diff options
Diffstat (limited to '')
70 files changed, 5677 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mtd/allwinner,sun4i-a10-nand.yaml b/Documentation/devicetree/bindings/mtd/allwinner,sun4i-a10-nand.yaml new file mode 100644 index 0000000000..054b6b8bf9 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/allwinner,sun4i-a10-nand.yaml @@ -0,0 +1,111 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/allwinner,sun4i-a10-nand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 NAND Controller + +allOf: + - $ref: nand-controller.yaml + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + compatible: + enum: + - allwinner,sun4i-a10-nand + - allwinner,sun8i-a23-nand-controller + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: ahb + - const: mod + + resets: + maxItems: 1 + + reset-names: + const: ahb + + dmas: + maxItems: 1 + + dma-names: + const: rxtx + +patternProperties: + "^nand@[a-f0-9]$": + type: object + $ref: raw-nand-chip.yaml + properties: + reg: + minimum: 0 + maximum: 7 + + nand-ecc-algo: + const: bch + + nand-ecc-step-size: + enum: [ 512, 1024 ] + + nand-ecc-strength: + maximum: 80 + + allwinner,rb: + description: + Contains the native Ready/Busy IDs. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 2 + items: + minimum: 0 + maximum: 1 + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/sun6i-rtc.h> + #include <dt-bindings/clock/sun8i-a23-a33-ccu.h> + #include <dt-bindings/reset/sun8i-a23-a33-ccu.h> + + nand-controller@1c03000 { + compatible = "allwinner,sun8i-a23-nand-controller"; + reg = <0x01c03000 0x1000>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_NAND>, <&ccu CLK_NAND>; + clock-names = "ahb", "mod"; + resets = <&ccu RST_BUS_NAND>; + reset-names = "ahb"; + dmas = <&dma 5>; + dma-names = "rxtx"; + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins &nand_cs0_pin &nand_rb0_pin>; + #address-cells = <1>; + #size-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.yaml b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.yaml new file mode 100644 index 0000000000..57b6957c84 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/amlogic,meson-nand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic NAND Flash Controller (NFC) for GXBB/GXL/AXG family SoCs + +allOf: + - $ref: nand-controller.yaml + +maintainers: + - liang.yang@amlogic.com + +properties: + compatible: + enum: + - amlogic,meson-gxl-nfc + - amlogic,meson-axg-nfc + + reg: + maxItems: 2 + + reg-names: + items: + - const: nfc + - const: emmc + + interrupts: + maxItems: 1 + + clocks: + minItems: 2 + + clock-names: + items: + - const: core + - const: device + +patternProperties: + "^nand@[0-7]$": + type: object + $ref: raw-nand-chip.yaml + properties: + reg: + minimum: 0 + maximum: 1 + + nand-ecc-mode: + const: hw + + nand-ecc-step-size: + enum: [512, 1024] + + nand-ecc-strength: + enum: [8, 16, 24, 30, 40, 50, 60] + description: | + The ECC configurations that can be supported are as follows. + meson-gxl-nfc 8, 16, 24, 30, 40, 50, 60 + meson-axg-nfc 8 + + nand-rb: + maxItems: 1 + items: + maximum: 0 + + unevaluatedProperties: false + + dependencies: + nand-ecc-strength: [nand-ecc-step-size] + nand-ecc-step-size: [nand-ecc-strength] + + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/axg-clkc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + nand-controller@ffe07800 { + compatible = "amlogic,meson-axg-nfc"; + reg = <0xffe07800 0x100>, <0xffe07000 0x800>; + reg-names = "nfc", "emmc"; + interrupts = <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc CLKID_SD_EMMC_C>, <&clkc CLKID_FCLK_DIV2>; + clock-names = "core", "device"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + nand-rb = <0>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/mtd/arasan,nand-controller.yaml b/Documentation/devicetree/bindings/mtd/arasan,nand-controller.yaml new file mode 100644 index 0000000000..15b63bbb82 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/arasan,nand-controller.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/arasan,nand-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Arasan NAND Flash Controller with ONFI 3.1 support + +allOf: + - $ref: nand-controller.yaml + +maintainers: + - Michal Simek <michal.simek@amd.com> + +properties: + compatible: + items: + - enum: + - xlnx,zynqmp-nand-controller + - const: arasan,nfc-v3p10 + + reg: + maxItems: 1 + + clocks: + items: + - description: Controller clock + - description: NAND bus clock + + clock-names: + items: + - const: controller + - const: bus + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + +unevaluatedProperties: true + +examples: + - | + nfc: nand-controller@ff100000 { + compatible = "xlnx,zynqmp-nand-controller", "arasan,nfc-v3p10"; + reg = <0xff100000 0x1000>; + clock-names = "controller", "bus"; + clocks = <&clk200>, <&clk100>; + interrupt-parent = <&gic>; + interrupts = <0 14 4>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/mtd/arm,pl353-nand-r2p1.yaml b/Documentation/devicetree/bindings/mtd/arm,pl353-nand-r2p1.yaml new file mode 100644 index 0000000000..7bd7c55a9c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/arm,pl353-nand-r2p1.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/arm,pl353-nand-r2p1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: PL353 NAND Controller + +allOf: + - $ref: nand-controller.yaml + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +properties: + compatible: + items: + - const: arm,pl353-nand-r2p1 + + reg: + items: + - items: + - description: CS with regard to the parent ranges property + - description: Offset of the memory region requested by the device + - description: Length of the memory region requested by the device + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + smcc: memory-controller@e000e000 { + compatible = "arm,pl353-smc-r2p1", "arm,primecell"; + reg = <0xe000e000 0x0001000>; + clock-names = "memclk", "apb_pclk"; + clocks = <&clkc 11>, <&clkc 44>; + ranges = <0x0 0x0 0xe1000000 0x1000000 /* Nand CS region */ + 0x1 0x0 0xe2000000 0x2000000 /* SRAM/NOR CS0 region */ + 0x2 0x0 0xe4000000 0x2000000>; /* SRAM/NOR CS1 region */ + #address-cells = <2>; + #size-cells = <1>; + + nfc0: nand-controller@0,0 { + compatible = "arm,pl353-nand-r2p1"; + reg = <0 0 0x1000000>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt b/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt new file mode 100644 index 0000000000..1889a4db5b --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt @@ -0,0 +1,17 @@ +* Atmel Data Flash + +Required properties: +- compatible : "atmel,<model>", "atmel,<series>", "atmel,dataflash". + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + +flash@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at45db321d", "atmel,at45", "atmel,dataflash"; + spi-max-frequency = <25000000>; + reg = <1>; +}; diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt new file mode 100644 index 0000000000..50645828ac --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -0,0 +1,235 @@ +Atmel NAND flash controller bindings + +The NAND flash controller node should be defined under the EBI bus (see +Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt). +One or several NAND devices can be defined under this NAND controller. +The NAND controller might be connected to an ECC engine. + +* NAND controller bindings: + +Required properties: +- compatible: should be one of the following + "atmel,at91rm9200-nand-controller" + "atmel,at91sam9260-nand-controller" + "atmel,at91sam9261-nand-controller" + "atmel,at91sam9g45-nand-controller" + "atmel,sama5d3-nand-controller" + "microchip,sam9x60-nand-controller" +- ranges: empty ranges property to forward EBI ranges definitions. +- #address-cells: should be set to 2. +- #size-cells: should be set to 1. +- atmel,nfc-io: phandle to the NFC IO block. Only required for sama5d3 + controllers. +- atmel,nfc-sram: phandle to the NFC SRAM block. Only required for sama5d3 + controllers. + +Optional properties: +- ecc-engine: phandle to the PMECC block. Only meaningful if the SoC embeds + a PMECC engine. + +* NAND device/chip bindings: + +Required properties: +- reg: describes the CS lines assigned to the NAND device. If the NAND device + exposes multiple CS lines (multi-dies chips), your reg property will + contain X tuples of 3 entries. + 1st entry: the CS line this NAND chip is connected to + 2nd entry: the base offset of the memory region assigned to this + device (always 0) + 3rd entry: the memory region size (always 0x800000) + +Optional properties: +- rb-gpios: the GPIO(s) used to check the Ready/Busy status of the NAND. +- cs-gpios: the GPIO(s) used to control the CS line. +- det-gpios: the GPIO used to detect if a Smartmedia Card is present. +- atmel,rb: an integer identifying the native Ready/Busy pin. Only meaningful + on sama5 SoCs. + +All generic properties are described in the generic yaml files under +Documentation/devicetree/bindings/mtd/. + +* ECC engine (PMECC) bindings: + +Required properties: +- compatible: should be one of the following + "atmel,at91sam9g45-pmecc" + "atmel,sama5d4-pmecc" + "atmel,sama5d2-pmecc" + "microchip,sam9x60-pmecc" +- reg: should contain 2 register ranges. The first one is pointing to the PMECC + block, and the second one to the PMECC_ERRLOC block. + +* SAMA5 NFC I/O bindings: + +SAMA5 SoCs embed an advanced NAND controller logic to automate READ/WRITE page +operations. This interface to this logic is placed in a separate I/O range and +should thus have its own DT node. + +- compatible: should be "atmel,sama5d3-nfc-io", "syscon". +- reg: should contain the I/O range used to interact with the NFC logic. + +Example: + + nfc_io: nfc-io@70000000 { + compatible = "atmel,sama5d3-nfc-io", "syscon"; + reg = <0x70000000 0x8000000>; + }; + + pmecc: ecc-engine@ffffc070 { + compatible = "atmel,at91sam9g45-pmecc"; + reg = <0xffffc070 0x490>, + <0xffffc500 0x100>; + }; + + ebi: ebi@10000000 { + compatible = "atmel,sama5d3-ebi"; + #address-cells = <2>; + #size-cells = <1>; + atmel,smc = <&hsmc>; + reg = <0x10000000 0x10000000 + 0x40000000 0x30000000>; + ranges = <0x0 0x0 0x10000000 0x10000000 + 0x1 0x0 0x40000000 0x10000000 + 0x2 0x0 0x50000000 0x10000000 + 0x3 0x0 0x60000000 0x10000000>; + clocks = <&mck>; + + nand_controller: nand-controller { + compatible = "atmel,sama5d3-nand-controller"; + atmel,nfc-sram = <&nfc_sram>; + atmel,nfc-io = <&nfc_io>; + ecc-engine = <&pmecc>; + #address-cells = <2>; + #size-cells = <1>; + ranges; + + nand@3 { + reg = <0x3 0x0 0x800000>; + atmel,rb = <0>; + + /* + * Put generic NAND/MTD properties and + * subnodes here. + */ + }; + }; + }; + +----------------------------------------------------------------------- + +Deprecated bindings (should not be used in new device trees): + +Required properties: +- compatible: The possible values are: + "atmel,at91rm9200-nand" + "atmel,sama5d2-nand" + "atmel,sama5d4-nand" +- reg : should specify localbus address and size used for the chip, + and hardware ECC controller if available. + If the hardware ECC is PMECC, it should contain address and size for + PMECC and PMECC Error Location controller. + The PMECC lookup table address and size in ROM is optional. If not + specified, driver will build it in runtime. +- atmel,nand-addr-offset : offset for the address latch. +- atmel,nand-cmd-offset : offset for the command latch. +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. + +- gpios : specifies the gpio pins to control the NAND device. detect is an + optional gpio and may be set to 0 if not present. + +Optional properties: +- atmel,nand-has-dma : boolean to support dma transfer for nand read/write. +- nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default. + Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", + "soft_bch". +- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware, + capable of BCH encoding and decoding, on devices where it is present. +- atmel,pmecc-cap : error correct capability for Programmable Multibit ECC + Controller. Supported values are: 2, 4, 8, 12, 24. If the compatible string + is "atmel,sama5d2-nand", 32 is also valid. +- atmel,pmecc-sector-size : sector size for ECC computation. Supported values + are: 512, 1024. +- atmel,pmecc-lookup-table-offset : includes two offsets of lookup table in ROM + for different sector size. First one is for sector size 512, the next is for + sector size 1024. If not specified, driver will build the table in runtime. +- nand-bus-width : 8 or 16 bus width if not present 8 +- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false + +Nand Flash Controller(NFC) is an optional sub-node +Required properties: +- compatible : "atmel,sama5d3-nfc". +- reg : should specify the address and size used for NFC command registers, + NFC registers and NFC SRAM. NFC SRAM address and size can be absent + if don't want to use it. +- clocks: phandle to the peripheral clock +Optional properties: +- atmel,write-by-sram: boolean to enable NFC write by SRAM. + +Examples: +nand0: nand@40000000,0 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000 + 0xffffe800 0x200 + >; + atmel,nand-addr-offset = <21>; /* ale */ + atmel,nand-cmd-offset = <22>; /* cle */ + nand-on-flash-bbt; + nand-ecc-mode = "soft"; + gpios = <&pioC 13 0 /* rdy */ + &pioC 14 0 /* nce */ + 0 /* cd */ + >; + partition@0 { + ... + }; +}; + +/* for PMECC supported chips */ +nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = < 0x40000000 0x10000000 /* bus addr & size */ + 0xffffe000 0x00000600 /* PMECC addr & size */ + 0xffffe600 0x00000200 /* PMECC ERRLOC addr & size */ + 0x00100000 0x00100000 /* ROM addr & size */ + >; + atmel,nand-addr-offset = <21>; /* ale */ + atmel,nand-cmd-offset = <22>; /* cle */ + nand-on-flash-bbt; + nand-ecc-mode = "hw"; + atmel,has-pmecc; /* enable PMECC */ + atmel,pmecc-cap = <2>; + atmel,pmecc-sector-size = <512>; + atmel,pmecc-lookup-table-offset = <0x8000 0x10000>; + gpios = <&pioD 5 0 /* rdy */ + &pioD 4 0 /* nce */ + 0 /* cd */ + >; + partition@0 { + ... + }; +}; + +/* for NFC supported chips */ +nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ... + nfc@70000000 { + compatible = "atmel,sama5d3-nfc"; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&hsmc_clk> + reg = < + 0x70000000 0x10000000 /* NFC Command Registers */ + 0xffffc000 0x00000070 /* NFC HSMC regs */ + 0x00200000 0x00100000 /* NFC SRAM banks */ + >; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.yaml b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.yaml new file mode 100644 index 0000000000..f57e96374e --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.yaml @@ -0,0 +1,245 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/brcm,brcmnand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom STB NAND Controller + +maintainers: + - Brian Norris <computersforpeace@gmail.com> + - Kamal Dasu <kdasu.kdev@gmail.com> + +description: | + The Broadcom Set-Top Box NAND controller supports low-level access to raw NAND + flash chips. It has a memory-mapped register interface for both control + registers and for its data input/output buffer. On some SoCs, this controller + is paired with a custom DMA engine (inventively named "Flash DMA") which + supports basic PROGRAM and READ functions, among other features. + + This controller was originally designed for STB SoCs (BCM7xxx) but is now + available on a variety of Broadcom SoCs, including some BCM3xxx, BCM63xx, and + iProc/Cygnus. Its history includes several similar (but not fully register + compatible) versions. + + -- Additional SoC-specific NAND controller properties -- + + The NAND controller is integrated differently on the variety of SoCs on which + it is found. Part of this integration involves providing status and enable + bits with which to control the 8 exposed NAND interrupts, as well as hardware + for configuring the endianness of the data bus. On some SoCs, these features + are handled via standard, modular components (e.g., their interrupts look like + a normal IRQ chip), but on others, they are controlled in unique and + interesting ways, sometimes with registers that lump multiple NAND-related + functions together. The former case can be described simply by the standard + interrupts properties in the main controller node. But for the latter + exceptional cases, we define additional 'compatible' properties and associated + register resources within the NAND controller node above. + +properties: + compatible: + oneOf: + - items: + - enum: + - brcm,brcmnand-v2.1 + - brcm,brcmnand-v2.2 + - brcm,brcmnand-v4.0 + - brcm,brcmnand-v5.0 + - brcm,brcmnand-v6.0 + - brcm,brcmnand-v6.1 + - brcm,brcmnand-v6.2 + - brcm,brcmnand-v7.0 + - brcm,brcmnand-v7.1 + - brcm,brcmnand-v7.2 + - brcm,brcmnand-v7.3 + - const: brcm,brcmnand + - description: BCM63138 SoC-specific NAND controller + items: + - const: brcm,nand-bcm63138 + - enum: + - brcm,brcmnand-v7.0 + - brcm,brcmnand-v7.1 + - const: brcm,brcmnand + - description: iProc SoC-specific NAND controller + items: + - const: brcm,nand-iproc + - const: brcm,brcmnand-v6.1 + - const: brcm,brcmnand + - description: BCM63168 SoC-specific NAND controller + items: + - const: brcm,nand-bcm63168 + - const: brcm,nand-bcm6368 + - const: brcm,brcmnand-v4.0 + - const: brcm,brcmnand + + reg: + minItems: 1 + maxItems: 6 + + reg-names: + minItems: 1 + maxItems: 6 + items: + enum: [ nand, flash-dma, flash-edu, nand-cache, nand-int-base, iproc-idm, iproc-ext ] + + interrupts: + minItems: 1 + items: + - description: NAND CTLRDY interrupt + - description: FLASH_DMA_DONE (if flash DMA is available) or FLASH_EDU_DONE (if EDU is available) + + interrupt-names: + minItems: 1 + items: + - const: nand_ctlrdy + - enum: + - flash_dma_done + - flash_edu_done + + clocks: + maxItems: 1 + description: reference to the clock for the NAND controller + + clock-names: + const: nand + + brcm,nand-has-wp: + description: > + Some versions of this IP include a write-protect + (WP) control bit. It is always available on >= + v7.0. Use this property to describe the rare + earlier versions of this core that include WP + type: boolean + +patternProperties: + "^nand@[a-f0-9]$": + type: object + $ref: raw-nand-chip.yaml + properties: + compatible: + const: brcm,nandcs + + nand-ecc-step-size: + enum: [ 512, 1024 ] + + brcm,nand-oob-sector-size: + description: | + integer, to denote the spare area sector size + expected for the ECC layout in use. This size, in + addition to the strength and step-size, + determines how the hardware BCH engine will lay + out the parity bytes it stores on the flash. + This property can be automatically determined by + the flash geometry (particularly the NAND page + and OOB size) in many cases, but when booting + from NAND, the boot controller has only a limited + number of available options for its default ECC + layout. + $ref: /schemas/types.yaml#/definitions/uint32 + + unevaluatedProperties: false + +allOf: + - $ref: nand-controller.yaml# + - if: + properties: + compatible: + contains: + const: brcm,nand-bcm63138 + then: + properties: + reg-names: + items: + - const: nand + - const: nand-int-base + - if: + properties: + compatible: + contains: + const: brcm,nand-bcm6368 + then: + properties: + reg-names: + items: + - const: nand + - const: nand-int-base + - const: nand-cache + - if: + properties: + compatible: + contains: + const: brcm,nand-iproc + then: + properties: + reg-names: + items: + - const: nand + - const: iproc-idm + - const: iproc-ext + - if: + properties: + interrupts: + minItems: 2 + then: + required: + - interrupt-names + +unevaluatedProperties: false + +required: + - reg + - reg-names + - interrupts + +examples: + - | + nand-controller@f0442800 { + compatible = "brcm,brcmnand-v7.0", "brcm,brcmnand"; + reg = <0xf0442800 0x600>, + <0xf0443000 0x100>; + reg-names = "nand", "flash-dma"; + interrupt-parent = <&hif_intr2_intc>; + interrupts = <24>, <4>; + interrupt-names = "nand_ctlrdy", "flash_dma_done"; + + #address-cells = <1>; + #size-cells = <0>; + + nand@1 { + compatible = "brcm,nandcs"; + reg = <1>; // Chip select 1 + nand-on-flash-bbt; + nand-ecc-strength = <12>; + nand-ecc-step-size = <512>; + + #address-cells = <1>; + #size-cells = <1>; + }; + }; + - | + nand-controller@10000200 { + compatible = "brcm,nand-bcm63168", "brcm,nand-bcm6368", + "brcm,brcmnand-v4.0", "brcm,brcmnand"; + reg = <0x10000200 0x180>, + <0x100000b0 0x10>, + <0x10000600 0x200>; + reg-names = "nand", "nand-int-base", "nand-cache"; + interrupt-parent = <&periph_intc>; + interrupts = <50>; + clocks = <&periph_clk 20>; + clock-names = "nand"; + + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + compatible = "brcm,nandcs"; + reg = <0>; + nand-on-flash-bbt; + nand-ecc-strength = <1>; + nand-ecc-step-size = <512>; + + #address-cells = <1>; + #size-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/cadence-nand-controller.txt b/Documentation/devicetree/bindings/mtd/cadence-nand-controller.txt new file mode 100644 index 0000000000..d2eada5044 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/cadence-nand-controller.txt @@ -0,0 +1,53 @@ +* Cadence NAND controller + +Required properties: + - compatible : "cdns,hp-nfc" + - reg : Contains two entries, each of which is a tuple consisting of a + physical address and length. The first entry is the address and + length of the controller register set. The second entry is the + address and length of the Slave DMA data port. + - reg-names: should contain "reg" and "sdma" + - #address-cells: should be 1. The cell encodes the chip select connection. + - #size-cells : should be 0. + - interrupts : The interrupt number. + - clocks: phandle of the controller core clock (nf_clk). + +Optional properties: + - dmas: shall reference DMA channel associated to the NAND controller + - cdns,board-delay-ps : Estimated Board delay. The value includes the total + round trip delay for the signals and is used for deciding on values + associated with data read capture. The example formula for SDR mode is + the following: + board delay = RE#PAD delay + PCB trace to device + PCB trace from device + + DQ PAD delay + +Child nodes represent the available NAND chips. + +Required properties of NAND chips: + - reg: shall contain the native Chip Select ids from 0 to max supported by + the cadence nand flash controller + +See Documentation/devicetree/bindings/mtd/nand-controller.yaml for more details on +generic bindings. + +Example: + +nand_controller: nand-controller@60000000 { + compatible = "cdns,hp-nfc"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x60000000 0x10000>, <0x80000000 0x10000>; + reg-names = "reg", "sdma"; + clocks = <&nf_clk>; + cdns,board-delay-ps = <4830>; + interrupts = <2 0>; + nand@0 { + reg = <0>; + label = "nand-1"; + }; + nand@1 { + reg = <1>; + label = "nand-2"; + }; + +}; diff --git a/Documentation/devicetree/bindings/mtd/davinci-nand.txt b/Documentation/devicetree/bindings/mtd/davinci-nand.txt new file mode 100644 index 0000000000..edebeae1f5 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/davinci-nand.txt @@ -0,0 +1,94 @@ +Device tree bindings for Texas instruments Davinci/Keystone NAND controller + +This file provides information, what the device node for the davinci/keystone +NAND interface contains. + +Documentation: +Davinci DM646x - https://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf +Kestone - https://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf + +Required properties: + +- compatible: "ti,davinci-nand" + "ti,keystone-nand" + +- reg: Contains 2 offset/length values: + - offset and length for the access window. + - offset and length for accessing the AEMIF + control registers. + +- ti,davinci-chipselect: number of chipselect. Indicates on the + davinci_nand driver which chipselect is used + for accessing the nand. + Can be in the range [0-3]. + +Recommended properties : + +- ti,davinci-mask-ale: mask for ALE. Needed for executing address + phase. These offset will be added to the base + address for the chip select space the NAND Flash + device is connected to. + If not set equal to 0x08. + +- ti,davinci-mask-cle: mask for CLE. Needed for executing command + phase. These offset will be added to the base + address for the chip select space the NAND Flash + device is connected to. + If not set equal to 0x10. + +- ti,davinci-mask-chipsel: mask for chipselect address. Needed to mask + addresses for given chipselect. + +- nand-ecc-mode: operation mode of the NAND ecc mode. ECC mode + valid values for davinci driver: + - "none" + - "soft" + - "hw" + +- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4. + +- nand-bus-width: buswidth 8 or 16. If not present 8. + +- nand-on-flash-bbt: use flash based bad block table support. OOB + identifier is saved in OOB area. If not present + false. + +Deprecated properties: + +- ti,davinci-ecc-mode: operation mode of the NAND ecc mode. ECC mode + valid values for davinci driver: + - "none" + - "soft" + - "hw" + +- ti,davinci-nand-buswidth: buswidth 8 or 16. If not present 8. + +- ti,davinci-nand-use-bbt: use flash based bad block table support. OOB + identifier is saved in OOB area. If not present + false. + +Nand device bindings may contain additional sub-nodes describing partitions of +the address space. See partition.txt for more detail. The NAND Flash timing +values must be programmed in the chip select’s node of AEMIF +memory-controller (see Documentation/devicetree/bindings/memory-controllers/ +davinci-aemif.txt). + +Example(da850 EVM ): + +nand_cs3@62000000 { + compatible = "ti,davinci-nand"; + reg = <0x62000000 0x807ff + 0x68000000 0x8000>; + ti,davinci-chipselect = <1>; + ti,davinci-mask-ale = <0>; + ti,davinci-mask-cle = <0>; + ti,davinci-mask-chipsel = <0>; + nand-ecc-mode = "hw"; + ti,davinci-ecc-bits = <4>; + nand-on-flash-bbt; + + partition@180000 { + label = "ubifs"; + reg = <0x180000 0x7e80000>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/denali,nand.yaml b/Documentation/devicetree/bindings/mtd/denali,nand.yaml new file mode 100644 index 0000000000..81f95538d4 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/denali,nand.yaml @@ -0,0 +1,153 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/denali,nand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Denali NAND controller + +maintainers: + - Masahiro Yamada <yamada.masahiro@socionext.com> + +properties: + compatible: + enum: + - altr,socfpga-denali-nand + - socionext,uniphier-denali-nand-v5a + - socionext,uniphier-denali-nand-v5b + + reg-names: + description: | + There are two register regions: + nand_data: host data/command interface + denali_reg: register interface + items: + - const: nand_data + - const: denali_reg + + reg: + minItems: 2 + maxItems: 2 + + interrupts: + maxItems: 1 + + clock-names: + description: | + There are three clocks: + nand: controller core clock + nand_x: bus interface clock + ecc: ECC circuit clock + items: + - const: nand + - const: nand_x + - const: ecc + + clocks: + minItems: 3 + maxItems: 3 + + reset-names: + description: | + There are two optional resets: + nand: controller core reset + reg: register reset + oneOf: + - items: + - const: nand + - const: reg + - const: nand + - const: reg + + resets: + minItems: 1 + maxItems: 2 + +patternProperties: + "^nand@[a-f0-9]$": + type: object + $ref: raw-nand-chip.yaml + unevaluatedProperties: false + +allOf: + - $ref: nand-controller.yaml + + - if: + properties: + compatible: + contains: + const: altr,socfpga-denali-nand + then: + patternProperties: + "^nand@[a-f0-9]$": + properties: + nand-ecc-strength: + enum: + - 8 + - 15 + nand-ecc-step-size: + enum: + - 512 + + - if: + properties: + compatible: + contains: + const: socionext,uniphier-denali-nand-v5a + then: + patternProperties: + "^nand@[a-f0-9]$": + properties: + nand-ecc-strength: + enum: + - 8 + - 16 + - 24 + nand-ecc-step-size: + enum: + - 1024 + + - if: + properties: + compatible: + contains: + const: socionext,uniphier-denali-nand-v5b + then: + patternProperties: + "^nand@[a-f0-9]$": + properties: + nand-ecc-strength: + enum: + - 8 + - 16 + nand-ecc-step-size: + enum: + - 1024 + +required: + - compatible + - reg + - interrupts + - clock-names + - clocks + +unevaluatedProperties: false + +examples: + - | + nand-controller@ff900000 { + compatible = "altr,socfpga-denali-nand"; + reg-names = "nand_data", "denali_reg"; + reg = <0xff900000 0x20>, <0xffb80000 0x1000>; + interrupts = <0 144 4>; + clock-names = "nand", "nand_x", "ecc"; + clocks = <&nand_clk>, <&nand_x_clk>, <&nand_ecc_clk>; + reset-names = "nand", "reg"; + resets = <&nand_rst>, <&nand_reg_rst>; + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/diskonchip.txt b/Documentation/devicetree/bindings/mtd/diskonchip.txt new file mode 100644 index 0000000000..3e13bfdbea --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/diskonchip.txt @@ -0,0 +1,15 @@ +M-Systems and Sandisk DiskOnChip devices + +M-System DiskOnChip G3 +====================== +The Sandisk (formerly M-Systems) docg3 is a nand device of 64M to 256MB. + +Required properties: + - compatible: should be "m-systems,diskonchip-g3" + - reg: register base and size + +Example: + docg3: flash@0 { + compatible = "m-systems,diskonchip-g3"; + reg = <0x0 0x2000>; + }; diff --git a/Documentation/devicetree/bindings/mtd/flctl-nand.txt b/Documentation/devicetree/bindings/mtd/flctl-nand.txt new file mode 100644 index 0000000000..427f46dc60 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/flctl-nand.txt @@ -0,0 +1,49 @@ +FLCTL NAND controller + +Required properties: +- compatible : "renesas,shmobile-flctl-sh7372" +- reg : Address range of the FLCTL +- interrupts : flste IRQ number +- nand-bus-width : bus width to NAND chip + +Optional properties: +- dmas: DMA specifier(s) +- dma-names: name for each DMA specifier. Valid names are + "data_tx", "data_rx", "ecc_tx", "ecc_rx" + +The DMA fields are not used yet in the driver but are listed here for +completing the bindings. + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + + flctl@e6a30000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "renesas,shmobile-flctl-sh7372"; + reg = <0xe6a30000 0x100>; + interrupts = <0x0d80>; + + nand-bus-width = <16>; + + dmas = <&dmac 1 /* data_tx */ + &dmac 2;> /* data_rx */ + dma-names = "data_tx", "data_rx"; + + system@0 { + label = "system"; + reg = <0x0 0x8000000>; + }; + + userdata@8000000 { + label = "userdata"; + reg = <0x8000000 0x10000000>; + }; + + cache@18000000 { + label = "cache"; + reg = <0x18000000 0x8000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt new file mode 100644 index 0000000000..25f07c1f9e --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt @@ -0,0 +1,67 @@ +Freescale Localbus UPM programmed to work with NAND flash + +Required properties: +- compatible : "fsl,upm-nand". +- reg : should specify localbus chip select and size used for the chip. +- fsl,upm-addr-offset : UPM pattern offset for the address latch. +- fsl,upm-cmd-offset : UPM pattern offset for the command latch. + +Optional properties: +- fsl,upm-addr-line-cs-offsets : address offsets for multi-chip support. + The corresponding address lines are used to select the chip. +- gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins + (R/B#). For multi-chip devices, "n" GPIO definitions are required + according to the number of chips. + +Deprecated properties: +- fsl,upm-wait-flags : add chip-dependent short delays after running the + UPM pattern (0x1), after writing a data byte (0x2) or after + writing out a buffer (0x4). +- chip-delay : chip dependent delay for transferring data from array to + read registers (tR). Required if property "gpios" is not used + (R/B# pins not connected). + +Each flash chip described may optionally contain additional sub-nodes +describing partitions of the address space. See partition.txt for more +detail. + +Examples: + +upm@1,0 { + compatible = "fsl,upm-nand"; + reg = <1 0 1>; + fsl,upm-addr-offset = <16>; + fsl,upm-cmd-offset = <8>; + gpios = <&qe_pio_e 18 0>; + + flash { + #address-cells = <1>; + #size-cells = <1>; + compatible = "..."; + + partition@0 { + ... + }; + }; +}; + +upm@3,0 { + #address-cells = <0>; + #size-cells = <0>; + compatible = "tqc,tqm8548-upm-nand", "fsl,upm-nand"; + reg = <3 0x0 0x800>; + fsl,upm-addr-offset = <0x10>; + fsl,upm-cmd-offset = <0x08>; + /* Multi-chip NAND device */ + fsl,upm-addr-line-cs-offsets = <0x0 0x200>; + + nand@0 { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "fs"; + reg = <0x00000000 0x10000000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt new file mode 100644 index 0000000000..6762d3c4d5 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -0,0 +1,60 @@ +ST Microelectronics Flexible Static Memory Controller (FSMC) +NAND Interface + +Required properties: +- compatible : "st,spear600-fsmc-nand", "stericsson,fsmc-nand" +- reg : Address range of the mtd chip +- reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd" + +Optional properties: +- bank-width : Width (in bytes) of the device. If not present, the width + defaults to 1 byte +- nand-skip-bbtscan: Indicates the BBT scanning should be skipped +- timings: array of 6 bytes for NAND timings. The meanings of these bytes + are: + byte 0 TCLR : CLE to RE delay in number of AHB clock cycles, only 4 bits + are valid. Zero means one clockcycle, 15 means 16 clock + cycles. + byte 1 TAR : ALE to RE delay, 4 bits are valid. Same format as TCLR. + byte 2 THIZ : number of HCLK clock cycles during which the data bus is + kept in Hi-Z (tristate) after the start of a write access. + Only valid for write transactions. Zero means zero cycles, + 255 means 255 cycles. + byte 3 THOLD : number of HCLK clock cycles to hold the address (and data + when writing) after the command deassertation. Zero means + one cycle, 255 means 256 cycles. + byte 4 TWAIT : number of HCLK clock cycles to assert the command to the + NAND flash in response to SMWAITn. Zero means 1 cycle, + 255 means 256 cycles. + byte 5 TSET : number of HCLK clock cycles to assert the address before the + command is asserted. Zero means one cycle, 255 means 256 + cycles. +- bank: default NAND bank to use (0-3 are valid, 0 is the default). +- nand-ecc-mode : see nand-controller.yaml +- nand-ecc-strength : see nand-controller.yaml +- nand-ecc-step-size : see nand-controller.yaml + +Can support 1-bit HW ECC (default) or if stronger correction is required, +software-based BCH. + +Example: + + fsmc: flash@d1800000 { + compatible = "st,spear600-fsmc-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xd1800000 0x1000 /* FSMC Register */ + 0xd2000000 0x0010 /* NAND Base DATA */ + 0xd2020000 0x0010 /* NAND Base ADDR */ + 0xd2010000 0x0010>; /* NAND Base CMD */ + reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd"; + + bank-width = <1>; + nand-skip-bbtscan; + timings = /bits/ 8 <0 0 0 2 3 0>; + bank = <1>; + + partition@0 { + ... + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt new file mode 100644 index 0000000000..486a17d533 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt @@ -0,0 +1,47 @@ +GPIO assisted NAND flash + +The GPIO assisted NAND flash uses a memory mapped interface to +read/write the NAND commands and data and GPIO pins for the control +signals. + +Required properties: +- compatible : "gpio-control-nand" +- reg : should specify localbus chip select and size used for the chip. The + resource describes the data bus connected to the NAND flash and all accesses + are made in native