diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/admin-guide/cgroup-v2.rst | 48 |
1 files changed, 42 insertions, 6 deletions
diff --git a/Documentation/admin-guide/cgroup-v2.rst b/Documentation/admin-guide/cgroup-v2.rst index 3f85254f3c..17e6e95651 100644 --- a/Documentation/admin-guide/cgroup-v2.rst +++ b/Documentation/admin-guide/cgroup-v2.rst @@ -1093,7 +1093,11 @@ All time durations are in microseconds. A read-write single value file which exists on non-root cgroups. The default is "100". - The weight in the range [1, 10000]. + For non idle groups (cpu.idle = 0), the weight is in the + range [1, 10000]. + + If the cgroup has been configured to be SCHED_IDLE (cpu.idle = 1), + then the weight will show as a 0. cpu.weight.nice A read-write single value file which exists on non-root @@ -1157,6 +1161,16 @@ All time durations are in microseconds. values similar to the sched_setattr(2). This maximum utilization value is used to clamp the task specific maximum utilization clamp. + cpu.idle + A read-write single value file which exists on non-root cgroups. + The default is 0. + + This is the cgroup analog of the per-task SCHED_IDLE sched policy. + Setting this value to a 1 will make the scheduling policy of the + cgroup SCHED_IDLE. The threads inside the cgroup will retain their + own relative priorities, but the cgroup itself will be treated as + very low priority relative to its peers. + Memory @@ -1679,6 +1693,21 @@ PAGE_SIZE multiple when read back. limit, it will refuse to take any more stores before existing entries fault back in or are written out to disk. + memory.zswap.writeback + A read-write single value file. The default value is "1". The + initial value of the root cgroup is 1, and when a new cgroup is + created, it inherits the current value of its parent. + + When this is set to 0, all swapping attempts to swapping devices + are disabled. This included both zswap writebacks, and swapping due + to zswap store failures. If the zswap store failures are recurring + (for e.g if the pages are incompressible), users can observe + reclaim inefficiency after disabling writeback (because the same + pages might be rejected again and again). + + Note that this is subtly different from setting memory.swap.max to + 0, as it still allows for pages to be written to the zswap pool. + memory.pressure A read-only nested-keyed file. @@ -2316,6 +2345,13 @@ Cpuset Interface Files treated to have an implicit value of "cpuset.cpus" in the formation of local partition. + cpuset.cpus.isolated + A read-only and root cgroup only multiple values file. + + This file shows the set of all isolated CPUs used in existing + isolated partitions. It will be empty if no isolated partition + is created. + cpuset.cpus.partition A read-write single value file which exists on non-root cpuset-enabled cgroups. This flag is owned by the parent cgroup @@ -2358,11 +2394,11 @@ Cpuset Interface Files partition or scheduling domain. The set of exclusive CPUs is determined by the value of its "cpuset.cpus.exclusive.effective". - When set to "isolated", the CPUs in that partition will - be in an isolated state without any load balancing from the - scheduler. Tasks placed in such a partition with multiple - CPUs should be carefully distributed and bound to each of the - individual CPUs for optimal performance. + When set to "isolated", the CPUs in that partition will be in + an isolated state without any load balancing from the scheduler + and excluded from the unbound workqueues. Tasks placed in such + a partition with multiple CPUs should be carefully distributed + and bound to each of the individual CPUs for optimal performance. A partition root ("root" or "isolated") can be in one of the two possible states - valid or invalid. An invalid partition |