Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 878 insertions, 0 deletions

diff --git a/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c b/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c
new file mode 100644
index 0000000000..e0d43d076c
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c
@@ -0,0 +1,878 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2015, Sony Mobile Communications AB.
+ * Copyright (c) 2013, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/gpio/driver.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/seq_file.h>
+#include <linux/slab.h>
+
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "../core.h"
+#include "../pinctrl-utils.h"
+
+/* mode */
+#define PM8XXX_GPIO_MODE_ENABLED	BIT(0)
+#define PM8XXX_GPIO_MODE_INPUT		0
+#define PM8XXX_GPIO_MODE_OUTPUT		2
+
+/* output buffer */
+#define PM8XXX_GPIO_PUSH_PULL		0
+#define PM8XXX_GPIO_OPEN_DRAIN		1
+
+/* bias */
+#define PM8XXX_GPIO_BIAS_PU_30		0
+#define PM8XXX_GPIO_BIAS_PU_1P5		1
+#define PM8XXX_GPIO_BIAS_PU_31P5	2
+#define PM8XXX_GPIO_BIAS_PU_1P5_30	3
+#define PM8XXX_GPIO_BIAS_PD		4
+#define PM8XXX_GPIO_BIAS_NP		5
+
+/* GPIO registers */
+#define SSBI_REG_ADDR_GPIO_BASE		0x150
+#define SSBI_REG_ADDR_GPIO(n)		(SSBI_REG_ADDR_GPIO_BASE + n)
+
+#define PM8XXX_BANK_WRITE		BIT(7)
+
+#define PM8XXX_MAX_GPIOS               44
+
+#define PM8XXX_GPIO_PHYSICAL_OFFSET	1
+
+/* custom pinconf parameters */
+#define PM8XXX_QCOM_DRIVE_STRENGH      (PIN_CONFIG_END + 1)
+#define PM8XXX_QCOM_PULL_UP_STRENGTH   (PIN_CONFIG_END + 2)
+
+/**
+ * struct pm8xxx_pin_data - dynamic configuration for a pin
+ * @reg:               address of the control register
+ * @power_source:      logical selected voltage source, mapping in static data
+ *                     is used translate to register values
+ * @mode:              operating mode for the pin (input/output)
+ * @open_drain:        output buffer configured as open-drain (vs push-pull)
+ * @output_value:      configured output value
+ * @bias:              register view of configured bias
+ * @pull_up_strength:  placeholder for selected pull up strength
+ *                     only used to configure bias when pull up is selected
+ * @output_strength:   selector of output-strength
+ * @disable:           pin disabled / configured as tristate
+ * @function:          pinmux selector
+ * @inverted:          pin logic is inverted
+ */
+struct pm8xxx_pin_data {
+	unsigned reg;
+	u8 power_source;
+	u8 mode;
+	bool open_drain;
+	bool output_value;
+	u8 bias;
+	u8 pull_up_strength;
+	u8 output_strength;
+	bool disable;
+	u8 function;
+	bool inverted;
+};
+
+struct pm8xxx_gpio {
+	struct device *dev;
+	struct regmap *regmap;
+	struct pinctrl_dev *pctrl;
+	struct gpio_chip chip;
+
+	struct pinctrl_desc desc;
+	unsigned npins;
+};
+
+static const struct pinconf_generic_params pm8xxx_gpio_bindings[] = {
