Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 1745 insertions, 0 deletions

diff --git a/sound/soc/fsl/fsl_ssi.c b/sound/soc/fsl/fsl_ssi.c
new file mode 100644
index 0000000000..079ac04272
--- /dev/null
+++ b/sound/soc/fsl/fsl_ssi.c
@@ -0,0 +1,1745 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Freescale SSI ALSA SoC Digital Audio Interface (DAI) driver
+//
+// Author: Timur Tabi <timur@freescale.com>
+//
+// Copyright 2007-2010 Freescale Semiconductor, Inc.
+//
+// Some notes why imx-pcm-fiq is used instead of DMA on some boards:
+//
+// The i.MX SSI core has some nasty limitations in AC97 mode. While most
+// sane processor vendors have a FIFO per AC97 slot, the i.MX has only
+// one FIFO which combines all valid receive slots. We cannot even select
+// which slots we want to receive. The WM9712 with which this driver
+// was developed with always sends GPIO status data in slot 12 which
+// we receive in our (PCM-) data stream. The only chance we have is to
+// manually skip this data in the FIQ handler. With sampling rates different
+// from 48000Hz not every frame has valid receive data, so the ratio
+// between pcm data and GPIO status data changes. Our FIQ handler is not
+// able to handle this, hence this driver only works with 48000Hz sampling
+// rate.
+// Reading and writing AC97 registers is another challenge. The core
+// provides us status bits when the read register is updated with *another*
+// value. When we read the same register two times (and the register still
+// contains the same value) these status bits are not set. We work
+// around this by not polling these bits but only wait a fixed delay.
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/clk.h>
+#include <linux/ctype.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/dma/imx-dma.h>
+
+#include <sound/core.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/initval.h>
+#include <sound/soc.h>
+#include <sound/dmaengine_pcm.h>
+
+#include "fsl_ssi.h"
+#include "imx-pcm.h"
+
+/* Define RX and TX to index ssi->regvals array; Can be 0 or 1 only */
+#define RX 0
+#define TX 1
+
+/**
+ * FSLSSI_I2S_FORMATS: audio formats supported by the SSI
+ *
+ * The SSI has a limitation in that the samples must be in the same byte
+ * order as the host CPU.  This is because when multiple bytes are written
+ * to the STX register, the bytes and bits must be written in the same
+ * order.  The STX is a shift register, so all the bits need to be aligned
+ * (bit-endianness must match byte-endianness).  Processors typically write
+ * the bits within a byte in the same order that the bytes of a word are
+ * written in.  So if the host CPU is big-endian, then only big-endian
+ * samples will be written to STX properly.
+ */
+#ifdef __BIG_ENDIAN
+#define FSLSSI_I2S_FORMATS \
+	(SNDRV_PCM_FMTBIT_S8 | \
+	 SNDRV_PCM_FMTBIT_S16_BE | \
+	 SNDRV_PCM_FMTBIT_S18_3BE | \
+	 SNDRV_PCM_FMTBIT_S20_3BE | \
+	 SNDRV_PCM_FMTBIT_S24_3BE | \
+	 SNDRV_PCM_FMTBIT_S24_BE)
+#else
+#define FSLSSI_I2S_FORMATS \
+	(SNDRV_PCM_FMTBIT_S8 | \
+	 SNDRV_PCM_FMTBIT_S16_LE | \
+	 SNDRV_PCM_FMTBIT_S18_3LE | \
+	 SNDRV_PCM_FMTBIT_S20_3LE | \
+	 SNDRV_PCM_FMTBIT_S24_3LE | \
+	 SNDRV_PCM_FMTBIT_S24_LE)
+#endif
+
+/*
+ * In AC97 mode, TXDIR bit is forced to 0 and TFDIR bit is forced to 1:
+ *  - SSI inputs external bit clock and outputs frame sync clock -- CBM_CFS
+ *  - Also have NB_NF to mark these two clocks will not be inverted
+ */
+#define FSLSSI_AC97_DAIFMT \
+	(SND_SOC_DAIFMT_AC97 | \
+	 SND_SOC_DAIFMT_BC_FP | \
+	 SND_SOC_DAIFMT_NB_NF)
+
+#define FSLSSI_SIER_DBG_RX_FLAGS \
+	(SSI_SIER_RFF0_EN | \
+	 SSI_SIER_RLS_EN | \
+	 SSI_SIER_RFS_EN | \
+	 SSI_SIER_ROE0_EN | \
+	 SSI_SIER_RFRC_EN)
+#define FSLSSI_SIER_DBG_TX_FLAGS \
+	(SSI_SIER_TFE0_EN | \
+	 SSI_SIER_TLS_EN | \
+	 SSI_SIER_TFS_EN | \
+	 SSI_SIER_TUE0_EN | \
+	 SSI_SIER_TFRC_EN)
+
+enum fsl_ssi_type {
+	FSL_SSI_MCP8610,
+	FSL_SSI_MX21,
+	FSL_SSI_MX35,
+	FSL_SSI_MX51,
+};
+
+struct fsl_ssi_regvals {
+	u32 sier;
+	u32 srcr;
+	u32 stcr;
+	u32 scr;
+};
+
+static bool fsl_ssi_readable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case REG_SSI_SACCEN:
+	case REG_SSI_SACCDIS:
+		return false;
+	default:
+		return true;
+	}
+}
+
+static bool fsl_ssi_volatile_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case REG_SSI_STX0:
+	case REG_SSI_STX1:
+	case REG_SSI_SRX0:
+	case REG_SSI_SRX1:
+	case REG_SSI_SISR:
+	case REG_SSI_SFCSR:
+	case REG_SSI_SACNT:
+	case REG_SSI_SACADD:
+	case REG_SSI_SACDAT:
+	case REG_SSI_SATAG:
+	case REG_SSI_SACCST:
+	case REG_SSI_SOR:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool fsl_ssi_precious_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case REG_SSI_SRX0:
+	case REG_SSI_SRX1:
+	case REG_SSI_SISR:
+	case REG_SSI_SACADD:
+	case REG_SSI_SACDAT:
+	case REG_SSI_SATAG:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool fsl_ssi_writeable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case REG_SSI_SRX0:
+	case REG_SSI_SRX1:
+	case REG_SSI_SACCST:
+		return false;
+	default:
+		return true;
+	}
+}
+
+static const struct regmap_config fsl_ssi_regconfig = {
+	.max_register = REG_SSI_SACCDIS,
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.val_format_endian = REGMAP_ENDIAN_NATIVE,
+	.num_reg_defaults_raw = REG_SSI_SACCDIS / sizeof(uint32_t) + 1,
+	.readable_reg = fsl_ssi_readable_reg,
+	.volatile_reg = fsl_ssi_volatile_reg,
+	.precious_reg = fsl_ssi_precious_reg,
+	.writeable_reg = fsl_ssi_writeable_reg,
+	.cache_type = REGCACHE_FLAT,
+};
+
+struct fsl_ssi_soc_data {
+	bool imx;
+	bool imx21regs; /* imx21-class SSI - no SACC{ST,EN,DIS} regs */
+	bool offline_config;
+	u32 sisr_write_mask;
+};
+
+/**
+ * struct fsl_ssi - per-SSI private data
+ * @regs: Pointer to the regmap registers
+ * @irq: IRQ of this SSI
+ * @cpu_dai_drv: CPU DAI driver for this device
+ * @dai_fmt: DAI configuration this device is currently used with
+ * @streams: Mask of current active streams: BIT(TX) and BIT(RX)
+ * @i2s_net: I2S and Network mode configurations of SCR register
+ *           (this is the initial settings based on the DAI format)
+ * @synchronous: Use synchronous mode - both of TX and RX use STCK and SFCK
+ * @use_dma: DMA is used or FIQ with stream filter
+ * @use_dual_fifo: DMA with support for dual FIFO mode
+ * @use_dyna_fifo: DMA with support for multi FIFO script
+ * @has_ipg_clk_name: If "ipg" is in the clock name list of device tree
+ * @fifo_depth: Depth of the SSI FIFOs
+ * @slot_width: Width of each DAI slot
+ * @slots: Number of slots
+ * @regvals: Specific RX/TX register settings
+ * @clk: Clock source to access register
+ * @baudclk: Clock source to generate bit and frame-sync clocks
+ * @baudclk_streams: Active streams that are using baudclk
+ * @regcache_sfcsr: Cache sfcsr register value during suspend and resume
+ * @regcache_sacnt: Cache sacnt register value during suspend and resume
+ * @dma_params_tx: DMA transmit parameters
+ * @dma_params_rx: DMA receive parameters
+ * @ssi_phys: physical address of the SSI registers
+ * @fiq_params: FIQ stream filtering parameters
+ * @card_pdev: Platform_device pointer to register a sound card for PowerPC or
+ *             to register a CODEC platform device for AC97
+ * @card_name: Platform_device name to register a sound card for PowerPC or
+ *             to register a CODEC platform device for AC97
+ * @card_idx: The index of SSI to register a sound card for PowerPC or
+ *            to register a CODEC platform device for AC97
+ * @dbg_stats: Debugging statistics
+ * @soc: SoC specific data
+ * @dev: Pointer to &pdev->dev
+ * @fifo_watermark: The FIFO watermark setting. Notifies DMA when there are
+ *                  @fifo_watermark or fewer words in TX fifo or
+ *                  @fifo_watermark or more empty words in RX fifo.
