Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 1482 insertions, 0 deletions

diff --git a/drivers/scsi/isci/phy.c b/drivers/scsi/isci/phy.c
new file mode 100644
index 0000000000..743a3c64b0
--- /dev/null
+++ b/drivers/scsi/isci/phy.c
@@ -0,0 +1,1482 @@
+/*
+ * This file is provided under a dual BSD/GPLv2 license.  When using or
+ * redistributing this file, you may do so under either license.
+ *
+ * GPL LICENSE SUMMARY
+ *
+ * Copyright(c) 2008 - 2011 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ * The full GNU General Public License is included in this distribution
+ * in the file called LICENSE.GPL.
+ *
+ * BSD LICENSE
+ *
+ * Copyright(c) 2008 - 2011 Intel Corporation. All rights reserved.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ *   * Redistributions of source code must retain the above copyright
+ *     notice, this list of conditions and the following disclaimer.
+ *   * Redistributions in binary form must reproduce the above copyright
+ *     notice, this list of conditions and the following disclaimer in
+ *     the documentation and/or other materials provided with the
+ *     distribution.
+ *   * Neither the name of Intel Corporation nor the names of its
+ *     contributors may be used to endorse or promote products derived
+ *     from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include "isci.h"
+#include "host.h"
+#include "phy.h"
+#include "scu_event_codes.h"
+#include "probe_roms.h"
+
+#undef C
+#define C(a) (#a)
+static const char *phy_state_name(enum sci_phy_states state)
+{
+	static const char * const strings[] = PHY_STATES;
+
+	return strings[state];
+}
+#undef C
+
+/* Maximum arbitration wait time in micro-seconds */
+#define SCIC_SDS_PHY_MAX_ARBITRATION_WAIT_TIME  (700)
+
+enum sas_linkrate sci_phy_linkrate(struct isci_phy *iphy)
+{
+	return iphy->max_negotiated_speed;
+}
+
+static struct isci_host *phy_to_host(struct isci_phy *iphy)
+{
+	struct isci_phy *table = iphy - iphy->phy_index;
+	struct isci_host *ihost = container_of(table, typeof(*ihost), phys[0]);
+
+	return ihost;
+}
+
+static struct device *sciphy_to_dev(struct isci_phy *iphy)
+{
+	return &phy_to_host(iphy)->pdev->dev;
+}
+
+static enum sci_status
+sci_phy_transport_layer_initialization(struct isci_phy *iphy,
+				       struct scu_transport_layer_registers __iomem *reg)
+{
+	u32 tl_control;
+
+	iphy->transport_layer_registers = reg;
+
+	writel(SCIC_SDS_REMOTE_NODE_CONTEXT_INVALID_INDEX,
+		&iphy->transport_layer_registers->stp_rni);
+
+	/*
+	 * Hardware team recommends that we enable the STP prefetch for all
+	 * transports
+	 */
+	tl_control = readl(&iphy->transport_layer_registers->control);
+	tl_control |= SCU_TLCR_GEN_BIT(STP_WRITE_DATA_PREFETCH);
+	writel(tl_control, &iphy->transport_layer_registers->control);
+
+	return SCI_SUCCESS;
+}
+
+static enum sci_status
+sci_phy_link_layer_initialization(struct isci_phy *iphy,
+				  struct scu_link_layer_registers __iomem *llr)
+{
+	struct isci_host *ihost = iphy->owning_port->owning_controller;
+	struct sci_phy_user_params *phy_user;
+	struct sci_phy_oem_params *phy_oem;
+	int phy_idx = iphy->phy_index;
+	struct sci_phy_cap phy_cap;
+	u32 phy_configuration;
+	u32 parity_check = 0;
+	u32 parity_count = 0;
+	u32 llctl, link_rate;
+	u32 clksm_value = 0;
+	u32 sp_timeouts = 0;
+
+	phy_user = &ihost->user_parameters.phys[phy_idx];
+	phy_oem = &ihost->oem_parameters.phys[phy_idx];
+	iphy->link_layer_registers = llr;
+
+	/* Set our IDENTIFY frame data */
+	#define SCI_END_DEVICE 0x01
+
+	writel(SCU_SAS_TIID_GEN_BIT(SMP_INITIATOR) |
+	       SCU_SAS_TIID_GEN_BIT(SSP_INITIATOR) |
+	       SCU_SAS_TIID_GEN_BIT(STP_INITIATOR) |
+	       SCU_SAS_TIID_GEN_BIT(DA_SATA_HOST) |
+	       SCU_SAS_TIID_GEN_VAL(DEVICE_TYPE, SCI_END_DEVICE),
+	       &llr->transmit_identification);
+
+	/* Write the device SAS Address */
+	writel(0xFEDCBA98, &llr->sas_device_name_high);
+	writel(phy_idx, &llr->sas_device_name_low);
+
+	/* Write the source SAS Address */
+	writel(phy_oem->sas_address.high, &llr->source_sas_address_high);
+	writel(phy_oem->sas_address.low, &llr->source_sas_address_low);
+
+	/* Clear and Set the PHY Identifier */
+	writel(0, &llr->identify_frame_phy_id);
+	writel(SCU_SAS_TIPID_GEN_VALUE(ID, phy_idx), &llr->identify_frame_phy_id);
+
+	/* Change the initial state of the phy configuration register */
+	phy_configuration = readl(&llr->phy_configuration);
+
+	/* Hold OOB state machine in reset */
+	phy_configuration |=  SCU_SAS_PCFG_GEN_BIT(OOB_RESET);
+	writel(phy_configuration, &llr->phy_configuration);
+
+	/* Configure the SNW capabilities */
+	phy_cap.all = 0;
+	phy_cap.start = 1;
+	phy_cap.gen3_no_ssc = 1;
+	phy_cap.gen2_no_ssc = 1;
+	phy_cap.gen1_no_ssc = 1;
+	if (ihost->oem_parameters.controller.do_enable_ssc) {
+		struct scu_afe_registers __iomem *afe = &ihost->scu_registers->afe;
+		struct scu_afe_transceiver __iomem *xcvr = &afe->scu_afe_xcvr[phy_idx];
+		struct isci_pci_info *pci_info = to_pci_info(ihost->pdev);
+		bool en_sas = false;
+		bool en_sata = false;
+		u32 sas_type = 0;
+		u32 sata_spread = 0x2;
+		u32 sas_spread = 0x2;
+
+		phy_cap.gen3_ssc = 1;
+		phy_cap.gen2_ssc = 1;
+		phy_cap.gen1_ssc = 1;
+
+		if (pci_info->orom->hdr.version < ISCI_ROM_VER_1_1)
+			en_sas = en_sata = true;
+		else {
+			sata_spread = ihost->oem_parameters.controller.ssc_sata_tx_spread_level;
+			sas_spread = ihost->oem_parameters.controller.ssc_sas_tx_spread_level;
+
+			if (sata_spread)
+				en_sata = true;
+
+			if (sas_spread) {
+				en_sas = true;
+				sas_type = ihost->oem_parameters.controller.ssc_sas_tx_type;
+			}
+
+		}
+
+		if (en_sas) {
+			u32 reg;
+
+			reg = readl(&xcvr->afe_xcvr_control0);
+			reg |= (0x00100000 | (sas_type << 19));
+			writel(reg, &xcvr->afe_xcvr_control0);
+
+			reg = readl(&xcvr->afe_tx_ssc_control);
+			reg |= sas_spread << 8;
+			writel(reg, &xcvr->afe_tx_ssc_control);
+		}
+
+		if (en_sata) {
+			u32 reg;
+
+			reg = readl(&xcvr->afe_tx_ssc_control);
+			reg |= sata_spread;
+			writel(reg, &xcvr->afe_tx_ssc_control);
+
+			reg = readl(&llr->stp_control);
+			reg |= 1 << 12;
+			writel(reg, &llr->stp_control);
+		}
+	}
+
+	/* The SAS specification indicates that the phy_capabilities that
+	 * are transmitted shall have an even parity.  Calculate the parity.
