summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/sound/cs35l33.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/sound/cs35l33.txt')
-rw-r--r--Documentation/devicetree/bindings/sound/cs35l33.txt124
1 files changed, 124 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/sound/cs35l33.txt b/Documentation/devicetree/bindings/sound/cs35l33.txt
new file mode 100644
index 000000000..dc5a355d1
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/cs35l33.txt
@@ -0,0 +1,124 @@
+CS35L33 Speaker Amplifier
+
+Required properties:
+
+ - compatible : "cirrus,cs35l33"
+
+ - reg : the I2C address of the device for I2C
+
+ - VA-supply, VP-supply : power supplies for the device,
+ as covered in
+ Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Optional properties:
+
+ - reset-gpios : gpio used to reset the amplifier
+
+ - interrupts : IRQ line info CS35L33.
+ (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+ for further information relating to interrupt properties)
+
+ - cirrus,boost-ctl : Booster voltage use to supply the amp. If the value is
+ 0, then VBST = VP. If greater than 0, the boost voltage will be 3300mV with
+ a value of 1 and will increase at a step size of 100mV until a maximum of
+ 8000mV.
+
+ - cirrus,ramp-rate : On power up, it affects the time from when the power
+ up sequence begins to the time the audio reaches a full-scale output.
+ On power down, it affects the time from when the power-down sequence
+ begins to when the amplifier disables the PWM outputs. If this property
+ is not set then soft ramping will be disabled and ramp time would be
+ 20ms. If this property is set to 0,1,2,3 then ramp times would be 40ms,
+ 60ms,100ms,175ms respectively for 48KHz sample rate.
+
+ - cirrus,boost-ipk : The maximum current allowed for the boost converter.
+ The range starts at 1850000uA and goes to a maximum of 3600000uA
+ with a step size of 15625uA. The default is 2500000uA.
+
+ - cirrus,imon-adc-scale : Configures the scaling of data bits from the IMON
+ ADC data word. This property can be set as a value of 0 for bits 15 down
+ to 0, 6 for 21 down to 6, 7, for 22 down to 7, 8 for 23 down to 8.
+
+
+Optional H/G Algorithm sub-node:
+
+The cs35l33 node can have a single "cirrus,hg-algo" sub-node that will enable
+the internal H/G Algorithm.
+
+ - cirrus,hg-algo : Sub-node for internal Class H/G algorithm that
+ controls the amplifier supplies.
+
+Optional properties for the "cirrus,hg-algo" sub-node:
+
+ - cirrus,mem-depth : Memory depth for the Class H/G algorithm measured in
+ LRCLK cycles. If this property is set to 0, 1, 2, or 3 then the memory
+ depths will be 1, 4, 8, 16 LRCLK cycles. The default is 16 LRCLK cycles.
+
+ cirrus,release-rate : The number of consecutive LRCLK periods before
+ allowing release condition tracking updates. The number of LRCLK periods
+ start at 3 to a maximum of 255.
+
+ - cirrus,ldo-thld : Configures the signal threshold at which the PWM output
+ stage enters LDO operation. Starts as a default value of 50mV for a value
+ of 1 and increases with a step size of 50mV to a maximum of 750mV (value of
+ 0xF).
+
+ - cirrus,ldo-path-disable : This is a boolean property. If present, the H/G
+ algorithm uses the max detection path. If not present, the LDO
+ detection path is used.
+
+ - cirrus,ldo-entry-delay : The LDO entry delay in milliseconds before the H/G
+ algorithm switches to the LDO voltage. This property can be set to values
+ from 0 to 7 for delays of 5ms, 10ms, 50ms, 100ms, 200ms, 500ms, 1000ms.
+ The default is 100ms.
+
+ - cirrus,vp-hg-auto : This is a boolean property. When set, class H/G VPhg
+ automatic updating is enabled.
+
+ - cirrus,vp-hg : Class H/G algorithm VPhg. Controls the H/G algorithm's
+ reference to the VP voltage for when to start generating a boosted VBST.
+ The reference voltage starts at 3000mV with a value of 0x3 and is increased
+ by 100mV per step to a maximum of 5500mV.
+
+ - cirrus,vp-hg-rate : The rate (number of LRCLK periods) at which the VPhg is
+ allowed to increase to a higher voltage when using VPhg automatic
+ tracking. This property can be set to values from 0 to 3 with rates of 128
+ periods, 2048 periods, 32768 periods, and 524288 periods.
+ The default is 32768 periods.
+
+ - cirrus,vp-hg-va : VA calculation reference for automatic VPhg tracking
+ using VPMON. This property can be set to values from 0 to 6 starting at
+ 1800mV with a step size of 50mV up to a maximum value of 1750mV.
+ Default is 1800mV.
+
+Example:
+
+cs35l33: cs35l33@40 {
+ compatible = "cirrus,cs35l33";
+ reg = <0x40>;
+
+ VA-supply = <&ldo5_reg>;
+ VP-supply = <&ldo5_reg>;
+
+ interrupt-parent = <&gpio8>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+ reset-gpios = <&cs47l91 34 0>;
+
+ cirrus,ramp-rate = <0x0>;
+ cirrus,boost-ctl = <0x30>; /* VBST = 8000mV */
+ cirrus,boost-ipk = <0xE0>; /* 3600mA */
+ cirrus,imon-adc-scale = <0> /* Bits 15 down to 0 */
+
+ cirrus,hg-algo {
+ cirrus,mem-depth = <0x3>;
+ cirrus,release-rate = <0x3>;
+ cirrus,ldo-thld = <0x1>;
+ cirrus,ldo-path-disable = <0x0>;
+ cirrus,ldo-entry-delay=<0x4>;
+ cirrus,vp-hg-auto;
+ cirrus,vp-hg=<0xF>;
+ cirrus,vp-hg-rate=<0x2>;
+ cirrus,vp-hg-va=<0x0>;
+ };
+};