diff options
Diffstat (limited to 'Documentation/networking/device_drivers')
87 files changed, 20104 insertions, 0 deletions
diff --git a/Documentation/networking/device_drivers/appletalk/cops.rst b/Documentation/networking/device_drivers/appletalk/cops.rst new file mode 100644 index 0000000000..964ba80599 --- /dev/null +++ b/Documentation/networking/device_drivers/appletalk/cops.rst @@ -0,0 +1,80 @@ +.. SPDX-License-Identifier: GPL-2.0 + +======================================== +The COPS LocalTalk Linux driver (cops.c) +======================================== + +By Jay Schulist <jschlst@samba.org> + +This driver has two modes and they are: Dayna mode and Tangent mode. +Each mode corresponds with the type of card. It has been found +that there are 2 main types of cards and all other cards are +the same and just have different names or only have minor differences +such as more IO ports. As this driver is tested it will +become more clear exactly what cards are supported. + +Right now these cards are known to work with the COPS driver. The +LT-200 cards work in a somewhat more limited capacity than the +DL200 cards, which work very well and are in use by many people. + +TANGENT driver mode: + - Tangent ATB-II, Novell NL-1000, Daystar Digital LT-200 + +DAYNA driver mode: + - Dayna DL2000/DaynaTalk PC (Half Length), COPS LT-95, + - Farallon PhoneNET PC III, Farallon PhoneNET PC II + +Other cards possibly supported mode unknown though: + - Dayna DL2000 (Full length) + +The COPS driver defaults to using Dayna mode. To change the driver's +mode if you built a driver with dual support use board_type=1 or +board_type=2 for Dayna or Tangent with insmod. + +Operation/loading of the driver +=============================== + +Use modprobe like this: /sbin/modprobe cops.o (IO #) (IRQ #) +If you do not specify any options the driver will try and use the IO = 0x240, +IRQ = 5. As of right now I would only use IRQ 5 for the card, if autoprobing. + +To load multiple COPS driver Localtalk cards you can do one of the following:: + + insmod cops io=0x240 irq=5 + insmod -o cops2 cops io=0x260 irq=3 + +Or in lilo.conf put something like this:: + + append="ether=5,0x240,lt0 ether=3,0x260,lt1" + +Then bring up the interface with ifconfig. It will look something like this:: + + lt0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-F7-00-00-00-00-00-00-00-00 + inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 + UP BROADCAST RUNNING NOARP MULTICAST MTU:600 Metric:1 + RX packets:0 errors:0 dropped:0 overruns:0 frame:0 + TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 coll:0 + +Netatalk Configuration +====================== + +You will need to configure atalkd with something like the following to make +it work with the cops.c driver. + +* For single LTalk card use:: + + dummy -seed -phase 2 -net 2000 -addr 2000.10 -zone "1033" + lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033" + +* For multiple cards, Ethernet and LocalTalk:: + + eth0 -seed -phase 2 -net 3000 -addr 3000.20 -zone "1033" + lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033" + +* For multiple LocalTalk cards, and an Ethernet card. + +* Order seems to matter here, Ethernet last:: + + lt0 -seed -phase 1 -net 1000 -addr 1000.10 -zone "LocalTalk1" + lt1 -seed -phase 1 -net 2000 -addr 2000.20 -zone "LocalTalk2" + eth0 -seed -phase 2 -net 3000 -addr 3000.30 -zone "EtherTalk" diff --git a/Documentation/networking/device_drivers/appletalk/index.rst b/Documentation/networking/device_drivers/appletalk/index.rst new file mode 100644 index 0000000000..c196baeb08 --- /dev/null +++ b/Documentation/networking/device_drivers/appletalk/index.rst @@ -0,0 +1,18 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) + +AppleTalk Device Drivers +======================== + +Contents: + +.. toctree:: + :maxdepth: 2 + + cops + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/atm/cxacru-cf.py b/Documentation/networking/device_drivers/atm/cxacru-cf.py new file mode 100644 index 0000000000..b41d298398 --- /dev/null +++ b/Documentation/networking/device_drivers/atm/cxacru-cf.py @@ -0,0 +1,48 @@ +#!/usr/bin/env python +# Copyright 2009 Simon Arlott +# +# This program is free software; you can redistribute it and/or modify it +# under the terms of the GNU General Public License as published by the Free +# Software Foundation; either version 2 of the License, or (at your option) +# any later version. +# +# This program is distributed in the hope that it will be useful, but WITHOUT +# ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or +# FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for +# more details. +# +# You should have received a copy of the GNU General Public License along with +# this program; if not, write to the Free Software Foundation, Inc., 59 +# Temple Place - Suite 330, Boston, MA 02111-1307, USA. +# +# Usage: cxacru-cf.py < cxacru-cf.bin +# Output: values string suitable for the sysfs adsl_config attribute +# +# Warning: cxacru-cf.bin with MD5 hash cdbac2689969d5ed5d4850f117702110 +# contains mis-aligned values which will stop the modem from being able +# to make a connection. If the first and last two bytes are removed then +# the values become valid, but the modulation will be forced to ANSI +# T1.413 only which may not be appropriate. +# +# The original binary format is a packed list of le32 values. + +import sys +import struct + +i = 0 +while True: + buf = sys.stdin.read(4) + + if len(buf) == 0: + break + elif len(buf) != 4: + sys.stdout.write("\n") + sys.stderr.write("Error: read {0} not 4 bytes\n".format(len(buf))) + sys.exit(1) + + if i > 0: + sys.stdout.write(" ") + sys.stdout.write("{0:x}={1}".format(i, struct.unpack("<I", buf)[0])) + i += 1 + +sys.stdout.write("\n") diff --git a/Documentation/networking/device_drivers/atm/cxacru.rst b/Documentation/networking/device_drivers/atm/cxacru.rst new file mode 100644 index 0000000000..6088af2ffe --- /dev/null +++ b/Documentation/networking/device_drivers/atm/cxacru.rst @@ -0,0 +1,120 @@ +.. SPDX-License-Identifier: GPL-2.0 + +======================== +ATM cxacru device driver +======================== + +Firmware is required for this device: http://accessrunner.sourceforge.net/ + +While it is capable of managing/maintaining the ADSL connection without the +module loaded, the device will sometimes stop responding after unloading the +driver and it is necessary to unplug/remove power to the device to fix this. + +Note: support for cxacru-cf.bin has been removed. It was not loaded correctly +so it had no effect on the device configuration. Fixing it could have stopped +existing devices working when an invalid configuration is supplied. + +There is a script cxacru-cf.py to convert an existing file to the sysfs form. + +Detected devices will appear as ATM devices named "cxacru". In /sys/class/atm/ +these are directories named cxacruN where N is the device number. A symlink +named device points to the USB interface device's directory which contains +several sysfs attribute files for retrieving device statistics: + +* adsl_controller_version + +* adsl_headend +* adsl_headend_environment + + - Information about the remote headend. + +* adsl_config + + - Configuration writing interface. + - Write parameters in hexadecimal format <index>=<value>, + separated by whitespace, e.g.: + + "1=0 a=5" + + - Up to 7 parameters at a time will be sent and the modem will restart + the ADSL connection when any value is set. These are logged for future + reference. + +* downstream_attenuation (dB) +* downstream_bits_per_frame +* downstream_rate (kbps) +* downstream_snr_margin (dB) + + - Downstream stats. + +* upstream_attenuation (dB) +* upstream_bits_per_frame +* upstream_rate (kbps) +* upstream_snr_margin (dB) +* transmitter_power (dBm/Hz) + + - Upstream stats. + +* downstream_crc_errors +* downstream_fec_errors +* downstream_hec_errors +* upstream_crc_errors +* upstream_fec_errors +* upstream_hec_errors + + - Error counts. + +* line_startable + + - Indicates that ADSL support on the device + is/can be enabled, see adsl_start. + +* line_status + + - "initialising" + - "down" + - "attempting to activate" + - "training" + - "channel analysis" + - "exchange" + - "waiting" + - "up" + + Changes between "down" and "attempting to activate" + if there is no signal. + +* link_status + + - "not connected" + - "connected" + - "lost" + +* mac_address + +* modulation + + - "" (when not connected) + - "ANSI T1.413" + - "ITU-T G.992.1 (G.DMT)" + - "ITU-T G.992.2 (G.LITE)" + +* startup_attempts + + - Count of total attempts to initialise ADSL. + +To enable/disable ADSL, the following can be written to the adsl_state file: + + - "start" + - "stop + - "restart" (stops, waits 1.5s, then starts) + - "poll" (used to resume status polling if it was disabled due to failure) + +Changes in adsl/line state are reported via kernel log messages:: + + [4942145.150704] ATM dev 0: ADSL state: running + [4942243.663766] ATM dev 0: ADSL line: down + [4942249.665075] ATM dev 0: ADSL line: attempting to activate + [4942253.654954] ATM dev 0: ADSL line: training + [4942255.666387] ATM dev 0: ADSL line: channel analysis + [4942259.656262] ATM dev 0: ADSL line: exchange + [2635357.696901] ATM dev 0: ADSL line: up (8128 kb/s down | 832 kb/s up) diff --git a/Documentation/networking/device_drivers/atm/fore200e.rst b/Documentation/networking/device_drivers/atm/fore200e.rst new file mode 100644 index 0000000000..55df9ec09a --- /dev/null +++ b/Documentation/networking/device_drivers/atm/fore200e.rst @@ -0,0 +1,66 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============================================= +FORE Systems PCA-200E/SBA-200E ATM NIC driver +============================================= + +This driver adds support for the FORE Systems 200E-series ATM adapters +to the Linux operating system. It is based on the earlier PCA-200E driver +written by Uwe Dannowski. + +The driver simultaneously supports PCA-200E and SBA-200E adapters on +i386, alpha (untested), powerpc, sparc and sparc64 archs. + +The intent is to enable the use of different models of FORE adapters at the +same time, by hosts that have several bus interfaces (such as PCI+SBUS, +or PCI+EISA). + +Only PCI and SBUS devices are currently supported by the driver, but support +for other bus interfaces such as EISA should not be too hard to add. + + +Firmware Copyright Notice +------------------------- + +Please read the fore200e_firmware_copyright file present +in the linux/drivers/atm directory for details and restrictions. + + +Firmware Updates +---------------- + +The FORE Systems 200E-series driver is shipped with firmware data being +uploaded to the ATM adapters at system boot time or at module loading time. +The supplied firmware images should work with all adapters. + +However, if you encounter problems (the firmware doesn't start or the driver +is unable to read the PROM data), you may consider trying another firmware +version. Alternative binary firmware images can be found somewhere on the +ForeThought CD-ROM supplied with your adapter by FORE Systems. + +You can also get the latest firmware images from FORE Systems at +https://en.wikipedia.org/wiki/FORE_Systems. Register TACTics Online and go to +the 'software updates' pages. The firmware binaries are part of +the various ForeThought software distributions. + +Notice that different versions of the PCA-200E firmware exist, depending +on the endianness of the host architecture. The driver is shipped with +both little and big endian PCA firmware images. + +Name and location of the new firmware images can be set at kernel +configuration time: + +1. Copy the new firmware binary files (with .bin, .bin1 or .bin2 suffix) + to some directory, such as linux/drivers/atm. + +2. Reconfigure your kernel to set the new firmware name and location. + Expected pathnames are absolute or relative to the drivers/atm directory. + +3. Rebuild and re-install your kernel or your module. + + +Feedback +-------- + +Feedback is welcome. Please send success stories/bug reports/ +patches/improvement/comments/flames to <lizzi@cnam.fr>. diff --git a/Documentation/networking/device_drivers/atm/index.rst b/Documentation/networking/device_drivers/atm/index.rst new file mode 100644 index 0000000000..7b593f031a --- /dev/null +++ b/Documentation/networking/device_drivers/atm/index.rst @@ -0,0 +1,20 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) + +Asynchronous Transfer Mode (ATM) Device Drivers +=============================================== + +Contents: + +.. toctree:: + :maxdepth: 2 + + cxacru + fore200e + iphase + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/atm/iphase.rst b/Documentation/networking/device_drivers/atm/iphase.rst new file mode 100644 index 0000000000..388c7101e2 --- /dev/null +++ b/Documentation/networking/device_drivers/atm/iphase.rst @@ -0,0 +1,193 @@ +.. SPDX-License-Identifier: GPL-2.0 + +================================== +ATM (i)Chip IA Linux Driver Source +================================== + + READ ME FIRST + +-------------------------------------------------------------------------------- + + Read This Before You Begin! + +-------------------------------------------------------------------------------- + +Description +=========== + +This is the README file for the Interphase PCI ATM (i)Chip IA Linux driver +source release. + +The features and limitations of this driver are as follows: + + - A single VPI (VPI value of 0) is supported. + - Supports 4K VCs for the server board (with 512K control memory) and 1K + VCs for the client board (with 128K control memory). + - UBR, ABR and CBR service categories are supported. + - Only AAL5 is supported. + - Supports setting of PCR on the VCs. + - Multiple adapters in a system are supported. + - All variants of Interphase ATM PCI (i)Chip adapter cards are supported, + including x575 (OC3, control memory 128K , 512K and packet memory 128K, + 512K and 1M), x525 (UTP25) and x531 (DS3 and E3). See + http://www.iphase.com/ + for details. + - Only x86 platforms are supported. + - SMP is supported. + + +Before You Start +================ + + +Installation +------------ + +1. Installing the adapters in the system + + To install the ATM adapters in the system, follow the steps below. + + a. Login as root. + b. Shut down the system and power off the system. + c. Install one or more ATM adapters in the system. + d. Connect each adapter to a port on an ATM switch. The green 'Link' + LED on the front panel of the adapter will be on if the adapter is + connected to the switch properly when the system is powered up. + e. Power on and boot the system. + +2. [ Removed ] + +3. Rebuild kernel with ABR support + + [ a. and b. removed ] + + c. Reconfigure the kernel, choose the Interphase ia driver through "make + menuconfig" or "make xconfig". + d. Rebuild the kernel, loadable modules and the atm tools. + e. Install the new built kernel and modules and reboot. + +4. Load the adapter hardware driver (ia driver) if it is built as a module + + a. Login as root. + b. Change directory to /lib/modules/<kernel-version>/atm. + c. Run "insmod suni.o;insmod iphase.o" + The yellow 'status' LED on the front panel of the adapter will blink + while the driver is loaded in the system. + d. To verify that the 'ia' driver is loaded successfully, run the + following command:: + + cat /proc/atm/devices + + If the driver is loaded successfully, the output of the command will + be similar to the following lines:: + + Itf Type ESI/"MAC"addr AAL(TX,err,RX,err,drop) ... + 0 ia xxxxxxxxx 0 ( 0 0 0 0 0 ) 5 ( 0 0 0 0 0 ) + + You can also check the system log file /var/log/messages for messages + related to the ATM driver. + +5. Ia Driver Configuration + +5.1 Configuration of adapter buffers + The (i)Chip boards have 3 different packet RAM size variants: 128K, 512K and + 1M. The RAM size decides the number of buffers and buffer size. The default + size and number of buffers are set as following: + + ========= ======= ====== ====== ====== ====== ====== + Total Rx RAM Tx RAM Rx Buf Tx Buf Rx buf Tx buf + RAM size size size size size cnt cnt + ========= ======= ====== ====== ====== ====== ====== + 128K 64K 64K 10K 10K 6 6 + 512K 256K 256K 10K 10K 25 25 + 1M 512K 512K 10K 10K 51 51 + ========= ======= ====== ====== ====== ====== ====== + + These setting should work well in most environments, but can be + changed by typing the following command:: + + insmod <IA_DIR>/ia.o IA_RX_BUF=<RX_CNT> IA_RX_BUF_SZ=<RX_SIZE> \ + IA_TX_BUF=<TX_CNT> IA_TX_BUF_SZ=<TX_SIZE> + + Where: + + - RX_CNT = number of receive buffers in the range (1-128) + - RX_SIZE = size of receive buffers in the range (48-64K) + - TX_CNT = number of transmit buffers in the range (1-128) + - TX_SIZE = size of transmit buffers in the range (48-64K) + + 1. Transmit and receive buffer size must be a multiple of 4. + 2. Care should be taken so that the memory required for the + transmit and receive buffers is less than or equal to the + total adapter packet memory. + +5.2 Turn on ia debug trace + + When the ia driver is built with the CONFIG_ATM_IA_DEBUG flag, the driver + can provide more debug trace if needed. There is a bit mask variable, + IADebugFlag, which controls the output of the traces. You can find the bit + map of the IADebugFlag in iphase.h. + The debug trace can be turn on through the insmod command line option, for + example, "insmod iphase.o IADebugFlag=0xffffffff" can turn on all the debug + traces together with loading the driver. + +6. Ia Driver Test Using ttcp_atm and PVC + + For the PVC setup, the test machines can either be connected back-to-back or + through a switch. If connected through the switch, the switch must be + configured for the PVC(s). + + a. For UBR test: + + At the test machine intended to receive data, type:: + + ttcp_atm -r -a -s 0.100 + + At the other test machine, type:: + + ttcp_atm -t -a -s 0.100 -n 10000 + + Run "ttcp_atm -h" to display more options of the ttcp_atm tool. + b. For ABR test: + + It is the same as the UBR testing, but with an extra command option:: + + -Pabr:max_pcr=<xxx> + + where: + + xxx = the maximum peak cell rate, from 170 - 353207. + + This option must be set on both the machines. + + c. For CBR test: + + It is the same as the UBR testing, but with an extra command option:: + + -Pcbr:max_pcr=<xxx> + + where: + + xxx = the maximum peak cell rate, from 170 - 353207. + + This option may only be set on the transmit machine. + + +Outstanding Issues +================== + + + +Contact Information +------------------- + +:: + + Customer Support: + United States: Telephone: (214) 654-5555 + Fax: (214) 654-5500 + E-Mail: intouch@iphase.com + Europe: Telephone: 33 (0)1 41 15 44 00 + Fax: 33 (0)1 41 15 12 13 + World Wide Web: http://www.iphase.com + Anonymous FTP: ftp.iphase.com diff --git a/Documentation/networking/device_drivers/cable/index.rst b/Documentation/networking/device_drivers/cable/index.rst new file mode 100644 index 0000000000..cce3c43929 --- /dev/null +++ b/Documentation/networking/device_drivers/cable/index.rst @@ -0,0 +1,18 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) + +Cable Modem Device Drivers +========================== + +Contents: + +.. toctree:: + :maxdepth: 2 + + sb1000 + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/cable/sb1000.rst b/Documentation/networking/device_drivers/cable/sb1000.rst new file mode 100644 index 0000000000..c8582ca403 --- /dev/null +++ b/Documentation/networking/device_drivers/cable/sb1000.rst @@ -0,0 +1,222 @@ +.. SPDX-License-Identifier: GPL-2.0 + +=================== +SB100 device driver +=================== + +sb1000 is a module network device driver for the General Instrument (also known +as NextLevel) SURFboard1000 internal cable modem board. This is an ISA card +which is used by a number of cable TV companies to provide cable modem access. +It's a one-way downstream-only cable modem, meaning that your upstream net link +is provided by your regular phone modem. + +This driver was written by Franco Venturi <fventuri@mediaone.net>. He deserves +a great deal of thanks for this wonderful piece of code! + +Needed tools +============ + +Support for this device is now a part of the standard Linux kernel. The +driver source code file is drivers/net/sb1000.c. In addition to this +you will need: + +1. The "cmconfig" program. This is a utility which supplements "ifconfig" + to configure the cable modem and network interface (usually called "cm0"); + +2. Several PPP scripts which live in /etc/ppp to make connecting via your + cable modem easy. + + These utilities can be obtained from: + + http://www.jacksonville.net/~fventuri/ + + in Franco's original source code distribution .tar.gz file. Support for + the sb1000 driver can be found at: + + - http://web.archive.org/web/%2E/http://home.adelphia.net/~siglercm/sb1000.html + - http://web.archive.org/web/%2E/http://linuxpower.cx/~cable/ + + along with these utilities. + +3. The standard isapnp tools. These are necessary to configure your SB1000 + card at boot time (or afterwards by hand) since it's a PnP card. + + If you don't have these installed as a standard part of your Linux + distribution, you can find them at: + + http://www.roestock.demon.co.uk/isapnptools/ + + or check your Linux distribution binary CD or their web site. For help with + isapnp, pnpdump, or /etc/isapnp.conf, go to: + + http://www.roestock.demon.co.uk/isapnptools/isapnpfaq.html + +Using the driver +================ + +To make the SB1000 card work, follow these steps: + +1. Run ``make config``, or ``make menuconfig``, or ``make xconfig``, whichever + you prefer, in the top kernel tree directory to set up your kernel + configuration. Make sure to say "Y" to "Prompt for development drivers" + and to say "M" to the sb1000 driver. Also say "Y" or "M" to all the standard + networking questions to get TCP/IP and PPP networking support. + +2. **BEFORE** you build the kernel, edit drivers/net/sb1000.c. Make sure + to redefine the value of READ_DATA_PORT to match the I/O address used + by isapnp to access your PnP cards. This is the value of READPORT in + /etc/isapnp.conf or given by the output of pnpdump. + +3. Build and install the kernel and modules as usual. + +4. Boot your new kernel following the usual procedures. + +5. Set up to configure the new SB1000 PnP card by capturing the output + of "pnpdump" to a file and editing this file to set the correct I/O ports, + IRQ, and DMA settings for all your PnP cards. Make sure none of the settings + conflict with one another. Then test this configuration by running the + "isapnp" command with your new config file as the input. Check for + errors and fix as necessary. (As an aside, I use I/O ports 0x110 and + 0x310 and IRQ 11 for my SB1000 card and these work well for me. YMMV.) + Then save the finished config file as /etc/isapnp.conf for proper + configuration on subsequent reboots. + +6. Download the original file sb1000-1.1.2.tar.gz from Franco's site or one of + the others referenced above. As root, unpack it into a temporary directory + and do a ``make cmconfig`` and then ``install -c cmconfig /usr/local/sbin``. + Don't do ``make install`` because it expects to find all the utilities built + and ready for installation, not just cmconfig. + +7. As root, copy all the files under the ppp/ subdirectory in Franco's + tar file into /etc/ppp, being careful not to overwrite any files that are + already in there. Then modify ppp@gi-on to set the correct login name, + phone number, and frequency for the cable modem. Also edit pap-secrets + to specify your login name and password and any site-specific information + you need. + +8. Be sure to modify /etc/ppp/firewall to use ipchains instead of + the older ipfwadm commands from the 2.0.x kernels. There's a neat utility to + convert ipfwadm commands to ipchains commands: + + http://users.dhp.com/~whisper/ipfwadm2ipchains/ + + You may also wish to modify the firewall script to implement a different + firewalling scheme. + +9. Start the PPP connection via the script /etc/ppp/ppp@gi-on. You must be + root to do this. It's better to use a utility like sudo to execute + frequently used commands like this with root permissions if possible. If you + connect successfully the cable modem interface will come up and you'll see a + driver message like this at the console:: + + cm0: sb1000 at (0x110,0x310), csn 1, S/N 0x2a0d16d8, IRQ 11. + sb1000.c:v1.1.2 6/01/98 (fventuri@mediaone.net) + + The "ifconfig" command should show two new interfaces, ppp0 and cm0. + + The command "cmconfig cm0" will give you information about the cable modem + interface. + +10. Try pinging a site via ``ping -c 5 www.yahoo.com``, for example. You should + see packets received. + +11. If you can't get site names (like www.yahoo.com) to resolve into + IP addresses (like 204.71.200.67), be sure your /etc/resolv.conf file + has no syntax errors and has the right nameserver IP addresses in it. + If this doesn't help, try something like ``ping -c 5 204.71.200.67`` to + see if the networking is running but the DNS resolution is where the + problem lies. + +12. If you still have problems, go to the support web sites mentioned above + and read the information and documentation there. + +Common problems +=============== + +1. Packets go out on the ppp0 interface but don't come back on the cm0 + interface. It looks like I'm connected but I can't even ping any + numerical IP addresses. (This happens predominantly on Debian systems due + to a default boot-time configuration script.) + +Solution + As root ``echo 0 > /proc/sys/net/ipv4/conf/cm0/rp_filter`` so it + can share the same IP address as the ppp0 interface. Note that this + command should probably be added to the /etc/ppp/cablemodem script + *right*between* the "/sbin/ifconfig" and "/sbin/cmconfig" commands. + You may need to do this to /proc/sys/net/ipv4/conf/ppp0/rp_filter as well. + If you do this to /proc/sys/net/ipv4/conf/default/rp_filter on each reboot + (in rc.local or some such) then any interfaces can share the same IP + addresses. + +2. I get "unresolved symbol" error messages on executing ``insmod sb1000.o``. + +Solution + You probably have a non-matching kernel source tree and + /usr/include/linux and /usr/include/asm header files. Make sure you + install the correct versions of the header files in these two directories. + Then rebuild and reinstall the kernel. + +3. When isapnp runs it reports an error, and my SB1000 card isn't working. + +Solution + There's a problem with later versions of isapnp using the "(CHECK)" + option in the lines that allocate the two I/O addresses for the SB1000 card. + This first popped up on RH 6.0. Delete "(CHECK)" for the SB1000 I/O addresses. + Make sure they don't conflict with any other pieces of hardware first! Then + rerun isapnp and go from there. + +4. I can't execute the /etc/ppp/ppp@gi-on file. + +Solution + As root do ``chmod ug+x /etc/ppp/ppp@gi-on``. + +5. The firewall script isn't working (with 2.2.x and higher kernels). + +Solution + Use the ipfwadm2ipchains script referenced above to convert the + /etc/ppp/firewall script from the deprecated ipfwadm commands to ipchains. + +6. I'm getting *tons* of firewall deny messages in the /var/kern.log, + /var/messages, and/or /var/syslog files, and they're filling up my /var + partition!!! + +Solution + First, tell your ISP that you're receiving DoS (Denial of Service) + and/or portscanning (UDP connection attempts) attacks! Look over the deny + messages to figure out what the attack is and where it's coming from. Next, + edit /etc/ppp/cablemodem and make sure the ",nobroadcast" option is turned on + to the "cmconfig" command (uncomment that line). If you're not receiving these + denied packets on your broadcast interface (IP address xxx.yyy.zzz.255 + typically), then someone is attacking your machine in particular. Be careful + out there.... + +7. Everything seems to work fine but my computer locks up after a while + (and typically during a lengthy download through the cable modem)! + +Solution + You may need to add a short delay in the driver to 'slow down' the + SURFboard because your PC might not be able to keep up with the transfer rate + of the SB1000. To do this, it's probably best to download Franco's + sb1000-1.1.2.tar.gz archive and build and install sb1000.o manually. You'll + want to edit the 'Makefile' and look for the 'SB1000_DELAY' + define. Uncomment those 'CFLAGS' lines (and comment out the default ones) + and try setting the delay to something like 60 microseconds with: + '-DSB1000_DELAY=60'. Then do ``make`` and as root ``make install`` and try + it out. If it still doesn't work or you like playing with the driver, you may + try other numbers. Remember though that the higher the delay, the slower the + driver (which slows down the rest of the PC too when it is actively + used). Thanks to Ed Daiga for this tip! + +Credits +======= + +This README came from Franco Venturi's original README file which is +still supplied with his driver .tar.gz archive. I and all other sb1000 users +owe Franco a tremendous "Thank you!" Additional thanks goes to Carl Patten +and Ralph Bonnell who are now managing the Linux SB1000 web site, and to +the SB1000 users who reported and helped debug the common problems listed +above. + + + Clemmitt Sigler + csigler@vt.edu diff --git a/Documentation/networking/device_drivers/can/can327.rst b/Documentation/networking/device_drivers/can/can327.rst new file mode 100644 index 0000000000..b87bfbe5d5 --- /dev/null +++ b/Documentation/networking/device_drivers/can/can327.rst @@ -0,0 +1,331 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) + +can327: ELM327 driver for Linux SocketCAN +========================================== + +Authors +-------- + +Max Staudt <max@enpas.org> + + + +Motivation +----------- + +This driver aims to lower the initial cost for hackers interested in +working with CAN buses. + +CAN adapters are expensive, few, and far between. +ELM327 interfaces are cheap and plentiful. +Let's use ELM327s as CAN adapters. + + + +Introduction +------------- + +This driver is an effort to turn abundant ELM327 based OBD interfaces +into full fledged (as far as possible) CAN interfaces. + +Since the ELM327 was never meant to be a stand alone CAN controller, +the driver has to switch between its modes as quickly as possible in +order to fake full-duplex operation. + +As such, can327 is a best effort driver. However, this is more than +enough to implement simple request-response protocols (such as OBD II), +and to monitor broadcast messages on a bus (such as in a vehicle). + +Most ELM327s come as nondescript serial devices, attached via USB or +Bluetooth. The driver cannot recognize them by itself, and as such it +is up to the user to attach it in form of a TTY line discipline +(similar to PPP, SLIP, slcan, ...). + +This driver is meant for ELM327 versions 1.4b and up, see below for +known limitations in older controllers and clones. + + + +Data sheet +----------- + +The official data sheets can be found at ELM electronics' home page: + + https://www.elmelectronics.com/ + + + +How to attach the line discipline +---------------------------------- + +Every ELM327 chip is factory programmed to operate at a serial setting +of 38400 baud/s, 8 data bits, no parity, 1 stopbit. + +If you have kept this default configuration, the line discipline can +be attached on a command prompt as follows:: + + sudo ldattach \ + --debug \ + --speed 38400 \ + --eightbits \ + --noparity \ + --onestopbit \ + --iflag -ICRNL,INLCR,-IXOFF \ + 30 \ + /dev/ttyUSB0 + +To change the ELM327's serial settings, please refer to its data +sheet. This needs to be done before attaching the line discipline. + +Once the ldisc is attached, the CAN interface starts out unconfigured. +Set the speed before starting it:: + + # The interface needs to be down to change parameters + sudo ip link set can0 down + sudo ip link set can0 type can bitrate 500000 + sudo ip link set can0 up + +500000 bit/s is a common rate for OBD-II diagnostics. +If you're connecting straight to a car's OBD port, this is the speed +that most cars (but not all!) expect. + +After this, you can set out as usual with candump, cansniffer, etc. + + + +How to check the controller version +------------------------------------ + +Use a terminal program to attach to the controller. + +After issuing the "``AT WS``" command, the controller will respond with +its version:: + + >AT WS + + + ELM327 v1.4b + + > + +Note that clones may claim to be any version they like. +It is not indicative of their actual feature set. + + + + +Communication example +---------------------- + +This is a short and incomplete introduction on how to talk to an ELM327. +It is here to guide understanding of the controller's and the driver's +limitation (listed below) as well as manual testing. + + +The ELM327 has two modes: + +- Command mode +- Reception mode + +In command mode, it expects one command per line, terminated by CR. +By default, the prompt is a "``>``", after which a command can be +entered:: + + >ATE1 + OK + > + +The init script in the driver switches off several configuration options +that are only meaningful in the original OBD scenario the chip is meant +for, and are actually a hindrance for can327. + + +When a command is not recognized, such as by an older version of the +ELM327, a question mark is printed as a response instead of OK:: + + >ATUNKNOWN + ? + > + +At present, can327 does not evaluate this response. See the section +below on known limitations for