+	{"qcom,drive-strength",		PM8XXX_QCOM_DRIVE_STRENGH,	0},
+	{"qcom,pull-up-strength",	PM8XXX_QCOM_PULL_UP_STRENGTH,	0},
+};
+
+#ifdef CONFIG_DEBUG_FS
+static const struct pin_config_item pm8xxx_conf_items[ARRAY_SIZE(pm8xxx_gpio_bindings)] = {
+	PCONFDUMP(PM8XXX_QCOM_DRIVE_STRENGH, "drive-strength", NULL, true),
+	PCONFDUMP(PM8XXX_QCOM_PULL_UP_STRENGTH,  "pull up strength", NULL, true),
+};
+#endif
+
+static const char * const pm8xxx_groups[PM8XXX_MAX_GPIOS] = {
+	"gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8",
+	"gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15",
+	"gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21", "gpio22",
+	"gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28", "gpio29",
+	"gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35", "gpio36",
+	"gpio37", "gpio38", "gpio39", "gpio40", "gpio41", "gpio42", "gpio43",
+	"gpio44",
+};
+
+static const char * const pm8xxx_gpio_functions[] = {
+	PMIC_GPIO_FUNC_NORMAL, PMIC_GPIO_FUNC_PAIRED,
+	PMIC_GPIO_FUNC_FUNC1, PMIC_GPIO_FUNC_FUNC2,
+	PMIC_GPIO_FUNC_DTEST1, PMIC_GPIO_FUNC_DTEST2,
+	PMIC_GPIO_FUNC_DTEST3, PMIC_GPIO_FUNC_DTEST4,
+};
+
+static int pm8xxx_read_bank(struct pm8xxx_gpio *pctrl,
+			    struct pm8xxx_pin_data *pin, int bank)
+{
+	unsigned int val = bank << 4;
+	int ret;
+
+	ret = regmap_write(pctrl->regmap, pin->reg, val);
+	if (ret) {
+		dev_err(pctrl->dev, "failed to select bank %d\n", bank);
+		return ret;
+	}
+
+	ret = regmap_read(pctrl->regmap, pin->reg, &val);
+	if (ret) {
+		dev_err(pctrl->dev, "failed to read register %d\n", bank);
+		return ret;
+	}
+
+	return val;
+}
+
+static int pm8xxx_write_bank(struct pm8xxx_gpio *pctrl,
+			     struct pm8xxx_pin_data *pin,
+			     int bank,
+			     u8 val)
+{
+	int ret;
+
+	val |= PM8XXX_BANK_WRITE;
+	val |= bank << 4;
+
+	ret = regmap_write(pctrl->regmap, pin->reg, val);
+	if (ret)
+		dev_err(pctrl->dev, "failed to write register\n");
+
+	return ret;
+}
+
+static int pm8xxx_get_groups_count(struct pinctrl_dev *pctldev)
+{
+	struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+	return pctrl->npins;
+}
+
+static const char *pm8xxx_get_group_name(struct pinctrl_dev *pctldev,
+					 unsigned group)
+{
+	return pm8xxx_groups[group];
+}
+
+
+static int pm8xxx_get_group_pins(struct pinctrl_dev *pctldev,
+				 unsigned group,
+				 const unsigned **pins,
+				 unsigned *num_pins)
+{
+	struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+	*pins = &pctrl->desc.pins[group].number;
+	*num_pins = 1;
+
+	return 0;
+}
+
+static const struct pinctrl_ops pm8xxx_pinctrl_ops = {
+	.get_groups_count	= pm8xxx_get_groups_count,
+	.get_group_name		= pm8xxx_get_group_name,
+	.get_group_pins         = pm8xxx_get_group_pins,
+	.dt_node_to_map		= pinconf_generic_dt_node_to_map_group,
+	.dt_free_map		= pinctrl_utils_free_map,
+};
+
+static int pm8xxx_get_functions_count(struct pinctrl_dev *pctldev)