+	 */
+	parity_check = phy_cap.all;
+	while (parity_check != 0) {
+		if (parity_check & 0x1)
+			parity_count++;
+		parity_check >>= 1;
+	}
+
+	/* If parity indicates there are an odd number of bits set, then
+	 * set the parity bit to 1 in the phy capabilities.
+	 */
+	if ((parity_count % 2) != 0)
+		phy_cap.parity = 1;
+
+	writel(phy_cap.all, &llr->phy_capabilities);
+
+	/* Set the enable spinup period but disable the ability to send
+	 * notify enable spinup
+	 */
+	writel(SCU_ENSPINUP_GEN_VAL(COUNT,
+			phy_user->notify_enable_spin_up_insertion_frequency),
+		&llr->notify_enable_spinup_control);
+
+	/* Write the ALIGN Insertion Ferequency for connected phy and
+	 * inpendent of connected state
+	 */
+	clksm_value = SCU_ALIGN_INSERTION_FREQUENCY_GEN_VAL(CONNECTED,
+			phy_user->in_connection_align_insertion_frequency);
+
+	clksm_value |= SCU_ALIGN_INSERTION_FREQUENCY_GEN_VAL(GENERAL,
+			phy_user->align_insertion_frequency);
+
+	writel(clksm_value, &llr->clock_skew_management);
+
+	if (is_c0(ihost->pdev) || is_c1(ihost->pdev)) {
+		writel(0x04210400, &llr->afe_lookup_table_control);
+		writel(0x020A7C05, &llr->sas_primitive_timeout);
+	} else
+		writel(0x02108421, &llr->afe_lookup_table_control);
+
+	llctl = SCU_SAS_LLCTL_GEN_VAL(NO_OUTBOUND_TASK_TIMEOUT,
+		(u8)ihost->user_parameters.no_outbound_task_timeout);
+
+	switch (phy_user->max_speed_generation) {
+	case SCIC_SDS_PARM_GEN3_SPEED:
+		link_rate = SCU_SAS_LINK_LAYER_CONTROL_MAX_LINK_RATE_GEN3;
+		break;
+	case SCIC_SDS_PARM_GEN2_SPEED:
+		link_rate = SCU_SAS_LINK_LAYER_CONTROL_MAX_LINK_RATE_GEN2;
+		break;
+	default:
+		link_rate = SCU_SAS_LINK_LAYER_CONTROL_MAX_LINK_RATE_GEN1;
+		break;
+	}
+	llctl |= SCU_SAS_LLCTL_GEN_VAL(MAX_LINK_RATE, link_rate);
+	writel(llctl, &llr->link_layer_control);
+
+	sp_timeouts = readl(&llr->sas_phy_timeouts);
+
+	/* Clear the default 0x36 (54us) RATE_CHANGE timeout value. */
+	sp_timeouts &= ~SCU_SAS_PHYTOV_GEN_VAL(RATE_CHANGE, 0xFF);
+
+	/* Set RATE_CHANGE timeout value to 0x3B (59us).  This ensures SCU can
+	 * lock with 3Gb drive when SCU max rate is set to 1.5Gb.
+	 */
+	sp_timeouts |= SCU_SAS_PHYTOV_GEN_VAL(RATE_CHANGE, 0x3B);
+
+	writel(sp_timeouts, &llr->sas_phy_timeouts);
+
+	if (is_a2(ihost->pdev)) {
+		/* Program the max ARB time for the PHY to 700us so we
+		 * inter-operate with the PMC expander which shuts down
+		 * PHYs if the expander PHY generates too many breaks.
+		 * This time value will guarantee that the initiator PHY
+		 * will generate the break.
+		 */
+		writel(SCIC_SDS_PHY_MAX_ARBITRATION_WAIT_TIME,
+		       &llr->maximum_arbitration_wait_timer_timeout);
+	}
+
+	/* Disable link layer hang detection, rely on the OS timeout for
+	 * I/O timeouts.
+	 */
+	writel(0, &llr->link_layer_hang_detection_timeout);
+
+	/* We can exit the initial state to the stopped state */
+	sci_change_state(&iphy->sm, SCI_PHY_STOPPED);
+
+	return SCI_SUCCESS;
+}
+
+static void phy_sata_timeout(struct timer_list *t)
+{
+	struct sci_timer *tmr = from_timer(tmr, t, timer);
+	struct isci_phy *iphy = container_of(tmr, typeof(*iphy), sata_timer);
+	struct isci_host *ihost = iphy->owning_port->owning_controller;
+	unsigned long flags;
+
+	spin_lock_irqsave(&ihost->scic_lock, flags);
+
+	if (tmr->cancel)
+		goto done;
+
+	dev_dbg(sciphy_to_dev(iphy),
+		 "%s: SCIC SDS Phy 0x%p did not receive signature fis before "
+		 "timeout.\n",
+		 __func__,
+		 iphy);
+
+	sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+done:
+	spin_unlock_irqrestore(&ihost->scic_lock, flags);
+}
+
+/**
+ * phy_get_non_dummy_port() - This method returns the port currently containing
+ * this phy. If the phy is currently contained by the dummy port, then the phy
+ * is considered to not be part of a port.
+ *
+ * @iphy: This parameter specifies the phy for which to retrieve the
+ *    containing port.
+ *
+ * This method returns a handle to a port that contains the supplied phy.
+ * NULL This value is returned if the phy is not part of a real
+ * port (i.e. it's contained in the dummy port). !NULL All other
+ * values indicate a handle/pointer to the port containing the phy.
+ */
+struct isci_port *phy_get_non_dummy_port(struct isci_phy *iphy)
+{
+	struct isci_port *iport = iphy->owning_port;
+
+	if (iport->physical_port_index == SCIC_SDS_DUMMY_PORT)
+		return NULL;
+
+	return iphy->owning_port;
+}
+
+/*
+ * sci_phy_set_port() - This method will assign a port to the phy object.
+ */
+void sci_phy_set_port(
+	struct isci_phy *iphy,
+	struct isci_port *iport)
+{
+	iphy->owning_port = iport;
+
+	if (iphy->bcn_received_while_port_unassigned) {
+		iphy->bcn_received_while_port_unassigned = false;
+		sci_port_broadcast_change_received(iphy->owning_port, iphy);
+	}
+}
+
+enum sci_status sci_phy_initialize(struct isci_phy *iphy,
+				   struct scu_transport_layer_registers __iomem *tl,
+				   struct scu_link_layer_registers __iomem *ll)
+{
+	/* Perfrom the initialization of the TL hardware */
+	sci_phy_transport_layer_initialization(iphy, tl);
+
+	/* Perofrm the initialization of the PE hardware */
+	sci_phy_link_layer_initialization(iphy, ll);
+
+	/* There is nothing that needs to be done in this state just
+	 * transition to the stopped state
+	 */
+	sci_change_state(&iphy->sm, SCI_PHY_STOPPED);
+
+	return SCI_SUCCESS;
+}
+
+/**
+ * sci_phy_setup_transport() - This method assigns the direct attached device ID for this phy.