endianness. +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. +- gpios : Specifies the GPIO pins to control the NAND device. The order of + GPIO references is: RDY, nCE, ALE, CLE, and nWP. nCE and nWP are optional. + +Optional properties: +- bank-width : Width (in bytes) of the device. If not present, the width + defaults to 1 byte. +- chip-delay : chip dependent delay for transferring data from array to + read registers (tR). If not present then a default of 20us is used. +- gpio-control-nand,io-sync-reg : A 64-bit physical address for a read + location used to guard against bus reordering with regards to accesses to + the GPIO's and the NAND flash data bus. If present, then after changing + GPIO state and before and after command byte writes, this register will be + read to ensure that the GPIO accesses have completed. + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Examples: + +gpio-nand@1,0 { + compatible = "gpio-control-nand"; + reg = <1 0x0000 0x2>; + #address-cells = <1>; + #size-cells = <1>; + gpios = <&banka 1 0>, /* RDY */ + <0>, /* nCE */ + <&banka 3 0>, /* ALE */ + <&banka 4 0>, /* CLE */ + <0>; /* nWP */ + + partition@0 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.yaml b/Documentation/devicetree/bindings/mtd/gpmi-nand.yaml new file mode 100644 index 0000000000..ba086c3462 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.yaml @@ -0,0 +1,168 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale General-Purpose Media Interface (GPMI) + +maintainers: + - Han Xu <han.xu@nxp.com> + +description: | + The GPMI nand controller provides an interface to control the NAND + flash chips. The device tree may optionally contain sub-nodes + describing partitions of the address space. See partition.txt for + more detail. + +properties: + compatible: + oneOf: + - enum: + - fsl,imx23-gpmi-nand + - fsl,imx28-gpmi-nand + - fsl,imx6q-gpmi-nand + - fsl,imx6sx-gpmi-nand + - fsl,imx7d-gpmi-nand + - items: + - enum: + - fsl,imx8mm-gpmi-nand + - fsl,imx8mn-gpmi-nand + - const: fsl,imx7d-gpmi-nand + + reg: + items: + - description: Address and length of gpmi block. + - description: Address and length of bch block. + + reg-names: + items: + - const: gpmi-nand + - const: bch + + interrupts: + maxItems: 1 + + interrupt-names: + const: bch + + dmas: + maxItems: 1 + + dma-names: + const: rx-tx + + clocks: + minItems: 1 + maxItems: 5 + + clock-names: + minItems: 1 + maxItems: 5 + + fsl,use-minimum-ecc: + type: boolean + description: | + Protect this NAND flash with the minimum ECC strength required. + The required ECC strength is automatically discoverable for some + flash (e.g., according to the ONFI standard). However, note that + if this strength is not discoverable or this property is not enabled, + the software may chooses an implementation-defined ECC scheme. + + fsl,no-blockmark-swap: + type: boolean + description: | + Don't swap the bad block marker from the OOB area with the byte in + the data area but rely on the flash based BBT for identifying bad blocks. + NOTE: this is only valid in conjunction with 'nand-on-flash-bbt'. + WARNING: on i.MX28 blockmark swapping cannot be disabled for the BootROM + in the FCB. Thus, partitions written from Linux with this feature turned + on may not be accessible by the BootROM code. + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-names + - clocks + - clock-names + - dmas + - dma-names + +unevaluatedProperties: false + +allOf: + - $ref: nand-controller.yaml + + - if: + properties: + compatible: + contains: + enum: + - fsl,imx23-gpmi-nand + - fsl,imx28-gpmi-nand + then: + properties: + clocks: + items: + - description: SoC gpmi io clock + clock-names: + items: + - const: gpmi_io + + - if: + properties: + compatible: + contains: + enum: + - fsl,imx6q-gpmi-nand + - fsl,imx6sx-gpmi-nand + then: + properties: + clocks: + items: + - description: SoC gpmi io clock + - description: SoC gpmi apb clock + - description: SoC gpmi bch clock + - description: SoC gpmi bch apb clock + - description: SoC per1 bch clock + clock-names: + items: + - const: gpmi_io + - const: gpmi_apb + - const: gpmi_bch + - const: gpmi_bch_apb + - const: per1_bch + + - if: + properties: + compatible: + contains: + const: fsl,imx7d-gpmi-nand + then: + properties: + clocks: + items: + - description: SoC gpmi io clock + - description: SoC gpmi bch apb clock + clock-names: + items: + - const: gpmi_io + - const: gpmi_bch_apb + +examples: + - | + nand-controller@8000c000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-gpmi-nand"; + reg = <0x8000c000 0x2000>, <0x8000a000 0x2000>; + reg-names = "gpmi-nand", "bch"; + interrupts = <41>; + interrupt-names = "bch"; + clocks = <&clks 50>; + clock-names = "gpmi_io"; + dmas = <&dma_apbh 4>; + dma-names = "rx-tx"; + }; diff --git a/Documentation/devicetree/bindings/mtd/hisi504-nand.txt b/Documentation/devicetree/bindings/mtd/hisi504-nand.txt new file mode 100644 index 0000000000..8963983ae7 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/hisi504-nand.txt @@ -0,0 +1,47 @@ +Hisilicon Hip04 Soc NAND controller DT binding + +Required properties: + +- compatible: Should be "hisilicon,504-nfc". +- reg: The first contains base physical address and size of + NAND controller's registers. The second contains base + physical address and size of NAND controller's buffer. +- interrupts: Interrupt number for nfc. +- nand-bus-width: See nand-controller.yaml. +- nand-ecc-mode: Support none and hw ecc mode. +- #address-cells: Partition address, should be set 1. +- #size-cells: Partition size, should be set 1. + +Optional properties: + +- nand-ecc-strength: Number of bits to correct per ECC step. +- nand-ecc-step-size: Number of data bytes covered by a single ECC step. + +The following ECC strength and step size are currently supported: + + - nand-ecc-strength = <16>, nand-ecc-step-size = <1024> + +Flash chip may optionally contain additional sub-nodes describing partitions of +the address space. See partition.txt for more detail. + +Example: + + nand: nand@4020000 { + compatible = "hisilicon,504-nfc"; + reg = <0x4020000 0x10000>, <0x5000000 0x1000>; + interrupts = <0 379 4>; + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <16>; + nand-ecc-step-size = <1024>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "nand_text"; + reg = <0x00000000 0x00400000>; + }; + + ... + + }; diff --git a/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt b/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt new file mode 100644 index 0000000000..a99de13c7c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt @@ -0,0 +1,24 @@ +HiSilicon SPI-NOR Flash Controller + +Required properties: +- compatible : Should be "hisilicon,fmc-spi-nor" and one of the following strings: + "hisilicon,hi3519-spi-nor" +- address-cells : Should be 1. +- size-cells : Should be 0. +- reg : Offset and length of the register set for the controller device. +- reg-names : Must include the following two entries: "control", "memory". +- clocks : handle to spi-nor flash controller clock. + +Example: +spi-nor-controller@10000000 { + compatible = "hisilicon,hi3519-spi-nor", "hisilicon,fmc-spi-nor"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10000000 0x1000>, <0x14000000 0x1000000>; + reg-names = "control", "memory"; + clocks = <&clock HI3519_FMC_CLK>; + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/ibm,ndfc.txt b/Documentation/devicetree/bindings/mtd/ibm,ndfc.txt new file mode 100644 index 0000000000..869f0b5f16 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/ibm,ndfc.txt @@ -0,0 +1,39 @@ +AMCC NDFC (NanD Flash Controller) + +Required properties: +- compatible : "ibm,ndfc". +- reg : should specify chip select and size used for the chip (0x2000). + +Optional properties: +- ccr : NDFC config and control register value (default 0). +- bank-settings : NDFC bank configuration register value (default 0). + +Notes: +- partition(s) - follows the OF MTD standard for partitions + +Example: + +ndfc@1,0 { + compatible = "ibm,ndfc"; + reg = <0x00000001 0x00000000 0x00002000>; + ccr = <0x00001000>; + bank-settings = <0x80002222>; + #address-cells = <1>; + #size-cells = <1>; + + nand { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x00000000 0x00200000>; + }; + partition@200000 { + label = "root"; + reg = <0x00200000 0x03E00000>; + }; + }; +}; + + diff --git a/Documentation/devicetree/bindings/mtd/ingenic,nand.yaml b/Documentation/devicetree/bindings/mtd/ingenic,nand.yaml new file mode 100644 index 0000000000..b9312ebefe --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/ingenic,nand.yaml @@ -0,0 +1,139 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/ingenic,nand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ingenic SoCs NAND controller + +maintainers: + - Paul Cercueil <paul@crapouillou.net> + +allOf: + - $ref: nand-controller.yaml# + - $ref: /schemas/memory-controllers/ingenic,nemc-peripherals.yaml# + +properties: + compatible: + enum: + - ingenic,jz4740-nand + - ingenic,jz4725b-nand + - ingenic,jz4780-nand + + reg: + items: + - description: Bank number, offset and size of first attached NAND chip + - description: Bank number, offset and size of second attached NAND chip + - description: Bank number, offset and size of third attached NAND chip + - description: Bank number, offset and size of fourth attached NAND chip + minItems: 1 + + ecc-engine: true + + partitions: + type: object + deprecated: true + description: + Node containing description of fixed partitions. + +patternProperties: + "^nand@[a-f0-9]$": + type: object + $ref: raw-nand-chip.yaml + properties: + + rb-gpios: + description: GPIO specifier for the busy pin. + maxItems: 1 + + wp-gpios: + description: GPIO specifier for the write-protect pin. + maxItems: 1 + + unevaluatedProperties: false + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/ingenic,jz4780-cgu.h> + memory-controller@13410000 { + compatible = "ingenic,jz4780-nemc"; + reg = <0x13410000 0x10000>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <1 0 0x1b000000 0x1000000>, + <2 0 0x1a000000 0x1000000>, + <3 0 0x19000000 0x1000000>, + <4 0 0x18000000 0x1000000>, + <5 0 0x17000000 0x1000000>, + <6 0 0x16000000 0x1000000>; + + clocks = <&cgu JZ4780_CLK_NEMC>; + + nand-controller@1 { + compatible = "ingenic,jz4780-nand"; + reg = <1 0 0x1000000>; + + #address-cells = <1>; + #size-cells = <0>; + + ecc-engine = <&bch>; + + ingenic,nemc-tAS = <10>; + ingenic,nemc-tAH = <5>; + ingenic,nemc-tBP = <10>; + ingenic,nemc-tAW = <15>; + ingenic,nemc-tSTRV = <100>; + + pinctrl-names = "default"; + pinctrl-0 = <&pins_nemc>; + + nand@1 { + reg = <1>; + + nand-ecc-step-size = <1024>; + nand-ecc-strength = <24>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + + pinctrl-names = "default"; + pinctrl-0 = <&pins_nemc_cs1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <2>; + #size-cells = <2>; + + partition@0 { + label = "u-boot-spl"; + reg = <0x0 0x0 0x0 0x800000>; + }; + + partition@800000 { + label = "u-boot"; + reg = <0x0 0x800000 0x0 0x200000>; + }; + + partition@a00000 { + label = "u-boot-env"; + reg = <0x0 0xa00000 0x0 0x200000>; + }; + + partition@c00000 { + label = "boot"; + reg = <0x0 0xc00000 0x0 0x4000000>; + }; + + partition@4c00000 { + label = "system"; + reg = <0x0 0x4c00000 0x1 0xfb400000>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/intel,lgm-ebunand.yaml b/Documentation/devicetree/bindings/mtd/intel,lgm-ebunand.yaml new file mode 100644 index 0000000000..07bc7e3efd --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/intel,lgm-ebunand.yaml @@ -0,0 +1,90 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/intel,lgm-ebunand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Intel LGM SoC NAND Controller + +allOf: + - $ref: nand-controller.yaml + +maintainers: + - Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com> + +properties: + compatible: + const: intel,lgm-ebunand + + reg: + maxItems: 6 + + reg-names: + items: + - const: ebunand + - const: hsnand + - const: nand_cs0 + - const: nand_cs1 + - const: addr_sel0 + - const: addr_sel1 + + clocks: + maxItems: 1 + + dmas: + maxItems: 2 + + dma-names: + items: + - const: tx + - const: rx + +patternProperties: + "^nand@[a-f0-9]$": + type: object + $ref: raw-nand-chip.yaml + properties: + reg: + minimum: 0 + maximum: 1 + + nand-ecc-algo: + const: hw + + unevaluatedProperties: false + +required: + - compatible + - reg + - reg-names + - clocks + - dmas + - dma-names + +unevaluatedProperties: false + +examples: + - | + nand-controller@e0f00000 { + compatible = "intel,lgm-ebunand"; + reg = <0xe0f00000 0x100>, + <0xe1000000 0x300>, + <0xe1400000 0x8000>, + <0xe1c00000 0x1000>, + <0x17400000 0x4>, + <0x17c00000 0x4>; + reg-names = "ebunand", "hsnand", "nand_cs0", "nand_cs1", + "addr_sel0", "addr_sel1"; + clocks = <&cgu0 125>; + dmas = <&dma0 8>, <&dma0 9>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + nand-ecc-mode = "hw"; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml new file mode 100644 index 0000000000..58f0cea160 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml @@ -0,0 +1,120 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/jedec,spi-nor.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SPI NOR flash ST M25Pxx (and similar) serial flash chips + +maintainers: + - Rob Herring <robh@kernel.org> + +allOf: + - $ref: mtd.yaml# + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +properties: + compatible: + oneOf: + - items: + - pattern: "^((((micron|spansion|st),)?\ + (m25p(40|80|16|32|64|128)|\ + n25q(32b|064|128a11|128a13|256a|512a|164k)))|\ + atmel,at25df(321a|641|081a)|\ + everspin,mr25h(10|40|128|256)|\ + (mxicy|macronix),mx25l(4005a|1606e|6405d|8005|12805d|25635e)|\ + (mxicy|macronix),mx25u(4033|4035)|\ + (spansion,)?s25fl(128s|256s1|512s|008k|064k|164k)|\ + (sst|microchip),sst25vf(016b|032b|040b)|\ + (sst,)?sst26wf016b|\ + (sst,)?sst25wf(040b|080)|\ + winbond,w25x(80|32)|\ + (winbond,)?w25q(16|32(w|dw)?|64(dw)?|80bl|128(fw)?|256))$" + - const: jedec,spi-nor + - items: + - enum: + - issi,is25lp016d + - micron,mt25qu02g + - mxicy,mx25r1635f + - mxicy,mx25u6435f + - mxicy,mx25v8035f + - spansion,s25sl12801 + - spansion,s25fs512s + - const: jedec,spi-nor + - const: jedec,spi-nor + description: + SPI NOR flashes compatible with the JEDEC SFDP standard or which may be + identified with the READ ID opcode (0x9F) do not deserve a specific + compatible. They should instead only be matched against the generic + "jedec,spi-nor" compatible. + + reg: + minItems: 1 + maxItems: 2 + + m25p,fast-read: + type: boolean + description: + Use the "fast read" opcode to read data from the chip instead of the usual + "read" opcode. This opcode is not supported by all chips and support for + it can not be detected at runtime. Refer to your chips' datasheet to check + if this is supported by your chip. + + broken-flash-reset: + type: boolean + description: + Some flash devices utilize stateful addressing modes (e.g., for 32-bit + addressing) which need to be managed carefully by a system. Because these + sorts of flash don't have a standardized software reset command, and + because some systems don't toggle the flash RESET# pin upon system reset + (if the pin even exists at all), there are systems which cannot reboot + properly if the flash is left in the "wrong" state. This boolean flag can + be used on such systems, to denote the absence of a reliable reset + mechanism. + + no-wp: + type: boolean + description: + The status register write disable (SRWD) bit in status register, combined + with the WP# signal, provides hardware data protection for the device. When + the SRWD bit is set to 1, and the WP# signal is either driven LOW or hard + strapped to LOW, the status register nonvolatile bits become read-only and + the WRITE STATUS REGISTER operation will not execute. The only way to exit + this hardware-protected mode is to drive WP# HIGH. If the WP# signal of the + flash device is not connected or is wrongly tied to GND (that includes internal + pull-downs) then status register permanently becomes read-only as the SRWD bit + cannot be reset. This boolean flag can be used on such systems to avoid setting + the SRWD bit while writing the status register. WP# signal hard strapped to GND + can be a valid use case. + + reset-gpios: + description: + A GPIO line connected to the RESET (active low) signal of the device. + If "broken-flash-reset" is present then having this property does not + make any difference. + + spi-cpol: true + spi-cpha: true + +dependencies: + spi-cpol: [ spi-cpha ] + spi-cpha: [ spi-cpol ] + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + flash@0 { + compatible = "spansion,m25p80", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + m25p,fast-read; + reset-gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt b/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt new file mode 100644 index 0000000000..64c06aa05a --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt @@ -0,0 +1,50 @@ +NXP LPC32xx SoC NAND MLC controller + +Required properties: +- compatible: "nxp,lpc3220-mlc" +- reg: Address and size of the controller +- interrupts: The NAND interrupt specification +- gpios: GPIO specification for NAND write protect + +The following required properties are very controller specific. See the LPC32xx +User Manual 7.5.14 MLC NAND Timing Register (the values here are specified in +Hz, to make them independent of actual clock speed and to provide for good +accuracy:) +- nxp,tcea_delay: TCEA_DELAY +- nxp,busy_delay: BUSY_DELAY +- nxp,nand_ta: NAND_TA +- nxp,rd_high: RD_HIGH +- nxp,rd_low: RD_LOW +- nxp,wr_high: WR_HIGH +- nxp,wr_low: WR_LOW + +Optional subnodes: +- Partitions, see