+{
+	return ARRAY_SIZE(pm8xxx_gpio_functions);
+}
+
+static const char *pm8xxx_get_function_name(struct pinctrl_dev *pctldev,
+					    unsigned function)
+{
+	return pm8xxx_gpio_functions[function];
+}
+
+static int pm8xxx_get_function_groups(struct pinctrl_dev *pctldev,
+				      unsigned function,
+				      const char * const **groups,
+				      unsigned * const num_groups)
+{
+	struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+	*groups = pm8xxx_groups;
+	*num_groups = pctrl->npins;
+	return 0;
+}
+
+static int pm8xxx_pinmux_set_mux(struct pinctrl_dev *pctldev,
+				 unsigned function,
+				 unsigned group)
+{
+	struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	struct pm8xxx_pin_data *pin = pctrl->desc.pins[group].drv_data;
+	u8 val;
+
+	pin->function = function;
+	val = pin->function << 1;
+
+	pm8xxx_write_bank(pctrl, pin, 4, val);
+
+	return 0;
+}
+
+static const struct pinmux_ops pm8xxx_pinmux_ops = {
+	.get_functions_count	= pm8xxx_get_functions_count,
+	.get_function_name	= pm8xxx_get_function_name,
+	.get_function_groups	= pm8xxx_get_function_groups,
+	.set_mux		= pm8xxx_pinmux_set_mux,
+};
+
+static int pm8xxx_pin_config_get(struct pinctrl_dev *pctldev,
+				 unsigned int offset,
+				 unsigned long *config)
+{
+	struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+	unsigned param = pinconf_to_config_param(*config);
+	unsigned arg;
+
+	switch (param) {
+	case PIN_CONFIG_BIAS_DISABLE:
+		if (pin->bias != PM8XXX_GPIO_BIAS_NP)
+			return -EINVAL;
+		arg = 1;
+		break;
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		if (pin->bias != PM8XXX_GPIO_BIAS_PD)
+			return -EINVAL;
+		arg = 1;
+		break;
+	case PIN_CONFIG_BIAS_PULL_UP:
+		if (pin->bias > PM8XXX_GPIO_BIAS_PU_1P5_30)
+			return -EINVAL;
+		arg = 1;
+		break;
+	case PM8XXX_QCOM_PULL_UP_STRENGTH:
+		arg = pin->pull_up_strength;
+		break;
+	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+		if (!pin->disable)
+			return -EINVAL;
+		arg = 1;
+		break;
+	case PIN_CONFIG_INPUT_ENABLE:
+		if (pin->mode != PM8XXX_GPIO_MODE_INPUT)
+			return -EINVAL;
+		arg = 1;
+		break;
+	case PIN_CONFIG_OUTPUT:
+		if (pin->mode & PM8XXX_GPIO_MODE_OUTPUT)
+			arg = pin->output_value;
+		else
+			arg = 0;
+		break;
+	case PIN_CONFIG_POWER_SOURCE:
+		arg = pin->power_source;
+		break;
+	case PM8XXX_QCOM_DRIVE_STRENGH:
+		arg = pin->output_strength;
+		break;
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+		if (pin->open_drain)
+			return -EINVAL;
+		arg = 1;
+		break;
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+		if (!pin->open_drain)
+			return -EINVAL;
+		arg = 1;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	*config = pinconf_to_config_packed(param, arg);
+
+	return 0;
+}
+
+static int pm8xxx_pin_config_set(struct pinctrl_dev *pctldev,
+				 unsigned int offset,
+				 unsigned long *configs,
+				 unsigned num_configs)
+{
