Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 545 insertions, 0 deletions

diff --git a/drivers/usb/dwc3/dwc3-octeon.c b/drivers/usb/dwc3/dwc3-octeon.c
new file mode 100644
index 0000000000..6010135e1a
--- /dev/null
+++ b/drivers/usb/dwc3/dwc3-octeon.c
@@ -0,0 +1,545 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * DWC3 glue for Cavium Octeon III SOCs.
+ *
+ * Copyright (C) 2010-2017 Cavium Networks
+ * Copyright (C) 2023 RACOM s.r.o.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+/*
+ * USB Control Register
+ */
+#define USBDRD_UCTL_CTL				0x00
+/* BIST fast-clear mode select. A BIST run with this bit set
+ * clears all entries in USBH RAMs to 0x0.
+ */
+# define USBDRD_UCTL_CTL_CLEAR_BIST		BIT_ULL(63)
+/* 1 = Start BIST and cleared by hardware */
+# define USBDRD_UCTL_CTL_START_BIST		BIT_ULL(62)
+/* Reference clock select for SuperSpeed and HighSpeed PLLs:
+ *	0x0 = Both PLLs use DLMC_REF_CLK0 for reference clock
+ *	0x1 = Both PLLs use DLMC_REF_CLK1 for reference clock
+ *	0x2 = SuperSpeed PLL uses DLMC_REF_CLK0 for reference clock &
+ *	      HighSpeed PLL uses PLL_REF_CLK for reference clck
+ *	0x3 = SuperSpeed PLL uses DLMC_REF_CLK1 for reference clock &
+ *	      HighSpeed PLL uses PLL_REF_CLK for reference clck
+ */
+# define USBDRD_UCTL_CTL_REF_CLK_SEL		GENMASK_ULL(61, 60)
+/* 1 = Spread-spectrum clock enable, 0 = SS clock disable */
+# define USBDRD_UCTL_CTL_SSC_EN			BIT_ULL(59)
+/* Spread-spectrum clock modulation range:
+ *	0x0 = -4980 ppm downspread
+ *	0x1 = -4492 ppm downspread
+ *	0x2 = -4003 ppm downspread
+ *	0x3 - 0x7 = Reserved
+ */
+# define USBDRD_UCTL_CTL_SSC_RANGE		GENMASK_ULL(58, 56)
+/* Enable non-standard oscillator frequencies:
+ *	[55:53] = modules -1
+ *	[52:47] = 2's complement push amount, 0 = Feature disabled
+ */
+# define USBDRD_UCTL_CTL_SSC_REF_CLK_SEL	GENMASK_ULL(55, 47)
+/* Reference clock multiplier for non-standard frequencies:
+ *	0x19 = 100MHz on DLMC_REF_CLK* if REF_CLK_SEL = 0x0 or 0x1
+ *	0x28 = 125MHz on DLMC_REF_CLK* if REF_CLK_SEL = 0x0 or 0x1
+ *	0x32 =  50MHz on DLMC_REF_CLK* if REF_CLK_SEL = 0x0 or 0x1
+ *	Other Values = Reserved
+ */
+# define USBDRD_UCTL_CTL_MPLL_MULTIPLIER	GENMASK_ULL(46, 40)
+/* Enable reference clock to prescaler for SuperSpeed functionality.
