_SQI_MAX			7
+
+static int dp83tg720_config_aneg(struct phy_device *phydev)
+{
+	/* Autoneg is not supported and this PHY supports only one speed.
+	 * We need to care only about master/slave configuration if it was
+	 * changed by user.
+	 */
+	return genphy_c45_pma_baset1_setup_master_slave(phydev);
+}
+
+static int dp83tg720_read_status(struct phy_device *phydev)
+{
+	u16 phy_sts;
+	int ret;
+
+	phydev->pause = 0;
+	phydev->asym_pause = 0;
+
+	/* Most of Clause 45 registers are not present, so we can't use
+	 * genphy_c45_read_status() here.
+	 */
+	phy_sts = phy_read(phydev, DP83TG720S_MII_REG_10);
+	phydev->link = !!(phy_sts & DP83TG720S_LINK_STATUS);
+	if (!phydev->link) {
+		/* According to the "DP83TC81x, DP83TG72x Software
+		 * Implementation Guide", the PHY needs to be reset after a
+		 * link loss or if no link is created after at least 100ms.
+		 *
+		 * Currently we are polling with the PHY_STATE_TIME (1000ms)
+		 * interval, which is still enough for not automotive use cases.
+		 */
+		ret = phy_init_hw(phydev);
+		if (ret)
+			return ret;
+
+		/* After HW reset we need to restore master/slave configuration.
+		 */
+		ret = dp83tg720_config_aneg(phydev);
+		if (ret)
+			return ret;
+
+		phydev->speed = SPEED_UNKNOWN;
+		phydev->duplex = DUPLEX_UNKNOWN;
+	} else {
+		/* PMA/PMD control 1 register (Register 1.0) is present, but it
+		 * doesn't contain the link speed information.
+		 * So genphy_c45_read_pma() can't be used here.
+		 */
+		ret = genphy_c45_pma_baset1_read_master_slave(phydev);
+		if (ret)
+			return ret;
+
+		phydev->duplex = DUPLEX_FULL;
+		phydev->speed = SPEED_1000;
+	}
+
+	return 0;
+}
+
+static int dp83tg720_get_sqi(struct phy_device *phydev)
+{
+	int ret;
+
+	if (!phydev->link)
+		return 0;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, DP83TG720S_SQI_REG_1);
+	if (ret < 0)
+		return ret;
+
+	return FIELD_GET(DP83TG720S_SQI_OUT, ret);
+}
+
+static int dp83tg720_get_sqi_max(struct phy_device *phydev)
+{
+	return DP83TG720_SQI_MAX;
+}
+
+static int dp83tg720_config_rgmii_delay(struct phy_device *phydev)
+{
+	u16 rgmii_delay_mask;
+	u16 rgmii_delay = 0;
+
+	switch (phydev->interface) {
+	case PHY_INTERFACE_MODE_RGMII:
+		rgmii_delay = 0;
+		break;
+	case PHY_INTERFACE_MODE_RGMII_ID:
+		rgmii_delay = DP83TG720S_RGMII_RX_CLK_SEL |
+				DP83TG720S_RGMII_TX_CLK_SEL;
+		break;
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+		rgmii_delay = DP83TG720S_RGMII_RX_CLK_SEL;
+		break;
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		rgmii_delay = DP83TG720S_RGMII_TX_CLK_SEL;
+		break;
+	default:
+		return 0;
+	}
+
+	rgmii_delay_mask = DP83TG720S_RGMII_RX_CLK_SEL |
+		DP83TG720S_RGMII_TX_CLK_SEL;
+
+	return phy_modify_mmd(phydev, MDIO_MMD_VEND2,
+			      DP83TG720S_RGMII_DELAY_CTRL, rgmii_delay_mask,
+			      rgmii_delay);
+}
+
+static int dp83tg720_config_init(struct phy_device *phydev)
+{
+	int ret;
+
+	/* Software Restart is not enough to recover from a link failure.
+	 * Using Hardware Reset instead.
+	 */
+	ret = phy_write(phydev, DP83TG720S_PHY_RESET, DP83TG720S_HW_RESET);
+	if (ret)
+		return ret;
+
+	/* Wait until MDC can be used again.
+	 * The wait value of one 1ms is documented in "DP83TG720S-Q1 1000BASE-T1
+	 * Automotive Ethernet PHY with SGMII and RGMII" datasheet.
+	 */
+	usleep_range(1000, 2000);
+
+	if (phy_interface_is_rgmii(phydev))
+		return dp83tg720_config_rgmii_delay(phydev);
+
+	return 0;
+}
+
+static struct phy_driver dp83tg720_driver[] = {
+{
+	PHY_ID_MATCH_MODEL(DP83TG720S_PHY_ID),
+	.name		= "TI DP83TG720S",
+
+	.config_aneg	= dp83tg720_config_aneg,
+	.read_status	= dp83tg720_read_status,
+	.get_features	= genphy_c45_pma_read_ext_abilities,
+	.config_init	= dp83tg720_config_init,
+	.get_sqi	= dp83tg720_get_sqi,
+	.get_sqi_max	= dp83tg720_get_sqi_max,
+
+	.suspend	= genphy_suspend,
+	.resume		= genphy_resume,
+} };
+module_phy_driver(dp83tg720_driver);
+
+static struct mdio_device_id __maybe_unused dp83tg720_tbl[] = {
+	{ PHY_ID_MATCH_MODEL(DP83TG720S_PHY_ID) },
+	{ }
+};
+MODULE_DEVICE_TABLE(mdio, dp83tg720_tbl);
+
+MODULE_DESCRIPTION("Texas Instruments DP83TG720S PHY driver");
+MODULE_AUTHOR("Oleksij Rempel <kernel@pengutronix.de>");
+MODULE_LICENSE("GPL");