Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 673 insertions, 0 deletions

diff --git a/drivers/thermal/tegra/tegra30-tsensor.c b/drivers/thermal/tegra/tegra30-tsensor.c
new file mode 100644
index 0000000000..d911fa60f1
--- /dev/null
+++ b/drivers/thermal/tegra/tegra30-tsensor.c
@@ -0,0 +1,673 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Tegra30 SoC Thermal Sensor driver
+ *
+ * Based on downstream HWMON driver from NVIDIA.
+ * Copyright (C) 2011 NVIDIA Corporation
+ *
+ * Author: Dmitry Osipenko <digetx@gmail.com>
+ * Copyright (C) 2021 GRATE-DRIVER project
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/math.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+#include <linux/thermal.h>
+#include <linux/types.h>
+
+#include <soc/tegra/fuse.h>
+
+#include "../thermal_hwmon.h"
+
+#define TSENSOR_SENSOR0_CONFIG0				0x0
+#define TSENSOR_SENSOR0_CONFIG0_SENSOR_STOP		BIT(0)
+#define TSENSOR_SENSOR0_CONFIG0_HW_FREQ_DIV_EN		BIT(1)
+#define TSENSOR_SENSOR0_CONFIG0_THERMAL_RST_EN		BIT(2)
+#define TSENSOR_SENSOR0_CONFIG0_DVFS_EN			BIT(3)
+#define TSENSOR_SENSOR0_CONFIG0_INTR_OVERFLOW_EN	BIT(4)
+#define TSENSOR_SENSOR0_CONFIG0_INTR_HW_FREQ_DIV_EN	BIT(5)
+#define TSENSOR_SENSOR0_CONFIG0_INTR_THERMAL_RST_EN	BIT(6)
+#define TSENSOR_SENSOR0_CONFIG0_M			GENMASK(23,  8)
+#define TSENSOR_SENSOR0_CONFIG0_N			GENMASK(31, 24)
+
+#define TSENSOR_SENSOR0_CONFIG1				0x8
+#define TSENSOR_SENSOR0_CONFIG1_TH1			GENMASK(15,  0)
+#define TSENSOR_SENSOR0_CONFIG1_TH2			GENMASK(31, 16)
+
+#define TSENSOR_SENSOR0_CONFIG2				0xc
+#define TSENSOR_SENSOR0_CONFIG2_TH3			GENMASK(15,  0)
+
+#define TSENSOR_SENSOR0_STATUS0				0x18
+#define TSENSOR_SENSOR0_STATUS0_STATE			GENMASK(2, 0)
+#define TSENSOR_SENSOR0_STATUS0_INTR			BIT(8)
+#define TSENSOR_SENSOR0_STATUS0_CURRENT_VALID		BIT(9)
+
+#define TSENSOR_SENSOR0_TS_STATUS1			0x1c
+#define TSENSOR_SENSOR0_TS_STATUS1_CURRENT_COUNT	GENMASK(31, 16)
+
+#define TEGRA30_FUSE_TEST_PROG_VER			0x28
+
+#define TEGRA30_FUSE_TSENSOR_CALIB			0x98
+#define TEGRA30_FUSE_TSENSOR_CALIB_LOW			GENMASK(15,  0)
+#define TEGRA30_FUSE_TSENSOR_CALIB_HIGH			GENMASK(31, 16)
+
+#define TEGRA30_FUSE_SPARE_BIT				0x144
+
+struct tegra_tsensor;
+
+struct tegra_tsensor_calibration_data {
+	int a, b, m, n, p, r;
+};
+
+struct tegra_tsensor_channel {
+	void __iomem *regs;
+	unsigned int id;
+	struct tegra_tsensor *ts;
+	struct thermal_zone_device *tzd;
+};
+
+struct tegra_tsensor {
+	void __iomem *regs;
+	bool swap_channels;
+	struct clk *clk;
+	struct device *dev;
+	struct reset_control *rst;
+	struct tegra_tsensor_channel ch[2];
+	struct tegra_tsensor_calibration_data calib;
+};
+
+static int tegra_tsensor_hw_enable(const struct tegra_tsensor *ts)
+{
+	u32 val;
+	int err;
+
+	err = reset_control_assert(ts->rst);
+	if (err) {
+		dev_err(ts->dev, "failed to assert hardware reset: %d\n", err);
+		return err;
+	}
+
+	err = clk_prepare_enable(ts->clk);
+	if (err) {
+		dev_err(ts->dev, "failed to enable clock: %d\n", err);
+		return err;
+	}
+
+	fsleep(1000);
+
+	err = reset_control_deassert(ts->rst);
+	if (err) {
+		dev_err(ts->dev, "failed to deassert hardware reset: %d\n", err);
+		goto disable_clk;
+	}
+
+	/*
+	 * Sensors are enabled after reset by default, but not gauging
+	 * until clock counter is programmed.