+ * Should always be set to "1"
+ */
+# define USBDRD_UCTL_CTL_REF_SSP_EN		BIT_ULL(39)
+/* Divide the reference clock by 2 before entering the
+ * REF_CLK_FSEL divider:
+ *	If REF_CLK_SEL = 0x0 or 0x1, then only 0x0 is legal
+ *	If REF_CLK_SEL = 0x2 or 0x3, then:
+ *		0x1 = DLMC_REF_CLK* is 125MHz
+ *		0x0 = DLMC_REF_CLK* is another supported frequency
+ */
+# define USBDRD_UCTL_CTL_REF_CLK_DIV2		BIT_ULL(38)
+/* Select reference clock freqnuency for both PLL blocks:
+ *	0x27 = REF_CLK_SEL is 0x0 or 0x1
+ *	0x07 = REF_CLK_SEL is 0x2 or 0x3
+ */
+# define USBDRD_UCTL_CTL_REF_CLK_FSEL		GENMASK_ULL(37, 32)
+/* Controller clock enable. */
+# define USBDRD_UCTL_CTL_H_CLK_EN		BIT_ULL(30)
+/* Select bypass input to controller clock divider:
+ *	0x0 = Use divided coprocessor clock from H_CLKDIV
+ *	0x1 = Use clock from GPIO pins
+ */
+# define USBDRD_UCTL_CTL_H_CLK_BYP_SEL		BIT_ULL(29)
+/* Reset controller clock divider. */
+# define USBDRD_UCTL_CTL_H_CLKDIV_RST		BIT_ULL(28)
+/* Clock divider select:
+ *	0x0 = divide by 1
+ *	0x1 = divide by 2
+ *	0x2 = divide by 4
+ *	0x3 = divide by 6
+ *	0x4 = divide by 8
+ *	0x5 = divide by 16
+ *	0x6 = divide by 24
+ *	0x7 = divide by 32
+ */
+# define USBDRD_UCTL_CTL_H_CLKDIV_SEL		GENMASK_ULL(26, 24)
+/* USB3 port permanently attached: 0x0 = No, 0x1 = Yes */
+# define USBDRD_UCTL_CTL_USB3_PORT_PERM_ATTACH	BIT_ULL(21)
+/* USB2 port permanently attached: 0x0 = No, 0x1 = Yes */
+# define USBDRD_UCTL_CTL_USB2_PORT_PERM_ATTACH	BIT_ULL(20)
+/* Disable SuperSpeed PHY: 0x0 = No, 0x1 = Yes */
+# define USBDRD_UCTL_CTL_USB3_PORT_DISABLE	BIT_ULL(18)
+/* Disable HighSpeed PHY: 0x0 = No, 0x1 = Yes */
+# define USBDRD_UCTL_CTL_USB2_PORT_DISABLE	BIT_ULL(16)
+/* Enable PHY SuperSpeed block power: 0x0 = No, 0x1 = Yes */
+# define USBDRD_UCTL_CTL_SS_POWER_EN		BIT_ULL(14)
+/* Enable PHY HighSpeed block power: 0x0 = No, 0x1 = Yes */
+# define USBDRD_UCTL_CTL_HS_POWER_EN		BIT_ULL(12)
+/* Enable USB UCTL interface clock: 0xx = No, 0x1 = Yes */
+# define USBDRD_UCTL_CTL_CSCLK_EN		BIT_ULL(4)
+/* Controller mode: 0x0 = Host, 0x1 = Device */
+# define USBDRD_UCTL_CTL_DRD_MODE		BIT_ULL(3)
+/* PHY reset */
+# define USBDRD_UCTL_CTL_UPHY_RST		BIT_ULL(2)
+/* Software reset UAHC */
+# define USBDRD_UCTL_CTL_UAHC_RST		BIT_ULL(1)
+/* Software resets UCTL */
+# define USBDRD_UCTL_CTL_UCTL_RST		BIT_ULL(0)
+
+#define USBDRD_UCTL_BIST_STATUS			0x08
+#define USBDRD_UCTL_SPARE0			0x10
+#define USBDRD_UCTL_INTSTAT			0x30
+#define USBDRD_UCTL_PORT_CFG_HS(port)		(0x40 + (0x20 * port))
+#define USBDRD_UCTL_PORT_CFG_SS(port)		(0x48 + (0x20 * port))
