Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 866 insertions, 0 deletions

diff --git a/drivers/usb/serial/ch341.c b/drivers/usb/serial/ch341.c
new file mode 100644
index 0000000000..612bea504d
--- /dev/null
+++ b/drivers/usb/serial/ch341.c
@@ -0,0 +1,866 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2007, Frank A Kingswood <frank@kingswood-consulting.co.uk>
+ * Copyright 2007, Werner Cornelius <werner@cornelius-consult.de>
+ * Copyright 2009, Boris Hajduk <boris@hajduk.org>
+ *
+ * ch341.c implements a serial port driver for the Winchiphead CH341.
+ *
+ * The CH341 device can be used to implement an RS232 asynchronous
+ * serial port, an IEEE-1284 parallel printer port or a memory-like
+ * interface. In all cases the CH341 supports an I2C interface as well.
+ * This driver only supports the asynchronous serial interface.
+ */
+
+#include <linux/kernel.h>
+#include <linux/tty.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/usb.h>
+#include <linux/usb/serial.h>
+#include <linux/serial.h>
+#include <asm/unaligned.h>
+
+#define DEFAULT_BAUD_RATE 9600
+#define DEFAULT_TIMEOUT   1000
+
+/* flags for IO-Bits */
+#define CH341_BIT_RTS (1 << 6)
+#define CH341_BIT_DTR (1 << 5)
+
+/******************************/
+/* interrupt pipe definitions */
+/******************************/
+/* always 4 interrupt bytes */
+/* first irq byte normally 0x08 */
+/* second irq byte base 0x7d + below */
+/* third irq byte base 0x94 + below */
+/* fourth irq byte normally 0xee */
+
+/* second interrupt byte */
+#define CH341_MULT_STAT 0x04 /* multiple status since last interrupt event */
+
+/* status returned in third interrupt answer byte, inverted in data
+   from irq */
+#define CH341_BIT_CTS 0x01
+#define CH341_BIT_DSR 0x02
+#define CH341_BIT_RI  0x04
+#define CH341_BIT_DCD 0x08
+#define CH341_BITS_MODEM_STAT 0x0f /* all bits */
+
+/* Break support - the information used to implement this was gleaned from
+ * the Net/FreeBSD uchcom.c driver by Takanori Watanabe.  Domo arigato.
+ */
+
+#define CH341_REQ_READ_VERSION 0x5F
+#define CH341_REQ_WRITE_REG    0x9A
+#define CH341_REQ_READ_REG     0x95
+#define CH341_REQ_SERIAL_INIT  0xA1
+#define CH341_REQ_MODEM_CTRL   0xA4
+
+#define CH341_REG_BREAK        0x05
+#define CH341_REG_PRESCALER    0x12
+#define CH341_REG_DIVISOR      0x13
+#define CH341_REG_LCR          0x18
+#define CH341_REG_LCR2         0x25
+
+#define CH341_NBREAK_BITS      0x01
+
+#define CH341_LCR_ENABLE_RX    0x80
+#define CH341_LCR_ENABLE_TX    0x40
+#define CH341_LCR_MARK_SPACE   0x20
+#define CH341_LCR_PAR_EVEN     0x10
+#define CH341_LCR_ENABLE_PAR   0x08
+#define CH341_LCR_STOP_BITS_2  0x04
+#define CH341_LCR_CS8          0x03
+#define CH341_LCR_CS7          0x02
+#define CH341_LCR_CS6          0x01
+#define CH341_LCR_CS5          0x00
+
+#define CH341_QUIRK_LIMITED_PRESCALER	BIT(0)
+#define CH341_QUIRK_SIMULATE_BREAK	BIT(1)