+	struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+	unsigned param;
+	unsigned arg;
+	unsigned i;
+	u8 banks = 0;
+	u8 val;
+
+	for (i = 0; i < num_configs; i++) {
+		param = pinconf_to_config_param(configs[i]);
+		arg = pinconf_to_config_argument(configs[i]);
+
+		switch (param) {
+		case PIN_CONFIG_BIAS_DISABLE:
+			pin->bias = PM8XXX_GPIO_BIAS_NP;
+			banks |= BIT(2);
+			pin->disable = 0;
+			banks |= BIT(3);
+			break;
+		case PIN_CONFIG_BIAS_PULL_DOWN:
+			pin->bias = PM8XXX_GPIO_BIAS_PD;
+			banks |= BIT(2);
+			pin->disable = 0;
+			banks |= BIT(3);
+			break;
+		case PM8XXX_QCOM_PULL_UP_STRENGTH:
+			if (arg > PM8XXX_GPIO_BIAS_PU_1P5_30) {
+				dev_err(pctrl->dev, "invalid pull-up strength\n");
+				return -EINVAL;
+			}
+			pin->pull_up_strength = arg;
+			fallthrough;
+		case PIN_CONFIG_BIAS_PULL_UP:
+			pin->bias = pin->pull_up_strength;
+			banks |= BIT(2);
+			pin->disable = 0;
+			banks |= BIT(3);
+			break;
+		case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+			pin->disable = 1;
+			banks |= BIT(3);
+			break;
+		case PIN_CONFIG_INPUT_ENABLE:
+			pin->mode = PM8XXX_GPIO_MODE_INPUT;
+			banks |= BIT(0) | BIT(1);
+			break;
+		case PIN_CONFIG_OUTPUT:
+			pin->mode = PM8XXX_GPIO_MODE_OUTPUT;
+			pin->output_value = !!arg;
+			banks |= BIT(0) | BIT(1);
+			break;
+		case PIN_CONFIG_POWER_SOURCE:
+			pin->power_source = arg;
+			banks |= BIT(0);
+			break;
+		case PM8XXX_QCOM_DRIVE_STRENGH:
+			if (arg > PMIC_GPIO_STRENGTH_LOW) {
+				dev_err(pctrl->dev, "invalid drive strength\n");
+				return -EINVAL;
+			}
+			pin->output_strength = arg;
+			banks |= BIT(3);
+			break;
+		case PIN_CONFIG_DRIVE_PUSH_PULL:
+			pin->open_drain = 0;
+			banks |= BIT(1);
+			break;
+		case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+			pin->open_drain = 1;
+			banks |= BIT(1);
+			break;
+		default:
+			dev_err(pctrl->dev,
+				"unsupported config parameter: %x\n",
+				param);
+			return -EINVAL;
+		}
+	}
+
+	if (banks & BIT(0)) {
+		val = pin->power_source << 1;
+		val |= PM8XXX_GPIO_MODE_ENABLED;
+		pm8xxx_write_bank(pctrl, pin, 0, val);
+	}
+
+	if (banks & BIT(1)) {
+		val = pin->mode << 2;
+		val |= pin->open_drain << 1;
+		val |= pin->output_value;
+		pm8xxx_write_bank(pctrl, pin, 1, val);
+	}
+
+	if (banks & BIT(2)) {
+		val = pin->bias << 1;
+		pm8xxx_write_bank(pctrl, pin, 2, val);
+	}
+
+	if (banks & BIT(3)) {
+		val = pin->output_strength << 2;
+		val |= pin->disable;
+		pm8xxx_write_bank(pctrl, pin, 3, val);
+	}
+
+	if (banks & BIT(4)) {
+		val = pin->function << 1;
+		pm8xxx_write_bank(pctrl, pin, 4, val);
+	}
+
+	if (banks & BIT(5)) {
+		val = 0;
+		if (!pin->inverted)
+			val |= BIT(3);
+		pm8xxx_write_bank(pctrl, pin, 5, val);
+	}
+
+	return 0;
+}
+
+static const struct pinconf_ops pm8xxx_pinconf_ops = {
+	.is_generic = true,
+	.pin_config_group_get = pm8xxx_pin_config_get,
+	.pin_config_group_set = pm8xxx_pin_config_set,