+#define USBDRD_UCTL_PORT_CR_DBG_CFG(port)	(0x50 + (0x20 * port))
+#define USBDRD_UCTL_PORT_CR_DBG_STATUS(port)	(0x58 + (0x20 * port))
+
+/*
+ * UCTL Configuration Register
+ */
+#define USBDRD_UCTL_HOST_CFG			0xe0
+/* Indicates minimum value of all received BELT values */
+# define USBDRD_UCTL_HOST_CFG_HOST_CURRENT_BELT	GENMASK_ULL(59, 48)
+/* HS jitter adjustment */
+# define USBDRD_UCTL_HOST_CFG_FLA		GENMASK_ULL(37, 32)
+/* Bus-master enable: 0x0 = Disabled (stall DMAs), 0x1 = enabled */
+# define USBDRD_UCTL_HOST_CFG_BME		BIT_ULL(28)
+/* Overcurrent protection enable: 0x0 = unavailable, 0x1 = available */
+# define USBDRD_UCTL_HOST_OCI_EN		BIT_ULL(27)
+/* Overcurrent sene selection:
+ *	0x0 = Overcurrent indication from off-chip is active-low
+ *	0x1 = Overcurrent indication from off-chip is active-high
+ */
+# define USBDRD_UCTL_HOST_OCI_ACTIVE_HIGH_EN	BIT_ULL(26)
+/* Port power control enable: 0x0 = unavailable, 0x1 = available */
+# define USBDRD_UCTL_HOST_PPC_EN		BIT_ULL(25)
+/* Port power control sense selection:
+ *	0x0 = Port power to off-chip is active-low
+ *	0x1 = Port power to off-chip is active-high
+ */
+# define USBDRD_UCTL_HOST_PPC_ACTIVE_HIGH_EN	BIT_ULL(24)
+
+/*
+ * UCTL Shim Features Register
+ */
+#define USBDRD_UCTL_SHIM_CFG			0xe8
+/* Out-of-bound UAHC register access: 0 = read, 1 = write */
+# define USBDRD_UCTL_SHIM_CFG_XS_NCB_OOB_WRN	BIT_ULL(63)
+/* SRCID error log for out-of-bound UAHC register access:
+ *	[59:58] = chipID
+ *	[57] = Request source: 0 = core, 1 = NCB-device
+ *	[56:51] = Core/NCB-device number, [56] always 0 for NCB devices
+ *	[50:48] = SubID
+ */
+# define USBDRD_UCTL_SHIM_CFG_XS_NCB_OOB_OSRC	GENMASK_ULL(59, 48)
+/* Error log for bad UAHC DMA access: 0 = Read log, 1 = Write log */
+# define USBDRD_UCTL_SHIM_CFG_XM_BAD_DMA_WRN	BIT_ULL(47)
+/* Encoded error type for bad UAHC DMA */
+# define USBDRD_UCTL_SHIM_CFG_XM_BAD_DMA_TYPE	GENMASK_ULL(43, 40)
+/* Select the IOI read command used by DMA accesses */
+# define USBDRD_UCTL_SHIM_CFG_DMA_READ_CMD	BIT_ULL(12)
+/* Select endian format for DMA accesses to the L2C:
+ *	0x0 = Little endian
+ *	0x1 = Big endian
+ *	0x2 = Reserved
+ *	0x3 = Reserved
+ */
+# define USBDRD_UCTL_SHIM_CFG_DMA_ENDIAN_MODE	GENMASK_ULL(9, 8)
+/* Select endian format for IOI CSR access to UAHC:
+ *	0x0 = Little endian
+ *	0x1 = Big endian
+ *	0x2 = Reserved
+ *	0x3 = Reserved
+ */
+# define USBDRD_UCTL_SHIM_CFG_CSR_ENDIAN_MODE	GENMASK_ULL(1, 0)
+
+#define USBDRD_UCTL_ECC				0xf0
+#define USBDRD_UCTL_SPARE1			0xf8
+
+struct dwc3_octeon {