details. + + +When a CAN frame is to be sent, the target address is configured, after +which the frame is sent as a command that consists of the data's hex +dump:: + + >ATSH123 + OK + >DEADBEEF12345678 + OK + > + +The above interaction sends the SFF frame "``DE AD BE EF 12 34 56 78``" +with (11 bit) CAN ID ``0x123``. +For this to function, the controller must be configured for SFF sending +mode (using "``AT PB``", see code or datasheet). + + +Once a frame has been sent and wait-for-reply mode is on (``ATR1``, +configured on ``listen-only=off``), or when the reply timeout expires +and the driver sets the controller into monitoring mode (``ATMA``), +the ELM327 will send one line for each received CAN frame, consisting +of CAN ID, DLC, and data:: + + 123 8 DEADBEEF12345678 + +For EFF (29 bit) CAN frames, the address format is slightly different, +which can327 uses to tell the two apart:: + + 12 34 56 78 8 DEADBEEF12345678 + +The ELM327 will receive both SFF and EFF frames - the current CAN +config (``ATPB``) does not matter. + + +If the ELM327's internal UART sending buffer runs full, it will abort +the monitoring mode, print "BUFFER FULL" and drop back into command +mode. Note that in this case, unlike with other error messages, the +error message may appear on the same line as the last (usually +incomplete) data frame:: + + 12 34 56 78 8 DEADBEEF123 BUFFER FULL + + + +Known limitations of the controller +------------------------------------ + +- Clone devices ("v1.5" and others) + + Sending RTR frames is not supported and will be dropped silently. + + Receiving RTR with DLC 8 will appear to be a regular frame with + the last received frame's DLC and payload. + + "``AT CSM``" (CAN Silent Monitoring, i.e. don't send CAN ACKs) is + not supported, and is hard coded to ON. Thus, frames are not ACKed + while listening: "``AT MA``" (Monitor All) will always be "silent". + However, immediately after sending a frame, the ELM327 will be in + "receive reply" mode, in which it *does* ACK any received frames. + Once the bus goes silent, or an error occurs (such as BUFFER FULL), + or the receive reply timeout runs out, the ELM327 will end reply + reception mode on its own and can327 will fall back to "``AT MA``" + in order to keep monitoring the bus. + + Other limitations may apply, depending on the clone and the quality + of its firmware. + + +- All versions + + No full duplex operation is supported. The driver will switch + between input/output mode as quickly as possible. + + The length of outgoing RTR frames cannot be set. In fact, some + clones (tested with one identifying as "``v1.5``") are unable to + send RTR frames at all. + + We don't have a way to get real-time notifications on CAN errors. + While there is a command (``AT CS``) to retrieve some basic stats, + we don't poll it as it would force us to interrupt reception mode. + + +- Versions prior to 1.4b + + These versions do not send CAN ACKs when in monitoring mode (AT MA). + However, they do send ACKs while waiting for a reply immediately + after sending a frame. The driver maximizes this time to make the + controller as useful as possible. + + Starting with version 1.4b, the ELM327 supports the "``AT CSM``" + command, and the "listen-only" CAN option will take effect. + + +- Versions prior to 1.4 + + These chips do not support the "``AT PB``" command, and thus cannot + change bitrate or SFF/EFF mode on-the-fly. This will have to be + programmed by the user before attaching the line discipline. See the + data sheet for details. + + +- Versions prior to 1.3 + + These chips cannot be used at all with can327. They do not support + the "``AT D1``" command, which is necessary to avoid parsing conflicts + on incoming data, as well as distinction of RTR frame lengths. + + Specifically, this allows for easy distinction of SFF and EFF + frames, and to check whether frames are complete. While it is possible + to deduce the type and length from the length of the line the ELM327 + sends us, this method fails when the ELM327's UART output buffer + overruns. It may abort sending in the middle of the line, which will + then be mistaken for something else. + + + +Known limitations of the driver +-------------------------------- + +- No 8/7 timing. + + ELM327 can only set CAN bitrates that are of the form 500000/n, where + n is an integer divisor. + However there is an exception: With a separate flag, it may set the + speed to be 8/7 of the speed indicated by the divisor. + This mode is not currently implemented. + +- No evaluation of command responses. + + The ELM327 will reply with OK when a command is understood, and with ? + when it is not. The driver does not currently check this, and simply + assumes that the chip understands every command. + The driver is built such that functionality degrades gracefully + nevertheless. See the section on known limitations of the controller. + +- No use of hardware CAN ID filtering + + An ELM327's UART sending buffer will easily overflow on heavy CAN bus + load, resulting in the "``BUFFER FULL``" message. Using the hardware + filters available through "``AT CF xxx``" and "``AT CM xxx``" would be + helpful here, however SocketCAN does not currently provide a facility + to make use of such hardware features. + + + +Rationale behind the chosen configuration +------------------------------------------ + +``AT E1`` + Echo on + + We need this to be able to get a prompt reliably. + +``AT S1`` + Spaces on + + We need this to distinguish 11/29 bit CAN addresses received. + + Note: + We can usually do this using the line length (odd/even), + but this fails if the line is not transmitted fully to + the host (BUFFER FULL). + +``AT D1`` + DLC on + + We need this to tell the "length" of RTR frames. + + + +A note on CAN bus termination +------------------------------ + +Your adapter may have resistors soldered in which are meant to terminate +the bus. This is correct when it is plugged into a OBD-II socket, but +not helpful when trying to tap into the middle of an existing CAN bus. + +If communications don't work with the adapter connected, check for the +termination resistors on its PCB and try removing them. diff --git a/Documentation/networking/device_drivers/can/ctu/ctucanfd-driver.rst b/Documentation/networking/device_drivers/can/ctu/ctucanfd-driver.rst new file mode 100644 index 0000000000..1661d13174 --- /dev/null +++ b/Documentation/networking/device_drivers/can/ctu/ctucanfd-driver.rst @@ -0,0 +1,638 @@ +.. SPDX-License-Identifier: GPL-2.0-or-later + +CTU CAN FD Driver +================= + +Author: Martin Jerabek <martin.jerabek01@gmail.com> + + +About CTU CAN FD IP Core +------------------------ + +`CTU CAN FD <https://gitlab.fel.cvut.cz/canbus/ctucanfd_ip_core>`_ +is an open source soft core written in VHDL. +It originated in 2015 as Ondrej Ille's project +at the `Department of Measurement <https://meas.fel.cvut.cz/>`_ +of `FEE <http://www.fel.cvut.cz/en/>`_ at `CTU <https://www.cvut.cz/en>`_. + +The SocketCAN driver for Xilinx Zynq SoC based MicroZed board +`Vivado integration <https://gitlab.fel.cvut.cz/canbus/zynq/zynq-can-sja1000-top>`_ +and Intel Cyclone V 5CSEMA4U23C6 based DE0-Nano-SoC Terasic board +`QSys integration <https://gitlab.fel.cvut.cz/canbus/intel-soc-ctucanfd>`_ +has been developed as well as support for +`PCIe integration <https://gitlab.fel.cvut.cz/canbus/pcie-ctucanfd>`_ of the core. + +In the case of Zynq, the core is connected via the APB system bus, which does +not have enumeration support, and the device must be specified in Device Tree. +This kind of devices is called platform device in the kernel and is +handled by a platform device driver. + +The basic functional model of the CTU CAN FD peripheral has been +accepted into QEMU mainline. See QEMU `CAN emulation support <https://www.qemu.org/docs/master/system/devices/can.html>`_ +for CAN FD buses, host connection and CTU CAN FD core emulation. The development +version of emulation support can be cloned from ctu-canfd branch of QEMU local +development `repository <https://gitlab.fel.cvut.cz/canbus/qemu-canbus>`_. + + +About SocketCAN +--------------- + +SocketCAN is a standard common interface for CAN devices in the Linux +kernel. As the name suggests, the bus is accessed via sockets, similarly +to common network devices. The reasoning behind this is in depth +described in `Linux SocketCAN <https://www.kernel.org/doc/html/latest/networking/can.html>`_. +In short, it offers a +natural way to implement and work with higher layer protocols over CAN, +in the same way as, e.g., UDP/IP over Ethernet. + +Device probe +~~~~~~~~~~~~ + +Before going into detail about the structure of a CAN bus device driver, +let's reiterate how the kernel gets to know about the device at all. +Some buses, like PCI or PCIe, support device enumeration. That is, when +the system boots, it discovers all the devices on the bus and reads +their configuration. The kernel identifies the device via its vendor ID +and device ID, and if there is a driver registered for this identifier +combination, its probe method is invoked to populate the driver's +instance for the given hardware. A similar situation goes with USB, only +it allows for device hot-plug. + +The situation is different for peripherals which are directly embedded +in the SoC and connected to an internal system bus (AXI, APB, Avalon, +and others). These buses do not support enumeration, and thus the kernel +has to learn about the devices from elsewhere. This is exactly what the +Device Tree was made for. + +Device tree +~~~~~~~~~~~ + +An entry in device tree states that a device exists in the system, how +it is reachable (on which bus it resides) and its configuration – +registers address, interrupts and so on. An example of such a device +tree is given in . + +:: + + / { + /* ... */ + amba: amba { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + + CTU_CAN_FD_0: CTU_CAN_FD@43c30000 { + compatible = "ctu,ctucanfd"; + interrupt-parent = <&intc>; + interrupts = <0 30 4>; + clocks = <&clkc 15>; + reg = <0x43c30000 0x10000>; + }; + }; + }; + + +.. _sec:socketcan:drv: + +Driver structure +~~~~~~~~~~~~~~~~ + +The driver can be divided into two parts – platform-dependent device +discovery and set up, and platform-independent CAN network device +implementation. + +.. _sec:socketcan:platdev: + +Platform device driver +^^^^^^^^^^^^^^^^^^^^^^ + +In the case of Zynq, the core is connected via the AXI system bus, which +does not have enumeration support, and the device must be specified in +Device Tree. This kind of devices is called *platform device* in the +kernel and is handled by a *platform device driver*\ [1]_. + +A platform device driver provides the following things: + +- A *probe* function + +- A *remove* function + +- A table of *compatible* devices that the driver can handle + +The *probe* function is called exactly once when the device appears (or +the driver is loaded, whichever happens later). If there are more +devices handled by the same driver, the *probe* function is called for +each one of them. Its role is to allocate and initialize resources +required for handling the device, as well as set up low-level functions +for the platform-independent layer, e.g., *read_reg* and *write_reg*. +After that, the driver registers the device to a higher layer, in our +case as a *network device*. + +The *remove* function is called when the device disappears, or the +driver is about to be unloaded. It serves to free the resources +allocated in *probe* and to unregister the device from higher layers. + +Finally, the table of *compatible* devices states which devices the +driver can handle. The Device Tree entry ``compatible`` is matched +against the tables of all *platform drivers*. + +.. code:: c + + /* Match table for OF platform binding */ + static const struct of_device_id ctucan_of_match[] = { + { .compatible = "ctu,canfd-2", }, + { .compatible = "ctu,ctucanfd", }, + { /* end of list */ }, + }; + MODULE_DEVICE_TABLE(of, ctucan_of_match); + + static int ctucan_probe(struct platform_device *pdev); + static int ctucan_remove(struct platform_device *pdev); + + static struct platform_driver ctucanfd_driver = { + .probe = ctucan_probe, + .remove = ctucan_remove, + .driver = { + .name = DRIVER_NAME, + .of_match_table = ctucan_of_match, + }, + }; + module_platform_driver(ctucanfd_driver); + + +.. _sec:socketcan:netdev: + +Network device driver +^^^^^^^^^^^^^^^^^^^^^ + +Each network device must support at least these operations: + +- Bring the device up: ``ndo_open`` + +- Bring the device down: ``ndo_close`` + +- Submit TX frames to the device: ``ndo_start_xmit`` + +- Signal TX completion and errors to the network subsystem: ISR + +- Submit RX frames to the network subsystem: ISR and NAPI + +There are two possible event sources: the device and the network +subsystem. Device events are usually signaled via an interrupt, handled +in an Interrupt Service Routine (ISR). Handlers for the events +originating in the network subsystem are then specified in +``struct net_device_ops``. + +When the device is brought up, e.g., by calling ``ip link set can0 up``, +the driver’s function ``ndo_open`` is called. It should validate the +interface configuration and configure and enable the device. The +analogous opposite is ``ndo_close``, called when the device is being +brought down, be it explicitly or implicitly. + +When the system should transmit a frame, it does so by calling +``ndo_start_xmit``, which enqueues the frame into the device. If the +device HW queue (FIFO, mailboxes or whatever the implementation is) +becomes full, the ``ndo_start_xmit`` implementation informs the network +subsystem that it should stop the TX queue (via ``netif_stop_queue``). +It is then re-enabled later in ISR when the device has some space +available again and is able to enqueue another frame. + +All the device events are handled in ISR, namely: + +#. **TX completion**. When the device successfully finishes transmitting + a frame, the frame is echoed locally. On error, an informative error + frame [2]_ is sent to the network subsystem instead. In both cases, + the software TX queue is resumed so that more frames may be sent. + +#. **Error condition**. If something goes wrong (e.g., the device goes + bus-off or RX overrun happens), error counters are updated, and + informative error frames are enqueued to SW RX queue. + +#. **RX buffer not empty**. In this case, read the RX frames and enqueue + them to SW RX queue. Usually NAPI is used as a middle layer (see ). + +.. _sec:socketcan:napi: + +NAPI +~~~~ + +The frequency of incoming frames can be high and the overhead to invoke +the interrupt service routine for each frame can cause significant +system load. There are multiple mechanisms in the Linux kernel to deal +with this situation. They evolved over the years of Linux kernel +development and enhancements. For network devices, the current standard +is NAPI – *the New API*. It is similar to classical top-half/bottom-half +interrupt handling in that it only acknowledges the interrupt in the ISR +and signals that the rest of the processing should be done in softirq +context. On top of that, it offers the possibility to *poll* for new +frames for a while. This has a potential to avoid the costly round of +enabling interrupts, handling an incoming IRQ in ISR, re-enabling the +softirq and switching context back to softirq. + +See :ref:`Documentation/networking/napi.rst <napi>` for more information. + +Integrating the core to Xilinx Zynq +----------------------------------- + +The core interfaces a simple subset of the Avalon +(search for Intel **Avalon Interface Specifications**) +bus as it was originally used on +Alterra FPGA chips, yet Xilinx natively interfaces with AXI +(search for ARM **AMBA AXI and ACE Protocol Specification AXI3, +AXI4, and AXI4-Lite, ACE and ACE-Lite**). +The most obvious solution would be to use +an Avalon/AXI bridge or implement some simple conversion entity. +However, the core’s interface is half-duplex with no handshake +signaling, whereas AXI is full duplex with two-way signaling. Moreover, +even AXI-Lite slave interface is quite resource-intensive, and the +flexibility and speed of AXI are not required for a CAN core. + +Thus a much simpler bus was chosen – APB (Advanced Peripheral Bus) +(search for ARM **AMBA APB Protocol Specification**). +APB-AXI bridge is directly available in +Xilinx Vivado, and the interface adaptor entity is just a few simple +combinatorial assignments. + +Finally, to be able to include the core in a block diagram as a custom +IP, the core, together with the APB interface, has been packaged as a +Vivado component. + +CTU CAN FD Driver design +------------------------ + +The general structure of a CAN device driver has already been examined +in . The next paragraphs provide a more detailed description of the CTU +CAN FD core driver in particular. + +Low-level driver +~~~~~~~~~~~~~~~~ + +The core is not intended to be used solely with SocketCAN, and thus it +is desirable to have an OS-independent low-level driver. This low-level +driver can then be used in implementations of OS driver or directly +either on bare metal or in a user-space application. Another advantage +is that if the hardware slightly changes, only the low-level driver +needs to be modified. + +The code [3]_ is in part automatically generated and in part written +manually by the core author, with contributions of the thesis’ author. +The low-level driver supports operations such as: set bit timing, set +controller mode, enable/disable, read RX frame, write TX frame, and so +on. + +Configuring bit timing +~~~~~~~~~~~~~~~~~~~~~~ + +On CAN, each bit is divided into four segments: SYNC, PROP, PHASE1, and +PHASE2. Their duration is expressed in multiples of a Time Quantum +(details in `CAN Specification, Version 2.0 <http://esd.cs.ucr.edu/webres/can20.pdf>`_, chapter 8). +When configuring +bitrate, the durations of all the segments (and time quantum) must be +computed from the bitrate and Sample Point. This is performed +independently for both the Nominal bitrate and Data bitrate for CAN FD. + +SocketCAN is fairly flexible and offers either highly customized +configuration by setting all the segment durations manually, or a +convenient configuration by setting just the bitrate and sample point +(and even that is chosen automatically per Bosch recommendation if not +specified). However, each CAN controller may have different base clock +frequency and different width of segment duration registers. The +algorithm thus needs the minimum and maximum values for the durations +(and clock prescaler) and tries to optimize the numbers to fit both the +constraints and the requested parameters. + +.. code:: c + + struct can_bittiming_const { + char name[16]; /* Name of the CAN controller hardware */ + __u32 tseg1_min; /* Time segment 1 = prop_seg + phase_seg1 */ + __u32 tseg1_max; + __u32 tseg2_min; /* Time segment 2 = phase_seg2 */ + __u32 tseg2_max; + __u32 sjw_max; /* Synchronisation jump width */ + __u32 brp_min; /* Bit-rate prescaler */ + __u32 brp_max; + __u32 brp_inc; + }; + + +[lst:can_bittiming_const] + +A curious reader will notice that the durations of the segments PROP_SEG +and PHASE_SEG1 are not determined separately but rather combined and +then, by default, the resulting TSEG1 is evenly divided between PROP_SEG +and PHASE_SEG1. In practice, this has virtually no consequences as the +sample point is between PHASE_SEG1 and PHASE_SEG2. In CTU CAN FD, +however, the duration registers ``PROP`` and ``PH1`` have different +widths (6 and 7 bits, respectively), so the auto-computed values might +overflow the shorter register and must thus be redistributed among the +two [4]_. + +Handling RX +~~~~~~~~~~~ + +Frame reception is handled in NAPI queue, which is enabled from ISR when +the RXNE (RX FIFO Not Empty) bit is set. Frames are read one by one +until either no frame is left in the RX FIFO or the maximum work quota +has been reached for the NAPI poll run (see ). Each frame is then passed +to the network interface RX queue. + +An incoming frame may be either a CAN 2.0 frame or a CAN FD frame. The +way to distinguish between these two in the kernel is to allocate either +``struct can_frame`` or ``struct canfd_frame``, the two having different +sizes. In the controller, the information about the frame type is stored +in the first word of RX FIFO. + +This brings us a chicken-egg problem: we want to allocate the ``skb`` +for the frame, and only if it succeeds, fetch the frame from FIFO; +otherwise keep it there for later. But to be able to allocate the +correct ``skb``, we have to fetch the first work of FIFO. There are +several possible solutions: + +#. Read the word, then allocate. If it fails, discard the rest of the + frame. When the system is low on memory, the situation is bad anyway. + +#. Always allocate ``skb`` big enough for an FD frame beforehand. Then + tweak the ``skb`` internals to look like it has been allocated for + the smaller CAN 2.0 frame. + +#. Add option to peek into the FIFO instead of consuming the word. + +#. If the allocation fails, store the read word into driver’s data. On + the next try, use the stored word instead of reading it again. + +Option 1 is simple enough, but not very satisfying if we could do +better. Option 2 is not acceptable, as it would require modifying the +private state of an integral kernel structure. The slightly higher +memory consumption is just a virtual cherry on top of the “cake”. Option +3 requires non-trivial HW changes and is not ideal from the HW point of +view. + +Option 4 seems like a good compromise, with its disadvantage being that +a partial frame may stay in the FIFO for a prolonged time. Nonetheless, +there may be just one owner of the RX FIFO, and thus no one else should +see the partial frame (disregarding some exotic debugging scenarios). +Basides, the driver resets the core on its initialization, so the +partial frame cannot be “adopted” either. In the end, option 4 was +selected [5]_. + +.. _subsec:ctucanfd:rxtimestamp: + +Timestamping RX frames +^^^^^^^^^^^^^^^^^^^^^^ + +The CTU CAN FD core reports the exact timestamp when the frame has been +received. The timestamp is by default captured at the sample point of +the last bit of EOF but is configurable to be captured at the SOF bit. +The timestamp source is external to the core and may be up to 64 bits +wide. At the time of writing, passing the timestamp from kernel to +userspace is not yet implemented, but is planned in the future. + +Handling TX +~~~~~~~~~~~ + +The CTU CAN FD core has 4 independent TX buffers, each with its own +state and priority. When the core wants to transmit, a TX buffer in +Ready state with the highest priority is selected. + +The priorities are 3bit numbers in register TX_PRIORITY +(nibble-aligned). This should be flexible enough for most use cases. +SocketCAN, however, supports only one FIFO queue for outgoing +frames [6]_. The buffer priorities may be used to simulate the FIFO +behavior by assigning each buffer a distinct priority and *rotating* the +priorities after a frame transmission is completed. + +In addition to priority rotation, the SW must maintain head and tail +pointers into the FIFO formed by the TX buffers to be able to determine +which buffer should be used for next frame (``txb_head``) and which +should be the first completed one (``txb_tail``). The actual buffer +indices are (obviously) modulo 4 (number of TX buffers), but the +pointers must be at least one bit wider to be able to distinguish +between FIFO full and FIFO empty – in this situation, +:math:`txb\_head \equiv txb\_tail\ (\textrm{mod}\ 4)`. An example of how +the FIFO is maintained, together with priority rotation, is depicted in + +| + ++------+---+---+---+---+ +| TXB# | 0 | 1 | 2 | 3 | ++======+===+===+===+===+ +| Seq | A | B | C | | ++------+---+---+---+---+ +| Prio | 7 | 6 | 5 | 4 | ++------+---+---+---+---+ +| | | T | | H | ++------+---+---+---+---+ + +| + ++------+---+---+---+---+ +| TXB# | 0 | 1 | 2 | 3 | ++======+===+===+===+===+ +| Seq | | B | C | | ++------+---+---+---+---+ +| Prio | 4 | 7 | 6 | 5 | ++------+---+---+---+---+ +| | | T | | H | ++------+---+---+---+---+ + +| + ++------+---+---+---+---+----+ +| TXB# | 0 | 1 | 2 | 3 | 0’ | ++======+===+===+===+===+====+ +| Seq | E | B | C | D | | ++------+---+---+---+---+----+ +| Prio | 4 | 7 | 6 | 5 | | ++------+---+---+---+---+----+ +| | | T | | | H | ++------+---+---+---+---+----+ + +| + +.. kernel-figure:: fsm_txt_buffer_user.svg + + TX Buffer states with possible transitions + +.. _subsec:ctucanfd:txtimestamp: + +Timestamping TX frames +^^^^^^^^^^^^^^^^^^^^^^ + +When submitting a frame to a TX buffer, one may specify the timestamp at +which the frame should be transmitted. The frame transmission may start +later, but not sooner. Note that the timestamp does not participate in +buffer prioritization – that is decided solely by the mechanism +described above. + +Support for time-based packet transmission was recently merged to Linux +v4.19 `Time-based packet transmission <https://lwn.net/Articles/748879/>`_, +but it remains yet to be researched +whether this functionality will be practical for CAN. + +Also similarly to retrieving the timestamp of RX frames, the core +supports retrieving the timestamp of TX frames – that is the time when +the frame was successfully delivered. The particulars are very similar +to timestamping RX frames and are described in . + +Handling RX buffer overrun +~~~~~~~~~~~~~~~~~~~~~~~~~~ + +When a received frame does no more fit into the hardware RX FIFO in its +entirety, RX FIFO overrun flag (STATUS[DOR]) is set and Data Overrun +Interrupt (DOI) is triggered. When servicing the interrupt, care must be +taken first to clear the DOR flag (via COMMAND[CDO]) and after that +clear the DOI interrupt flag. Otherwise, the interrupt would be +immediately [7]_ rearmed. + +**Note**: During development, it was discussed whether the internal HW +pipelining cannot disrupt this clear sequence and whether an additional +dummy cycle is necessary between clearing the flag and the interrupt. On +the Avalon interface, it indeed proved to be the case, but APB being +safe because it uses 2-cycle transactions. Essentially, the DOR flag +would be cleared, but DOI register’s Preset input would still be high +the cycle when the DOI clear request would also be applied (by setting +the register’s Reset input high). As Set had higher priority than Reset, +the DOI flag would not be reset. This has been already fixed by swapping +the Set/Reset priority (see issue #187). + +Reporting Error Passive and Bus Off conditions +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +It may be desirable to report when the node reaches *Error Passive*, +*Error Warning*, and *Bus Off* conditions. The driver is notified about +error state change by an interrupt (EPI, EWLI), and then proceeds to +determine the core’s error state by reading its error counters. + +There is, however, a slight race condition here – there is a delay +between the time when the state transition occurs (and the interrupt is +triggered) and when the error counters are read. When EPI is received, +the node may be either *Error Passive* or *Bus Off*. If the node goes +*Bus Off*, it obviously remains in the state until it is reset. +Otherwise, the node is *or was* *Error Passive*. However, it may happen +that the read state is *Error Warning* or even *Error Active*. It may be +unclear whether and what exactly to report in that case, but I +personally entertain the idea that the past error condition should still +be reported. Similarly, when EWLI is received but the state is later +detected to be *Error Passive*, *Error Passive* should be reported. + + +CTU CAN FD Driver Sources Reference +----------------------------------- + +.. kernel-doc:: drivers/net/can/ctucanfd/ctucanfd.h + :internal: + +.. kernel-doc:: drivers/net/can/ctucanfd/ctucanfd_base.c + :internal: + +.. kernel-doc:: drivers/net/can/ctucanfd/ctucanfd_pci.c + :internal: + +.. kernel-doc:: drivers/net/can/ctucanfd/ctucanfd_platform.c + :internal: + +CTU CAN FD IP Core and Driver Development Acknowledgment +--------------------------------------------------------- + +* Odrej Ille <ondrej.ille@gmail.com> + + * started the project as student at Department of Measurement, FEE, CTU + * invested great amount of personal time and enthusiasm to the project over years + * worked on more funded tasks + +* `Department of Measurement <https://meas.fel.cvut.cz/>`_, + `Faculty of Electrical Engineering <http://www.fel.cvut.cz/en/>`_, + `Czech Technical University <https://www.cvut.cz/en>`_ + + * is the main investor into the project over many years + * uses project in their CAN/CAN FD diagnostics framework for `Skoda Auto <https://www.skoda-auto.cz/>`_ + +* `Digiteq Automotive <https://www.digiteqautomotive.com/en>`_ + + * funding of the project CAN FD Open Cores Support Linux Kernel Based Systems + * negotiated and paid CTU to allow public access to the project + * provided additional funding of the work + +* `Department of Control Engineering <https://control.fel.cvut.cz/en>`_, + `Faculty of Electrical Engineering <http://www.fel.cvut.cz/en/>`_, + `Czech Technical University <https://www.cvut.cz/en>`_ + + * solving the project CAN FD Open Cores Support Linux Kernel Based Systems + * providing GitLab management + * virtual servers and computational power for continuous integration + * providing hardware for HIL continuous integration tests + +* `PiKRON Ltd. <http://pikron.com/>`_ + + * minor funding to initiate preparation of the project open-sourcing + +* Petr Porazil <porazil@pikron.com> + + * design of PCIe transceiver addon board and assembly of boards + * design and assembly of MZ_APO baseboard for MicroZed/Zynq based system + +* Martin Jerabek <martin.jerabek01@gmail.com> + + * Linux driver development + * continuous integration platform architect and GHDL updates + * thesis `Open-source and Open-hardware CAN FD Protocol Support <https://dspace.cvut.cz/bitstream/handle/10467/80366/F3-DP-2019-Jerabek-Martin-Jerabek-thesis-2019-canfd.pdf>`_ + +* Jiri Novak <jnovak@fel.cvut.cz> + + * project initiation, management and use at Department of Measurement, FEE, CTU + +* Pavel Pisa <pisa@cmp.felk.cvut.cz> + + * initiate open-sourcing, project coordination, management at Department of Control Engineering, FEE, CTU + +* Jaroslav Beran<jara.beran@gmail.com> + + * system integration for Intel SoC, core and driver testing and updates + +* Carsten Emde (`OSADL <https://www.osadl.org/>`_) + + * provided OSADL expertise to discuss IP core licensing + * pointed to possible deadlock for LGPL and CAN bus possible patent case which lead to relicense IP core design to BSD like license + +* Reiner Zitzmann and Holger Zeltwanger (`CAN in Automation <https://www.can-cia.org/>`_) + + * provided suggestions and help to inform community about the project and invited us to events focused on CAN bus future development directions + +* Jan Charvat + + * implemented CTU CAN FD functional model for QEMU which has been integrated into QEMU mainline (`docs/system/devices/can.rst <https://www.qemu.org/docs/master/system/devices/can.html>`_) + * Bachelor thesis Model of CAN FD Communication Controller for QEMU Emulator + +Notes +----- + + +.. [1] + Other buses have their own specific driver interface to set up the + device. + +.. [2] + Not to be mistaken with CAN Error Frame. This is a ``can_frame`` with + ``CAN_ERR_FLAG`` set and some error info in its ``data`` field. + +.. [3] + Available in CTU CAN FD repository + `<https://gitlab.fel.cvut.cz/canbus/ctucanfd_ip_core>`_ + +.. [4] + As is done in the low-level driver functions + ``ctucan_hw_set_nom_bittiming`` and + ``ctucan_hw_set_data_bittiming``. + +.. [5] + At the time of writing this thesis, option 1 is still being used and + the modification is queued in gitlab issue #222 + +.. [6] + Strictly speaking, multiple CAN TX queues are supported since v4.19 + `can: enable multi-queue for SocketCAN devices <https://lore.kernel.org/patchwork/patch/913526/>`_ but no mainline driver is using + them yet. + +.. [7] + Or rather in the next clock cycle diff --git a/Documentation/networking/device_drivers/can/ctu/fsm_txt_buffer_user.svg b/Documentation/networking/device_drivers/can/ctu/fsm_txt_buffer_user.svg new file mode 100644 index 0000000000..381323423b --- /dev/null +++ b/Documentation/networking/device_drivers/can/ctu/fsm_txt_buffer_user.svg @@ -0,0 +1,151 @@ +<?xml version="1.0" encoding="UTF-8"?