diff options
Diffstat (limited to 'Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs7211.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs7211.yaml | 769 |
1 files changed, 769 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs7211.yaml b/Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs7211.yaml new file mode 100644 index 0000000000..8cf371b99f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/azoteq,iqs7211.yaml @@ -0,0 +1,769 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/azoteq,iqs7211.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Azoteq IQS7210A/7211A/E Trackpad/Touchscreen Controller + +maintainers: + - Jeff LaBundy <jeff@labundy.com> + +description: | + The Azoteq IQS7210A, IQS7211A and IQS7211E trackpad and touchscreen control- + lers employ projected-capacitance sensing and can track two contacts. + + Link to datasheets: https://www.azoteq.com/ + +properties: + compatible: + enum: + - azoteq,iqs7210a + - azoteq,iqs7211a + - azoteq,iqs7211e + + reg: + maxItems: 1 + + irq-gpios: + maxItems: 1 + description: + Specifies the GPIO connected to the device's active-low RDY output. The + pin doubles as the IQS7211E's active-low MCLR input, in which case this + GPIO must be configured as open-drain. + + reset-gpios: + maxItems: 1 + description: + Specifies the GPIO connected to the device's active-low MCLR input. The + device is temporarily held in hardware reset prior to initialization if + this property is present. + + azoteq,forced-comms: + type: boolean + description: + Enables forced communication; to be used with host adapters that cannot + tolerate clock stretching. + + azoteq,forced-comms-default: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: + Indicates if the device's OTP memory enables (1) or disables (0) forced + communication by default. Specifying this property can expedite startup + time if the default value is known. + + If this property is not specified, communication is not initiated until + the device asserts its RDY pin shortly after exiting hardware reset. At + that point, forced communication is either enabled or disabled based on + the presence or absence of the 'azoteq,forced-comms' property. + + azoteq,rate-active-ms: + minimum: 0 + maximum: 65535 + description: Specifies the report rate (in ms) during active mode. + + azoteq,rate-touch-ms: + minimum: 0 + maximum: 65535 + description: Specifies the report rate (in ms) during idle-touch mode. + + azoteq,rate-idle-ms: + minimum: 0 + maximum: 65535 + description: Specifies the report rate (in ms) during idle mode. + + azoteq,rate-lp1-ms: + minimum: 0 + maximum: 65535 + description: Specifies the report rate (in ms) during low-power mode 1. + + azoteq,rate-lp2-ms: + minimum: 0 + maximum: 65535 + description: Specifies the report rate (in ms) during low-power mode 2. + + azoteq,timeout-active-ms: + multipleOf: 1000 + minimum: 0 + maximum: 65535000 + description: + Specifies the length of time (in ms) to wait for an event before moving + from active mode to idle or idle-touch modes. + + azoteq,timeout-touch-ms: + multipleOf: 1000 + minimum: 0 + maximum: 65535000 + description: + Specifies the length of time (in ms) to wait for an event before moving + from idle-touch mode to idle mode. + + azoteq,timeout-idle-ms: + multipleOf: 1000 + minimum: 0 + maximum: 65535000 + description: + Specifies the length of time (in ms) to wait for an event before moving + from idle mode to low-power mode 1. + + azoteq,timeout-lp1-ms: + multipleOf: 1000 + minimum: 0 + maximum: 65535000 + description: + Specifies the length of time (in ms) to wait for an event before moving + from low-power mode 1 to low-power mode 2. + + azoteq,timeout-lp2-ms: + multipleOf: 1000 + minimum: 0 + maximum: 60000 + description: + Specifies the rate (in ms) at which the trackpad reference values + are updated during low-power modes 1 and 2. + + azoteq,timeout-ati-ms: + multipleOf: 1000 + minimum: 0 + maximum: 60000 + description: + Specifies the delay (in ms) before the automatic tuning implementation + (ATI) is retried in the event it fails to complete. + + azoteq,timeout-comms-ms: + minimum: 0 + maximum: 65535 + description: + Specifies the delay (in ms) before a communication window is closed. + + azoteq,timeout-press-ms: + multipleOf: 1000 + minimum: 0 + maximum: 60000 + description: + Specifies the length of time (in ms) to wait before automatically + releasing a press event. Specify zero to allow the press state to + persist indefinitely. + + azoteq,fosc-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + Specifies the device's core clock frequency as follows: + 0: 14 MHz + 1: 18 MHz + + azoteq,fosc-trim: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Specifies the device's core clock frequency trim. + + azoteq,num-contacts: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 2 + default: 0 + description: Specifies the number of contacts reported by the device. + + azoteq,contact-split: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the contact (finger) split factor. + + azoteq,trim-x: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the horizontal trim width. + + azoteq,trim-y: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the vertical trim height. + + trackpad: + type: object + description: Represents all channels associated with the