+};
+
+static const struct pinctrl_desc pm8xxx_pinctrl_desc = {
+	.name = "pm8xxx_gpio",
+	.pctlops = &pm8xxx_pinctrl_ops,
+	.pmxops = &pm8xxx_pinmux_ops,
+	.confops = &pm8xxx_pinconf_ops,
+	.owner = THIS_MODULE,
+};
+
+static int pm8xxx_gpio_direction_input(struct gpio_chip *chip,
+				       unsigned offset)
+{
+	struct pm8xxx_gpio *pctrl = gpiochip_get_data(chip);
+	struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+	u8 val;
+
+	pin->mode = PM8XXX_GPIO_MODE_INPUT;
+	val = pin->mode << 2;
+
+	pm8xxx_write_bank(pctrl, pin, 1, val);
+
+	return 0;
+}
+
+static int pm8xxx_gpio_direction_output(struct gpio_chip *chip,
+					unsigned offset,
+					int value)
+{
+	struct pm8xxx_gpio *pctrl = gpiochip_get_data(chip);
+	struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+	u8 val;
+
+	pin->mode = PM8XXX_GPIO_MODE_OUTPUT;
+	pin->output_value = !!value;
+
+	val = pin->mode << 2;
+	val |= pin->open_drain << 1;
+	val |= pin->output_value;
+
+	pm8xxx_write_bank(pctrl, pin, 1, val);
+
+	return 0;
+}
+
+static int pm8xxx_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+	struct pm8xxx_gpio *pctrl = gpiochip_get_data(chip);
+	struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+	int ret, irq;
+	bool state;
+
+	if (pin->mode == PM8XXX_GPIO_MODE_OUTPUT)
+		return pin->output_value;
+
+	irq = chip->to_irq(chip, offset);
+	if (irq >= 0) {
+		ret = irq_get_irqchip_state(irq, IRQCHIP_STATE_LINE_LEVEL,
+					    &state);
+		if (!ret)
+			ret = !!state;
+	} else
+		ret = -EINVAL;
+
+	return ret;
+}
+
+static void pm8xxx_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	struct pm8xxx_gpio *pctrl = gpiochip_get_data(chip);
+	struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+	u8 val;
+
+	pin->output_value = !!value;
+
+	val = pin->mode << 2;
+	val |= pin->open_drain << 1;
+	val |= pin->output_value;
+
+	pm8xxx_write_bank(pctrl, pin, 1, val);
+}
+
+static int pm8xxx_gpio_of_xlate(struct gpio_chip *chip,
+				const struct of_phandle_args *gpio_desc,
+				u32 *flags)
+{
+	if (chip->of_gpio_n_cells < 2)
+		return -EINVAL;
+
+	if (flags)
+		*flags = gpio_desc->args[1];
+
+	return gpio_desc->args[0] - PM8XXX_GPIO_PHYSICAL_OFFSET;
+}
+
+
+#ifdef CONFIG_DEBUG_FS
+
+static void pm8xxx_gpio_dbg_show_one(struct seq_file *s,
+				  struct pinctrl_dev *pctldev,
+				  struct gpio_chip *chip,
+				  unsigned offset,
+				  unsigned gpio)
+{
+	struct pm8xxx_gpio *pctrl = gpiochip_get_data(chip);
+	struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data;
+
+	static const char * const modes[] = {
+		"in", "both", "out", "off"
+	};
+	static const char * const biases[] = {
+		"pull-up 30uA", "pull-up 1.5uA", "pull-up 31.5uA",
+		"pull-up 1.5uA + 30uA boost", "pull-down 10uA", "no pull"
+	};
+	static const char * const buffer_types[] = {
+		"push-pull", "open-drain"
+	};
+	static const char * const strengths[] = {
