summaryrefslogtreecommitdiffstats
path: root/Documentation/admin-guide/cgroup-v2.rst
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/admin-guide/cgroup-v2.rst')
-rw-r--r--Documentation/admin-guide/cgroup-v2.rst48
1 files changed, 42 insertions, 6 deletions
diff --git a/Documentation/admin-guide/cgroup-v2.rst b/Documentation/admin-guide/cgroup-v2.rst
index 3f85254f3c..17e6e95651 100644
--- a/Documentation/admin-guide/cgroup-v2.rst
+++ b/Documentation/admin-guide/cgroup-v2.rst
@@ -1093,7 +1093,11 @@ All time durations are in microseconds.
A read-write single value file which exists on non-root
cgroups. The default is "100".
- The weight in the range [1, 10000].
+ For non idle groups (cpu.idle = 0), the weight is in the
+ range [1, 10000].
+
+ If the cgroup has been configured to be SCHED_IDLE (cpu.idle = 1),
+ then the weight will show as a 0.
cpu.weight.nice
A read-write single value file which exists on non-root
@@ -1157,6 +1161,16 @@ All time durations are in microseconds.
values similar to the sched_setattr(2). This maximum utilization
value is used to clamp the task specific maximum utilization clamp.
+ cpu.idle
+ A read-write single value file which exists on non-root cgroups.
+ The default is 0.
+
+ This is the cgroup analog of the per-task SCHED_IDLE sched policy.
+ Setting this value to a 1 will make the scheduling policy of the
+ cgroup SCHED_IDLE. The threads inside the cgroup will retain their
+ own relative priorities, but the cgroup itself will be treated as
+ very low priority relative to its peers.
+
Memory
@@ -1679,6 +1693,21 @@ PAGE_SIZE multiple when read back.
limit, it will refuse to take any more stores before existing
entries fault back in or are written out to disk.
+ memory.zswap.writeback
+ A read-write single value file. The default value is "1". The
+ initial value of the root cgroup is 1, and when a new cgroup is
+ created, it inherits the current value of its parent.
+
+ When this is set to 0, all swapping attempts to swapping devices
+ are disabled. This included both zswap writebacks, and swapping due
+ to zswap store failures. If the zswap store failures are recurring
+ (for e.g if the pages are incompressible), users can observe
+ reclaim inefficiency after disabling writeback (because the same
+ pages might be rejected again and again).
+
+ Note that this is subtly different from setting memory.swap.max to
+ 0, as it still allows for pages to be written to the zswap pool.
+
memory.pressure
A read-only nested-keyed file.
@@ -2316,6 +2345,13 @@ Cpuset Interface Files
treated to have an implicit value of "cpuset.cpus" in the
formation of local partition.
+ cpuset.cpus.isolated
+ A read-only and root cgroup only multiple values file.
+
+ This file shows the set of all isolated CPUs used in existing
+ isolated partitions. It will be empty if no isolated partition
+ is created.
+
cpuset.cpus.partition
A read-write single value file which exists on non-root
cpuset-enabled cgroups. This flag is owned by the parent cgroup
@@ -2358,11 +2394,11 @@ Cpuset Interface Files
partition or scheduling domain. The set of exclusive CPUs is
determined by the value of its "cpuset.cpus.exclusive.effective".
- When set to "isolated", the CPUs in that partition will
- be in an isolated state without any load balancing from the
- scheduler. Tasks placed in such a partition with multiple
- CPUs should be carefully distributed and bound to each of the
- individual CPUs for optimal performance.
+ When set to "isolated", the CPUs in that partition will be in
+ an isolated state without any load balancing from the scheduler
+ and excluded from the unbound workqueues. Tasks placed in such
+ a partition with multiple CPUs should be carefully distributed
+ and bound to each of the individual CPUs for optimal performance.
A partition root ("root" or "isolated") can be in one of the
two possible states - valid or invalid. An invalid partition