trackpad. + + properties: + azoteq,rx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + description: + Specifies the order of the CRx pin(s) associated with the trackpad. + + azoteq,tx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 12 + items: + minimum: 0 + maximum: 11 + description: + Specifies the order of the CTx pin(s) associated with the trackpad. + + azoteq,channel-select: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 36 + items: + minimum: 0 + maximum: 255 + description: | + Specifies the channels mapped to each cycle in the following order: + Cycle 0, slot 0 + Cycle 0, slot 1 + Cycle 1, slot 0 + Cycle 1, slot 1 + ...and so on. Specify 255 to disable a given slot. + + azoteq,ati-frac-div-fine: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the trackpad's ATI fine fractional divider. + + azoteq,ati-frac-mult-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Specifies the trackpad's ATI coarse fractional multiplier. + + azoteq,ati-frac-div-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the trackpad's ATI coarse fractional divider. + + azoteq,ati-comp-div: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the trackpad's ATI compensation divider. + + azoteq,ati-target: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: Specifies the trackpad's ATI target. + + azoteq,touch-enter: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the trackpad's touch entrance factor. + + azoteq,touch-exit: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the trackpad's touch exit factor. + + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the trackpad's stationary touch threshold. + + azoteq,conv-period: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the trackpad's conversion period. + + azoteq,conv-frac: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the trackpad's conversion frequency fraction. + + patternProperties: + "^event-(tap(-double|-triple)?|hold|palm|swipe-(x|y)-(pos|neg)(-hold)?)$": + type: object + $ref: ../input.yaml# + description: + Represents a gesture event reported by the trackpad. In the case of + axial gestures, the duration or distance specified in one direction + applies to both directions along the same axis. + + properties: + linux,code: true + + azoteq,gesture-max-ms: + minimum: 0 + maximum: 65535 + description: Specifies the maximum duration of tap/swipe gestures. + + azoteq,gesture-mid-ms: + minimum: 0 + maximum: 65535 + description: + Specifies the maximum duration between subsequent tap gestures + (IQS7211E only). + + azoteq,gesture-min-ms: + minimum: 0 + maximum: 65535 + description: Specifies the minimum duration of hold gestures. + + azoteq,gesture-dist: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: + Specifies the minimum (swipe) or maximum (tap and hold) distance + a finger may travel to be considered a gesture. + + azoteq,gesture-dist-rep: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: + Specifies the minimum distance a finger must travel to elicit a + repeated swipe gesture (IQS7211E only). + + azoteq,gesture-angle: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 75 + description: + Specifies the maximum angle (in degrees) a finger may travel to + be considered a swipe gesture. + + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 42 + description: Specifies the palm gesture threshold (IQS7211E only). + + additionalProperties: false + + dependencies: + azoteq,rx-enable: ["azoteq,tx-enable"] + azoteq,tx-enable: ["azoteq,rx-enable"] + azoteq,channel-select: ["azoteq,rx-enable"] + + additionalProperties: false + + alp: + type: object + $ref: ../input.yaml# + description: Represents the alternate low-power channel (ALP). + + properties: + azoteq,rx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + description: + Specifies the CRx pin(s) associated with the ALP in no particular + order. + + azoteq,tx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 12 + items: + minimum: 0 + maximum: 11 + description: + Specifies the CTx pin(s) associated with the ALP in no particular + order. + + azoteq,ati-frac-div-fine: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the ALP's ATI fine fractional divider. + + azoteq,ati-frac-mult-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Specifies the ALP's ATI coarse fractional multiplier. + + azoteq,ati-frac-div-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the ALP's ATI coarse fractional divider. + + azoteq,ati-comp-div: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the ALP's ATI compensation divider. + + azoteq,ati-target: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: Specifies the ALP's ATI target. + + azoteq,ati-base: + $ref: /schemas/types.yaml#/definitions/uint32 + multipleOf: 8 + minimum: 0 + maximum: 255 + description: Specifies the ALP's ATI base. + + azoteq,ati-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + Specifies the ALP's ATI mode as follows: + 0: Partial + 1: Full + + azoteq,sense-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + Specifies the ALP's sensing mode as follows: + 0: Self capacitive + 1: Mutual capacitive + + azoteq,debounce-enter: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the ALP's debounce entrance factor. + + azoteq,debounce-exit: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the ALP's debounce exit