diff options
Diffstat (limited to 'Documentation/devicetree/bindings/soundwire')
| -rw-r--r-- | Documentation/devicetree/bindings/soundwire/qcom,soundwire.yaml | 288 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/soundwire/soundwire-controller.yaml | 86 |
2 files changed, 374 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/soundwire/qcom,soundwire.yaml b/Documentation/devicetree/bindings/soundwire/qcom,soundwire.yaml new file mode 100644 index 0000000000..7d60a96549 --- /dev/null +++ b/Documentation/devicetree/bindings/soundwire/qcom,soundwire.yaml @@ -0,0 +1,288 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/soundwire/qcom,soundwire.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SoundWire Controller + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + - Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com> + +description: + The Qualcomm SoundWire controller along with its board specific bus parameters. + +properties: + compatible: + enum: + - qcom,soundwire-v1.3.0 + - qcom,soundwire-v1.5.0 + - qcom,soundwire-v1.5.1 + - qcom,soundwire-v1.6.0 + - qcom,soundwire-v1.7.0 + - qcom,soundwire-v2.0.0 + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + items: + - description: specify the SoundWire controller core. + - description: specify the Soundwire controller wake IRQ. + + interrupt-names: + minItems: 1 + items: + - const: core + - const: wakeup + + clocks: + items: + - description: iface clock + + clock-names: + items: + - const: iface + + resets: + items: + - description: SWR_AUDIO_CGCR RESET + + reset-names: + items: + - const: swr_audio_cgcr + + '#sound-dai-cells': + const: 1 + + '#address-cells': + const: 2 + + '#size-cells': + const: 0 + + wakeup-source: true + + qcom,din-ports: + $ref: /schemas/types.yaml#/definitions/uint32 + description: count of data in ports + + qcom,dout-ports: + $ref: /schemas/types.yaml#/definitions/uint32 + description: count of data out ports + + qcom,ports-word-length: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: + Size of payload channel sample. + Value of 0xff indicates that this option is not implemented + or applicable for the respective data port. + More info in MIPI Alliance SoundWire 1.0 Specifications. + minItems: 3 + maxItems: 16 + + qcom,ports-sinterval-low: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: + Sample interval (only lowest byte) of each data port. + Out ports followed by In ports. Used for Sample Interval calculation. + Value of 0xff indicates that this option is not implemented + or applicable for the respective data port. + More info in MIPI Alliance SoundWire 1.0 Specifications. + minItems: 3 + maxItems: 16 + + qcom,ports-sinterval: + $ref: /schemas/types.yaml#/definitions/uint16-array + description: + Sample interval of each data port. + Out ports followed by In ports. Used for Sample Interval calculation. + Value of 0xffff indicates that this option is not implemented + or applicable for the respective data port. + More info in MIPI Alliance SoundWire 1.0 Specifications. + minItems: 3 + maxItems: 16 + + qcom,ports-offset1: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: + Payload transport window offset1 of each data port. + Out ports followed by In ports. + Value of 0xff indicates that this option is not implemented + or applicable for the respective data port. + More info in MIPI Alliance SoundWire 1.0 Specifications. + minItems: 3 + maxItems: 16 + + qcom,ports-offset2: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: + Payload transport window offset2 of each data port. + Out ports followed by In ports. + Value of 0xff indicates that this option is not implemented + or applicable for the respective data port. + More info in MIPI Alliance SoundWire 1.0 Specifications. + minItems: 3 + maxItems: 16 + + qcom,ports-lane-control: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: + Identify which data lane the data port uses. + Out ports followed by In ports. + Value of 0xff indicates that this option is not implemented + or applicable for the respective data port. + More info in MIPI Alliance SoundWire 1.0 Specifications. + minItems: 3 + maxItems: 16 + + qcom,ports-block-pack-mode: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: + Indicate the block packing mode. + 0 to indicate Blocks are per Channel + 1 to indicate Blocks are per Port. + Out ports followed by In ports. + Value of 0xff indicates that this option is not implemented + or applicable for the respective data port. + More info in MIPI Alliance SoundWire 1.0 Specifications. + minItems: 3 + maxItems: 16 + items: + oneOf: + - minimum: 0 + maximum: 1 + - const: 0xff + + qcom,ports-hstart: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: + Identifying lowerst numbered column in SoundWire Frame, + i.e. left edge of the Transport sub-frame for each port. + Out ports followed by In ports. + Value of 0xff indicates that this option is not implemented + or applicable for the respective data port. + More info in MIPI Alliance SoundWire 1.0 Specifications. + minItems: 3 + maxItems: 16 + items: + oneOf: + - minimum: 0 + maximum: 15 + - const: 