+		"no", "high", "medium", "low"
+	};
+
+	seq_printf(s, " gpio%-2d:", offset + PM8XXX_GPIO_PHYSICAL_OFFSET);
+	if (pin->disable) {
+		seq_puts(s, " ---");
+	} else {
+		seq_printf(s, " %-4s", modes[pin->mode]);
+		seq_printf(s, " %-7s", pm8xxx_gpio_functions[pin->function]);
+		seq_printf(s, " VIN%d", pin->power_source);
+		seq_printf(s, " %-27s", biases[pin->bias]);
+		seq_printf(s, " %-10s", buffer_types[pin->open_drain]);
+		seq_printf(s, " %-4s", pin->output_value ? "high" : "low");
+		seq_printf(s, " %-7s", strengths[pin->output_strength]);
+		if (pin->inverted)
+			seq_puts(s, " inverted");
+	}
+}
+
+static void pm8xxx_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+	unsigned gpio = chip->base;
+	unsigned i;
+
+	for (i = 0; i < chip->ngpio; i++, gpio++) {
+		pm8xxx_gpio_dbg_show_one(s, NULL, chip, i, gpio);
+		seq_puts(s, "\n");
+	}
+}
+
+#else
+#define pm8xxx_gpio_dbg_show NULL
+#endif
+
+static const struct gpio_chip pm8xxx_gpio_template = {
+	.direction_input = pm8xxx_gpio_direction_input,
+	.direction_output = pm8xxx_gpio_direction_output,
+	.get = pm8xxx_gpio_get,
+	.set = pm8xxx_gpio_set,
+	.of_xlate = pm8xxx_gpio_of_xlate,
+	.dbg_show = pm8xxx_gpio_dbg_show,
+	.owner = THIS_MODULE,
+};
+
+static int pm8xxx_pin_populate(struct pm8xxx_gpio *pctrl,
+			       struct pm8xxx_pin_data *pin)
+{
+	int val;
+
+	val = pm8xxx_read_bank(pctrl, pin, 0);
+	if (val < 0)
+		return val;
+
+	pin->power_source = (val >> 1) & 0x7;
+
+	val = pm8xxx_read_bank(pctrl, pin, 1);
+	if (val < 0)
+		return val;
+
+	pin->mode = (val >> 2) & 0x3;
+	pin->open_drain = !!(val & BIT(1));
+	pin->output_value = val & BIT(0);
+
+	val = pm8xxx_read_bank(pctrl, pin, 2);
+	if (val < 0)
+		return val;
+
+	pin->bias = (val >> 1) & 0x7;
+	if (pin->bias <= PM8XXX_GPIO_BIAS_PU_1P5_30)
+		pin->pull_up_strength = pin->bias;
+	else
+		pin->pull_up_strength = PM8XXX_GPIO_BIAS_PU_30;
+
+	val = pm8xxx_read_bank(pctrl, pin, 3);
+	if (val < 0)
+		return val;
+
+	pin->output_strength = (val >> 2) & 0x3;
+	pin->disable = val & BIT(0);
+
+	val = pm8xxx_read_bank(pctrl, pin, 4);
+	if (val < 0)
+		return val;
+
+	pin->function = (val >> 1) & 0x7;
+
+	val = pm8xxx_read_bank(pctrl, pin, 5);
+	if (val < 0)
+		return val;
+
+	pin->inverted = !(val & BIT(3));
+
+	return 0;
+}
+
+static void pm8xxx_irq_disable(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+
+	gpiochip_disable_irq(gc, irqd_to_hwirq(d));
+}
+
+static void pm8xxx_irq_enable(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+
+	gpiochip_enable_irq(gc, irqd_to_hwirq(d));
+}
+
+static const struct irq_chip pm8xxx_irq_chip = {
+	.name = "ssbi-gpio",
+	.irq_mask_ack = irq_chip_mask_ack_parent,
+	.irq_unmask = irq_chip_unmask_parent,
+	.irq_disable = pm8xxx_irq_disable,
+	.irq_enable = pm8xxx_irq_enable,
+	.irq_set_type = irq_chip_set_type_parent,
+	.flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE |
+		IRQCHIP_IMMUTABLE,
+	GPIOCHIP_IRQ_RESOURCE_HELPERS,
+};
+
+static int pm8xxx_domain_translate(struct irq_domain *domain,
+				   struct irq_fwspec *fwspec,
+				   unsigned long *hwirq,
+				   unsigned int *type)
+{
+	struct pm8xxx_gpio *pctrl = container_of(domain->host_data,
+						 struct pm8xxx_gpio, chip);
+
+	if (fwspec->param_count != 2 || fwspec->param[0] < 1 ||
+	    fwspec->param[0] > pctrl->chip.ngpio)
+		return -EINVAL;
+
+	*hwirq = fwspec->param[0] - PM8XXX_GPIO_PHYSICAL_OFFSET;
+	*type = fwspec->param[1];
+
+	return 0;
+}
+
+static unsigned int pm8xxx_child_offset_to_irq(struct gpio_chip *chip,
+					       unsigned int offset)
+{
+	return offset + PM8XXX_GPIO_PHYSICAL_OFFSET;
+}
+
+static int pm8xxx_child_to_parent_hwirq(struct gpio_chip *chip,
+					unsigned int child_hwirq,
+					unsigned int child_type,
+					unsigned int *parent_hwirq,
+					unsigned int *parent_type)
+{
+	*parent_hwirq = child_hwirq + 0xc0;
+	*parent_type = child_type;
+
+	return 0;
+}
+
+static const struct of_device_id pm8xxx_gpio_of_match[] = {
+	{ .compatible = "qcom,pm8018-gpio", .data = (void *) 6 },
+	{ .compatible = "qcom,pm8038-gpio", .data = (void *) 12 },
+	{ .compatible = "qcom,pm8058-gpio", .data = (void *) 44 },
+	{ .compatible = "qcom,pm8917-gpio", .data = (void *) 38 },
+	{ .compatible = "qcom,pm8921-gpio", .data = (void *) 44 },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, pm8xxx_gpio_of_match);
+
+static int pm8xxx_gpio_probe(struct platform_device *pdev)
+{
+	struct pm8xxx_pin_data *pin_data;
+	struct irq_domain *parent_domain;
+	struct device_node *parent_node;
+	struct pinctrl_pin_desc *pins;
+	struct gpio_irq_chip *girq;
+	struct pm8xxx_gpio *pctrl;
+	int ret, i;
+
+	pctrl = devm_kzalloc(&pdev->dev, sizeof(*pctrl), GFP_KERNEL);
+	if (!pctrl)
+		return -ENOMEM;
+
+	pctrl->dev = &pdev->dev;
+	pctrl->npins = (uintptr_t) device_get_match_data(&pdev->dev);
+
+	pctrl->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!pctrl->regmap) {
+		dev_err(&pdev->dev, "parent regmap unavailable\n");
+		return -ENXIO;
+	}
+
+	pctrl->desc = pm8xxx_pinctrl_desc;
+	pctrl->desc.npins = pctrl->npins;
+
+	pins = devm_kcalloc(&pdev->dev,
+			    pctrl->desc.npins,
+			    sizeof(struct pinctrl_pin_desc),
+			    GFP_KERNEL);
+	if (!pins)
+		return -ENOMEM;
+
+	pin_data = devm_kcalloc(&pdev->dev,
+				pctrl->desc.npins,
+				sizeof(struct pm8xxx_pin_data),
+				GFP_KERNEL);
+	if (!pin_data)
+		return -ENOMEM;
+
+	for (i = 0; i < pctrl->desc.npins; i++) {
+		pin_data[i].reg = SSBI_REG_ADDR_GPIO(i);
+
+		ret = pm8xxx_pin_populate(pctrl, &pin_data[i]);
+		if (ret)
+			return ret;
+
+		pins[i].number = i;
+		pins[i].name = pm8xxx_groups[i];
+		pins[i].drv_data = &pin_data[i];
+	}
+	pctrl->desc.pins = pins;
+
+	pctrl->desc.num_custom_params = ARRAY_SIZE(pm8xxx_gpio_bindings);
+	pctrl->desc.custom_params = pm8xxx_gpio_bindings;