+ *
+ * @iphy: The phy for which the direct attached device id is to
+ *       be assigned.
+ * @device_id: The direct attached device ID to assign to the phy.
+ *       This will either be the RNi for the device or an invalid RNi if there
+ *       is no current device assigned to the phy.
+ */
+void sci_phy_setup_transport(struct isci_phy *iphy, u32 device_id)
+{
+	u32 tl_control;
+
+	writel(device_id, &iphy->transport_layer_registers->stp_rni);
+
+	/*
+	 * The read should guarantee that the first write gets posted
+	 * before the next write
+	 */
+	tl_control = readl(&iphy->transport_layer_registers->control);
+	tl_control |= SCU_TLCR_GEN_BIT(CLEAR_TCI_NCQ_MAPPING_TABLE);
+	writel(tl_control, &iphy->transport_layer_registers->control);
+}
+
+static void sci_phy_suspend(struct isci_phy *iphy)
+{
+	u32 scu_sas_pcfg_value;
+
+	scu_sas_pcfg_value =
+		readl(&iphy->link_layer_registers->phy_configuration);
+	scu_sas_pcfg_value |= SCU_SAS_PCFG_GEN_BIT(SUSPEND_PROTOCOL_ENGINE);
+	writel(scu_sas_pcfg_value,
+		&iphy->link_layer_registers->phy_configuration);
+
+	sci_phy_setup_transport(iphy, SCIC_SDS_REMOTE_NODE_CONTEXT_INVALID_INDEX);
+}
+
+void sci_phy_resume(struct isci_phy *iphy)
+{
+	u32 scu_sas_pcfg_value;
+
+	scu_sas_pcfg_value =
+		readl(&iphy->link_layer_registers->phy_configuration);
+	scu_sas_pcfg_value &= ~SCU_SAS_PCFG_GEN_BIT(SUSPEND_PROTOCOL_ENGINE);
+	writel(scu_sas_pcfg_value,
+		&iphy->link_layer_registers->phy_configuration);
+}
+
+void sci_phy_get_sas_address(struct isci_phy *iphy, struct sci_sas_address *sas)
+{
+	sas->high = readl(&iphy->link_layer_registers->source_sas_address_high);
+	sas->low = readl(&iphy->link_layer_registers->source_sas_address_low);
+}
+
+void sci_phy_get_attached_sas_address(struct isci_phy *iphy, struct sci_sas_address *sas)
+{
+	struct sas_identify_frame *iaf;
+
+	iaf = &iphy->frame_rcvd.iaf;
+	memcpy(sas, iaf->sas_addr, SAS_ADDR_SIZE);
+}
+
+void sci_phy_get_protocols(struct isci_phy *iphy, struct sci_phy_proto *proto)
+{
+	proto->all = readl(&iphy->link_layer_registers->transmit_identification);
+}
+
+enum sci_status sci_phy_start(struct isci_phy *iphy)
+{
+	enum sci_phy_states state = iphy->sm.current_state_id;
+
+	if (state != SCI_PHY_STOPPED) {
+		dev_dbg(sciphy_to_dev(iphy), "%s: in wrong state: %s\n",
+			__func__, phy_state_name(state));
+		return SCI_FAILURE_INVALID_STATE;
+	}
+
+	sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+	return SCI_SUCCESS;
+}
+
+enum sci_status sci_phy_stop(struct isci_phy *iphy)
+{
+	enum sci_phy_states state = iphy->sm.current_state_id;
+
+	switch (state) {
+	case SCI_PHY_SUB_INITIAL:
+	case SCI_PHY_SUB_AWAIT_OSSP_EN:
+	case SCI_PHY_SUB_AWAIT_SAS_SPEED_EN:
+	case SCI_PHY_SUB_AWAIT_SAS_POWER:
+	case SCI_PHY_SUB_AWAIT_SATA_POWER:
+	case SCI_PHY_SUB_AWAIT_SATA_PHY_EN:
+	case SCI_PHY_SUB_AWAIT_SATA_SPEED_EN:
+	case SCI_PHY_SUB_AWAIT_SIG_FIS_UF:
+	case SCI_PHY_SUB_FINAL:
+	case SCI_PHY_READY:
+		break;
+	default:
+		dev_dbg(sciphy_to_dev(iphy), "%s: in wrong state: %s\n",
+			__func__, phy_state_name(state));
+		return SCI_FAILURE_INVALID_STATE;
+	}
+
+	sci_change_state(&iphy->sm, SCI_PHY_STOPPED);
+	return SCI_SUCCESS;
+}
+
+enum sci_status sci_phy_reset(struct isci_phy *iphy)
+{
+	enum sci_phy_states state = iphy->sm.current_state_id;
+
+	if (state != SCI_PHY_READY) {
+		dev_dbg(sciphy_to_dev(iphy), "%s: in wrong state: %s\n",
+			__func__, phy_state_name(state));
+		return SCI_FAILURE_INVALID_STATE;
+	}
+
+	sci_change_state(&iphy->sm, SCI_PHY_RESETTING);
+	return SCI_SUCCESS;
+}
+
+enum sci_status sci_phy_consume_power_handler(struct isci_phy *iphy)
+{
+	enum sci_phy_states state = iphy->sm.current_state_id;
+
+	switch (state) {
+	case SCI_PHY_SUB_AWAIT_SAS_POWER: {
+		u32 enable_spinup;
+
+		enable_spinup = readl(&iphy->link_layer_registers->notify_enable_spinup_control);
+		enable_spinup |= SCU_ENSPINUP_GEN_BIT(ENABLE);
+		writel(enable_spinup, &iphy->link_layer_registers->notify_enable_spinup_control);
+
+		/* Change state to the final state this substate machine has run to completion */
+		sci_change_state(&iphy->sm, SCI_PHY_SUB_FINAL);
+
+		return SCI_SUCCESS;
+	}
+	case SCI_PHY_SUB_AWAIT_SATA_POWER: {
+		u32 scu_sas_pcfg_value;
+
+		/* Release the spinup hold state and reset the OOB state machine */
+		scu_sas_pcfg_value =
+			readl(&iphy->link_layer_registers->phy_configuration);
+		scu_sas_pcfg_value &=
+			~(SCU_SAS_PCFG_GEN_BIT(SATA_SPINUP_HOLD) | SCU_SAS_PCFG_GEN_BIT(OOB_ENABLE));
+		scu_sas_pcfg_value |= SCU_SAS_PCFG_GEN_BIT(OOB_RESET);
+		writel(scu_sas_pcfg_value,
+			&iphy->link_layer_registers->phy_configuration);
+
+		/* Now restart the OOB operation */
+		scu_sas_pcfg_value &= ~SCU_SAS_PCFG_GEN_BIT(OOB_RESET);
+		scu_sas_pcfg_value |= SCU_SAS_PCFG_GEN_BIT(OOB_ENABLE);
+		writel(scu_sas_pcfg_value,
+			&iphy->link_layer_registers->phy_configuration);
+
+		/* Change state to the final state this substate machine has run to completion */
+		sci_change_state(&iphy->sm, SCI_PHY_SUB_AWAIT_SATA_PHY_EN);
+
+		return SCI_SUCCESS;
+	}
+	default:
+		dev_dbg(sciphy_to_dev(iphy), "%s: in wrong state: %s\n",
+			__func__, phy_state_name(state));
+		return SCI_FAILURE_INVALID_STATE;
+	}
+}
+
+static void sci_phy_start_sas_link_training(struct isci_phy *iphy)
+{
+	/* continue the link training for the phy as if it were a SAS PHY
+	 * instead of a SATA PHY. This is done because the completion queue had a SAS
+	 * PHY DETECTED event when the state machine was expecting a SATA PHY event.