0xff + + qcom,ports-hstop: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: + Identifying highest numbered column in SoundWire Frame, + i.e. the right edge of the Transport + sub-frame for each port. Out ports followed by In ports. + Value of 0xff indicates that this option is not implemented + or applicable for the respective data port. + More info in MIPI Alliance SoundWire 1.0 Specifications. + minItems: 3 + maxItems: 16 + items: + oneOf: + - minimum: 0 + maximum: 15 + - const: 0xff + + qcom,ports-block-group-count: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: + In range 1 to 4 to indicate how many sample intervals are combined + into a payload. Out ports followed by In ports. + Value of 0xff indicates that this option is not implemented + or applicable for the respective data port. + More info in MIPI Alliance SoundWire 1.0 Specifications. + minItems: 3 + maxItems: 16 + items: + oneOf: + - minimum: 0 + maximum: 4 + - const: 0xff + + label: + maxItems: 1 + +patternProperties: + "^.*@[0-9a-f],[0-9a-f]$": + type: object + additionalProperties: true + description: + Child nodes for a standalone audio codec or speaker amplifier IC. + It has RX and TX Soundwire secondary devices. + properties: + compatible: + pattern: "^sdw[0-9a-f]{1}[0-9a-f]{4}[0-9a-f]{4}[0-9a-f]{2}$" + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - '#sound-dai-cells' + - '#address-cells' + - '#size-cells' + - qcom,dout-ports + - qcom,din-ports + - qcom,ports-offset1 + - qcom,ports-offset2 + +oneOf: + - required: + - qcom,ports-sinterval-low + - required: + - qcom,ports-sinterval + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/qcom,lpassaudiocc-sc7280.h> + + soundwire@3210000 { + compatible = "qcom,soundwire-v1.6.0"; + reg = <0x03210000 0x2000>; + + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 130 IRQ_TYPE_LEVEL_HIGH>; + + interrupt-names = "core", "wakeup"; + + clocks = <&lpass_rx_macro>; + clock-names = "iface"; + + qcom,din-ports = <0>; + qcom,dout-ports = <5>; + + resets = <&lpass_audiocc LPASS_AUDIO_SWR_RX_CGCR>; + reset-names = "swr_audio_cgcr"; + + qcom,ports-word-length = /bits/ 8 <0x01 0x07 0x04 0xff 0xff>; + qcom,ports-sinterval-low = /bits/ 8 <0x03 0x3f 0x1f 0x03 0x03>; + qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x0b 0x01 0x01>; + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x0b 0x00 0x00>; + qcom,ports-lane-control = /bits/ 8 <0x01 0x00 0x00 0x00 0x00>; + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0x00 0x01 0xff 0xff>; + qcom,ports-hstart = /bits/ 8 <0xff 0x03 0xff 0xff 0xff>; + qcom,ports-hstop = /bits/ 8 <0xff 0x06 0xff 0xff 0xff>; + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0x00>; + + #sound-dai-cells = <1>; + #address-cells = <2>; + #size-cells = <0>; + + codec@0,4 { + compatible = "sdw20217010d00"; + reg = <0 4>; + qcom,rx-port-mapping = <1 2 3 4 5>; + }; + }; diff --git a/Documentation/devicetree/bindings/soundwire/soundwire-controller.yaml b/Documentation/devicetree/bindings/soundwire/soundwire-controller.yaml new file mode 100644 index 0000000000..fdeb8af417 --- /dev/null +++ b/Documentation/devicetree/bindings/soundwire/soundwire-controller.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/soundwire/soundwire-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SoundWire Controller Common Properties + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + - Vinod Koul <vkoul@kernel.org> + +description: | + SoundWire busses can be described with a node for the SoundWire controller + device and a set of child nodes for each SoundWire slave on the bus. + +properties: + $nodename: + pattern: "^soundwire(@.*)?$" + + "#address-cells": + const: 2 + + "#size-cells": + const: 0 + +patternProperties: + "^.*@[0-9a-f],[0-9a-f]$": + type: object + + properties: + compatible: + pattern: "^sdw[0-9a-f]{1}[0-9a-f]{4}[0-9a-f]{4}[0-9a-f]{2}$" + description: Is the textual representation of SoundWire Enumeration + address. compatible string should contain SoundWire Version ID, + Manufacturer ID, Part ID and Class ID in order and shall be in + lower-case hexadecimal with leading zeroes. + Valid sizes of these fields are + Version ID is 1 nibble, number '0x1' represents SoundWire 1.0 + and '0x2' represents SoundWire 1.1 and so on. + MFD is 4 nibbles + PID is 4 nibbles + CID is 2 nibbles + More Information on detail of encoding of these fields can be + found in MIPI Alliance DisCo & SoundWire 1.0 Specifications. + + reg: + maxItems: 1 + description: + Link ID followed by Instance ID of SoundWire Device Address. + + required: + - compatible + - reg + +required: + - "#address-cells" + - "#size-cells" + +additionalProperties: true + +examples: + - | + soundwire@c2d0000 { + #address-cells = <2>; + #size-cells = <0>; + reg = <0x0c2d0000 0x2000>; + + speaker@0,1 { + compatible = "sdw10217201000"; + reg = <0 1>; + powerdown-gpios = <&wcdpinctrl 2 0>; + #thermal-sensor-cells = <0>; + #sound-dai-cells = <0>; + }; + + speaker@0,2 { + compatible = "sdw10217201000"; + reg = <0 2>; + powerdown-gpios = <&wcdpinctrl 2 0>; + #thermal-sensor-cells = <0>; + #sound-dai-cells = <0>; + }; + }; + +... |