+
+static const struct usb_device_id id_table[] = {
+	{ USB_DEVICE(0x1a86, 0x5523) },
+	{ USB_DEVICE(0x1a86, 0x7522) },
+	{ USB_DEVICE(0x1a86, 0x7523) },
+	{ USB_DEVICE(0x2184, 0x0057) },
+	{ USB_DEVICE(0x4348, 0x5523) },
+	{ USB_DEVICE(0x9986, 0x7523) },
+	{ },
+};
+MODULE_DEVICE_TABLE(usb, id_table);
+
+struct ch341_private {
+	spinlock_t lock; /* access lock */
+	unsigned baud_rate; /* set baud rate */
+	u8 mcr;
+	u8 msr;
+	u8 lcr;
+
+	unsigned long quirks;
+	u8 version;
+
+	unsigned long break_end;
+};
+
+static void ch341_set_termios(struct tty_struct *tty,
+			      struct usb_serial_port *port,
+			      const struct ktermios *old_termios);
+
+static int ch341_control_out(struct usb_device *dev, u8 request,
+			     u16 value, u16 index)
+{
+	int r;
+
+	dev_dbg(&dev->dev, "%s - (%02x,%04x,%04x)\n", __func__,
+		request, value, index);
+
+	r = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), request,
+			    USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
+			    value, index, NULL, 0, DEFAULT_TIMEOUT);
+	if (r < 0)
+		dev_err(&dev->dev, "failed to send control message: %d\n", r);
+
+	return r;
+}
+
+static int ch341_control_in(struct usb_device *dev,
+			    u8 request, u16 value, u16 index,
+			    char *buf, unsigned bufsize)
+{
+	int r;
+
+	dev_dbg(&dev->dev, "%s - (%02x,%04x,%04x,%u)\n", __func__,
+		request, value, index, bufsize);
+
+	r = usb_control_msg_recv(dev, 0, request,
+				 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
+				 value, index, buf, bufsize, DEFAULT_TIMEOUT,
+				 GFP_KERNEL);
+	if (r) {
+		dev_err(&dev->dev, "failed to receive control message: %d\n",
+			r);
+		return r;
+	}
+
+	return 0;
+}
+
+#define CH341_CLKRATE		48000000
+#define CH341_CLK_DIV(ps, fact)	(1 << (12 - 3 * (ps) - (fact)))
+#define CH341_MIN_RATE(ps)	(CH341_CLKRATE / (CH341_CLK_DIV((ps), 1) * 512))
+
+static const speed_t ch341_min_rates[] = {
+	CH341_MIN_RATE(0),
+	CH341_MIN_RATE(1),
+	CH341_MIN_RATE(2),
+	CH341_MIN_RATE(3),
+};
+
+/* Supported range is 46 to 3000000 bps. */
+#define CH341_MIN_BPS	DIV_ROUND_UP(CH341_CLKRATE, CH341_CLK_DIV(0, 0) * 256)
+#define CH341_MAX_BPS	(CH341_CLKRATE / (CH341_CLK_DIV(3, 0) * 2))
+
+/*
+ * The device line speed is given by the following equation:
+ *
+ *	baudrate = 48000000 / (2^(12 - 3 * ps - fact) * div), where
+ *
+ *		0 <= ps <= 3,
+ *		0 <= fact <= 1,
+ *		2 <= div <= 256 if fact = 0, or
+ *		9 <= div <= 256 if fact = 1
+ */
+static int ch341_get_divisor(struct ch341_private *priv, speed_t speed)
+{
+	unsigned int fact, div, clk_div;
+	bool force_fact0 = false;
+	int ps;
+
+	/*
+	 * Clamp to supported range, this makes the (ps < 0) and (div < 2)
+	 * sanity checks below redundant.
+	 */
+	speed = clamp_val(speed, CH341_MIN_BPS, CH341_MAX_BPS);
+
+	/*
+	 * Start with highest possible base clock (fact = 1) that will give a
+	 * divisor strictly less than 512.