+	 *
+	 * M: number of reference clock pulses after which every
+	 *    temperature / voltage measurement is made
+	 *
+	 * N: number of reference clock counts for which the counter runs
+	 */
+	val  = FIELD_PREP(TSENSOR_SENSOR0_CONFIG0_M, 12500);
+	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG0_N, 255);
+
+	/* apply the same configuration to both channels */
+	writel_relaxed(val, ts->regs + 0x40 + TSENSOR_SENSOR0_CONFIG0);
+	writel_relaxed(val, ts->regs + 0x80 + TSENSOR_SENSOR0_CONFIG0);
+
+	return 0;
+
+disable_clk:
+	clk_disable_unprepare(ts->clk);
+
+	return err;
+}
+
+static int tegra_tsensor_hw_disable(const struct tegra_tsensor *ts)
+{
+	int err;
+
+	err = reset_control_assert(ts->rst);
+	if (err) {
+		dev_err(ts->dev, "failed to assert hardware reset: %d\n", err);
+		return err;
+	}
+
+	clk_disable_unprepare(ts->clk);
+
+	return 0;
+}
+
+static void devm_tegra_tsensor_hw_disable(void *data)
+{
+	const struct tegra_tsensor *ts = data;
+
+	tegra_tsensor_hw_disable(ts);
+}
+
+static int tegra_tsensor_get_temp(struct thermal_zone_device *tz, int *temp)
+{
+	const struct tegra_tsensor_channel *tsc = thermal_zone_device_priv(tz);
+	const struct tegra_tsensor *ts = tsc->ts;
+	int err, c1, c2, c3, c4, counter;
+	u32 val;
+
+	/*
+	 * Counter will be invalid if hardware is misprogrammed or not enough
+	 * time passed since the time when sensor was enabled.
+	 */
+	err = readl_relaxed_poll_timeout(tsc->regs + TSENSOR_SENSOR0_STATUS0, val,
+					 val & TSENSOR_SENSOR0_STATUS0_CURRENT_VALID,
+					 21 * USEC_PER_MSEC,
+					 21 * USEC_PER_MSEC * 50);
+	if (err) {
+		dev_err_once(ts->dev, "ch%u: counter invalid\n", tsc->id);
+		return err;
+	}
+
+	val = readl_relaxed(tsc->regs + TSENSOR_SENSOR0_TS_STATUS1);
+	counter = FIELD_GET(TSENSOR_SENSOR0_TS_STATUS1_CURRENT_COUNT, val);
+
+	/*
+	 * This shouldn't happen with a valid counter status, nevertheless
+	 * lets verify the value since it's in a separate (from status)
+	 * register.
+	 */
+	if (counter == 0xffff) {
+		dev_err_once(ts->dev, "ch%u: counter overflow\n", tsc->id);
+		return -EINVAL;
+	}
+
+	/*
+	 * temperature = a * counter + b
+	 * temperature = m * (temperature ^ 2) + n * temperature + p
+	 */
+	c1 = DIV_ROUND_CLOSEST(ts->calib.a * counter + ts->calib.b, 1000000);
+	c1 = c1 ?: 1;
+	c2 = DIV_ROUND_CLOSEST(ts->calib.p, c1);
+	c3 = c1 * ts->calib.m;
+	c4 = ts->calib.n;
+
+	*temp = DIV_ROUND_CLOSEST(c1 * (c2 + c3 + c4), 1000);
+
+	return 0;
+}
+
+static int tegra_tsensor_temp_to_counter(const struct tegra_tsensor *ts, int temp)
+{
+	int c1, c2;
+
+	c1 = DIV_ROUND_CLOSEST(ts->calib.p - temp * 1000, ts->calib.m);
+	c2 = -ts->calib.r - int_sqrt(ts->calib.r * ts->calib.r - c1);
+
+	return DIV_ROUND_CLOSEST(c2 * 1000000 - ts->calib.b, ts->calib.a);
+}
+
+static int tegra_tsensor_set_trips(struct thermal_zone_device *tz, int low, int high)
+{
+	const struct tegra_tsensor_channel *tsc = thermal_zone_device_priv(tz);
+	const struct tegra_tsensor *ts = tsc->ts;
+	u32 val;
+
+	/*
+	 * TSENSOR doesn't trigger interrupt on the "low" temperature breach,
+	 * hence bail out if high temperature is unspecified.