> +<svg width="113.611mm" height="86.6873mm" version="1.1" viewBox="0 0 113.611 86.6873" xmlns="http://www.w3.org/2000/svg" xmlns:cc="http://creativecommons.org/ns#" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:rdf="http://www.w3.org/1999/02/22-rdf-syntax-ns#"> + <defs> + <marker id="marker3667" overflow="visible" orient="auto"> + <path transform="scale(-.6)" d="m8.71859 4.03374-10.9259-4.01772 10.9259-4.01772c-1.7455 2.37206-1.73544 5.61745-6e-7 8.03544z" fill="#28a4ff" fill-rule="evenodd" stroke="#28a4ff" stroke-linejoin="round" stroke-width=".625"/> + </marker> + <marker id="marker3517" overflow="visible" orient="auto"> + <path transform="scale(-.6)" d="m8.71859 4.03374-10.9259-4.01772 10.9259-4.01772c-1.7455 2.37206-1.73544 5.61745-6e-7 8.03544z" fill-rule="evenodd" stroke="#000" stroke-linejoin="round" stroke-width=".625"/> + </marker> + <marker id="marker3373" overflow="visible" orient="auto"> + <path transform="scale(-.6)" d="m8.71859 4.03374-10.9259-4.01772 10.9259-4.01772c-1.7455 2.37206-1.73544 5.61745-6e-7 8.03544z" fill-rule="evenodd" stroke="#000" stroke-linejoin="round" stroke-width=".625"/> + </marker> + <marker id="marker3199" overflow="visible" orient="auto"> + <path transform="scale(-.6)" d="m8.71859 4.03374-10.9259-4.01772 10.9259-4.01772c-1.7455 2.37206-1.73544 5.61745-6e-7 8.03544z" fill="#28a4ff" fill-rule="evenodd" stroke="#28a4ff" stroke-linejoin="round" stroke-width=".625"/> + </marker> + <marker id="marker3037" overflow="visible" orient="auto"> + <path transform="scale(-.6)" d="m8.71859 4.03374-10.9259-4.01772 10.9259-4.01772c-1.7455 2.37206-1.73544 5.61745-6e-7 8.03544z" fill="#28a4ff" fill-rule="evenodd" stroke="#28a4ff" stroke-linejoin="round" stroke-width=".625"/> + </marker> + <marker id="marker2779" overflow="visible" orient="auto"> + <path transform="scale(-.6)" d="m8.71859 4.03374-10.9259-4.01772 10.9259-4.01772c-1.7455 2.37206-1.73544 5.61745-6e-7 8.03544z" fill="#28a4ff" fill-rule="evenodd" stroke="#28a4ff" stroke-linejoin="round" stroke-width=".625"/> + </marker> + <marker id="marker2477" overflow="visible" orient="auto"> + <path transform="scale(.6) rotate(180) translate(0)" d="m8.71859 4.03374-10.9259-4.01772 10.9259-4.01772c-1.7455 2.37206-1.73544 5.61745-6e-7 8.03544z" fill="#28a4ff" fill-rule="evenodd" stroke="#28a4ff" stroke-linejoin="round" stroke-width=".625"/> + </marker> + <marker id="marker2074" overflow="visible" orient="auto"> + <path transform="scale(.6) rotate(180) translate(0)" d="m8.71859 4.03374-10.9259-4.01772 10.9259-4.01772c-1.7455 2.37206-1.73544 5.61745-6e-7 8.03544z" fill-rule="evenodd" stroke="#000" stroke-linejoin="round" stroke-width=".625"/> + </marker> + <marker id="marker1964" overflow="visible" orient="auto"> + <path transform="scale(.6) rotate(180) translate(0)" d="m8.71859 4.03374-10.9259-4.01772 10.9259-4.01772c-1.7455 2.37206-1.73544 5.61745-6e-7 8.03544z" fill-rule="evenodd" stroke="#000" stroke-linejoin="round" stroke-width=".625"/> + </marker> + <marker id="marker1856" overflow="visible" orient="auto"> + <path transform="scale(.6) rotate(180) translate(0)" d="m8.71859 4.03374-10.9259-4.01772 10.9259-4.01772c-1.7455 2.37206-1.73544 5.61745-6e-7 8.03544z" fill-rule="evenodd" stroke="#000" stroke-linejoin="round" stroke-width=".625"/> + </marker> + <marker id="Arrow2Mend" overflow="visible" orient="auto"> + <path transform="scale(.6) rotate(180) translate(0)" d="m8.71859 4.03374-10.9259-4.01772 10.9259-4.01772c-1.7455 2.37206-1.73544 5.61745-6e-7 8.03544z" fill-rule="evenodd" stroke="#000" stroke-linejoin="round" stroke-width=".625"/> + </marker> + <filter id="filter1204" x="-4.19953e-6" y="-5.60084e-6" width="1.00001" height="1.00001" color-interpolation-filters="sRGB"> + <feGaussianBlur stdDeviation="0.00018829868"/> + </filter> + <marker id="marker2074-3" overflow="visible" orient="auto"> + <path transform="scale(-.6)" d="m8.71859 4.03374-10.9259-4.01772 10.9259-4.01772c-1.7455 2.37206-1.73544 5.61745-6e-7 8.03544z" fill="#28a4ff" fill-rule="evenodd" stroke="#28a4ff" stroke-linejoin="round" stroke-width=".625"/> + </marker> + <filter id="filter1204-6" x="-4.19953e-6" y="-5.60084e-6" width="1.00001" height="1.00001" color-interpolation-filters="sRGB"> + <feGaussianBlur stdDeviation="0.00018829868"/> + </filter> + <filter id="filter1204-6-9" x="-4.19953e-6" y="-5.60084e-6" width="1.00001" height="1.00001" color-interpolation-filters="sRGB"> + <feGaussianBlur stdDeviation="0.00018829868"/> + </filter> + <filter id="filter1204-6-2" x="-4.19953e-6" y="-5.60084e-6" width="1.00001" height="1.00001" color-interpolation-filters="sRGB"> + <feGaussianBlur stdDeviation="0.00018829868"/> + </filter> + <filter id="filter1204-6-2-9" x="-4.19953e-6" y="-5.60084e-6" width="1.00001" height="1.00001" color-interpolation-filters="sRGB"> + <feGaussianBlur stdDeviation="0.00018829868"/> + </filter> + <filter id="filter1204-6-2-9-4" x="-4.19953e-6" y="-5.60084e-6" width="1.00001" height="1.00001" color-interpolation-filters="sRGB"> + <feGaussianBlur stdDeviation="0.00018829868"/> + </filter> + <filter id="filter1204-6-2-9-1" x="-4.19953e-6" y="-5.60084e-6" width="1.00001" height="1.00001" color-interpolation-filters="sRGB"> + <feGaussianBlur stdDeviation="0.00018829868"/> + </filter> + <filter id="filter1204-6-2-9-1-3" x="-4.19953e-6" y="-5.60084e-6" width="1.00001" height="1.00001" color-interpolation-filters="sRGB"> + <feGaussianBlur stdDeviation="0.00018829868"/> + </filter> + <filter id="filter1204-6-2-9-1-3-1" x="-4.19953e-6" y="-5.60084e-6" width="1.00001" height="1.00001" color-interpolation-filters="sRGB"> + <feGaussianBlur stdDeviation="0.00018829868"/> + </filter> + </defs> + <metadata> + <rdf:RDF> + <cc:Work rdf:about=""> + <dc:format>image/svg+xml</dc:format> + <dc:type rdf:resource="http://purl.org/dc/dcmitype/StillImage"/> + <dc:title/> + </cc:Work> + </rdf:RDF> + </metadata> + <g transform="translate(-49.0277 -104.823)"> + <g> + <path d="m130.534 165.429h-71.1816v-17.5315" fill="none" marker-end="url(#marker2477)" stroke="#28a4ff" stroke-width=".6"/> + <path d="m145.034 122.959v-11.5914h-43.1215" fill="none" marker-end="url(#marker3037)" stroke="#28a4ff" stroke-width=".6"/> + <rect x="130.679" y="122.933" width="28.2965" height="45.2319" rx="0" ry="0" fill="#e5e5e5" stroke="#717171" stroke-linecap="square" stroke-width=".499999"/> + <path d="m102.044 116.236h23.3126l-0.13388 18.8185h19.9383v3.66603" fill="none" marker-end="url(#marker3199)" stroke="#28a4ff" stroke-width=".6"/> + <path d="m59.5006 138.391v-24.2517h20.6338" fill="none" marker-end="url(#marker2779)" stroke="#28a4ff" stroke-width=".6"/> + <rect x="78.1389" y="126.411" width="28.0037" height="35.0443" rx="0" ry="0" fill="#e5e5e5" stroke="#717171" stroke-linecap="square" stroke-width=".5"/> + </g> + <g fill="#ffcb35" stroke="#000" stroke-linecap="square"> + <ellipse cx="92.1408" cy="114.239" rx="10.8866" ry="4.39308" stroke-width=".5"/> + <ellipse cx="92.1408" cy="134.185" rx="10.8866" ry="4.39308" stroke-width=".499999"/> + <ellipse cx="92.1408" cy="152.199" rx="10.8866" ry="4.39308" stroke-width=".499999"/> + </g> + <g fill="#28a4ff" stroke="#000" stroke-linecap="square" stroke-width=".499999"> + <ellipse cx="144.827" cy="143.316" rx="10.8866" ry="4.39308"/> + <ellipse cx="144.827" cy="159.143" rx="10.8866" ry="4.39308"/> + <ellipse cx="59.4364" cy="142.823" rx="7.36455" ry="4.39308"/> + <ellipse cx="144.827" cy="129.196" rx="10.8866" ry="4.39308"/> + <ellipse cx="143.077" cy="180.53" rx="10.8866" ry="4.39308"/> + </g> + <ellipse cx="110.386" cy="180.53" rx="10.8866" ry="4.39308" fill="#ffcb35" stroke="#000" stroke-linecap="square" stroke-width=".499999"/> + <text x="110.90907" y="179.42688" font-size="3.175px" xml:space="preserve"><tspan x="110.90907" y="179.42688" dy="0.60000002" text-align="center" text-anchor="middle">Accessible</tspan><tspan x="110.90907" y="183.39563"><tspan font-size="3.175px" text-align="center" text-anchor="middle">for S</tspan>W</tspan></text> + <text x="143.5869" y="179.52795" xml:space="preserve"><tspan x="143.5869" y="179.52795" dy="1 0 0 0 0 0" font-family="sans-serif" font-size="2.82222px" text-align="center" text-anchor="middle" style="font-variant-caps:normal;font-variant-east-asian:normal;font-variant-ligatures:normal;font-variant-numeric:normal">Inaccessible</tspan><tspan x="143.5869" y="183.36786" font-size="3.175px"><tspan font-size="3.175px" text-align="center" text-anchor="middle">for S</tspan>W</tspan></text> + <g font-size="3.175px"> + <text x="91.95018" y="115.29005" xml:space="preserve"><tspan x="91.95018" y="115.29005" font-size="3.175px"><tspan font-size="3.175px" text-align="center" text-anchor="middle">Ready</tspan></tspan></text> + <text x="145.25127" y="130.49019" xml:space="preserve"><tspan x="145.25127" y="130.49019" font-size="3.175px"><tspan font-size="3.175px" text-align="center" text-anchor="middle">TX OK</tspan></tspan></text> + <text x="145.31845" y="144.43121" xml:space="preserve"><tspan x="145.31845" y="144.43121" font-size="3.175px"><tspan font-size="3.175px" text-align="center" text-anchor="middle">Aborted</tspan></tspan></text> + <text x="145.40399" y="160.36035" xml:space="preserve"><tspan x="145.40399" y="160.36035" font-size="3.175px"><tspan font-size="3.175px" text-align="center" text-anchor="middle">TX failed</tspan></tspan></text> + <text x="91.823967" y="133.53941" text-align="center" text-anchor="middle" style="line-height:0.9" xml:space="preserve"><tspan x="91.823967" y="133.53941" text-align="center"><tspan font-size="3.175px" text-align="center" text-anchor="middle">TX in</tspan></tspan><tspan x="91.823967" y="136.39691" text-align="center">progress</tspan></text> + <text x="91.648918" y="151.84813" text-align="center" text-anchor="middle" style="line-height:0.9" xml:space="preserve"><tspan x="91.648918" y="151.84813" text-align="center"><tspan font-size="3.175px" text-align="center" text-anchor="middle">Abort in</tspan></tspan><tspan x="91.648918" y="154.70563" text-align="center">progress</tspan></text> + <text x="59.456043" y="143.91658" xml:space="preserve"><tspan x="59.456043" y="143.91658" font-size="3.175px"><tspan font-size="3.175px" text-align="center" text-anchor="middle">Empty</tspan></tspan></text> + </g> + <g fill="none"> + <g stroke="#000"> + <rect x="52.3943" y="171.63" width="106.581" height="16.601" rx="0" ry="0" stroke-linecap="square" stroke-width=".499999"/> + <g stroke-width=".6"> + <path d="m106.383 159.046h26.4967" marker-end="url(#Arrow2Mend)"/> + <path d="m103.138 152.268h41.5564v-3.92426" marker-end="url(#marker1856)"/> + <path d="m106.38 129.354h17.7785"/> + <path d="m125.818 129.359h7.2418" marker-end="url(#marker1964)"/> + </g> + <path d="m124.169 129.354a0.959514 0.97091 0 0 1 0.47587-0.84557 0.959514 0.97091 0 0 1 0.96164-3e-3 0.959514 0.97091 0 0 1 0.48149 0.84231" stroke-linecap="square" stroke-width=".600001"/> + <path d="m55.7026 180.832h34.8131" marker-end="url(#marker2074)" stroke-width=".6"/> + </g> + <g> + <path d="m55.6464 185.744h34.8131" marker-end="url(#marker2074-3)" stroke="#28a4ff" stroke-width=".600001"/> + <g stroke-width=".6"> + <path d="m94.0487 129.889v-10.6493" marker-end="url(#marker3373)" stroke="#000"/> + <path d="m89.7534 118.621v10.662" marker-end="url(#marker3517)" stroke="#000"/> + <path d="m92.119 138.812v7.9718" marker-end="url(#marker3667)" stroke="#28a4ff"/> + </g> + </g> + </g> + <text transform="matrix(.264583 0 0 .264583 91.8919 139.964)" x="26.959213" y="9.11724" fill="#2aa1ff" filter="url(#filter1204-6-2-9-1-3-1)" font-size="12px" stroke-width="3.77953" text-align="center" text-anchor="middle" style="line-height:1.1" xml:space="preserve"><tspan x="26.959213" y="9.11724" text-align="center">Set</tspan><tspan x="26.959213" y="22.31724" text-align="center">abort</tspan></text> + <text transform="translate(49.0277 104.823)" x="57.620724" y="16.855087" filter="url(#filter1204)" font-size="3.175px" text-align="center" text-anchor="middle" style="line-height:1.1" xml:space="preserve"><tspan x="57.620724" y="16.855087" text-align="center">Transmission</tspan><tspan x="57.620724" y="20.347588" text-align="center">unsuccessful</tspan></text> + <g font-size="12px" stroke-width="3.77953" text-anchor="middle"> + <text transform="matrix(.264583 0 0 .264583 68.5988 118.913)" x="38.824219" y="9.1171875" filter="url(#filter1204)" text-align="center" style="line-height:1.1" xml:space="preserve"><tspan x="38.824219" y="9.1171875" text-align="center">Transmission</tspan><tspan x="38.824219" y="22.317188" text-align="center">starts</tspan></text> + <text transform="matrix(.264583 0 0 .264583 106.802 130.509)" x="38.824219" y="9.1171875" filter="url(#filter1204)" text-align="center" style="line-height:1.1" xml:space="preserve"><tspan x="38.824219" y="9.1171875" text-align="center">Transmission</tspan><tspan x="38.824219" y="22.317188" text-align="center">successful</tspan></text> + <text transform="matrix(.264583 0 0 .264583 107.77 145.476)" x="38.824219" y="9.1171875" filter="url(#filter1204)" text-align="center" style="line-height:1.1" xml:space="preserve"><tspan x="38.824219" y="9.1171875" text-align="center">Transmission</tspan><tspan x="38.824219" y="22.317188" text-align="center">sborted</tspan></text> + </g> + <g stroke-width="3.77953" text-anchor="middle"> + <text transform="matrix(.264583 0 0 .264583 107.574 155.948)" x="38.824219" y="9.1171875" filter="url(#filter1204)" font-size="10.6667px" text-align="center" style="line-height:1.1" xml:space="preserve"><tspan x="38.824219" y="9.1171875" text-align="center">Retransmit</tspan><tspan x="38.824219" y="20.850557" text-align="center">limit reached or</tspan><tspan x="38.824219" y="32.583927" text-align="center">node went bus off</tspan><tspan x="38.824219" y="44.317299" text-align="center"/></text> + <text transform="matrix(.264583 0 0 .264583 60.7127 177.384)" x="38.824539" y="9.1173134" filter="url(#filter1204-6)" font-size="12px" text-align="center" style="line-height:1.1" xml:space="preserve"><tspan x="38.824539" y="9.1173134" font-size="12px" stroke-width="3.77953" text-align="center" text-anchor="middle">Transmission result</tspan></text> + <text transform="matrix(.264583 0 0 .264583 45.6885 173.226)" x="57.727047" y="9.11724" filter="url(#filter1204-6-9)" font-size="12px" text-align="center" style="line-height:1.1" xml:space="preserve"><tspan x="57.727047" y="9.11724" font-size="12px" stroke-width="3.77953" text-align="center" text-anchor="middle">Legend:</tspan></text> + </g> + <g fill="#2aa1ff" font-size="12px" stroke-width="3.77953" text-anchor="middle"> + <text transform="matrix(.264583 0 0 .264583 57.0045 182.079)" x="57.727047" y="9.11724" filter="url(#filter1204-6-2)" text-align="center" style="line-height:1.1" xml:space="preserve"><tspan x="57.727047" y="9.11724" fill="#2aa1ff" font-size="12px" stroke-width="3.77953" text-align="center" text-anchor="middle">SW command</tspan></text> + <text transform="matrix(.264583 0 0 .264583 57.7865 110.104)" x="40.822609" y="9.11724" filter="url(#filter1204-6-2-9)" text-align="center" style="line-height:1.1" xml:space="preserve"><tspan x="40.822609" y="9.11724" fill="#2aa1ff" font-size="12px" stroke-width="3.77953" text-align="center" text-anchor="middle">Set ready</tspan></text> + <text transform="matrix(.264583 0 0 .264583 116.893 107.491)" x="28.049065" y="9.1172523" filter="url(#filter1204-6-2-9-4)" text-align="center" style="line-height:1.1" xml:space="preserve"><tspan x="28.049065" y="9.1172523" fill="#2aa1ff" font-size="12px" stroke-width="3.77953" text-align="center" text-anchor="middle">Set ready</tspan></text> + <text transform="matrix(.264583 0 0 .264583 87.5687 166.324)" x="28.049065" y="9.1172523" filter="url(#filter1204-6-2-9-1)" text-align="center" style="line-height:1.1" xml:space="preserve"><tspan x="28.049065" y="9.1172523" fill="#2aa1ff" font-size="12px" stroke-width="3.77953" text-align="center" text-anchor="middle">Set empty</tspan></text> + <text transform="matrix(.264583 0 0 .264583 106.53 113.074)" x="30.228771" y="8.9063139" filter="url(#filter1204-6-2-9-1-3)" text-align="center" style="line-height:1.1" xml:space="preserve"><tspan x="30.228771" y="8.9063139" fill="#2aa1ff" font-size="12px" stroke-width="3.77953" text-align="center" text-anchor="middle">Set abort</tspan></text> + </g> + </g> +</svg> diff --git a/Documentation/networking/device_drivers/can/freescale/flexcan.rst b/Documentation/networking/device_drivers/can/freescale/flexcan.rst new file mode 100644 index 0000000000..106cd28901 --- /dev/null +++ b/Documentation/networking/device_drivers/can/freescale/flexcan.rst @@ -0,0 +1,54 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +============================= +Flexcan CAN Controller driver +============================= + +Authors: Marc Kleine-Budde <mkl@pengutronix.de>, +Dario Binacchi <dario.binacchi@amarulasolutions.com> + +On/off RTR frames reception +=========================== + +For most flexcan IP cores the driver supports 2 RX modes: + +- FIFO +- mailbox + +The older flexcan cores (integrated into the i.MX25, i.MX28, i.MX35 +and i.MX53 SOCs) only receive RTR frames if the controller is +configured for RX-FIFO mode. + +The RX FIFO mode uses a hardware FIFO with a depth of 6 CAN frames, +while the mailbox mode uses a software FIFO with a depth of up to 62 +CAN frames. With the help of the bigger buffer, the mailbox mode +performs better under high system load situations. + +As reception of RTR frames is part of the CAN standard, all flexcan +cores come up in a mode where RTR reception is possible. + +With the "rx-rtr" private flag the ability to receive RTR frames can +be waived at the expense of losing the ability to receive RTR +messages. This trade off is beneficial in certain use cases. + +"rx-rtr" on + Receive RTR frames. (default) + + The CAN controller can and will receive RTR frames. + + On some IP cores the controller cannot receive RTR frames in the + more performant "RX mailbox" mode and will use "RX FIFO" mode + instead. + +"rx-rtr" off + + Waive ability to receive RTR frames. (not supported on all IP cores) + + This mode activates the "RX mailbox mode" for better performance, on + some IP cores RTR frames cannot be received anymore. + +The setting can only be changed if the interface is down:: + + ip link set dev can0 down + ethtool --set-priv-flags can0 rx-rtr {off|on} + ip link set dev can0 up diff --git a/Documentation/networking/device_drivers/can/index.rst b/Documentation/networking/device_drivers/can/index.rst new file mode 100644 index 0000000000..6a8a4f74fa --- /dev/null +++ b/Documentation/networking/device_drivers/can/index.rst @@ -0,0 +1,22 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) + +Controller Area Network (CAN) Device Drivers +============================================ + +Device drivers for CAN devices. + +Contents: + +.. toctree:: + :maxdepth: 2 + + can327 + ctu/ctucanfd-driver + freescale/flexcan + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/cellular/index.rst b/Documentation/networking/device_drivers/cellular/index.rst new file mode 100644 index 0000000000..fc1812d3fc --- /dev/null +++ b/Documentation/networking/device_drivers/cellular/index.rst @@ -0,0 +1,18 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) + +Cellular Modem Device Drivers +============================= + +Contents: + +.. toctree:: + :maxdepth: 2 + + qualcomm/rmnet + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/cellular/qualcomm/rmnet.rst b/Documentation/networking/device_drivers/cellular/qualcomm/rmnet.rst new file mode 100644 index 0000000000..289c146a82 --- /dev/null +++ b/Documentation/networking/device_drivers/cellular/qualcomm/rmnet.rst @@ -0,0 +1,196 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============ +Rmnet Driver +============ + +1. Introduction +=============== + +rmnet driver is used for supporting the Multiplexing and aggregation +Protocol (MAP). This protocol is used by all recent chipsets using Qualcomm +Technologies, Inc. modems. + +This driver can be used to register onto any physical network device in +IP mode. Physical transports include USB, HSIC, PCIe and IP accelerator. + +Multiplexing allows for creation of logical netdevices (rmnet devices) to +handle multiple private data networks (PDN) like a default internet, tethering, +multimedia messaging service (MMS) or IP media subsystem (IMS). Hardware sends +packets with MAP headers to rmnet. Based on the multiplexer id, rmnet +routes to the appropriate PDN after removing the MAP header. + +Aggregation is required to achieve high data rates. This involves hardware +sending aggregated bunch of MAP frames. rmnet driver will de-aggregate +these MAP frames and send them to appropriate PDN's. + +2. Packet format +================ + +a. MAP packet v1 (data / control) + +MAP header fields are in big endian format. + +Packet format:: + + Bit 0 1 2-7 8-15 16-31 + Function Command / Data Reserved Pad Multiplexer ID Payload length + + Bit 32-x + Function Raw bytes + +Command (1)/ Data (0) bit value is to indicate if the packet is a MAP command +or data packet. Command packet is used for transport level flow control. Data +packets are standard IP packets. + +Reserved bits must be zero when sent and ignored when received. + +Padding is the number of bytes to be appended to the payload to +ensure 4 byte alignment. + +Multiplexer ID is to indicate the PDN on which data has to be sent. + +Payload length includes the padding length but does not include MAP header +length. + +b. Map packet v4 (data / control) + +MAP header fields are in big endian format. + +Packet format:: + + Bit 0 1 2-7 8-15 16-31 + Function Command / Data Reserved Pad Multiplexer ID Payload length + + Bit 32-(x-33) (x-32)-x + Function Raw bytes Checksum offload header + +Command (1)/ Data (0) bit value is to indicate if the packet is a MAP command +or data packet. Command packet is used for transport level flow control. Data +packets are standard IP packets. + +Reserved bits must be zero when sent and ignored when received. + +Padding is the number of bytes to be appended to the payload to +ensure 4 byte alignment. + +Multiplexer ID is to indicate the PDN on which data has to be sent. + +Payload length includes the padding length but does not include MAP header +length. + +Checksum offload header, has the information about the checksum processing done +by the hardware.Checksum offload header fields are in big endian format. + +Packet format:: + + Bit 0-14 15 16-31 + Function Reserved Valid Checksum start offset + + Bit 31-47 48-64 + Function Checksum length Checksum value + +Reserved bits must be zero when sent and ignored when received. + +Valid bit indicates whether the partial checksum is calculated and is valid. +Set to 1, if its is valid. Set to 0 otherwise. + +Padding is the number of bytes to be appended to the payload to +ensure 4 byte alignment. + +Checksum start offset, Indicates the offset in bytes from the beginning of the +IP header, from which modem computed checksum. + +Checksum length is the Length in bytes starting from CKSUM_START_OFFSET, +over which checksum is computed. + +Checksum value, indicates the checksum computed. + +c. MAP packet v5 (data / control) + +MAP header fields are in big endian format. + +Packet format:: + + Bit 0 1 2-7 8-15 16-31 + Function Command / Data Next header Pad Multiplexer ID Payload length + + Bit 32-x + Function Raw bytes + +Command (1)/ Data (0) bit value is to indicate if the packet is a MAP command +or data packet. Command packet is used for transport level flow control. Data +packets are standard IP packets. + +Next header is used to indicate the presence of another header, currently is +limited to checksum header. + +Padding is the number of bytes to be appended to the payload to +ensure 4 byte alignment. + +Multiplexer ID is to indicate the PDN on which data has to be sent. + +Payload length includes the padding length but does not include MAP header +length. + +d. Checksum offload header v5 + +Checksum offload header fields are in big endian format. + + Bit 0 - 6 7 8-15 16-31 + Function Header Type Next Header Checksum Valid Reserved + +Header Type is to indicate the type of header, this usually is set to CHECKSUM + +Header types += ========================================== +0 Reserved +1 Reserved +2 checksum header + +Checksum Valid is to indicate whether the header checksum is valid. Value of 1 +implies that checksum is calculated on this packet and is valid, value of 0 +indicates that the calculated packet checksum is invalid. + +Reserved bits must be zero when sent and ignored when received. + +e. MAP packet v1/v5 (command specific):: + + Bit 0 1 2-7 8 - 15 16 - 31 + Function Command Reserved Pad Multiplexer ID Payload length + Bit 32 - 39 40 - 45 46 - 47 48 - 63 + Function Command name Reserved Command Type Reserved + Bit 64 - 95 + Function Transaction ID + Bit 96 - 127 + Function Command data + +Command 1 indicates disabling flow while 2 is enabling flow + +Command types + += ========================================== +0 for MAP command request +1 is to acknowledge the receipt of a command +2 is for unsupported commands +3 is for error during processing of commands += ========================================== + +f. Aggregation + +Aggregation is multiple MAP packets (can be data or command) delivered to +rmnet in a single linear skb. rmnet will process the individual +packets and either ACK the MAP command or deliver the IP packet to the +network stack as needed + +MAP header|IP Packet|Optional padding|MAP header|IP Packet|Optional padding.... + +MAP header|IP Packet|Optional padding|MAP header|Command Packet|Optional pad... + +3. Userspace configuration +========================== + +rmnet userspace configuration is done through netlink using iproute2 +https://git.kernel.org/pub/scm/network/iproute2/iproute2.git/ + +The driver uses rtnl_link_ops for communication. diff --git a/Documentation/networking/device_drivers/ethernet/3com/3c509.rst b/Documentation/networking/device_drivers/ethernet/3com/3c509.rst new file mode 100644 index 0000000000..47f706bacd --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/3com/3c509.rst @@ -0,0 +1,249 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============================================================================= +Linux and the 3Com EtherLink III Series Ethercards (driver v1.18c and higher) +============================================================================= + +This file contains the instructions and caveats for v1.18c and higher versions +of the 3c509 driver. You should not use the driver without reading this file. + +release 1.0 + +28 February 2002 + +Current maintainer (corrections to): + David Ruggiero <jdr@farfalle.com> + +Introduction +============ + +The following are notes and information on using the 3Com EtherLink III series +ethercards in Linux. These cards are commonly known by the most widely-used +card's 3Com model number, 3c509. They are all 10mb/s ISA-bus cards and shouldn't +be (but sometimes are) confused with the similarly-numbered PCI-bus "3c905" +(aka "Vortex" or "Boomerang") series. Kernel support for the 3c509 family is +provided by the module 3c509.c, which has code to support all of the following +models: + + - 3c509 (original ISA card) + - 3c509B (later revision of the ISA card; supports full-duplex) + - 3c589 (PCMCIA) + - 3c589B (later revision of the 3c589; supports full-duplex) + - 3c579 (EISA) + +Large portions of this documentation were heavily borrowed from the guide +written the original author of the 3c509 driver, Donald Becker. The master +copy of that document, which contains notes on older versions of the driver, +currently resides on Scyld web server: http://www.scyld.com/. + + +Special Driver Features +======================= + +Overriding card settings + +The driver allows boot- or load-time overriding of the card's detected IOADDR, +IRQ, and transceiver settings, although this capability shouldn't generally be +needed except to enable full-duplex mode (see below). An example of the syntax +for LILO parameters for doing this:: + + ether=10,0x310,3,0x3c509,eth0 + +This configures the first found 3c509 card for IRQ 10, base I/O 0x310, and +transceiver type 3 (10base2). The flag "0x3c509" must be set to avoid conflicts +with other card types when overriding the I/O address. When the driver is +loaded as a module, only the IRQ may be overridden. For example, +setting two cards to IRQ10 and IRQ11 is done by using the irq module +option:: + + options 3c509 irq=10,11 + + +Full-duplex mode +================ + +The v1.18c driver added support for the 3c509B's full-duplex capabilities. +In order to enable and successfully use full-duplex mode, three conditions +must be met: + +(a) You must have a Etherlink III card model whose hardware supports full- +duplex operations. Currently, the only members of the 3c509 family that are +positively known to support full-duplex are the 3c509B (ISA bus) and 3c589B +(PCMCIA) cards. Cards without the "B" model designation do *not* support +full-duplex mode; these include the original 3c509 (no "B"), the original +3c589, the 3c529 (MCA bus), and the 3c579 (EISA bus). + +(b) You must be using your card's 10baseT transceiver (i.e., the RJ-45 +connector), not its AUI (thick-net) or 10base2 (thin-net/coax) interfaces. +AUI and 10base2 network cabling is physically incapable of full-duplex +operation. + +(c) Most importantly, your 3c509B must be connected to a link partner that is +itself full-duplex capable. This is almost certainly one of two things: a full- +duplex-capable Ethernet switch (*not* a hub), or a full-duplex-capable NIC on +another system that's connected directly to the 3c509B via a crossover cable. + +Full-duplex mode can be enabled using 'ethtool'. + +.. warning:: + + Extremely important caution concerning full-duplex mode + + Understand that the 3c509B's hardware's full-duplex support is much more + limited than that provide by more modern network interface cards. Although + at the physical layer of the network it fully supports full-duplex operation, + the card was designed before the current Ethernet auto-negotiation (N-way) + spec was written. This means that the 3c509B family ***cannot and will not + auto-negotiate a full-duplex connection with its link partner under any + circumstances, no matter how it is initialized***. If the full-duplex mode + of the 3c509B is enabled, its link partner will very likely need to be + independently _forced_ into full-duplex mode as well; otherwise various nasty + failures will occur - at the very least, you'll see massive numbers of packet + collisions. This is one of very rare circumstances where disabling auto- + negotiation and forcing the duplex mode of a network interface card or switch + would ever be necessary or desirable. + + +Available Transceiver Types +=========================== + +For versions of the driver v1.18c and above, the available transceiver types are: + +== ========================================================================= +0 transceiver type from EEPROM config (normally 10baseT); force half-duplex +1 AUI (thick-net / DB15 connector) +2 (undefined) +3 10base2 (thin-net == coax / BNC connector) +4 10baseT (RJ-45 connector); force half-duplex mode +8 transceiver type and duplex mode taken from card's EEPROM config settings +12 10baseT (RJ-45 connector); force full-duplex mode +== ========================================================================= + +Prior to driver version 1.18c, only transceiver codes 0-4 were supported. Note +that the new transceiver codes 8 and 12 are the *only* ones that will enable +full-duplex mode, no matter what the card's detected EEPROM settings might be. +This insured that merely upgrading the driver from an earlier version would +never automatically enable full-duplex mode in an existing installation; +it must always be explicitly enabled via one of these code in order to be +activated. + +The transceiver type can be changed using 'ethtool'. + + +Interpretation of error messages and common problems +---------------------------------------------------- + +Error Messages +^^^^^^^^^^^^^^ + +eth0: Infinite loop in interrupt, status 2011. +These are "mostly harmless" message indicating that the driver had too much +work during that interrupt cycle. With a status of 0x2011 you are receiving +packets faster than they can be removed from the card. This should be rare +or impossible in normal operation. Possible causes of this error report are: + + - a "green" mode enabled that slows the processor down when there is no + keyboard activity. + + - some other device or device driver hogging the bus or disabling interrupts. + Check /proc/interrupts for excessive interrupt counts. The timer tick + interrupt should always be incrementing faster than the others. + +No received packets +^^^^^^^^^^^^^^^^^^^ + +If a 3c509, 3c562 or 3c589 can successfully transmit packets, but never +receives packets (as reported by /proc/net/dev or 'ifconfig') you likely +have an interrupt line problem. Check /proc/interrupts to verify that the +card is actually generating interrupts. If the interrupt count is not +increasing you likely have a physical conflict with two devices trying to +use the same ISA IRQ line. The common conflict is with a sound card on IRQ10 +or IRQ5, and the easiest solution is to move the 3c509 to a different +interrupt line. If the device is receiving packets but 'ping' doesn't work, +you have a routing problem. + +Tx Carrier Errors Reported in /proc/net/dev +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + + +If an EtherLink III appears to transmit packets, but the "Tx carrier errors" +field in /proc/net/dev increments as quickly as the Tx packet count, you +likely have an unterminated network or the incorrect media transceiver selected. + +3c509B card is not detected on machines with an ISA PnP BIOS. +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +While the updated driver works with most PnP BIOS programs, it does not work +with all. This can be fixed by disabling PnP support using the 3Com-supplied +setup program. + +3c509 card is not detected on overclocked machines +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Increase the delay time in id_read_eeprom() from the current value, 500, +to an absurdly high value, such as 5000. + + +Decoding Status and Error Messages +---------------------------------- + + +The bits in the main status register are: + +===== ====================================== +value description +===== ====================================== +0x01 Interrupt latch +0x02 Tx overrun, or Rx underrun +0x04 Tx complete +0x08 Tx FIFO room available +0x10 A complete Rx packet has arrived +0x20 A Rx packet has started to arrive +0x40 The driver has requested an interrupt +0x80 Statistics counter nearly full +===== ====================================== + +The bits in the transmit (Tx) status word are: + +===== ============================================ +value description +===== ============================================ +0x02 Out-of-window collision. +0x04 Status stack overflow (normally impossible). +0x08 16 collisions. +0x10 Tx underrun (not enough PCI bus bandwidth). +0x20 Tx jabber. +0x40 Tx interrupt requested. +0x80 Status is valid (this should always be set). +===== ============================================ + + +When a transmit error occurs the driver produces a status message such as:: + + eth0: Transmit error, Tx status register 82 + +The two values typically seen here are: + +0x82 +^^^^ + +Out of window collision. This typically occurs when some other Ethernet +host is incorrectly set to full duplex on a half duplex network. + +0x88 +^^^^ + +16 collisions. This typically occurs when the network is exceptionally busy +or when another host doesn't correctly back off after a collision. If this +error is mixed with 0x82 errors it is the result of a host incorrectly set +to full duplex (see above). + +Both of these errors are the result of network problems that should be +corrected. They do not represent driver malfunction. + + +Revision history (this file) +============================ + +28Feb02 v1.0 DR New; major portions based on Becker original 3c509 docs + diff --git a/Documentation/networking/device_drivers/ethernet/3com/vortex.rst b/Documentation/networking/device_drivers/ethernet/3com/vortex.rst new file mode 100644 index 0000000000..a060f84c4f --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/3com/vortex.rst @@ -0,0 +1,459 @@ +.. SPDX-License-Identifier: GPL-2.0 + +========================= +3Com Vortex device driver +========================= + +Andrew Morton + +30 April 2000 + + +This document describes the usage and errata of the 3Com "Vortex" device +driver for Linux, 3c59x.c. + +The driver was written by Donald Becker <becker@scyld.com> + +Don is no longer the prime maintainer of this version of the driver. +Please report problems to one or more of: + +- Andrew Morton +- Netdev mailing list <netdev@vger.kernel.org> +- Linux kernel mailing list <linux-kernel@vger.kernel.org> + +Please note the 'Reporting and Diagnosing Problems' section at the end +of this file. + + +Since kernel 2.3.99-pre6, this driver incorporates the support for the +3c575-series Cardbus cards which used to be handled by 3c575_cb.c. + +This driver supports the following hardware: + + - 3c590 Vortex 10Mbps + - 3c592 EISA 10Mbps Demon/Vortex + - 3c597 EISA Fast Demon/Vortex + - 3c595 Vortex 100baseTx + - 3c595 Vortex 100baseT4 + - 3c595 Vortex 100base-MII + - 3c900 Boomerang 10baseT + - 3c900 Boomerang 10Mbps Combo + - 3c900 Cyclone 10Mbps TPO + - 3c900 Cyclone 10Mbps Combo + - 3c900 Cyclone 10Mbps TPC + - 3c900B-FL Cyclone 10base-FL + - 3c905 Boomerang 100baseTx + - 3c905 Boomerang 100baseT4 + - 3c905B Cyclone 100baseTx + - 3c905B Cyclone 10/100/BNC + - 3c905B-FX Cyclone 100baseFx + - 3c905C Tornado + - 3c920B-EMB-WNM (ATI Radeon 9100 IGP) + - 3c980 Cyclone + - 3c980C Python-T + - 3cSOHO100-TX Hurricane + - 3c555 Laptop Hurricane + - 3c556 Laptop Tornado + - 3c556B Laptop Hurricane + - 3c575 [Megahertz] 10/100 LAN CardBus + - 3c575 Boomerang CardBus + - 3CCFE575BT Cyclone CardBus + - 3CCFE575CT Tornado CardBus + - 3CCFE656 Cyclone CardBus + - 3CCFEM656B Cyclone+Winmodem CardBus + - 3CXFEM656C Tornado+Winmodem CardBus + - 3c450 HomePNA Tornado + - 3c920 Tornado + - 3c982 Hydra Dual Port A + - 3c982 Hydra Dual Port B + - 3c905B-T4 + - 3c920B-EMB-WNM Tornado + +Module parameters +================= + +There are several parameters which may be provided to the driver when +its module is loaded. These are usually placed in ``/etc/modprobe.d/*.conf`` +configuration files. Example:: + + options 3c59x debug=3 rx_copybreak=300 + +If you are using the PCMCIA tools (cardmgr) then the options may be +placed in /etc/pcmcia/config.opts:: + + module "3c59x" opts "debug=3 rx_copybreak=300" + + +The supported parameters are: + +debug=N + + Where N is a number from 0 to 7. Anything above 3 produces a lot + of output in your system logs. debug=1 is default. + +options=N1,N2,N3,... + + Each number in the list provides an option to the corresponding + network card. So if you have two 3c905's and you wish to provide + them with option 0x204 you would use:: + + options=0x204,0x204 + + The individual options are composed of a number of bitfields which + have the following meanings: + + Possible media type settings + + == ================================= + 0 10baseT + 1 10Mbs AUI + 2 undefined + 3 10base2 (BNC) + 4 100base-TX + 5 100base-FX + 6 MII (Media Independent Interface) + 7 Use default setting from EEPROM + 8 Autonegotiate + 9 External MII + 10 Use default setting from EEPROM + == ================================= + + When generating a value for the 'options' setting, the above media + selection values may be OR'ed (or added to) the following: + + ====== ============================================= + 0x8000 Set driver debugging level to 7 + 0x4000 Set driver debugging level to 2 + 0x0400 Enable Wake-on-LAN + 0x0200 Force full duplex mode. + 0x0010 Bus-master enable bit (Old Vortex cards only) + ====== ============================================= + + For example:: + + insmod 3c59x options=0x204 + + will force full-duplex 100base-TX, rather than allowing the usual + autonegotiation. + +global_options=N + + Sets the ``options`` parameter for all 3c59x NICs in the machine. + Entries in the ``options`` array above will override any setting of + this. + +full_duplex=N1,N2,N3... + + Similar to bit 9 of 'options'. Forces the corresponding card into + full-duplex mode. Please use this in preference to the ``options`` + parameter. + + In fact, please don't use this at all! You're better off getting + autonegotiation working properly. + +global_full_duplex=N1 + + Sets full duplex mode for all 3c59x NICs in the machine. Entries + in the ``full_duplex`` array above will override any setting of this. + +flow_ctrl=N1,N2,N3... + + Use 802.3x MAC-layer flow control. The 3com cards only support the + PAUSE command, which means that they will stop sending packets for a + short period if they receive a PAUSE frame from the link partner. + + The driver only allows flow control on a link which is operating in + full duplex mode. + + This feature does not appear to work on the 3c905 - only 3c905B and + 3c905C have been tested. + + The 3com cards appear to only respond to PAUSE frames which are + sent to the reserved destination address of 01:80:c2:00:00:01. They + do not honour PAUSE frames which are sent to the station MAC address. + +rx_copybreak=M + + The driver preallocates 32 full-sized (1536 byte) network buffers + for receiving. When a packet arrives, the driver has to decide + whether to leave the packet in its full-sized buffer, or to allocate + a smaller buffer and copy the packet across into it. + + This is a speed/space tradeoff. + + The value of rx_copybreak is used to decide when to make the copy. + If the packet size is less than rx_copybreak, the packet is copied. + The default value for rx_copybreak is 200 bytes. + +max_interrupt_work=N + + The driver's interrupt service routine can handle many receive and + transmit packets in a single invocation. It does this in a loop. + The value of max_interrupt_work governs how many times the interrupt + service routine will loop. The default value is 32 loops. If this + is exceeded the interrupt service routine gives up and generates a + warning message "eth0: Too much work in interrupt". + +hw_checksums=N1,N2,N3,... + + Recent 3com NICs are able to generate IPv4, TCP and UDP checksums + in hardware. Linux has used the Rx checksumming for a long time. + The "zero copy" patch which is planned for the 2.4 kernel series + allows you to make use of the NIC's DMA scatter/gather and transmit + checksumming as well. + + The driver is set up so that, when the zerocopy patch is applied, + all Tornado and Cyclone devices will use S/G and Tx checksums. + + This module parameter has been provided so you can override this + decision. If you think that Tx checksums are causing a problem, you + may disable the feature with ``hw_checksums=0``. + + If you think your NIC should be performing Tx checksumming and the + driver isn't enabling it, you can force the use of hardware Tx + checksumming with ``hw_checksums=1``. + + The driver drops a message in the logfiles to indicate whether or + not it is using hardware scatter/gather and hardware Tx checksums. + + Scatter/gather and hardware checksums provide considerable + performance improvement for the sendfile() system call, but a small + decrease in throughput for send(). There is no effect upon receive + efficiency. + +compaq_ioaddr=N, +compaq_irq=N, +compaq_device_id=N + + "Variables to work-around the Compaq PCI BIOS32 problem".... + +watchdog=N + + Sets the time duration (in milliseconds) after which the kernel + decides that the transmitter has become stuck and needs to be reset. + This is mainly for debugging purposes, although it may be advantageous + to increase this value on LANs which have very high collision rates. + The default value is 5000 (5.0 seconds). + +enable_wol=N1,N2,N3,... + + Enable Wake-on-LAN support for the relevant interface. Donald + Becker's ``ether-wake`` application may be used to wake suspended + machines. + + Also enables the NIC's power management support. + +global_enable_wol=N + + Sets enable_wol mode for all 3c59x NICs in the machine. Entries in + the ``enable_wol`` array above will override any setting of this. + +Media selection +--------------- + +A number of the older NICs such as the 3c590 and 3c900 series have +10base2 and AUI interfaces. + +Prior to January, 2001 this driver would autoselect the 10base2 or AUI +port if it didn't detect activity on the 10baseT port. It would then +get stuck on the 10base2 port and a driver reload was necessary to +switch back to 10baseT. This behaviour could not be prevented with a +module option override. + +Later (current) versions of the driver _do_ support locking of the +media type. So if you load the driver module with + + modprobe 3c59x options=0 + +it will permanently select the 10baseT port. Automatic selection of +other media types does not occur. + + +Transmit error, Tx status register 82 +------------------------------------- + +This is a common error which is almost always caused by another host on +the same network being in full-duplex mode, while this host is in +half-duplex mode. You need to find that other host and make it run in +half-duplex mode or fix this host to run in full-duplex mode. + +As a last resort, you can force the 3c59x driver into full-duplex mode +with + + options 3c59x full_duplex=1 + +but this has to be viewed as a workaround for broken network gear and +should only really be used for equipment which cannot autonegotiate. + + +Additional resources +-------------------- + +Details of the device driver implementation are at the top of the source file. + +Additional documentation is available at Don Becker's Linux Drivers site: + + http://www.scyld.com/vortex.html + +Donald Becker's driver development site: + + http://www.scyld.com/network.html + +Donald's vortex-diag program is useful for inspecting the NIC's state: + + http://www.scyld.com/ethercard_diag.html + +Donald's mii-diag program may be used for inspecting and manipulating +the NIC's Media Independent Interface subsystem: + + http://www.scyld.com/ethercard_diag.html#mii-diag + +Donald's wake-on-LAN page: + + http://www.scyld.com/wakeonlan.html + +3Com's DOS-based application for setting up the NICs EEPROMs: + + ftp://ftp.3com.com/pub/nic/3c90x/3c90xx2.exe + + +Autonegotiation notes +--------------------- + + The driver uses a one-minute heartbeat for adapting to changes in + the external LAN environment if link is up and 5 seconds if link is down. + This means that when, for example, a machine is unplugged from a hubbed + 10baseT LAN plugged into a switched 100baseT LAN, the throughput + will be quite dreadful for up to sixty seconds. Be patient. + + Cisco interoperability note from Walter Wong <wcw+@CMU.EDU>: + + On a side note, adding HAS_NWAY seems to share a problem with the + Cisco 6509 switch. Specifically, you need to change the spanning + tree parameter for the port the machine is plugged into to 'portfast' + mode. Otherwise, the negotiation fails. This has been an issue + we've noticed for a while but haven't had the time to track down. + + Cisco switches (Jeff Busch <jbusch@deja.com>) + + My "standard config" for ports to which PC's/servers connect directly:: + + interface FastEthernet0/N + description machinename + load-interval 30 + spanning-tree portfast + + If autonegotiation is a problem, you may need to specify "speed + 100" and "duplex full" as well (or "speed 10" and "duplex half"). + + WARNING: DO NOT hook up hubs/switches/bridges to these + specially-configured ports! The switch will become very confused. + + +Reporting and diagnosing problems +--------------------------------- + +Maintainers find that accurate and complete problem reports are +invaluable in resolving driver problems. We are frequently not able to +reproduce problems and must rely on your patience and efforts to get to +the bottom of the problem. + +If you believe you have a driver problem here are some of the +steps you should take: + +- Is it really a driver problem? + + Eliminate some variables: try different cards, different + computers, different cables, different ports on the switch/hub, + different versions of the kernel or of the driver, etc. + +- OK, it's a driver problem. + + You need to generate a report. Typically this is an email to the + maintainer and/or netdev@vger.kernel.org. The maintainer's + email address will be in the driver source or in the MAINTAINERS file. + +- The contents of your report will vary a lot depending upon the + problem. If it's a kernel crash then you should refer to + 'Documentation/admin-guide/reporting-issues.rst'. + + But for most problems it is useful to provide the following: + + - Kernel version, driver version + + - A copy of the banner message which the driver generates when + it is initialised. For example: + + eth0: 3Com PCI 3c905C Tornado at 0xa400, 00:50:da:6a:88:f0, IRQ 19 + 8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface. + MII transceiver found at address 24, status 782d. + Enabling bus-master transmits and whole-frame receives. + + NOTE: You must provide the ``debug=2`` modprobe option to generate + a full detection message. Please do this:: + + modprobe 3c59x debug=2 + + - If it is a PCI device, the relevant output from 'lspci -vx', eg:: + + 00:09.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 74) + Subsystem: 3Com Corporation: Unknown device 9200 + Flags: bus master, medium devsel, latency 32, IRQ 19 + I/O ports at a400 [size=128] + Memory at db000000 (32-bit, non-prefetchable) [size=128] + Expansion ROM at <unassigned> [disabled] [size=128K] + Capabilities: [dc] Power Management version 2 + 00: b7 10 00 92 07 00 10 02 74 00 00 02 08 20 00 00 + 10: 01 a4 00 00 00 00 00 db 00 00 00 00 00 00 00 00 + 20: 00 00 00 00 00 00 00 00 00 00 00 00 b7 10 00 10 + 30: 00 00 00 00 dc 00 00 00 00 00 00 00 05 01 0a 0a + + - A description of the environment: 10baseT? 100baseT? + full/half duplex? switched or hubbed? + + - Any additional module parameters which you may be providing to the driver. + + - Any kernel logs which are produced. The more the merrier. + If this is a large file and you are sending your report to a + mailing list, mention that you have the logfile, but don't send + it. If you're reporting direct to the maintainer then just send + it. + + To ensure that all kernel logs are available, add the + following line to /etc/syslog.conf:: + + kern.* /var/log/messages + + Then restart syslogd with:: + + /etc/rc.d/init.d/syslog restart + + (The above may vary, depending upon which Linux distribution you use). + + - If your problem is reproducible then that's great. Try the + following: + + 1) Increase the debug level. Usually this is done via: + + a) modprobe driver debug=7 + b) In /etc/modprobe.d/driver.conf: + options driver debug=7 + + 2) Recreate the problem with the higher debug level, + send all logs to the maintainer. + + 3) Download you card's diagnostic tool from Donald + Becker's website <http://www.scyld.com/ethercard_diag.html>. + Download mii-diag.c as well. Build these. + + a) Run 'vortex-diag -aaee' and 'mii-diag -v' when the card is + working correctly. Save the output. + + b) Run the above commands when the card is malfunctioning. Send + both sets of output. + +Finally, please be patient and be prepared to do some work. You may +end up working on this problem for a week or more as the maintainer +asks more questions, asks for more tests, asks for patches to be +applied, etc. At the end of it all, the problem may even remain +unresolved. diff --git a/Documentation/networking/device_drivers/ethernet/altera/altera_tse.rst b/Documentation/networking/device_drivers/ethernet/altera/altera_tse.rst new file mode 100644 index 0000000000..7a7040072e --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/altera/altera_tse.rst @@ -0,0 +1,286 @@ +.. SPDX-License-Identifier: GPL-2.0 + +.. include:: <isonum.txt> + +======================================= +Altera Triple-Speed Ethernet MAC driver +======================================= + +Copyright |copy| 2008-2014 Altera Corporation + +This is the driver for the Altera Triple-Speed Ethernet (TSE) controllers +using the SGDMA and MSGDMA soft DMA IP components. The driver uses the +platform bus to obtain component resources. The designs used to test this +driver were built for a Cyclone(R) V SOC FPGA board, a Cyclone(R) V FPGA board, +and tested with ARM and NIOS processor hosts separately. The anticipated use +cases are simple communications between an embedded system and an external peer +for status and simple configuration of the embedded system. + +For more information visit www.altera.com and www.rocketboards.org. Support +forums for the driver may be found on www.rocketboards.org, and a design used +to test this driver may be found there as well. Support is also available from +the maintainer of this driver, found in MAINTAINERS. + +The Triple-Speed Ethernet, SGDMA, and MSGDMA components are all soft IP +components that can be assembled and built into an FPGA using the Altera +Quartus toolchain. Quartus 13.1 and 14.0 were used to build the design that +this driver was tested against. The sopc2dts tool is used to create the +device tree for the driver, and may be found at rocketboards.org. + +The driver probe function examines the device tree and determines if the +Triple-Speed Ethernet instance is using an SGDMA or MSGDMA component. The +probe function then installs the appropriate set of DMA routines to +initialize, setup transmits, receives, and interrupt handling primitives for +the respective configurations. + +The SGDMA component is to be deprecated in the near future (over the next 1-2 +years as of this writing in early 2014) in favor of the MSGDMA component. +SGDMA support is included for existing designs and reference in case a +developer wishes to support their own soft DMA logic and driver support. Any +new designs should not use the SGDMA. + +The SGDMA supports only a single transmit or receive operation at a time, and +therefore will not perform as well compared to the MSGDMA soft IP. Please +visit www.altera.com for known, documented SGDMA errata. + +Scatter-gather DMA is not supported by the SGDMA or MSGDMA at this time. +Scatter-gather DMA will be added to a future maintenance update to this +driver. + +Jumbo frames are not supported at this time. + +The driver limits PHY operations to 10/100Mbps, and has not yet been fully +tested for 1Gbps. This support will be added in a future maintenance update. + +1. Kernel Configuration +======================= + +The kernel configuration option is ALTERA_TSE: + + Device Drivers ---> Network device support ---> Ethernet driver support ---> + Altera Triple-Speed Ethernet MAC support (ALTERA_TSE) + +2. Driver parameters list +========================= + + - debug: message level (0: no output, 16: all); + - dma_rx_num: Number of descriptors in the RX list (default is 64); + - dma_tx_num: Number of descriptors in the TX list (default is 64). + +3. Command line options +======================= + +Driver parameters can be also passed in command line by using:: + + altera_tse=dma_rx_num:128,dma_tx_num:512 + +4. Driver information and notes +=============================== + +4.1. Transmit process +--------------------- +When the driver's transmit routine is called by the kernel, it sets up a +transmit descriptor by calling the underlying DMA transmit routine (SGDMA or +MSGDMA), and initiates a transmit operation. Once the transmit is complete, an +interrupt is driven by the transmit DMA logic. The driver handles the transmit +completion in the context of the interrupt handling chain by recycling +resource required to send and track the requested transmit operation. + +4.2. Receive process +-------------------- +The driver will post receive buffers to the receive DMA logic during driver +initialization. Receive buffers may or may not be queued depending upon the +underlying DMA logic (MSGDMA is able queue receive buffers, SGDMA is not able +to queue receive buffers to the SGDMA receive logic). When a packet is +received, the DMA logic generates an interrupt. The driver handles a receive +interrupt by obtaining the DMA receive logic status, reaping receive +completions until no more receive completions are available. + +4.3. Interrupt Mitigation +------------------------- +The driver is able to mitigate the number of its DMA interrupts +using NAPI for receive operations. Interrupt mitigation is not yet supported +for transmit operations, but will be added in a future maintenance release. + +4.4) Ethtool support +-------------------- +Ethtool is supported. Driver statistics and internal errors can be taken using: +ethtool -S ethX command. It is possible to dump registers etc. + +4.5) PHY Support +---------------- +The driver is compatible with PAL to work with PHY and GPHY devices. + +4.7) List of source files: +-------------------------- + - Kconfig + - Makefile + - altera_tse_main.c: main network device driver + - altera_tse_ethtool.c: ethtool support + - altera_tse.h: private driver structure and common definitions + - altera_msgdma.h: MSGDMA implementation function definitions + - altera_sgdma.h: SGDMA implementation function definitions + - altera_msgdma.c: MSGDMA implementation + - altera_sgdma.c: SGDMA implementation + - altera_sgdmahw.h: SGDMA register and descriptor definitions + - altera_msgdmahw.h: MSGDMA register and descriptor definitions + - altera_utils.c: Driver utility functions + - altera_utils.h: Driver utility function definitions + +5. Debug Information +==================== + +The driver exports debug information such as internal statistics, +debug information, MAC and DMA registers etc. + +A user may use the ethtool support to get statistics: +e.g. using: ethtool -S ethX (that shows the statistics counters) +or sees the MAC registers: e.g. using: ethtool -d ethX + +The developer can also use the "debug" module parameter to get +further debug information. + +6. Statistics Support +===================== + +The controller and driver support a mix of IEEE standard defined statistics, +RFC defined statistics, and driver or Altera defined statistics. The four +specifications containing the standard definitions for these statistics are +as follows: + + - IEEE 802.3-2012 - IEEE Standard for Ethernet. + - RFC 2863 found at http://www.rfc-editor.org/rfc/rfc2863.txt. + - RFC 2819 found at http://www.rfc-editor.org/rfc/rfc2819.txt. + - Altera Triple Speed Ethernet User Guide, found at http://www.altera.com + +The statistics supported by the TSE and the device driver are as follows: + +"tx_packets" is equivalent to aFramesTransmittedOK defined in IEEE 802.3-2012, +Section 5.2.2.1.2. This statistics is the count of frames that are successfully +transmitted. + +"rx_packets" is equivalent to aFramesReceivedOK defined in IEEE 802.3-2012, +Section 5.2.2.1.5. This statistic is the count of frames that are successfully +received. This count does not include any error packets such as CRC errors, +length errors, or alignment errors. + +"rx_crc_errors" is equivalent to aFrameCheckSequenceErrors defined in IEEE +802.3-2012, Section 5.2.2.1.6. This statistic is the count of frames that are +an integral number of bytes in length and do not pass the CRC test as the frame +is received. + +"rx_align_errors" is equivalent to aAlignmentErrors defined in IEEE 802.3-2012, +Section 5.2.2.1.7. This statistic is the count of frames that are not an +integral number of bytes in length and do not pass the CRC test as the frame is +received. + +"tx_bytes" is equivalent to aOctetsTransmittedOK defined in IEEE 802.3-2012, +Section 5.2.2.1.8. This statistic is the count of data and pad bytes +successfully transmitted from the interface. + +"rx_bytes" is equivalent to aOctetsReceivedOK defined in IEEE 802.3-2012, +Section 5.2.2.1.14. This statistic is the count of data and pad bytes +successfully received by the controller. + +"tx_pause" is equivalent to aPAUSEMACCtrlFramesTransmitted defined in IEEE +802.3-2012, Section 30.3.4.2. This statistic is a count of PAUSE frames +transmitted from the network controller. + +"rx_pause" is equivalent to aPAUSEMACCtrlFramesReceived defined in IEEE +802.3-2012, Section 30.3.4.3. This statistic is a count of PAUSE frames +received by the network controller. + +"rx_errors" is equivalent to ifInErrors defined in RFC 2863. This statistic is +a count of the number of packets received containing errors that prevented the +packet from being delivered to a higher level protocol. + +"tx_errors" is equivalent to ifOutErrors defined in RFC 2863. This statistic +is a count of the number of packets that could not be transmitted due to errors. + +"rx_unicast" is equivalent to ifInUcastPkts defined in RFC 2863. This +statistic is a count of the number of packets received that were not addressed +to the broadcast address or a multicast group. + +"rx_multicast" is equivalent to ifInMulticastPkts defined in RFC 2863. This +statistic is a count of the number of packets received that were addressed to +a multicast address group. + +"rx_broadcast" is equivalent to ifInBroadcastPkts defined in RFC 2863. This +statistic is a count of the number of packets received that were addressed to +the broadcast address. + +"tx_discards" is equivalent to ifOutDiscards defined in RFC 2863. This +statistic is the number of outbound packets not transmitted even though an +error was not detected. An example of a reason this might occur is to free up +internal buffer space. + +"tx_unicast" is equivalent to ifOutUcastPkts defined in RFC 2863. This +statistic counts the number of packets transmitted that were not addressed to +a multicast group or broadcast address. + +"tx_multicast" is equivalent to ifOutMulticastPkts defined in RFC 2863. This +statistic counts the number of packets transmitted that were addressed to a +multicast group. + +"tx_broadcast" is equivalent to ifOutBroadcastPkts defined in RFC 2863. This +statistic counts the number of packets transmitted that were addressed to a +broadcast address. + +"ether_drops" is equivalent to etherStatsDropEvents defined in RFC 2819. +This statistic counts the number of packets dropped due to lack of internal +controller resources. + +"rx_total_bytes" is equivalent to etherStatsOctets defined in RFC 2819. +This statistic counts the total number of bytes received by the controller, +including error and discarded packets. + +"rx_total_packets" is equivalent to etherStatsPkts defined in RFC 2819. +This statistic counts the total number of packets received by the controller, +including error, discarded, unicast, multicast, and broadcast packets. + +"rx_undersize" is equivalent to etherStatsUndersizePkts defined in RFC 2819. +This statistic counts the number of correctly formed packets received less +than 64 bytes long. + +"rx_oversize" is equivalent to etherStatsOversizePkts defined in RFC 2819. +This statistic counts the number of correctly formed packets greater than 1518 +bytes long. + +"rx_64_bytes" is equivalent to etherStatsPkts64Octets defined in RFC 2819. +This statistic counts the total number of packets received that were 64 octets +in length. + +"rx_65_127_bytes" is equivalent to etherStatsPkts65to127Octets defined in RFC +2819. This statistic counts the total number of packets received that were +between 65 and 127 octets in length inclusive. + +"rx_128_255_bytes" is equivalent to etherStatsPkts128to255Octets defined in +RFC 2819. This statistic is the total number of packets received that were +between 128 and 255 octets in length inclusive. + +"rx_256_511_bytes" is equivalent to etherStatsPkts256to511Octets defined in +RFC 2819. This statistic is the total number of packets received that were +between 256 and 511 octets in length inclusive. + +"rx_512_1023_bytes" is equivalent to etherStatsPkts512to1023Octets defined in +RFC 2819. This statistic is the total number of packets received that were +between 512 and 1023 octets in length inclusive. + +"rx_1024_1518_bytes" is equivalent to etherStatsPkts1024to1518Octets define +in RFC 2819. This statistic is the total number of packets received that were +between 1024 and 1518 octets in length inclusive. + +"rx_gte_1519_bytes" is a statistic defined specific to the behavior of the +Altera TSE. This statistics counts the number of received good and errored +frames between the length of 1519 and the maximum frame length configured +in the frm_length register. See the Altera TSE User Guide for More details. + +"rx_jabbers" is equivalent to etherStatsJabbers defined in RFC 2819. This +statistic is the total number of packets received that were longer than 1518 +octets, and had either a bad CRC with an integral number of octets (CRC Error) +or a bad CRC with a non-integral number of octets (Alignment Error). + +"rx_runts" is equivalent to etherStatsFragments defined in RFC 2819. This +statistic is the total number of packets received that were less than 64 octets +in length and had either a bad CRC with an integral number of octets (CRC +error) or a bad CRC with a non-integral number of octets (Alignment Error). diff --git a/Documentation/networking/device_drivers/ethernet/amazon/ena.rst b/Documentation/networking/device_drivers/ethernet/amazon/ena.rst new file mode 100644 index 0000000000..5eaa3ab6c7 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/amazon/ena.rst @@ -0,0 +1,351 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============================================================ +Linux kernel driver for Elastic Network Adapter (ENA) family +============================================================ + +Overview +======== + +ENA is a networking interface designed to make good use of modern CPU +features and system architectures. + +The ENA device exposes a lightweight management interface with a +minimal set of memory mapped registers and extendible command set +through an Admin Queue. + +The driver supports a range of ENA devices, is link-speed independent +(i.e., the same driver is used for 10GbE, 25GbE, 40GbE, etc), and has +a negotiated and extendible feature set. + +Some ENA devices support SR-IOV. This driver is used for both the +SR-IOV Physical Function (PF) and Virtual Function (VF) devices. + +ENA devices enable high speed and low overhead network traffic +processing by providing multiple Tx/Rx queue pairs (the maximum number +is advertised by the device via the Admin Queue), a dedicated MSI-X +interrupt vector per Tx/Rx queue pair, adaptive interrupt moderation, +and CPU cacheline optimized data placement. + +The ENA driver supports industry standard TCP/IP offload features such as +checksum offload. Receive-side scaling (RSS) is supported for multi-core +scaling. + +The ENA driver and its corresponding devices implement health +monitoring mechanisms such as watchdog, enabling the device and driver +to recover in a manner transparent to the application, as well as +debug logs. + +Some of the ENA devices support a working mode called Low-latency +Queue (LLQ), which saves several more microseconds. + +ENA Source Code Directory Structure +=================================== + +================= ====================================================== +ena_com.[ch] Management communication layer. This layer is + responsible for the handling all the management + (admin) communication between the device and the + driver. +ena_eth_com.[ch] Tx/Rx data path. +ena_admin_defs.h Definition of ENA management interface. +ena_eth_io_defs.h Definition of ENA data path interface. +ena_common_defs.h Common definitions for ena_com layer. +ena_regs_defs.h Definition of ENA PCI memory-mapped (MMIO) registers. +ena_netdev.