diff options
Diffstat (limited to 'Documentation/admin-guide/kdump')
| -rw-r--r-- | Documentation/admin-guide/kdump/kdump.rst | 37 | ||||
| -rw-r--r-- | Documentation/admin-guide/kdump/vmcoreinfo.rst | 30 |
2 files changed, 3 insertions, 64 deletions
diff --git a/Documentation/admin-guide/kdump/kdump.rst b/Documentation/admin-guide/kdump/kdump.rst index a748e7eb44..5762e7477a 100644 --- a/Documentation/admin-guide/kdump/kdump.rst +++ b/Documentation/admin-guide/kdump/kdump.rst @@ -17,7 +17,7 @@ You can use common commands, such as cp, scp or makedumpfile to copy the memory image to a dump file on the local disk, or across the network to a remote system. -Kdump and kexec are currently supported on the x86, x86_64, ppc64, ia64, +Kdump and kexec are currently supported on the x86, x86_64, ppc64, s390x, arm and arm64 architectures. When the system kernel boots, it reserves a small section of memory for @@ -113,7 +113,7 @@ There are two possible methods of using Kdump. 2) Or use the system kernel binary itself as dump-capture kernel and there is no need to build a separate dump-capture kernel. This is possible only with the architectures which support a relocatable kernel. As - of today, i386, x86_64, ppc64, ia64, arm and arm64 architectures support + of today, i386, x86_64, ppc64, arm and arm64 architectures support relocatable kernel. Building a relocatable kernel is advantageous from the point of view that @@ -236,24 +236,6 @@ Dump-capture kernel config options (Arch Dependent, ppc64) Make and install the kernel and its modules. -Dump-capture kernel config options (Arch Dependent, ia64) ----------------------------------------------------------- - -- No specific options are required to create a dump-capture kernel - for ia64, other than those specified in the arch independent section - above. This means that it is possible to use the system kernel - as a dump-capture kernel if desired. - - The crashkernel region can be automatically placed by the system - kernel at runtime. This is done by specifying the base address as 0, - or omitting it all together:: - - crashkernel=256M@0 - - or:: - - crashkernel=256M - Dump-capture kernel config options (Arch Dependent, arm) ---------------------------------------------------------- @@ -348,11 +330,6 @@ Boot into System Kernel On ppc64, use "crashkernel=128M@32M". - On ia64, 256M@256M is a generous value that typically works. - The region may be automatically placed on ia64, see the - dump-capture kernel config option notes above. - If use sparse memory, the size should be rounded to GRANULE boundaries. - On s390x, typically use "crashkernel=xxM". The value of xx is dependent on the memory consumption of the kdump system. In general this is not dependent on the memory size of the production system. @@ -383,10 +360,6 @@ For ppc64: - Use vmlinux -For ia64: - - - Use vmlinux or vmlinuz.gz - For s390x: - Use image or bzImage @@ -428,14 +401,10 @@ to load dump-capture kernel:: --initrd=<initrd-for-dump-capture-kernel> \ --append="root=<root-dev> <arch-specific-options>" -Please note, that --args-linux does not need to be specified for ia64. -It is planned to make this a no-op on that architecture, but for now -it should be omitted - Following are the arch specific command line options to be used while loading dump-capture kernel. -For i386, x86_64 and ia64: +For i386 and x86_64: "1 irqpoll nr_cpus=1 reset_devices" diff --git a/Documentation/admin-guide/kdump/vmcoreinfo.rst b/Documentation/admin-guide/kdump/vmcoreinfo.rst index 599e8d3bcb..78e4d2e7ba 100644 --- a/Documentation/admin-guide/kdump/vmcoreinfo.rst +++ b/Documentation/admin-guide/kdump/vmcoreinfo.rst @@ -413,36 +413,6 @@ of a higher page table lookup overhead, and also consumes more page table space per process. Used to check whether PAE was enabled in the crash kernel when converting virtual addresses to physical addresses. -ia64 -==== - -pgdat_list|(pgdat_list, MAX_NUMNODES) -------------------------------------- - -pg_data_t array storing all NUMA nodes information. MAX_NUMNODES -indicates the number of the nodes. - -node_memblk|(node_memblk, NR_NODE_MEMBLKS) ------------------------------------------- - -List of node memory chunks. Filled when parsing the SRAT table to obtain -information about memory nodes. NR_NODE_MEMBLKS indicates the number of -node memory chunks. - -These values are used to compute the number of nodes the crashed kernel used. - -node_memblk_s|(node_memblk_s, start_paddr)|(node_memblk_s, size) ----------------------------------------------------------------- - -The size of a struct node_memblk_s and the offsets of the -node_memblk_s's members. Used to compute the number of nodes. - -PGTABLE_3|PGTABLE_4 -------------------- - -User-space tools need to know whether the crash kernel was in 3-level or -4-level paging mode. Used to distinguish the page table. - ARM64 ===== |