diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/accounting/psi.rst | 188 |
1 files changed, 188 insertions, 0 deletions
diff --git a/Documentation/accounting/psi.rst b/Documentation/accounting/psi.rst new file mode 100644 index 0000000000..d455db3e58 --- /dev/null +++ b/Documentation/accounting/psi.rst @@ -0,0 +1,188 @@ +.. _psi: + +================================ +PSI - Pressure Stall Information +================================ + +:Date: April, 2018 +:Author: Johannes Weiner <hannes@cmpxchg.org> + +When CPU, memory or IO devices are contended, workloads experience +latency spikes, throughput losses, and run the risk of OOM kills. + +Without an accurate measure of such contention, users are forced to +either play it safe and under-utilize their hardware resources, or +roll the dice and frequently suffer the disruptions resulting from +excessive overcommit. + +The psi feature identifies and quantifies the disruptions caused by +such resource crunches and the time impact it has on complex workloads +or even entire systems. + +Having an accurate measure of productivity losses caused by resource +scarcity aids users in sizing workloads to hardware--or provisioning +hardware according to workload demand. + +As psi aggregates this information in realtime, systems can be managed +dynamically using techniques such as load shedding, migrating jobs to +other systems or data centers, or strategically pausing or killing low +priority or restartable batch jobs. + +This allows maximizing hardware utilization without sacrificing +workload health or risking major disruptions such as OOM kills. + +Pressure interface +================== + +Pressure information for each resource is exported through the +respective file in /proc/pressure/ -- cpu, memory, and io. + +The format is as such:: + + some avg10=0.00 avg60=0.00 avg300=0.00 total=0 + full avg10=0.00 avg60=0.00 avg300=0.00 total=0 + +The "some" line indicates the share of time in which at least some +tasks are stalled on a given resource. + +The "full" line indicates the share of time in which all non-idle +tasks are stalled on a given resource simultaneously. In this state +actual CPU cycles are going to waste, and a workload that spends +extended time in this state is considered to be thrashing. This has +severe impact on performance, and it's useful to distinguish this +situation from a state where some tasks are stalled but the CPU is +still doing productive work. As such, time spent in this subset of the +stall state is tracked separately and exported in the "full" averages. + +CPU full is undefined at the system level, but has been reported +since 5.13, so it is set to zero for backward compatibility. + +The ratios (in %) are tracked as recent trends over ten, sixty, and +three hundred second windows, which gives insight into short term events +as well as medium and long term trends. The total absolute stall time +(in us) is tracked and exported as well, to allow detection of latency +spikes which wouldn't necessarily make a dent in the time averages, +or to average trends over custom time frames. + +Monitoring for pressure thresholds +================================== + +Users can register triggers and use poll() to be woken up when resource +pressure exceeds certain thresholds. + +A trigger describes the maximum cumulative stall time over a specific +time window, e.g. 100ms of total stall time within any 500ms window to +generate a wakeup event. + +To register a trigger user has to open psi interface file under +/proc/pressure/ representing the resource to be monitored and write the +desired threshold and time window. The open file descriptor should be +used to wait for trigger events using select(), poll() or epoll(). +The following format is used:: + + <some|full> <stall amount in us> <time window in us> + +For example writing "some 150000 1000000" into /proc/pressure/memory +would add 150ms threshold for partial memory stall measured within +1sec time window. Writing "full 50000 1000000" into /proc/pressure/io +would add 50ms threshold for full io stall measured within 1sec time window. + +Triggers can be set on more than one psi metric and more than one trigger +for the same psi metric can be specified. However for each trigger a separate +file descriptor is required to be able to poll it separately from others, +therefore for each trigger a separate open() syscall should be made even +when opening the same psi interface file. Write operations to a file descriptor +with an already existing psi trigger will fail with EBUSY. + +Monitors activate only when system enters stall state for the monitored +psi metric and deactivates upon exit from the stall state. While system is +in the stall state psi signal growth is monitored at a rate of 10 times per +tracking window. + +The kernel accepts window sizes ranging from 500ms to 10s, therefore min +monitoring update interval is 50ms and max is 1s. Min limit is set to +prevent overly frequent polling. Max limit is chosen as a high enough number +after which monitors are most likely not needed and psi averages can be used +instead. + +Unprivileged users can also create monitors, with the only limitation that the +window size must be a multiple of 2s, in order to prevent excessive resource +usage. + +When activated, psi monitor stays active for at least the duration of one +tracking window to avoid repeated activations/deactivations when system is +bouncing in and out of the stall state. + +Notifications to the userspace are rate-limited to one per tracking window. + +The trigger will de-register when the file descriptor used to define the +trigger is closed. + +Userspace monitor usage example +=============================== + +:: + + #include <errno.h> + #include <fcntl.h> + #include <stdio.h> + #include <poll.h> + #include <string.h> + #include <unistd.h> + + /* + * Monitor memory partial stall with 1s tracking window size + * and 150ms threshold. + */ + int main() { + const char trig[] = "some 150000 1000000"; + struct pollfd fds; + int n; + + fds.fd = open("/proc/pressure/memory", O_RDWR | O_NONBLOCK); + if (fds.fd < 0) { + printf("/proc/pressure/memory open error: %s\n", + strerror(errno)); + return 1; + } + fds.events = POLLPRI; + + if (write(fds.fd, trig, strlen(trig) + 1) < 0) { + printf("/proc/pressure/memory write error: %s\n", + strerror(errno)); + return 1; + } + + printf("waiting for events...\n"); + while (1) { + n = poll(&fds, 1, -1); + if (n < 0) { + printf("poll error: %s\n", strerror(errno)); + return 1; + } + if (fds.revents & POLLERR) { + printf("got POLLERR, event source is gone\n"); + return 0; + } + if (fds.revents & POLLPRI) { + printf("event triggered!\n"); + } else { + printf("unknown event received: 0x%x\n", fds.revents); + return 1; + } + } + + return 0; + } + +Cgroup2 interface +================= + +In a system with a CONFIG_CGROUPS=y kernel and the cgroup2 filesystem +mounted, pressure stall information is also tracked for tasks grouped +into cgroups. Each subdirectory in the cgroupfs mountpoint contains +cpu.pressure, memory.pressure, and io.pressure files; the format is +the same as the /proc/pressure/ files. + +Per-cgroup psi monitors can be specified and used the same way as +system-wide ones. |