+	 */
+	fact = 1;
+	for (ps = 3; ps >= 0; ps--) {
+		if (speed > ch341_min_rates[ps])
+			break;
+	}
+
+	if (ps < 0)
+		return -EINVAL;
+
+	/* Determine corresponding divisor, rounding down. */
+	clk_div = CH341_CLK_DIV(ps, fact);
+	div = CH341_CLKRATE / (clk_div * speed);
+
+	/* Some devices require a lower base clock if ps < 3. */
+	if (ps < 3 && (priv->quirks & CH341_QUIRK_LIMITED_PRESCALER))
+		force_fact0 = true;
+
+	/* Halve base clock (fact = 0) if required. */
+	if (div < 9 || div > 255 || force_fact0) {
+		div /= 2;
+		clk_div *= 2;
+		fact = 0;
+	}
+
+	if (div < 2)
+		return -EINVAL;
+
+	/*
+	 * Pick next divisor if resulting rate is closer to the requested one,
+	 * scale up to avoid rounding errors on low rates.
+	 */
+	if (16 * CH341_CLKRATE / (clk_div * div) - 16 * speed >=
+			16 * speed - 16 * CH341_CLKRATE / (clk_div * (div + 1)))
+		div++;
+
+	/*
+	 * Prefer lower base clock (fact = 0) if even divisor.
+	 *
+	 * Note that this makes the receiver more tolerant to errors.
+	 */
+	if (fact == 1 && div % 2 == 0) {
+		div /= 2;
+		fact = 0;
+	}
+
+	return (0x100 - div) << 8 | fact << 2 | ps;
+}
+
+static int ch341_set_baudrate_lcr(struct usb_device *dev,
+				  struct ch341_private *priv,
+				  speed_t baud_rate, u8 lcr)
+{
+	int val;
+	int r;
+
+	if (!baud_rate)
+		return -EINVAL;
+
+	val = ch341_get_divisor(priv, baud_rate);
+	if (val < 0)
+		return -EINVAL;
+
+	/*
+	 * CH341A buffers data until a full endpoint-size packet (32 bytes)
+	 * has been received unless bit 7 is set.
+	 *
+	 * At least one device with version 0x27 appears to have this bit
+	 * inverted.
+	 */
+	if (priv->version > 0x27)
+		val |= BIT(7);
+
+	r = ch341_control_out(dev, CH341_REQ_WRITE_REG,
+			      CH341_REG_DIVISOR << 8 | CH341_REG_PRESCALER,
+			      val);
+	if (r)
+		return r;
+
+	/*
+	 * Chip versions before version 0x30 as read using
+	 * CH341_REQ_READ_VERSION used separate registers for line control
+	 * (stop bits, parity and word length). Version 0x30 and above use
+	 * CH341_REG_LCR only and CH341_REG_LCR2 is always set to zero.
+	 */
+	if (priv->version < 0x30)
+		return 0;
+
+	r = ch341_control_out(dev, CH341_REQ_WRITE_REG,
+			      CH341_REG_LCR2 << 8 | CH341_REG_LCR, lcr);
+	if (r)
+		return r;
+
+	return r;
+}
+
+static int ch341_set_handshake(struct usb_device *dev, u8 control)
+{
+	return ch341_control_out(dev, CH341_REQ_MODEM_CTRL, ~control, 0);
+}
+
+static int ch341_get_status(struct usb_device *dev, struct ch341_private *priv)
+{
+	const unsigned int size = 2;
+	u8 buffer[2];
+	int r;
+	unsigned long flags;
+
+	r = ch341_control_in(dev, CH341_REQ_READ_REG, 0x0706, 0, buffer, size);
+	if (r)
+		return r;
+
+	spin_lock_irqsave(&priv->lock, flags);
+	priv->msr = (~(*buffer)) & CH341_BITS_MODEM_STAT;
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	return 0;
+}
+
+/* -------------------------------------------------------------------------- */
+
+static int ch341_configure(struct usb_device *dev, struct ch341_private *priv)
+{
+	const unsigned int size = 2;
+	u8 buffer[2];
+	int r;
+
+	/* expect two bytes 0x27 0x00 */
