diff options
Diffstat (limited to 'Documentation/devicetree/bindings/phy/mediatek,tphy.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/phy/mediatek,tphy.yaml | 313 |
1 files changed, 313 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml new file mode 100644 index 0000000000..2bb91542e9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml @@ -0,0 +1,313 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/mediatek,tphy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek T-PHY Controller + +maintainers: + - Chunfeng Yun <chunfeng.yun@mediatek.com> + +description: | + The T-PHY controller supports physical layer functionality for a number of + controllers on MediaTek SoCs, includes USB2.0, USB3.0, PCIe and SATA. + + Layout differences of banks between T-PHY V1 (mt8173/mt2701) and + T-PHY V2 (mt2712) / V3 (mt8195) when works on USB mode: + ----------------------------------- + Version 1: + port offset bank + shared 0x0000 SPLLC + 0x0100 FMREG + u2 port0 0x0800 U2PHY_COM + u3 port0 0x0900 U3PHYD + 0x0a00 U3PHYD_BANK2 + 0x0b00 U3PHYA + 0x0c00 U3PHYA_DA + u2 port1 0x1000 U2PHY_COM + u3 port1 0x1100 U3PHYD + 0x1200 U3PHYD_BANK2 + 0x1300 U3PHYA + 0x1400 U3PHYA_DA + u2 port2 0x1800 U2PHY_COM + ... + + Version 2/3: + port offset bank + u2 port0 0x0000 MISC + 0x0100 FMREG + 0x0300 U2PHY_COM + u3 port0 0x0700 SPLLC + 0x0800 CHIP + 0x0900 U3PHYD + 0x0a00 U3PHYD_BANK2 + 0x0b00 U3PHYA + 0x0c00 U3PHYA_DA + u2 port1 0x1000 MISC + 0x1100 FMREG + 0x1300 U2PHY_COM + u3 port1 0x1700 SPLLC + 0x1800 CHIP + 0x1900 U3PHYD + 0x1a00 U3PHYD_BANK2 + 0x1b00 U3PHYA + 0x1c00 U3PHYA_DA + u2 port2 0x2000 MISC + ... + + SPLLC shared by u3 ports and FMREG shared by u2 ports on V1 are put back + into each port; a new bank MISC for u2 ports and CHIP for u3 ports are + added on V2; the FMREG bank for slew rate calibration is not used anymore + and reserved on V3; + +properties: + $nodename: + pattern: "^t-phy(@[0-9a-f]+)?$" + + compatible: + oneOf: + - items: + - enum: + - mediatek,mt2701-tphy + - mediatek,mt7623-tphy + - mediatek,mt7622-tphy + - mediatek,mt8516-tphy + - const: mediatek,generic-tphy-v1 + - items: + - enum: + - mediatek,mt2712-tphy + - mediatek,mt7629-tphy + - mediatek,mt7986-tphy + - mediatek,mt8183-tphy + - mediatek,mt8186-tphy + - mediatek,mt8192-tphy + - mediatek,mt8365-tphy + - const: mediatek,generic-tphy-v2 + - items: + - enum: + - mediatek,mt8188-tphy + - mediatek,mt8195-tphy + - const: mediatek,generic-tphy-v3 + - const: mediatek,mt2701-u3phy + deprecated: true + - const: mediatek,mt2712-u3phy + deprecated: true + - const: mediatek,mt8173-u3phy + + reg: + description: + Register shared by multiple ports, exclude port's private register. + It is needed for T-PHY V1, such as mt2701 and mt8173, but not for + T-PHY V2/V3, such as mt2712. + maxItems: 1 + + "#address-cells": + enum: [1, 2] + + "#size-cells": + enum: [1, 2] + + # Used with non-empty value if optional 'reg' is not provided. + # The format of the value is an arbitrary number of triplets of + # (child-bus-address, parent-bus-address, length). + ranges: true + + mediatek,src-ref-clk-mhz: + description: + Frequency of reference clock for slew rate calibrate + default: 26 + + mediatek,src-coef: + description: + Coefficient for slew rate calibrate, depends on SoC process + $ref: /schemas/types.yaml#/definitions/uint32 + default: 28 + +# Required child node: +patternProperties: + "^(usb|pcie|sata)-phy@[0-9a-f]+$": + type: object + description: + A sub-node is required for each port the controller provides. + Address range information including the usual 'reg' property + is used inside these nodes to describe the controller's topology. + + properties: + reg: + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: Reference clock, (HS is 48Mhz, SS/P is 24~27Mhz) + - description: Reference clock of analog phy + description: + Uses both clocks if the clock of analog and digital phys are + separated, otherwise uses "ref" clock only if needed. + + clock-names: + minItems: 1 + items: + - const: ref + - const: da_ref + + "#phy-cells": + const: 1 + description: | + The cells contain the following arguments. + + - description: The PHY type + enum: + - PHY_TYPE_USB2 + - PHY_TYPE_USB3 + - PHY_TYPE_PCIE + - PHY_TYPE_SATA + - PHY_TYPE_SGMII + + nvmem-cells: + items: + - description: internal R efuse for U2 PHY or U3/PCIe PHY + - description: rx_imp_sel efuse for U3/PCIe PHY + - description: tx_imp_sel efuse for U3/PCIe PHY + description: | + Phandles to nvmem cell that contains the efuse data; + Available only for U2 PHY or U3/PCIe PHY of version 2/3, these + three items should be provided at the same time for U3/PCIe PHY, + when use software to load efuse; + If unspecified, will use hardware auto-load efuse. + + nvmem-cell-names: + items: + - const: intr + - const: rx_imp + - const: tx_imp + + # The following optional vendor properties are only for debug or HQA test + mediatek,eye-src: + description: + The value of slew rate calibrate (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 7 + + mediatek,eye-vrt: + description: + The selection of VRT reference voltage (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 7 + + mediatek,eye-term: + description: + The selection of HS_TX TERM reference voltage (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 7 + + mediatek,intr: + description: + The selection of internal resistor (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 31 + + mediatek,discth: + description: + The selection of disconnect threshold (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 15 + + mediatek,pre-emphasis: + description: + The level of pre-emphasis which used to widen the eye opening and + boost eye swing, the unit step is about 4.16% increment; e.g. the + level 1 means amplitude increases about 4.16%, the level 2 is about + 8.3% etc. (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 3 + + mediatek,bc12: + description: + Specify the flag to enable BC1.2 if support it + type: boolean + + mediatek,syscon-type: + $ref: /schemas/types.yaml#/definitions/phandle-array + maxItems: 1 + description: + A phandle to syscon used to access the register of type switch, + the field should always be 3 cells long. + items: + items: + - description: + The first cell represents a phandle to syscon + - description: + The second cell represents the register offset + - description: + The third cell represents the index of config segment + enum: [0, 1, 2, 3] + + required: + - reg + - "#phy-cells" + + additionalProperties: false + +required: + - compatible + - "#address-cells" + - "#size-cells" + - ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8173-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/phy/phy.h> + usb@11271000 { + compatible = "mediatek,mt8173-mtu3", "mediatek,mtu3"; + reg = <0x11271000 0x3000>, <0x11280700 0x0100>; + reg-names = "mac", "ippc"; + phys = <&u2port0 PHY_TYPE_USB2>, + <&u3port0 PHY_TYPE_USB3>, + <&u2port1 PHY_TYPE_USB2>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_USB30_SEL>; + clock-names = "sys_ck"; + }; + + t-phy@11290000 { + compatible = "mediatek,mt8173-u3phy"; + reg = <0x11290000 0x800>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + u2port0: usb-phy@11290800 { + reg = <0x11290800 0x100>; + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>, <&clk48m>; + clock-names = "ref", "da_ref"; + #phy-cells = <1>; + }; + + u3port0: usb-phy@11290900 { + reg = <0x11290900 0x700>; + clocks = <&clk26m>; + clock-names = "ref"; + #phy-cells = <1>; + }; + + u2port1: usb-phy@11291000 { + reg = <0x11291000 0x100>; + #phy-cells = <1>; + }; + }; + +... |