factor. + + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: Specifies the ALP's proximity or touch threshold. + + azoteq,conv-period: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the ALP's conversion period. + + azoteq,conv-frac: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the ALP's conversion frequency fraction. + + linux,code: true + + additionalProperties: false + + button: + type: object + description: Represents the inductive or capacitive button. + + properties: + azoteq,ati-frac-div-fine: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the button's ATI fine fractional divider. + + azoteq,ati-frac-mult-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Specifies the button's ATI coarse fractional multiplier. + + azoteq,ati-frac-div-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the button's ATI coarse fractional divider. + + azoteq,ati-comp-div: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the button's ATI compensation divider. + + azoteq,ati-target: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: Specifies the button's ATI target. + + azoteq,ati-base: + $ref: /schemas/types.yaml#/definitions/uint32 + multipleOf: 8 + minimum: 0 + maximum: 255 + description: Specifies the button's ATI base. + + azoteq,ati-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + Specifies the button's ATI mode as follows: + 0: Partial + 1: Full + + azoteq,sense-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + description: | + Specifies the button's sensing mode as follows: + 0: Self capacitive + 1: Mutual capacitive + 2: Inductive + + azoteq,touch-enter: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the button's touch entrance factor. + + azoteq,touch-exit: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the button's touch exit factor. + + azoteq,debounce-enter: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the button's debounce entrance factor. + + azoteq,debounce-exit: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the button's debounce exit factor. + + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: Specifies the button's proximity threshold. + + azoteq,conv-period: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the button's conversion period. + + azoteq,conv-frac: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the button's conversion frequency fraction. + + patternProperties: + "^event-(prox|touch)$": + type: object + $ref: ../input.yaml# + description: + Represents a proximity or touch event reported by the button. + + properties: + linux,code: true + + additionalProperties: false + + additionalProperties: false + + wakeup-source: true + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + +dependencies: + touchscreen-size-x: ["azoteq,num-contacts"] + touchscreen-size-y: ["azoteq,num-contacts"] + touchscreen-inverted-x: ["azoteq,num-contacts"] + touchscreen-inverted-y: ["azoteq,num-contacts"] + touchscreen-swapped-x-y: ["azoteq,num-contacts"] + +required: + - compatible + - reg + - irq-gpios + +additionalProperties: false + +allOf: + - $ref: touchscreen.yaml# + + - if: + properties: + compatible: + contains: + const: azoteq,iqs7210a + + then: + properties: + alp: + properties: + azoteq,rx-enable: + maxItems: 4 + items: + minimum: 4 + + else: + properties: + azoteq,timeout-press-ms: false + + alp: + properties: + azoteq,ati-mode: false + + button: false + + - if: + properties: + compatible: + contains: + const: azoteq,iqs7211e + + then: + properties: + reset-gpios: false + + trackpad: + properties: + azoteq,tx-enable: + maxItems: 13 + items: + maximum: 12 + + alp: + properties: + azoteq,tx-enable: + maxItems: 13 + items: + maximum: 12 + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/input/input.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touch@56 { + compatible = "azoteq,iqs7210a"; + reg = <0x56>; + irq-gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio 17 (GPIO_ACTIVE_LOW | + GPIO_PUSH_PULL)>; + azoteq,num-contacts = <2>; + + trackpad { + azoteq,rx-enable = <6>, <5>, <4>, <3>, <2>; + azoteq,tx-enable = <1>, <7>, <8>, <9>, <10>; + }; + + button { + azoteq,sense-mode = <2>; + azoteq,touch-enter = <40>; + azoteq,touch-exit = <36>; + + event-touch { + linux,code = <KEY_HOME>; + }; + }; + + alp { + azoteq,sense-mode = <1>; + linux,code = <KEY_POWER>; + }; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/input/input.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touch@56 { + compatible = "azoteq,iqs7211e"; + reg = <0x56>; + irq-gpios = <&gpio 4 (GPIO_ACTIVE_LOW | + GPIO_OPEN_DRAIN)>; + + trackpad { + event-tap { + linux,code = <KEY_PLAYPAUSE>; + }; + + event-tap-double { + linux,code = <KEY_SHUFFLE>; + }; + + event-tap-triple { + linux,code = <KEY_AGAIN>; + }; + + event-hold { + linux,code = <KEY_STOP>; + }; + + event-palm { + linux,code = <KEY_EXIT>; + }; + + event-swipe-x-pos { + linux,code = <KEY_REWIND>; + }; + + event-swipe-x-pos-hold { + linux,code = <KEY_PREVIOUS>; + }; + + event-swipe-x-neg { + linux,code = <KEY_FASTFORWARD>; + }; + + event-swipe-x-neg-hold { + linux,code = <KEY_NEXT>; + }; + + event-swipe-y-pos { + linux,code = <KEY_VOLUMEUP>; + }; + + event-swipe-y-pos-hold { + linux,code = <KEY_MUTE>; + }; + + event-swipe-y-neg { + linux,code = <KEY_VOLUMEDOWN>; + }; + + event-swipe-y-neg-hold { + linux,code = <KEY_MUTE>; + }; + }; + }; + }; + +... |