[ch] Main Linux kernel driver. +ena_ethtool.c ethtool callbacks. +ena_pci_id_tbl.h Supported device IDs. +================= ====================================================== + +Management Interface: +===================== + +ENA management interface is exposed by means of: + +- PCIe Configuration Space +- Device Registers +- Admin Queue (AQ) and Admin Completion Queue (ACQ) +- Asynchronous Event Notification Queue (AENQ) + +ENA device MMIO Registers are accessed only during driver +initialization and are not used during further normal device +operation. + +AQ is used for submitting management commands, and the +results/responses are reported asynchronously through ACQ. + +ENA introduces a small set of management commands with room for +vendor-specific extensions. Most of the management operations are +framed in a generic Get/Set feature command. + +The following admin queue commands are supported: + +- Create I/O submission queue +- Create I/O completion queue +- Destroy I/O submission queue +- Destroy I/O completion queue +- Get feature +- Set feature +- Configure AENQ +- Get statistics + +Refer to ena_admin_defs.h for the list of supported Get/Set Feature +properties. + +The Asynchronous Event Notification Queue (AENQ) is a uni-directional +queue used by the ENA device to send to the driver events that cannot +be reported using ACQ. AENQ events are subdivided into groups. Each +group may have multiple syndromes, as shown below + +The events are: + +==================== =============== +Group Syndrome +==================== =============== +Link state change **X** +Fatal error **X** +Notification Suspend traffic +Notification Resume traffic +Keep-Alive **X** +==================== =============== + +ACQ and AENQ share the same MSI-X vector. + +Keep-Alive is a special mechanism that allows monitoring the device's health. +A Keep-Alive event is delivered by the device every second. +The driver maintains a watchdog (WD) handler which logs the current state and +statistics. If the keep-alive events aren't delivered as expected the WD resets +the device and the driver. + +Data Path Interface +=================== + +I/O operations are based on Tx and Rx Submission Queues (Tx SQ and Rx +SQ correspondingly). Each SQ has a completion queue (CQ) associated +with it. + +The SQs and CQs are implemented as descriptor rings in contiguous +physical memory. + +The ENA driver supports two Queue Operation modes for Tx SQs: + +- **Regular mode:** + In this mode the Tx SQs reside in the host's memory. The ENA + device fetches the ENA Tx descriptors and packet data from host + memory. + +- **Low Latency Queue (LLQ) mode or "push-mode":** + In this mode the driver pushes the transmit descriptors and the + first 96 bytes of the packet directly to the ENA device memory + space. The rest of the packet payload is fetched by the + device. For this operation mode, the driver uses a dedicated PCI + device memory BAR, which is mapped with write-combine capability. + + **Note that** not all ENA devices support LLQ, and this feature is negotiated + with the device upon initialization. If the ENA device does not + support LLQ mode, the driver falls back to the regular mode. + +The Rx SQs support only the regular mode. + +The driver supports multi-queue for both Tx and Rx. This has various +benefits: + +- Reduced CPU/thread/process contention on a given Ethernet interface. +- Cache miss rate on completion is reduced, particularly for data + cache lines that hold the sk_buff structures. +- Increased process-level parallelism when handling received packets. +- Increased data cache hit rate, by steering kernel processing of + packets to the CPU, where the application thread consuming the + packet is running. +- In hardware interrupt re-direction. + +Interrupt Modes +=============== + +The driver assigns a single MSI-X vector per queue pair (for both Tx +and Rx directions). The driver assigns an additional dedicated MSI-X vector +for management (for ACQ and AENQ). + +Management interrupt registration is performed when the Linux kernel +probes the adapter, and it is de-registered when the adapter is +removed. I/O queue interrupt registration is performed when the Linux +interface of the adapter is opened, and it is de-registered when the +interface is closed. + +The management interrupt is named:: + + ena-mgmnt@pci:<PCI domain:bus:slot.function> + +and for each queue pair, an interrupt is named:: + + <interface name>-Tx-Rx-<queue index> + +The ENA device operates in auto-mask and auto-clear interrupt +modes. That is, once MSI-X is delivered to the host, its Cause bit is +automatically cleared and the interrupt is masked. The interrupt is +unmasked by the driver after NAPI processing is complete. + +Interrupt Moderation +==================== + +ENA driver and device can operate in conventional or adaptive interrupt +moderation mode. + +**In conventional mode** the driver instructs device to postpone interrupt +posting according to static interrupt delay value. The interrupt delay +value can be configured through `ethtool(8)`. The following `ethtool` +parameters are supported by the driver: ``tx-usecs``, ``rx-usecs`` + +**In adaptive interrupt** moderation mode the interrupt delay value is +updated by the driver dynamically and adjusted every NAPI cycle +according to the traffic nature. + +Adaptive coalescing can be switched on/off through `ethtool(8)`'s +:code:`adaptive_rx on|off` parameter. + +More information about Adaptive Interrupt Moderation (DIM) can be found in +Documentation/networking/net_dim.rst + +.. _`RX copybreak`: + +RX copybreak +============ +The rx_copybreak is initialized by default to ENA_DEFAULT_RX_COPYBREAK +and can be configured by the ETHTOOL_STUNABLE command of the +SIOCETHTOOL ioctl. + +Statistics +========== + +The user can obtain ENA device and driver statistics using `ethtool`. +The driver can collect regular or extended statistics (including +per-queue stats) from the device. + +In addition the driver logs the stats to syslog upon device reset. + +MTU +=== + +The driver supports an arbitrarily large MTU with a maximum that is +negotiated with the device. The driver configures MTU using the +SetFeature command (ENA_ADMIN_MTU property). The user can change MTU +via `ip(8)` and similar legacy tools. + +Stateless Offloads +================== + +The ENA driver supports: + +- IPv4 header checksum offload +- TCP/UDP over IPv4/IPv6 checksum offloads + +RSS +=== + +- The ENA device supports RSS that allows flexible Rx traffic + steering. +- Toeplitz and CRC32 hash functions are supported. +- Different combinations of L2/L3/L4 fields can be configured as + inputs for hash functions. +- The driver configures RSS settings using the AQ SetFeature command + (ENA_ADMIN_RSS_HASH_FUNCTION, ENA_ADMIN_RSS_HASH_INPUT and + ENA_ADMIN_RSS_INDIRECTION_TABLE_CONFIG properties). +- If the NETIF_F_RXHASH flag is set, the 32-bit result of the hash + function delivered in the Rx CQ descriptor is set in the received + SKB. +- The user can provide a hash key, hash function, and configure the + indirection table through `ethtool(8)`. + +DATA PATH +========= + +Tx +-- + +:code:`ena_start_xmit()` is called by the stack. This function does the following: + +- Maps data buffers (``skb->data`` and frags). +- Populates ``ena_buf`` for the push buffer (if the driver and device are + in push mode). +- Prepares ENA bufs for the remaining frags. +- Allocates a new request ID from the empty ``req_id`` ring. The request + ID is the index of the packet in the Tx info. This is used for + out-of-order Tx completions. +- Adds the packet to the proper place in the Tx ring. +- Calls :code:`ena_com_prepare_tx()`, an ENA communication layer that converts + the ``ena_bufs`` to ENA descriptors (and adds meta ENA descriptors as + needed). + + * This function also copies the ENA descriptors and the push buffer + to the Device memory space (if in push mode). + +- Writes a doorbell to the ENA device. +- When the ENA device finishes sending the packet, a completion + interrupt is raised. +- The interrupt handler schedules NAPI. +- The :code:`ena_clean_tx_irq()` function is called. This function handles the + completion descriptors generated by the ENA, with a single + completion descriptor per completed packet. + + * ``req_id`` is retrieved from the completion descriptor. The ``tx_info`` of + the packet is retrieved via the ``req_id``. The data buffers are + unmapped and ``req_id`` is returned to the empty ``req_id`` ring. + * The function stops when the completion descriptors are completed or + the budget is reached. + +Rx +-- + +- When a packet is received from the ENA device. +- The interrupt handler schedules NAPI. +- The :code:`ena_clean_rx_irq()` function is called. This function calls + :code:`ena_com_rx_pkt()`, an ENA communication layer function, which returns the + number of descriptors used for a new packet, and zero if + no new packet is found. +- :code:`ena_rx_skb()` checks packet length: + + * If the packet is small (len < rx_copybreak), the driver allocates + a SKB for the new packet, and copies the packet payload into the + SKB data buffer. + + - In this way the original data buffer is not passed to the stack + and is reused for future Rx packets. + + * Otherwise the function unmaps the Rx buffer, sets the first + descriptor as `skb`'s linear part and the other descriptors as the + `skb`'s frags. + +- The new SKB is updated with the necessary information (protocol, + checksum hw verify result, etc), and then passed to the network + stack, using the NAPI interface function :code:`napi_gro_receive()`. + +Dynamic RX Buffers (DRB) +------------------------ + +Each RX descriptor in the RX ring is a single memory page (which is either 4KB +or 16KB long depending on system's configurations). +To reduce the memory allocations required when dealing with a high rate of small +packets, the driver tries to reuse the remaining RX descriptor's space if more +than 2KB of this page remain unused. + +A simple example of this mechanism is the following sequence of events: + +:: + + 1. Driver allocates page-sized RX buffer and passes it to hardware + +----------------------+ + |4KB RX Buffer | + +----------------------+ + + 2. A 300Bytes packet is received on this buffer + + 3. The driver increases the ref count on this page and returns it back to + HW as an RX buffer of size 4KB - 300Bytes = 3796 Bytes + +----+--------------------+ + |****|3796 Bytes RX Buffer| + +----+--------------------+ + +This mechanism isn't used when an XDP program is loaded, or when the +RX packet is less than rx_copybreak bytes (in which case the packet is +copied out of the RX buffer into the linear part of a new skb allocated +for it and the RX buffer remains the same size, see `RX copybreak`_). diff --git a/Documentation/networking/device_drivers/ethernet/amd/pds_core.rst b/Documentation/networking/device_drivers/ethernet/amd/pds_core.rst new file mode 100644 index 0000000000..9e8a16c441 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/amd/pds_core.rst @@ -0,0 +1,139 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +======================================================== +Linux Driver for the AMD/Pensando(R) DSC adapter family +======================================================== + +Copyright(c) 2023 Advanced Micro Devices, Inc + +Identifying the Adapter +======================= + +To find if one or more AMD/Pensando PCI Core devices are installed on the +host, check for the PCI devices:: + + # lspci -d 1dd8:100c + b5:00.0 Processing accelerators: Pensando Systems Device 100c + b6:00.0 Processing accelerators: Pensando Systems Device 100c + +If such devices are listed as above, then the pds_core.ko driver should find +and configure them for use. There should be log entries in the kernel +messages such as these:: + + $ dmesg | grep pds_core + pds_core 0000:b5:00.0: 252.048 Gb/s available PCIe bandwidth (16.0 GT/s PCIe x16 link) + pds_core 0000:b5:00.0: FW: 1.60.0-73 + pds_core 0000:b6:00.0: 252.048 Gb/s available PCIe bandwidth (16.0 GT/s PCIe x16 link) + pds_core 0000:b6:00.0: FW: 1.60.0-73 + +Driver and firmware version information can be gathered with devlink:: + + $ devlink dev info pci/0000:b5:00.0 + pci/0000:b5:00.0: + driver pds_core + serial_number FLM18420073 + versions: + fixed: + asic.id 0x0 + asic.rev 0x0 + running: + fw 1.51.0-73 + stored: + fw.goldfw 1.15.9-C-22 + fw.mainfwa 1.60.0-73 + fw.mainfwb 1.60.0-57 + +Info versions +============= + +The ``pds_core`` driver reports the following versions + +.. list-table:: devlink info versions implemented + :widths: 5 5 90 + + * - Name + - Type + - Description + * - ``fw`` + - running + - Version of firmware running on the device + * - ``fw.goldfw`` + - stored + - Version of firmware stored in the goldfw slot + * - ``fw.mainfwa`` + - stored + - Version of firmware stored in the mainfwa slot + * - ``fw.mainfwb`` + - stored + - Version of firmware stored in the mainfwb slot + * - ``asic.id`` + - fixed + - The ASIC type for this device + * - ``asic.rev`` + - fixed + - The revision of the ASIC for this device + +Parameters +========== + +The ``pds_core`` driver implements the following generic +parameters for controlling the functionality to be made available +as auxiliary_bus devices. + +.. list-table:: Generic parameters implemented + :widths: 5 5 8 82 + + * - Name + - Mode + - Type + - Description + * - ``enable_vnet`` + - runtime + - Boolean + - Enables vDPA functionality through an auxiliary_bus device + +Firmware Management +=================== + +The ``flash`` command can update a the DSC firmware. The downloaded firmware +will be saved into either of firmware bank 1 or bank 2, whichever is not +currently in use, and that bank will used for the next boot:: + + # devlink dev flash pci/0000:b5:00.0 \ + file pensando/dsc_fw_1.63.0-22.tar + +Health Reporters +================ + +The driver supports a devlink health reporter for FW status:: + + # devlink health show pci/0000:2b:00.0 reporter fw + pci/0000:2b:00.0: + reporter fw + state healthy error 0 recover 0 + # devlink health diagnose pci/0000:2b:00.0 reporter fw + Status: healthy State: 1 Generation: 0 Recoveries: 0 + +Enabling the driver +=================== + +The driver is enabled via the standard kernel configuration system, +using the make command:: + + make oldconfig/menuconfig/etc. + +The driver is located in the menu structure at: + + -> Device Drivers + -> Network device support (NETDEVICES [=y]) + -> Ethernet driver support + -> AMD devices + -> AMD/Pensando Ethernet PDS_CORE Support + +Support +======= + +For general Linux networking support, please use the netdev mailing +list, which is monitored by AMD/Pensando personnel:: + + netdev@vger.kernel.org diff --git a/Documentation/networking/device_drivers/ethernet/amd/pds_vdpa.rst b/Documentation/networking/device_drivers/ethernet/amd/pds_vdpa.rst new file mode 100644 index 0000000000..587927d3de --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/amd/pds_vdpa.rst @@ -0,0 +1,85 @@ +.. SPDX-License-Identifier: GPL-2.0+ +.. note: can be edited and viewed with /usr/bin/formiko-vim + +========================================================== +PCI vDPA driver for the AMD/Pensando(R) DSC adapter family +========================================================== + +AMD/Pensando vDPA VF Device Driver + +Copyright(c) 2023 Advanced Micro Devices, Inc + +Overview +======== + +The ``pds_vdpa`` driver is an auxiliary bus driver that supplies +a vDPA device for use by the virtio network stack. It is used with +the Pensando Virtual Function devices that offer vDPA and virtio queue +services. It depends on the ``pds_core`` driver and hardware for the PF +and VF PCI handling as well as for device configuration services. + +Using the device +================ + +The ``pds_vdpa`` device is enabled via multiple configuration steps and +depends on the ``pds_core`` driver to create and enable SR-IOV Virtual +Function devices. After the VFs are enabled, we enable the vDPA service +in the ``pds_core`` device to create the auxiliary devices used by pds_vdpa. + +Example steps: + +.. code-block:: bash + + #!/bin/bash + + modprobe pds_core + modprobe vdpa + modprobe pds_vdpa + + PF_BDF=`ls /sys/module/pds_core/drivers/pci\:pds_core/*/sriov_numvfs | awk -F / '{print $7}'` + + # Enable vDPA VF auxiliary device(s) in the PF + devlink dev param set pci/$PF_BDF name enable_vnet cmode runtime value true + + # Create a VF for vDPA use + echo 1 > /sys/bus/pci/drivers/pds_core/$PF_BDF/sriov_numvfs + + # Find the vDPA services/devices available + PDS_VDPA_MGMT=`vdpa mgmtdev show | grep vDPA | head -1 | cut -d: -f1` + + # Create a vDPA device for use in virtio network configurations + vdpa dev add name vdpa1 mgmtdev $PDS_VDPA_MGMT mac 00:11:22:33:44:55 + + # Set up an ethernet interface on the vdpa device + modprobe virtio_vdpa + + + +Enabling the driver +=================== + +The driver is enabled via the standard kernel configuration system, +using the make command:: + + make oldconfig/menuconfig/etc. + +The driver is located in the menu structure at: + + -> Device Drivers + -> Network device support (NETDEVICES [=y]) + -> Ethernet driver support + -> Pensando devices + -> Pensando Ethernet PDS_VDPA Support + +Support +======= + +For general Linux networking support, please use the netdev mailing +list, which is monitored by Pensando personnel:: + + netdev@vger.kernel.org + +For more specific support needs, please use the Pensando driver support +email:: + + drivers@pensando.io diff --git a/Documentation/networking/device_drivers/ethernet/amd/pds_vfio_pci.rst b/Documentation/networking/device_drivers/ethernet/amd/pds_vfio_pci.rst new file mode 100644 index 0000000000..7a6bc848a2 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/amd/pds_vfio_pci.rst @@ -0,0 +1,79 @@ +.. SPDX-License-Identifier: GPL-2.0+ +.. note: can be edited and viewed with /usr/bin/formiko-vim + +========================================================== +PCI VFIO driver for the AMD/Pensando(R) DSC adapter family +========================================================== + +AMD/Pensando Linux VFIO PCI Device Driver +Copyright(c) 2023 Advanced Micro Devices, Inc. + +Overview +======== + +The ``pds-vfio-pci`` module is a PCI driver that supports Live Migration +capable Virtual Function (VF) devices in the DSC hardware. + +Using the device +================ + +The pds-vfio-pci device is enabled via multiple configuration steps and +depends on the ``pds_core`` driver to create and enable SR-IOV Virtual +Function devices. + +Shown below are the steps to bind the driver to a VF and also to the +associated auxiliary device created by the ``pds_core`` driver. This +example assumes the pds_core and pds-vfio-pci modules are already +loaded. + +.. code-block:: bash + :name: example-setup-script + + #!/bin/bash + + PF_BUS="0000:60" + PF_BDF="0000:60:00.0" + VF_BDF="0000:60:00.1" + + # Prevent non-vfio VF driver from probing the VF device + echo 0 > /sys/class/pci_bus/$PF_BUS/device/$PF_BDF/sriov_drivers_autoprobe + + # Create single VF for Live Migration via pds_core + echo 1 > /sys/bus/pci/drivers/pds_core/$PF_BDF/sriov_numvfs + + # Allow the VF to be bound to the pds-vfio-pci driver + echo "pds-vfio-pci" > /sys/class/pci_bus/$PF_BUS/device/$VF_BDF/driver_override + + # Bind the VF to the pds-vfio-pci driver + echo "$VF_BDF" > /sys/bus/pci/drivers/pds-vfio-pci/bind + +After performing the steps above, a file in /dev/vfio/<iommu_group> +should have been created. + + +Enabling the driver +=================== + +The driver is enabled via the standard kernel configuration system, +using the make command:: + + make oldconfig/menuconfig/etc. + +The driver is located in the menu structure at: + + -> Device Drivers + -> VFIO Non-Privileged userspace driver framework + -> VFIO support for PDS PCI devices + +Support +======= + +For general Linux networking support, please use the netdev mailing +list, which is monitored by Pensando personnel:: + + netdev@vger.kernel.org + +For more specific support needs, please use the Pensando driver support +email:: + + drivers@pensando.io diff --git a/Documentation/networking/device_drivers/ethernet/aquantia/atlantic.rst b/Documentation/networking/device_drivers/ethernet/aquantia/atlantic.rst new file mode 100644 index 0000000000..099280a261 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/aquantia/atlantic.rst @@ -0,0 +1,556 @@ +.. SPDX-License-Identifier: GPL-2.0 +.. include:: <isonum.txt> + +=============================== +Marvell(Aquantia) AQtion Driver +=============================== + +For the aQuantia Multi-Gigabit PCI Express Family of Ethernet Adapters + +.. Contents + + - Identifying Your Adapter + - Configuration + - Supported ethtool options + - Command Line Parameters + - Config file parameters + - Support + - License + +Identifying Your Adapter +======================== + +The driver in this release is compatible with AQC-100, AQC-107, AQC-108 +based ethernet adapters. + + +SFP+ Devices (for AQC-100 based adapters) +----------------------------------------- + +This release tested with passive Direct Attach Cables (DAC) and SFP+/LC +Optical Transceiver. + +Configuration +============= + +Viewing Link Messages +--------------------- + Link messages will not be displayed to the console if the distribution is + restricting system messages. In order to see network driver link messages on + your console, set dmesg to eight by entering the following:: + + dmesg -n 8 + + .. note:: + + This setting is not saved across reboots. + +Jumbo Frames +------------ + The driver supports Jumbo Frames for all adapters. Jumbo Frames support is + enabled by changing the MTU to a value larger than the default of 1500. + The maximum value for the MTU is 16000. Use the `ip` command to + increase the MTU size. For example:: + + ip link set mtu 16000 dev enp1s0 + +ethtool +------- + The driver utilizes the ethtool interface for driver configuration and + diagnostics, as well as displaying statistical information. The latest + ethtool version is required for this functionality. + +NAPI +---- + NAPI (Rx polling mode) is supported in the atlantic driver. + +Supported ethtool options +========================= + +Viewing adapter settings +------------------------ + + :: + + ethtool <ethX> + + Output example:: + + Settings for enp1s0: + Supported ports: [ TP ] + Supported link modes: 100baseT/Full + 1000baseT/Full + 10000baseT/Full + 2500baseT/Full + 5000baseT/Full + Supported pause frame use: Symmetric + Supports auto-negotiation: Yes + Supported FEC modes: Not reported + Advertised link modes: 100baseT/Full + 1000baseT/Full + 10000baseT/Full + 2500baseT/Full + 5000baseT/Full + Advertised pause frame use: Symmetric + Advertised auto-negotiation: Yes + Advertised FEC modes: Not reported + Speed: 10000Mb/s + Duplex: Full + Port: Twisted Pair + PHYAD: 0 + Transceiver: internal + Auto-negotiation: on + MDI-X: Unknown + Supports Wake-on: g + Wake-on: d + Link detected: yes + + + .. note:: + + AQrate speeds (2.5/5 Gb/s) will be displayed only with linux kernels > 4.10. + But you can still use these speeds:: + + ethtool -s eth0 autoneg off speed 2500 + +Viewing adapter information +--------------------------- + + :: + + ethtool -i <ethX> + + Output example:: + + driver: atlantic + version: 5.2.0-050200rc5-generic-kern + firmware-version: 3.1.78 + expansion-rom-version: + bus-info: 0000:01:00.0 + supports-statistics: yes + supports-test: no + supports-eeprom-access: no + supports-register-dump: yes + supports-priv-flags: no + + +Viewing Ethernet adapter statistics +----------------------------------- + + :: + + ethtool -S <ethX> + + Output example:: + + NIC statistics: + InPackets: 13238607 + InUCast: 13293852 + InMCast: 52 + InBCast: 3 + InErrors: 0 + OutPackets: 23703019 + OutUCast: 23704941 + OutMCast: 67 + OutBCast: 11 + InUCastOctects: 213182760 + OutUCastOctects: 22698443 + InMCastOctects: 6600 + OutMCastOctects: 8776 + InBCastOctects: 192 + OutBCastOctects: 704 + InOctects: 2131839552 + OutOctects: 226938073 + InPacketsDma: 95532300 + OutPacketsDma: 59503397 + InOctetsDma: 1137102462 + OutOctetsDma: 2394339518 + InDroppedDma: 0 + Queue[0] InPackets: 23567131 + Queue[0] OutPackets: 20070028 + Queue[0] InJumboPackets: 0 + Queue[0] InLroPackets: 0 + Queue[0] InErrors: 0 + Queue[1] InPackets: 45428967 + Queue[1] OutPackets: 11306178 + Queue[1] InJumboPackets: 0 + Queue[1] InLroPackets: 0 + Queue[1] InErrors: 0 + Queue[2] InPackets: 3187011 + Queue[2] OutPackets: 13080381 + Queue[2] InJumboPackets: 0 + Queue[2] InLroPackets: 0 + Queue[2] InErrors: 0 + Queue[3] InPackets: 23349136 + Queue[3] OutPackets: 15046810 + Queue[3] InJumboPackets: 0 + Queue[3] InLroPackets: 0 + Queue[3] InErrors: 0 + +Interrupt coalescing support +---------------------------- + + ITR mode, TX/RX coalescing timings could be viewed with:: + + ethtool -c <ethX> + + and changed with:: + + ethtool -C <ethX> tx-usecs <usecs> rx-usecs <usecs> + + To disable coalescing:: + + ethtool -C <ethX> tx-usecs 0 rx-usecs 0 tx-max-frames 1 tx-max-frames 1 + +Wake on LAN support +------------------- + + WOL support by magic packet:: + + ethtool -s <ethX> wol g + + To disable WOL:: + + ethtool -s <ethX> wol d + +Set and check the driver message level +-------------------------------------- + + Set message level + + :: + + ethtool -s <ethX> msglvl <level> + + Level values: + + ====== ============================= + 0x0001 general driver status. + 0x0002 hardware probing. + 0x0004 link state. + 0x0008 periodic status check. + 0x0010 interface being brought down. + 0x0020 interface being brought up. + 0x0040 receive error. + 0x0080 transmit error. + 0x0200 interrupt handling. + 0x0400 transmit completion. + 0x0800 receive completion. + 0x1000 packet contents. + 0x2000 hardware status. + 0x4000 Wake-on-LAN status. + ====== ============================= + + By default, the level of debugging messages is set 0x0001(general driver status). + + Check message level + + :: + + ethtool <ethX> | grep "Current message level" + + If you want to disable the output of messages:: + + ethtool -s <ethX> msglvl 0 + +RX flow rules (ntuple filters) +------------------------------ + + There are separate rules supported, that applies in that order: + + 1. 16 VLAN ID rules + 2. 16 L2 EtherType rules + 3. 8 L3/L4 5-Tuple rules + + + The driver utilizes the ethtool interface for configuring ntuple filters, + via ``ethtool -N <device> <filter>``. + + To enable or disable the RX flow rules:: + + ethtool -K ethX ntuple <on|off> + + When disabling ntuple filters, all the user programmed filters are + flushed from the driver cache and hardware. All needed filters must + be re-added when ntuple is re-enabled. + + Because of the fixed order of the rules, the location of filters is also fixed: + + - Locations 0 - 15 for VLAN ID filters + - Locations 16 - 31 for L2 EtherType filters + - Locations 32 - 39 for L3/L4 5-tuple filters (locations 32, 36 for IPv6) + + The L3/L4 5-tuple (protocol, source and destination IP address, source and + destination TCP/UDP/SCTP port) is compared against 8 filters. For IPv4, up to + 8 source and destination addresses can be matched. For IPv6, up to 2 pairs of + addresses can be supported. Source and destination ports are only compared for + TCP/UDP/SCTP packets. + + To add a filter that directs packet to queue 5, use + ``<-N|-U|--config-nfc|--config-ntuple>`` switch:: + + ethtool -N <ethX> flow-type udp4 src-ip 10.0.0.1 dst-ip 10.0.0.2 src-port 2000 dst-port 2001 action 5 <loc 32> + + - action is the queue number. + - loc is the rule number. + + For ``flow-type ip4|udp4|tcp4|sctp4|ip6|udp6|tcp6|sctp6`` you must set the loc + number within 32 - 39. + For ``flow-type ip4|udp4|tcp4|sctp4|ip6|udp6|tcp6|sctp6`` you can set 8 rules + for traffic IPv4 or you can set 2 rules for traffic IPv6. Loc number traffic + IPv6 is 32 and 36. + At the moment you can not use IPv4 and IPv6 filters at the same time. + + Example filter for IPv6 filter traffic:: + + sudo ethtool -N <ethX> flow-type tcp6 src-ip 2001:db8:0:f101::1 dst-ip 2001:db8:0:f101::2 action 1 loc 32 + sudo ethtool -N <ethX> flow-type ip6 src-ip 2001:db8:0:f101::2 dst-ip 2001:db8:0:f101::5 action -1 loc 36 + + Example filter for IPv4 filter traffic:: + + sudo ethtool -N <ethX> flow-type udp4 src-ip 10.0.0.4 dst-ip 10.0.0.7 src-port 2000 dst-port 2001 loc 32 + sudo ethtool -N <ethX> flow-type tcp4 src-ip 10.0.0.3 dst-ip 10.0.0.9 src-port 2000 dst-port 2001 loc 33 + sudo ethtool -N <ethX> flow-type ip4 src-ip 10.0.0.6 dst-ip 10.0.0.4 loc 34 + + If you set action -1, then all traffic corresponding to the filter will be discarded. + + The maximum value action is 31. + + + The VLAN filter (VLAN id) is compared against 16 filters. + VLAN id must be accompanied by mask 0xF000. That is to distinguish VLAN filter + from L2 Ethertype filter with UserPriority since both User Priority and VLAN ID + are passed in the same 'vlan' parameter. + + To add a filter that directs packets from VLAN 2001 to queue 5:: + + ethtool -N <ethX> flow-type ip4 vlan 2001 m 0xF000 action 1 loc 0 + + + L2 EtherType filters allows filter packet by EtherType field or both EtherType + and User Priority (PCP) field of 802.1Q. + UserPriority (vlan) parameter must be accompanied by mask 0x1FFF. That is to + distinguish VLAN filter from L2 Ethertype filter with UserPriority since both + User Priority and VLAN ID are passed in the same 'vlan' parameter. + + To add a filter that directs IP4 packess of priority 3 to queue 3:: + + ethtool -N <ethX> flow-type ether proto 0x800 vlan 0x600 m 0x1FFF action 3 loc 16 + + To see the list of filters currently present:: + + ethtool <-u|-n|--show-nfc|--show-ntuple> <ethX> + + Rules may be deleted from the table itself. This is done using:: + + sudo ethtool <-N|-U|--config-nfc|--config-ntuple> <ethX> delete <loc> + + - loc is the rule number to be deleted. + + Rx filters is an interface to load the filter table that funnels all flow + into queue 0 unless an alternative queue is specified using "action". In that + case, any flow that matches the filter criteria will be directed to the + appropriate queue. RX filters is supported on all kernels 2.6.30 and later. + +RSS for UDP +----------- + + Currently, NIC does not support RSS for fragmented IP packets, which leads to + incorrect working of RSS for fragmented UDP traffic. To disable RSS for UDP the + RX Flow L3/L4 rule may be used. + + Example:: + + ethtool -N eth0 flow-type udp4 action 0 loc 32 + +UDP GSO hardware offload +------------------------ + + UDP GSO allows to boost UDP tx rates by offloading UDP headers allocation + into hardware. A special userspace socket option is required for this, + could be validated with /kernel/tools/testing/selftests/net/:: + + udpgso_bench_tx -u -4 -D 10.0.1.1 -s 6300 -S 100 + + Will cause sending out of 100 byte sized UDP packets formed from single + 6300 bytes user buffer. + + UDP GSO is configured by:: + + ethtool -K eth0 tx-udp-segmentation on + +Private flags (testing) +----------------------- + + Atlantic driver supports private flags for hardware custom features:: + + $ ethtool --show-priv-flags ethX + + Private flags for ethX: + DMASystemLoopback : off + PKTSystemLoopback : off + DMANetworkLoopback : off + PHYInternalLoopback: off + PHYExternalLoopback: off + + Example:: + + $ ethtool --set-priv-flags ethX DMASystemLoopback on + + DMASystemLoopback: DMA Host loopback. + PKTSystemLoopback: Packet buffer host loopback. + DMANetworkLoopback: Network side loopback on DMA block. + PHYInternalLoopback: Internal loopback on Phy. + PHYExternalLoopback: External loopback on Phy (with loopback ethernet cable). + + +Command Line Parameters +======================= +The following command line parameters are available on atlantic driver: + +aq_itr -Interrupt throttling mode +--------------------------------- +Accepted values: 0, 1, 0xFFFF + +Default value: 0xFFFF + +====== ============================================================== +0 Disable interrupt throttling. +1 Enable interrupt throttling and use specified tx and rx rates. +0xFFFF Auto throttling mode. Driver will choose the best RX and TX + interrupt throttling settings based on link speed. +====== ============================================================== + +aq_itr_tx - TX interrupt throttle rate +-------------------------------------- + +Accepted values: 0 - 0x1FF + +Default value: 0 + +TX side throttling in microseconds. Adapter will setup maximum interrupt delay +to this value. Minimum interrupt delay will be a half of this value + +aq_itr_rx - RX interrupt throttle rate +-------------------------------------- + +Accepted values: 0 - 0x1FF + +Default value: 0 + +RX side throttling in microseconds. Adapter will setup maximum interrupt delay +to this value. Minimum interrupt delay will be a half of this value + +.. note:: + + ITR settings could be changed in runtime by ethtool -c means (see below) + +Config file parameters +====================== + +For some fine tuning and performance optimizations, +some parameters can be changed in the {source_dir}/aq_cfg.h file. + +AQ_CFG_RX_PAGEORDER +------------------- + +Default value: 0 + +RX page order override. That's a power of 2 number of RX pages allocated for +each descriptor. Received descriptor size is still limited by +AQ_CFG_RX_FRAME_MAX. + +Increasing pageorder makes page reuse better (actual on iommu enabled systems). + +AQ_CFG_RX_REFILL_THRES +---------------------- + +Default value: 32 + +RX refill threshold. RX path will not refill freed descriptors until the +specified number of free descriptors is observed. Larger