+	r = ch341_control_in(dev, CH341_REQ_READ_VERSION, 0, 0, buffer, size);
+	if (r)
+		return r;
+
+	priv->version = buffer[0];
+	dev_dbg(&dev->dev, "Chip version: 0x%02x\n", priv->version);
+
+	r = ch341_control_out(dev, CH341_REQ_SERIAL_INIT, 0, 0);
+	if (r < 0)
+		return r;
+
+	r = ch341_set_baudrate_lcr(dev, priv, priv->baud_rate, priv->lcr);
+	if (r < 0)
+		return r;
+
+	r = ch341_set_handshake(dev, priv->mcr);
+	if (r < 0)
+		return r;
+
+	return 0;
+}
+
+static int ch341_detect_quirks(struct usb_serial_port *port)
+{
+	struct ch341_private *priv = usb_get_serial_port_data(port);
+	struct usb_device *udev = port->serial->dev;
+	const unsigned int size = 2;
+	unsigned long quirks = 0;
+	u8 buffer[2];
+	int r;
+
+	/*
+	 * A subset of CH34x devices does not support all features. The
+	 * prescaler is limited and there is no support for sending a RS232
+	 * break condition. A read failure when trying to set up the latter is
+	 * used to detect these devices.
+	 */
+	r = usb_control_msg_recv(udev, 0, CH341_REQ_READ_REG,
+				 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
+				 CH341_REG_BREAK, 0, &buffer, size,
+				 DEFAULT_TIMEOUT, GFP_KERNEL);
+	if (r == -EPIPE) {
+		dev_info(&port->dev, "break control not supported, using simulated break\n");
+		quirks = CH341_QUIRK_LIMITED_PRESCALER | CH341_QUIRK_SIMULATE_BREAK;
+		r = 0;
+	} else if (r) {
+		dev_err(&port->dev, "failed to read break control: %d\n", r);
+	}
+
+	if (quirks) {
+		dev_dbg(&port->dev, "enabling quirk flags: 0x%02lx\n", quirks);
+		priv->quirks |= quirks;
+	}
+
+	return r;
+}
+
+static int ch341_port_probe(struct usb_serial_port *port)
+{
+	struct ch341_private *priv;
+	int r;
+
+	priv = kzalloc(sizeof(struct ch341_private), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	spin_lock_init(&priv->lock);
+	priv->baud_rate = DEFAULT_BAUD_RATE;
+	/*
+	 * Some CH340 devices appear unable to change the initial LCR
+	 * settings, so set a sane 8N1 default.
+	 */
+	priv->lcr = CH341_LCR_ENABLE_RX | CH341_LCR_ENABLE_TX | CH341_LCR_CS8;
+
+	r = ch341_configure(port->serial->dev, priv);
+	if (r < 0)
+		goto error;
+
+	usb_set_serial_port_data(port, priv);
+
+	r = ch341_detect_quirks(port);
+	if (r < 0)
+		goto error;
+
+	return 0;
+
+error:	kfree(priv);
+	return r;
+}
+
+static void ch341_port_remove(struct usb_serial_port *port)
+{
+	struct ch341_private *priv;
+
+	priv = usb_get_serial_port_data(port);
+	kfree(priv);
+}
+
+static int ch341_carrier_raised(struct usb_serial_port *port)
+{
+	struct ch341_private *priv = usb_get_serial_port_data(port);
+	if (priv->msr & CH341_BIT_DCD)
+		return 1;
+	return 0;
+}
+
+static void ch341_dtr_rts(struct usb_serial_port *port, int on)
+{
+	struct ch341_private *priv = usb_get_serial_port_data(port);
+	unsigned long flags;
+
+	/* drop DTR and RTS */
+	spin_lock_irqsave(&priv->lock, flags);
+	if (on)
+		priv->mcr |= CH341_BIT_RTS | CH341_BIT_DTR;
+	else
+		priv->mcr &= ~(CH341_BIT_RTS | CH341_BIT_DTR);
+	spin_unlock_irqrestore(&priv->lock, flags);
+	ch341_set_handshake(port->serial->dev, priv->mcr);
