1 files changed, 60 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
new file mode 100644
index 0000000000..6762d3c4d5
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
@@ -0,0 +1,60 @@
+ST Microelectronics Flexible Static Memory Controller (FSMC)
+NAND Interface
+
+Required properties:
+- compatible : "st,spear600-fsmc-nand", "stericsson,fsmc-nand"
+- reg : Address range of the mtd chip
+- reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd"
+
+Optional properties:
+- bank-width : Width (in bytes) of the device.  If not present, the width
+  defaults to 1 byte
+- nand-skip-bbtscan: Indicates the BBT scanning should be skipped
+- timings: array of 6 bytes for NAND timings. The meanings of these bytes
+  are:
+  byte 0 TCLR  : CLE to RE delay in number of AHB clock cycles, only 4 bits
+                 are valid. Zero means one clockcycle, 15 means 16 clock
+                 cycles.
+  byte 1 TAR   : ALE to RE delay, 4 bits are valid. Same format as TCLR.
+  byte 2 THIZ  : number of HCLK clock cycles during which the data bus is
+                 kept in Hi-Z (tristate) after the start of a write access.
+                 Only valid for write transactions. Zero means zero cycles,
+                 255 means 255 cycles.
+  byte 3 THOLD : number of HCLK clock cycles to hold the address (and data
+                 when writing) after the command deassertation. Zero means
+                 one cycle, 255 means 256 cycles.
+  byte 4 TWAIT : number of HCLK clock cycles to assert the command to the
+                 NAND flash in response to SMWAITn. Zero means 1 cycle,
+                 255 means 256 cycles.
+  byte 5 TSET  : number of HCLK clock cycles to assert the address before the
+                 command is asserted. Zero means one cycle, 255 means 256
+                 cycles.
+- bank: default NAND bank to use (0-3 are valid, 0 is the default).
+- nand-ecc-mode      : see nand-controller.yaml
+- nand-ecc-strength  : see nand-controller.yaml
+- nand-ecc-step-size : see nand-controller.yaml
+
+Can support 1-bit HW ECC (default) or if stronger correction is required,
+software-based BCH.
+
+Example:
+
+	fsmc: flash@d1800000 {
+		compatible = "st,spear600-fsmc-nand";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0xd1800000 0x1000	/* FSMC Register */
+		       0xd2000000 0x0010	/* NAND Base DATA */
+		       0xd2020000 0x0010	/* NAND Base ADDR */
+		       0xd2010000 0x0010>;	/* NAND Base CMD */
+		reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
+
+		bank-width = <1>;
+		nand-skip-bbtscan;
+		timings = /bits/ 8 <0 0 0 2 3 0>;
+		bank = <1>;
+
+		partition@0 {
+			...
+		};
+	};