diff options
Diffstat (limited to 'Documentation/devicetree/bindings/regulator/maxim,max8973.yaml')
-rw-r--r-- | Documentation/devicetree/bindings/regulator/maxim,max8973.yaml | 141 |
1 files changed, 141 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/regulator/maxim,max8973.yaml b/Documentation/devicetree/bindings/regulator/maxim,max8973.yaml new file mode 100644 index 0000000000..b92eef68c1 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/maxim,max8973.yaml @@ -0,0 +1,141 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/maxim,max8973.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim MAX8973/MAX77621 voltage regulator + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +allOf: + - $ref: regulator.yaml# + +properties: + compatible: + enum: + - maxim,max8973 + - maxim,max77621 + + junction-warn-millicelsius: + description: | + Junction warning temperature threshold in millicelsius. If die + temperature crosses this level then device generates the warning + interrupts. + Please note that thermal functionality is only supported on MAX77621. The + supported threshold warning temperature for MAX77621 are 120 degC and 140 + degC. + + maxim,dvs-gpio: + maxItems: 1 + description: | + GPIO which is connected to DVS pin of device. + + maxim,dvs-default-state: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + Default state of GPIO during initialisation. + 1 for HIGH and 0 for LOW. + + maxim,externally-enable: + type: boolean + description: | + Externally control the regulator output enable/disable. + + maxim,enable-gpio: + maxItems: 1 + description: | + GPIO for enable control. If the valid GPIO is provided then externally + enable control will be considered. + + maxim,enable-remote-sense: + type: boolean + description: Enable remote sense. + + maxim,enable-falling-slew-rate: + type: boolean + description: Enable falling slew rate. + + maxim,enable-active-discharge: + type: boolean + description: Eable active discharge. + + maxim,enable-frequency-shift: + type: boolean + description: Enable 9% frequency shift. + + maxim,enable-bias-control: + type: boolean + description: | + Enable bias control which can reduce the startup delay to 20us from 220us. + + maxim,enable-etr: + type: boolean + description: Enable Enhanced Transient Response. + + maxim,enable-high-etr-sensitivity: + type: boolean + description: | + Enhanced transient response circuit is enabled and set for high + sensitivity. If this property is available then etr will be enable + default. + Enhanced transient response (ETR) will affect the configuration of CKADV. + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + regulator@1b { + compatible = "maxim,max8973"; + reg = <0x1b>; + + regulator-min-microvolt = <935000>; + regulator-max-microvolt = <1200000>; + regulator-boot-on; + regulator-always-on; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + regulator@1b { + compatible = "maxim,max77621"; + reg = <0x1b>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1231250>; + regulator-name = "PPVAR_CPU"; + regulator-ramp-delay = <12500>; + maxim,dvs-default-state = <1>; + maxim,enable-active-discharge; + maxim,enable-bias-control; + maxim,enable-etr; + maxim,enable-gpio = <&pmic 5 GPIO_ACTIVE_HIGH>; + maxim,externally-enable; + }; + }; |