+}
+
+static void ch341_close(struct usb_serial_port *port)
+{
+	usb_serial_generic_close(port);
+	usb_kill_urb(port->interrupt_in_urb);
+}
+
+
+/* open this device, set default parameters */
+static int ch341_open(struct tty_struct *tty, struct usb_serial_port *port)
+{
+	struct ch341_private *priv = usb_get_serial_port_data(port);
+	int r;
+
+	if (tty)
+		ch341_set_termios(tty, port, NULL);
+
+	dev_dbg(&port->dev, "%s - submitting interrupt urb\n", __func__);
+	r = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL);
+	if (r) {
+		dev_err(&port->dev, "%s - failed to submit interrupt urb: %d\n",
+			__func__, r);
+		return r;
+	}
+
+	r = ch341_get_status(port->serial->dev, priv);
+	if (r < 0) {
+		dev_err(&port->dev, "failed to read modem status: %d\n", r);
+		goto err_kill_interrupt_urb;
+	}
+
+	r = usb_serial_generic_open(tty, port);
+	if (r)
+		goto err_kill_interrupt_urb;
+
+	return 0;
+
+err_kill_interrupt_urb:
+	usb_kill_urb(port->interrupt_in_urb);
+
+	return r;
+}
+
+/* Old_termios contains the original termios settings and
+ * tty->termios contains the new setting to be used.
+ */
+static void ch341_set_termios(struct tty_struct *tty,
+			      struct usb_serial_port *port,
+			      const struct ktermios *old_termios)
+{
+	struct ch341_private *priv = usb_get_serial_port_data(port);
+	unsigned baud_rate;
+	unsigned long flags;
+	u8 lcr;
+	int r;
+
+	/* redundant changes may cause the chip to lose bytes */
+	if (old_termios && !tty_termios_hw_change(&tty->termios, old_termios))
+		return;
+
+	baud_rate = tty_get_baud_rate(tty);
+
+	lcr = CH341_LCR_ENABLE_RX | CH341_LCR_ENABLE_TX;
+
+	switch (C_CSIZE(tty)) {
+	case CS5:
+		lcr |= CH341_LCR_CS5;
+		break;
+	case CS6:
+		lcr |= CH341_LCR_CS6;
+		break;
+	case CS7:
+		lcr |= CH341_LCR_CS7;
+		break;
+	case CS8:
+		lcr |= CH341_LCR_CS8;
+		break;
+	}
+
+	if (C_PARENB(tty)) {
+		lcr |= CH341_LCR_ENABLE_PAR;
+		if (C_PARODD(tty) == 0)
+			lcr |= CH341_LCR_PAR_EVEN;
+		if (C_CMSPAR(tty))
+			lcr |= CH341_LCR_MARK_SPACE;
+	}
+
+	if (C_CSTOPB(tty))
+		lcr |= CH341_LCR_STOP_BITS_2;
+
+	if (baud_rate) {
+		priv->baud_rate = baud_rate;
+
+		r = ch341_set_baudrate_lcr(port->serial->dev, priv,
+					   priv->baud_rate, lcr);
+		if (r < 0 && old_termios) {
+			priv->baud_rate = tty_termios_baud_rate(old_termios);
+			tty_termios_copy_hw(&tty->termios, old_termios);
+		} else if (r == 0) {
+			priv->lcr = lcr;
+		}
+	}
+
+	spin_lock_irqsave(&priv->lock, flags);
+	if (C_BAUD(tty) == B0)
+		priv->mcr &= ~(CH341_BIT_DTR | CH341_BIT_RTS);
+	else if (old_termios && (old_termios->c_cflag & CBAUD) == B0)
+		priv->mcr |= (CH341_BIT_DTR | CH341_BIT_RTS);
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	ch341_set_handshake(port->serial->dev, priv->mcr);
+}
+
+/*
+ * A subset of all CH34x devices don't support a real break condition and
+ * reading CH341_REG_BREAK fails (see also ch341_detect_quirks). This function
+ * simulates a break condition by lowering the baud rate to the minimum
+ * supported by the hardware upon enabling the break condition and sending
+ * a NUL byte.