+ * @dma_maxburst: Max number of words to transfer in one go. So far,
+ *                this is always the same as fifo_watermark.
+ * @ac97_reg_lock: Mutex lock to serialize AC97 register access operations
+ * @audio_config: configure for dma multi fifo script
+ */
+struct fsl_ssi {
+	struct regmap *regs;
+	int irq;
+	struct snd_soc_dai_driver cpu_dai_drv;
+
+	unsigned int dai_fmt;
+	u8 streams;
+	u8 i2s_net;
+	bool synchronous;
+	bool use_dma;
+	bool use_dual_fifo;
+	bool use_dyna_fifo;
+	bool has_ipg_clk_name;
+	unsigned int fifo_depth;
+	unsigned int slot_width;
+	unsigned int slots;
+	struct fsl_ssi_regvals regvals[2];
+
+	struct clk *clk;
+	struct clk *baudclk;
+	unsigned int baudclk_streams;
+
+	u32 regcache_sfcsr;
+	u32 regcache_sacnt;
+
+	struct snd_dmaengine_dai_dma_data dma_params_tx;
+	struct snd_dmaengine_dai_dma_data dma_params_rx;
+	dma_addr_t ssi_phys;
+
+	struct imx_pcm_fiq_params fiq_params;
+
+	struct platform_device *card_pdev;
+	char card_name[32];
+	u32 card_idx;
+
+	struct fsl_ssi_dbg dbg_stats;
+
+	const struct fsl_ssi_soc_data *soc;
+	struct device *dev;
+
+	u32 fifo_watermark;
+	u32 dma_maxburst;
+
+	struct mutex ac97_reg_lock;
+	struct sdma_peripheral_config audio_config[2];
+};
+
+/*
+ * SoC specific data
+ *
+ * Notes:
+ * 1) SSI in earlier SoCS has critical bits in control registers that
+ *    cannot be changed after SSI starts running -- a software reset
+ *    (set SSIEN to 0) is required to change their values. So adding
+ *    an offline_config flag for these SoCs.
+ * 2) SDMA is available since imx35. However, imx35 does not support
+ *    DMA bits changing when SSI is running, so set offline_config.
+ * 3) imx51 and later versions support register configurations when
+ *    SSI is running (SSIEN); For these versions, DMA needs to be
+ *    configured before SSI sends DMA request to avoid an undefined
+ *    DMA request on the SDMA side.
+ */
+
+static struct fsl_ssi_soc_data fsl_ssi_mpc8610 = {
+	.imx = false,
+	.offline_config = true,
+	.sisr_write_mask = SSI_SISR_RFRC | SSI_SISR_TFRC |
+			   SSI_SISR_ROE0 | SSI_SISR_ROE1 |
+			   SSI_SISR_TUE0 | SSI_SISR_TUE1,
+};
+
+static struct fsl_ssi_soc_data fsl_ssi_imx21 = {
+	.imx = true,
+	.imx21regs = true,
+	.offline_config = true,
+	.sisr_write_mask = 0,
+};
+
+static struct fsl_ssi_soc_data fsl_ssi_imx35 = {
+	.imx = true,
+	.offline_config = true,
+	.sisr_write_mask = SSI_SISR_RFRC | SSI_SISR_TFRC |
+			   SSI_SISR_ROE0 | SSI_SISR_ROE1 |
+			   SSI_SISR_TUE0 | SSI_SISR_TUE1,
+};
+
+static struct fsl_ssi_soc_data fsl_ssi_imx51 = {
+	.imx = true,
+	.offline_config = false,
+	.sisr_write_mask = SSI_SISR_ROE0 | SSI_SISR_ROE1 |
+			   SSI_SISR_TUE0 | SSI_SISR_TUE1,
+};
+
+static const struct of_device_id fsl_ssi_ids[] = {
+	{ .compatible = "fsl,mpc8610-ssi", .data = &fsl_ssi_mpc8610 },
+	{ .compatible = "fsl,imx51-ssi", .data = &fsl_ssi_imx51 },
+	{ .compatible = "fsl,imx35-ssi", .data = &fsl_ssi_imx35 },
+	{ .compatible = "fsl,imx21-ssi", .data = &fsl_ssi_imx21 },
+	{}
+};
+MODULE_DEVICE_TABLE(of, fsl_ssi_ids);
+
+static bool fsl_ssi_is_ac97(struct fsl_ssi *ssi)
+{
+	return (ssi->dai_fmt & SND_SOC_DAIFMT_FORMAT_MASK) ==
+		SND_SOC_DAIFMT_AC97;
+}
+
+static bool fsl_ssi_is_i2s_clock_provider(struct fsl_ssi *ssi)
+{
+	return (ssi->dai_fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) ==
+		SND_SOC_DAIFMT_BP_FP;
+}
+
+static bool fsl_ssi_is_i2s_bc_fp(struct fsl_ssi *ssi)
+{
+	return (ssi->dai_fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) ==
+		SND_SOC_DAIFMT_BC_FP;
+}
+
+/**
+ * fsl_ssi_isr - Interrupt handler to gather states
+ * @irq: irq number
+ * @dev_id: context
+ */
+static irqreturn_t fsl_ssi_isr(int irq, void *dev_id)
+{
+	struct fsl_ssi *ssi = dev_id;
+	struct regmap *regs = ssi->regs;
+	u32 sisr, sisr2;
+
+	regmap_read(regs, REG_SSI_SISR, &sisr);
+
+	sisr2 = sisr & ssi->soc->sisr_write_mask;
+	/* Clear the bits that we set */
+	if (sisr2)
+		regmap_write(regs, REG_SSI_SISR, sisr2);
+
+	fsl_ssi_dbg_isr(&ssi->dbg_stats, sisr);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * fsl_ssi_config_enable - Set SCR, SIER, STCR and SRCR registers with
+ * cached values in regvals
+ * @ssi: SSI context
+ * @tx: direction
+ *
+ * Notes:
+ * 1) For offline_config SoCs, enable all necessary bits of both streams
+ *    when 1st stream starts, even if the opposite stream will not start
+ * 2) It also clears FIFO before setting regvals; SOR is safe to set online
+ */
+static void fsl_ssi_config_enable(struct fsl_ssi *ssi, bool tx)
+{
+	struct fsl_ssi_regvals *vals = ssi->regvals;
+	int dir = tx ? TX : RX;
+	u32 sier, srcr, stcr;
+
+	/* Clear dirty data in the FIFO; It also prevents channel slipping */
+	regmap_update_bits(ssi->regs, REG_SSI_SOR,
+			   SSI_SOR_xX_CLR(tx), SSI_SOR_xX_CLR(tx));
+
+	/*
+	 * On offline_config SoCs, SxCR and SIER are already configured when
+	 * the previous stream started. So skip all SxCR and SIER settings
+	 * to prevent online reconfigurations, then jump to set SCR directly
+	 */
+	if (ssi->soc->offline_config && ssi->streams)
+		goto enable_scr;
+
+	if (ssi->soc->offline_config) {
+		/*
+		 * Online reconfiguration not supported, so enable all bits for
+		 * both streams at once to avoid necessity of reconfigurations
+		 */
+		srcr = vals[RX].srcr | vals[TX].srcr;
+		stcr = vals[RX].stcr | vals[TX].stcr;
+		sier = vals[RX].sier | vals[TX].sier;
+	} else {
+		/* Otherwise, only set bits for the current stream */
+		srcr = vals[dir].srcr;
+		stcr = vals[dir].stcr;
+		sier = vals[dir].sier;
+	}
+
+	/* Configure SRCR, STCR and SIER at once */
+	regmap_update_bits(ssi->regs, REG_SSI_SRCR, srcr, srcr);
+	regmap_update_bits(ssi->regs, REG_SSI_STCR, stcr, stcr);
+	regmap_update_bits(ssi->regs, REG_SSI_SIER, sier, sier);
+
+enable_scr:
+	/*
+	 * Start DMA before setting TE to avoid FIFO underrun
+	 * which may cause a channel slip or a channel swap
+	 *
+	 * TODO: FIQ cases might also need this upon testing
+	 */
+	if (ssi->use_dma && tx) {
+		int try = 100;
+		u32 sfcsr;
+
+		/* Enable SSI first to send TX DMA request */
+		regmap_update_bits(ssi->regs, REG_SSI_SCR,
+				   SSI_SCR_SSIEN, SSI_SCR_SSIEN);
+
+		/* Busy wait until TX FIFO not empty -- DMA working */
+		do {
+			regmap_read(ssi->regs, REG_SSI_SFCSR, &sfcsr);
+			if (SSI_SFCSR_TFCNT0(sfcsr))
+				break;
+		} while (--try);
+
+		/* FIFO still empty -- something might be wrong */
+		if (!SSI_SFCSR_TFCNT0(sfcsr))
+			dev_warn(ssi->dev, "Timeout waiting TX FIFO filling\n");
+	}
+	/* Enable all remaining bits in SCR */
+	regmap_update_bits(ssi->regs, REG_SSI_SCR,
+			   vals[dir].scr, vals[dir].scr);
+
+	/* Log the enabled stream to the mask */
+	ssi->streams |= BIT(dir);
+}
+
+/*
+ * Exclude bits that are used by the opposite stream
+ *
+ * When both streams are active, disabling some bits for the current stream
+ * might break the other stream if these bits are used by it.
