diff options
Diffstat (limited to 'Documentation/devicetree/bindings/dma/ti/k3-udma.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/dma/ti/k3-udma.yaml | 179 |
1 files changed, 179 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/dma/ti/k3-udma.yaml b/Documentation/devicetree/bindings/dma/ti/k3-udma.yaml new file mode 100644 index 0000000000..22f6c5e2f7 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/ti/k3-udma.yaml @@ -0,0 +1,179 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2019 Texas Instruments Incorporated +# Author: Peter Ujfalusi <peter.ujfalusi@ti.com> +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/dma/ti/k3-udma.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments K3 NAVSS Unified DMA + +maintainers: + - Peter Ujfalusi <peter.ujfalusi@gmail.com> + +description: | + The UDMA-P is intended to perform similar (but significantly upgraded) + functions as the packet-oriented DMA used on previous SoC devices. The UDMA-P + module supports the transmission and reception of various packet types. + The UDMA-P architecture facilitates the segmentation and reassembly of SoC DMA + data structure compliant packets to/from smaller data blocks that are natively + compatible with the specific requirements of each connected peripheral. + Multiple Tx and Rx channels are provided within the DMA which allow multiple + segmentation or reassembly operations to be ongoing. The DMA controller + maintains state information for each of the channels which allows packet + segmentation and reassembly operations to be time division multiplexed between + channels in order to share the underlying DMA hardware. An external DMA + scheduler is used to control the ordering and rate at which this multiplexing + occurs for Transmit operations. The ordering and rate of Receive operations + is indirectly controlled by the order in which blocks are pushed into the DMA + on the Rx PSI-L interface. + + The UDMA-P also supports acting as both a UTC and UDMA-C for its internal + channels. Channels in the UDMA-P can be configured to be either Packet-Based + or Third-Party channels on a channel by channel basis. + + All transfers within NAVSS is done between PSI-L source and destination + threads. + The peripherals serviced by UDMA can be PSI-L native (sa2ul, cpsw, etc) or + legacy, non PSI-L native peripherals. In the later case a special, small PDMA + is tasked to act as a bridge between the PSI-L fabric and the legacy + peripheral. + + PDMAs can be configured via UDMAP peer registers to match with the + configuration of the legacy peripheral. + +allOf: + - $ref: ../dma-controller.yaml# + - $ref: /schemas/arm/keystone/ti,k3-sci-common.yaml# + +properties: + "#dma-cells": + minimum: 1 + maximum: 2 + description: | + The cell is the PSI-L thread ID of the remote (to UDMAP) end. + Valid ranges for thread ID depends on the data movement direction: + for source thread IDs (rx): 0 - 0x7fff + for destination thread IDs (tx): 0x8000 - 0xffff + + Please refer to the device documentation for the PSI-L thread map and also + the PSI-L peripheral chapter for the correct thread ID. + + When #dma-cells is 2, the second parameter is the channel ATYPE. + + compatible: + enum: + - ti,am654-navss-main-udmap + - ti,am654-navss-mcu-udmap + - ti,j721e-navss-main-udmap + - ti,j721e-navss-mcu-udmap + + reg: + maxItems: 3 + + reg-names: + items: + - const: gcfg + - const: rchanrt + - const: tchanrt + + msi-parent: true + + ti,ringacc: + description: phandle to the ring accelerator node + $ref: /schemas/types.yaml#/definitions/phandle + + ti,sci-rm-range-tchan: + description: | + Array of UDMA tchan resource subtypes for resource allocation for this + host + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + # Should be enough + maxItems: 255 + + ti,sci-rm-range-rchan: + description: | + Array of UDMA rchan resource subtypes for resource allocation for this + host + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + # Should be enough + maxItems: 255 + + ti,sci-rm-range-rflow: + description: | + Array of UDMA rflow resource subtypes for resource allocation for this + host + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + # Should be enough + maxItems: 255 + +required: + - compatible + - "#dma-cells" + - reg + - reg-names + - msi-parent + - ti,sci + - ti,sci-dev-id + - ti,ringacc + - ti,sci-rm-range-tchan + - ti,sci-rm-range-rchan + - ti,sci-rm-range-rflow + +if: + properties: + "#dma-cells": + const: 2 +then: + properties: + ti,udma-atype: + description: ATYPE value which should be used by non slave channels + $ref: /schemas/types.yaml#/definitions/uint32 + + required: + - ti,udma-atype + +unevaluatedProperties: false + +examples: + - |+ + cbass_main { + #address-cells = <2>; + #size-cells = <2>; + + cbass_main_navss: navss@30800000 { + compatible = "simple-mfd"; + #address-cells = <2>; + #size-cells = <2>; + dma-coherent; + dma-ranges; + ranges = <0x0 0x30800000 0x0 0x30800000 0x0 0x05000000>; + + ti,sci-dev-id = <118>; + + main_udmap: dma-controller@31150000 { + compatible = "ti,am654-navss-main-udmap"; + reg = <0x0 0x31150000 0x0 0x100>, + <0x0 0x34000000 0x0 0x100000>, + <0x0 0x35000000 0x0 0x100000>; + reg-names = "gcfg", "rchanrt", "tchanrt"; + #dma-cells = <1>; + + ti,ringacc = <&ringacc>; + + msi-parent = <&inta_main_udmass>; + + ti,sci = <&dmsc>; + ti,sci-dev-id = <188>; + + ti,sci-rm-range-tchan = <0x1>, /* TX_HCHAN */ + <0x2>; /* TX_CHAN */ + ti,sci-rm-range-rchan = <0x4>, /* RX_HCHAN */ + <0x5>; /* RX_CHAN */ + ti,sci-rm-range-rflow = <0x6>; /* GP RFLOW */ + }; + }; + }; |