+	 */
+	u32 phy_control;
+
+	phy_control = readl(&iphy->link_layer_registers->phy_configuration);
+	phy_control |= SCU_SAS_PCFG_GEN_BIT(SATA_SPINUP_HOLD);
+	writel(phy_control,
+	       &iphy->link_layer_registers->phy_configuration);
+
+	sci_change_state(&iphy->sm, SCI_PHY_SUB_AWAIT_SAS_SPEED_EN);
+
+	iphy->protocol = SAS_PROTOCOL_SSP;
+}
+
+static void sci_phy_start_sata_link_training(struct isci_phy *iphy)
+{
+	/* This method continues the link training for the phy as if it were a SATA PHY
+	 * instead of a SAS PHY.  This is done because the completion queue had a SATA
+	 * SPINUP HOLD event when the state machine was expecting a SAS PHY event. none
+	 */
+	sci_change_state(&iphy->sm, SCI_PHY_SUB_AWAIT_SATA_POWER);
+
+	iphy->protocol = SAS_PROTOCOL_SATA;
+}
+
+/**
+ * sci_phy_complete_link_training - perform processing common to
+ *    all protocols upon completion of link training.
+ * @iphy: This parameter specifies the phy object for which link training
+ *    has completed.
+ * @max_link_rate: This parameter specifies the maximum link rate to be
+ *    associated with this phy.
+ * @next_state: This parameter specifies the next state for the phy's starting
+ *    sub-state machine.
+ *
+ */
+static void sci_phy_complete_link_training(struct isci_phy *iphy,
+					   enum sas_linkrate max_link_rate,
+					   u32 next_state)
+{
+	iphy->max_negotiated_speed = max_link_rate;
+
+	sci_change_state(&iphy->sm, next_state);
+}
+
+static const char *phy_event_name(u32 event_code)
+{
+	switch (scu_get_event_code(event_code)) {
+	case SCU_EVENT_PORT_SELECTOR_DETECTED:
+		return "port selector";
+	case SCU_EVENT_SENT_PORT_SELECTION:
+		return "port selection";
+	case SCU_EVENT_HARD_RESET_TRANSMITTED:
+		return "tx hard reset";
+	case SCU_EVENT_HARD_RESET_RECEIVED:
+		return "rx hard reset";
+	case SCU_EVENT_RECEIVED_IDENTIFY_TIMEOUT:
+		return "identify timeout";
+	case SCU_EVENT_LINK_FAILURE:
+		return "link fail";
+	case SCU_EVENT_SATA_SPINUP_HOLD:
+		return "sata spinup hold";
+	case SCU_EVENT_SAS_15_SSC:
+	case SCU_EVENT_SAS_15:
+		return "sas 1.5";
+	case SCU_EVENT_SAS_30_SSC:
+	case SCU_EVENT_SAS_30:
+		return "sas 3.0";
+	case SCU_EVENT_SAS_60_SSC:
+	case SCU_EVENT_SAS_60:
+		return "sas 6.0";
+	case SCU_EVENT_SATA_15_SSC:
+	case SCU_EVENT_SATA_15:
+		return "sata 1.5";
+	case SCU_EVENT_SATA_30_SSC:
+	case SCU_EVENT_SATA_30:
+		return "sata 3.0";
+	case SCU_EVENT_SATA_60_SSC:
+	case SCU_EVENT_SATA_60:
+		return "sata 6.0";
+	case SCU_EVENT_SAS_PHY_DETECTED:
+		return "sas detect";
+	case SCU_EVENT_SATA_PHY_DETECTED:
+		return "sata detect";
+	default:
+		return "unknown";
+	}
+}
+
+#define phy_event_dbg(iphy, state, code) \
+	dev_dbg(sciphy_to_dev(iphy), "phy-%d:%d: %s event: %s (%x)\n", \
+		phy_to_host(iphy)->id, iphy->phy_index, \
+		phy_state_name(state), phy_event_name(code), code)
+
+#define phy_event_warn(iphy, state, code) \
+	dev_warn(sciphy_to_dev(iphy), "phy-%d:%d: %s event: %s (%x)\n", \
+		phy_to_host(iphy)->id, iphy->phy_index, \
+		phy_state_name(state), phy_event_name(code), code)
+
+
+static void scu_link_layer_set_txcomsas_timeout(struct isci_phy *iphy, u32 timeout)
+{
+	u32 val;
+
+	/* Extend timeout */
+	val = readl(&iphy->link_layer_registers->transmit_comsas_signal);
+	val &= ~SCU_SAS_LLTXCOMSAS_GEN_VAL(NEGTIME, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_MASK);
+	val |= SCU_SAS_LLTXCOMSAS_GEN_VAL(NEGTIME, timeout);
+
+	writel(val, &iphy->link_layer_registers->transmit_comsas_signal);
+}
+
+enum sci_status sci_phy_event_handler(struct isci_phy *iphy, u32 event_code)
+{
+	enum sci_phy_states state = iphy->sm.current_state_id;
+
+	switch (state) {
+	case SCI_PHY_SUB_AWAIT_OSSP_EN:
+		switch (scu_get_event_code(event_code)) {
+		case SCU_EVENT_SAS_PHY_DETECTED:
+			sci_phy_start_sas_link_training(iphy);
+			iphy->is_in_link_training = true;
+			break;
+		case SCU_EVENT_SATA_SPINUP_HOLD:
+			sci_phy_start_sata_link_training(iphy);
+			iphy->is_in_link_training = true;
+			break;
+		case SCU_EVENT_RECEIVED_IDENTIFY_TIMEOUT:
+		       /* Extend timeout value */
+		       scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_EXTENDED);
+
+		       /* Start the oob/sn state machine over again */
+		       sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+		       break;
+		default:
+			phy_event_dbg(iphy, state, event_code);
+			return SCI_FAILURE;
+		}
+		return SCI_SUCCESS;
+	case SCI_PHY_SUB_AWAIT_SAS_SPEED_EN:
+		switch (scu_get_event_code(event_code)) {
+		case SCU_EVENT_SAS_PHY_DETECTED:
+			/*
+			 * Why is this being reported again by the controller?