+ *
+ * @vals : regvals of the current stream
+ * @avals: regvals of the opposite stream
+ * @aactive: active state of the opposite stream
+ *
+ *  1) XOR vals and avals to get the differences if the other stream is active;
+ *     Otherwise, return current vals if the other stream is not active
+ *  2) AND the result of 1) with the current vals
+ */
+#define _ssi_xor_shared_bits(vals, avals, aactive) \
+	((vals) ^ ((avals) * (aactive)))
+
+#define ssi_excl_shared_bits(vals, avals, aactive) \
+	((vals) & _ssi_xor_shared_bits(vals, avals, aactive))
+
+/**
+ * fsl_ssi_config_disable - Unset SCR, SIER, STCR and SRCR registers
+ * with cached values in regvals
+ * @ssi: SSI context
+ * @tx: direction
+ *
+ * Notes:
+ * 1) For offline_config SoCs, to avoid online reconfigurations, disable all
+ *    bits of both streams at once when the last stream is abort to end
+ * 2) It also clears FIFO after unsetting regvals; SOR is safe to set online
+ */
+static void fsl_ssi_config_disable(struct fsl_ssi *ssi, bool tx)
+{
+	struct fsl_ssi_regvals *vals, *avals;
+	u32 sier, srcr, stcr, scr;
+	int adir = tx ? RX : TX;
+	int dir = tx ? TX : RX;
+	bool aactive;
+
+	/* Check if the opposite stream is active */
+	aactive = ssi->streams & BIT(adir);
+
+	vals = &ssi->regvals[dir];
+
+	/* Get regvals of the opposite stream to keep opposite stream safe */
+	avals = &ssi->regvals[adir];
+
+	/*
+	 * To keep the other stream safe, exclude shared bits between
+	 * both streams, and get safe bits to disable current stream
+	 */
+	scr = ssi_excl_shared_bits(vals->scr, avals->scr, aactive);
+
+	/* Disable safe bits of SCR register for the current stream */
+	regmap_update_bits(ssi->regs, REG_SSI_SCR, scr, 0);
+
+	/* Log the disabled stream to the mask */
+	ssi->streams &= ~BIT(dir);
+
+	/*
+	 * On offline_config SoCs, if the other stream is active, skip
+	 * SxCR and SIER settings to prevent online reconfigurations
+	 */
+	if (ssi->soc->offline_config && aactive)
+		goto fifo_clear;
+
+	if (ssi->soc->offline_config) {
+		/* Now there is only current stream active, disable all bits */
+		srcr = vals->srcr | avals->srcr;
+		stcr = vals->stcr | avals->stcr;
+		sier = vals->sier | avals->sier;
+	} else {
+		/*
+		 * To keep the other stream safe, exclude shared bits between
+		 * both streams, and get safe bits to disable current stream
+		 */
+		sier = ssi_excl_shared_bits(vals->sier, avals->sier, aactive);
+		srcr = ssi_excl_shared_bits(vals->srcr, avals->srcr, aactive);
+		stcr = ssi_excl_shared_bits(vals->stcr, avals->stcr, aactive);
+	}
+
+	/* Clear configurations of SRCR, STCR and SIER at once */
+	regmap_update_bits(ssi->regs, REG_SSI_SRCR, srcr, 0);
+	regmap_update_bits(ssi->regs, REG_SSI_STCR, stcr, 0);
+	regmap_update_bits(ssi->regs, REG_SSI_SIER, sier, 0);
+
+fifo_clear:
+	/* Clear remaining data in the FIFO */
+	regmap_update_bits(ssi->regs, REG_SSI_SOR,
+			   SSI_SOR_xX_CLR(tx), SSI_SOR_xX_CLR(tx));
+}
+
+static void fsl_ssi_tx_ac97_saccst_setup(struct fsl_ssi *ssi)
+{
+	struct regmap *regs = ssi->regs;
+
+	/* no SACC{ST,EN,DIS} regs on imx21-class SSI */
+	if (!ssi->soc->imx21regs) {
+		/* Disable all channel slots */
+		regmap_write(regs, REG_SSI_SACCDIS, 0xff);
+		/* Enable slots 3 & 4 -- PCM Playback Left & Right channels */
+		regmap_write(regs, REG_SSI_SACCEN, 0x300);
+	}
+}
+
+/**
+ * fsl_ssi_setup_regvals - Cache critical bits of SIER, SRCR, STCR and
+ * SCR to later set them safely
+ * @ssi: SSI context
+ */
+static void fsl_ssi_setup_regvals(struct fsl_ssi *ssi)
+{
+	struct fsl_ssi_regvals *vals = ssi->regvals;
+
+	vals[RX].sier = SSI_SIER_RFF0_EN | FSLSSI_SIER_DBG_RX_FLAGS;
+	vals[RX].srcr = SSI_SRCR_RFEN0;
+	vals[RX].scr = SSI_SCR_SSIEN | SSI_SCR_RE;
+	vals[TX].sier = SSI_SIER_TFE0_EN | FSLSSI_SIER_DBG_TX_FLAGS;
+	vals[TX].stcr = SSI_STCR_TFEN0;
+	vals[TX].scr = SSI_SCR_SSIEN | SSI_SCR_TE;
+
+	/* AC97 has already enabled SSIEN, RE and TE, so ignore them */
+	if (fsl_ssi_is_ac97(ssi))
+		vals[RX].scr = vals[TX].scr = 0;
+
+	if (ssi->use_dual_fifo) {
+		vals[RX].srcr |= SSI_SRCR_RFEN1;
+		vals[TX].stcr |= SSI_STCR_TFEN1;
+	}
+
+	if (ssi->use_dma) {
+		vals[RX].sier |= SSI_SIER_RDMAE;
+		vals[TX].sier |= SSI_SIER_TDMAE;
+	} else {
+		vals[RX].sier |= SSI_SIER_RIE;
+		vals[TX].sier |= SSI_SIER_TIE;
+	}
+}
+
+static void fsl_ssi_setup_ac97(struct fsl_ssi *ssi)
+{
+	struct regmap *regs = ssi->regs;
+
+	/* Setup the clock control register */
+	regmap_write(regs, REG_SSI_STCCR, SSI_SxCCR_WL(17) | SSI_SxCCR_DC(13));
+	regmap_write(regs, REG_SSI_SRCCR, SSI_SxCCR_WL(17) | SSI_SxCCR_DC(13));
+
+	/* Enable AC97 mode and startup the SSI */
+	regmap_write(regs, REG_SSI_SACNT, SSI_SACNT_AC97EN | SSI_SACNT_FV);
+
+	/* AC97 has to communicate with codec before starting a stream */
+	regmap_update_bits(regs, REG_SSI_SCR,
+			   SSI_SCR_SSIEN | SSI_SCR_TE | SSI_SCR_RE,
+			   SSI_SCR_SSIEN | SSI_SCR_TE | SSI_SCR_RE);
+
+	regmap_write(regs, REG_SSI_SOR, SSI_SOR_WAIT(3));
+}
+
+static int fsl_ssi_startup(struct snd_pcm_substream *substream,
+			   struct snd_soc_dai *dai)
+{
+	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
+	struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(asoc_rtd_to_cpu(rtd, 0));
+	int ret;
+
+	ret = clk_prepare_enable(ssi->clk);
+	if (ret)
+		return ret;
+
+	/*
+	 * When using dual fifo mode, it is safer to ensure an even period
+	 * size. If appearing to an odd number while DMA always starts its
+	 * task from fifo0, fifo1 would be neglected at the end of each
+	 * period. But SSI would still access fifo1 with an invalid data.
