diff options
Diffstat (limited to 'Documentation/devicetree/bindings/power/supply/bq24257.yaml')
-rw-r--r-- | Documentation/devicetree/bindings/power/supply/bq24257.yaml | 124 |
1 files changed, 124 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/power/supply/bq24257.yaml b/Documentation/devicetree/bindings/power/supply/bq24257.yaml new file mode 100644 index 0000000000..eb064bbf87 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq24257.yaml @@ -0,0 +1,124 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2021 Sebastian Reichel +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/supply/bq24257.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bq24250, bq24251 and bq24257 Li-Ion Charger + +maintainers: + - Sebastian Reichel <sre@kernel.org> + +allOf: + - $ref: power-supply.yaml# + +properties: + compatible: + enum: + - ti,bq24250 + - ti,bq24251 + - ti,bq24257 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + ti,battery-regulation-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: maximum charging voltage in uV + + ti,charge-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: maximum charging current in uA + + ti,termination-current: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + charge will be terminated when current in constant-voltage phase + drops below this value (in uA) + + pg-gpios: + description: | + GPIO used for connecting the bq2425x device PG (Power Good) pin. + This pin is not available on all devices however it should be used if + possible as this is the recommended way to obtain the charger's input PG + state. If this pin is not specified a software-based approach for PG + detection is used. + maxItems: 1 + + ti,current-limit: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + The maximum current to be drawn from the charger's input (in uA). + If this property is not specified, the input limit current is set + automatically using USB D+/D- signal based charger type detection. + If the hardware does not support the D+/D- based detection, a default + of 500,000 is used (=500mA) instead. + + ti,ovp-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Configures the over voltage protection voltage (in uV). + If not specified a default of 6,5000,000 (=6.5V) is used. + + ti,in-dpm-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Configures the threshold input voltage for the dynamic power path management (in uV). + If not specified a default of 4,360,000 (=4.36V) is used. + +required: + - compatible + - reg + - interrupts + - ti,battery-regulation-voltage + - ti,charge-current + - ti,termination-current + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + charger@6a { + compatible = "ti,bq24257"; + reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <1000000>; + ti,termination-current = <50000>; + }; + }; + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + charger@6a { + compatible = "ti,bq24250"; + reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <500000>; + ti,termination-current = <50000>; + ti,current-limit = <900000>; + ti,ovp-voltage = <9500000>; + ti,in-dpm-voltage = <4440000>; + }; + }; |