+			 * We would re-enter this state so just stay here */
+			break;
+		case SCU_EVENT_SAS_15:
+		case SCU_EVENT_SAS_15_SSC:
+			sci_phy_complete_link_training(iphy, SAS_LINK_RATE_1_5_GBPS,
+						       SCI_PHY_SUB_AWAIT_IAF_UF);
+			break;
+		case SCU_EVENT_SAS_30:
+		case SCU_EVENT_SAS_30_SSC:
+			sci_phy_complete_link_training(iphy, SAS_LINK_RATE_3_0_GBPS,
+						       SCI_PHY_SUB_AWAIT_IAF_UF);
+			break;
+		case SCU_EVENT_SAS_60:
+		case SCU_EVENT_SAS_60_SSC:
+			sci_phy_complete_link_training(iphy, SAS_LINK_RATE_6_0_GBPS,
+						       SCI_PHY_SUB_AWAIT_IAF_UF);
+			break;
+		case SCU_EVENT_SATA_SPINUP_HOLD:
+			/*
+			 * We were doing SAS PHY link training and received a SATA PHY event
+			 * continue OOB/SN as if this were a SATA PHY */
+			sci_phy_start_sata_link_training(iphy);
+			break;
+		case SCU_EVENT_LINK_FAILURE:
+			/* Change the timeout value to default */
+			scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT);
+
+			/* Link failure change state back to the starting state */
+			sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+			break;
+		case SCU_EVENT_RECEIVED_IDENTIFY_TIMEOUT:
+		       /* Extend the timeout value */
+		       scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_EXTENDED);
+
+		       /* Start the oob/sn state machine over again */
+		       sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+		       break;
+		default:
+			phy_event_warn(iphy, state, event_code);
+			return SCI_FAILURE;
+		}
+		return SCI_SUCCESS;
+	case SCI_PHY_SUB_AWAIT_IAF_UF:
+		switch (scu_get_event_code(event_code)) {
+		case SCU_EVENT_SAS_PHY_DETECTED:
+			/* Backup the state machine */
+			sci_phy_start_sas_link_training(iphy);
+			break;
+		case SCU_EVENT_SATA_SPINUP_HOLD:
+			/* We were doing SAS PHY link training and received a
+			 * SATA PHY event continue OOB/SN as if this were a
+			 * SATA PHY
+			 */
+			sci_phy_start_sata_link_training(iphy);
+			break;
+		case SCU_EVENT_RECEIVED_IDENTIFY_TIMEOUT:
+			/* Extend the timeout value */
+			scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_EXTENDED);
+
+			/* Start the oob/sn state machine over again */
+			sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+			break;
+		case SCU_EVENT_LINK_FAILURE:
+			scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT);
+			fallthrough;
+		case SCU_EVENT_HARD_RESET_RECEIVED:
+			/* Start the oob/sn state machine over again */
+			sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+			break;
+		default:
+			phy_event_warn(iphy, state, event_code);
+			return SCI_FAILURE;
+		}
+		return SCI_SUCCESS;
+	case SCI_PHY_SUB_AWAIT_SAS_POWER:
+		switch (scu_get_event_code(event_code)) {
+		case SCU_EVENT_LINK_FAILURE:
+			/* Change the timeout value to default */
+			scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT);
+
+			/* Link failure change state back to the starting state */
+			sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+			break;
+		default:
+			phy_event_warn(iphy, state, event_code);
+			return SCI_FAILURE;
+		}
+		return SCI_SUCCESS;
+	case SCI_PHY_SUB_AWAIT_SATA_POWER:
+		switch (scu_get_event_code(event_code)) {
+		case SCU_EVENT_LINK_FAILURE:
+			/* Change the timeout value to default */
+			scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT);
+
+			/* Link failure change state back to the starting state */
+			sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+			break;
+		case SCU_EVENT_SATA_SPINUP_HOLD:
+			/* These events are received every 10ms and are
+			 * expected while in this state
+			 */
+			break;
+
+		case SCU_EVENT_SAS_PHY_DETECTED:
+			/* There has been a change in the phy type before OOB/SN for the
+			 * SATA finished start down the SAS link traning path.
+			 */
+			sci_phy_start_sas_link_training(iphy);
+			break;
+
+		default:
+			phy_event_warn(iphy, state, event_code);
+			return SCI_FAILURE;
+		}
+		return SCI_SUCCESS;
+	case SCI_PHY_SUB_AWAIT_SATA_PHY_EN:
+		switch (scu_get_event_code(event_code)) {
+		case SCU_EVENT_LINK_FAILURE:
+			/* Change the timeout value to default */
+			scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT);
+
+			/* Link failure change state back to the starting state */
+			sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+			break;
+		case SCU_EVENT_SATA_SPINUP_HOLD:
+			/* These events might be received since we dont know how many may be in
+			 * the completion queue while waiting for power
+			 */
+			break;
+		case SCU_EVENT_SATA_PHY_DETECTED:
+			iphy->protocol = SAS_PROTOCOL_SATA;
+
+			/* We have received the SATA PHY notification change state */
+			sci_change_state(&iphy->sm, SCI_PHY_SUB_AWAIT_SATA_SPEED_EN);
+			break;
+		case SCU_EVENT_SAS_PHY_DETECTED:
+			/* There has been a change in the phy type before OOB/SN for the
+			 * SATA finished start down the SAS link traning path.
+			 */
+			sci_phy_start_sas_link_training(iphy);
+			break;
+		default:
+			phy_event_warn(iphy, state, event_code);
+			return SCI_FAILURE;
+		}
+		return SCI_SUCCESS;
+	case SCI_PHY_SUB_AWAIT_SATA_SPEED_EN:
+		switch (scu_get_event_code(event_code)) {
+		case SCU_EVENT_SATA_PHY_DETECTED:
+			/*
+			 * The hardware reports multiple SATA PHY detected events
+			 * ignore the extras */
+			break;
+		case SCU_EVENT_SATA_15:
+		case SCU_EVENT_SATA_15_SSC:
+			sci_phy_complete_link_training(iphy, SAS_LINK_RATE_1_5_GBPS,
+						       SCI_PHY_SUB_AWAIT_SIG_FIS_UF);
+			break;
+		case SCU_EVENT_SATA_30:
+		case SCU_EVENT_SATA_30_SSC:
+			sci_phy_complete_link_training(iphy, SAS_LINK_RATE_3_0_GBPS,
+						       SCI_PHY_SUB_AWAIT_SIG_FIS_UF);
+			break;
+		case SCU_EVENT_SATA_60:
+		case SCU_EVENT_SATA_60_SSC:
+			sci_phy_complete_link_training(iphy, SAS_LINK_RATE_6_0_GBPS,
+						       SCI_PHY_SUB_AWAIT_SIG_FIS_UF);
+			break;
+		case SCU_EVENT_LINK_FAILURE:
+			/* Change the timeout value to default */
+			scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT);
+
+			/* Link failure change state back to the starting state */
+			sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+			break;
+		case SCU_EVENT_SAS_PHY_DETECTED:
+			/*
+			 * There has been a change in the phy type before OOB/SN for the
+			 * SATA finished start down the SAS link traning path. */
+			sci_phy_start_sas_link_training(iphy);
+			break;
+		default:
+			phy_event_warn(iphy, state, event_code);
+			return SCI_FAILURE;
+		}
+
+		return SCI_SUCCESS;
+	case SCI_PHY_SUB_AWAIT_SIG_FIS_UF:
+		switch (scu_get_event_code(event_code)) {
+		case SCU_EVENT_SATA_PHY_DETECTED:
+			/* Backup the state machine */
+			sci_change_state(&iphy->sm, SCI_PHY_SUB_AWAIT_SATA_SPEED_EN);
+			break;
+
+		case SCU_EVENT_LINK_FAILURE:
+			/* Change the timeout value to default */
+			scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT);
+
+			/* Link failure change state back to the starting state */
