diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml | 463 |
1 files changed, 463 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml new file mode 100644 index 0000000000..1394557517 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml @@ -0,0 +1,463 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/ci-hdrc-usb2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: USB2 ChipIdea USB controller + +maintainers: + - Xu Yang <xu.yang_2@nxp.com> + - Peng Fan <peng.fan@nxp.com> + +properties: + compatible: + oneOf: + - enum: + - chipidea,usb2 + - lsi,zevio-usb + - nvidia,tegra20-ehci + - nvidia,tegra20-udc + - nvidia,tegra30-ehci + - nvidia,tegra30-udc + - nvidia,tegra114-udc + - nvidia,tegra124-udc + - qcom,ci-hdrc + - items: + - enum: + - nvidia,tegra114-ehci + - nvidia,tegra124-ehci + - nvidia,tegra210-ehci + - const: nvidia,tegra30-ehci + - items: + - enum: + - fsl,imx23-usb + - fsl,imx25-usb + - fsl,imx28-usb + - fsl,imx35-usb + - fsl,imx50-usb + - fsl,imx51-usb + - fsl,imx53-usb + - fsl,imx6q-usb + - fsl,imx6sl-usb + - fsl,imx6sx-usb + - fsl,imx6ul-usb + - fsl,imx7d-usb + - fsl,vf610-usb + - const: fsl,imx27-usb + - items: + - enum: + - fsl,imx8dxl-usb + - fsl,imx8ulp-usb + - const: fsl,imx7ulp-usb + - const: fsl,imx6ul-usb + - items: + - enum: + - fsl,imx8mm-usb + - fsl,imx8mn-usb + - const: fsl,imx7d-usb + - const: fsl,imx27-usb + - items: + - enum: + - fsl,imx6sll-usb + - fsl,imx7ulp-usb + - const: fsl,imx6ul-usb + - const: fsl,imx27-usb + - items: + - const: xlnx,zynq-usb-2.20a + - const: chipidea,usb2 + + reg: + minItems: 1 + maxItems: 2 + + interrupts: + minItems: 1 + maxItems: 2 + + clocks: + minItems: 1 + maxItems: 3 + + clock-names: + minItems: 1 + maxItems: 3 + + dr_mode: true + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + reset-names: + maxItems: 1 + + "#reset-cells": + const: 1 + + phy_type: true + + itc-setting: + description: + interrupt threshold control register control, the setting should be + aligned with ITC bits at register USBCMD. + $ref: /schemas/types.yaml#/definitions/uint32 + + ahb-burst-config: + description: + it is vendor dependent, the required value should be aligned with + AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This property is + used to change AHB burst configuration, check the chipidea spec for + meaning of each value. If this property is not existed, it will use + the reset value. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0x7 + + tx-burst-size-dword: + description: + it is vendor dependent, the tx burst size in dword (4 bytes), This + register represents the maximum length of a the burst in 32-bit + words while moving data from system memory to the USB bus, the value + of this property will only take effect if property "ahb-burst-config" + is set to 0, if this property is missing the reset default of the + hardware implementation will be used. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0x20 + + rx-burst-size-dword: + description: + it is vendor dependent, the rx burst size in dword (4 bytes), This + register represents the maximum length of a the burst in 32-bit words + while moving data from the USB bus to system memory, the value of + this property will only take effect if property "ahb-burst-config" + is set to 0, if this property is missing the reset default of the + hardware implementation will be used. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0x20 + + extcon: + description: + Phandles to external connector devices. First phandle should point + to external connector, which provide "USB" cable events, the second + should point to external connector device, which provide "USB-HOST" + cable events. If one of the external connector devices is not + required, empty <0> phandle should be specified. + $ref: /schemas/types.yaml#/definitions/phandle-array + minItems: 1 + items: + - description: vbus extcon + - description: id extcon + + phy-clkgate-delay-us: + description: + The delay time (us) between putting the PHY into low power mode and + gating the PHY clock. + + non-zero-ttctrl-ttha: + description: + After setting this property, the value of register ttctrl.ttha + will be 0x7f; if not, the value will be 0x0, this is the default + value. It needs to be very carefully for setting this property, it + is recommended that consult with your IC engineer before setting + this value. On the most of chipidea platforms, the "usage_tt" flag + at RTL is 0, so this property only affects siTD. + + If this property is not set, the max packet size is 1023 bytes, and + if the total of packet size for previous transactions are more than + 256 bytes, it can't accept any transactions within this frame. The + use case is single transaction, but higher frame rate. + + If this property is set, the max packet size is 188 bytes, it can + handle more transactions than above case, it can accept transactions + until it considers the left room size within frame is less than 188 + bytes, software needs to make sure it does not send more than 90% + maximum_periodic_data_per_frame. The use case is multiple + transactions, but less frame rate. + type: boolean + + mux-controls: + description: + The mux control for toggling host/device output of this controller. + It's expected that a mux state of 0 indicates device mode and a mux + state of 1 indicates host mode. + maxItems: 1 + + mux-control-names: + const: usb_switch + + operating-points-v2: + description: A phandle to the OPP table containing the performance states. + $ref: /schemas/types.yaml#/definitions/phandle + + pinctrl-names: + description: + Names for optional pin modes in "default", "host", "device". + In case of HSIC-mode, "idle" and "active" pin modes are mandatory. + In this case, the "idle" state needs to pull down the data and + strobe pin and the "active" state needs to pull up the strobe pin. + oneOf: + - items: + - const: idle + - const: active + - items: + - const: default + - enum: + - host + - device + - items: + - const: default + + pinctrl-0: + maxItems: 1 + + pinctrl-1: + maxItems: 1 + + phys: + maxItems: 1 + + phy-names: + const: usb-phy + + phy-select: + description: + Phandler of TCSR node with two argument that indicate register + offset, and phy index + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - description: phandle to TCSR node + - description: register offset + - description: phy index + + vbus-supply: + description: reference to the VBUS regulator. + + fsl,usbmisc: + description: + Phandler of non-core register device, with one argument that + indicate usb controller index + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to usbmisc node + - description: index of usb controller + + fsl,anatop: + description: phandle for the anatop node. + $ref: /schemas/types.yaml#/definitions/phandle + + disable-over-current: + type: boolean + description: disable over current detect + + over-current-active-low: + type: boolean + description: over current signal polarity is active low + + over-current-active-high: + type: boolean + description: + Over current signal polarity is active high. It's recommended to + specify the over current polarity. + + power-active-high: + type: boolean + description: power signal polarity is active high + + external-vbus-divider: + type: boolean + description: enables off-chip resistor divider for Vbus + + samsung,picophy-pre-emp-curr-control: + description: + HS Transmitter Pre-Emphasis Current Control. This signal controls + the amount of current sourced to the USB_OTG*_DP and USB_OTG*_DN + pins after a J-to-K or K-to-J transition. The range is from 0x0 to + 0x3, the default value is 0x1. Details can refer to TXPREEMPAMPTUNE0 + bits of USBNC_n_PHY_CFG1. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0x3 + + samsung,picophy-dc-vol-level-adjust: + description: + HS DC Voltage Level Adjustment. Adjust the high-speed transmitter DC + level voltage. The range is from 0x0 to 0xf, the default value is + 0x3. Details can refer to TXVREFTUNE0 bits of USBNC_n_PHY_CFG1. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0xf + + fsl,picophy-rise-fall-time-adjust: + description: + HS Transmitter Rise/Fall Time Adjustment. Adjust the rise/fall times + of the high-speed transmitter waveform. It has no unit. The rise/fall + time will be increased or decreased by a certain percentage relative + to design default time. (0:-10%; 1:design default; 2:+15%; 3:+20%) + Details can refer to TXRISETUNE0 bit of USBNC_n_PHY_CFG1. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + default: 1 + + usb-phy: + description: phandle for the PHY device. Use "phys" instead. + $ref: /schemas/types.yaml#/definitions/phandle + deprecated: true + + fsl,usbphy: + description: phandle of usb phy that connects to the port. Use "phys" instead. + $ref: /schemas/types.yaml#/definitions/phandle + deprecated: true + + nvidia,phy: + description: phandle of usb phy that connects to the port. Use "phys" instead. + $ref: /schemas/types.yaml#/definitions/phandle + deprecated: true + + nvidia,needs-double-reset: + description: Indicates double reset or not. + type: boolean + deprecated: true + + port: + description: + Any connector to the data bus of this controller should be modelled + using the OF graph bindings specified, if the "usb-role-switch" + property is used. + $ref: /schemas/graph.yaml#/properties/port + + reset-gpios: + maxItems: 1 + + ulpi: + type: object + additionalProperties: false + patternProperties: + "^phy(-[0-9])?$": + description: The phy child node for Qcom chips. + type: object + $ref: /schemas/phy/qcom,usb-hs-phy.yaml + +dependencies: + port: [ usb-role-switch ] + mux-controls: [ mux-control-names ] + +required: + - compatible + - reg + - interrupts + +allOf: + - $ref: usb-hcd.yaml# + - $ref: usb-drd.yaml# + - if: + properties: + phy_type: + const: hsic + required: + - phy_type + then: + properties: + pinctrl-names: + items: + - const: idle + - const: active + else: + properties: + pinctrl-names: + minItems: 1 + maxItems: 2 + oneOf: + - items: + - const: default + - enum: + - host + - device + - items: + - const: default + - if: + properties: + compatible: + contains: + enum: + - chipidea,usb2 + - lsi,zevio-usb + - nvidia,tegra20-udc + - nvidia,tegra30-udc + - nvidia,tegra114-udc + - nvidia,tegra124-udc + - qcom,ci-hdrc + - xlnx,zynq-usb-2.20a + then: + properties: + fsl,usbmisc: false + disable-over-current: false + over-current-active-low: false + over-current-active-high: false + power-active-high: false + external-vbus-divider: false + samsung,picophy-pre-emp-curr-control: false + samsung,picophy-dc-vol-level-adjust: false + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/berlin2.h> + + usb@f7ed0000 { + compatible = "chipidea,usb2"; + reg = <0xf7ed0000 0x10000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&chip CLKID_USB0>; + phys = <&usb_phy0>; + phy-names = "usb-phy"; + vbus-supply = <®_usb0_vbus>; + itc-setting = <0x4>; /* 4 micro-frames */ + /* Incremental burst of unspecified length */ + ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; /* 64 bytes */ + rx-burst-size-dword = <0x10>; + extcon = <0>, <&usb_id>; + phy-clkgate-delay-us = <400>; + mux-controls = <&usb_switch>; + mux-control-names = "usb_switch"; + }; + + # Example for HSIC: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/imx6qdl-clock.h> + + usb@2184400 { + compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + reg = <0x02184400 0x200>; + interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_USBOH3>; + fsl,usbphy = <&usbphynop1>; + fsl,usbmisc = <&usbmisc 2>; + phy_type = "hsic"; + dr_mode = "host"; + ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; + pinctrl-names = "idle", "active"; + pinctrl-0 = <&pinctrl_usbh2_idle>; + pinctrl-1 = <&pinctrl_usbh2_active>; + #address-cells = <1>; + #size-cells = <0>; + + ethernet@1 { + compatible = "usb424,9730"; + reg = <1>; + }; + }; + +... |