+	struct device *dev;
+	void __iomem *base;
+};
+
+#define DWC3_GPIO_POWER_NONE	(-1)
+
+#ifdef CONFIG_CAVIUM_OCTEON_SOC
+#include <asm/octeon/octeon.h>
+static inline uint64_t dwc3_octeon_readq(void __iomem *addr)
+{
+	return cvmx_readq_csr(addr);
+}
+
+static inline void dwc3_octeon_writeq(void __iomem *base, uint64_t val)
+{
+	cvmx_writeq_csr(base, val);
+}
+
+static void dwc3_octeon_config_gpio(int index, int gpio)
+{
+	union cvmx_gpio_bit_cfgx gpio_bit;
+
+	if ((OCTEON_IS_MODEL(OCTEON_CN73XX) ||
+	    OCTEON_IS_MODEL(OCTEON_CNF75XX))
+	    && gpio <= 31) {
+		gpio_bit.u64 = cvmx_read_csr(CVMX_GPIO_BIT_CFGX(gpio));
+		gpio_bit.s.tx_oe = 1;
+		gpio_bit.s.output_sel = (index == 0 ? 0x14 : 0x15);
+		cvmx_write_csr(CVMX_GPIO_BIT_CFGX(gpio), gpio_bit.u64);
+	} else if (gpio <= 15) {
+		gpio_bit.u64 = cvmx_read_csr(CVMX_GPIO_BIT_CFGX(gpio));
+		gpio_bit.s.tx_oe = 1;
+		gpio_bit.s.output_sel = (index == 0 ? 0x14 : 0x19);
+		cvmx_write_csr(CVMX_GPIO_BIT_CFGX(gpio), gpio_bit.u64);
+	} else {
+		gpio_bit.u64 = cvmx_read_csr(CVMX_GPIO_XBIT_CFGX(gpio));
+		gpio_bit.s.tx_oe = 1;
+		gpio_bit.s.output_sel = (index == 0 ? 0x14 : 0x19);
+		cvmx_write_csr(CVMX_GPIO_XBIT_CFGX(gpio), gpio_bit.u64);
+	}
+}
+#else
+static inline uint64_t dwc3_octeon_readq(void __iomem *addr)
+{
+	return 0;
+}
+
+static inline void dwc3_octeon_writeq(void __iomem *base, uint64_t val) { }
+
+static inline void dwc3_octeon_config_gpio(int index, int gpio) { }
+
+static uint64_t octeon_get_io_clock_rate(void)
+{
+	return 150000000;
+}
+#endif
+
+static int dwc3_octeon_get_divider(void)
+{
+	static const uint8_t clk_div[] = { 1, 2, 4, 6, 8, 16, 24, 32 };
+	int div = 0;
+
+	while (div < ARRAY_SIZE(clk_div)) {
+		uint64_t rate = octeon_get_io_clock_rate() / clk_div[div];
+		if (rate <= 300000000 && rate >= 150000000)
+			return div;
+		div++;
+	}
+
+	return -EINVAL;
+}
+
+static int dwc3_octeon_setup(struct dwc3_octeon *octeon,
+			     int ref_clk_sel, int ref_clk_fsel, int mpll_mul,
+			     int power_gpio, int power_active_low)
+{
+	u64 val;
+	int div;
+	struct device *dev = octeon->dev;
+	void __iomem *uctl_ctl_reg = octeon->base + USBDRD_UCTL_CTL;
+	void __iomem *uctl_host_cfg_reg = octeon->base + USBDRD_UCTL_HOST_CFG;
+
+	/*
+	 * Step 1: Wait for all voltages to be stable...that surely
+	 *         happened before starting the kernel. SKIP
+	 */
+
+	/* Step 2: Select GPIO for overcurrent indication, if desired. SKIP */
+
+	/* Step 3: Assert all resets. */
+	val = dwc3_octeon_readq(uctl_ctl_reg);
+	val |= USBDRD_UCTL_CTL_UPHY_RST |
+	       USBDRD_UCTL_CTL_UAHC_RST |