+	 */
+	if (ssi->use_dual_fifo || ssi->use_dyna_fifo)
+		snd_pcm_hw_constraint_step(substream->runtime, 0,
+					   SNDRV_PCM_HW_PARAM_PERIOD_SIZE, 2);
+
+	return 0;
+}
+
+static void fsl_ssi_shutdown(struct snd_pcm_substream *substream,
+			     struct snd_soc_dai *dai)
+{
+	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
+	struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(asoc_rtd_to_cpu(rtd, 0));
+
+	clk_disable_unprepare(ssi->clk);
+}
+
+/**
+ * fsl_ssi_set_bclk - Configure Digital Audio Interface bit clock
+ * @substream: ASoC substream
+ * @dai: pointer to DAI
+ * @hw_params: pointers to hw_params
+ *
+ * Notes: This function can be only called when using SSI as DAI master
+ *
+ * Quick instruction for parameters:
+ * freq: Output BCLK frequency = samplerate * slots * slot_width
+ *       (In 2-channel I2S Master mode, slot_width is fixed 32)
+ */
+static int fsl_ssi_set_bclk(struct snd_pcm_substream *substream,
+			    struct snd_soc_dai *dai,
+			    struct snd_pcm_hw_params *hw_params)
+{
+	bool tx2, tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK;
+	struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai);
+	struct regmap *regs = ssi->regs;
+	u32 pm = 999, div2, psr, stccr, mask, afreq, factor, i;
+	unsigned long clkrate, baudrate, tmprate;
+	unsigned int channels = params_channels(hw_params);
+	unsigned int slot_width = params_width(hw_params);
+	unsigned int slots = 2;
+	u64 sub, savesub = 100000;
+	unsigned int freq;
+	bool baudclk_is_used;
+	int ret;
+
+	/* Override slots and slot_width if being specifically set... */
+	if (ssi->slots)
+		slots = ssi->slots;
+	if (ssi->slot_width)
+		slot_width = ssi->slot_width;
+
+	/* ...but force 32 bits for stereo audio using I2S Master Mode */
+	if (channels == 2 &&
+	    (ssi->i2s_net & SSI_SCR_I2S_MODE_MASK) == SSI_SCR_I2S_MODE_MASTER)
+		slot_width = 32;
+
+	/* Generate bit clock based on the slot number and slot width */
+	freq = slots * slot_width * params_rate(hw_params);
+
+	/* Don't apply it to any non-baudclk circumstance */
+	if (IS_ERR(ssi->baudclk))
+		return -EINVAL;
+
+	/*
+	 * Hardware limitation: The bclk rate must be
+	 * never greater than 1/5 IPG clock rate
+	 */
+	if (freq * 5 > clk_get_rate(ssi->clk)) {
+		dev_err(dai->dev, "bitclk > ipgclk / 5\n");
+		return -EINVAL;
+	}
+
+	baudclk_is_used = ssi->baudclk_streams & ~(BIT(substream->stream));
+
+	/* It should be already enough to divide clock by setting pm alone */
+	psr = 0;
+	div2 = 0;
+
+	factor = (div2 + 1) * (7 * psr + 1) * 2;
+
+	for (i = 0; i < 255; i++) {
+		tmprate = freq * factor * (i + 1);
+
+		if (baudclk_is_used)
+			clkrate = clk_get_rate(ssi->baudclk);
+		else
+			clkrate = clk_round_rate(ssi->baudclk, tmprate);
+
+		clkrate /= factor;
+		afreq = clkrate / (i + 1);
+
+		if (freq == afreq)
+			sub = 0;
+		else if (freq / afreq == 1)
+			sub = freq - afreq;
+		else if (afreq / freq == 1)
+			sub = afreq - freq;
+		else
+			continue;
+
+		/* Calculate the fraction */
+		sub *= 100000;
+		do_div(sub, freq);
+
+		if (sub < savesub && !(i == 0)) {
+			baudrate = tmprate;
+			savesub = sub;
+			pm = i;
+		}
+
+		/* We are lucky */
+		if (savesub == 0)
+			break;
+	}
+
+	/* No proper pm found if it is still remaining the initial value */
+	if (pm == 999) {
+		dev_err(dai->dev, "failed to handle the required sysclk\n");
+		return -EINVAL;
+	}
+
+	stccr = SSI_SxCCR_PM(pm + 1);
+	mask = SSI_SxCCR_PM_MASK | SSI_SxCCR_DIV2 | SSI_SxCCR_PSR;
+
+	/* STCCR is used for RX in synchronous mode */
+	tx2 = tx || ssi->synchronous;
+	regmap_update_bits(regs, REG_SSI_SxCCR(tx2), mask, stccr);
+
+	if (!baudclk_is_used) {
+		ret = clk_set_rate(ssi->baudclk, baudrate);
+		if (ret) {
+			dev_err(dai->dev, "failed to set baudclk rate\n");
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * fsl_ssi_hw_params - Configure SSI based on PCM hardware parameters
+ * @substream: ASoC substream
+ * @hw_params: pointers to hw_params
+ * @dai: pointer to DAI
+ *
+ * Notes:
+ * 1) SxCCR.WL bits are critical bits that require SSI to be temporarily
+ *    disabled on offline_config SoCs. Even for online configurable SoCs
+ *    running in synchronous mode (both TX and RX use STCCR), it is not
+ *    safe to re-configure them when both two streams start running.
+ * 2) SxCCR.PM, SxCCR.DIV2 and SxCCR.PSR bits will be configured in the
+ *    fsl_ssi_set_bclk() if SSI is the DAI clock master.
+ */
+static int fsl_ssi_hw_params(struct snd_pcm_substream *substream,
+			     struct snd_pcm_hw_params *hw_params,
+			     struct snd_soc_dai *dai)
+{
+	bool tx2, tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK;
+	struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai);
+	struct fsl_ssi_regvals *vals = ssi->regvals;
+	struct regmap *regs = ssi->regs;
+	unsigned int channels = params_channels(hw_params);
+	unsigned int sample_size = params_width(hw_params);
+	u32 wl = SSI_SxCCR_WL(sample_size);
+	int ret;
+
+	if (fsl_ssi_is_i2s_clock_provider(ssi)) {
+		ret = fsl_ssi_set_bclk(substream, dai, hw_params);
+		if (ret)
+			return ret;
+
+		/* Do not enable the clock if it is already enabled */
+		if (!(ssi->baudclk_streams & BIT(substream->stream))) {
+			ret = clk_prepare_enable(ssi->baudclk);
+			if (ret)
+				return ret;
+
+			ssi->baudclk_streams |= BIT(substream->stream);
+		}
+	}
+
+	/*
+	 * SSI is properly configured if it is enabled and running in
+	 * the synchronous mode; Note that AC97 mode is an exception
+	 * that should set separate configurations for STCCR and SRCCR
+	 * despite running in the synchronous mode.
+	 */
+	if (ssi->streams && ssi->synchronous)
+		return 0;
+
+	if (!fsl_ssi_is_ac97(ssi)) {
+		/*
+		 * Keep the ssi->i2s_net intact while having a local variable
+		 * to override settings for special use cases. Otherwise, the
+		 * ssi->i2s_net will lose the settings for regular use cases.