values may help +better page reuse but may lead to packet drops as well. + +AQ_CFG_VECS_DEF +--------------- + +Number of queues + +Valid Range: 0 - 8 (up to AQ_CFG_VECS_MAX) + +Default value: 8 + +Notice this value will be capped by the number of cores available on the system. + +AQ_CFG_IS_RSS_DEF +----------------- + +Enable/disable Receive Side Scaling + +This feature allows the adapter to distribute receive processing +across multiple CPU-cores and to prevent from overloading a single CPU core. + +Valid values + +== ======== +0 disabled +1 enabled +== ======== + +Default value: 1 + +AQ_CFG_NUM_RSS_QUEUES_DEF +------------------------- + +Number of queues for Receive Side Scaling + +Valid Range: 0 - 8 (up to AQ_CFG_VECS_DEF) + +Default value: AQ_CFG_VECS_DEF + +AQ_CFG_IS_LRO_DEF +----------------- + +Enable/disable Large Receive Offload + +This offload enables the adapter to coalesce multiple TCP segments and indicate +them as a single coalesced unit to the OS networking subsystem. + +The system consumes less energy but it also introduces more latency in packets +processing. + +Valid values + +== ======== +0 disabled +1 enabled +== ======== + +Default value: 1 + +AQ_CFG_TX_CLEAN_BUDGET +---------------------- + +Maximum descriptors to cleanup on TX at once. + +Default value: 256 + +After the aq_cfg.h file changed the driver must be rebuilt to take effect. + +Support +======= + +If an issue is identified with the released source code on the supported +kernel with a supported adapter, email the specific information related +to the issue to aqn_support@marvell.com + +License +======= + +aQuantia Corporation Network Driver + +Copyright |copy| 2014 - 2019 aQuantia Corporation. + +This program is free software; you can redistribute it and/or modify it +under the terms and conditions of the GNU General Public License, +version 2, as published by the Free Software Foundation. diff --git a/Documentation/networking/device_drivers/ethernet/chelsio/cxgb.rst b/Documentation/networking/device_drivers/ethernet/chelsio/cxgb.rst new file mode 100644 index 0000000000..435dce5fa2 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/chelsio/cxgb.rst @@ -0,0 +1,393 @@ +.. SPDX-License-Identifier: GPL-2.0 +.. include:: <isonum.txt> + +============================================= +Chelsio N210 10Gb Ethernet Network Controller +============================================= + +Driver Release Notes for Linux + +Version 2.1.1 + +June 20, 2005 + +.. Contents + + INTRODUCTION + FEATURES + PERFORMANCE + DRIVER MESSAGES + KNOWN ISSUES + SUPPORT + + +Introduction +============ + + This document describes the Linux driver for Chelsio 10Gb Ethernet Network + Controller. This driver supports the Chelsio N210 NIC and is backward + compatible with the Chelsio N110 model 10Gb NICs. + + +Features +======== + +Adaptive Interrupts (adaptive-rx) +--------------------------------- + + This feature provides an adaptive algorithm that adjusts the interrupt + coalescing parameters, allowing the driver to dynamically adapt the latency + settings to achieve the highest performance during various types of network + load. + + The interface used to control this feature is ethtool. Please see the + ethtool manpage for additional usage information. + + By default, adaptive-rx is disabled. + To enable adaptive-rx:: + + ethtool -C <interface> adaptive-rx on + + To disable adaptive-rx, use ethtool:: + + ethtool -C <interface> adaptive-rx off + + After disabling adaptive-rx, the timer latency value will be set to 50us. + You may set the timer latency after disabling adaptive-rx:: + + ethtool -C <interface> rx-usecs <microseconds> + + An example to set the timer latency value to 100us on eth0:: + + ethtool -C eth0 rx-usecs 100 + + You may also provide a timer latency value while disabling adaptive-rx:: + + ethtool -C <interface> adaptive-rx off rx-usecs <microseconds> + + If adaptive-rx is disabled and a timer latency value is specified, the timer + will be set to the specified value until changed by the user or until + adaptive-rx is enabled. + + To view the status of the adaptive-rx and timer latency values:: + + ethtool -c <interface> + + +TCP Segmentation Offloading (TSO) Support +----------------------------------------- + + This feature, also known as "large send", enables a system's protocol stack + to offload portions of outbound TCP processing to a network interface card + thereby reducing system CPU utilization and enhancing performance. + + The interface used to control this feature is ethtool version 1.8 or higher. + Please see the ethtool manpage for additional usage information. + + By default, TSO is enabled. + To disable TSO:: + + ethtool -K <interface> tso off + + To enable TSO:: + + ethtool -K <interface> tso on + + To view the status of TSO:: + + ethtool -k <interface> + + +Performance +=========== + + The following information is provided as an example of how to change system + parameters for "performance tuning" an what value to use. You may or may not + want to change these system parameters, depending on your server/workstation + application. Doing so is not warranted in any way by Chelsio Communications, + and is done at "YOUR OWN RISK". Chelsio will not be held responsible for loss + of data or damage to equipment. + + Your distribution may have a different way of doing things, or you may prefer + a different method. These commands are shown only to provide an example of + what to do and are by no means definitive. + + Making any of the following system changes will only last until you reboot + your system. You may want to write a script that runs at boot-up which + includes the optimal settings for your system. + + Setting PCI Latency Timer:: + + setpci -d 1425:: + +* 0x0c.l=0x0000F800 + + Disabling TCP timestamp:: + + sysctl -w net.ipv4.tcp_timestamps=0 + + Disabling SACK:: + + sysctl -w net.ipv4.tcp_sack=0 + + Setting large number of incoming connection requests:: + + sysctl -w net.ipv4.tcp_max_syn_backlog=3000 + + Setting maximum receive socket buffer size:: + + sysctl -w net.core.rmem_max=1024000 + + Setting maximum send socket buffer size:: + + sysctl -w net.core.wmem_max=1024000 + + Set smp_affinity (on a multiprocessor system) to a single CPU:: + + echo 1 > /proc/irq/<interrupt_number>/smp_affinity + + Setting default receive socket buffer size:: + + sysctl -w net.core.rmem_default=524287 + + Setting default send socket buffer size:: + + sysctl -w net.core.wmem_default=524287 + + Setting maximum option memory buffers:: + + sysctl -w net.core.optmem_max=524287 + + Setting maximum backlog (# of unprocessed packets before kernel drops):: + + sysctl -w net.core.netdev_max_backlog=300000 + + Setting TCP read buffers (min/default/max):: + + sysctl -w net.ipv4.tcp_rmem="10000000 10000000 10000000" + + Setting TCP write buffers (min/pressure/max):: + + sysctl -w net.ipv4.tcp_wmem="10000000 10000000 10000000" + + Setting TCP buffer space (min/pressure/max):: + + sysctl -w net.ipv4.tcp_mem="10000000 10000000 10000000" + + TCP window size for single connections: + + The receive buffer (RX_WINDOW) size must be at least as large as the + Bandwidth-Delay Product of the communication link between the sender and + receiver. Due to the variations of RTT, you may want to increase the buffer + size up to 2 times the Bandwidth-Delay Product. Reference page 289 of + "TCP/IP Illustrated, Volume 1, The Protocols" by W. Richard Stevens. + + At 10Gb speeds, use the following formula:: + + RX_WINDOW >= 1.25MBytes * RTT(in milliseconds) + Example for RTT with 100us: RX_WINDOW = (1,250,000 * 0.1) = 125,000 + + RX_WINDOW sizes of 256KB - 512KB should be sufficient. + + Setting the min, max, and default receive buffer (RX_WINDOW) size:: + + sysctl -w net.ipv4.tcp_rmem="<min> <default> <max>" + + TCP window size for multiple connections: + The receive buffer (RX_WINDOW) size may be calculated the same as single + connections, but should be divided by the number of connections. The + smaller window prevents congestion and facilitates better pacing, + especially if/when MAC level flow control does not work well or when it is + not supported on the machine. Experimentation may be necessary to attain + the correct value. This method is provided as a starting point for the + correct receive buffer size. + + Setting the min, max, and default receive buffer (RX_WINDOW) size is + performed in the same manner as single connection. + + +Driver Messages +=============== + + The following messages are the most common messages logged by syslog. These + may be found in /var/log/messages. + + Driver up:: + + Chelsio Network Driver - version 2.1.1 + + NIC detected:: + + eth#: Chelsio N210 1x10GBaseX NIC (rev #), PCIX 133MHz/64-bit + + Link up:: + + eth#: link is up at 10 Gbps, full duplex + + Link down:: + + eth#: link is down + + +Known Issues +============ + + These issues have been identified during testing. The following information + is provided as a workaround to the problem. In some cases, this problem is + inherent to Linux or to a particular Linux Distribution and/or hardware + platform. + + 1. Large number of TCP retransmits on a multiprocessor (SMP) system. + + On a system with multiple CPUs, the interrupt (IRQ) for the network + controller may be bound to more than one CPU. This will cause TCP + retransmits if the packet data were to be split across different CPUs + and re-assembled in a different order than expected. + + To eliminate the TCP retransmits, set smp_affinity on the particular + interrupt to a single CPU. You can locate the interrupt (IRQ) used on + the N110/N210 by using ifconfig:: + + ifconfig <dev_name> | grep Interrupt + + Set the smp_affinity to a single CPU:: + + echo 1 > /proc/irq/<interrupt_number>/smp_affinity + + It is highly suggested that you do not run the irqbalance daemon on your + system, as this will change any smp_affinity setting you have applied. + The irqbalance daemon runs on a 10 second interval and binds interrupts + to the least loaded CPU determined by the daemon. To disable this daemon:: + + chkconfig --level 2345 irqbalance off + + By default, some Linux distributions enable the kernel feature, + irqbalance, which performs the same function as the daemon. To disable + this feature, add the following line to your bootloader:: + + noirqbalance + + Example using the Grub bootloader:: + + title Red Hat Enterprise Linux AS (2.4.21-27.ELsmp) + root (hd0,0) + kernel /vmlinuz-2.4.21-27.ELsmp ro root=/dev/hda3 noirqbalance + initrd /initrd-2.4.21-27.ELsmp.img + + 2. After running insmod, the driver is loaded and the incorrect network + interface is brought up without running ifup. + + When using 2.4.x kernels, including RHEL kernels, the Linux kernel + invokes a script named "hotplug". This script is primarily used to + automatically bring up USB devices when they are plugged in, however, + the script also attempts to automatically bring up a network interface + after loading the kernel module. The hotplug script does this by scanning + the ifcfg-eth# config files in /etc/sysconfig/network-scripts, looking + for HWADDR=<mac_address>. + + If the hotplug script does not find the HWADDRR within any of the + ifcfg-eth# files, it will bring up the device with the next available + interface name. If this interface is already configured for a different + network card, your new interface will have incorrect IP address and + network settings. + + To solve this issue, you can add the HWADDR=<mac_address> key to the + interface config file of your network controller. + + To disable this "hotplug" feature, you may add the driver (module name) + to the "blacklist" file located in /etc/hotplug. It has been noted that + this does not work for network devices because the net.agent script + does not use the blacklist file. Simply remove, or rename, the net.agent + script located in /etc/hotplug to disable this feature. + + 3. Transport Protocol (TP) hangs when running heavy multi-connection traffic + on an AMD Opteron system with HyperTransport PCI-X Tunnel chipset. + + If your AMD Opteron system uses the AMD-8131 HyperTransport PCI-X Tunnel + chipset, you may experience the "133-Mhz Mode Split Completion Data + Corruption" bug identified by AMD while using a 133Mhz PCI-X card on the + bus PCI-X bus. + + AMD states, "Under highly specific conditions, the AMD-8131 PCI-X Tunnel + can provide stale data via split completion cycles to a PCI-X card that + is operating at 133 Mhz", causing data corruption. + + AMD's provides three workarounds for this problem, however, Chelsio + recommends the first option for best performance with this bug: + + For 133Mhz secondary bus operation, limit the transaction length and + the number of outstanding transactions, via BIOS configuration + programming of the PCI-X card, to the following: + + Data Length (bytes): 1k + + Total allowed outstanding transactions: 2 + + Please refer to AMD 8131-HT/PCI-X Errata 26310 Rev 3.08 August 2004, + section 56, "133-MHz Mode Split Completion Data Corruption" for more + details with this bug and workarounds suggested by AMD. + + It may be possible to work outside AMD's recommended PCI-X settings, try + increasing the Data Length to 2k bytes for increased performance. If you + have issues with these settings, please revert to the "safe" settings + and duplicate the problem before submitting a bug or asking for support. + + .. note:: + + The default setting on most systems is 8 outstanding transactions + and 2k bytes data length. + + 4. On multiprocessor systems, it has been noted that an application which + is handling 10Gb networking can switch between CPUs causing degraded + and/or unstable performance. + + If running on an SMP system and taking performance measurements, it + is suggested you either run the latest netperf-2.4.0+ or use a binding + tool such as Tim Hockin's procstate utilities (runon) + <http://www.hockin.org/~thockin/procstate/>. + + Binding netserver and netperf (or other applications) to particular + CPUs will have a significant difference in performance measurements. + You may need to experiment which CPU to bind the application to in + order to achieve the best performance for your system. + + If you are developing an application designed for 10Gb networking, + please keep in mind you may want to look at kernel functions + sched_setaffinity & sched_getaffinity to bind your application. + + If you are just running user-space applications such as ftp, telnet, + etc., you may want to try the runon tool provided by Tim Hockin's + procstate utility. You could also try binding the interface to a + particular CPU: runon 0 ifup eth0 + + +Support +======= + + If you have problems with the software or hardware, please contact our + customer support team via email at support@chelsio.com or check our website + at http://www.chelsio.com + +------------------------------------------------------------------------------- + +:: + + Chelsio Communications + 370 San Aleso Ave. + Suite 100 + Sunnyvale, CA 94085 + http://www.chelsio.com + +This program is free software; you can redistribute it and/or modify +it under the terms of the GNU General Public License, version 2, as +published by the Free Software Foundation. + +You should have received a copy of the GNU General Public License along +with this program; if not, write to the Free Software Foundation, Inc., +59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + +THIS SOFTWARE IS PROVIDED ``AS IS`` AND WITHOUT ANY EXPRESS OR IMPLIED +WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF +MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. + +Copyright |copy| 2003-2005 Chelsio Communications. All rights reserved. diff --git a/Documentation/networking/device_drivers/ethernet/cirrus/cs89x0.rst b/Documentation/networking/device_drivers/ethernet/cirrus/cs89x0.rst new file mode 100644 index 0000000000..e5c283940a --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/cirrus/cs89x0.rst @@ -0,0 +1,647 @@ +.. SPDX-License-Identifier: GPL-2.0 + +================================================ +Cirrus Logic LAN CS8900/CS8920 Ethernet Adapters +================================================ + +.. note:: + + This document was contributed by Cirrus Logic for kernel 2.2.5. This version + has been updated for 2.3.48 by Andrew Morton. + + Still, this is too outdated! A major cleanup is needed here. + +Cirrus make a copy of this driver available at their website, as +described below. In general, you should use the driver version which +comes with your Linux distribution. + + +Linux Network Interface Driver ver. 2.00 <kernel 2.3.48> + + +.. TABLE OF CONTENTS + + 1.0 CIRRUS LOGIC LAN CS8900/CS8920 ETHERNET ADAPTERS + 1.1 Product Overview + 1.2 Driver Description + 1.2.1 Driver Name + 1.2.2 File in the Driver Package + 1.3 System Requirements + 1.4 Licensing Information + + 2.0 ADAPTER INSTALLATION and CONFIGURATION + 2.1 CS8900-based Adapter Configuration + 2.2 CS8920-based Adapter Configuration + + 3.0 LOADING THE DRIVER AS A MODULE + + 4.0 COMPILING THE DRIVER + 4.1 Compiling the Driver as a Loadable Module + 4.2 Compiling the driver to support memory mode + 4.3 Compiling the driver to support Rx DMA + + 5.0 TESTING AND TROUBLESHOOTING + 5.1 Known Defects and Limitations + 5.2 Testing the Adapter + 5.2.1 Diagnostic Self-Test + 5.2.2 Diagnostic Network Test + 5.3 Using the Adapter's LEDs + 5.4 Resolving I/O Conflicts + + 6.0 TECHNICAL SUPPORT + 6.1 Contacting Cirrus Logic's Technical Support + 6.2 Information Required Before Contacting Technical Support + 6.3 Obtaining the Latest Driver Version + 6.4 Current maintainer + 6.5 Kernel boot parameters + + +1. Cirrus Logic LAN CS8900/CS8920 Ethernet Adapters +=================================================== + + +1.1. Product Overview +===================== + +The CS8900-based ISA Ethernet Adapters from Cirrus Logic follow +IEEE 802.3 standards and support half or full-duplex operation in ISA bus +computers on 10 Mbps Ethernet networks. The adapters are designed for operation +in 16-bit ISA or EISA bus expansion slots and are available in +10BaseT-only or 3-media configurations (10BaseT, 10Base2, and AUI for 10Base-5 +or fiber networks). + +CS8920-based adapters are similar to the CS8900-based adapter with additional +features for Plug and Play (PnP) support and Wakeup Frame recognition. As +such, the configuration procedures differ somewhat between the two types of +adapters. Refer to the "Adapter Configuration" section for details on +configuring both types of adapters. + + +1.2. Driver Description +======================= + +The CS8900/CS8920 Ethernet Adapter driver for Linux supports the Linux +v2.3.48 or greater kernel. It can be compiled directly into the kernel +or loaded at run-time as a device driver module. + +1.2.1 Driver Name: cs89x0 + +1.2.2 Files in the Driver Archive: + +The files in the driver at Cirrus' website include: + + =================== ==================================================== + readme.txt this file + build batch file to compile cs89x0.c. + cs89x0.c driver C code + cs89x0.h driver header file + cs89x0.o pre-compiled module (for v2.2.5 kernel) + config/Config.in sample file to include cs89x0 driver in the kernel. + config/Makefile sample file to include cs89x0 driver in the kernel. + config/Space.c sample file to include cs89x0 driver in the kernel. + =================== ==================================================== + + + +1.3. System Requirements +------------------------ + +The following hardware is required: + + * Cirrus Logic LAN (CS8900/20-based) Ethernet ISA Adapter + + * IBM or IBM-compatible PC with: + * An 80386 or higher processor + * 16 bytes of contiguous IO space available between 210h - 370h + * One available IRQ (5,10,11,or 12 for the CS8900, 3-7,9-15 for CS8920). + + * Appropriate cable (and connector for AUI, 10BASE-2) for your network + topology. + +The following software is required: + +* LINUX kernel version 2.3.48 or higher + + * CS8900/20 Setup Utility (DOS-based) + + * LINUX kernel sources for your kernel (if compiling into kernel) + + * GNU Toolkit (gcc and make) v2.6 or above (if compiling into kernel + or a module) + + + +1.4. Licensing Information +-------------------------- + +This program is free software; you can redistribute it and/or modify it under +the terms of the GNU General Public License as published by the Free Software +Foundation, version 1. + +This program is distributed in the hope that it will be useful, but WITHOUT +ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or +FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for +more details. + +For a full copy of the GNU General Public License, write to the Free Software +Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + + + +2. Adapter Installation and Configuration +========================================= + +Both the CS8900 and CS8920-based adapters can be configured using parameters +stored in an on-board EEPROM. You must use the DOS-based CS8900/20 Setup +Utility if you want to change the adapter's configuration in EEPROM. + +When loading the driver as a module, you can specify many of the adapter's +configuration parameters on the command-line to override the EEPROM's settings +or for interface configuration when an EEPROM is not used. (CS8920-based +adapters must use an EEPROM.) See Section 3.0 LOADING THE DRIVER AS A MODULE. + +Since the CS8900/20 Setup Utility is a DOS-based application, you must install +and configure the adapter in a DOS-based system using the CS8900/20 Setup +Utility before installation in the target LINUX system. (Not required if +installing a CS8900-based adapter and the default configuration is acceptable.) + + +2.1. CS8900-based Adapter Configuration +--------------------------------------- + +CS8900-based adapters shipped from Cirrus Logic have been configured +with the following "default" settings:: + + Operation Mode: Memory Mode + IRQ: 10 + Base I/O Address: 300 + Memory Base Address: D0000 + Optimization: DOS Client + Transmission Mode: Half-duplex + BootProm: None + Media Type: Autodetect (3-media cards) or + 10BASE-T (10BASE-T only adapter) + +You should only change the default configuration settings if conflicts with +another adapter exists. To change the adapter's configuration, run the +CS8900/20 Setup Utility. + + +2.2. CS8920-based Adapter Configuration +--------------------------------------- + +CS8920-based adapters are shipped from Cirrus Logic configured as Plug +and Play (PnP) enabled. However, since the cs89x0 driver does NOT +support PnP, you must install the CS8920 adapter in a DOS-based PC and +run the CS8900/20 Setup Utility to disable PnP and configure the +adapter before installation in the target Linux system. Failure to do +this will leave the adapter inactive and the driver will be unable to +communicate with the adapter. + +:: + + **************************************************************** + * CS8920-BASED ADAPTERS: * + * * + * CS8920-BASED ADAPTERS ARE PLUG and PLAY ENABLED BY DEFAULT. * + * THE CS89X0 DRIVER DOES NOT SUPPORT PnP. THEREFORE, YOU MUST * + * RUN THE CS8900/20 SETUP UTILITY TO DISABLE PnP SUPPORT AND * + * TO ACTIVATE THE ADAPTER. * + **************************************************************** + + + + +3. Loading the Driver as a Module +================================= + +If the driver is compiled as a loadable module, you can load the driver module +with the 'modprobe' command. Many of the adapter's configuration parameters can +be specified as command-line arguments to the load command. This facility +provides a means to override the EEPROM's settings or for interface +configuration when an EEPROM is not used. + +Example:: + + insmod cs89x0.o io=0x200 irq=0xA media=aui + +This example loads the module and configures the adapter to use an IO port base +address of 200h, interrupt 10, and use the AUI media connection. The following +configuration options are available on the command line:: + + io=### - specify IO address (200h-360h) + irq=## - specify interrupt level + use_dma=1 - Enable DMA + dma=# - specify dma channel (Driver is compiled to support + Rx DMA only) + dmasize=# (16 or 64) - DMA size 16K or 64K. Default value is set to 16. + media=rj45 - specify media type + or media=bnc + or media=aui + or media=auto + duplex=full - specify forced half/full/autonegotiate duplex + or duplex=half + or duplex=auto + debug=# - debug level (only available if the driver was compiled + for debugging) + +**Notes:** + +a) If an EEPROM is present, any specified command-line parameter + will override the corresponding configuration value stored in + EEPROM. + +b) The "io" parameter must be specified on the command-line. + +c) The driver's hardware probe routine is designed to avoid + writing to I/O space until it knows that there is a cs89x0 + card at the written addresses. This could cause problems + with device probing. To avoid this behaviour, add one + to the ``io=`` module parameter. This doesn't actually change + the I/O address, but it is a flag to tell the driver + to partially initialise the hardware before trying to + identify the card. This could be dangerous if you are + not sure that there is a cs89x0 card at the provided address. + + For example, to scan for an adapter located at IO base 0x300, + specify an IO address of 0x301. + +d) The "duplex=auto" parameter is only supported for the CS8920. + +e) The minimum command-line configuration required if an EEPROM is + not present is: + + io + irq + media type (no autodetect) + +f) The following additional parameters are CS89XX defaults (values + used with no EEPROM or command-line argument). + + * DMA Burst = enabled + * IOCHRDY Enabled = enabled + * UseSA = enabled + * CS8900 defaults to half-duplex if not specified on command-line + * CS8920 defaults to autoneg if not specified on command-line + * Use reset defaults for other config parameters + * dma_mode = 0 + +g) You can use ifconfig to set the adapter's Ethernet address. + +h) Many Linux distributions use the 'modprobe' command to load + modules. This program uses the '/etc/conf.modules' file to + determine configuration information which is passed to a driver + module when it is loaded. All the configuration options which are + described above may be placed within /etc/conf.modules. + + For example:: + + > cat /etc/conf.modules + ... + alias eth0 cs89x0 + options cs89x0 io=0x0200 dma=5 use_dma=1 + ... + + In this example we are telling the module system that the + ethernet driver for this machine should use the cs89x0 driver. We + are asking 'modprobe' to pass the 'io', 'dma' and 'use_dma' + arguments to the driver when it is loaded. + +i) Cirrus recommend that the cs89x0 use the ISA DMA channels 5, 6 or + 7. You will probably find that other DMA channels will not work. + +j) The cs89x0 supports DMA for receiving only. DMA mode is + significantly more efficient. Flooding a 400 MHz Celeron machine + with large ping packets consumes 82% of its CPU capacity in non-DMA + mode. With DMA this is reduced to 45%. + +k) If your Linux kernel was compiled with inbuilt plug-and-play + support you will be able to find information about the cs89x0 card + with the command:: + + cat /proc/isapnp + +l) If during DMA operation you find erratic behavior or network data + corruption you should use your PC's BIOS to slow the EISA bus clock. + +m) If the cs89x0 driver is compiled directly into the kernel + (non-modular) then its I/O address is automatically determined by + ISA bus probing. The IRQ number, media options, etc are determined + from the card's EEPROM. + +n) If the cs89x0 driver is compiled directly into the kernel, DMA + mode may be selected by providing the kernel with a boot option + 'cs89x0_dma=N' where 'N' is the desired DMA channel number (5, 6 or 7). + + Kernel boot options may be provided on the LILO command line:: + + LILO boot: linux cs89x0_dma=5 + + or they may be placed in /etc/lilo.conf:: + + image=/boot/bzImage-2.3.48 + append="cs89x0_dma=5" + label=linux + root=/dev/hda5 + read-only + + The DMA Rx buffer size is hardwired to 16 kbytes in this mode. + (64k mode is not available). + + +4. Compiling the Driver +======================= + +The cs89x0 driver can be compiled directly into the kernel or compiled into +a loadable device driver module. + +Just use the standard way to configure the driver and compile the Kernel. + + +4.1. Compiling the Driver to Support Rx DMA +------------------------------------------- + +The compile-time optionality for DMA was removed in the 2.3 kernel +series. DMA support is now unconditionally part of the driver. It is +enabled by the 'use_dma=1' module option. + + +5. Testing and Troubleshooting +============================== + +5.1. Known Defects and Limitations +---------------------------------- + +Refer to the RELEASE.TXT file distributed as part of this archive for a list of +known defects, driver limitations, and work arounds. + + +5.2. Testing the Adapter +------------------------ + +Once the adapter has been installed and configured, the diagnostic option of +the CS8900/20 Setup Utility can be used to test the functionality of the +adapter and its network connection. Use the diagnostics 'Self Test' option to +test the functionality of the adapter with the hardware configuration you have +assigned. You can use the diagnostics 'Network Test' to test the ability of the +adapter to communicate across the Ethernet with another PC equipped with a +CS8900/20-based adapter card (it must also be running the CS8900/20 Setup +Utility). + +.. note:: + + The Setup Utility's diagnostics are designed to run in a + DOS-only operating system environment. DO NOT run the diagnostics + from a DOS or command prompt session under Windows 95, Windows NT, + OS/2, or other operating system. + +To run the diagnostics tests on the CS8900/20 adapter: + + 1. Boot DOS on the PC and start the CS8900/20 Setup Utility. + + 2. The adapter's current configuration is displayed. Hit the ENTER key to + get to the main menu. + + 4. Select 'Diagnostics' (ALT-G) from the main menu. + * Select 'Self-Test' to test the adapter's basic functionality. + * Select 'Network Test' to test the network connection and cabling. + + +5.2.1. Diagnostic Self-test +^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +The diagnostic self-test checks the adapter's basic functionality as well as +its ability to communicate across the ISA bus based on the system resources +assigned during hardware configuration. The following tests are performed: + + * IO Register Read/Write Test + + The IO Register Read/Write test insures that the CS8900/20 can be + accessed in IO mode, and that the IO base address is correct. + + * Shared Memory Test + + The Shared Memory test insures the CS8900/20 can be accessed in memory + mode and that the range of memory addresses assigned does not conflict + with other devices in the system. + + * Interrupt Test + + The Interrupt test insures there are no conflicts with the assigned IRQ + signal. + + * EEPROM Test + + The EEPROM test insures the EEPROM can be read. + + * Chip RAM Test + + The Chip RAM test insures the 4K of memory internal to the CS8900/20 is + working properly. + + * Internal Loop-back Test + + The Internal Loop Back test insures the adapter's transmitter and + receiver are operating properly. If this test fails, make sure the + adapter's cable is connected to the network (check for LED activity for + example). + + * Boot PROM Test + + The Boot PROM test insures the Boot PROM is present, and can be read. + Failure indicates the Boot PROM was not successfully read due to a + hardware problem or due to a conflicts on the Boot PROM address + assignment. (Test only applies if the adapter is configured to use the + Boot PROM option.) + +Failure of a test item indicates a possible system resource conflict with +another device on the ISA bus. In this case, you should use the Manual Setup +option to reconfigure the adapter by selecting a different value for the system +resource that failed. + + +5.2.2. Diagnostic Network Test +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +The Diagnostic Network Test verifies a working network connection by +transferring data between two CS8900/20 adapters installed in different PCs +on the same network. (Note: the diagnostic network test should not be run +between two nodes across a router.) + +This test requires that each of the two PCs have a CS8900/20-based adapter +installed and have the CS8900/20 Setup Utility running. The first PC is +configured as a Responder and the other PC is configured as an Initiator. +Once the Initiator is started, it sends data frames to the Responder which +returns the frames to the Initiator. + +The total number of frames received and transmitted are displayed on the +Initiator's display, along with a count of the number of frames received and +transmitted OK or in error. The test can be terminated anytime by the user at +either PC. + +To setup the Diagnostic Network Test: + + 1. Select a PC with a CS8900/20-based adapter and a known working network + connection to act as the Responder. Run the CS8900/20 Setup Utility + and select 'Diagnostics -> Network Test -> Responder' from the main + menu. Hit ENTER to start the Responder. + + 2. Return to the PC with the CS8900/20-based adapter you want to test and + start the CS8900/20 Setup Utility. + + 3. From the main menu, Select 'Diagnostic -> Network Test -> Initiator'. + Hit ENTER to start the test. + +You may stop the test on the Initiator at any time while allowing