+	 */
+	if (high == INT_MAX)
+		return 0;
+
+	val = readl_relaxed(tsc->regs + TSENSOR_SENSOR0_CONFIG1);
+	val &= ~TSENSOR_SENSOR0_CONFIG1_TH1;
+
+	high = tegra_tsensor_temp_to_counter(ts, high);
+	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG1_TH1, high);
+	writel_relaxed(val, tsc->regs + TSENSOR_SENSOR0_CONFIG1);
+
+	return 0;
+}
+
+static const struct thermal_zone_device_ops ops = {
+	.get_temp = tegra_tsensor_get_temp,
+	.set_trips = tegra_tsensor_set_trips,
+};
+
+static bool
+tegra_tsensor_handle_channel_interrupt(const struct tegra_tsensor *ts,
+				       unsigned int id)
+{
+	const struct tegra_tsensor_channel *tsc = &ts->ch[id];
+	u32 val;
+
+	val = readl_relaxed(tsc->regs + TSENSOR_SENSOR0_STATUS0);
+	writel_relaxed(val, tsc->regs + TSENSOR_SENSOR0_STATUS0);
+
+	if (FIELD_GET(TSENSOR_SENSOR0_STATUS0_STATE, val) == 5)
+		dev_err_ratelimited(ts->dev, "ch%u: counter overflowed\n", id);
+
+	if (!FIELD_GET(TSENSOR_SENSOR0_STATUS0_INTR, val))
+		return false;
+
+	thermal_zone_device_update(tsc->tzd, THERMAL_EVENT_UNSPECIFIED);
+
+	return true;
+}
+
+static irqreturn_t tegra_tsensor_isr(int irq, void *data)
+{
+	const struct tegra_tsensor *ts = data;
+	bool handled = false;
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(ts->ch); i++)
+		handled |= tegra_tsensor_handle_channel_interrupt(ts, i);
+
+	return handled ? IRQ_HANDLED : IRQ_NONE;
+}
+
+static int tegra_tsensor_disable_hw_channel(const struct tegra_tsensor *ts,
+					    unsigned int id)
+{
+	const struct tegra_tsensor_channel *tsc = &ts->ch[id];
+	struct thermal_zone_device *tzd = tsc->tzd;
+	u32 val;
+	int err;
+
+	if (!tzd)
+		goto stop_channel;
+
+	err = thermal_zone_device_disable(tzd);
+	if (err) {
+		dev_err(ts->dev, "ch%u: failed to disable zone: %d\n", id, err);
+		return err;
+	}
+
+stop_channel:
+	/* stop channel gracefully */
+	val = readl_relaxed(tsc->regs + TSENSOR_SENSOR0_CONFIG0);
+	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG0_SENSOR_STOP, 1);
+	writel_relaxed(val, tsc->regs + TSENSOR_SENSOR0_CONFIG0);
+
+	return 0;
+}
+
+static void tegra_tsensor_get_hw_channel_trips(struct thermal_zone_device *tzd,
+					       int *hot_trip, int *crit_trip)
+{
+	unsigned int i;
+
+	/*
+	 * 90C is the maximal critical temperature of all Tegra30 SoC variants,
+	 * use it for the default trip if unspecified in a device-tree.
+	 */
+	*hot_trip  = 85000;
+	*crit_trip = 90000;
+
+	for (i = 0; i < thermal_zone_get_num_trips(tzd); i++) {
+
+		struct thermal_trip trip;
+
+		thermal_zone_get_trip(tzd, i, &trip);
+
+		if (trip.type == THERMAL_TRIP_HOT)
+			*hot_trip = trip.temperature;
+
+		if (trip.type == THERMAL_TRIP_CRITICAL)
+			*crit_trip = trip.temperature;
+	}
+
+	/* clamp hardware trips to the calibration limits */
+	*hot_trip = clamp(*hot_trip, 25000, 90000);
+
+	/*
+	 * Kernel will perform a normal system shut down if it will
+	 * see that critical temperature is breached, hence set the
+	 * hardware limit by 5C higher in order to allow system to
+	 * shut down gracefully before sending signal to the Power
+	 * Management controller.