+		 */
+		u8 i2s_net = ssi->i2s_net;
+
+		/* Normal + Network mode to send 16-bit data in 32-bit frames */
+		if (fsl_ssi_is_i2s_bc_fp(ssi) && sample_size == 16)
+			i2s_net = SSI_SCR_I2S_MODE_NORMAL | SSI_SCR_NET;
+
+		/* Use Normal mode to send mono data at 1st slot of 2 slots */
+		if (channels == 1)
+			i2s_net = SSI_SCR_I2S_MODE_NORMAL;
+
+		regmap_update_bits(regs, REG_SSI_SCR,
+				   SSI_SCR_I2S_NET_MASK, i2s_net);
+	}
+
+	/* In synchronous mode, the SSI uses STCCR for capture */
+	tx2 = tx || ssi->synchronous;
+	regmap_update_bits(regs, REG_SSI_SxCCR(tx2), SSI_SxCCR_WL_MASK, wl);
+
+	if (ssi->use_dyna_fifo) {
+		if (channels == 1) {
+			ssi->audio_config[0].n_fifos_dst = 1;
+			ssi->audio_config[1].n_fifos_src = 1;
+			vals[RX].srcr &= ~SSI_SRCR_RFEN1;
+			vals[TX].stcr &= ~SSI_STCR_TFEN1;
+			vals[RX].scr  &= ~SSI_SCR_TCH_EN;
+			vals[TX].scr  &= ~SSI_SCR_TCH_EN;
+		} else {
+			ssi->audio_config[0].n_fifos_dst = 2;
+			ssi->audio_config[1].n_fifos_src = 2;
+			vals[RX].srcr |= SSI_SRCR_RFEN1;
+			vals[TX].stcr |= SSI_STCR_TFEN1;
+			vals[RX].scr  |= SSI_SCR_TCH_EN;
+			vals[TX].scr  |= SSI_SCR_TCH_EN;
+		}
+		ssi->dma_params_tx.peripheral_config = &ssi->audio_config[0];
+		ssi->dma_params_tx.peripheral_size = sizeof(ssi->audio_config[0]);
+		ssi->dma_params_rx.peripheral_config = &ssi->audio_config[1];
+		ssi->dma_params_rx.peripheral_size = sizeof(ssi->audio_config[1]);
+	}
+
+	return 0;
+}
+
+static int fsl_ssi_hw_free(struct snd_pcm_substream *substream,
+			   struct snd_soc_dai *dai)
+{
+	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
+	struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(asoc_rtd_to_cpu(rtd, 0));
+
+	if (fsl_ssi_is_i2s_clock_provider(ssi) &&
+	    ssi->baudclk_streams & BIT(substream->stream)) {
+		clk_disable_unprepare(ssi->baudclk);
+		ssi->baudclk_streams &= ~BIT(substream->stream);
+	}
+
+	return 0;
+}
+
+static int _fsl_ssi_set_dai_fmt(struct fsl_ssi *ssi, unsigned int fmt)
+{
+	u32 strcr = 0, scr = 0, stcr, srcr, mask;
+	unsigned int slots;
+
+	ssi->dai_fmt = fmt;
+
+	/* Synchronize frame sync clock for TE to avoid data slipping */
+	scr |= SSI_SCR_SYNC_TX_FS;
+
+	/* Set to default shifting settings: LSB_ALIGNED */
+	strcr |= SSI_STCR_TXBIT0;
+
+	/* Use Network mode as default */
+	ssi->i2s_net = SSI_SCR_NET;
+	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
+	case SND_SOC_DAIFMT_I2S:
+		switch (fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) {
+		case SND_SOC_DAIFMT_BP_FP:
+			if (IS_ERR(ssi->baudclk)) {
+				dev_err(ssi->dev,
+					"missing baudclk for master mode\n");
+				return -EINVAL;
+			}
+			fallthrough;
+		case SND_SOC_DAIFMT_BC_FP:
+			ssi->i2s_net |= SSI_SCR_I2S_MODE_MASTER;
+			break;
+		case SND_SOC_DAIFMT_BC_FC:
+			ssi->i2s_net |= SSI_SCR_I2S_MODE_SLAVE;
+			break;
+		default:
+			return -EINVAL;
+		}
+
+		slots = ssi->slots ? : 2;
+		regmap_update_bits(ssi->regs, REG_SSI_STCCR,
+				   SSI_SxCCR_DC_MASK, SSI_SxCCR_DC(slots));
+		regmap_update_bits(ssi->regs, REG_SSI_SRCCR,
+				   SSI_SxCCR_DC_MASK, SSI_SxCCR_DC(slots));
+
+		/* Data on rising edge of bclk, frame low, 1clk before data */
+		strcr |= SSI_STCR_TFSI | SSI_STCR_TSCKP | SSI_STCR_TEFS;
+		break;
+	case SND_SOC_DAIFMT_LEFT_J:
+		/* Data on rising edge of bclk, frame high */
+		strcr |= SSI_STCR_TSCKP;
+		break;
+	case SND_SOC_DAIFMT_DSP_A:
+		/* Data on rising edge of bclk, frame high, 1clk before data */
+		strcr |= SSI_STCR_TFSL | SSI_STCR_TSCKP | SSI_STCR_TEFS;
+		break;
+	case SND_SOC_DAIFMT_DSP_B:
+		/* Data on rising edge of bclk, frame high */
+		strcr |= SSI_STCR_TFSL | SSI_STCR_TSCKP;
+		break;
+	case SND_SOC_DAIFMT_AC97:
+		/* Data on falling edge of bclk, frame high, 1clk before data */
+		strcr |= SSI_STCR_TEFS;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	scr |= ssi->i2s_net;
+
+	/* DAI clock inversion */
+	switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+	case SND_SOC_DAIFMT_NB_NF:
+		/* Nothing to do for both normal cases */
+		break;
+	case SND_SOC_DAIFMT_IB_NF:
+		/* Invert bit clock */
+		strcr ^= SSI_STCR_TSCKP;
+		break;
+	case SND_SOC_DAIFMT_NB_IF:
+		/* Invert frame clock */
+		strcr ^= SSI_STCR_TFSI;
+		break;
+	case SND_SOC_DAIFMT_IB_IF:
+		/* Invert both clocks */
+		strcr ^= SSI_STCR_TSCKP;
+		strcr ^= SSI_STCR_TFSI;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/* DAI clock provider masks */
+	switch (fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) {
+	case SND_SOC_DAIFMT_BP_FP:
+		/* Output bit and frame sync clocks */
+		strcr |= SSI_STCR_TFDIR | SSI_STCR_TXDIR;
+		scr |= SSI_SCR_SYS_CLK_EN;
+		break;
+	case SND_SOC_DAIFMT_BC_FC:
+		/* Input bit or frame sync clocks */
+		break;
+	case SND_SOC_DAIFMT_BC_FP:
+		/* Input bit clock but output frame sync clock */
+		strcr |= SSI_STCR_TFDIR;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	stcr = strcr;
+	srcr = strcr;
+
+	/* Set SYN mode and clear RXDIR bit when using SYN or AC97 mode */
+	if (ssi->synchronous || fsl_ssi_is_ac97(ssi)) {
+		srcr &= ~SSI_SRCR_RXDIR;
+		scr |= SSI_SCR_SYN;
+	}
+
+	mask = SSI_STCR_TFDIR | SSI_STCR_TXDIR | SSI_STCR_TSCKP |
+	       SSI_STCR_TFSL | SSI_STCR_TFSI | SSI_STCR_TEFS | SSI_STCR_TXBIT0;
+
+	regmap_update_bits(ssi->regs, REG_SSI_STCR, mask, stcr);
+	regmap_update_bits(ssi->regs, REG_SSI_SRCR, mask, srcr);
+
+	mask = SSI_SCR_SYNC_TX_FS | SSI_SCR_I2S_MODE_MASK |
+	       SSI_SCR_SYS_CLK_EN | SSI_SCR_SYN;
+	regmap_update_bits(ssi->regs, REG_SSI_SCR, mask, scr);
+
+	return 0;
+}
+
+/**
+ * fsl_ssi_set_dai_fmt - Configure Digital Audio Interface (DAI) Format
+ * @dai: pointer to DAI
+ * @fmt: format mask
+ */
+static int fsl_ssi_set_dai_fmt(struct snd_soc_dai *dai, unsigned int fmt)
+{
+	struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai);
+
+	/* AC97 configured DAIFMT earlier in the probe() */
+	if (fsl_ssi_is_ac97(ssi))
+		return 0;
+
+	return _fsl_ssi_set_dai_fmt(ssi, fmt);
+}
+
+/**
+ * fsl_ssi_set_dai_tdm_slot - Set TDM slot number and slot width
+ * @dai: pointer to DAI
+ * @tx_mask: mask for TX
+ * @rx_mask: mask for RX
+ * @slots: number of slots
+ * @slot_width: number of bits per slot
+ */
+static int fsl_ssi_set_dai_tdm_slot(struct snd_soc_dai *dai, u32 tx_mask,
+				    u32 rx_mask, int slots, int slot_width)
+{
+	struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai);
+	struct regmap *regs = ssi->regs;
+	u32 val;
+
+	/* The word length should be 8, 10, 12, 16, 18, 20, 22 or 24 */
+	if (slot_width & 1 || slot_width < 8 || slot_width > 24) {
+		dev_err(dai->dev, "invalid slot width: %d\n", slot_width);
+		return -EINVAL;
+	}
+
+	/* The slot number should be >= 2 if using Network mode or I2S mode */
+	if (ssi->i2s_net && slots < 2) {
+		dev_err(dai->dev, "slot number should be >= 2 in I2S or NET\n");
+		return -EINVAL;
+	}
+
+	regmap_update_bits(regs, REG_SSI_STCCR,
+			   SSI_SxCCR_DC_MASK, SSI_SxCCR_DC(slots));
+	regmap_update_bits(regs, REG_SSI_SRCCR,
+			   SSI_SxCCR_DC_MASK, SSI_SxCCR_DC(slots));
+
+	/* Save the SCR register value */
+	regmap_read(regs, REG_SSI_SCR, &val);
+	/* Temporarily enable SSI to allow SxMSKs to be configurable */
+	regmap_update_bits(regs, REG_SSI_SCR, SSI_SCR_SSIEN, SSI_SCR_SSIEN);
+
+	regmap_write(regs, REG_SSI_STMSK, ~tx_mask);
+	regmap_write(regs, REG_SSI_SRMSK, ~rx_mask);
+
+	/* Restore the value of SSIEN bit */
+	regmap_update_bits(regs, REG_SSI_SCR, SSI_SCR_SSIEN, val);
+
+	ssi->slot_width = slot_width;
+	ssi->slots = slots;
+
+	return 0;
+}
+
+/**
+ * fsl_ssi_trigger - Start or stop SSI and corresponding DMA transaction.