+#ifdef CONFIG_DEBUG_FS
+	pctrl->desc.custom_conf_items = pm8xxx_conf_items;
+#endif
+
+	pctrl->pctrl = devm_pinctrl_register(&pdev->dev, &pctrl->desc, pctrl);
+	if (IS_ERR(pctrl->pctrl)) {
+		dev_err(&pdev->dev, "couldn't register pm8xxx gpio driver\n");
+		return PTR_ERR(pctrl->pctrl);
+	}
+
+	pctrl->chip = pm8xxx_gpio_template;
+	pctrl->chip.base = -1;
+	pctrl->chip.parent = &pdev->dev;
+	pctrl->chip.of_gpio_n_cells = 2;
+	pctrl->chip.label = dev_name(pctrl->dev);
+	pctrl->chip.ngpio = pctrl->npins;
+
+	parent_node = of_irq_find_parent(pctrl->dev->of_node);
+	if (!parent_node)
+		return -ENXIO;
+
+	parent_domain = irq_find_host(parent_node);
+	of_node_put(parent_node);
+	if (!parent_domain)
+		return -ENXIO;
+
+	girq = &pctrl->chip.irq;
+	gpio_irq_chip_set_chip(girq, &pm8xxx_irq_chip);
+	girq->default_type = IRQ_TYPE_NONE;
+	girq->handler = handle_level_irq;
+	girq->fwnode = dev_fwnode(pctrl->dev);
+	girq->parent_domain = parent_domain;
+	girq->child_to_parent_hwirq = pm8xxx_child_to_parent_hwirq;
+	girq->populate_parent_alloc_arg = gpiochip_populate_parent_fwspec_twocell;
+	girq->child_offset_to_irq = pm8xxx_child_offset_to_irq;
+	girq->child_irq_domain_ops.translate = pm8xxx_domain_translate;
+
+	ret = gpiochip_add_data(&pctrl->chip, pctrl);
+	if (ret) {
+		dev_err(&pdev->dev, "failed register gpiochip\n");
+		return ret;
+	}
+
+	/*
+	 * For DeviceTree-supported systems, the gpio core checks the
+	 * pinctrl's device node for the "gpio-ranges" property.
+	 * If it is present, it takes care of adding the pin ranges
+	 * for the driver. In this case the driver can skip ahead.
+	 *
+	 * In order to remain compatible with older, existing DeviceTree
+	 * files which don't set the "gpio-ranges" property or systems that
+	 * utilize ACPI the driver has to call gpiochip_add_pin_range().
+	 */
+	if (!of_property_read_bool(pctrl->dev->of_node, "gpio-ranges")) {
+		ret = gpiochip_add_pin_range(&pctrl->chip, dev_name(pctrl->dev),
+					     0, 0, pctrl->chip.ngpio);
+		if (ret) {
+			dev_err(pctrl->dev, "failed to add pin range\n");
+			goto unregister_gpiochip;
+		}
+	}
+
+	platform_set_drvdata(pdev, pctrl);
+
+	dev_dbg(&pdev->dev, "Qualcomm pm8xxx gpio driver probed\n");
+
+	return 0;
+
+unregister_gpiochip:
+	gpiochip_remove(&pctrl->chip);
+
+	return ret;
+}
+
+static int pm8xxx_gpio_remove(struct platform_device *pdev)
+{
+	struct pm8xxx_gpio *pctrl = platform_get_drvdata(pdev);
+
+	gpiochip_remove(&pctrl->chip);
+
+	return 0;
+}
+
+static struct platform_driver pm8xxx_gpio_driver = {
+	.driver = {
+		.name = "qcom-ssbi-gpio",
+		.of_match_table = pm8xxx_gpio_of_match,
+	},
+	.probe = pm8xxx_gpio_probe,
+	.remove = pm8xxx_gpio_remove,
+};
+
+module_platform_driver(pm8xxx_gpio_driver);
+
+MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson@sonymobile.com>");
+MODULE_DESCRIPTION("Qualcomm PM8xxx GPIO driver");
+MODULE_LICENSE("GPL v2");