+	 */
+	*crit_trip = clamp(*crit_trip + 5000, 25000, 90000);
+}
+
+static int tegra_tsensor_enable_hw_channel(const struct tegra_tsensor *ts,
+					   unsigned int id)
+{
+	const struct tegra_tsensor_channel *tsc = &ts->ch[id];
+	struct thermal_zone_device *tzd = tsc->tzd;
+	int err, hot_trip = 0, crit_trip = 0;
+	u32 val;
+
+	if (!tzd) {
+		val = readl_relaxed(tsc->regs + TSENSOR_SENSOR0_CONFIG0);
+		val &= ~TSENSOR_SENSOR0_CONFIG0_SENSOR_STOP;
+		writel_relaxed(val, tsc->regs + TSENSOR_SENSOR0_CONFIG0);
+
+		return 0;
+	}
+
+	tegra_tsensor_get_hw_channel_trips(tzd, &hot_trip, &crit_trip);
+
+	dev_info_once(ts->dev, "ch%u: PMC emergency shutdown trip set to %dC\n",
+		      id, DIV_ROUND_CLOSEST(crit_trip, 1000));
+
+	hot_trip  = tegra_tsensor_temp_to_counter(ts, hot_trip);
+	crit_trip = tegra_tsensor_temp_to_counter(ts, crit_trip);
+
+	/* program LEVEL2 counter threshold */
+	val = readl_relaxed(tsc->regs + TSENSOR_SENSOR0_CONFIG1);
+	val &= ~TSENSOR_SENSOR0_CONFIG1_TH2;
+	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG1_TH2, hot_trip);
+	writel_relaxed(val, tsc->regs + TSENSOR_SENSOR0_CONFIG1);
+
+	/* program LEVEL3 counter threshold */
+	val = readl_relaxed(tsc->regs + TSENSOR_SENSOR0_CONFIG2);
+	val &= ~TSENSOR_SENSOR0_CONFIG2_TH3;
+	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG2_TH3, crit_trip);
+	writel_relaxed(val, tsc->regs + TSENSOR_SENSOR0_CONFIG2);
+
+	/*
+	 * Enable sensor, emergency shutdown, interrupts for level 1/2/3
+	 * breaches and counter overflow condition.
+	 *
+	 * Disable DIV2 throttle for now since we need to figure out how
+	 * to integrate it properly with the thermal framework.
+	 *
+	 * Thermal levels supported by hardware:
+	 *
+	 *     Level 0 = cold
+	 *     Level 1 = passive cooling (cpufreq DVFS)
+	 *     Level 2 = passive cooling assisted by hardware (DIV2)
+	 *     Level 3 = emergency shutdown assisted by hardware (PMC)
+	 */
+	val = readl_relaxed(tsc->regs + TSENSOR_SENSOR0_CONFIG0);
+	val &= ~TSENSOR_SENSOR0_CONFIG0_SENSOR_STOP;
+	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG0_DVFS_EN, 1);
+	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG0_HW_FREQ_DIV_EN, 0);
+	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG0_THERMAL_RST_EN, 1);
+	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG0_INTR_OVERFLOW_EN, 1);
+	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG0_INTR_HW_FREQ_DIV_EN, 1);
+	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG0_INTR_THERMAL_RST_EN, 1);
+	writel_relaxed(val, tsc->regs + TSENSOR_SENSOR0_CONFIG0);
+
+	err = thermal_zone_device_enable(tzd);
+	if (err) {
+		dev_err(ts->dev, "ch%u: failed to enable zone: %d\n", id, err);
+		return err;
+	}
+
+	return 0;
+}
+
+static bool tegra_tsensor_fuse_read_spare(unsigned int spare)
+{
+	u32 val = 0;
+
+	tegra_fuse_readl(TEGRA30_FUSE_SPARE_BIT + spare * 4, &val);
+
+	return !!val;
+}
+
+static int tegra_tsensor_nvmem_setup(struct tegra_tsensor *ts)
+{
+	u32 i, ate_ver = 0, cal = 0, t1_25C = 0, t2_90C = 0;
+	int err, c1_25C, c2_90C;
+
+	err = tegra_fuse_readl(TEGRA30_FUSE_TEST_PROG_VER, &ate_ver);
+	if (err) {
+		dev_err_probe(ts->dev, err, "failed to get ATE version\n");
+		return err;
+	}
+
+	if (ate_ver < 8) {
+		dev_info(ts->dev, "unsupported ATE version: %u\n", ate_ver);
+		return -ENODEV;
+	}
+
+	/*
+	 * We have two TSENSOR channels in a two different spots on SoC.