+ * @substream: ASoC substream
+ * @cmd: trigger command
+ * @dai: pointer to DAI
+ *
+ * The DMA channel is in external master start and pause mode, which
+ * means the SSI completely controls the flow of data.
+ */
+static int fsl_ssi_trigger(struct snd_pcm_substream *substream, int cmd,
+			   struct snd_soc_dai *dai)
+{
+	struct snd_soc_pcm_runtime *rtd = asoc_substream_to_rtd(substream);
+	struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(asoc_rtd_to_cpu(rtd, 0));
+	bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK;
+
+	switch (cmd) {
+	case SNDRV_PCM_TRIGGER_START:
+	case SNDRV_PCM_TRIGGER_RESUME:
+	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
+		/*
+		 * SACCST might be modified via AC Link by a CODEC if it sends
+		 * extra bits in their SLOTREQ requests, which'll accidentally
+		 * send valid data to slots other than normal playback slots.
+		 *
+		 * To be safe, configure SACCST right before TX starts.
+		 */
+		if (tx && fsl_ssi_is_ac97(ssi))
+			fsl_ssi_tx_ac97_saccst_setup(ssi);
+		fsl_ssi_config_enable(ssi, tx);
+		break;
+
+	case SNDRV_PCM_TRIGGER_STOP:
+	case SNDRV_PCM_TRIGGER_SUSPEND:
+	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
+		fsl_ssi_config_disable(ssi, tx);
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int fsl_ssi_dai_probe(struct snd_soc_dai *dai)
+{
+	struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai);
+
+	if (ssi->soc->imx && ssi->use_dma)
+		snd_soc_dai_init_dma_data(dai, &ssi->dma_params_tx,
+					  &ssi->dma_params_rx);
+
+	return 0;
+}
+
+static const struct snd_soc_dai_ops fsl_ssi_dai_ops = {
+	.probe = fsl_ssi_dai_probe,
+	.startup = fsl_ssi_startup,
+	.shutdown = fsl_ssi_shutdown,
+	.hw_params = fsl_ssi_hw_params,
+	.hw_free = fsl_ssi_hw_free,
+	.set_fmt = fsl_ssi_set_dai_fmt,
+	.set_tdm_slot = fsl_ssi_set_dai_tdm_slot,
+	.trigger = fsl_ssi_trigger,
+};
+
+static struct snd_soc_dai_driver fsl_ssi_dai_template = {
+	.playback = {
+		.stream_name = "CPU-Playback",
+		.channels_min = 1,
+		.channels_max = 32,
+		.rates = SNDRV_PCM_RATE_CONTINUOUS,
+		.formats = FSLSSI_I2S_FORMATS,
+	},
+	.capture = {
+		.stream_name = "CPU-Capture",
+		.channels_min = 1,
+		.channels_max = 32,
+		.rates = SNDRV_PCM_RATE_CONTINUOUS,
+		.formats = FSLSSI_I2S_FORMATS,
+	},
+	.ops = &fsl_ssi_dai_ops,
+};
+
+static const struct snd_soc_component_driver fsl_ssi_component = {
+	.name = "fsl-ssi",
+	.legacy_dai_naming = 1,
+};
+
+static struct snd_soc_dai_driver fsl_ssi_ac97_dai = {
+	.symmetric_channels = 1,
+	.playback = {
+		.stream_name = "CPU AC97 Playback",
+		.channels_min = 2,
+		.channels_max = 2,
+		.rates = SNDRV_PCM_RATE_8000_48000,
+		.formats = SNDRV_PCM_FMTBIT_S16 | SNDRV_PCM_FMTBIT_S20,
+	},
+	.capture = {
+		.stream_name = "CPU AC97 Capture",
+		.channels_min = 2,
+		.channels_max = 2,
+		.rates = SNDRV_PCM_RATE_48000,
+		/* 16-bit capture is broken (errata ERR003778) */
+		.formats = SNDRV_PCM_FMTBIT_S20,
+	},
+	.ops = &fsl_ssi_dai_ops,
+};
+
+static struct fsl_ssi *fsl_ac97_data;
+
+static void fsl_ssi_ac97_write(struct snd_ac97 *ac97, unsigned short reg,
+			       unsigned short val)
+{
+	struct regmap *regs = fsl_ac97_data->regs;
+	unsigned int lreg;
+	unsigned int lval;
+	int ret;
+
+	if (reg > 0x7f)
+		return;
+
+	mutex_lock(&fsl_ac97_data->ac97_reg_lock);
+
+	ret = clk_prepare_enable(fsl_ac97_data->clk);
+	if (ret) {
+		pr_err("ac97 write clk_prepare_enable failed: %d\n",
+			ret);
+		goto ret_unlock;
+	}
+
+	lreg = reg <<  12;
+	regmap_write(regs, REG_SSI_SACADD, lreg);
+
+	lval = val << 4;
+	regmap_write(regs, REG_SSI_SACDAT, lval);
+
+	regmap_update_bits(regs, REG_SSI_SACNT,
+			   SSI_SACNT_RDWR_MASK, SSI_SACNT_WR);
+	udelay(100);
+
+	clk_disable_unprepare(fsl_ac97_data->clk);
+
+ret_unlock:
+	mutex_unlock(&fsl_ac97_data->ac97_reg_lock);
+}
+
+static unsigned short fsl_ssi_ac97_read(struct snd_ac97 *ac97,
+					unsigned short reg)
+{
+	struct regmap *regs = fsl_ac97_data->regs;
+	unsigned short val = 0;
+	u32 reg_val;
+	unsigned int lreg;
+	int ret;
+
+	mutex_lock(&fsl_ac97_data->ac97_reg_lock);
+
+	ret = clk_prepare_enable(fsl_ac97_data->clk);
+	if (ret) {
+		pr_err("ac97 read clk_prepare_enable failed: %d\n", ret);
+		goto ret_unlock;
+	}
+
+	lreg = (reg & 0x7f) <<  12;
+	regmap_write(regs, REG_SSI_SACADD, lreg);
+	regmap_update_bits(regs, REG_SSI_SACNT,
+			   SSI_SACNT_RDWR_MASK, SSI_SACNT_RD);
+
+	udelay(100);
+
+	regmap_read(regs, REG_SSI_SACDAT, &reg_val);
+	val = (reg_val >> 4) & 0xffff;
+
+	clk_disable_unprepare(fsl_ac97_data->clk);
+
+ret_unlock:
+	mutex_unlock(&fsl_ac97_data->ac97_reg_lock);
+	return val;
+}
+
+static struct snd_ac97_bus_ops fsl_ssi_ac97_ops = {
+	.read = fsl_ssi_ac97_read,
+	.write = fsl_ssi_ac97_write,
+};
+
+/**
+ * fsl_ssi_hw_init - Initialize SSI registers
+ * @ssi: SSI context
+ */
+static int fsl_ssi_hw_init(struct fsl_ssi *ssi)
+{
+	u32 wm = ssi->fifo_watermark;
+
+	/* Initialize regvals */
+	fsl_ssi_setup_regvals(ssi);
+
+	/* Set watermarks */
+	regmap_write(ssi->regs, REG_SSI_SFCSR,
+		     SSI_SFCSR_TFWM0(wm) | SSI_SFCSR_RFWM0(wm) |
+		     SSI_SFCSR_TFWM1(wm) | SSI_SFCSR_RFWM1(wm));
+
+	/* Enable Dual FIFO mode */
+	if (ssi->use_dual_fifo)
+		regmap_update_bits(ssi->regs, REG_SSI_SCR,
+				   SSI_SCR_TCH_EN, SSI_SCR_TCH_EN);
+