Documentation/devicetree/bindings/mtd/mtd.yaml + +Example: + + mlc: flash@200a8000 { + compatible = "nxp,lpc3220-mlc"; + reg = <0x200A8000 0x11000>; + interrupts = <11 0>; + #address-cells = <1>; + #size-cells = <1>; + + nxp,tcea-delay = <333333333>; + nxp,busy-delay = <10000000>; + nxp,nand-ta = <18181818>; + nxp,rd-high = <31250000>; + nxp,rd-low = <45454545>; + nxp,wr-high = <40000000>; + nxp,wr-low = <83333333>; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + + mtd0@00000000 { + label = "boot"; + reg = <0x00000000 0x00064000>; + read-only; + }; + + ... + + }; diff --git a/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt b/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt new file mode 100644 index 0000000000..39f17630a3 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt @@ -0,0 +1,52 @@ +NXP LPC32xx SoC NAND SLC controller + +Required properties: +- compatible: "nxp,lpc3220-slc" +- reg: Address and size of the controller +- nand-on-flash-bbt: Use bad block table on flash +- gpios: GPIO specification for NAND write protect + +The following required properties are very controller specific. See the LPC32xx +User Manual: +- nxp,wdr-clks: Delay before Ready signal is tested on write (W_RDY) +- nxp,rdr-clks: Delay before Ready signal is tested on read (R_RDY) +(The following values are specified in Hz, to make them independent of actual +clock speed:) +- nxp,wwidth: Write pulse width (W_WIDTH) +- nxp,whold: Write hold time (W_HOLD) +- nxp,wsetup: Write setup time (W_SETUP) +- nxp,rwidth: Read pulse width (R_WIDTH) +- nxp,rhold: Read hold time (R_HOLD) +- nxp,rsetup: Read setup time (R_SETUP) + +Optional subnodes: +- Partitions, see Documentation/devicetree/bindings/mtd/mtd.yaml + +Example: + + slc: flash@20020000 { + compatible = "nxp,lpc3220-slc"; + reg = <0x20020000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + nxp,wdr-clks = <14>; + nxp,wwidth = <40000000>; + nxp,whold = <100000000>; + nxp,wsetup = <100000000>; + nxp,rdr-clks = <14>; + nxp,rwidth = <40000000>; + nxp,rhold = <66666666>; + nxp,rsetup = <100000000>; + nand-on-flash-bbt; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + + mtd0@00000000 { + label = "phy3250-boot"; + reg = <0x00000000 0x00064000>; + read-only; + }; + + ... + + }; diff --git a/Documentation/devicetree/bindings/mtd/marvell,nand-controller.yaml b/Documentation/devicetree/bindings/mtd/marvell,nand-controller.yaml new file mode 100644 index 0000000000..1ecea848e8 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/marvell,nand-controller.yaml @@ -0,0 +1,227 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/marvell,nand-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell NAND Flash Controller (NFC) + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +properties: + compatible: + oneOf: + - items: + - const: marvell,armada-8k-nand-controller + - const: marvell,armada370-nand-controller + - enum: + - marvell,ac5-nand-controller + - marvell,armada370-nand-controller + - marvell,pxa3xx-nand-controller + - description: legacy bindings + deprecated: true + enum: + - marvell,armada-8k-nand + - marvell,armada370-nand + - marvell,pxa3xx-nand + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + description: + Shall reference the NAND controller clocks, the second one is + is only needed for the Armada 7K/8K SoCs + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: core + - const: reg + + dmas: + maxItems: 1 + + dma-names: + items: + - const: data + + marvell,system-controller: + $ref: /schemas/types.yaml#/definitions/phandle + description: Syscon node that handles NAND controller related registers + +patternProperties: + "^nand@[a-f0-9]$": + type: object + $ref: raw-nand-chip.yaml + + properties: + reg: + minimum: 0 + maximum: 3 + + nand-rb: + items: + - minimum: 0 + maximum: 1 + + nand-ecc-step-size: + const: 512 + + nand-ecc-strength: + enum: [1, 4, 8, 12, 16] + + nand-ecc-mode: + const: hw + + marvell,nand-keep-config: + $ref: /schemas/types.yaml#/definitions/flag + description: + Orders the driver not to take the timings from the core and + leaving them completely untouched. Bootloader timings will then + be used. + + marvell,nand-enable-arbiter: + $ref: /schemas/types.yaml#/definitions/flag + description: + To enable the arbiter, all boards blindly used it, + this bit was set by the bootloader for many boards and even if + it is marked reserved in several datasheets, it might be needed to set + it (otherwise it is harmless). + deprecated: true + + required: + - reg + - nand-rb + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + +allOf: + - $ref: nand-controller.yaml# + + - if: + properties: + compatible: + contains: + const: marvell,pxa3xx-nand-controller + then: + required: + - dmas + - dma-names + + - if: + properties: + compatible: + contains: + const: marvell,armada-8k-nand-controller + then: + properties: + clocks: + minItems: 2 + + clock-names: + minItems: 2 + + required: + - marvell,system-controller + + else: + properties: + clocks: + minItems: 1 + + clock-names: + minItems: 1 + + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + nand_controller: nand-controller@d0000 { + compatible = "marvell,armada370-nand-controller"; + reg = <0xd0000 0x54>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&coredivclk 0>; + + nand@0 { + reg = <0>; + label = "main-storage"; + nand-rb = <0>; + nand-ecc-mode = "hw"; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Rootfs"; + reg = <0x00000000 0x40000000>; + }; + }; + }; + }; + + - | + cp0_nand_controller: nand-controller@720000 { + compatible = "marvell,armada-8k-nand-controller", + "marvell,armada370-nand-controller"; + reg = <0x720000 0x54>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <115 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "core", "reg"; + clocks = <&cp0_clk 1 2>, + <&cp0_clk 1 17>; + marvell,system-controller = <&cp0_syscon0>; + + nand@0 { + reg = <0>; + label = "main-storage"; + nand-rb = <0>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <8>; + nand-ecc-step-size = <512>; + }; + }; + + - | + nand-controller@43100000 { + compatible = "marvell,pxa3xx-nand-controller"; + reg = <0x43100000 90>; + interrupts = <45>; + clocks = <&clks 1>; + clock-names = "core"; + dmas = <&pdma 97 3>; + dma-names = "data"; + #address-cells = <1>; + #size-cells = <0>; + nand@0 { + reg = <0>; + nand-rb = <0>; + nand-ecc-mode = "hw"; + marvell,nand-keep-config; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml b/Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml new file mode 100644 index 0000000000..ab503a33a2 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml @@ -0,0 +1,154 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/mediatek,mtk-nfc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek(MTK) SoCs raw NAND FLASH controller (NFC) + +maintainers: + - Xiangsheng Hou <xiangsheng.hou@mediatek.com> + +properties: + compatible: + enum: + - mediatek,mt2701-nfc + - mediatek,mt2712-nfc + - mediatek,mt7622-nfc + + reg: + items: + - description: Base physical address and size of NFI. + + interrupts: + items: + - description: NFI interrupt + + clocks: + items: + - description: clock used for the controller + - description: clock used for the pad + + clock-names: + items: + - const: nfi_clk + - const: pad_clk + + ecc-engine: + description: device-tree node of the required ECC engine. + $ref: /schemas/types.yaml#/definitions/phandle + +patternProperties: + "^nand@[a-f0-9]$": + $ref: raw-nand-chip.yaml# + unevaluatedProperties: false + properties: + reg: + maximum: 1 + nand-ecc-mode: + const: hw + +allOf: + - $ref: nand-controller.yaml# + + - if: + properties: + compatible: + contains: + const: mediatek,mt2701-nfc + then: + patternProperties: + "^nand@[a-f0-9]$": + properties: + nand-ecc-step-size: + enum: [ 512, 1024 ] + nand-ecc-strength: + enum: [4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, + 40, 44, 48, 52, 56, 60] + + - if: + properties: + compatible: + contains: + const: mediatek,mt2712-nfc + then: + patternProperties: + "^nand@[a-f0-9]$": + properties: + nand-ecc-step-size: + enum: [ 512, 1024 ] + nand-ecc-strength: + enum: [4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, + 40, 44, 48, 52, 56, 60, 68, 72, 80] + + - if: + properties: + compatible: + contains: + const: mediatek,mt7622-nfc + then: + patternProperties: + "^nand@[a-f0-9]$": + properties: + nand-ecc-step-size: + const: 512 + nand-ecc-strength: + enum: [4, 6, 8, 10, 12] + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - ecc-engine + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/mt2701-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + nand-controller@1100d000 { + compatible = "mediatek,mt2701-nfc"; + reg = <0 0x1100d000 0 0x1000>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_NFI>, + <&pericfg CLK_PERI_NFI_PAD>; + clock-names = "nfi_clk", "pad_clk"; + ecc-engine = <&bch>; + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + + nand-on-flash-bbt; + nand-ecc-mode = "hw"; + nand-ecc-step-size = <1024>; + nand-ecc-strength = <24>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + preloader@0 { + label = "pl"; + read-only; + reg = <0x0 0x400000>; + }; + android@400000 { + label = "android"; + reg = <0x400000 0x12c00000>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml new file mode 100644 index 0000000000..505baf1e88 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/mediatek,nand-ecc-engine.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek(MTK) SoCs NAND ECC engine + +maintainers: + - Xiangsheng Hou <xiangsheng.hou@mediatek.com> + +description: | + MTK NAND ECC engine can cowork with MTK raw NAND and SPI NAND controller. + +properties: + compatible: + enum: + - mediatek,mt2701-ecc + - mediatek,mt2712-ecc + - mediatek,mt7622-ecc + - mediatek,mt7986-ecc + + reg: + items: + - description: Base physical address and size of ECC. + + interrupts: + items: + - description: ECC interrupt + + clocks: + maxItems: 1 + + clock-names: + const: nfiecc_clk + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt2701-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + bch: ecc@1100e000 { + compatible = "mediatek,mt2701-ecc"; + reg = <0 0x1100e000 0 0x1000>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_NFI_ECC>; + clock-names = "nfiecc_clk"; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/microchip,mchp23k256.txt b/Documentation/devicetree/bindings/mtd/microchip,mchp23k256.txt new file mode 100644 index 0000000000..7328eb92a0 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/microchip,mchp23k256.txt @@ -0,0 +1,18 @@ +* MTD SPI driver for Microchip 23K256 (and similar) serial SRAM + +Required properties: +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. +- compatible : Must be one of "microchip,mchp23k256" or "microchip,mchp23lcv1024" +- reg : Chip-Select number +- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at + +Example: + + spi-sram@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "microchip,mchp23k256"; + reg = <0>; + spi-max-frequency = <20000000>; + }; diff --git a/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml b/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml new file mode 100644 index 0000000000..0ff32bd00b --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml @@ -0,0 +1,46 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/microchip,mchp48l640.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip 48l640 (and similar) serial EERAM + +maintainers: + - Heiko Schocher <hs@denx.de> + +description: | + The Microchip 48l640 is a 8KByte EERAM connected via SPI. + + datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/20006055B.pdf + +properties: + compatible: + items: + - const: microchip,48l640 + + reg: + maxItems: 1 + +required: + - compatible + - reg + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + eeram@0 { + compatible = "microchip,48l640"; + reg = <0>; + spi-max-frequency = <20000000>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.yaml b/Documentation/devicetree/bindings/mtd/mtd-physmap.yaml new file mode 100644 index 0000000000..18f6733408 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.yaml @@ -0,0 +1,225 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: CFI or JEDEC memory-mapped NOR flash, MTD-RAM (NVRAM...) + +maintainers: + - Rob Herring <robh@kernel.org> + +description: | + Flash chips (Memory Technology Devices) are often used for solid state + file systems on embedded devices. + +allOf: + - $ref: mtd.yaml# + - $ref: /schemas/memory-controllers/mc-peripheral-props.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - amd,s29gl01gp + - amd,s29gl032a + - amd,s29gl256n + - amd,s29gl512n + - arm,versatile-flash + - arm,vexpress-flash + - cortina,gemini-flash + - cypress,hyperflash + - ge,imp3a-firmware-mirror + - ge,imp3a-paged-flash + - gef,ppc9a-firmware-mirror + - gef,ppc9a-paged-flash + - gef,sbc310-firmware-mirror + - gef,sbc310-paged-flash + - gef,sbc610-firmware-mirror + - gef,sbc610-paged-flash + - intel,28f128j3 + - intel,dt28f160 + - intel,ixp4xx-flash + - intel,JS28F128 + - intel,JS28F640 + - intel,PC28F640P30T85 + - numonyx,js28f00a + - numonyx,js28f128 + - sst,sst39vf320 + - xlnx,xps-mch-emc-2.00.a + - enum: + - cfi-flash + - jedec-flash + - items: + - enum: + - cypress,cy7c1019dv33-10zsxi + - arm,vexpress-psram + - const: mtd-ram + - enum: + - cfi-flash + - jedec-flash + - mtd-ram + - mtd-rom + + reg: + description: | + It's possible to (optionally) define multiple "reg" tuples so that + non-identical chips can be described in one node. + minItems: 1 + maxItems: 8 + + bank-width: + description: Width (in bytes) of the bank. Equal to the device width times + the number of interleaved chips. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 1, 2, 4 ] + + device-width: + description: + Width of a single mtd chip. If omitted, assumed to be equal to 'bank-width'. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 1, 2 ] + + no-unaligned-direct-access: + type: boolean + description: | + Disables the default direct mapping of the flash. + + On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause problems + with JFFS2 usage, as the local bus (LPB) doesn't support unaligned + accesses as implemented in the JFFS2 code via memcpy(). By defining + "no-unaligned-direct-access", the flash will not be exposed directly to + the MTD users (e.g. JFFS2) any more. + + linux,mtd-name: + description: + Allows specifying the mtd name for retro capability with physmap-flash + drivers as boot loader pass the mtd partition via the old device name + physmap-flash. + $ref: /schemas/types.yaml#/definitions/string + + use-advanced-sector-protection: + type: boolean + description: | + Enables support for the advanced sector protection (Spansion: PPB - + Persistent Protection Bits) locking. + + erase-size: + description: The chip's physical erase block size in bytes. + $ref: /schemas/types.yaml#/definitions/uint32 + + addr-gpios: + description: + List of GPIO descriptors that will be used to address the MSBs address + lines. The order goes from LSB to MSB. + minItems: 1 + maxItems: 8 + + '#address-cells': + const: 1 + + '#size-cells': + const: 1 + + big-endian: true + little-endian: true + +required: + - compatible + - reg + +if: + properties: + compatible: + contains: + const: cortina,gemini-flash +then: + properties: + syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to the syscon controller + required: + - syscon + +# FIXME: A parent bus may define timing properties +additionalProperties: true + +examples: + - | + + flash@ff000000 { + compatible = "cfi-flash"; + reg = <0xff000000 0x01000000>; + bank-width = <4>; + device-width = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0xff000000 0x01000000>; + + fs@0 { + label = "fs"; + reg = <0 0xf80000>; + }; + firmware@f80000 { + label = "firmware"; + reg = <0xf80000 0x80000>; + read-only; + }; + }; + + - | + /* An example with multiple "reg" tuples */ + + flash@0 { + compatible = "intel,PC28F640P30T85", "cfi-flash"; + reg = <0x00000000 0x02000000>, + <0x02000000 0x02000000>; + bank-width = <2>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x04000000>; + + partition@0 { + label = "test-part1"; + reg = <0 0x04000000>; + }; + }; + + - | + /* An example using SRAM */ + bus { + #address-cells = <2>; + #size-cells = <1>; + + sram@2,0 { + compatible = "mtd-ram"; + reg = <2 0 0x00200000>; + bank-width = <2>; + }; + }; + + - | + /* An example using addr-gpios */ + #include <dt-bindings/gpio/gpio.h> + + flash@20000000 { + compatible = "cfi-flash"; + reg = <0x20000000 0x02000000>; + bank-width = <2>; + addr-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x00000000 0x02000000>, + <1 0x02000000 0x02000000>; + + partition@0 { + label = "test-part1"; + reg = <0 0x04000000>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/mtd/mtd.yaml b/Documentation/devicetree/bindings/mtd/mtd.yaml new file mode 100644 index 0000000000..b82ca03e96 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mtd.yaml @@ -0,0 +1,110 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/mtd.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MTD (Memory Technology Device) + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + - Richard Weinberger <richard@nod.at> + +properties: + $nodename: + pattern: "^(flash|.*sram|nand)(@.*)?$" + + label: + description: + User-defined MTD device name. Can be used to assign user friendly + names to MTD devices (instead of the flash model or flash controller + based name) in order to ease flash device identification and/or + describe what they are used for. + + '#address-cells': + deprecated: true + + '#size-cells': + deprecated: true + + partitions: + $ref: /schemas/mtd/partitions/partitions.yaml + + required: + - compatible + +patternProperties: + "@[0-9a-f]+$": + $ref: partitions/partition.yaml + deprecated: true + + "^partition@[0-9a-f]+": + $ref: partitions/partition.yaml + deprecated: true + + "^otp(-[0-9]+)?