+	 * Second channel provides more accurate data on older SoC versions,
+	 * use it as a primary channel.
+	 */
+	if (ate_ver <= 21) {
+		dev_info_once(ts->dev,
+			      "older ATE version detected, channels remapped\n");
+		ts->swap_channels = true;
+	}
+
+	err = tegra_fuse_readl(TEGRA30_FUSE_TSENSOR_CALIB, &cal);
+	if (err) {
+		dev_err(ts->dev, "failed to get calibration data: %d\n", err);
+		return err;
+	}
+
+	/* get calibrated counter values for 25C/90C thresholds */
+	c1_25C = FIELD_GET(TEGRA30_FUSE_TSENSOR_CALIB_LOW, cal);
+	c2_90C = FIELD_GET(TEGRA30_FUSE_TSENSOR_CALIB_HIGH, cal);
+
+	/* and calibrated temperatures corresponding to the counter values */
+	for (i = 0; i < 7; i++) {
+		t1_25C |= tegra_tsensor_fuse_read_spare(14 + i) << i;
+		t1_25C |= tegra_tsensor_fuse_read_spare(21 + i) << i;
+
+		t2_90C |= tegra_tsensor_fuse_read_spare(0 + i) << i;
+		t2_90C |= tegra_tsensor_fuse_read_spare(7 + i) << i;
+	}
+
+	if (c2_90C - c1_25C <= t2_90C - t1_25C) {
+		dev_err(ts->dev, "invalid calibration data: %d %d %u %u\n",
+			c2_90C, c1_25C, t2_90C, t1_25C);
+		return -EINVAL;
+	}
+
+	/* all calibration coefficients are premultiplied by 1000000 */
+
+	ts->calib.a = DIV_ROUND_CLOSEST((t2_90C - t1_25C) * 1000000,
+					(c2_90C - c1_25C));
+
+	ts->calib.b = t1_25C * 1000000 - ts->calib.a * c1_25C;
+
+	if (tegra_sku_info.revision == TEGRA_REVISION_A01) {
+		ts->calib.m =     -2775;
+		ts->calib.n =   1338811;
+		ts->calib.p =  -7300000;
+	} else {
+		ts->calib.m =     -3512;
+		ts->calib.n =   1528943;
+		ts->calib.p = -11100000;
+	}
+
+	/* except the coefficient of a reduced quadratic equation */
+	ts->calib.r = DIV_ROUND_CLOSEST(ts->calib.n, ts->calib.m * 2);
+
+	dev_info_once(ts->dev,
+		      "calibration: %d %d %u %u ATE ver: %u SoC rev: %u\n",
+		      c2_90C, c1_25C, t2_90C, t1_25C, ate_ver,
+		      tegra_sku_info.revision);
+
+	return 0;
+}
+
+static int tegra_tsensor_register_channel(struct tegra_tsensor *ts,
+					  unsigned int id)
+{
+	struct tegra_tsensor_channel *tsc = &ts->ch[id];
+	unsigned int hw_id = ts->swap_channels ? !id : id;
+
+	tsc->ts = ts;
+	tsc->id = id;
+	tsc->regs = ts->regs + 0x40 * (hw_id + 1);
+
+	tsc->tzd = devm_thermal_of_zone_register(ts->dev, id, tsc, &ops);
+	if (IS_ERR(tsc->tzd)) {
+		if (PTR_ERR(tsc->tzd) != -ENODEV)
+			return dev_err_probe(ts->dev, PTR_ERR(tsc->tzd),
+					     "failed to register thermal zone\n");
+
+		/*
+		 * It's okay if sensor isn't assigned to any thermal zone
+		 * in a device-tree.
