summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt')
-rw-r--r--Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt88
1 files changed, 88 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
new file mode 100644
index 0000000000..880d4d70c9
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
@@ -0,0 +1,88 @@
+STMicroelectronics STi c8sectpfe binding
+============================================
+
+This document describes the c8sectpfe device bindings that is used to get transport
+stream data into the SoC on the TS pins, and into DDR for further processing.
+
+It is typically used in conjunction with one or more demodulator and tuner devices
+which converts from the RF to digital domain. Demodulators and tuners are usually
+located on an external DVB frontend card connected to SoC TS input pins.
+
+Currently 7 TS input (tsin) channels are supported on the stih407 family SoC.
+
+Required properties (controller (parent) node):
+- compatible : Should be "stih407-c8sectpfe"
+
+- reg : Address and length of register sets for each device in
+ "reg-names"
+
+- reg-names : The names of the register addresses corresponding to the
+ registers filled in "reg":
+ - c8sectpfe: c8sectpfe registers
+ - c8sectpfe-ram: c8sectpfe internal sram
+
+- clocks : phandle list of c8sectpfe clocks
+- clock-names : should be "c8sectpfe"
+See: Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+- pinctrl-names : a pinctrl state named tsin%d-serial or tsin%d-parallel (where %d is tsin-num)
+ must be defined for each tsin child node.
+- pinctrl-0 : phandle referencing pin configuration for this tsin configuration
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+
+Required properties (tsin (child) node):
+
+- tsin-num : tsin id of the InputBlock (must be between 0 to 6)
+- i2c-bus : phandle to the I2C bus DT node which the demodulators & tuners on this tsin channel are connected.
+- reset-gpios : reset gpio for this tsin channel.
+
+Optional properties (tsin (child) node):
+
+- invert-ts-clk : Bool property to control sense of ts input clock (data stored on falling edge of clk).
+- serial-not-parallel : Bool property to configure input bus width (serial on ts_data<7>).
+- async-not-sync : Bool property to control if data is received in asynchronous mode
+ (all bits/bytes with ts_valid or ts_packet asserted are valid).
+
+- dvb-card : Describes the NIM card connected to this tsin channel.
+
+Example:
+
+/* stih410 SoC b2120 + b2004a + stv0367-pll(NIMB) + stv0367-tda18212 (NIMA) DT example) */
+
+ c8sectpfe@8a20000 {
+ compatible = "st,stih407-c8sectpfe";
+ reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
+ reg-names = "stfe", "stfe-ram";
+ interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, <GIC_SPI 35 IRQ_TYPE_NONE>;
+ interrupt-names = "stfe-error-irq", "stfe-idle-irq";
+ pinctrl-0 = <&pinctrl_tsin0_serial>;
+ pinctrl-1 = <&pinctrl_tsin0_parallel>;
+ pinctrl-2 = <&pinctrl_tsin3_serial>;
+ pinctrl-3 = <&pinctrl_tsin4_serial_alt3>;
+ pinctrl-4 = <&pinctrl_tsin5_serial_alt1>;
+ pinctrl-names = "tsin0-serial",
+ "tsin0-parallel",
+ "tsin3-serial",
+ "tsin4-serial",
+ "tsin5-serial";
+ clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>;
+ clock-names = "c8sectpfe";
+
+ /* tsin0 is TSA on NIMA */
+ tsin0: port@0 {
+ tsin-num = <0>;
+ serial-not-parallel;
+ i2c-bus = <&ssc2>;
+ reset-gpios = <&pio15 4 GPIO_ACTIVE_HIGH>;
+ dvb-card = <STV0367_TDA18212_NIMA_1>;
+ };
+
+ tsin3: port@3 {
+ tsin-num = <3>;
+ serial-not-parallel;
+ i2c-bus = <&ssc3>;
+ reset-gpios = <&pio15 7 GPIO_ACTIVE_HIGH>;
+ dvb-card = <STV0367_TDA18212_NIMB_1>;
+ };
+ };