$": + $ref: ../nvmem/nvmem.yaml# + unevaluatedProperties: false + + description: | + An OTP memory region. Some flashes provide a one-time-programmable + memory whose content can either be programmed by a user or is already + pre-programmed by the factory. Some flashes might provide both. + + properties: + compatible: + enum: + - user-otp + - factory-otp + + required: + - compatible + +# This is a generic file other binding inherit from +additionalProperties: true + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + flash@0 { + reg = <0>; + compatible = "jedec,spi-nor"; + label = "System-firmware"; + }; + }; + + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + flash@0 { + reg = <0>; + compatible = "jedec,spi-nor"; + + otp-1 { + compatible = "factory-otp"; + #address-cells = <1>; + #size-cells = <1>; + + electronic-serial-number@0 { + reg = <0 8>; + }; + }; + + otp-2 { + compatible = "user-otp"; + #address-cells = <1>; + #size-cells = <1>; + + mac-address@0 { + reg = <0 6>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/mtd/mxc-nand.yaml b/Documentation/devicetree/bindings/mtd/mxc-nand.yaml new file mode 100644 index 0000000000..cf4198e43d --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mxc-nand.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/mxc-nand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale's mxc_nand + +maintainers: + - Uwe Kleine-König <u.kleine-koenig@pengutronix.de> + +allOf: + - $ref: nand-controller.yaml + +properties: + compatible: + const: fsl,imx27-nand + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + nand-controller@d8000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx27-nand"; + reg = <0xd8000000 0x1000>; + interrupts = <29>; + }; diff --git a/Documentation/devicetree/bindings/mtd/mxic-nand.txt b/Documentation/devicetree/bindings/mtd/mxic-nand.txt new file mode 100644 index 0000000000..46c55295a3 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mxic-nand.txt @@ -0,0 +1,36 @@ +Macronix Raw NAND Controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible: should be "mxic,multi-itfc-v009-nand-controller" +- reg: should contain 1 entry for the registers +- #address-cells: should be set to 1 +- #size-cells: should be set to 0 +- interrupts: interrupt line connected to this raw NAND controller +- clock-names: should contain "ps", "send" and "send_dly" +- clocks: should contain 3 phandles for the "ps", "send" and + "send_dly" clocks + +Children nodes: +- children nodes represent the available NAND chips. + +See Documentation/devicetree/bindings/mtd/nand-controller.yaml +for more details on generic bindings. + +Example: + + nand: nand-controller@43c30000 { + compatible = "mxic,multi-itfc-v009-nand-controller"; + reg = <0x43c30000 0x10000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 0x1d IRQ_TYPE_EDGE_RISING>; + clocks = <&clkwizard 0>, <&clkwizard 1>, <&clkc 15>; + clock-names = "send", "send_dly", "ps"; + + nand@0 { + reg = <0>; + nand-ecc-mode = "soft"; + nand-ecc-algo = "bch"; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/mxicy,nand-ecc-engine.yaml b/Documentation/devicetree/bindings/mtd/mxicy,nand-ecc-engine.yaml new file mode 100644 index 0000000000..f92e7234de --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mxicy,nand-ecc-engine.yaml @@ -0,0 +1,77 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/mxicy,nand-ecc-engine.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Macronix NAND ECC engine + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +properties: + compatible: + const: mxicy,nand-ecc-engine-rev3 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + /* External configuration */ + spi_controller0: spi@43c30000 { + compatible = "mxicy,mx25f0a-spi"; + reg = <0x43c30000 0x10000>, <0xa0000000 0x4000000>; + reg-names = "regs", "dirmap"; + clocks = <&clkwizard 0>, <&clkwizard 1>, <&clkc 15>; + clock-names = "send_clk", "send_dly_clk", "ps_clk"; + #address-cells = <1>; + #size-cells = <0>; + + flash@0 { + compatible = "spi-nand"; + reg = <0>; + nand-ecc-engine = <&ecc_engine0>; + }; + }; + + ecc_engine0: ecc@43c40000 { + compatible = "mxicy,nand-ecc-engine-rev3"; + reg = <0x43c40000 0x10000>; + }; + + - | + /* Pipelined configuration */ + spi_controller1: spi@43c30000 { + compatible = "mxicy,mx25f0a-spi"; + reg = <0x43c30000 0x10000>, <0xa0000000 0x4000000>; + reg-names = "regs", "dirmap"; + clocks = <&clkwizard 0>, <&clkwizard 1>, <&clkc 15>; + clock-names = "send_clk", "send_dly_clk", "ps_clk"; + #address-cells = <1>; + #size-cells = <0>; + nand-ecc-engine = <&ecc_engine1>; + + flash@0 { + compatible = "spi-nand"; + reg = <0>; + nand-ecc-engine = <&spi_controller1>; + }; + }; + + ecc_engine1: ecc@43c40000 { + compatible = "mxicy,nand-ecc-engine-rev3"; + reg = <0x43c40000 0x10000>; + }; diff --git a/Documentation/devicetree/bindings/mtd/nand-chip.yaml b/Documentation/devicetree/bindings/mtd/nand-chip.yaml new file mode 100644 index 0000000000..609d4a4ddd --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/nand-chip.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/nand-chip.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NAND Chip Common Properties + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +allOf: + - $ref: mtd.yaml# + +description: | + This file covers the generic description of a NAND chip. It implies that the + bus interface should not be taken into account: both raw NAND devices and + SPI-NAND devices are concerned by this description. + +properties: + reg: + description: + Contains the chip-select IDs. + + nand-ecc-engine: + description: | + A phandle on the hardware ECC engine if any. There are + basically three possibilities: + 1/ The ECC engine is part of the NAND controller, in this + case the phandle should reference the parent node. + 2/ The ECC engine is part of the NAND part (on-die), in this + case the phandle should reference the node itself. + 3/ The ECC engine is external, in this case the phandle should + reference the specific ECC engine node. + $ref: /schemas/types.yaml#/definitions/phandle + + nand-use-soft-ecc-engine: + description: Use a software ECC engine. + type: boolean + + nand-no-ecc-engine: + description: Do not use any ECC correction. + type: boolean + + nand-ecc-algo: + description: + Desired ECC algorithm. + $ref: /schemas/types.yaml#/definitions/string + enum: [hamming, bch, rs] + + nand-ecc-strength: + description: + Maximum number of bits that can be corrected per ECC step. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + + nand-ecc-step-size: + description: + Number of data bytes covered by a single ECC step. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + + secure-regions: + description: + Regions in the NAND chip which are protected using a secure element + like Trustzone. This property contains the start address and size of + the secure regions present. + $ref: /schemas/types.yaml#/definitions/uint64-matrix + +required: + - reg + +# This file can be referenced by more specific devices (like spi-nands) +additionalProperties: true diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml new file mode 100644 index 0000000000..28167c0cf2 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/nand-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NAND Controller Common Properties + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + - Richard Weinberger <richard@nod.at> + +description: | + The NAND controller should be represented with its own DT node, and + all NAND chips attached to this controller should be defined as + children nodes of the NAND controller. This representation should be + enforced even for simple controllers supporting only one chip. + +properties: + $nodename: + pattern: "^nand-controller(@.*)?" + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + ranges: true + + cs-gpios: + description: + Array of chip-select available to the controller. The first + entries are a 1:1 mapping of the available chip-select on the + NAND controller (even if they are not used). As many additional + chip-select as needed may follow and should be phandles of GPIO + lines. 'reg' entries of the NAND chip subnodes become indexes of + this array when this property is present. + minItems: 1 + maxItems: 8 + +patternProperties: + "^nand@[a-f0-9]$": + type: object + $ref: raw-nand-chip.yaml# + +required: + - "#address-cells" + - "#size-cells" + +# This is a generic file other binding inherit from and extend +additionalProperties: true + +examples: + - | + nand-controller { + #address-cells = <1>; + #size-cells = <0>; + cs-gpios = <0>, <&gpioA 1>; /* A single native CS is available */ + + /* controller specific properties */ + + nand@0 { + reg = <0>; /* Native CS */ + /* NAND chip specific properties */ + }; + + nand@1 { + reg = <1>; /* GPIO CS */ + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/nand-macronix.txt b/Documentation/devicetree/bindings/mtd/nand-macronix.txt new file mode 100644 index 0000000000..ffab28a2c4 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/nand-macronix.txt @@ -0,0 +1,27 @@ +Macronix NANDs Device Tree Bindings +----------------------------------- + +Macronix NANDs support randomizer operation for scrambling user data, +which can be enabled with a SET_FEATURE. The penalty when using the +randomizer are subpage accesses prohibited and more time period needed +for program operation, i.e., tPROG 300us to 340us (randomizer enabled). +Enabling the randomizer is a one time persistent and non reversible +operation. + +For more high-reliability concern, if subpage write is not available +with hardware ECC and not enabled at UBI level, then enabling the +randomizer is recommended by default by adding a new specific property +in children nodes. + +Required NAND chip properties in children mode: +- randomizer enable: should be "mxic,enable-randomizer-otp" + +Example: + + nand: nand-controller@unit-address { + + nand@0 { + reg = <0>; + mxic,enable-randomizer-otp; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt b/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt new file mode 100644 index 0000000000..e737e5beb7 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt @@ -0,0 +1,64 @@ +NVIDIA Tegra NAND Flash controller + +Required properties: +- compatible: Must be one of: + - "nvidia,tegra20-nand" +- reg: MMIO address range +- interrupts: interrupt output of the NFC controller +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - nand +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - nand + +Optional children nodes: +Individual NAND chips are children of the NAND controller node. Currently +only one NAND chip supported. + +Required children node properties: +- reg: An integer ranging from 1 to 6 representing the CS line to use. + +Optional children node properties: +- nand-ecc-mode: String, operation mode of the NAND ecc mode. Currently only + "hw" is supported. +- nand-ecc-algo: string, algorithm of NAND ECC. + Supported values with "hw" ECC mode are: "rs", "bch". +- nand-bus-width : See nand-controller.yaml +- nand-on-flash-bbt: See nand-controller.yaml +- nand-ecc-strength: integer representing the number of bits to correct + per ECC step (always 512). Supported strength using HW ECC + modes are: + - RS: 4, 6, 8 + - BCH: 4, 8, 14, 16 +- nand-ecc-maximize: See nand-controller.yaml +- nand-is-boot-medium: Makes sure only ECC strengths supported by the boot ROM + are chosen. +- wp-gpios: GPIO specifier for the write protect pin. + +Optional child node of NAND chip nodes: +Partitions: see partition.txt + + Example: + nand-controller@70008000 { + compatible = "nvidia,tegra20-nand"; + reg = <0x70008000 0x100>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA20_CLK_NDFLASH>; + clock-names = "nand"; + resets = <&tegra_car 13>; + reset-names = "nand"; + + nand@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + nand-bus-width = <8>; + nand-on-flash-bbt; + nand-ecc-algo = "bch"; + nand-ecc-strength = <8>; + wp-gpios = <&gpio TEGRA_GPIO(S, 0) GPIO_ACTIVE_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/nxp-spifi.txt b/Documentation/devicetree/bindings/mtd/nxp-spifi.txt new file mode 100644 index 0000000000..f8b6b25065 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/nxp-spifi.txt @@ -0,0 +1,58 @@ +* NXP SPI Flash Interface (SPIFI) + +NXP SPIFI is a specialized SPI interface for serial Flash devices. +It supports one Flash device with 1-, 2- and 4-bits width in SPI +mode 0 or 3. The controller operates in either command or memory +mode. In memory mode the Flash is accessible from the CPU as +normal memory. + +Required properties: + - compatible : Should be "nxp,lpc1773-spifi" + - reg : the first contains the register location and length, + the second contains the memory mapping address and length + - reg-names: Should contain the reg names "spifi" and "flash" + - interrupts : Should contain the interrupt for the device + - clocks : The clocks needed by the SPIFI controller + - clock-names : Should contain the clock names "spifi" and "reg" + +Optional properties: + - resets : phandle + reset specifier + +The SPI Flash must be a child of the SPIFI node and must have a +compatible property as specified in bindings/mtd/jedec,spi-nor.txt + +Optionally it can also contain the following properties. + - spi-cpol : Controller only supports mode 0 and 3 so either + both spi-cpol and spi-cpha should be present or + none of them + - spi-cpha : See above + - spi-rx-bus-width : Used to select how many pins that are used + for input on the controller + +See bindings/spi/spi-bus.txt for more information. + +Example: +spifi: spifi@40003000 { + compatible = "nxp,lpc1773-spifi"; + reg = <0x40003000 0x1000>, <0x14000000 0x4000000>; + reg-names = "spifi", "flash"; + interrupts = <30>; + clocks = <&ccu1 CLK_SPIFI>, <&ccu1 CLK_CPU_SPIFI>; + clock-names = "spifi", "reg"; + resets = <&rgu 53>; + + flash@0 { + compatible = "jedec,spi-nor"; + spi-cpol; + spi-cpha; + spi-rx-bus-width = <4>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "data"; + reg = <0 0x200000>; + }; + }; +}; + diff --git a/Documentation/devicetree/bindings/mtd/orion-nand.txt b/Documentation/devicetree/bindings/mtd/orion-nand.txt new file mode 100644 index 0000000000..2d6ab660e6 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/orion-nand.txt @@ -0,0 +1,50 @@ +NAND support for Marvell Orion SoC platforms + +Required properties: +- compatible : "marvell,orion-nand". +- reg : Base physical address of the NAND and length of memory mapped + region + +Optional properties: +- cle : Address line number connected to CLE. Default is 0 +- ale : Address line number connected to ALE. Default is 1 +- bank-width : Width in bytes of the device. Default is 1 +- chip-delay : Chip dependent delay for transferring data from array to read + registers in usecs + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + +nand@f4000000 { + #address-cells = <1>; + #size-cells = <1>; + cle = <0>; + ale = <1>; + bank-width = <1>; + chip-delay = <25>; + compatible = "marvell,orion-nand"; + reg = <0xf4000000 0x400>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + partition@100000 { + label = "uImage"; + reg = <0x0100000 0x200000>; + }; + + partition@300000 { + label = "dtb"; + reg = <0x0300000 0x100000>; + }; + + partition@400000 { + label = "root"; + reg = <0x0400000 0x7d00000>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.yaml b/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.yaml new file mode 100644 index 0000000000..97618847ee --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.yaml @@ -0,0 +1,30 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/arm,arm-firmware-suite.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM Firmware Suite (AFS) Partitions + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +select: false + +description: | + The ARM Firmware Suite is a flash partitioning system found on the + ARM reference designs: Integrator AP, Integrator CP, Versatile AB, + Versatile PB, the RealView family, Versatile Express and Juno. + +properties: + compatible: + const: arm,arm-firmware-suite + +additionalProperties: false + +examples: + - | + partitions { + compatible = "arm,arm-firmware-suite"; + }; +... diff --git a/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm4908-partitions.yaml b/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm4908-partitions.yaml new file mode 100644 index 0000000000..94f0742b37 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm4908-partitions.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/brcm,bcm4908-partitions.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM4908 partitioning + +description: | + Broadcom BCM4908 CFE bootloader supports two firmware partitions. One is used + for regular booting, the other is treated as fallback. + + This binding allows defining all fixed partitions and marking those containing + firmware. System can use that information e.g. for booting or flashing + purposes. + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +select: false + +properties: + compatible: + const: brcm,bcm4908-partitions + + "#address-cells": + enum: [ 1, 2 ] + + "#size-cells": + enum: [ 1, 2 ] + +patternProperties: + "^partition@[0-9a-f]+$": + $ref: partition.yaml# + properties: + compatible: + const: brcm,bcm4908-firmware + unevaluatedProperties: false + +required: + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + partitions { + compatible = "brcm,bcm4908-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "cferom"; + reg = <0x0 0x100000>; + }; + + partition@100000 { + compatible = "brcm,bcm4908-firmware"; + reg = <0x100000 0xf00000>; + }; + + partition@1000000 { + compatible = "brcm,bcm4908-firmware"; + reg = <0x1000000 0xf00000>; + }; + + partition@1f00000 { + label = "calibration"; + reg = <0x1f00000 0x100000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm947xx-cfe-partitions.yaml b/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm947xx-cfe-partitions.yaml new file mode 100644 index 0000000000..939e7b50db --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm947xx-cfe-partitions.