+			sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+			break;
+
+		default:
+			phy_event_warn(iphy, state, event_code);
+			return SCI_FAILURE;
+		}
+		return SCI_SUCCESS;
+	case SCI_PHY_READY:
+		switch (scu_get_event_code(event_code)) {
+		case SCU_EVENT_LINK_FAILURE:
+			/* Set default timeout */
+			scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT);
+
+			/* Link failure change state back to the starting state */
+			sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+			break;
+		case SCU_EVENT_BROADCAST_CHANGE:
+		case SCU_EVENT_BROADCAST_SES:
+		case SCU_EVENT_BROADCAST_RESERVED0:
+		case SCU_EVENT_BROADCAST_RESERVED1:
+		case SCU_EVENT_BROADCAST_EXPANDER:
+		case SCU_EVENT_BROADCAST_AEN:
+			/* Broadcast change received. Notify the port. */
+			if (phy_get_non_dummy_port(iphy) != NULL)
+				sci_port_broadcast_change_received(iphy->owning_port, iphy);
+			else
+				iphy->bcn_received_while_port_unassigned = true;
+			break;
+		case SCU_EVENT_BROADCAST_RESERVED3:
+		case SCU_EVENT_BROADCAST_RESERVED4:
+		default:
+			phy_event_warn(iphy, state, event_code);
+			return SCI_FAILURE_INVALID_STATE;
+		}
+		return SCI_SUCCESS;
+	case SCI_PHY_RESETTING:
+		switch (scu_get_event_code(event_code)) {
+		case SCU_EVENT_HARD_RESET_TRANSMITTED:
+			/* Link failure change state back to the starting state */
+			sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+			break;
+		default:
+			phy_event_warn(iphy, state, event_code);
+			return SCI_FAILURE_INVALID_STATE;
+		}
+		return SCI_SUCCESS;
+	default:
+		dev_dbg(sciphy_to_dev(iphy), "%s: in wrong state: %s\n",
+			__func__, phy_state_name(state));
+		return SCI_FAILURE_INVALID_STATE;
+	}
+}
+
+enum sci_status sci_phy_frame_handler(struct isci_phy *iphy, u32 frame_index)
+{
+	enum sci_phy_states state = iphy->sm.current_state_id;
+	struct isci_host *ihost = iphy->owning_port->owning_controller;
+	enum sci_status result;
+	unsigned long flags;
+
+	switch (state) {
+	case SCI_PHY_SUB_AWAIT_IAF_UF: {
+		u32 *frame_words;
+		struct sas_identify_frame iaf;
+
+		result = sci_unsolicited_frame_control_get_header(&ihost->uf_control,
+								  frame_index,
+								  (void **)&frame_words);
+
+		if (result != SCI_SUCCESS)
+			return result;
+
+		sci_swab32_cpy(&iaf, frame_words, sizeof(iaf) / sizeof(u32));
+		if (iaf.frame_type == 0) {
+			u32 state;
+
+			spin_lock_irqsave(&iphy->sas_phy.frame_rcvd_lock, flags);
+			memcpy(&iphy->frame_rcvd.iaf, &iaf, sizeof(iaf));
+			spin_unlock_irqrestore(&iphy->sas_phy.frame_rcvd_lock, flags);
+			if (iaf.smp_tport) {
+				/* We got the IAF for an expander PHY go to the final
+				 * state since there are no power requirements for
+				 * expander phys.
+				 */
+				state = SCI_PHY_SUB_FINAL;
+			} else {
+				/* We got the IAF we can now go to the await spinup
+				 * semaphore state
+				 */
+				state = SCI_PHY_SUB_AWAIT_SAS_POWER;
+			}
+			sci_change_state(&iphy->sm, state);
+			result = SCI_SUCCESS;
+		} else
+			dev_warn(sciphy_to_dev(iphy),
+				"%s: PHY starting substate machine received "
+				"unexpected frame id %x\n",
+				__func__, frame_index);
+
+		sci_controller_release_frame(ihost, frame_index);
+		return result;
+	}
+	case SCI_PHY_SUB_AWAIT_SIG_FIS_UF: {
+		struct dev_to_host_fis *frame_header;
+		u32 *fis_frame_data;
+
+		result = sci_unsolicited_frame_control_get_header(&ihost->uf_control,
+								  frame_index,
+								  (void **)&frame_header);
+
+		if (result != SCI_SUCCESS)
+			return result;
+
+		if ((frame_header->fis_type == FIS_REGD2H) &&
+		    !(frame_header->status & ATA_BUSY)) {
+			sci_unsolicited_frame_control_get_buffer(&ihost->uf_control,
+								 frame_index,
+								 (void **)&fis_frame_data);
+
+			spin_lock_irqsave(&iphy->sas_phy.frame_rcvd_lock, flags);
+			sci_controller_copy_sata_response(&iphy->frame_rcvd.fis,
+							  frame_header,
+							  fis_frame_data);
+			spin_unlock_irqrestore(&iphy->sas_phy.frame_rcvd_lock, flags);
+
+			/* got IAF we can now go to the await spinup semaphore state */
+			sci_change_state(&iphy->sm, SCI_PHY_SUB_FINAL);
+
+			result = SCI_SUCCESS;
+		} else
+			dev_warn(sciphy_to_dev(iphy),
+				 "%s: PHY starting substate machine received "
+				 "unexpected frame id %x\n",
+				 __func__, frame_index);
+
+		/* Regardless of the result we are done with this frame with it */
+		sci_controller_release_frame(ihost, frame_index);
+
+		return result;
+	}
+	default:
+		dev_dbg(sciphy_to_dev(iphy), "%s: in wrong state: %s\n",
+			__func__, phy_state_name(state));
+		return SCI_FAILURE_INVALID_STATE;
+	}
+
+}
+
+static void sci_phy_starting_initial_substate_enter(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+
+	/* This is just an temporary state go off to the starting state */
+	sci_change_state(&iphy->sm, SCI_PHY_SUB_AWAIT_OSSP_EN);
+}
+
+static void sci_phy_starting_await_sas_power_substate_enter(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+	struct isci_host *ihost = iphy->owning_port->owning_controller;
+
+	sci_controller_power_control_queue_insert(ihost, iphy);
+}
+
+static void sci_phy_starting_await_sas_power_substate_exit(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+	struct isci_host *ihost = iphy->owning_port->owning_controller;
+
+	sci_controller_power_control_queue_remove(ihost, iphy);
+}
+
+static void sci_phy_starting_await_sata_power_substate_enter(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+	struct isci_host *ihost = iphy->owning_port->owning_controller;
+
+	sci_controller_power_control_queue_insert(ihost, iphy);
+}
+
+static void sci_phy_starting_await_sata_power_substate_exit(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+	struct isci_host *ihost = iphy->owning_port->owning_controller;
+
+	sci_controller_power_control_queue_remove(ihost, iphy);
+}
+
+static void sci_phy_starting_await_sata_phy_substate_enter(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+
+	sci_mod_timer(&iphy->sata_timer, SCIC_SDS_SATA_LINK_TRAINING_TIMEOUT);
+}
+
+static void sci_phy_starting_await_sata_phy_substate_exit(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+
+	sci_del_timer(&iphy->sata_timer);
+}
+
+static void sci_phy_starting_await_sata_speed_substate_enter(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+
+	sci_mod_timer(&iphy->sata_timer, SCIC_SDS_SATA_LINK_TRAINING_TIMEOUT);
+}
+
+static void sci_phy_starting_await_sata_speed_substate_exit(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+
+	sci_del_timer(&iphy->sata_timer);
+}
+
+static void sci_phy_starting_await_sig_fis_uf_substate_enter(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+
+	if (sci_port_link_detected(iphy->owning_port, iphy)) {
+
+		/*
+		 * Clear the PE suspend condition so we can actually
+		 * receive SIG FIS
+		 * The hardware will not respond to the XRDY until the PE
+		 * suspend condition is cleared.