+	       USBDRD_UCTL_CTL_UCTL_RST;
+	dwc3_octeon_writeq(uctl_ctl_reg, val);
+
+	/* Step 4a: Reset the clock dividers. */
+	val = dwc3_octeon_readq(uctl_ctl_reg);
+	val |= USBDRD_UCTL_CTL_H_CLKDIV_RST;
+	dwc3_octeon_writeq(uctl_ctl_reg, val);
+
+	/* Step 4b: Select controller clock frequency. */
+	div = dwc3_octeon_get_divider();
+	if (div < 0) {
+		dev_err(dev, "clock divider invalid\n");
+		return div;
+	}
+	val = dwc3_octeon_readq(uctl_ctl_reg);
+	val &= ~USBDRD_UCTL_CTL_H_CLKDIV_SEL;
+	val |= FIELD_PREP(USBDRD_UCTL_CTL_H_CLKDIV_SEL, div);
+	val |= USBDRD_UCTL_CTL_H_CLK_EN;
+	dwc3_octeon_writeq(uctl_ctl_reg, val);
+	val = dwc3_octeon_readq(uctl_ctl_reg);
+	if ((div != FIELD_GET(USBDRD_UCTL_CTL_H_CLKDIV_SEL, val)) ||
+	    (!(FIELD_GET(USBDRD_UCTL_CTL_H_CLK_EN, val)))) {
+		dev_err(dev, "clock init failure (UCTL_CTL=%016llx)\n", val);
+		return -EINVAL;
+	}
+
+	/* Step 4c: Deassert the controller clock divider reset. */
+	val &= ~USBDRD_UCTL_CTL_H_CLKDIV_RST;
+	dwc3_octeon_writeq(uctl_ctl_reg, val);
+
+	/* Step 5a: Reference clock configuration. */
+	val = dwc3_octeon_readq(uctl_ctl_reg);
+	val &= ~USBDRD_UCTL_CTL_REF_CLK_DIV2;
+	val &= ~USBDRD_UCTL_CTL_REF_CLK_SEL;
+	val |= FIELD_PREP(USBDRD_UCTL_CTL_REF_CLK_SEL, ref_clk_sel);
+
+	val &= ~USBDRD_UCTL_CTL_REF_CLK_FSEL;
+	val |= FIELD_PREP(USBDRD_UCTL_CTL_REF_CLK_FSEL, ref_clk_fsel);
+
+	val &= ~USBDRD_UCTL_CTL_MPLL_MULTIPLIER;
+	val |= FIELD_PREP(USBDRD_UCTL_CTL_MPLL_MULTIPLIER, mpll_mul);
+
+	/* Step 5b: Configure and enable spread-spectrum for SuperSpeed. */
+	val |= USBDRD_UCTL_CTL_SSC_EN;
+
+	/* Step 5c: Enable SuperSpeed. */
+	val |= USBDRD_UCTL_CTL_REF_SSP_EN;
+
+	/* Step 5d: Configure PHYs. SKIP */
+
+	/* Step 6a & 6b: Power up PHYs. */
+	val |= USBDRD_UCTL_CTL_HS_POWER_EN;
+	val |= USBDRD_UCTL_CTL_SS_POWER_EN;
+	dwc3_octeon_writeq(uctl_ctl_reg, val);
+
+	/* Step 7: Wait 10 controller-clock cycles to take effect. */
+	udelay(10);
+
+	/* Step 8a: Deassert UCTL reset signal. */
+	val = dwc3_octeon_readq(uctl_ctl_reg);
+	val &= ~USBDRD_UCTL_CTL_UCTL_RST;
+	dwc3_octeon_writeq(uctl_ctl_reg, val);
+
+	/* Step 8b: Wait 10 controller-clock cycles. */
+	udelay(10);
+
+	/* Step 8c: Setup power control. */
+	val = dwc3_octeon_readq(uctl_host_cfg_reg);
+	val |= USBDRD_UCTL_HOST_PPC_EN;
+	if (power_gpio == DWC3_GPIO_POWER_NONE) {
+		val &= ~USBDRD_UCTL_HOST_PPC_EN;
+	} else {
+		val |= USBDRD_UCTL_HOST_PPC_EN;
+		dwc3_octeon_config_gpio(((__force uintptr_t)octeon->base >> 24) & 1,
+					power_gpio);
+		dev_dbg(dev, "power control is using gpio%d\n", power_gpio);
+	}