+ *
+ * Incoming data is corrupted while the break condition is being simulated.
+ *
+ * Normally the duration of the break condition can be controlled individually
+ * by userspace using TIOCSBRK and TIOCCBRK or by passing an argument to
+ * TCSBRKP. Due to how the simulation is implemented the duration can't be
+ * controlled. The duration is always about (1s / 46bd * 9bit) = 196ms.
+ */
+static int ch341_simulate_break(struct tty_struct *tty, int break_state)
+{
+	struct usb_serial_port *port = tty->driver_data;
+	struct ch341_private *priv = usb_get_serial_port_data(port);
+	unsigned long now, delay;
+	int r, r2;
+
+	if (break_state != 0) {
+		dev_dbg(&port->dev, "enter break state requested\n");
+
+		r = ch341_set_baudrate_lcr(port->serial->dev, priv,
+				CH341_MIN_BPS,
+				CH341_LCR_ENABLE_RX | CH341_LCR_ENABLE_TX | CH341_LCR_CS8);
+		if (r < 0) {
+			dev_err(&port->dev,
+				"failed to change baud rate to %u: %d\n",
+				CH341_MIN_BPS, r);
+			goto restore;
+		}
+
+		r = tty_put_char(tty, '\0');
+		if (r < 0) {
+			dev_err(&port->dev,
+				"failed to write NUL byte for simulated break condition: %d\n",
+				r);
+			goto restore;
+		}
+
+		/*
+		 * Compute expected transmission duration including safety
+		 * margin. The original baud rate is only restored after the
+		 * computed point in time.
+		 *
+		 * 11 bits = 1 start, 8 data, 1 stop, 1 margin
+		 */
+		priv->break_end = jiffies + (11 * HZ / CH341_MIN_BPS);
+
+		return 0;
+	}
+
+	dev_dbg(&port->dev, "leave break state requested\n");
+
+	now = jiffies;
+
+	if (time_before(now, priv->break_end)) {
+		/* Wait until NUL byte is written */
+		delay = priv->break_end - now;
+		dev_dbg(&port->dev,
+			"wait %d ms while transmitting NUL byte at %u baud\n",
+			jiffies_to_msecs(delay), CH341_MIN_BPS);
+		schedule_timeout_interruptible(delay);
+	}
+
+	r = 0;
+restore:
+	/* Restore original baud rate */
+	r2 = ch341_set_baudrate_lcr(port->serial->dev, priv, priv->baud_rate,
+			priv->lcr);
+	if (r2 < 0) {
+		dev_err(&port->dev,
+			"restoring original baud rate of %u failed: %d\n",
+			priv->baud_rate, r2);
+		return r2;
+	}
+
+	return r;
+}
+
+static int ch341_break_ctl(struct tty_struct *tty, int break_state)
+{
+	const uint16_t ch341_break_reg =
+			((uint16_t) CH341_REG_LCR << 8) | CH341_REG_BREAK;
+	struct usb_serial_port *port = tty->driver_data;
+	struct ch341_private *priv = usb_get_serial_port_data(port);
+	int r;
+	uint16_t reg_contents;
+	uint8_t break_reg[2];
+
+	if (priv->quirks & CH341_QUIRK_SIMULATE_BREAK)
+		return ch341_simulate_break(tty, break_state);
+
+	r = ch341_control_in(port->serial->dev, CH341_REQ_READ_REG,
+			ch341_break_reg, 0, break_reg, 2);
+	if (r) {
+		dev_err(&port->dev, "%s - USB control read error (%d)\n",
+				__func__, r);
+		if (r > 0)
+			r = -EIO;
+		return r;
+	}
+	dev_dbg(&port->dev, "%s - initial ch341 break register contents - reg1: %x, reg2: %x\n",