+		 */
+		sci_phy_resume(iphy);
+
+		sci_mod_timer(&iphy->sata_timer,
+			      SCIC_SDS_SIGNATURE_FIS_TIMEOUT);
+	} else
+		iphy->is_in_link_training = false;
+}
+
+static void sci_phy_starting_await_sig_fis_uf_substate_exit(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+
+	sci_del_timer(&iphy->sata_timer);
+}
+
+static void sci_phy_starting_final_substate_enter(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+
+	/* State machine has run to completion so exit out and change
+	 * the base state machine to the ready state
+	 */
+	sci_change_state(&iphy->sm, SCI_PHY_READY);
+}
+
+/**
+ * scu_link_layer_stop_protocol_engine()
+ * @iphy: This is the struct isci_phy object to stop.
+ *
+ * This method will stop the struct isci_phy object. This does not reset the
+ * protocol engine it just suspends it and places it in a state where it will
+ * not cause the end device to power up. none
+ */
+static void scu_link_layer_stop_protocol_engine(
+	struct isci_phy *iphy)
+{
+	u32 scu_sas_pcfg_value;
+	u32 enable_spinup_value;
+
+	/* Suspend the protocol engine and place it in a sata spinup hold state */
+	scu_sas_pcfg_value =
+		readl(&iphy->link_layer_registers->phy_configuration);
+	scu_sas_pcfg_value |=
+		(SCU_SAS_PCFG_GEN_BIT(OOB_RESET) |
+		 SCU_SAS_PCFG_GEN_BIT(SUSPEND_PROTOCOL_ENGINE) |
+		 SCU_SAS_PCFG_GEN_BIT(SATA_SPINUP_HOLD));
+	writel(scu_sas_pcfg_value,
+	       &iphy->link_layer_registers->phy_configuration);
+
+	/* Disable the notify enable spinup primitives */
+	enable_spinup_value = readl(&iphy->link_layer_registers->notify_enable_spinup_control);
+	enable_spinup_value &= ~SCU_ENSPINUP_GEN_BIT(ENABLE);
+	writel(enable_spinup_value, &iphy->link_layer_registers->notify_enable_spinup_control);
+}
+
+static void scu_link_layer_start_oob(struct isci_phy *iphy)
+{
+	struct scu_link_layer_registers __iomem *ll = iphy->link_layer_registers;
+	u32 val;
+
+	/** Reset OOB sequence - start */
+	val = readl(&ll->phy_configuration);
+	val &= ~(SCU_SAS_PCFG_GEN_BIT(OOB_RESET) |
+		 SCU_SAS_PCFG_GEN_BIT(OOB_ENABLE) |
+		 SCU_SAS_PCFG_GEN_BIT(HARD_RESET));
+	writel(val, &ll->phy_configuration);
+	readl(&ll->phy_configuration); /* flush */
+	/** Reset OOB sequence - end */
+
+	/** Start OOB sequence - start */
+	val = readl(&ll->phy_configuration);
+	val |= SCU_SAS_PCFG_GEN_BIT(OOB_ENABLE);
+	writel(val, &ll->phy_configuration);
+	readl(&ll->phy_configuration); /* flush */
+	/** Start OOB sequence - end */
+}
+
+/**
+ * scu_link_layer_tx_hard_reset()
+ * @iphy: This is the struct isci_phy object to stop.
+ *
+ * This method will transmit a hard reset request on the specified phy. The SCU
+ * hardware requires that we reset the OOB state machine and set the hard reset
+ * bit in the phy configuration register. We then must start OOB over with the
+ * hard reset bit set.
+ */
+static void scu_link_layer_tx_hard_reset(
+	struct isci_phy *iphy)
+{
+	u32 phy_configuration_value;
+
+	/*
+	 * SAS Phys must wait for the HARD_RESET_TX event notification to transition
+	 * to the starting state. */
+	phy_configuration_value =
+		readl(&iphy->link_layer_registers->phy_configuration);
+	phy_configuration_value &= ~(SCU_SAS_PCFG_GEN_BIT(OOB_ENABLE));
+	phy_configuration_value |=
+		(SCU_SAS_PCFG_GEN_BIT(HARD_RESET) |
+		 SCU_SAS_PCFG_GEN_BIT(OOB_RESET));
+	writel(phy_configuration_value,
+	       &iphy->link_layer_registers->phy_configuration);
+
+	/* Now take the OOB state machine out of reset */
+	phy_configuration_value |= SCU_SAS_PCFG_GEN_BIT(OOB_ENABLE);
+	phy_configuration_value &= ~SCU_SAS_PCFG_GEN_BIT(OOB_RESET);
+	writel(phy_configuration_value,
+	       &iphy->link_layer_registers->phy_configuration);
+}
+
+static void sci_phy_stopped_state_enter(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+	struct isci_port *iport = iphy->owning_port;
+	struct isci_host *ihost = iport->owning_controller;
+
+	/*
+	 * @todo We need to get to the controller to place this PE in a
+	 * reset state
+	 */
+	sci_del_timer(&iphy->sata_timer);
+
+	scu_link_layer_stop_protocol_engine(iphy);
+
+	if (iphy->sm.previous_state_id != SCI_PHY_INITIAL)
+		sci_controller_link_down(ihost, phy_get_non_dummy_port(iphy), iphy);
+}
+
+static void sci_phy_starting_state_enter(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+	struct isci_port *iport = iphy->owning_port;
+	struct isci_host *ihost = iport->owning_controller;
+
+	scu_link_layer_stop_protocol_engine(iphy);
+	scu_link_layer_start_oob(iphy);
+
+	/* We don't know what kind of phy we are going to be just yet */
+	iphy->protocol = SAS_PROTOCOL_NONE;
+	iphy->bcn_received_while_port_unassigned = false;
+
+	if (iphy->sm.previous_state_id == SCI_PHY_READY)
+		sci_controller_link_down(ihost, phy_get_non_dummy_port(iphy), iphy);
+
+	sci_change_state(&iphy->sm, SCI_PHY_SUB_INITIAL);
+}
+
+static void sci_phy_ready_state_enter(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+	struct isci_port *iport = iphy->owning_port;
+	struct isci_host *ihost = iport->owning_controller;
+
+	sci_controller_link_up(ihost, phy_get_non_dummy_port(iphy), iphy);
+}
+
+static void sci_phy_ready_state_exit(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+
+	sci_phy_suspend(iphy);
+}
+
+static void sci_phy_resetting_state_enter(struct sci_base_state_machine *sm)
+{
+	struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm);
+
+	/* The phy is being reset, therefore deactivate it from the port.  In
+	 * the resetting state we don't notify the user regarding link up and
+	 * link down notifications
+	 */
+	sci_port_deactivate_phy(iphy->owning_port, iphy, false);
+
+	if (iphy->protocol == SAS_PROTOCOL_SSP) {
+		scu_link_layer_tx_hard_reset(iphy);
+	} else {
+		/* The SCU does not need to have a discrete reset state so
+		 * just go back to the starting state.