+	if (power_active_low)
+		val &= ~USBDRD_UCTL_HOST_PPC_ACTIVE_HIGH_EN;
+	else
+		val |= USBDRD_UCTL_HOST_PPC_ACTIVE_HIGH_EN;
+	dwc3_octeon_writeq(uctl_host_cfg_reg, val);
+
+	/* Step 8d: Deassert UAHC reset signal. */
+	val = dwc3_octeon_readq(uctl_ctl_reg);
+	val &= ~USBDRD_UCTL_CTL_UAHC_RST;
+	dwc3_octeon_writeq(uctl_ctl_reg, val);
+
+	/* Step 8e: Wait 10 controller-clock cycles. */
+	udelay(10);
+
+	/* Step 9: Enable conditional coprocessor clock of UCTL. */
+	val = dwc3_octeon_readq(uctl_ctl_reg);
+	val |= USBDRD_UCTL_CTL_CSCLK_EN;
+	dwc3_octeon_writeq(uctl_ctl_reg, val);
+
+	/*Step 10: Set for host mode only. */
+	val = dwc3_octeon_readq(uctl_ctl_reg);
+	val &= ~USBDRD_UCTL_CTL_DRD_MODE;
+	dwc3_octeon_writeq(uctl_ctl_reg, val);
+
+	return 0;
+}
+
+static void dwc3_octeon_set_endian_mode(struct dwc3_octeon *octeon)
+{
+	u64 val;
+	void __iomem *uctl_shim_cfg_reg = octeon->base + USBDRD_UCTL_SHIM_CFG;
+
+	val = dwc3_octeon_readq(uctl_shim_cfg_reg);
+	val &= ~USBDRD_UCTL_SHIM_CFG_DMA_ENDIAN_MODE;
+	val &= ~USBDRD_UCTL_SHIM_CFG_CSR_ENDIAN_MODE;
+#ifdef __BIG_ENDIAN
+	val |= FIELD_PREP(USBDRD_UCTL_SHIM_CFG_DMA_ENDIAN_MODE, 1);
+	val |= FIELD_PREP(USBDRD_UCTL_SHIM_CFG_CSR_ENDIAN_MODE, 1);
+#endif
+	dwc3_octeon_writeq(uctl_shim_cfg_reg, val);
+}
+
+static void dwc3_octeon_phy_reset(struct dwc3_octeon *octeon)
+{
+	u64 val;
+	void __iomem *uctl_ctl_reg = octeon->base + USBDRD_UCTL_CTL;
+
+	val = dwc3_octeon_readq(uctl_ctl_reg);
+	val &= ~USBDRD_UCTL_CTL_UPHY_RST;
+	dwc3_octeon_writeq(uctl_ctl_reg, val);
+}
+
+static int dwc3_octeon_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
+	struct dwc3_octeon *octeon;
+	const char *hs_clock_type, *ss_clock_type;
+	int ref_clk_sel, ref_clk_fsel, mpll_mul;
+	int power_active_low, power_gpio;
+	int err, len;
+	u32 clock_rate;
+
+	if (of_property_read_u32(node, "refclk-frequency", &clock_rate)) {
+		dev_err(dev, "No UCTL \"refclk-frequency\"\n");
+		return -EINVAL;
+	}
+	if (of_property_read_string(node, "refclk-type-ss", &ss_clock_type)) {
+		dev_err(dev, "No UCTL \"refclk-type-ss\"\n");
+		return -EINVAL;
+	}
+	if (of_property_read_string(node, "refclk-type-hs", &hs_clock_type)) {
+		dev_err(dev, "No UCTL \"refclk-type-hs\"\n");
+		return -EINVAL;
+	}
+
+	ref_clk_sel = 2;
+	if (strcmp("dlmc_ref_clk0", ss_clock_type) == 0) {
+		if (strcmp(hs_clock_type, "dlmc_ref_clk0") == 0)
+			ref_clk_sel = 0;
+		else if (strcmp(hs_clock_type, "pll_ref_clk"))
+			dev_warn(dev, "Invalid HS clock type %s, using pll_ref_clk instead\n",
+				 hs_clock_type);
+	} else if (strcmp(ss_clock_type, "dlmc_ref_clk1") == 0) {
