diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml | 198 |
1 files changed, 198 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml b/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml new file mode 100644 index 0000000000..4d5f5cc6d0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml @@ -0,0 +1,198 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/nxp,sja1105.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP SJA1105 Automotive Ethernet Switch Family + +description: + The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944.pdf) of at + least one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum + cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed + depends on the SPI bus master driver. + +maintainers: + - Vladimir Oltean <vladimir.oltean@nxp.com> + +properties: + compatible: + enum: + - nxp,sja1105e + - nxp,sja1105t + - nxp,sja1105p + - nxp,sja1105q + - nxp,sja1105r + - nxp,sja1105s + - nxp,sja1110a + - nxp,sja1110b + - nxp,sja1110c + - nxp,sja1110d + + reg: + maxItems: 1 + + spi-cpha: true + spi-cpol: true + + # Optional container node for the 2 internal MDIO buses of the SJA1110 + # (one for the internal 100base-T1 PHYs and the other for the single + # 100base-TX PHY). The "reg" property does not have physical significance. + # The PHY addresses to port correspondence is as follows: for 100base-T1, + # port 5 has PHY 1, port 6 has PHY 2 etc, while for 100base-TX, port 1 has + # PHY 1. + mdios: + type: object + + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + patternProperties: + "^mdio@[0-1]$": + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + + properties: + compatible: + oneOf: + - enum: + - nxp,sja1110-base-t1-mdio + - nxp,sja1110-base-tx-mdio + + reg: + oneOf: + - enum: + - 0 + - 1 + + required: + - compatible + - reg + +patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-9]+$": + allOf: + - if: + properties: + phy-mode: + contains: + enum: + - rgmii + - rgmii-rxid + - rgmii-txid + - rgmii-id + then: + properties: + rx-internal-delay-ps: + $ref: "#/$defs/internal-delay-ps" + tx-internal-delay-ps: + $ref: "#/$defs/internal-delay-ps" + +required: + - compatible + - reg + +$defs: + internal-delay-ps: + description: + Disable tunable delay lines using 0 ps, or enable them and select + the phase between 1640 ps (73.8 degree shift at 1Gbps) and 2260 ps + (101.7 degree shift) in increments of 0.9 degrees (20 ps). + enum: + [0, 1640, 1660, 1680, 1700, 1720, 1740, 1760, 1780, 1800, 1820, 1840, + 1860, 1880, 1900, 1920, 1940, 1960, 1980, 2000, 2020, 2040, 2060, 2080, + 2100, 2120, 2140, 2160, 2180, 2200, 2220, 2240, 2260] + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + - $ref: /schemas/spi/spi-peripheral-props.yaml# + - if: + properties: + compatible: + enum: + - nxp,sja1105e + - nxp,sja1105p + - nxp,sja1105q + - nxp,sja1105r + - nxp,sja1105s + - nxp,sja1105t + then: + properties: + spi-cpol: false + required: + - spi-cpha + else: + properties: + spi-cpha: false + required: + - spi-cpol + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@1 { + reg = <0x1>; + compatible = "nxp,sja1105t"; + spi-cpha; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + phy-handle = <&rgmii_phy6>; + phy-mode = "rgmii-id"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + reg = <0>; + }; + + port@1 { + phy-handle = <&rgmii_phy3>; + phy-mode = "rgmii-id"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + reg = <1>; + }; + + port@2 { + phy-handle = <&rgmii_phy4>; + phy-mode = "rgmii-id"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + reg = <2>; + }; + + port@3 { + phy-handle = <&rgmii_phy4>; + phy-mode = "rgmii-id"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + reg = <3>; + }; + + port@4 { + ethernet = <&enet2>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + reg = <4>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; |