the Responder +to continue running. In this manner, you can move to additional PCs and test +them by starting the Initiator on another PC without having to stop/start the +Responder. + + + +5.3. Using the Adapter's LEDs +----------------------------- + +The 2 and 3-media adapters have two LEDs visible on the back end of the board +located near the 10Base-T connector. + +Link Integrity LED: A "steady" ON of the green LED indicates a valid 10Base-T +connection. (Only applies to 10Base-T. The green LED has no significance for +a 10Base-2 or AUI connection.) + +TX/RX LED: The yellow LED lights briefly each time the adapter transmits or +receives data. (The yellow LED will appear to "flicker" on a typical network.) + + +5.4. Resolving I/O Conflicts +---------------------------- + +An IO conflict occurs when two or more adapter use the same ISA resource (IO +address, memory address or IRQ). You can usually detect an IO conflict in one +of four ways after installing and or configuring the CS8900/20-based adapter: + + 1. The system does not boot properly (or at all). + + 2. The driver cannot communicate with the adapter, reporting an "Adapter + not found" error message. + + 3. You cannot connect to the network or the driver will not load. + + 4. If you have configured the adapter to run in memory mode but the driver + reports it is using IO mode when loading, this is an indication of a + memory address conflict. + +If an IO conflict occurs, run the CS8900/20 Setup Utility and perform a +diagnostic self-test. Normally, the ISA resource in conflict will fail the +self-test. If so, reconfigure the adapter selecting another choice for the +resource in conflict. Run the diagnostics again to check for further IO +conflicts. + +In some cases, such as when the PC will not boot, it may be necessary to remove +the adapter and reconfigure it by installing it in another PC to run the +CS8900/20 Setup Utility. Once reinstalled in the target system, run the +diagnostics self-test to ensure the new configuration is free of conflicts +before loading the driver again. + +When manually configuring the adapter, keep in mind the typical ISA system +resource usage as indicated in the tables below. + +:: + + I/O Address Device IRQ Device + ----------- -------- --- -------- + 200-20F Game I/O adapter 3 COM2, Bus Mouse + 230-23F Bus Mouse 4 COM1 + 270-27F LPT3: third parallel port 5 LPT2 + 2F0-2FF COM2: second serial port 6 Floppy Disk controller + 320-32F Fixed disk controller 7 LPT1 + 8 Real-time Clock + 9 EGA/VGA display adapter + 12 Mouse (PS/2) + Memory Address Device 13 Math Coprocessor + -------------- --------------------- 14 Hard Disk controller + A000-BFFF EGA Graphics Adapter + A000-C7FF VGA Graphics Adapter + B000-BFFF Mono Graphics Adapter + B800-BFFF Color Graphics Adapter + E000-FFFF AT BIOS + + + + +6. Technical Support +==================== + +6.1. Contacting Cirrus Logic's Technical Support +------------------------------------------------ + +Cirrus Logic's CS89XX Technical Application Support can be reached at:: + + Telephone :(800) 888-5016 (from inside U.S. and Canada) + :(512) 442-7555 (from outside the U.S. and Canada) + Fax :(512) 912-3871 + Email :ethernet@crystal.cirrus.com + WWW :http://www.cirrus.com + + +6.2. Information Required before Contacting Technical Support +------------------------------------------------------------- + +Before contacting Cirrus Logic for technical support, be prepared to provide as +Much of the following information as possible. + +1.) Adapter type (CRD8900, CDB8900, CDB8920, etc.) + +2.) Adapter configuration + + * IO Base, Memory Base, IO or memory mode enabled, IRQ, DMA channel + * Plug and Play enabled/disabled (CS8920-based adapters only) + * Configured for media auto-detect or specific media type (which type). + +3.) PC System's Configuration + + * Plug and Play system (yes/no) + * BIOS (make and version) + * System make and model + * CPU (type and speed) + * System RAM + * SCSI Adapter + +4.) Software + + * CS89XX driver and version + * Your network operating system and version + * Your system's OS version + * Version of all protocol support files + +5.) Any Error Message displayed. + + + +6.3 Obtaining the Latest Driver Version +--------------------------------------- + +You can obtain the latest CS89XX drivers and support software from Cirrus Logic's +Web site. You can also contact Cirrus Logic's Technical Support (email: +ethernet@crystal.cirrus.com) and request that you be registered for automatic +software-update notification. + +Cirrus Logic maintains a web page at http://www.cirrus.com with the +latest drivers and technical publications. + + +6.4. Current maintainer +----------------------- + +In February 2000 the maintenance of this driver was assumed by Andrew +Morton. + +6.5 Kernel module parameters +---------------------------- + +For use in embedded environments with no cs89x0 EEPROM, the kernel boot +parameter ``cs89x0_media=`` has been implemented. Usage is:: + + cs89x0_media=rj45 or + cs89x0_media=aui or + cs89x0_media=bnc diff --git a/Documentation/networking/device_drivers/ethernet/davicom/dm9000.rst b/Documentation/networking/device_drivers/ethernet/davicom/dm9000.rst new file mode 100644 index 0000000000..14eb0a4d4e --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/davicom/dm9000.rst @@ -0,0 +1,171 @@ +.. SPDX-License-Identifier: GPL-2.0 + +===================== +DM9000 Network driver +===================== + +Copyright 2008 Simtec Electronics, + + Ben Dooks <ben@simtec.co.uk> <ben-linux@fluff.org> + + +Introduction +------------ + +This file describes how to use the DM9000 platform-device based network driver +that is contained in the files drivers/net/dm9000.c and drivers/net/dm9000.h. + +The driver supports three DM9000 variants, the DM9000E which is the first chip +supported as well as the newer DM9000A and DM9000B devices. It is currently +maintained and tested by Ben Dooks, who should be CC: to any patches for this +driver. + + +Defining the platform device +---------------------------- + +The minimum set of resources attached to the platform device are as follows: + + 1) The physical address of the address register + 2) The physical address of the data register + 3) The IRQ line the device's interrupt pin is connected to. + +These resources should be specified in that order, as the ordering of the +two address regions is important (the driver expects these to be address +and then data). + +An example from arch/arm/mach-s3c/mach-bast.c is:: + + static struct resource bast_dm9k_resource[] = { + [0] = { + .start = S3C2410_CS5 + BAST_PA_DM9000, + .end = S3C2410_CS5 + BAST_PA_DM9000 + 3, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = S3C2410_CS5 + BAST_PA_DM9000 + 0x40, + .end = S3C2410_CS5 + BAST_PA_DM9000 + 0x40 + 0x3f, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = IRQ_DM9000, + .end = IRQ_DM9000, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + } + }; + + static struct platform_device bast_device_dm9k = { + .name = "dm9000", + .id = 0, + .num_resources = ARRAY_SIZE(bast_dm9k_resource), + .resource = bast_dm9k_resource, + }; + +Note the setting of the IRQ trigger flag in bast_dm9k_resource[2].flags, +as this will generate a warning if it is not present. The trigger from +the flags field will be passed to request_irq() when registering the IRQ +handler to ensure that the IRQ is setup correctly. + +This shows a typical platform device, without the optional configuration +platform data supplied. The next example uses the same resources, but adds +the optional platform data to pass extra configuration data:: + + static struct dm9000_plat_data bast_dm9k_platdata = { + .flags = DM9000_PLATF_16BITONLY, + }; + + static struct platform_device bast_device_dm9k = { + .name = "dm9000", + .id = 0, + .num_resources = ARRAY_SIZE(bast_dm9k_resource), + .resource = bast_dm9k_resource, + .dev = { + .platform_data = &bast_dm9k_platdata, + } + }; + +The platform data is defined in include/linux/dm9000.h and described below. + + +Platform data +------------- + +Extra platform data for the DM9000 can describe the IO bus width to the +device, whether or not an external PHY is attached to the device and +the availability of an external configuration EEPROM. + +The flags for the platform data .flags field are as follows: + +DM9000_PLATF_8BITONLY + + The IO should be done with 8bit operations. + +DM9000_PLATF_16BITONLY + + The IO should be done with 16bit operations. + +DM9000_PLATF_32BITONLY + + The IO should be done with 32bit operations. + +DM9000_PLATF_EXT_PHY + + The chip is connected to an external PHY. + +DM9000_PLATF_NO_EEPROM + + This can be used to signify that the board does not have an + EEPROM, or that the EEPROM should be hidden from the user. + +DM9000_PLATF_SIMPLE_PHY + + Switch to using the simpler PHY polling method which does not + try and read the MII PHY state regularly. This is only available + when using the internal PHY. See the section on link state polling + for more information. + + The config symbol DM9000_FORCE_SIMPLE_PHY_POLL, Kconfig entry + "Force simple NSR based PHY polling" allows this flag to be + forced on at build time. + + +PHY Link state polling +---------------------- + +The driver keeps track of the link state and informs the network core +about link (carrier) availability. This is managed by several methods +depending on the version of the chip and on which PHY is being used. + +For the internal PHY, the original (and currently default) method is +to read the MII state, either when the status changes if we have the +necessary interrupt support in the chip or every two seconds via a +periodic timer. + +To reduce the overhead for the internal PHY, there is now the option +of using the DM9000_FORCE_SIMPLE_PHY_POLL config, or DM9000_PLATF_SIMPLE_PHY +platform data option to read the summary information without the +expensive MII accesses. This method is faster, but does not print +as much information. + +When using an external PHY, the driver currently has to poll the MII +link status as there is no method for getting an interrupt on link change. + + +DM9000A / DM9000B +----------------- + +These chips are functionally similar to the DM9000E and are supported easily +by the same driver. The features are: + + 1) Interrupt on internal PHY state change. This means that the periodic + polling of the PHY status may be disabled on these devices when using + the internal PHY. + + 2) TCP/UDP checksum offloading, which the driver does not currently support. + + +ethtool +------- + +The driver supports the ethtool interface for access to the driver +state information, the PHY state and the EEPROM. diff --git a/Documentation/networking/device_drivers/ethernet/dec/dmfe.rst b/Documentation/networking/device_drivers/ethernet/dec/dmfe.rst new file mode 100644 index 0000000000..c4cf809cad --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/dec/dmfe.rst @@ -0,0 +1,71 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============================================================== +Davicom DM9102(A)/DM9132/DM9801 fast ethernet driver for Linux +============================================================== + +Note: This driver doesn't have a maintainer. + + +This program is free software; you can redistribute it and/or +modify it under the terms of the GNU General Public License +as published by the Free Software Foundation; either version 2 +of the License, or (at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + + +This driver provides kernel support for Davicom DM9102(A)/DM9132/DM9801 ethernet cards ( CNET +10/100 ethernet cards uses Davicom chipset too, so this driver supports CNET cards too ).If you +didn't compile this driver as a module, it will automatically load itself on boot and print a +line similar to:: + + dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17) + +If you compiled this driver as a module, you have to load it on boot.You can load it with command:: + + insmod dmfe + +This way it will autodetect the device mode.This is the suggested way to load the module.Or you can pass +a mode= setting to module while loading, like:: + + insmod dmfe mode=0 # Force 10M Half Duplex + insmod dmfe mode=1 # Force 100M Half Duplex + insmod dmfe mode=4 # Force 10M Full Duplex + insmod dmfe mode=5 # Force 100M Full Duplex + +Next you should configure your network interface with a command similar to:: + + ifconfig eth0 172.22.3.18 + ^^^^^^^^^^^ + Your IP Address + +Then you may have to modify the default routing table with command:: + + route add default eth0 + + +Now your ethernet card should be up and running. + + +TODO: + +- Implement pci_driver::suspend() and pci_driver::resume() power management methods. +- Check on 64 bit boxes. +- Check and fix on big endian boxes. +- Test and make sure PCI latency is now correct for all cases. + + +Authors: + +Sten Wang <sten_wang@davicom.com.tw > : Original Author + +Contributors: + +- Marcelo Tosatti <marcelo@conectiva.com.br> +- Alan Cox <alan@lxorguk.ukuu.org.uk> +- Jeff Garzik <jgarzik@pobox.com> +- Vojtech Pavlik <vojtech@suse.cz> diff --git a/Documentation/networking/device_drivers/ethernet/dlink/dl2k.rst b/Documentation/networking/device_drivers/ethernet/dlink/dl2k.rst new file mode 100644 index 0000000000..ccdb5d0d74 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/dlink/dl2k.rst @@ -0,0 +1,314 @@ +.. SPDX-License-Identifier: GPL-2.0 + +========================================================= +D-Link DL2000-based Gigabit Ethernet Adapter Installation +========================================================= + +May 23, 2002 + +.. Contents + + - Compatibility List + - Quick Install + - Compiling the Driver + - Installing the Driver + - Option parameter + - Configuration Script Sample + - Troubleshooting + + +Compatibility List +================== + +Adapter Support: + +- D-Link DGE-550T Gigabit Ethernet Adapter. +- D-Link DGE-550SX Gigabit Ethernet Adapter. +- D-Link DL2000-based Gigabit Ethernet Adapter. + + +The driver support Linux kernel 2.4.7 later. We had tested it +on the environments below. + + . Red Hat v6.2 (update kernel to 2.4.7) + . Red Hat v7.0 (update kernel to 2.4.7) + . Red Hat v7.1 (kernel 2.4.7) + . Red Hat v7.2 (kernel 2.4.7-10) + + +Quick Install +============= +Install linux driver as following command:: + + 1. make all + 2. insmod dl2k.ko + 3. ifconfig eth0 up 10.xxx.xxx.xxx netmask 255.0.0.0 + ^^^^^^^^^^^^^^^\ ^^^^^^^^\ + IP NETMASK + +Now eth0 should active, you can test it by "ping" or get more information by +"ifconfig". If tested ok, continue the next step. + +4. ``cp dl2k.ko /lib/modules/`uname -r`/kernel/drivers/net`` +5. Add the following line to /etc/modprobe.d/dl2k.conf:: + + alias eth0 dl2k + +6. Run ``depmod`` to updated module indexes. +7. Run ``netconfig`` or ``netconf`` to create configuration script ifcfg-eth0 + located at /etc/sysconfig/network-scripts or create it manually. + + [see - Configuration Script Sample] +8. Driver will automatically load and configure at next boot time. + +Compiling the Driver +==================== +In Linux, NIC drivers are most commonly configured as loadable modules. +The approach of building a monolithic kernel has become obsolete. The driver +can be compiled as part of a monolithic kernel, but is strongly discouraged. +The remainder of this section assumes the driver is built as a loadable module. +In the Linux environment, it is a good idea to rebuild the driver from the +source instead of relying on a precompiled version. This approach provides +better reliability since a precompiled driver might depend on libraries or +kernel features that are not present in a given Linux installation. + +The 3 files necessary to build Linux device driver are dl2k.c, dl2k.h and +Makefile. To compile, the Linux installation must include the gcc compiler, +the kernel source, and the kernel headers. The Linux driver supports Linux +Kernels 2.4.7. Copy the files to a directory and enter the following command +to compile and link the driver: + +CD-ROM drive +------------ + +:: + + [root@XXX /] mkdir cdrom + [root@XXX /] mount -r -t iso9660 -o conv=auto /dev/cdrom /cdrom + [root@XXX /] cd root + [root@XXX /root] mkdir dl2k + [root@XXX /root] cd dl2k + [root@XXX dl2k] cp /cdrom/linux/dl2k.tgz /root/dl2k + [root@XXX dl2k] tar xfvz dl2k.tgz + [root@XXX dl2k] make all + +Floppy disc drive +----------------- + +:: + + [root@XXX /] cd root + [root@XXX /root] mkdir dl2k + [root@XXX /root] cd dl2k + [root@XXX dl2k] mcopy a:/linux/dl2k.tgz /root/dl2k + [root@XXX dl2k] tar xfvz dl2k.tgz + [root@XXX dl2k] make all + +Installing the Driver +===================== + +Manual Installation +------------------- + + Once the driver has been compiled, it must be loaded, enabled, and bound + to a protocol stack in order to establish network connectivity. To load a + module enter the command:: + + insmod dl2k.o + + or:: + + insmod dl2k.o <optional parameter> ; add parameter + +--------------------------------------------------------- + + example:: + + insmod dl2k.o media=100mbps_hd + + or:: + + insmod dl2k.o media=3 + + or:: + + insmod dl2k.o media=3,2 ; for 2 cards + +--------------------------------------------------------- + + Please reference the list of the command line parameters supported by + the Linux device driver below. + + The insmod command only loads the driver and gives it a name of the form + eth0, eth1, etc. To bring the NIC into an operational state, + it is necessary to issue the following command:: + + ifconfig eth0 up + + Finally, to bind the driver to the active protocol (e.g., TCP/IP with + Linux), enter the following command:: + + ifup eth0 + + Note that this is meaningful only if the system can find a configuration + script that contains the necessary network information. A sample will be + given in the next paragraph. + + The commands to unload a driver are as follows:: + + ifdown eth0 + ifconfig eth0 down + rmmod dl2k.o + + The following are the commands to list the currently loaded modules and + to see the current network configuration:: + + lsmod + ifconfig + + +Automated Installation +---------------------- + This section describes how to install the driver such that it is + automatically loaded and configured at boot time. The following description + is based on a Red Hat 6.0/7.0 distribution, but it can easily be ported to + other distributions as well. + +Red Hat v6.x/v7.x +----------------- + 1. Copy dl2k.o to the network modules directory, typically + /lib/modules/2.x.x-xx/net or /lib/modules/2.x.x/kernel/drivers/net. + 2. Locate the boot module configuration file, most commonly in the + /etc/modprobe.d/ directory. Add the following lines:: + + alias ethx dl2k + options dl2k <optional parameters> + + where ethx will be eth0 if the NIC is the only ethernet adapter, eth1 if + one other ethernet adapter is installed, etc. Refer to the table in the + previous section for the list of optional parameters. + 3. Locate the network configuration scripts, normally the + /etc/sysconfig/network-scripts directory, and create a configuration + script named ifcfg-ethx that contains network information. + 4. Note that for most Linux distributions, Red Hat included, a configuration + utility with a graphical user interface is provided to perform steps 2 + and 3 above. + + +Parameter Description +===================== +You can install this driver without any additional parameter. However, if you +are going to have extensive functions then it is necessary to set extra +parameter. Below is a list of the command line parameters supported by the +Linux device +driver. + + +=============================== ============================================== +mtu=packet_size Specifies the maximum packet size. default + is 1500. + +media=media_type Specifies the media type the NIC operates at. + autosense Autosensing active media. + + =========== ========================= + 10mbps_hd 10Mbps half duplex. + 10mbps_fd 10Mbps full duplex. + 100mbps_hd 100Mbps half duplex. + 100mbps_fd 100Mbps full duplex. + 1000mbps_fd 1000Mbps full duplex. + 1000mbps_hd 1000Mbps half duplex. + 0 Autosensing active media. + 1 10Mbps half duplex. + 2 10Mbps full duplex. + 3 100Mbps half duplex. + 4 100Mbps full duplex. + 5 1000Mbps half duplex. + 6 1000Mbps full duplex. + =========== ========================= + + By default, the NIC operates at autosense. + 1000mbps_fd and 1000mbps_hd types are only + available for fiber adapter. + +vlan=n Specifies the VLAN ID. If vlan=0, the + Virtual Local Area Network (VLAN) function is + disable. + +jumbo=[0|1] Specifies the jumbo frame support. If jumbo=1, + the NIC accept jumbo frames. By default, this + function is disabled. + Jumbo frame usually improve the performance + int gigabit. + This feature need jumbo frame compatible + remote. + +rx_coalesce=m Number of rx frame handled each interrupt. +rx_timeout=n Rx DMA wait time for an interrupt. + If set rx_coalesce > 0, hardware only assert + an interrupt for m frames. Hardware won't + assert rx interrupt until m frames received or + reach timeout of n * 640 nano seconds. + Set proper rx_coalesce and rx_timeout can + reduce congestion collapse and overload which + has been a bottleneck for high speed network. + + For example, rx_coalesce=10 rx_timeout=800. + that is, hardware assert only 1 interrupt + for 10 frames received or timeout of 512 us. + +tx_coalesce=n Number of tx frame handled each interrupt. + Set n > 1 can reduce the interrupts + congestion usually lower performance of + high speed network card. Default is 16. + +tx_flow=[1|0] Specifies the Tx flow control. If tx_flow=0, + the Tx flow control disable else driver + autodetect. +rx_flow=[1|0] Specifies the Rx flow control. If rx_flow=0, + the Rx flow control enable else driver + autodetect. +=============================== ============================================== + + +Configuration Script Sample +=========================== +Here is a sample of a simple configuration script:: + + DEVICE=eth0 + USERCTL=no + ONBOOT=yes + POOTPROTO=none + BROADCAST=207.200.5.255 + NETWORK=207.200.5.0 + NETMASK=255.255.255.0 + IPADDR=207.200.5.2 + + +Troubleshooting +=============== +Q1. Source files contain ^ M behind every line. + + Make sure all files are Unix file format (no LF). Try the following + shell command to convert files:: + + cat dl2k.c | col -b > dl2k.tmp + mv dl2k.tmp dl2k.c + + OR:: + + cat dl2k.c | tr -d "\r" > dl2k.tmp + mv dl2k.tmp dl2k.c + +Q2: Could not find header files (``*.h``)? + + To compile the driver, you need kernel header files. After + installing the kernel source, the header files are usually located in + /usr/src/linux/include, which is the default include directory configured + in Makefile. For some distributions, there is a copy of header files in + /usr/src/include/linux and /usr/src/include/asm, that you can change the + INCLUDEDIR in Makefile to /usr/include without installing kernel source. + + Note that RH 7.0 didn't provide correct header files in /usr/include, + including those files will make a wrong version driver. + diff --git a/Documentation/networking/device_drivers/ethernet/freescale/dpaa.rst b/Documentation/networking/device_drivers/ethernet/freescale/dpaa.rst new file mode 100644 index 0000000000..241c6c6f6e --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/freescale/dpaa.rst @@ -0,0 +1,269 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============================== +The QorIQ DPAA Ethernet Driver +============================== + +Authors: +- Madalin Bucur <madalin.bucur@nxp.com> +- Camelia Groza <camelia.groza@nxp.com> + +.. Contents + + - DPAA Ethernet Overview + - DPAA Ethernet Supported SoCs + - Configuring DPAA Ethernet in your kernel + - DPAA Ethernet Frame Processing + - DPAA Ethernet Features + - DPAA IRQ Affinity and Receive Side Scaling + - Debugging + +DPAA Ethernet Overview +====================== + +DPAA stands for Data Path Acceleration Architecture and it is a +set of networking acceleration IPs that are available on several +generations of SoCs, both on PowerPC and ARM64. + +The Freescale DPAA architecture consists of a series of hardware blocks +that support Ethernet connectivity. The Ethernet driver depends upon the +following drivers in the Linux kernel: + + - Peripheral Access Memory Unit (PAMU) (* needed only for PPC platforms) + drivers/iommu/fsl_* + - Frame Manager (FMan) + drivers/net/ethernet/freescale/fman + - Queue Manager (QMan), Buffer Manager (BMan) + drivers/soc/fsl/qbman + +A simplified view of the dpaa_eth interfaces mapped to FMan MACs:: + + dpaa_eth /eth0\ ... /ethN\ + driver | | | | + ------------- ---- ----------- ---- ------------- + -Ports / Tx Rx \ ... / Tx Rx \ + FMan | | | | + -MACs | MAC0 | | MACN | + / dtsec0 \ ... / dtsecN \ (or tgec) + / \ / \(or memac) + --------- -------------- --- -------------- --------- + FMan, FMan Port, FMan SP, FMan MURAM drivers + --------------------------------------------------------- + FMan HW blocks: MURAM, MACs, Ports, SP + --------------------------------------------------------- + +The dpaa_eth relation to the QMan, BMan and FMan:: + + ________________________________ + dpaa_eth / eth0 \ + driver / \ + --------- -^- -^- -^- --- --------- + QMan driver / \ / \ / \ \ / | BMan | + |Rx | |Rx | |Tx | |Tx | | driver | + --------- |Dfl| |Err| |Cnf| |FQs| | | + QMan HW |FQ | |FQ | |FQs| | | | | + / \ / \ / \ \ / | | + --------- --- --- --- -v- --------- + | FMan QMI | | + | FMan HW FMan BMI | BMan HW | + ----------------------- -------- + +where the acronyms used above (and in the code) are: + +=============== =========================================================== +DPAA Data Path Acceleration Architecture +FMan DPAA Frame Manager +QMan DPAA Queue Manager +BMan DPAA Buffers Manager +QMI QMan interface in FMan +BMI BMan interface in FMan +FMan SP FMan Storage Profiles +MURAM Multi-user RAM in FMan +FQ QMan Frame Queue +Rx Dfl FQ default reception FQ +Rx Err FQ Rx error frames FQ +Tx Cnf FQ Tx confirmation FQs +Tx FQs transmission frame queues +dtsec datapath three speed Ethernet controller (10/100/1000 Mbps) +tgec ten gigabit Ethernet controller (10 Gbps) +memac multirate Ethernet MAC (10/100/1000/10000) +=============== =========================================================== + +DPAA Ethernet Supported SoCs +============================ + +The DPAA drivers enable the Ethernet controllers present on the following SoCs: + +PPC +- P1023 +- P2041 +- P3041 +- P4080 +- P5020 +- P5040 +- T1023 +- T1024 +- T1040 +- T1042 +- T2080 +- T4240 +- B4860 + +ARM +- LS1043A +- LS1046A + +Configuring DPAA Ethernet in your kernel +======================================== + +To enable the DPAA Ethernet driver, the following Kconfig options are required:: + + # common for arch/arm64 and arch/powerpc platforms + CONFIG_FSL_DPAA=y + CONFIG_FSL_FMAN=y + CONFIG_FSL_DPAA_ETH=y + CONFIG_FSL_XGMAC_MDIO=y + + # for arch/powerpc only + CONFIG_FSL_PAMU=y + + # common options needed for the PHYs used on the RDBs + CONFIG_VITESSE_PHY=y + CONFIG_REALTEK_PHY=y + CONFIG_AQUANTIA_PHY=y + +DPAA Ethernet Frame Processing +============================== + +On Rx, buffers for the incoming frames are retrieved from the buffers found +in the dedicated interface buffer pool. The driver initializes and seeds these +with one page buffers. + +On Tx, all transmitted frames are returned to the driver through Tx +confirmation frame queues. The driver is then responsible for freeing the +buffers. In order to do this properly, a backpointer is added to the buffer +before transmission that points to the skb. When the buffer returns to the +driver on a confirmation FQ, the skb can be correctly consumed. + +DPAA Ethernet Features +====================== + +Currently the DPAA Ethernet driver enables the basic features required for +a Linux Ethernet driver. The support for advanced features will be added +gradually. + +The driver has Rx and Tx checksum offloading for UDP and TCP. Currently the Rx +checksum offload feature is enabled by default and cannot be controlled through +ethtool. Also, rx-flow-hash and rx-hashing was added. The addition of RSS +provides a big performance boost for the forwarding scenarios, allowing +different traffic flows received by one interface to be processed by different +CPUs in parallel. + +The driver has support for multiple prioritized Tx traffic classes. Priorities +range from 0 (lowest) to 3 (highest). These are mapped to HW workqueues with +strict priority levels. Each traffic class contains NR_CPU TX queues. By +default, only one traffic class is enabled and the lowest priority Tx queues +are used. Higher priority traffic classes can be enabled with the mqprio +qdisc. For example, all four traffic classes are enabled on an interface with +the following command. Furthermore, skb priority levels are mapped to traffic +classes as follows: + + * priorities 0 to 3 - traffic class 0 (low priority) + * priorities 4 to 7 - traffic class 1 (medium-low priority) + * priorities 8 to 11 - traffic class 2 (medium-high priority) + * priorities 12 to 15 - traffic class 3 (high priority) + +:: + + tc qdisc add dev <int> root handle 1: \ + mqprio num_tc 4 map 0 0 0 0 1 1 1 1 2 2 2 2 3 3 3 3 hw 1 + +DPAA IRQ Affinity and Receive Side Scaling +========================================== + +Traffic coming on the DPAA Rx queues or on the DPAA Tx confirmation +queues is seen by the CPU as ingress traffic on a certain portal. +The DPAA QMan portal interrupts are affined each to a certain CPU. +The same portal interrupt services all the QMan portal consumers. + +By default the DPAA Ethernet driver enables RSS, making use of the +DPAA FMan Parser and Keygen blocks to distribute traffic on 128 +hardware frame queues using a hash on IP v4/v6 source and destination +and L4 source and destination ports, in present in the received frame. +When RSS is disabled, all traffic received by a certain interface is +received on the default Rx frame queue. The default DPAA Rx frame +queues are configured to put the received traffic into a pool channel +that allows any available CPU portal to dequeue the ingress traffic. +The default frame queues have the HOLDACTIVE option set, ensuring that +traffic bursts from a certain queue are serviced by the same CPU. +This ensures a very low rate of frame reordering. A drawback of this +is that only one CPU at a time can service the traffic received by a +certain interface when RSS is not enabled. + +To implement RSS, the DPAA Ethernet driver allocates an extra set of +128 Rx frame queues that are configured to dedicated channels, in a +round-robin manner. The mapping of the frame queues to CPUs is now +hardcoded, there is no indirection table to move traffic for a certain +FQ (hash result) to another CPU. The ingress traffic arriving on one +of these frame queues will arrive at the same portal and will always +be processed by the same CPU. This ensures intra-flow order preservation +and workload distribution for multiple traffic flows. + +RSS can be turned off for a certain interface using ethtool, i.e.:: + + # ethtool -N fm1-mac9 rx-flow-hash tcp4 "" + +To turn it back on, one needs to set rx-flow-hash for tcp4/6 or udp4/6:: + + # ethtool -N fm1-mac9 rx-flow-hash udp4 sfdn + +There is no independent control for individual protocols, any command +run for one of tcp4|udp4|ah4|esp4|sctp4|tcp6|udp6|ah6|esp6|sctp6 is +going to control the rx-flow-hashing for all protocols on that interface. + +Besides using the FMan Keygen computed hash for spreading traffic on the +128 Rx FQs, the DPAA Ethernet driver also sets the skb hash value when +the NETIF_F_RXHASH feature is on (active by default). This can be turned +on or off through ethtool, i.e.:: + + # ethtool -K fm1-mac9 rx-hashing off + # ethtool -k fm1-mac9 | grep hash + receive-hashing: off + # ethtool -K fm1-mac9 rx-hashing on + Actual changes: + receive-hashing: on + # ethtool -k fm1-mac9 | grep hash + receive-hashing: on + +Please note that Rx hashing depends upon the rx-flow-hashing being on +for that interface - turning off rx-flow-hashing will also disable the +rx-hashing (without ethtool reporting it as off as that depends on the +NETIF_F_RXHASH feature flag). + +Debugging +========= + +The following statistics are exported for each interface through ethtool: + + - interrupt count per CPU + - Rx packets count per CPU + - Tx packets count per CPU + - Tx confirmed packets count per CPU + - Tx S/G frames count per CPU + - Tx error count per CPU + - Rx error count per CPU + - Rx error count per type + - congestion related statistics: + + - congestion status + - time spent in congestion + - number of time the device entered congestion + - dropped packets count per cause + +The driver also exports the following information in sysfs: + + - the FQ IDs for each FQ type + /sys/devices/platform/soc/<addr>.fman/<addr>.ethernet/dpaa-ethernet.<id>/net/fm<nr>-mac<nr>/fqids + + - the ID of the buffer pool in use + /sys/devices/platform/soc/<addr>.fman/<addr>.ethernet/dpaa-ethernet.