+	/* AC97 should start earlier to communicate with CODECs */
+	if (fsl_ssi_is_ac97(ssi)) {
+		_fsl_ssi_set_dai_fmt(ssi, ssi->dai_fmt);
+		fsl_ssi_setup_ac97(ssi);
+	}
+
+	return 0;
+}
+
+/**
+ * fsl_ssi_hw_clean - Clear SSI registers
+ * @ssi: SSI context
+ */
+static void fsl_ssi_hw_clean(struct fsl_ssi *ssi)
+{
+	/* Disable registers for AC97 */
+	if (fsl_ssi_is_ac97(ssi)) {
+		/* Disable TE and RE bits first */
+		regmap_update_bits(ssi->regs, REG_SSI_SCR,
+				   SSI_SCR_TE | SSI_SCR_RE, 0);
+		/* Disable AC97 mode */
+		regmap_write(ssi->regs, REG_SSI_SACNT, 0);
+		/* Unset WAIT bits */
+		regmap_write(ssi->regs, REG_SSI_SOR, 0);
+		/* Disable SSI -- software reset */
+		regmap_update_bits(ssi->regs, REG_SSI_SCR, SSI_SCR_SSIEN, 0);
+	}
+}
+
+/*
+ * Make every character in a string lower-case
+ */
+static void make_lowercase(char *s)
+{
+	if (!s)
+		return;
+	for (; *s; s++)
+		*s = tolower(*s);
+}
+
+static int fsl_ssi_imx_probe(struct platform_device *pdev,
+			     struct fsl_ssi *ssi, void __iomem *iomem)
+{
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	/* Backward compatible for a DT without ipg clock name assigned */
+	if (ssi->has_ipg_clk_name)
+		ssi->clk = devm_clk_get(dev, "ipg");
+	else
+		ssi->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(ssi->clk)) {
+		ret = PTR_ERR(ssi->clk);
+		dev_err(dev, "failed to get clock: %d\n", ret);
+		return ret;
+	}
+
+	/* Enable the clock since regmap will not handle it in this case */
+	if (!ssi->has_ipg_clk_name) {
+		ret = clk_prepare_enable(ssi->clk);
+		if (ret) {
+			dev_err(dev, "clk_prepare_enable failed: %d\n", ret);
+			return ret;
+		}
+	}
+
+	/* Do not error out for consumer cases that live without a baud clock */
+	ssi->baudclk = devm_clk_get(dev, "baud");
+	if (IS_ERR(ssi->baudclk))
+		dev_dbg(dev, "failed to get baud clock: %ld\n",
+			 PTR_ERR(ssi->baudclk));
+
+	ssi->dma_params_tx.maxburst = ssi->dma_maxburst;
+	ssi->dma_params_rx.maxburst = ssi->dma_maxburst;
+	ssi->dma_params_tx.addr = ssi->ssi_phys + REG_SSI_STX0;
+	ssi->dma_params_rx.addr = ssi->ssi_phys + REG_SSI_SRX0;
+
+	/* Use even numbers to avoid channel swap due to SDMA script design */
+	if (ssi->use_dual_fifo || ssi->use_dyna_fifo) {
+		ssi->dma_params_tx.maxburst &= ~0x1;
+		ssi->dma_params_rx.maxburst &= ~0x1;
+	}
+
+	if (!ssi->use_dma) {
+		/*
+		 * Some boards use an incompatible codec. Use imx-fiq-pcm-audio
+		 * to get it working, as DMA is not possible in this situation.
+		 */
+		ssi->fiq_params.irq = ssi->irq;
+		ssi->fiq_params.base = iomem;
+		ssi->fiq_params.dma_params_rx = &ssi->dma_params_rx;
+		ssi->fiq_params.dma_params_tx = &ssi->dma_params_tx;
+
+		ret = imx_pcm_fiq_init(pdev, &ssi->fiq_params);
+		if (ret)
+			goto error_pcm;
+	} else {
+		ret = imx_pcm_dma_init(pdev);
+		if (ret)
+			goto error_pcm;
+	}
+
+	return 0;
+
+error_pcm:
+	if (!ssi->has_ipg_clk_name)
+		clk_disable_unprepare(ssi->clk);
+
+	return ret;
+}
+
+static void fsl_ssi_imx_clean(struct platform_device *pdev, struct fsl_ssi *ssi)
+{
+	if (!ssi->use_dma)
+		imx_pcm_fiq_exit(pdev);
+	if (!ssi->has_ipg_clk_name)
+		clk_disable_unprepare(ssi->clk);
+}
+
+static int fsl_ssi_probe_from_dt(struct fsl_ssi *ssi)
+{
+	struct device *dev = ssi->dev;
+	struct device_node *np = dev->of_node;
+	const char *p, *sprop;
+	const __be32 *iprop;
+	u32 dmas[4];
+	int ret;
+
+	ret = of_property_match_string(np, "clock-names", "ipg");
+	/* Get error code if not found */
+	ssi->has_ipg_clk_name = ret >= 0;
+
+	/* Check if being used in AC97 mode */
+	sprop = of_get_property(np, "fsl,mode", NULL);
+	if (sprop && !strcmp(sprop, "ac97-slave")) {
+		ssi->dai_fmt = FSLSSI_AC97_DAIFMT;
+
+		ret = of_property_read_u32(np, "cell-index", &ssi->card_idx);
+		if (ret) {
+			dev_err(dev, "failed to get SSI index property\n");
+			return -EINVAL;
+		}
+		strcpy(ssi->card_name, "ac97-codec");
+	} else if (!of_property_read_bool(np, "fsl,ssi-asynchronous")) {
+		/*
+		 * In synchronous mode, STCK and STFS ports are used by RX
+		 * as well. So the software should limit the sample rates,
+		 * sample bits and channels to be symmetric.
+		 *
+		 * This is exclusive with FSLSSI_AC97_FORMATS as AC97 runs
+		 * in the SSI synchronous mode however it does not have to
+		 * limit symmetric sample rates and sample bits.
+		 */
+		ssi->synchronous = true;
+	}
+
+	/* Select DMA or FIQ */
+	ssi->use_dma = !of_property_read_bool(np, "fsl,fiq-stream-filter");
+
+	/* Fetch FIFO depth; Set to 8 for older DT without this property */
+	iprop = of_get_property(np, "fsl,fifo-depth", NULL);
+	if (iprop)
+		ssi->fifo_depth = be32_to_cpup(iprop);
+	else
+		ssi->fifo_depth = 8;
+
+	/* Use dual FIFO mode depending on the support from SDMA script */
+	ret = of_property_read_u32_array(np, "dmas", dmas, 4);
+	if (ssi->use_dma && !ret && dmas[2] == IMX_DMATYPE_SSI_DUAL)
+		ssi->use_dual_fifo = true;
+
+	if (ssi->use_dma && !ret && dmas[2] == IMX_DMATYPE_MULTI_SAI)
+		ssi->use_dyna_fifo = true;
+	/*
+	 * Backward compatible for older bindings by manually triggering the
+	 * machine driver's probe(). Use /compatible property, including the
+	 * address of CPU DAI driver structure, as the name of machine driver
+	 *
+	 * If card_name is set by AC97 earlier, bypass here since it uses a
+	 * different name to register the device.