+		__func__, break_reg[0], break_reg[1]);
+	if (break_state != 0) {
+		dev_dbg(&port->dev, "%s - Enter break state requested\n", __func__);
+		break_reg[0] &= ~CH341_NBREAK_BITS;
+		break_reg[1] &= ~CH341_LCR_ENABLE_TX;
+	} else {
+		dev_dbg(&port->dev, "%s - Leave break state requested\n", __func__);
+		break_reg[0] |= CH341_NBREAK_BITS;
+		break_reg[1] |= CH341_LCR_ENABLE_TX;
+	}
+	dev_dbg(&port->dev, "%s - New ch341 break register contents - reg1: %x, reg2: %x\n",
+		__func__, break_reg[0], break_reg[1]);
+	reg_contents = get_unaligned_le16(break_reg);
+	r = ch341_control_out(port->serial->dev, CH341_REQ_WRITE_REG,
+			ch341_break_reg, reg_contents);
+	if (r < 0) {
+		dev_err(&port->dev, "%s - USB control write error (%d)\n",
+				__func__, r);
+		return r;
+	}
+
+	return 0;
+}
+
+static int ch341_tiocmset(struct tty_struct *tty,
+			  unsigned int set, unsigned int clear)
+{
+	struct usb_serial_port *port = tty->driver_data;
+	struct ch341_private *priv = usb_get_serial_port_data(port);
+	unsigned long flags;
+	u8 control;
+
+	spin_lock_irqsave(&priv->lock, flags);
+	if (set & TIOCM_RTS)
+		priv->mcr |= CH341_BIT_RTS;
+	if (set & TIOCM_DTR)
+		priv->mcr |= CH341_BIT_DTR;
+	if (clear & TIOCM_RTS)
+		priv->mcr &= ~CH341_BIT_RTS;
+	if (clear & TIOCM_DTR)
+		priv->mcr &= ~CH341_BIT_DTR;
+	control = priv->mcr;
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	return ch341_set_handshake(port->serial->dev, control);
+}
+
+static void ch341_update_status(struct usb_serial_port *port,
+					unsigned char *data, size_t len)
+{
+	struct ch341_private *priv = usb_get_serial_port_data(port);
+	struct tty_struct *tty;
+	unsigned long flags;
+	u8 status;
+	u8 delta;
+
+	if (len < 4)
+		return;
+
+	status = ~data[2] & CH341_BITS_MODEM_STAT;
+
+	spin_lock_irqsave(&priv->lock, flags);
+	delta = status ^ priv->msr;
+	priv->msr = status;
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	if (data[1] & CH341_MULT_STAT)
+		dev_dbg(&port->dev, "%s - multiple status change\n", __func__);
+
+	if (!delta)
+		return;
+
+	if (delta & CH341_BIT_CTS)
+		port->icount.cts++;
+	if (delta & CH341_BIT_DSR)
+		port->icount.dsr++;
+	if (delta & CH341_BIT_RI)
+		port->icount.rng++;
+	if (delta & CH341_BIT_DCD) {
+		port->icount.dcd++;
+		tty = tty_port_tty_get(&port->port);
+		if (tty) {
+			usb_serial_handle_dcd_change(port, tty,
+						status & CH341_BIT_DCD);
+			tty_kref_put(tty);
+		}
+	}
+
+	wake_up_interruptible(&port->port.delta_msr_wait);
+}
+
+static void ch341_read_int_callback(struct urb *urb)
+{
+	struct usb_serial_port *port = urb->context;
+	unsigned char *data = urb->transfer_buffer;
+	unsigned int len = urb->actual_length;
+	int status;
+
+	switch (urb->status) {
+	case 0:
+		/* success */
+		break;
+	case -ECONNRESET:
+	case -ENOENT:
+	case -ESHUTDOWN:
+		/* this urb is terminated, clean up */