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/brcm,bcm947xx-cfe-partitions.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM47xx Partitions + +description: | + Broadcom is one of hardware manufacturers providing SoCs (BCM47xx) used in + home routers. Their BCM947xx boards using CFE bootloader have several + partitions without any on-flash partition table. On some devices their sizes + and/or meanings can also vary so fixed partitioning can't be used. + + Discovering partitions on these devices is possible thanks to having a special + header and/or magic signature at the beginning of each of them. They are also + block aligned which is important for determinig a size. + + Most of partitions use ASCII text based magic for determining a type. More + complex partitions (like TRX with its HDR0 magic) may include extra header + containing some details, including a length. + + A list of supported partitions includes: + 1) Bootloader with Broadcom's CFE (Common Firmware Environment) + 2) NVRAM with configuration/calibration data + 3) Device manufacturer's data with some default values (e.g. SSIDs) + 4) TRX firmware container which can hold up to 4 subpartitions + 5) Backup TRX firmware used after failed upgrade + + As mentioned earlier, role of some partitions may depend on extra + configuration. For example both: main firmware and backup firmware use the + same TRX format with the same header. To distinguish currently used firmware a + CFE's environment variable "bootpartition" is used. + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +select: false + +properties: + compatible: + const: brcm,bcm947xx-cfe-partitions + +additionalProperties: false + +examples: + - | + partitions { + compatible = "brcm,bcm947xx-cfe-partitions"; + }; diff --git a/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm963xx-cfe-nor-partitions.txt b/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm963xx-cfe-nor-partitions.txt new file mode 100644 index 0000000000..9f630e95f1 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm963xx-cfe-nor-partitions.txt @@ -0,0 +1,24 @@ +Broadcom BCM963XX CFE Loader NOR Flash Partitions +================================================= + +Most Broadcom BCM63XX SoC based devices follow the Broadcom reference layout for +NOR. The first erase block used for the CFE bootloader, the last for an +NVRAM partition, and the remainder in-between for one to two firmware partitions +at fixed offsets. A valid firmware partition is identified by the ImageTag +header found at beginning of the second erase block, containing the rootfs and +kernel offsets and sizes within the firmware partition. + +Required properties: +- compatible : must be "brcm,bcm963xx-cfe-nor-partitions" + +Example: + +flash@1fc00000 { + compatible = "cfi-flash"; + reg = <0x1fc00000 0x400000>; + bank-width = <2>; + + partitions { + compatible = "brcm,bcm963xx-cfe-nor-partitions"; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm963xx-imagetag.txt b/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm963xx-imagetag.txt new file mode 100644 index 0000000000..f8b7418ed8 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm963xx-imagetag.txt @@ -0,0 +1,45 @@ +Broadcom BCM963XX ImageTag Partition Container +============================================== + +Some Broadcom BCM63XX SoC based devices contain additional, non discoverable +partitions or non standard bootloader partition sizes. For these a mixed layout +needs to be used with an explicit firmware partition. + +The BCM963XX ImageTag is a simple firmware header describing the offsets and +sizes of the rootfs and kernel parts contained in the firmware. + +Required properties: +- compatible : must be "brcm,bcm963xx-imagetag" + +Example: + +flash@1e000000 { + compatible = "cfi-flash"; + reg = <0x1e000000 0x2000000>; + bank-width = <2>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + cfe@0 { + reg = <0x0 0x10000>; + read-only; + }; + + firmware@10000 { + reg = <0x10000 0x7d0000>; + compatible = "brcm,bcm963xx-imagetag"; + }; + + caldata@7e0000 { + reg = <0x7e0000 0x10000>; + read-only; + }; + + nvram@7f0000 { + reg = <0x7f0000 0x10000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/partitions/brcm,trx.txt b/Documentation/devicetree/bindings/mtd/partitions/brcm,trx.txt new file mode 100644 index 0000000000..c2175d3c82 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/brcm,trx.txt @@ -0,0 +1,42 @@ +Broadcom TRX Container Partition +================================ + +TRX is Broadcom's official firmware format for the BCM947xx boards. It's used by +most of the vendors building devices based on Broadcom's BCM47xx SoCs and is +supported by the CFE bootloader. + +Design of the TRX format is very minimalistic. Its header contains +identification fields, CRC32 checksum and the locations of embedded partitions. +Its purpose is to store a few partitions in a format that can be distributed as +a standalone file and written in a flash memory. + +Container can hold up to 4 partitions. The first partition has to contain a +device executable binary (e.g. a kernel) as it's what the CFE bootloader starts +executing. Other partitions can be used for operating system purposes. This is +useful for systems that keep kernel and rootfs separated. + +TRX doesn't enforce any strict partition boundaries or size limits. All +partitions have to be less than the 4GiB max size limit. + +There are two existing/known TRX variants: +1) v1 which contains 3 partitions +2) v2 which contains 4 partitions + +There aren't separated compatible bindings for them as version can be trivialy +detected by a software parsing TRX header. + +Required properties: +- compatible : (required) must be "brcm,trx" + +Optional properties: + +- brcm,trx-magic: TRX magic, if it is different from the default magic + 0x30524448 as a u32. + +Example: + +flash@0 { + partitions { + compatible = "brcm,trx"; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/partitions/fixed-partitions.yaml b/Documentation/devicetree/bindings/mtd/partitions/fixed-partitions.yaml new file mode 100644 index 0000000000..331e564f29 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/fixed-partitions.yaml @@ -0,0 +1,166 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/fixed-partitions.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Fixed partitions + +description: | + This binding can be used on platforms which have strong conventions about + which portions of a flash are used for what purposes, but which don't use an + on-flash partition table such as RedBoot. + + The partition table should be a node named "partitions". Partitions are then + defined as subnodes. + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +properties: + compatible: + oneOf: + - const: fixed-partitions + - items: + - const: sercomm,sc-partitions + - const: fixed-partitions + + "#address-cells": true + + "#size-cells": true + +patternProperties: + "@[0-9a-f]+$": + $ref: partition.yaml# + + properties: + sercomm,scpart-id: + description: Partition id in Sercomm partition map. Mtd parser + uses this id to find a record in the partition map containing + offset and size of the current partition. The values from + partition map overrides partition offset and size defined in + reg property of the dts. Frequently these values are the same, + but may differ if device has bad eraseblocks on a flash. + $ref: /schemas/types.yaml#/definitions/uint32 + +required: + - "#address-cells" + - "#size-cells" + +additionalProperties: true + +examples: + - | + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + uimage@100000 { + reg = <0x0100000 0x200000>; + }; + }; + + - | + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <2>; + + /* a 4 GiB partition */ + partition@0 { + label = "filesystem"; + reg = <0x00000000 0x1 0x00000000>; + linux,rootfs; + }; + }; + + - | + partitions { + compatible = "fixed-partitions"; + #address-cells = <2>; + #size-cells = <2>; + + /* an 8 GiB partition */ + partition@0 { + label = "filesystem #1"; + reg = <0x0 0x00000000 0x2 0x00000000>; + }; + + /* a 4 GiB partition */ + partition@200000000 { + label = "filesystem #2"; + reg = <0x2 0x00000000 0x1 0x00000000>; + }; + }; + + - | + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bootloader"; + reg = <0x000000 0x100000>; + read-only; + }; + + firmware@100000 { + compatible = "brcm,trx"; + label = "firmware"; + reg = <0x100000 0xe00000>; + }; + + calibration@f00000 { + compatible = "fixed-partitions"; + label = "calibration"; + reg = <0xf00000 0x100000>; + ranges = <0 0xf00000 0x100000>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "wifi0"; + reg = <0x000000 0x080000>; + }; + + partition@80000 { + label = "wifi1"; + reg = <0x080000 0x080000>; + }; + }; + }; + + - | + partitions { + compatible = "sercomm,sc-partitions", "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x100000>; + sercomm,scpart-id = <0>; + read-only; + }; + + partition@100000 { + label = "dynamic partition map"; + reg = <0x100000 0x100000>; + sercomm,scpart-id = <1>; + }; + + partition@200000 { + label = "Factory"; + reg = <0x200000 0x100000>; + sercomm,scpart-id = <2>; + read-only; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/partitions/linksys,ns-partitions.yaml b/Documentation/devicetree/bindings/mtd/partitions/linksys,ns-partitions.yaml new file mode 100644 index 0000000000..c5fa78ff71 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/linksys,ns-partitions.yaml @@ -0,0 +1,76 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/linksys,ns-partitions.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Linksys Northstar partitioning + +description: | + Linksys devices based on Broadcom Northstar architecture often use two + firmware partitions. One is used for regular booting, the other is treated as + fallback. + + This binding allows defining all fixed partitions and marking those containing + firmware. System can use that information e.g. for booting or flashing + purposes. + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +select: false + +properties: + compatible: + const: linksys,ns-partitions + + "#address-cells": + enum: [ 1, 2 ] + + "#size-cells": + enum: [ 1, 2 ] + +patternProperties: + "^partition@[0-9a-f]+$": + $ref: partition.yaml# + properties: + compatible: + items: + - const: linksys,ns-firmware + - const: brcm,trx + unevaluatedProperties: false + +required: + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + partitions { + compatible = "linksys,ns-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "nvram"; + reg = <0x100000 0x100000>; + }; + + partition@200000 { + compatible = "linksys,ns-firmware", "brcm,trx"; + reg = <0x200000 0xf00000>; + }; + + partition@1100000 { + compatible = "linksys,ns-firmware", "brcm,trx"; + reg = <0x1100000 0xf00000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/partitions/nvmem-cells.yaml b/Documentation/devicetree/bindings/mtd/partitions/nvmem-cells.yaml new file mode 100644 index 0000000000..5474d63268 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/nvmem-cells.yaml @@ -0,0 +1,99 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/nvmem-cells.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Nvmem cells + +description: | + Any partition containing the compatible "nvmem-cells" will register as a + nvmem provider. + Each direct subnodes represents a nvmem cell following the nvmem binding. + Nvmem binding to declare nvmem-cells can be found in: + Documentation/devicetree/bindings/nvmem/nvmem.yaml + +maintainers: + - Ansuel Smith <ansuelsmth@gmail.com> + +allOf: + - $ref: /schemas/mtd/partitions/partition.yaml# + - $ref: /schemas/nvmem/nvmem.yaml# + +properties: + compatible: + const: nvmem-cells + +required: + - compatible + +unevaluatedProperties: false + +examples: + - | + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + /* ... */ + + }; + art: art@1200000 { + compatible = "nvmem-cells"; + reg = <0x1200000 0x0140000>; + label = "art"; + read-only; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_gmac1: macaddr_gmac1@0 { + reg = <0x0 0x6>; + }; + + macaddr_gmac2: macaddr_gmac2@6 { + reg = <0x6 0x6>; + }; + + pre_cal_24g: pre_cal_24g@1000 { + reg = <0x1000 0x2f20>; + }; + + pre_cal_5g: pre_cal_5g@5000{ + reg = <0x5000 0x2f20>; + }; + }; + - | + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bootloader"; + reg = <0x000000 0x100000>; + read-only; + }; + + firmware@100000 { + compatible = "brcm,trx"; + label = "firmware"; + reg = <0x100000 0xe00000>; + }; + + calibration@f00000 { + compatible = "nvmem-cells"; + label = "calibration"; + reg = <0xf00000 0x100000>; + #address-cells = <1>; + #size-cells = <1>; + + wifi0@0 { + reg = <0x000000 0x080000>; + }; + + wifi1@80000 { + reg = <0x080000 0x080000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/partitions/partition.yaml b/Documentation/devicetree/bindings/mtd/partitions/partition.yaml new file mode 100644 index 0000000000..1ebe9e2347 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/partition.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/partition.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Partition + +description: | + This binding describes a single flash partition. Each partition must have its + relative offset and size specified. Depending on partition function extra + properties can be used. + + A partition may be dynamically allocated by a specific parser at runtime. + In this specific case, a specific suffix is required to the node name. + Everything after 'partition-' will be used as the partition name to compare + with the one dynamically allocated by the specific parser. + If the partition contains invalid char a label can be provided that will + be used instead of the node name to make the comparison. + This is used to assign an OF node to the dynamiccally allocated partition + so that subsystem like NVMEM can provide an OF node and declare NVMEM cells. + The OF node will be assigned only if the partition label declared match the + one assigned by the parser at runtime. + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +properties: + reg: + description: partition's offset and size within the flash + maxItems: 1 + + label: + description: The label / name for this partition. If omitted, the label + is taken from the node name (excluding the unit address). + + read-only: + description: This parameter, if present, is a hint that this partition + should only be mounted read-only. This is usually used for flash + partitions containing early-boot firmware images or data which should + not be clobbered. + type: boolean + + lock: + description: Do not unlock the partition at initialization time (not + supported on all devices) + type: boolean + + slc-mode: + description: This parameter, if present, allows one to emulate SLC mode + on a partition attached to an MLC NAND thus making this partition + immune to paired-pages corruptions + type: boolean + + linux,rootfs: + description: Marks partition that contains root filesystem to mount and boot + user space from + type: boolean + +if: + not: + required: [ reg ] +then: + properties: + $nodename: + pattern: '^partition-.*$' + +# This is a generic file other binding inherit from and extend +additionalProperties: true diff --git a/Documentation/devicetree/bindings/mtd/partitions/partitions.yaml b/Documentation/devicetree/bindings/mtd/partitions/partitions.yaml new file mode 100644 index 0000000000..1dda2c8074 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/partitions.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/partitions.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Partitions + +description: | + This binding is generic and describes the content of the partitions container + node. All partition parsers must be referenced here. + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +oneOf: + - $ref: arm,arm-firmware-suite.yaml + - $ref: brcm,bcm4908-partitions.yaml + - $ref: brcm,bcm947xx-cfe-partitions.yaml + - $ref: fixed-partitions.yaml + - $ref: linksys,ns-partitions.yaml + - $ref: qcom,smem-part.yaml + - $ref: redboot-fis.yaml + - $ref: tplink,safeloader-partitions.yaml + +properties: + compatible: true + + '#address-cells': + enum: [1, 2] + + '#size-cells': + enum: [1, 2] + +patternProperties: + "^partition(-.+|@[0-9a-f]+)$": + $ref: partition.yaml + +required: + - compatible + +unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/mtd/partitions/qcom,smem-part.yaml b/Documentation/devicetree/bindings/mtd/partitions/qcom,smem-part.yaml new file mode 100644 index 0000000000..1c2b4e780c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/qcom,smem-part.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/qcom,smem-part.