+	 */
+	if (!ssi->card_name[0] && of_get_property(np, "codec-handle", NULL)) {
+		struct device_node *root = of_find_node_by_path("/");
+
+		sprop = of_get_property(root, "compatible", NULL);
+		of_node_put(root);
+		/* Strip "fsl," in the compatible name if applicable */
+		p = strrchr(sprop, ',');
+		if (p)
+			sprop = p + 1;
+		snprintf(ssi->card_name, sizeof(ssi->card_name),
+			 "snd-soc-%s", sprop);
+		make_lowercase(ssi->card_name);
+		ssi->card_idx = 0;
+	}
+
+	return 0;
+}
+
+static int fsl_ssi_probe(struct platform_device *pdev)
+{
+	struct regmap_config regconfig = fsl_ssi_regconfig;
+	struct device *dev = &pdev->dev;
+	struct fsl_ssi *ssi;
+	struct resource *res;
+	void __iomem *iomem;
+	int ret = 0;
+
+	ssi = devm_kzalloc(dev, sizeof(*ssi), GFP_KERNEL);
+	if (!ssi)
+		return -ENOMEM;
+
+	ssi->dev = dev;
+	ssi->soc = of_device_get_match_data(&pdev->dev);
+
+	/* Probe from DT */
+	ret = fsl_ssi_probe_from_dt(ssi);
+	if (ret)
+		return ret;
+
+	if (fsl_ssi_is_ac97(ssi)) {
+		memcpy(&ssi->cpu_dai_drv, &fsl_ssi_ac97_dai,
+		       sizeof(fsl_ssi_ac97_dai));
+		fsl_ac97_data = ssi;
+	} else {
+		memcpy(&ssi->cpu_dai_drv, &fsl_ssi_dai_template,
+		       sizeof(fsl_ssi_dai_template));
+	}
+	ssi->cpu_dai_drv.name = dev_name(dev);
+
+	iomem = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
+	if (IS_ERR(iomem))
+		return PTR_ERR(iomem);
+	ssi->ssi_phys = res->start;
+
+	if (ssi->soc->imx21regs) {
+		/* No SACC{ST,EN,DIS} regs in imx21-class SSI */
+		regconfig.max_register = REG_SSI_SRMSK;
+		regconfig.num_reg_defaults_raw =
+			REG_SSI_SRMSK / sizeof(uint32_t) + 1;
+	}
+
+	if (ssi->has_ipg_clk_name)
+		ssi->regs = devm_regmap_init_mmio_clk(dev, "ipg", iomem,
+						      &regconfig);
+	else
+		ssi->regs = devm_regmap_init_mmio(dev, iomem, &regconfig);
+	if (IS_ERR(ssi->regs)) {
+		dev_err(dev, "failed to init register map\n");
+		return PTR_ERR(ssi->regs);
+	}
+
+	ssi->irq = platform_get_irq(pdev, 0);
+	if (ssi->irq < 0)
+		return ssi->irq;
+
+	/* Set software limitations for synchronous mode except AC97 */
+	if (ssi->synchronous && !fsl_ssi_is_ac97(ssi)) {
+		ssi->cpu_dai_drv.symmetric_rate = 1;
+		ssi->cpu_dai_drv.symmetric_channels = 1;
+		ssi->cpu_dai_drv.symmetric_sample_bits = 1;
+	}
+
+	/*
+	 * Configure TX and RX DMA watermarks -- when to send a DMA request
+	 *
+	 * Values should be tested to avoid FIFO under/over run. Set maxburst
+	 * to fifo_watermark to maxiumize DMA transaction to reduce overhead.
+	 */
+	switch (ssi->fifo_depth) {
+	case 15:
+		/*
+		 * Set to 8 as a balanced configuration -- When TX FIFO has 8
+		 * empty slots, send a DMA request to fill these 8 slots. The
+		 * remaining 7 slots should be able to allow DMA to finish the
+		 * transaction before TX FIFO underruns; Same applies to RX.
+		 *
+		 * Tested with cases running at 48kHz @ 16 bits x 16 channels
+		 */
+		ssi->fifo_watermark = 8;
+		ssi->dma_maxburst = 8;
+		break;
+	case 8:
+	default:
+		/* Safely use old watermark configurations for older chips */
+		ssi->fifo_watermark = ssi->fifo_depth - 2;
+		ssi->dma_maxburst = ssi->fifo_depth - 2;
+		break;
+	}
+
+	dev_set_drvdata(dev, ssi);
+
+	if (ssi->soc->imx) {
+		ret = fsl_ssi_imx_probe(pdev, ssi, iomem);
+		if (ret)
+			return ret;
+	}
+
+	if (fsl_ssi_is_ac97(ssi)) {
+		mutex_init(&ssi->ac97_reg_lock);
+		ret = snd_soc_set_ac97_ops_of_reset(&fsl_ssi_ac97_ops, pdev);
+		if (ret) {
+			dev_err(dev, "failed to set AC'97 ops\n");
+			goto error_ac97_ops;
+		}
+	}
+
+	ret = devm_snd_soc_register_component(dev, &fsl_ssi_component,
+					      &ssi->cpu_dai_drv, 1);
+	if (ret) {
+		dev_err(dev, "failed to register DAI: %d\n", ret);
+		goto error_asoc_register;
+	}
+
+	if (ssi->use_dma) {
+		ret = devm_request_irq(dev, ssi->irq, fsl_ssi_isr, 0,
+				       dev_name(dev), ssi);
+		if (ret < 0) {
+			dev_err(dev, "failed to claim irq %u\n", ssi->irq);
+			goto error_asoc_register;
+		}
+	}
+
+	fsl_ssi_debugfs_create(&ssi->dbg_stats, dev);
+
+	/* Initially configures SSI registers */
+	fsl_ssi_hw_init(ssi);
+
+	/* Register a platform device for older bindings or AC97 */
+	if (ssi->card_name[0]) {
+		struct device *parent = dev;
+		/*
+		 * Do not set SSI dev as the parent of AC97 CODEC device since
+		 * it does not have a DT node. Otherwise ASoC core will assume
+		 * CODEC has the same DT node as the SSI, so it may bypass the
+		 * dai_probe() of SSI and then cause NULL DMA data pointers.
+		 */
+		if (fsl_ssi_is_ac97(ssi))
+			parent = NULL;
+
+		ssi->card_pdev = platform_device_register_data(parent,
+				ssi->card_name, ssi->card_idx, NULL, 0);
+		if (IS_ERR(ssi->card_pdev)) {
+			ret = PTR_ERR(ssi->card_pdev);
+			dev_err(dev, "failed to register %s: %d\n",
+				ssi->card_name, ret);
+			goto error_sound_card;
+		}
+	}
+
+	return 0;
+
+error_sound_card:
+	fsl_ssi_debugfs_remove(&ssi->dbg_stats);
+error_asoc_register:
+	if (fsl_ssi_is_ac97(ssi))
+		snd_soc_set_ac97_ops(NULL);
+error_ac97_ops:
+	if (fsl_ssi_is_ac97(ssi))
+		mutex_destroy(&ssi->ac97_reg_lock);
+
+	if (ssi->soc->imx)
+		fsl_ssi_imx_clean(pdev, ssi);
+
+	return ret;
+}
+
+static void fsl_ssi_remove(struct platform_device *pdev)
+{
+	struct fsl_ssi *ssi = dev_get_drvdata(&pdev->dev);
+
+	fsl_ssi_debugfs_remove(&ssi->dbg_stats);
+
+	if (ssi->card_pdev)
+		platform_device_unregister(ssi->card_pdev);
+
+	/* Clean up SSI registers */
+	fsl_ssi_hw_clean(ssi);
+
+	if (ssi->soc->imx)
+		fsl_ssi_imx_clean(pdev, ssi);
+
+	if (fsl_ssi_is_ac97(ssi)) {
+		snd_soc_set_ac97_ops(NULL);
+		mutex_destroy(&ssi->ac97_reg_lock);
+	}
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int fsl_ssi_suspend(struct device *dev)
+{
+	struct fsl_ssi *ssi = dev_get_drvdata(dev);
+	struct regmap *regs = ssi->regs;
+
+	regmap_read(regs, REG_SSI_SFCSR, &ssi->regcache_sfcsr);
+	regmap_read(regs, REG_SSI_SACNT, &ssi->regcache_sacnt);
+
+	regcache_cache_only(regs, true);
+	regcache_mark_dirty(regs);
+
+	return 0;
+}
+
+static int fsl_ssi_resume(struct device *dev)
+{
+	struct fsl_ssi *ssi = dev_get_drvdata(dev);
+	struct regmap *regs = ssi->regs;
+
+	regcache_cache_only(regs, false);
+
+	regmap_update_bits(regs, REG_SSI_SFCSR,
+			   SSI_SFCSR_RFWM1_MASK | SSI_SFCSR_TFWM1_MASK |
+			   SSI_SFCSR_RFWM0_MASK | SSI_SFCSR_TFWM0_MASK,
+			   ssi->regcache_sfcsr);
+	regmap_write(regs, REG_SSI_SACNT, ssi->regcache_sacnt);
+
+	return regcache_sync(regs);
+}
+#endif /* CONFIG_PM_SLEEP */
+
+static const struct dev_pm_ops fsl_ssi_pm = {
+	SET_SYSTEM_SLEEP_PM_OPS(fsl_ssi_suspend, fsl_ssi_resume)
+};
+
+static struct platform_driver fsl_ssi_driver = {
+	.driver = {
+		.name = "fsl-ssi-dai",
+		.of_match_table = fsl_ssi_ids,
+		.pm = &fsl_ssi_pm,
+	},
+	.probe = fsl_ssi_probe,
+	.remove_new = fsl_ssi_remove,
+};
+
+module_platform_driver(fsl_ssi_driver);
+
+MODULE_ALIAS("platform:fsl-ssi-dai");
+MODULE_AUTHOR("Timur Tabi <timur@freescale.com>");
+MODULE_DESCRIPTION("Freescale Synchronous Serial Interface (SSI) ASoC Driver");
+MODULE_LICENSE("GPL v2");