+		 */
+		tsc->tzd = NULL;
+		return 0;
+	}
+
+	devm_thermal_add_hwmon_sysfs(ts->dev, tsc->tzd);
+
+	return 0;
+}
+
+static int tegra_tsensor_probe(struct platform_device *pdev)
+{
+	struct tegra_tsensor *ts;
+	unsigned int i;
+	int err, irq;
+
+	ts = devm_kzalloc(&pdev->dev, sizeof(*ts), GFP_KERNEL);
+	if (!ts)
+		return -ENOMEM;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	ts->dev = &pdev->dev;
+	platform_set_drvdata(pdev, ts);
+
+	ts->regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(ts->regs))
+		return PTR_ERR(ts->regs);
+
+	ts->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(ts->clk))
+		return dev_err_probe(&pdev->dev, PTR_ERR(ts->clk),
+				     "failed to get clock\n");
+
+	ts->rst = devm_reset_control_get_exclusive(&pdev->dev, NULL);
+	if (IS_ERR(ts->rst))
+		return dev_err_probe(&pdev->dev, PTR_ERR(ts->rst),
+				     "failed to get reset control\n");
+
+	err = tegra_tsensor_nvmem_setup(ts);
+	if (err)
+		return err;
+
+	err = tegra_tsensor_hw_enable(ts);
+	if (err)
+		return err;
+
+	err = devm_add_action_or_reset(&pdev->dev,
+				       devm_tegra_tsensor_hw_disable,
+				       ts);
+	if (err)
+		return err;
+
+	for (i = 0; i < ARRAY_SIZE(ts->ch); i++) {
+		err = tegra_tsensor_register_channel(ts, i);
+		if (err)
+			return err;
+	}
+
+	/*
+	 * Enable the channels before setting the interrupt so
+	 * set_trips() can not be called while we are setting up the
+	 * register TSENSOR_SENSOR0_CONFIG1. With this we close a
+	 * potential race window where we are setting up the TH2 and
+	 * the temperature hits TH1 resulting to an update of the
+	 * TSENSOR_SENSOR0_CONFIG1 register in the ISR.
+	 */
+	for (i = 0; i < ARRAY_SIZE(ts->ch); i++) {
+		err = tegra_tsensor_enable_hw_channel(ts, i);
+		if (err)
+			return err;
+	}
+
+	err = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+					tegra_tsensor_isr, IRQF_ONESHOT,
+					"tegra_tsensor", ts);
+	if (err)
+		return dev_err_probe(&pdev->dev, err,
+				     "failed to request interrupt\n");
+
+	return 0;
+}
+
+static int __maybe_unused tegra_tsensor_suspend(struct device *dev)
+{
+	struct tegra_tsensor *ts = dev_get_drvdata(dev);
+	unsigned int i;
+	int err;
+
+	for (i = 0; i < ARRAY_SIZE(ts->ch); i++) {
+		err = tegra_tsensor_disable_hw_channel(ts, i);
+		if (err)
+			goto enable_channel;
+	}
+
+	err = tegra_tsensor_hw_disable(ts);
+	if (err)
+		goto enable_channel;
+
+	return 0;
+
+enable_channel:
+	while (i--)
+		tegra_tsensor_enable_hw_channel(ts, i);
+
+	return err;
+}
+
+static int __maybe_unused tegra_tsensor_resume(struct device *dev)
+{
+	struct tegra_tsensor *ts = dev_get_drvdata(dev);
+	unsigned int i;
+	int err;
+
+	err = tegra_tsensor_hw_enable(ts);
+	if (err)
+		return err;
+
+	for (i = 0; i < ARRAY_SIZE(ts->ch); i++) {
+		err = tegra_tsensor_enable_hw_channel(ts, i);
+		if (err)
+			return err;
+	}
+
+	return 0;
+}
+
+static const struct dev_pm_ops tegra_tsensor_pm_ops = {
+	SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(tegra_tsensor_suspend,
+				      tegra_tsensor_resume)
+};
+
+static const struct of_device_id tegra_tsensor_of_match[] = {
+	{ .compatible = "nvidia,tegra30-tsensor", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, tegra_tsensor_of_match);
+
+static struct platform_driver tegra_tsensor_driver = {
+	.probe = tegra_tsensor_probe,
+	.driver = {
+		.name = "tegra30-tsensor",
+		.of_match_table = tegra_tsensor_of_match,
+		.pm = &tegra_tsensor_pm_ops,
+	},
+};
+module_platform_driver(tegra_tsensor_driver);
+
+MODULE_DESCRIPTION("NVIDIA Tegra30 Thermal Sensor driver");
+MODULE_AUTHOR("Dmitry Osipenko <digetx@gmail.com>");
+MODULE_LICENSE("GPL");