diff options
Diffstat (limited to 'Documentation/hwmon/sht3x.rst')
| -rw-r--r-- | Documentation/hwmon/sht3x.rst | 88 |
1 files changed, 88 insertions, 0 deletions
diff --git a/Documentation/hwmon/sht3x.rst b/Documentation/hwmon/sht3x.rst new file mode 100644 index 0000000000..87864ffd17 --- /dev/null +++ b/Documentation/hwmon/sht3x.rst @@ -0,0 +1,88 @@ +Kernel driver sht3x +=================== + +Supported chips: + + * Sensirion SHT3x-DIS + + Prefix: 'sht3x' + + Addresses scanned: none + + Datasheet: https://www.sensirion.com/file/datasheet_sht3x_digital + +Author: + + - David Frey <david.frey@sensirion.com> + - Pascal Sachs <pascal.sachs@sensirion.com> + +Description +----------- + +This driver implements support for the Sensirion SHT3x-DIS chip, a humidity +and temperature sensor. Temperature is measured in degrees celsius, relative +humidity is expressed as a percentage. In the sysfs interface, all values are +scaled by 1000, i.e. the value for 31.5 degrees celsius is 31500. + +The device communicates with the I2C protocol. Sensors can have the I2C +addresses 0x44 or 0x45, depending on the wiring. See +Documentation/i2c/instantiating-devices.rst for methods to instantiate the device. + +Even if sht3x sensor supports clock-strech(blocking mode) and non-strench +(non-blocking mode) in single-shot mode, this driver only supports the latter. + +The sht3x sensor supports a single shot mode as well as 5 periodic measure +modes, which can be controlled with the update_interval sysfs interface. +The allowed update_interval in milliseconds are as follows: + + ===== ======= ==================== + 0 single shot mode + 2000 0.5 Hz periodic measurement + 1000 1 Hz periodic measurement + 500 2 Hz periodic measurement + 250 4 Hz periodic measurement + 100 10 Hz periodic measurement + ===== ======= ==================== + +In the periodic measure mode, the sensor automatically triggers a measurement +with the configured update interval on the chip. When a temperature or humidity +reading exceeds the configured limits, the alert attribute is set to 1 and +the alert pin on the sensor is set to high. +When the temperature and humidity readings move back between the hysteresis +values, the alert bit is set to 0 and the alert pin on the sensor is set to +low. + +sysfs-Interface +--------------- + +=================== ============================================================ +temp1_input: temperature input +humidity1_input: humidity input +temp1_max: temperature max value +temp1_max_hyst: temperature hysteresis value for max limit +humidity1_max: humidity max value +humidity1_max_hyst: humidity hysteresis value for max limit +temp1_min: temperature min value +temp1_min_hyst: temperature hysteresis value for min limit +humidity1_min: humidity min value +humidity1_min_hyst: humidity hysteresis value for min limit +temp1_alarm: alarm flag is set to 1 if the temperature is outside the + configured limits. Alarm only works in periodic measure mode +humidity1_alarm: alarm flag is set to 1 if the humidity is outside the + configured limits. Alarm only works in periodic measure mode +heater_enable: heater enable, heating element removes excess humidity from + sensor: + + - 0: turned off + - 1: turned on +update_interval: update interval, 0 for single shot, interval in msec + for periodic measurement. If the interval is not supported + by the sensor, the next faster interval is chosen +repeatability: write or read repeatability, higher repeatability means + longer measurement duration, lower noise level and + larger energy consumption: + + - 0: low repeatability + - 1: medium repeatability + - 2: high repeatability +=================== ============================================================ |