diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd/ti-lmu.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/ti-lmu.txt | 269 |
1 files changed, 269 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt new file mode 100644 index 0000000000..2296b8f24d --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt @@ -0,0 +1,269 @@ +TI LMU (Lighting Management Unit) device tree bindings + +TI LMU driver supports lighting devices below. + + Name Child nodes + ------ --------------------------------- + LM3631 Backlight and regulator + LM3632 Backlight and regulator + LM3633 Backlight, LED and fault monitor + LM3695 Backlight + LM36274 Backlight and regulator + +Required properties: + - compatible: Should be one of: + "ti,lm3631" + "ti,lm3632" + "ti,lm3633" + "ti,lm3695" + "ti,lm36274" + - reg: I2C slave address. + 0x11 for LM3632 + 0x29 for LM3631 + 0x36 for LM3633 + 0x63 for LM3695 + 0x11 for LM36274 + +Optional properties: + - enable-gpios: A GPIO specifier for hardware enable pin. + - ramp-up-us: Current ramping from one brightness level to + the a higher brightness level. + Range from 2048 us - 117.44 s + - ramp-down-us: Current ramping from one brightness level to + the a lower brightness level. + Range from 2048 us - 117.44 s + - ti,brightness-resolution - This determines whether to use 8 bit brightness + mode or 11 bit brightness mode. If this value is + not set the device is defaulted to the preferred + 8bit brightness mode per 7.3.4.1 of the data + sheet. This setting can either be in the parent + node or as part of the LED child nodes. This + is determined by the part itself if the strings + have a common brightness register or individual + brightness registers. + The values are 255 (8bit) or 2047 (11bit). + +Required node: + - backlight: All LMU devices have backlight child nodes. + For the properties, please refer to [1]. + +Optional nodes: + - fault-monitor: Hardware fault monitoring driver for LM3633 and LM3697. + Required properties: + - compatible: Should be one of: + "ti,lm3633-fault-monitor" + - leds: LED properties for LM3633. Please refer to [2]. + LED properties for LM36274. Please refer to [4]. + - regulators: Regulator properties for LM3631 and LM3632. + Please refer to [3]. + +[1] ../leds/backlight/ti-lmu-backlight.txt +[2] ../leds/leds-lm3633.txt +[3] ../regulator/lm363x-regulator.txt +[4] ../leds/leds-lm36274.txt + +lm3631@29 { + compatible = "ti,lm3631"; + reg = <0x29>; + + regulators { + compatible = "ti,lm363x-regulator"; + + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4500000>; + regulator-max-microvolt = <6350000>; + regulator-always-on; + }; + + vcont { + regulator-name = "lcd_vcont"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + voref { + regulator-name = "lcd_voref"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6000000>; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6000000>; + regulator-boot-on; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6000000>; + regulator-boot-on; + }; + }; + + backlight { + compatible = "ti,lm3631-backlight"; + + lcd_bl { + led-sources = <0 1>; + ramp-up-us = <300000>; + }; + }; +}; + +lm3632@11 { + compatible = "ti,lm3632"; + reg = <0x11>; + + enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; /* PC2 */ + + regulators { + compatible = "ti,lm363x-regulator"; + + enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>, + <&pioC 1 GPIO_ACTIVE_HIGH>; + + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4500000>; + regulator-max-microvolt = <6400000>; + regulator-always-on; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6000000>; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6000000>; + }; + }; + + backlight { + compatible = "ti,lm3632-backlight"; + + pwms = <&pwm0 0 10000 0>; /* pwm number, period, polarity */ + pwm-names = "lmu-backlight"; + + lcd { + led-sources = <0 1>; + pwm-period = <10000>; + }; + }; +}; + +lm3633@36 { + compatible = "ti,lm3633"; + reg = <0x36>; + + enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; + + backlight { + compatible = "ti,lm3633-backlight"; + + main { + label = "main_lcd"; + led-sources = <1 2>; + ramp-up-us = <500000>; + ramp-down-us = <500000>; + }; + + front { + label = "front_lcd"; + led-sources = <0>; + ramp-up-us = <1000000>; + ramp-down-us = <0>; + }; + }; + + leds { + compatible = "ti,lm3633-leds"; + + chan1 { + label = "status"; + led-sources = <1>; + led-max-microamp = <6000>; + }; + + chan345 { + label = "rgb"; + led-sources = <3 4 5>; + led-max-microamp = <10000>; + }; + }; + + fault-monitor { + compatible = "ti,lm3633-fault-monitor"; + }; +}; + +lm3695@63 { + compatible = "ti,lm3695"; + reg = <0x63>; + + enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; + + backlight { + compatible = "ti,lm3695-backlight"; + + lcd { + label = "bl"; + led-sources = <0 1>; + }; + }; +}; + +lm36274@11 { + compatible = "ti,lm36274"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11>; + + enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; + regulators { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm363x-regulator"; + + enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>, + <&pioC 1 GPIO_ACTIVE_HIGH>; + + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <7150000>; + regulator-always-on; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + }; + + backlight { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm36274-backlight"; + + led@0 { + reg = <0>; + led-sources = <0 2>; + label = "white:backlight_cluster"; + linux,default-trigger = "backlight"; + }; + }; +}; |