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SMEM NAND flash partition parser + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +description: | + The Qualcomm SoCs supporting the NAND controller interface features a Shared + Memory (SMEM) based partition table scheme. The maximum partitions supported + varies between partition table revisions. V3 supports maximum 16 partitions + and V4 supports 48 partitions. + +select: false + +properties: + compatible: + const: qcom,smem-part + +patternProperties: + "^partition-[0-9a-z]+$": + $ref: nvmem-cells.yaml + +required: + - compatible + +additionalProperties: false + +examples: + - | + flash { + partitions { + compatible = "qcom,smem-part"; + }; + }; + + - | + /* Example declaring dynamic partition */ + flash { + partitions { + compatible = "qcom,smem-part"; + + partition-art { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + label = "0:art"; + + macaddr_art_0: macaddr@0 { + reg = <0x0 0x6>; + }; + + macaddr_art_6: macaddr@6 { + reg = <0x6 0x6>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/partitions/redboot-fis.yaml b/Documentation/devicetree/bindings/mtd/partitions/redboot-fis.yaml new file mode 100644 index 0000000000..ba7445cd69 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/redboot-fis.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/redboot-fis.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RedBoot FLASH Image System (FIS) Partitions + +description: The FLASH Image System (FIS) directory is a flash description + format closely associated with the RedBoot boot loader. + It uses one single flash eraseblock in the flash to store an index of + all images in the flash. + This block size will vary depending on flash but is typically + 32 KB in size. + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +select: false + +properties: + compatible: + const: redboot-fis + + fis-index-block: + $ref: /schemas/types.yaml#/definitions/uint32 + description: a index to the eraseblock containing the FIS directory on this + device. On a flash memory with 32KB eraseblocks, 0 means the first + eraseblock at 0x00000000, 1 means the second eraseblock at 0x00008000 and so on. + + '#address-cells': false + + '#size-cells': false + +required: + - compatible + - fis-index-block + +additionalProperties: false + +examples: + - | + flash { + partitions { + compatible = "redboot-fis"; + fis-index-block = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/partitions/seama.yaml b/Documentation/devicetree/bindings/mtd/partitions/seama.yaml new file mode 100644 index 0000000000..4c1cbf43e8 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/seama.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/seama.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Seattle Image Partitions + +description: The SEAttle iMAge (SEAMA) partition is a type of partition + used for NAND flash devices. This type of flash image is found in some + D-Link routers such as DIR-645, DIR-842, DIR-859, DIR-860L, DIR-885L, + DIR890L and DCH-M225, as well as in WD and NEC routers on the ath79 + (MIPS), Broadcom BCM53xx, and RAMIPS platforms. This partition type + does not have children defined in the device tree, they need to be + detected by software. + +allOf: + - $ref: partition.yaml# + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +properties: + compatible: + const: seama + +required: + - compatible + +unevaluatedProperties: false + +examples: + - | + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + compatible = "seama"; + reg = <0x0 0x800000>; + label = "firmware"; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/partitions/tplink,safeloader-partitions.yaml b/Documentation/devicetree/bindings/mtd/partitions/tplink,safeloader-partitions.yaml new file mode 100644 index 0000000000..a24bbaac3a --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/tplink,safeloader-partitions.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/tplink,safeloader-partitions.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TP-Link SafeLoader partitions + +description: | + TP-Link home routers store various data on flash (e.g. bootloader, + flash layout, firmware, product info, configuration, calibration + data). That requires flash partitioning. + + Flash space layout of TP-Link devices is stored on flash itself using + a custom ASCII-based format. That format was first found in TP-Link + devices with a custom SafeLoader bootloader. Later it was adapted to + CFE and U-Boot bootloaders. + + Partitions specified in partitions table cover whole flash space. Some + contain static data that shouldn't get modified (device's MAC or WiFi + calibration data). Others are semi-static (like kernel). Finally some + partitions contain fully changeable content (like rootfs). + + This binding describes partitioning method and defines offset of ASCII + based partitions table. That offset is picked at manufacturing process + and doesn't change. + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +properties: + compatible: + const: tplink,safeloader-partitions + + partitions-table-offset: + description: Flash offset of partitions table + $ref: /schemas/types.yaml#/definitions/uint32 + +patternProperties: + "^partition-.*$": + $ref: partition.yaml# + +required: + - partitions-table-offset + +additionalProperties: false + +examples: + - | + partitions { + compatible = "tplink,safeloader-partitions"; + partitions-table-offset = <0x100000>; + + partition-file-system { + linux,rootfs; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/partitions/u-boot.yaml b/Documentation/devicetree/bindings/mtd/partitions/u-boot.yaml new file mode 100644 index 0000000000..3c56efe48e --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/u-boot.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/u-boot.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: U-Boot bootloader partition + +description: | + U-Boot is a bootlodaer commonly used in embedded devices. It's almost always + located on some kind of flash device. + + Device configuration is stored as a set of environment variables that are + located in a (usually standalone) block of data. + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +allOf: + - $ref: partition.yaml# + +properties: + compatible: + oneOf: + - const: brcm,u-boot + description: | + Broadcom stores environment variables inside a U-Boot partition. They + can be identified by a custom header with magic value. + +patternProperties: + "^partition-.*$": + $ref: partition.yaml# + +unevaluatedProperties: false + +examples: + - | + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + compatible = "brcm,u-boot"; + reg = <0x0 0x100000>; + label = "u-boot"; + + partition-u-boot-env { + }; + }; + + partition@100000 { + reg = <0x100000 0x1ff00000>; + label = "firmware"; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml b/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml new file mode 100644 index 0000000000..4ada60fbf8 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml @@ -0,0 +1,233 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/qcom,nandc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm NAND controller + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +properties: + compatible: + enum: + - qcom,ipq806x-nand + - qcom,ipq4019-nand + - qcom,ipq6018-nand + - qcom,ipq8074-nand + - qcom,sdx55-nand + + reg: + maxItems: 1 + + clocks: + items: + - description: Core Clock + - description: Always ON Clock + + clock-names: + items: + - const: core + - const: aon + +patternProperties: + "^nand@[a-f0-9]$": + type: object + $ref: raw-nand-chip.yaml + properties: + + nand-bus-width: + const: 8 + + nand-ecc-strength: + enum: [1, 4, 8] + + nand-ecc-step-size: + enum: + - 512 + + qcom,boot-partitions: + $ref: /schemas/types.yaml#/definitions/uint32-matrix + items: + items: + - description: offset + - description: size + description: + Boot partition use a different layout where the 4 bytes of spare + data are not protected by ECC. Use this to declare these special + partitions by defining first the offset and then the size. + + It's in the form of <offset1 size1 offset2 size2 offset3 ...> + and should be declared in ascending order. + + Refer to the ipq8064 example on how to use this special binding. + + unevaluatedProperties: false + +allOf: + - $ref: nand-controller.yaml# + + - if: + properties: + compatible: + contains: + const: qcom,ipq806x-nand + then: + properties: + dmas: + items: + - description: rxtx DMA channel + + dma-names: + items: + - const: rxtx + + qcom,cmd-crci: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Must contain the ADM command type CRCI block instance number + specified for the NAND controller on the given platform + + qcom,data-crci: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Must contain the ADM data type CRCI block instance number + specified for the NAND controller on the given platform + + - if: + properties: + compatible: + contains: + enum: + - qcom,ipq4019-nand + - qcom,ipq6018-nand + - qcom,ipq8074-nand + - qcom,sdx55-nand + + then: + properties: + dmas: + items: + - description: tx DMA channel + - description: rx DMA channel + - description: cmd DMA channel + + dma-names: + items: + - const: tx + - const: rx + - const: cmd + + - if: + properties: + compatible: + contains: + enum: + - qcom,ipq806x-nand + + then: + patternProperties: + "^nand@[a-f0-9]$": + properties: + qcom,boot-partitions: true + else: + patternProperties: + "^nand@[a-f0-9]$": + properties: + qcom,boot-partitions: false + +required: + - compatible + - reg + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-ipq806x.h> + nand-controller@1ac00000 { + compatible = "qcom,ipq806x-nand"; + reg = <0x1ac00000 0x800>; + + clocks = <&gcc EBI2_CLK>, + <&gcc EBI2_AON_CLK>; + clock-names = "core", "aon"; + + dmas = <&adm_dma 3>; + dma-names = "rxtx"; + qcom,cmd-crci = <15>; + qcom,data-crci = <3>; + + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + + qcom,boot-partitions = <0x0 0x58a0000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot-nand"; + reg = <0 0x58a0000>; + }; + + partition@58a0000 { + label = "fs-nand"; + reg = <0x58a0000 0x4000000>; + }; + }; + }; + }; + + #include <dt-bindings/clock/qcom,gcc-ipq4019.h> + nand-controller@79b0000 { + compatible = "qcom,ipq4019-nand"; + reg = <0x79b0000 0x1000>; + + clocks = <&gcc GCC_QPIC_CLK>, + <&gcc GCC_QPIC_AHB_CLK>; + clock-names = "core", "aon"; + + dmas = <&qpicbam 0>, + <&qpicbam 1>, + <&qpicbam 2>; + dma-names = "tx", "rx", "cmd"; + + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + nand-ecc-strength = <4>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot-nand"; + reg = <0 0x58a0000>; + }; + + partition@58a0000 { + label = "fs-nand"; + reg = <0x58a0000 0x4000000>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/mtd/raw-nand-chip.yaml b/Documentation/devicetree/bindings/mtd/raw-nand-chip.yaml new file mode 100644 index 0000000000..092448d7bf --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/raw-nand-chip.yaml @@ -0,0 +1,111 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/raw-nand-chip.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Raw NAND Chip Common Properties + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +allOf: + - $ref: nand-chip.yaml# + +description: | + The ECC strength and ECC step size properties define the user + desires in terms of correction capability of a controller. Together, + they request the ECC engine to correct {strength} bit errors per + {size} bytes for a particular raw NAND chip. + + The interpretation of these parameters is implementation-defined, so + not all implementations must support all possible + combinations. However, implementations are encouraged to further + specify the value(s) they support. + +properties: + $nodename: + pattern: "^nand@[a-f0-9]$" + + reg: + description: + Contains the chip-select IDs. + + nand-ecc-placement: + description: + Location of the ECC bytes. This location is unknown by default + but can be explicitly set to "oob", if all ECC bytes are + known to be stored in the OOB area, or "interleaved" if ECC + bytes will be interleaved with regular data in the main area. + $ref: /schemas/types.yaml#/definitions/string + enum: [ oob, interleaved ] + deprecated: true + + nand-ecc-mode: + description: + Legacy ECC configuration mixing the ECC engine choice and + configuration. + $ref: /schemas/types.yaml#/definitions/string + enum: [none, soft, soft_bch, hw, hw_syndrome, on-die] + deprecated: true + + nand-bus-width: + description: + Bus width to the NAND chip + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [8, 16] + default: 8 + + nand-on-flash-bbt: + description: + With this property, the OS will search the device for a Bad + Block Table (BBT). If not found, it will create one, reserve + a few blocks at the end of the device to store it and update + it as the device ages. Otherwise, the out-of-band area of a + few pages of all the blocks will be scanned at boot time to + find Bad Block Markers (BBM). These markers will help to + build a volatile BBT in RAM. + $ref: /schemas/types.yaml#/definitions/flag + + nand-ecc-maximize: + description: + Whether or not the ECC strength should be maximized. The + maximum ECC strength is both controller and chip + dependent. The ECC engine has to select the ECC config + providing the best strength and taking the OOB area size + constraint into account. This is particularly useful when + only the in-band area is used by the upper layers, and you + want to make your NAND as reliable as possible. + $ref: /schemas/types.yaml#/definitions/flag + + nand-is-boot-medium: + description: + Whether or not the NAND chip is a boot medium. Drivers might + use this information to select ECC algorithms supported by + the boot ROM or similar restrictions. + $ref: /schemas/types.yaml#/definitions/flag + + nand-rb: + description: + Contains the native Ready/Busy IDs. + $ref: /schemas/types.yaml#/definitions/uint32-array + + rb-gpios: + description: + Contains one or more GPIO descriptor (the numper of descriptor + depends on the number of R/B pins exposed by the flash) for the + Ready/Busy pins. Active state refers to the NAND ready state and + should be set to GPIOD_ACTIVE_HIGH unless the signal is inverted. + + wp-gpios: + description: + Contains one GPIO descriptor for the Write Protect pin. + Active state refers to the NAND Write Protect state and should be + set to GPIOD_ACTIVE_LOW unless the signal is inverted. + maxItems: 1 + +required: + - reg + +# This is a generic file other binding inherit from and extend +additionalProperties: true diff --git a/Documentation/devicetree/bindings/mtd/renesas-nandc.yaml b/Documentation/devicetree/bindings/mtd/renesas-nandc.yaml new file mode 100644 index 0000000000..cc6b8274e6 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/renesas-nandc.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/renesas-nandc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car Gen3 & RZ/N1x NAND flash controller + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +allOf: + - $ref: nand-controller.yaml + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,r9a06g032-nandc + - const: renesas,rzn1-nandc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: APB host controller clock + - description: External NAND bus clock + + clock-names: + items: + - const: hclk + - const: eclk + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - clock-names + - power-domains + - interrupts + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/r9a06g032-sysctrl.h> + + nand-controller@40102000 { + compatible = "renesas,r9a06g032-nandc", "renesas,rzn1-nandc"; + reg = <0x40102000 0x2000>; + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sysctrl R9A06G032_HCLK_NAND>, <&sysctrl R9A06G032_CLK_NAND>; + clock-names = "hclk", "eclk"; + power-domains = <&sysctrl>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/mtd/rockchip,nand-controller.yaml b/Documentation/devicetree/bindings/mtd/rockchip,nand-controller.yaml new file mode 100644 index 0000000000..ee53715ffd --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/rockchip,nand-controller.yaml @@ -0,0 +1,165 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/rockchip,nand-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip SoCs NAND FLASH Controller (NFC) + +allOf: + - $ref: nand-controller.yaml# + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +properties: + compatible: + oneOf: + - const: rockchip,px30-nfc + - const: rockchip,rk2928-nfc + - const: rockchip,rv1108-nfc + - items: + - enum: + - rockchip,rk3036-nfc + - rockchip,rk3128-nfc + - const: rockchip,rk2928-nfc + - items: + - const: rockchip,rk3308-nfc + - const: rockchip,rv1108-nfc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + minItems: 1 + items: + - const: ahb + - const: nfc + + assigned-clocks: + maxItems: 1 + + assigned-clock-rates: + maxItems: 1 + + power-domains: + maxItems: 1 + +patternProperties: + "^nand@[0-7]$": + type: object + $ref: raw-nand-chip.yaml + properties: + reg: + minimum: 0 + maximum: 7 + + nand-ecc-mode: + const: hw + + nand-ecc-step-size: + const: 1024 + + nand-ecc-strength: + enum: [16, 24, 40, 60, 70] + description: | + The ECC configurations that can be supported are as follows. + NFC v600 ECC 16, 24, 40, 60 + RK2928, RK3066, RK3188 + + NFC v622 ECC 16, 24, 40, 60 + RK3036, RK3128 + + NFC v800 ECC 16 + RK3308, RV1108 + + NFC v900 ECC 16, 40, 60, 70 + RK3326, PX30 + + nand-bus-width: + const: 8 + + rockchip,boot-blks: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 2 + default: 16 + description: + The NFC driver need this information to select ECC + algorithms supported by the boot ROM. + Only used in combination with 'nand-is-boot-medium'. + + rockchip,boot-ecc-strength: + enum: [16, 24, 40, 60, 70] + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + If specified it indicates that a different BCH/ECC setting is + supported by the boot ROM. + NFC v600 ECC 16, 24 + RK2928, RK3066, RK3188 + + NFC v622 ECC 16, 24, 40, 60 + RK3036, RK3128 + + NFC v800 ECC 16 + RK3308, RV1108 + + NFC v900 ECC 16, 70 + RK3326, PX30 + + Only used in combination with 'nand-is-boot-medium'. + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3308-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + nfc: nand-controller@ff4b0000 { + compatible = "rockchip,rk3308-nfc", + "rockchip,rv1108-nfc"; + reg = <0xff4b0000 0x4000>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru HCLK_NANDC>, <&cru SCLK_NANDC>; + clock-names = "ahb", "nfc"; + assigned-clocks = <&clks SCLK_NANDC>; + assigned-clock-rates = <150000000>; + + pinctrl-0 = <&flash_ale &flash_bus8 &flash_cle &flash_csn0 + &flash_rdn &flash_rdy &flash_wrn>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + label = "rk-nand"; + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-ecc-step-size = <1024>; + nand-ecc-strength = <16>; + nand-is-boot-medium; + rockchip,boot-blks = <8>; + rockchip,boot-ecc-strength = <16>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/mtd/samsung-s3c2410.txt b/Documentation/devicetree/bindings/mtd/samsung-s3c2410.txt new file mode 100644 index 0000000000..09815c40fc --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/samsung-s3c2410.txt @@ -0,0 +1,56 @@ +* Samsung S3C2410 and compatible NAND flash controller + +Required properties: +- compatible : The possible values are: + "samsung,s3c2410-nand" + "samsung,s3c2412-nand" + "samsung,s3c2440-nand" +- reg : register's location and length. +- #address-cells, #size-cells : see nand-controller.yaml +- clocks : phandle to the nand controller clock +- clock-names : must contain "nand" + +Optional child nodes: +Child nodes representing the available nand chips. + +Optional child properties: +- nand-ecc-mode : see nand-controller.yaml +- nand-on-flash-bbt : see nand-controller.yaml + +Each child device node may optionally contain a 'partitions' sub-node, +which further contains sub-nodes describing the flash partition mapping. +See partition.txt for more detail. + +Example: + +nand-controller@4e000000 { + compatible = "samsung,s3c2440-nand"; + reg = <0x4e000000 0x40>; + + #address-cells = <1>; + #size-cells = <0>; + + clocks = <&clocks HCLK_NAND>; + clock-names = "nand"; + + nand { + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0 0x040000>; + }; + + partition@40000 { + label = "kernel"; + reg = <0x040000 0x500000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/spear_smi.txt b/Documentation/devicetree/bindings/mtd/spear_smi.txt new file mode 100644 index 0000000000..c41873e92d --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/spear_smi.txt @@ -0,0 +1,29 @@ +* SPEAr SMI + +Required properties: +- compatible : "st,spear600-smi" +- reg : Address range of the mtd chip +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. +- interrupts: Should contain the STMMAC interrupts +- clock-rate : Functional clock rate of SMI in Hz + +Optional properties: +- st,smi-fast-mode : Flash supports read in fast mode + +Example: + + smi: flash@fc000000 { + compatible = "st,spear600-smi"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xfc000000 0x1000>; + interrupt-parent = <&vic1>; + interrupts = <12>; + clock-rate = <50000000>; /* 50MHz */ + + flash@f8000000 { + st,smi-fast-mode; + ... + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/spi-nand.yaml b/Documentation/devicetree/bindings/mtd/spi-nand.yaml new file mode 100644 index 0000000000..77a8727c79 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/spi-nand.yaml @@ -0,0 +1,28 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/spi-nand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SPI-NAND flash + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +allOf: + - $ref: nand-chip.yaml# + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +properties: + compatible: + const: spi-nand + + reg: + description: Encode the chip-select line on the SPI bus + maxItems: 1 + +required: + - compatible + - reg + +unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/mtd/st,stm32-fmc2-nand.yaml b/Documentation/devicetree/bindings/mtd/st,stm32-fmc2-nand.yaml new file mode 100644 index 0000000000..e72cb5baca --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/st,stm32-fmc2-nand.yaml @@ -0,0 +1,135 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/st,stm32-fmc2-nand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics Flexible Memory Controller 2 (FMC2) + +maintainers: + - Christophe Kerello <christophe.kerello@foss.st.com> + +properties: + compatible: + enum: + - st,stm32mp15-fmc2 + - st,stm32mp1-fmc2-nfc + + reg: + minItems: 6 + maxItems: 7 + + interrupts: + maxItems: 1 + + dmas: + items: + - description: tx DMA channel + - description: rx DMA channel + - description: ecc DMA channel + + dma-names: + items: + - const: tx + - const: rx + - const: ecc + +patternProperties: + "^nand@[a-f0-9]$": + type: object + $ref: raw-nand-chip.yaml + properties: + nand-ecc-step-size: + const: 512 + + nand-ecc-strength: + enum: [1, 4, 8] + + unevaluatedProperties: false + +allOf: + - $ref: nand-controller.yaml# + + - if: + properties: + compatible: + contains: + const: st,stm32mp15-fmc2 + then: + properties: + reg: + items: + - description: Registers + - description: Chip select 0 data + - description: Chip select 0 command + - description: Chip select 0 address space + - description: Chip select 1 data + - description: Chip select 1 command + - description: Chip select 1 address space + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + required: + - clocks + + - if: + properties: + compatible: + contains: + const: st,stm32mp1-fmc2-nfc + then: + properties: + reg: + items: + - description: Chip select 0 data + - description: Chip select 0 command + - description: Chip select 0 address space + - description: Chip select 1 data + - description: Chip select 1 command + - description: Chip select 1 address space + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/stm32mp1-clks.h> + #include <dt-bindings/reset/stm32mp1-resets.h> + + nand-controller@58002000 { + compatible = "st,stm32mp15-fmc2"; + reg = <0x58002000 0x1000>, + <0x80000000 0x1000>, + <0x88010000 0x1000>, + <0x88020000 0x1000>, + <0x81000000 0x1000>, + <0x89010000 0x1000>, + <0x89020000 0x1000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>, + <&mdma1 20 0x2 0x12000a08 0x0 0x0>, + <&mdma1 21 0x2 0x12000a0a 0x0 0x0>; + dma-names = "tx", "rx", "ecc"; + clocks = <&rcc FMC_K>; + resets = <&rcc FMC_R>; + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + nand-on-flash-bbt; + #address-cells = <1>; + #size-cells = <1>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/mtd/st-fsm.txt b/Documentation/devicetree/bindings/mtd/st-fsm.txt new file mode 100644 index 0000000000..54cef9ef30 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/st-fsm.txt @@ -0,0 +1,25 @@ +* ST-Microelectronics SPI FSM Serial (NOR) Flash Controller + +Required properties: + - compatible : Should be "st,spi-fsm" + - reg : Contains register's location and length. + - reg-names : Should contain the reg names "spi-fsm" + - interrupts : The interrupt number + - pinctrl-0 : Standard Pinctrl phandle (see: pinctrl/pinctrl-bindings.txt) + +Optional properties: + - st,syscfg : Phandle to boot-device system configuration registers + - st,boot-device-reg : Address of the aforementioned boot-device register(s) + - st,boot-device-spi : Expected boot-device value if booted via this device + +Example: + spifsm: spifsm@fe902000{ + compatible = "st,spi-fsm"; + reg = <0xfe902000 0x1000>; + reg-names = "spi-fsm"; + pinctrl-0 = <&pinctrl_fsm>; + st,syscfg = <&syscfg_rear>; + st,boot-device-reg = <0x958>; + st,boot-device-spi = <0x1a>; + }; + diff --git a/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.yaml b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.yaml new file mode 100644 index 0000000000..df4fdc0245 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.yaml @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/ti,am654-hbmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: HyperBus Memory Controller (HBMC) on TI's K3 family of SoCs + +maintainers: + - Vignesh Raghavendra <vigneshr@ti.com> + +properties: + compatible: + const: ti,am654-hbmc + + reg: + maxItems: 2 + + power-domains: true + '#address-cells': true + '#size-cells': true + ranges: true + + mux-controls: + description: MMIO mux controller node to select b/w OSPI and HBMC. + + clocks: + maxItems: 1 + +patternProperties: + "^flash@[0-1],[0-9a-f]+$": + type: object + $ref: mtd-physmap.yaml + unevaluatedProperties: false + +required: + - compatible + - reg + - ranges + - clocks + - '#address-cells' + - '#size-cells' + +additionalProperties: false + +examples: + - | + bus { + #address-cells = <2>; + #size-cells = <2>; + + hbmc: memory-controller@47034000 { + compatible = "ti,am654-hbmc"; + reg = <0x0 0x47034000 0x0 0x100>, + <0x5 0x00000000 0x1 0x0000000>; + ranges = <0x0 0x0 0x5 0x00000000 0x4000000>, /* CS0 - 64MB */ + <0x1 0x0 0x5 0x04000000 0x4000000>; /* CS1 - 64MB */ + clocks = <&k3_clks 102 0>; + #address-cells = <2>; + #size-cells = <1>; + power-domains = <&k3_pds 55>; + mux-controls = <&hbmc_mux 0>; + + flash@0,0 { + compatible = "cypress,hyperflash", "cfi-flash"; + reg = <0x0 0x0 0x4000000>; + #address-cells = <1>; + #size-cells = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/ti,elm.yaml b/Documentation/devicetree/bindings/mtd/ti,elm.yaml new file mode 100644 index 0000000000..87128c0045 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/ti,elm.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/ti,elm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments Error Location Module (ELM). + +maintainers: + - Roger Quadros <rogerq@kernel.org> + +description: + ELM module is used together with GPMC and NAND Flash to detect + errors and the location of the error based on BCH algorithms + so they can be corrected if possible. + +properties: + compatible: + enum: + - ti,am3352-elm + - ti,am64-elm + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + description: Functional clock. + + clock-names: + items: + - const: fck + + power-domains: + maxItems: 1 + + ti,hwmods: + description: + Name of the HWMOD associated with ELM. This is for legacy + platforms only. + $ref: /schemas/types.yaml#/definitions/string + deprecated: true + +required: + - compatible + - reg + - interrupts + +allOf: + - if: + properties: + compatible: + contains: + const: ti,am64-elm + then: + required: + - clocks + - clock-names + - power-domains + +additionalProperties: false + +examples: + - | + elm: ecc@0 { + compatible = "ti,am3352-elm"; + reg = <0x0 0x2000>; + interrupts = <4>; + }; diff --git a/Documentation/devicetree/bindings/mtd/ti,gpmc-nand.yaml b/Documentation/devicetree/bindings/mtd/ti,gpmc-nand.yaml new file mode 100644 index 0000000000..115682fa81 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/ti,gpmc-nand.yaml @@ -0,0 +1,129 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/ti,gpmc-nand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments GPMC NAND Flash controller. + +maintainers: + - Tony Lindgren <tony@atomide.com> + - Roger Quadros <rogerq@kernel.org> + +description: + GPMC NAND controller/Flash is represented as a child of the + GPMC controller node. + +properties: + compatible: + items: + - enum: + - ti,am64-nand + - ti,omap2-nand + + reg: + maxItems: 1 + + interrupts: + items: + - description: Interrupt for fifoevent + - description: Interrupt for termcount + + "#address-cells": true + + "#size-cells": true + + ti,nand-ecc-opt: + description: Desired ECC algorithm + $ref: /schemas/types.yaml#/definitions/string + enum: [sw, ham1, bch4, bch8, bch16] + + ti,nand-xfer-type: + description: Data transfer method between controller and chip. + $ref: /schemas/types.yaml#/definitions/string + enum: [prefetch-polled, polled, prefetch-dma, prefetch-irq] + default: prefetch-polled + + ti,elm-id: + description: + phandle to the ELM (Error Location Module). + $ref: /schemas/types.yaml#/definitions/phandle + + nand-bus-width: + description: + Bus width to the NAND chip + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [8, 16] + default: 8 + + rb-gpios: + description: + GPIO connection to R/B signal from NAND chip + maxItems: 1 + +patternProperties: + "@[0-9a-f]+$": + $ref: /schemas/mtd/partitions/partition.yaml + +allOf: + - $ref: /schemas/memory-controllers/ti,gpmc-child.yaml + +required: + - compatible + - reg + - ti,nand-ecc-opt + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/gpio/gpio.h> + + gpmc: memory-controller@50000000 { + compatible = "ti,am3352-gpmc"; + dmas = <&edma 52 0>; + dma-names = "rxtx"; + clocks = <&l3s_gclk>; + clock-names = "fck"; + reg = <0x50000000 0x2000>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + gpmc,num-cs = <7>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + + ranges = <0 0 0x08000000 0x01000000>; /* CS0 space. Min partition = 16MB */ + nand@0,0 { + compatible = "ti,omap2-nand"; + reg = <0 0 4>; /* device IO registers */ + interrupt-parent = <&gpmc>; + interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ + <1 IRQ_TYPE_NONE>; /* termcount */ + ti,nand-xfer-type = "prefetch-dma"; + ti,nand-ecc-opt = "bch16"; + ti,elm-id = <&elm>; + #address-cells = <1>; + #size-cells = <1>; + + /* NAND generic properties */ + nand-bus-width = <8>; + rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */ + + /* GPMC properties*/ + gpmc,device-width = <1>; + + partition@0 { + label = "NAND.SPL"; + reg = <0x00000000 0x00040000>; + }; + partition@1 { + label = "NAND.SPL.backup1"; + reg = <0x00040000 0x00040000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/ti,gpmc-onenand.yaml b/Documentation/devicetree/bindings/mtd/ti,gpmc-onenand.yaml new file mode 100644 index 0000000000..7d3ace4f55 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/ti,gpmc-onenand.yaml @@ -0,0 +1,84 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/ti,gpmc-onenand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OneNAND over Texas Instruments GPMC bus. + +maintainers: + - Tony Lindgren <tony@atomide.com> + - Roger Quadros <rogerq@kernel.org> + +description: + GPMC connected OneNAND (found on OMAP boards) are represented + as child nodes of the GPMC controller. + +properties: + $nodename: + pattern: "^onenand@[0-9],[0,9]$" + + compatible: + const: ti,omap2-onenand + + reg: + items: + - description: | + Chip Select number, register offset and size of + OneNAND register window. + + "#address-cells": true + + "#size-cells": true + + int-gpios: + description: GPIO specifier for the INT pin. + +patternProperties: + "@[0-9a-f]+$": + $ref: /schemas/mtd/partitions/partition.yaml + +allOf: + - $ref: /schemas/memory-controllers/ti,gpmc-child.yaml + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + +unevaluatedProperties: false + +examples: + - | + gpmc: memory-controller@6e000000 { + compatible = "ti,omap3430-gpmc"; + reg = <0x6e000000 0x02d0>; + interrupts = <20>; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <4>; + clocks = <&l3s_clkctrl>; + clock-names = "fck"; + #address-cells = <2>; + #size-cells = <1>; + + ranges = <0 0 0x01000000 0x01000000>, /* 16 MB for OneNAND */ + <1 0 0x02000000 0x01000000>; /* 16 MB for smc91c96 */ + + onenand@0,0 { + compatible = "ti,omap2-onenand"; + reg = <0 0 0x20000>; /* CS0, offset 0, IO size 128K */ + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bootloader"; + reg = <0x00000000 0x00100000>; + }; + + partition@100000 { + label = "config"; + reg = <0x00100000 0x002c0000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/vf610-nfc.txt b/Documentation/devicetree/bindings/mtd/vf610-nfc.txt new file mode 100644 index 0000000000..7db5e6e609 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/vf610-nfc.txt @@ -0,0 +1,59 @@ +Freescale's NAND flash controller (NFC) + +This variant of the Freescale NAND flash controller (NFC) can be found on +Vybrid (vf610), MPC5125, MCF54418 and Kinetis K70. + +Required properties: +- compatible: Should be set to "fsl,vf610-nfc". +- reg: address range of the NFC. +- interrupts: interrupt of the NFC. +- #address-cells: shall be set to 1. Encode the nand CS. +- #size-cells : shall be set to 0. +- assigned-clocks: main clock from the SoC, for Vybrid <&clks VF610_CLK_NFC>; +- assigned-clock-rates: The NAND bus timing is derived from this clock + rate and should not exceed maximum timing for any NAND memory chip + in a board stuffing. Typical NAND memory timings derived from this + clock are found in the SoC hardware reference manual. Furthermore, + there might be restrictions on maximum rates when using hardware ECC. + +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. + +Required children nodes: +Children nodes represent the available nand chips. Currently the driver can +only handle one NAND chip. + +Required properties: +- compatible: Should be set to "fsl,vf610-nfc-cs". +- nand-bus-width: see nand-controller.yaml +- nand-ecc-mode: see nand-controller.yaml + +Required properties for hardware ECC: +- nand-ecc-strength: supported strengths are 24 and 32 bit (see nand-controller.yaml) +- nand-ecc-step-size: step size equals page size, currently only 2k pages are + supported +- nand-on-flash-bbt: see nand-controller.yaml + +Example: + + nfc: nand@400e0000 { + compatible = "fsl,vf610-nfc"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x400e0000 0x4000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks VF610_CLK_NFC>; + clock-names = "nfc"; + assigned-clocks = <&clks VF610_CLK_NFC>; + assigned-clock-rates = <33000000>; + + nand@0 { + compatible = "fsl,vf610-nfc-nandcs"; + reg = <0>; + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <32>; + nand-ecc-step-size = <2048>; + nand-on-flash-bbt; + }; + }; |