+		if (strcmp(hs_clock_type, "dlmc_ref_clk1") == 0) {
+			ref_clk_sel = 1;
+		} else {
+			ref_clk_sel = 3;
+			if (strcmp(hs_clock_type, "pll_ref_clk"))
+				dev_warn(dev, "Invalid HS clock type %s, using pll_ref_clk instead\n",
+					 hs_clock_type);
+		}
+	} else {
+		dev_warn(dev, "Invalid SS clock type %s, using dlmc_ref_clk0 instead\n",
+			 ss_clock_type);
+	}
+
+	ref_clk_fsel = 0x07;
+	switch (clock_rate) {
+	default:
+		dev_warn(dev, "Invalid ref_clk %u, using 100000000 instead\n",
+			 clock_rate);
+		fallthrough;
+	case 100000000:
+		mpll_mul = 0x19;
+		if (ref_clk_sel < 2)
+			ref_clk_fsel = 0x27;
+		break;
+	case 50000000:
+		mpll_mul = 0x32;
+		break;
+	case 125000000:
+		mpll_mul = 0x28;
+		break;
+	}
+
+	power_gpio = DWC3_GPIO_POWER_NONE;
+	power_active_low = 0;
+	if (of_find_property(node, "power", &len)) {
+		u32 gpio_pwr[3];
+
+		switch (len) {
+		case 8:
+			of_property_read_u32_array(node, "power", gpio_pwr, 2);
+			break;
+		case 12:
+			of_property_read_u32_array(node, "power", gpio_pwr, 3);
+			power_active_low = gpio_pwr[2] & 0x01;
+			break;
+		default:
+			dev_err(dev, "invalid power configuration\n");
+			return -EINVAL;
+		}
+		power_gpio = gpio_pwr[1];
+	}
+
+	octeon = devm_kzalloc(dev, sizeof(*octeon), GFP_KERNEL);
+	if (!octeon)
+		return -ENOMEM;
+
+	octeon->dev = dev;
+	octeon->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(octeon->base))
+		return PTR_ERR(octeon->base);
+
+	err = dwc3_octeon_setup(octeon, ref_clk_sel, ref_clk_fsel, mpll_mul,
+				power_gpio, power_active_low);
+	if (err)
+		return err;
+
+	dwc3_octeon_set_endian_mode(octeon);
+	dwc3_octeon_phy_reset(octeon);
+
+	platform_set_drvdata(pdev, octeon);
+
+	return of_platform_populate(node, NULL, NULL, dev);
+}
+
+static void dwc3_octeon_remove(struct platform_device *pdev)
+{
+	struct dwc3_octeon *octeon = platform_get_drvdata(pdev);
+
+	of_platform_depopulate(octeon->dev);
+}
+
+static const struct of_device_id dwc3_octeon_of_match[] = {
+	{ .compatible = "cavium,octeon-7130-usb-uctl" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, dwc3_octeon_of_match);
+
+static struct platform_driver dwc3_octeon_driver = {
+	.probe		= dwc3_octeon_probe,
+	.remove_new	= dwc3_octeon_remove,
+	.driver		= {
+		.name	= "dwc3-octeon",
+		.of_match_table = dwc3_octeon_of_match,
+	},
+};
+module_platform_driver(dwc3_octeon_driver);
+
+MODULE_ALIAS("platform:dwc3-octeon");
+MODULE_AUTHOR("Ladislav Michl <ladis@linux-mips.org>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("DesignWare USB3 OCTEON III Glue Layer");