+		dev_dbg(&urb->dev->dev, "%s - urb shutting down: %d\n",
+			__func__, urb->status);
+		return;
+	default:
+		dev_dbg(&urb->dev->dev, "%s - nonzero urb status: %d\n",
+			__func__, urb->status);
+		goto exit;
+	}
+
+	usb_serial_debug_data(&port->dev, __func__, len, data);
+	ch341_update_status(port, data, len);
+exit:
+	status = usb_submit_urb(urb, GFP_ATOMIC);
+	if (status) {
+		dev_err(&urb->dev->dev, "%s - usb_submit_urb failed: %d\n",
+			__func__, status);
+	}
+}
+
+static int ch341_tiocmget(struct tty_struct *tty)
+{
+	struct usb_serial_port *port = tty->driver_data;
+	struct ch341_private *priv = usb_get_serial_port_data(port);
+	unsigned long flags;
+	u8 mcr;
+	u8 status;
+	unsigned int result;
+
+	spin_lock_irqsave(&priv->lock, flags);
+	mcr = priv->mcr;
+	status = priv->msr;
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	result = ((mcr & CH341_BIT_DTR)		? TIOCM_DTR : 0)
+		  | ((mcr & CH341_BIT_RTS)	? TIOCM_RTS : 0)
+		  | ((status & CH341_BIT_CTS)	? TIOCM_CTS : 0)
+		  | ((status & CH341_BIT_DSR)	? TIOCM_DSR : 0)
+		  | ((status & CH341_BIT_RI)	? TIOCM_RI  : 0)
+		  | ((status & CH341_BIT_DCD)	? TIOCM_CD  : 0);
+
+	dev_dbg(&port->dev, "%s - result = %x\n", __func__, result);
+
+	return result;
+}
+
+static int ch341_reset_resume(struct usb_serial *serial)
+{
+	struct usb_serial_port *port = serial->port[0];
+	struct ch341_private *priv;
+	int ret;
+
+	priv = usb_get_serial_port_data(port);
+	if (!priv)
+		return 0;
+
+	/* reconfigure ch341 serial port after bus-reset */
+	ch341_configure(serial->dev, priv);
+
+	if (tty_port_initialized(&port->port)) {
+		ret = usb_submit_urb(port->interrupt_in_urb, GFP_NOIO);
+		if (ret) {
+			dev_err(&port->dev, "failed to submit interrupt urb: %d\n",
+				ret);
+			return ret;
+		}
+
+		ret = ch341_get_status(port->serial->dev, priv);
+		if (ret < 0) {
+			dev_err(&port->dev, "failed to read modem status: %d\n",
+				ret);
+		}
+	}
+
+	return usb_serial_generic_resume(serial);
+}
+
+static struct usb_serial_driver ch341_device = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= "ch341-uart",
+	},
+	.id_table          = id_table,
+	.num_ports         = 1,
+	.open              = ch341_open,
+	.dtr_rts	   = ch341_dtr_rts,
+	.carrier_raised	   = ch341_carrier_raised,
+	.close             = ch341_close,
+	.set_termios       = ch341_set_termios,
+	.break_ctl         = ch341_break_ctl,
+	.tiocmget          = ch341_tiocmget,
+	.tiocmset          = ch341_tiocmset,
+	.tiocmiwait        = usb_serial_generic_tiocmiwait,
+	.read_int_callback = ch341_read_int_callback,
+	.port_probe        = ch341_port_probe,
+	.port_remove       = ch341_port_remove,
+	.reset_resume      = ch341_reset_resume,
+};
+
+static struct usb_serial_driver * const serial_drivers[] = {
+	&ch341_device, NULL
+};
+
+module_usb_serial_driver(serial_drivers, id_table);
+
+MODULE_LICENSE("GPL v2");