+		 */
+		sci_change_state(&iphy->sm, SCI_PHY_STARTING);
+	}
+}
+
+static const struct sci_base_state sci_phy_state_table[] = {
+	[SCI_PHY_INITIAL] = { },
+	[SCI_PHY_STOPPED] = {
+		.enter_state = sci_phy_stopped_state_enter,
+	},
+	[SCI_PHY_STARTING] = {
+		.enter_state = sci_phy_starting_state_enter,
+	},
+	[SCI_PHY_SUB_INITIAL] = {
+		.enter_state = sci_phy_starting_initial_substate_enter,
+	},
+	[SCI_PHY_SUB_AWAIT_OSSP_EN] = { },
+	[SCI_PHY_SUB_AWAIT_SAS_SPEED_EN] = { },
+	[SCI_PHY_SUB_AWAIT_IAF_UF] = { },
+	[SCI_PHY_SUB_AWAIT_SAS_POWER] = {
+		.enter_state = sci_phy_starting_await_sas_power_substate_enter,
+		.exit_state  = sci_phy_starting_await_sas_power_substate_exit,
+	},
+	[SCI_PHY_SUB_AWAIT_SATA_POWER] = {
+		.enter_state = sci_phy_starting_await_sata_power_substate_enter,
+		.exit_state  = sci_phy_starting_await_sata_power_substate_exit
+	},
+	[SCI_PHY_SUB_AWAIT_SATA_PHY_EN] = {
+		.enter_state = sci_phy_starting_await_sata_phy_substate_enter,
+		.exit_state  = sci_phy_starting_await_sata_phy_substate_exit
+	},
+	[SCI_PHY_SUB_AWAIT_SATA_SPEED_EN] = {
+		.enter_state = sci_phy_starting_await_sata_speed_substate_enter,
+		.exit_state  = sci_phy_starting_await_sata_speed_substate_exit
+	},
+	[SCI_PHY_SUB_AWAIT_SIG_FIS_UF] = {
+		.enter_state = sci_phy_starting_await_sig_fis_uf_substate_enter,
+		.exit_state  = sci_phy_starting_await_sig_fis_uf_substate_exit
+	},
+	[SCI_PHY_SUB_FINAL] = {
+		.enter_state = sci_phy_starting_final_substate_enter,
+	},
+	[SCI_PHY_READY] = {
+		.enter_state = sci_phy_ready_state_enter,
+		.exit_state = sci_phy_ready_state_exit,
+	},
+	[SCI_PHY_RESETTING] = {
+		.enter_state = sci_phy_resetting_state_enter,
+	},
+	[SCI_PHY_FINAL] = { },
+};
+
+void sci_phy_construct(struct isci_phy *iphy,
+			    struct isci_port *iport, u8 phy_index)
+{
+	sci_init_sm(&iphy->sm, sci_phy_state_table, SCI_PHY_INITIAL);
+
+	/* Copy the rest of the input data to our locals */
+	iphy->owning_port = iport;
+	iphy->phy_index = phy_index;
+	iphy->bcn_received_while_port_unassigned = false;
+	iphy->protocol = SAS_PROTOCOL_NONE;
+	iphy->link_layer_registers = NULL;
+	iphy->max_negotiated_speed = SAS_LINK_RATE_UNKNOWN;
+
+	/* Create the SIGNATURE FIS Timeout timer for this phy */
+	sci_init_timer(&iphy->sata_timer, phy_sata_timeout);
+}
+
+void isci_phy_init(struct isci_phy *iphy, struct isci_host *ihost, int index)
+{
+	struct sci_oem_params *oem = &ihost->oem_parameters;
+	u64 sci_sas_addr;
+	__be64 sas_addr;
+
+	sci_sas_addr = oem->phys[index].sas_address.high;
+	sci_sas_addr <<= 32;
+	sci_sas_addr |= oem->phys[index].sas_address.low;
+	sas_addr = cpu_to_be64(sci_sas_addr);
+	memcpy(iphy->sas_addr, &sas_addr, sizeof(sas_addr));
+
+	iphy->sas_phy.enabled = 0;
+	iphy->sas_phy.id = index;
+	iphy->sas_phy.sas_addr = &iphy->sas_addr[0];
+	iphy->sas_phy.frame_rcvd = (u8 *)&iphy->frame_rcvd;
+	iphy->sas_phy.ha = &ihost->sas_ha;
+	iphy->sas_phy.lldd_phy = iphy;
+	iphy->sas_phy.enabled = 1;
+	iphy->sas_phy.iproto = SAS_PROTOCOL_ALL;
+	iphy->sas_phy.tproto = 0;
+	iphy->sas_phy.role = PHY_ROLE_INITIATOR;
+	iphy->sas_phy.oob_mode = OOB_NOT_CONNECTED;
+	iphy->sas_phy.linkrate = SAS_LINK_RATE_UNKNOWN;
+	memset(&iphy->frame_rcvd, 0, sizeof(iphy->frame_rcvd));
+}
+
+
+/**
+ * isci_phy_control() - This function is one of the SAS Domain Template
+ *    functions. This is a phy management function.
+ * @sas_phy: This parameter specifies the sphy being controlled.
+ * @func: This parameter specifies the phy control function being invoked.
+ * @buf: This parameter is specific to the phy function being invoked.
+ *
+ * status, zero indicates success.
+ */
+int isci_phy_control(struct asd_sas_phy *sas_phy,
+		     enum phy_func func,
+		     void *buf)
+{
+	int ret = 0;
+	struct isci_phy *iphy = sas_phy->lldd_phy;
+	struct asd_sas_port *port = sas_phy->port;
+	struct isci_host *ihost = sas_phy->ha->lldd_ha;
+	unsigned long flags;
+
+	dev_dbg(&ihost->pdev->dev,
+		"%s: phy %p; func %d; buf %p; isci phy %p, port %p\n",
+		__func__, sas_phy, func, buf, iphy, port);
+
+	switch (func) {
+	case PHY_FUNC_DISABLE:
+		spin_lock_irqsave(&ihost->scic_lock, flags);
+		scu_link_layer_start_oob(iphy);
+		sci_phy_stop(iphy);
+		spin_unlock_irqrestore(&ihost->scic_lock, flags);
+		break;
+
+	case PHY_FUNC_LINK_RESET:
+		spin_lock_irqsave(&ihost->scic_lock, flags);
+		scu_link_layer_start_oob(iphy);
+		sci_phy_stop(iphy);
+		sci_phy_start(iphy);
+		spin_unlock_irqrestore(&ihost->scic_lock, flags);
+		break;
+
+	case PHY_FUNC_HARD_RESET:
+		if (!port)
+			return -ENODEV;
+
+		ret = isci_port_perform_hard_reset(ihost, port->lldd_port, iphy);
+
+		break;
+	case PHY_FUNC_GET_EVENTS: {
+		struct scu_link_layer_registers __iomem *r;
+		struct sas_phy *phy = sas_phy->phy;
+
+		r = iphy->link_layer_registers;
+		phy->running_disparity_error_count = readl(&r->running_disparity_error_count);
+		phy->loss_of_dword_sync_count = readl(&r->loss_of_sync_error_count);
+		phy->phy_reset_problem_count = readl(&r->phy_reset_problem_count);
+		phy->invalid_dword_count = readl(&r->invalid_dword_counter);
+		break;
+	}
+
+	default:
+		dev_dbg(&ihost->pdev->dev,
+			   "%s: phy %p; func %d NOT IMPLEMENTED!\n",
+			   __func__, sas_phy, func);
+		ret = -ENOSYS;
+		break;
+	}
+	return ret;
+}