<id>/net/fm<nr>-mac<nr>/bpids diff --git a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/dpio-driver.rst b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/dpio-driver.rst new file mode 100644 index 0000000000..e4ebfe62a1 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/dpio-driver.rst @@ -0,0 +1,161 @@ +.. include:: <isonum.txt> + +=================================== +DPAA2 DPIO (Data Path I/O) Overview +=================================== + +:Copyright: |copy| 2016-2018 NXP + +This document provides an overview of the Freescale DPAA2 DPIO +drivers + +Introduction +============ + +A DPAA2 DPIO (Data Path I/O) is a hardware object that provides +interfaces to enqueue and dequeue frames to/from network interfaces +and other accelerators. A DPIO also provides hardware buffer +pool management for network interfaces. + +This document provides an overview the Linux DPIO driver, its +subcomponents, and its APIs. + +See +Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst +for a general overview of DPAA2 and the general DPAA2 driver architecture +in Linux. + +Driver Overview +--------------- + +The DPIO driver is bound to DPIO objects discovered on the fsl-mc bus and +provides services that: + + A. allow other drivers, such as the Ethernet driver, to enqueue and dequeue + frames for their respective objects + B. allow drivers to register callbacks for data availability notifications + when data becomes available on a queue or channel + C. allow drivers to manage hardware buffer pools + +The Linux DPIO driver consists of 3 primary components-- + DPIO object driver-- fsl-mc driver that manages the DPIO object + + DPIO service-- provides APIs to other Linux drivers for services + + QBman portal interface-- sends portal commands, gets responses:: + + fsl-mc other + bus drivers + | | + +---+----+ +------+-----+ + |DPIO obj| |DPIO service| + | driver |---| (DPIO) | + +--------+ +------+-----+ + | + +------+-----+ + | QBman | + | portal i/f | + +------------+ + | + hardware + + +The diagram below shows how the DPIO driver components fit with the other +DPAA2 Linux driver components:: + + +------------+ + | OS Network | + | Stack | + +------------+ +------------+ + | Allocator |. . . . . . . | Ethernet | + |(DPMCP,DPBP)| | (DPNI) | + +-.----------+ +---+---+----+ + . . ^ | + . . <data avail, | |<enqueue, + . . tx confirm> | | dequeue> + +-------------+ . | | + | DPRC driver | . +--------+ +------------+ + | (DPRC) | . . |DPIO obj| |DPIO service| + +----------+--+ | driver |-| (DPIO) | + | +--------+ +------+-----+ + |<dev add/remove> +------|-----+ + | | QBman | + +----+--------------+ | portal i/f | + | MC-bus driver | +------------+ + | | | + | /soc/fsl-mc | | + +-------------------+ | + | + =========================================|=========|======================== + +-+--DPIO---|-----------+ + | | | + | QBman Portal | + +-----------------------+ + + ============================================================================ + + +DPIO Object Driver (dpio-driver.c) +---------------------------------- + + The dpio-driver component registers with the fsl-mc bus to handle objects of + type "dpio". The implementation of probe() handles basic initialization + of the DPIO including mapping of the DPIO regions (the QBman SW portal) + and initializing interrupts and registering irq handlers. The dpio-driver + registers the probed DPIO with dpio-service. + +DPIO service (dpio-service.c, dpaa2-io.h) +------------------------------------------ + + The dpio service component provides queuing, notification, and buffers + management services to DPAA2 drivers, such as the Ethernet driver. A system + will typically allocate 1 DPIO object per CPU to allow queuing operations + to happen simultaneously across all CPUs. + + Notification handling + dpaa2_io_service_register() + + dpaa2_io_service_deregister() + + dpaa2_io_service_rearm() + + Queuing + dpaa2_io_service_pull_fq() + + dpaa2_io_service_pull_channel() + + dpaa2_io_service_enqueue_fq() + + dpaa2_io_service_enqueue_qd() + + dpaa2_io_store_create() + + dpaa2_io_store_destroy() + + dpaa2_io_store_next() + + Buffer pool management + dpaa2_io_service_release() + + dpaa2_io_service_acquire() + +QBman portal interface (qbman-portal.c) +--------------------------------------- + + The qbman-portal component provides APIs to do the low level hardware + bit twiddling for operations such as: + + - initializing Qman software portals + - building and sending portal commands + - portal interrupt configuration and processing + + The qbman-portal APIs are not public to other drivers, and are + only used by dpio-service. + +Other (dpaa2-fd.h, dpaa2-global.h) +---------------------------------- + + Frame descriptor and scatter-gather definitions and the APIs used to + manipulate them are defined in dpaa2-fd.h. + + Dequeue result struct and parsing APIs are defined in dpaa2-global.h. diff --git a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/ethernet-driver.rst b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/ethernet-driver.rst new file mode 100644 index 0000000000..682f3986c1 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/ethernet-driver.rst @@ -0,0 +1,186 @@ +.. SPDX-License-Identifier: GPL-2.0 +.. include:: <isonum.txt> + +=============================== +DPAA2 Ethernet driver +=============================== + +:Copyright: |copy| 2017-2018 NXP + +This file provides documentation for the Freescale DPAA2 Ethernet driver. + +Supported Platforms +=================== +This driver provides networking support for Freescale DPAA2 SoCs, e.g. +LS2080A, LS2088A, LS1088A. + + +Architecture Overview +===================== +Unlike regular NICs, in the DPAA2 architecture there is no single hardware block +representing network interfaces; instead, several separate hardware resources +concur to provide the networking functionality: + +- network interfaces +- queues, channels +- buffer pools +- MAC/PHY + +All hardware resources are allocated and configured through the Management +Complex (MC) portals. MC abstracts most of these resources as DPAA2 objects +and exposes ABIs through which they can be configured and controlled. A few +hardware resources, like queues, do not have a corresponding MC object and +are treated as internal resources of other objects. + +For a more detailed description of the DPAA2 architecture and its object +abstractions see +*Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst*. + +Each Linux net device is built on top of a Datapath Network Interface (DPNI) +object and uses Buffer Pools (DPBPs), I/O Portals (DPIOs) and Concentrators +(DPCONs). + +Configuration interface:: + + ----------------------- + | DPAA2 Ethernet Driver | + ----------------------- + . . . + . . . + . . . . . . . . . . . . + . . . + . . . + ---------- ---------- ----------- + | DPBP API | | DPNI API | | DPCON API | + ---------- ---------- ----------- + . . . software + ======= . ========== . ============ . =================== + . . . hardware + ------------------------------------------ + | MC hardware portals | + ------------------------------------------ + . . . + . . . + ------ ------ ------- + | DPBP | | DPNI | | DPCON | + ------ ------ ------- + +The DPNIs are network interfaces without a direct one-on-one mapping to PHYs. +DPBPs represent hardware buffer pools. Packet I/O is performed in the context +of DPCON objects, using DPIO portals for managing and communicating with the +hardware resources. + +Datapath (I/O) interface:: + + ----------------------------------------------- + | DPAA2 Ethernet Driver | + ----------------------------------------------- + | ^ ^ | | + | | | | | + enqueue| dequeue| data | dequeue| seed | + (Tx) | (Rx, TxC)| avail.| request| buffers| + | | notify| | | + | | | | | + V | | V V + ----------------------------------------------- + | DPIO Driver | + ----------------------------------------------- + | | | | | software + | | | | | ================ + | | | | | hardware + ----------------------------------------------- + | I/O hardware portals | + ----------------------------------------------- + | ^ ^ | | + | | | | | + | | | V | + V | ================ V + ---------------------- | ------------- + queues ---------------------- | | Buffer pool | + ---------------------- | ------------- + ======================= + Channel + +Datapath I/O (DPIO) portals provide enqueue and dequeue services, data +availability notifications and buffer pool management. DPIOs are shared between +all DPAA2 objects (and implicitly all DPAA2 kernel drivers) that work with data +frames, but must be affine to the CPUs for the purpose of traffic distribution. + +Frames are transmitted and received through hardware frame queues, which can be +grouped in channels for the purpose of hardware scheduling. The Ethernet driver +enqueues TX frames on egress queues and after transmission is complete a TX +confirmation frame is sent back to the CPU. + +When frames are available on ingress queues, a data availability notification +is sent to the CPU; notifications are raised per channel, so even if multiple +queues in the same channel have available frames, only one notification is sent. +After a channel fires a notification, is must be explicitly rearmed. + +Each network interface can have multiple Rx, Tx and confirmation queues affined +to CPUs, and one channel (DPCON) for each CPU that services at least one queue. +DPCONs are used to distribute ingress traffic to different CPUs via the cores' +affine DPIOs. + +The role of hardware buffer pools is storage of ingress frame data. Each network +interface has a privately owned buffer pool which it seeds with kernel allocated +buffers. + + +DPNIs are decoupled from PHYs; a DPNI can be connected to a PHY through a DPMAC +object or to another DPNI through an internal link, but the connection is +managed by MC and completely transparent to the Ethernet driver. + +:: + + --------- --------- --------- + | eth if1 | | eth if2 | | eth ifn | + --------- --------- --------- + . . . + . . . + . . . + --------------------------- + | DPAA2 Ethernet Driver | + --------------------------- + . . . + . . . + . . . + ------ ------ ------ ------- + | DPNI | | DPNI | | DPNI | | DPMAC |----+ + ------ ------ ------ ------- | + | | | | | + | | | | ----- + =========== ================== | PHY | + ----- + +Creating a Network Interface +============================ +A net device is created for each DPNI object probed on the MC bus. Each DPNI has +a number of properties which determine the network interface configuration +options and associated hardware resources. + +DPNI objects (and the other DPAA2 objects needed for a network interface) can be +added to a container on the MC bus in one of two ways: statically, through a +Datapath Layout Binary file (DPL) that is parsed by MC at boot time; or created +dynamically at runtime, via the DPAA2 objects APIs. + + +Features & Offloads +=================== +Hardware checksum offloading is supported for TCP and UDP over IPv4/6 frames. +The checksum offloads can be independently configured on RX and TX through +ethtool. + +Hardware offload of unicast and multicast MAC filtering is supported on the +ingress path and permanently enabled. + +Scatter-gather frames are supported on both RX and TX paths. On TX, SG support +is configurable via ethtool; on RX it is always enabled. + +The DPAA2 hardware can process jumbo Ethernet frames of up to 10K bytes. + +The Ethernet driver defines a static flow hashing scheme that distributes +traffic based on a 5-tuple key: src IP, dst IP, IP proto, L4 src port, +L4 dst port. No user configuration is supported for now. + +Hardware specific statistics for the network interface as well as some +non-standard driver stats can be consulted through ethtool -S option. diff --git a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/index.rst b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/index.rst new file mode 100644 index 0000000000..62f4a4aff6 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/index.rst @@ -0,0 +1,12 @@ +=================== +DPAA2 Documentation +=================== + +.. toctree:: + :maxdepth: 1 + + overview + dpio-driver + ethernet-driver + mac-phy-support + switch-driver diff --git a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/mac-phy-support.rst b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/mac-phy-support.rst new file mode 100644 index 0000000000..e2a36d0d88 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/mac-phy-support.rst @@ -0,0 +1,194 @@ +.. SPDX-License-Identifier: GPL-2.0 +.. include:: <isonum.txt> + +======================= +DPAA2 MAC / PHY support +======================= + +:Copyright: |copy| 2019 NXP + +Overview +-------- + +The DPAA2 MAC / PHY support consists of a set of APIs that help DPAA2 network +drivers (dpaa2-eth, dpaa2-ethsw) interact with the PHY library. + +DPAA2 Software Architecture +--------------------------- + +Among other DPAA2 objects, the fsl-mc bus exports DPNI objects (abstracting a +network interface) and DPMAC objects (abstracting a MAC). The dpaa2-eth driver +probes on the DPNI object and connects to and configures a DPMAC object with +the help of phylink. + +Data connections may be established between a DPNI and a DPMAC, or between two +DPNIs. Depending on the connection type, the netif_carrier_[on/off] is handled +directly by the dpaa2-eth driver or by phylink. + +.. code-block:: none + + Sources of abstracted link state information presented by the MC firmware + + +--------------------------------------+ + +------------+ +---------+ | xgmac_mdio | + | net_device | | phylink |--| +-----+ +-----+ +-----+ +-----+ | + +------------+ +---------+ | | PHY | | PHY | | PHY | | PHY | | + | | | +-----+ +-----+ +-----+ +-----+ | + +------------------------------------+ | External MDIO bus | + | dpaa2-eth | +--------------------------------------+ + +------------------------------------+ + | | Linux + ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + | | MC firmware + | /| V + +----------+ / | +----------+ + | | / | | | + | | | | | | + | DPNI |<------| |<------| DPMAC | + | | | | | | + | | \ |<---+ | | + +----------+ \ | | +----------+ + \| | + | + +--------------------------------------+ + | MC firmware polling MAC PCS for link | + | +-----+ +-----+ +-----+ +-----+ | + | | PCS | | PCS | | PCS | | PCS | | + | +-----+ +-----+ +-----+ +-----+ | + | Internal MDIO bus | + +--------------------------------------+ + + +Depending on an MC firmware configuration setting, each MAC may be in one of two modes: + +- DPMAC_LINK_TYPE_FIXED: the link state management is handled exclusively by + the MC firmware by polling the MAC PCS. Without the need to register a + phylink instance, the dpaa2-eth driver will not bind to the connected dpmac + object at all. + +- DPMAC_LINK_TYPE_PHY: The MC firmware is left waiting for link state update + events, but those are in fact passed strictly between the dpaa2-mac (based on + phylink) and its attached net_device driver (dpaa2-eth, dpaa2-ethsw), + effectively bypassing the firmware. + +Implementation +-------------- + +At probe time or when a DPNI's endpoint is dynamically changed, the dpaa2-eth +is responsible to find out if the peer object is a DPMAC and if this is the +case, to integrate it with PHYLINK using the dpaa2_mac_connect() API, which +will do the following: + + - look up the device tree for PHYLINK-compatible of binding (phy-handle) + - will create a PHYLINK instance associated with the received net_device + - connect to the PHY using phylink_of_phy_connect() + +The following phylink_mac_ops callback are implemented: + + - .validate() will populate the supported linkmodes with the MAC capabilities + only when the phy_interface_t is RGMII_* (at the moment, this is the only + link type supported by the driver). + + - .mac_config() will configure the MAC in the new configuration using the + dpmac_set_link_state() MC firmware API. + + - .mac_link_up() / .mac_link_down() will update the MAC link using the same + API described above. + +At driver unbind() or when the DPNI object is disconnected from the DPMAC, the +dpaa2-eth driver calls dpaa2_mac_disconnect() which will, in turn, disconnect +from the PHY and destroy the PHYLINK instance. + +In case of a DPNI-DPMAC connection, an 'ip link set dev eth0 up' would start +the following sequence of operations: + +(1) phylink_start() called from .dev_open(). +(2) The .mac_config() and .mac_link_up() callbacks are called by PHYLINK. +(3) In order to configure the HW MAC, the MC Firmware API + dpmac_set_link_state() is called. +(4) The firmware will eventually setup the HW MAC in the new configuration. +(5) A netif_carrier_on() call is made directly from PHYLINK on the associated + net_device. +(6) The dpaa2-eth driver handles the LINK_STATE_CHANGE irq in order to + enable/disable Rx taildrop based on the pause frame settings. + +.. code-block:: none + + +---------+ +---------+ + | PHYLINK |-------------->| eth0 | + +---------+ (5) +---------+ + (1) ^ | + | | + | v (2) + +-----------------------------------+ + | dpaa2-eth | + +-----------------------------------+ + | ^ (6) + | | + v (3) | + +---------+---------------+---------+ + | DPMAC | | DPNI | + +---------+ +---------+ + | MC Firmware | + +-----------------------------------+ + | + | + v (4) + +-----------------------------------+ + | HW MAC | + +-----------------------------------+ + +In case of a DPNI-DPNI connection, a usual sequence of operations looks like +the following: + +(1) ip link set dev eth0 up +(2) The dpni_enable() MC API called on the associated fsl_mc_device. +(3) ip link set dev eth1 up +(4) The dpni_enable() MC API called on the associated fsl_mc_device. +(5) The LINK_STATE_CHANGED irq is received by both instances of the dpaa2-eth + driver because now the operational link state is up. +(6) The netif_carrier_on() is called on the exported net_device from + link_state_update(). + +.. code-block:: none + + +---------+ +---------+ + | eth0 | | eth1 | + +---------+ +---------+ + | ^ ^ | + | | | | + (1) v | (6) (6) | v (3) + +---------+ +---------+ + |dpaa2-eth| |dpaa2-eth| + +---------+ +---------+ + | ^ ^ | + | | | | + (2) v | (5) (5) | v (4) + +---------+---------------+---------+ + | DPNI | | DPNI | + +---------+ +---------+ + | MC Firmware | + +-----------------------------------+ + + +Exported API +------------ + +Any DPAA2 driver that drivers endpoints of DPMAC objects should service its +_EVENT_ENDPOINT_CHANGED irq and connect/disconnect from the associated DPMAC +when necessary using the below listed API:: + + - int dpaa2_mac_connect(struct dpaa2_mac *mac); + - void dpaa2_mac_disconnect(struct dpaa2_mac *mac); + +A phylink integration is necessary only when the partner DPMAC is not of +``TYPE_FIXED``. This means it is either of ``TYPE_PHY``, or of +``TYPE_BACKPLANE`` (the difference being the two that in the ``TYPE_BACKPLANE`` +mode, the MC firmware does not access the PCS registers). One can check for +this condition using the following helper:: + + - static inline bool dpaa2_mac_is_type_phy(struct dpaa2_mac *mac); + +Before connection to a MAC, the caller must allocate and populate the +dpaa2_mac structure with the associated net_device, a pointer to the MC portal +to be used and the actual fsl_mc_device structure of the DPMAC. diff --git a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst new file mode 100644 index 0000000000..1996477292 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst @@ -0,0 +1,406 @@ +.. include:: <isonum.txt> + +========================================================= +DPAA2 (Data Path Acceleration Architecture Gen2) Overview +========================================================= + +:Copyright: |copy| 2015 Freescale Semiconductor Inc. +:Copyright: |copy| 2018 NXP + +This document provides an overview of the Freescale DPAA2 architecture +and how it is integrated into the Linux kernel. + +Introduction +============ + +DPAA2 is a hardware architecture designed for high-speeed network +packet processing. DPAA2 consists of sophisticated mechanisms for +processing Ethernet packets, queue management, buffer management, +autonomous L2 switching, virtual Ethernet bridging, and accelerator +(e.g. crypto) sharing. + +A DPAA2 hardware component called the Management Complex (or MC) manages the +DPAA2 hardware resources. The MC provides an object-based abstraction for +software drivers to use the DPAA2 hardware. +The MC uses DPAA2 hardware resources such as queues, buffer pools, and +network ports to create functional objects/devices such as network +interfaces, an L2 switch, or accelerator instances. +The MC provides memory-mapped I/O command interfaces (MC portals) +which DPAA2 software drivers use to operate on DPAA2 objects. + +The diagram below shows an overview of the DPAA2 resource management +architecture:: + + +--------------------------------------+ + | OS | + | DPAA2 drivers | + | | | + +-----------------------------|--------+ + | + | (create,discover,connect + | config,use,destroy) + | + DPAA2 | + +------------------------| mc portal |-+ + | | | + | +- - - - - - - - - - - - -V- - -+ | + | | | | + | | Management Complex (MC) | | + | | | | + | +- - - - - - - - - - - - - - - -+ | + | | + | Hardware Hardware | + | Resources Objects | + | --------- ------- | + | -queues -DPRC | + | -buffer pools -DPMCP | + | -Eth MACs/ports -DPIO | + | -network interface -DPNI | + | profiles -DPMAC | + | -queue portals -DPBP | + | -MC portals ... | + | ... | + | | + +--------------------------------------+ + + +The MC mediates operations such as create, discover, +connect, configuration, and destroy. Fast-path operations +on data, such as packet transmit/receive, are not mediated by +the MC and are done directly using memory mapped regions in +DPIO objects. + +Overview of DPAA2 Objects +========================= + +The section provides a brief overview of some key DPAA2 objects. +A simple scenario is described illustrating the objects involved +in creating a network interfaces. + +DPRC (Datapath Resource Container) +---------------------------------- + +A DPRC is a container object that holds all the other +types of DPAA2 objects. In the example diagram below there +are 8 objects of 5 types (DPMCP, DPIO, DPBP, DPNI, and DPMAC) +in the container. + +:: + + +---------------------------------------------------------+ + | DPRC | + | | + | +-------+ +-------+ +-------+ +-------+ +-------+ | + | | DPMCP | | DPIO | | DPBP | | DPNI | | DPMAC | | + | +-------+ +-------+ +-------+ +---+---+ +---+---+ | + | | DPMCP | | DPIO | | + | +-------+ +-------+ | + | | DPMCP | | + | +-------+ | + | | + +---------------------------------------------------------+ + +From the point of view of an OS, a DPRC behaves similar to a plug and +play bus, like PCI. DPRC commands can be used to enumerate the contents +of the DPRC, discover the hardware objects present (including mappable +regions and interrupts). + +:: + + DPRC.1 (bus) + | + +--+--------+-------+-------+-------+ + | | | | | + DPMCP.1 DPIO.1 DPBP.1 DPNI.1 DPMAC.1 + DPMCP.2 DPIO.2 + DPMCP.3 + +Hardware objects can be created and destroyed dynamically, providing +the ability to hot plug/unplug objects in and out of the DPRC. + +A DPRC has a mappable MMIO region (an MC portal) that can be used +to send MC commands. It has an interrupt for status events (like +hotplug). +All objects in a container share the same hardware "isolation context". +This means that with respect to an IOMMU the isolation granularity +is at the DPRC (container) level, not at the individual object +level. + +DPRCs can be defined statically and populated with objects +via a config file passed to the MC when firmware starts it. + +DPAA2 Objects for an Ethernet Network Interface +----------------------------------------------- + +A typical Ethernet NIC is monolithic-- the NIC device contains TX/RX +queuing mechanisms, configuration mechanisms, buffer management, +physical ports, and interrupts. DPAA2 uses a more granular approach +utilizing multiple hardware objects. Each object provides specialized +functions. Groups of these objects are used by software to provide +Ethernet network interface functionality. This approach provides +efficient use of finite hardware resources, flexibility, and +performance advantages. + +The diagram below shows the objects needed for a simple +network interface configuration on a system with 2 CPUs. + +:: + + +---+---+ +---+---+ + CPU0 CPU1 + +---+---+ +---+---+ + | | + +---+---+ +---+---+ + DPIO DPIO + +---+---+ +---+---+ + \ / + \ / + \ / + +---+---+ + DPNI --- DPBP,DPMCP + +---+---+ + | + | + +---+---+ + DPMAC + +---+---+ + | + port/PHY + +Below the objects are described. For each object a brief description +is provided along with a summary of the kinds of operations the object +supports and a summary of key resources of the object (MMIO regions +and IRQs). + +DPMAC (Datapath Ethernet MAC) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +Represents an Ethernet MAC, a hardware device that connects to an Ethernet +PHY and allows physical transmission and reception of Ethernet frames. + +- MMIO regions: none +- IRQs: DPNI link change +- commands: set link up/down, link config, get stats, + IRQ config, enable, reset + +DPNI (Datapath Network Interface) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +Contains TX/RX queues, network interface configuration, and RX buffer pool +configuration mechanisms. The TX/RX queues are in memory and are identified +by queue number. + +- MMIO regions: none +- IRQs: link state +- commands: port config, offload config, queue config, + parse/classify config, IRQ config, enable, reset + +DPIO (Datapath I/O) +~~~~~~~~~~~~~~~~~~~ +Provides interfaces to enqueue and dequeue +packets and do hardware buffer pool management operations. The DPAA2 +architecture separates the mechanism to access queues (the DPIO object) +from the queues themselves. The DPIO provides an MMIO interface to +enqueue/dequeue packets. To enqueue something a descriptor is written +to the DPIO MMIO region, which includes the target queue number. +There will typically be one DPIO assigned to each CPU. This allows all +CPUs to simultaneously perform enqueue/dequeued operations. DPIOs are +expected to be shared by different DPAA2 drivers. + +- MMIO regions: queue operations, buffer management +- IRQs: data availability, congestion notification, buffer + pool depletion +- commands: IRQ config, enable, reset + +DPBP (Datapath Buffer Pool) +~~~~~~~~~~~~~~~~~~~~~~~~~~~ +Represents a hardware buffer pool. + +- MMIO regions: none +- IRQs: none +- commands: enable, reset + +DPMCP (Datapath MC Portal) +~~~~~~~~~~~~~~~~~~~~~~~~~~ +Provides an MC command portal. +Used by drivers to send commands to the MC to manage +objects. + +- MMIO regions: MC command portal +- IRQs: command completion +- commands: IRQ config, enable, reset + +Object Connections +================== +Some objects have explicit relationships that must +be configured: + +- DPNI <--> DPMAC +- DPNI <--> DPNI +- DPNI <--> L2-switch-port + + A DPNI must be connected to something such as a DPMAC, + another DPNI, or L2 switch port. The DPNI connection + is made via a DPRC command. + +:: + + +-------+ +-------+ + | DPNI | | DPMAC | + +---+---+ +---+---+ + | | + +==========+ + +- DPNI <--> DPBP + + A network interface requires a 'buffer pool' (DPBP + object) which provides a list of pointers to memory + where received Ethernet data is to be copied. The + Ethernet driver configures the DPBPs associated with + the network interface. + +Interrupts +========== +All interrupts generated by DPAA2 objects are message +interrupts. At the hardware level message interrupts +generated by devices will normally have 3 components-- +1) a non-spoofable 'device-id' expressed on the hardware +bus, 2) an address, 3) a data value. + +In the case of DPAA2 devices/objects, all objects in the +same container/DPRC share the same 'device-id'. +For ARM-based SoC this is the same as the stream ID. + + +DPAA2 Linux Drivers Overview +============================ + +This section provides an overview of the Linux kernel drivers for +DPAA2-- 1) the bus driver and associated "DPAA2 infrastructure" +drivers and 2) functional object drivers (such as Ethernet). + +As described previously, a DPRC is a container that holds the other +types of DPAA2 objects. It is functionally similar to a plug-and-play +bus controller. +Each object in the DPRC is a Linux "device" and is bound to a driver. +The diagram below shows the Linux drivers involved in a networking +scenario and the objects bound to each driver. A brief description +of each driver follows. + +:: + + +------------+ + | OS Network | + | Stack | + +------------+ +------------+ + | Allocator |. . . . . . . | Ethernet | + |(DPMCP,DPBP)| | (DPNI) | + +-.----------+ +---+---+----+ + . . ^ | + . . <data avail, | | <enqueue, + . . tx confirm> | | dequeue> + +-------------+ . | | + | DPRC driver | . +---+---V----+ +---------+ + | (DPRC) | . . . . . .| DPIO driver| | MAC | + +----------+--+ | (DPIO) | | (DPMAC) | + | +------+-----+ +-----+---+ + |<dev add/remove> | | + | | | + +--------+----------+ | +--+---+ + | MC-bus driver | | | PHY | + | | | |driver| + | /bus/fsl-mc | | +--+---+ + +-------------------+ | | + | | + ========================= HARDWARE =========|=================|====== + DPIO | + | | + DPNI---DPBP | + | | + DPMAC | + | | + PHY ---------------+ + ============================================|======================== + +A brief description of each driver is provided below. + +MC-bus driver +------------- +The MC-bus driver is a platform driver and is probed from a +node in the device tree (compatible "fsl,qoriq-mc") passed in by boot +firmware. It is responsible for bootstrapping the DPAA2 kernel +infrastructure. +Key functions include: + +- registering a new bus type named "fsl-mc" with the kernel, + and implementing bus call-backs (e.g. match/uevent/dev_groups) +- implementing APIs for DPAA2 driver registration and for device + add/remove +- creates an MSI IRQ domain +- doing a 'device add' to expose the 'root' DPRC, in turn triggering + a bind of the root DPRC to the DPRC driver + +The binding for the MC-bus device-tree node can be consulted at +*Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt*. +The sysfs bind/unbind interfaces for the MC-bus can be consulted at +*Documentation/ABI/testing/sysfs-bus-fsl-mc*. + +DPRC driver +----------- +The DPRC driver is bound to DPRC objects and does runtime management +of a bus instance. It performs the initial bus scan of the DPRC +and handles interrupts for container events such as hot plug by +re-scanning the DPRC. + +Allocator +--------- +Certain objects such as DPMCP and DPBP are generic and fungible, +and are intended to be used by other drivers. For example, +the DPAA2 Ethernet driver needs: + +- DPMCPs to send MC commands, to configure network interfaces +- DPBPs for network buffer pools + +The allocator driver registers for these allocatable object types +and those objects are bound to the allocator when the bus is probed. +The allocator maintains a pool of objects that are available for +allocation by other DPAA2 drivers. + +DPIO driver +----------- +The DPIO driver is bound to DPIO objects and provides services that allow +other drivers such as the Ethernet driver to enqueue and dequeue data for +their respective objects. +Key services include: + +- data availability notifications +- hardware queuing operations (enqueue and dequeue of data) +- hardware buffer pool management + +To transmit a packet the Ethernet driver puts data on a queue and +invokes a DPIO API. For receive, the Ethernet driver registers +a data availability notification callback. To dequeue a packet +a DPIO API is used. +There is typically one DPIO object per physical CPU for optimum +performance, allowing different CPUs to simultaneously enqueue +and dequeue data. + +The DPIO driver operates on behalf of all DPAA2 drivers +active in the kernel-- Ethernet, crypto, compression, +etc. + +Ethernet driver +--------------- +The Ethernet driver is bound to a DPNI and implements the kernel +interfaces needed to connect the DPAA2 network interface to +the network stack. +Each DPNI corresponds to a Linux network interface. + +MAC driver +---------- +An Ethernet PHY is an off-chip, board specific component and is managed +by the appropriate PHY driver via an mdio bus. The MAC driver +plays a role of being a proxy between the PHY driver and the +MC. It does this proxy via the MC commands to a DPMAC object. +If the PHY driver signals a link change, the MAC driver notifies +the MC via a DPMAC command. If a network interface is brought +up or down, the MC notifies the DPMAC driver via an interrupt and +the driver can take appropriate action. diff --git a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/switch-driver.rst b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/switch-driver.rst new file mode 100644 index 0000000000..8bf411b857 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/switch-driver.rst @@ -0,0 +1,217 @@ +.. SPDX-License-Identifier: GPL-2.0 +.. include:: <isonum.txt> + +=================== +DPAA2 Switch driver +=================== + +:Copyright: |copy| 2021 NXP + +The DPAA2 Switch driver probes on the Datapath Switch (DPSW) object which can +be instantiated on the following DPAA2 SoCs and their variants: LS2088A and +LX2160A. + +The driver uses the switch device driver model and exposes each switch port as +a network interface, which can be included in a bridge or used as a standalone +interface. Traffic switched between ports is offloaded into the hardware. + +The DPSW can have ports connected to DPNIs or to DPMACs for external access. +:: + + [ethA] [ethB] [ethC] [ethD] [ethE] [ethF] + : : : : : : + : : : : : : + [dpaa2-eth] [dpaa2-eth] [ dpaa2-switch ] + : : : : : : kernel + ============================================================================= + : : : : : : hardware + [DPNI] [DPNI] [============= DPSW =================] + | | | | | | + | ---------- | [DPMAC] [DPMAC] + ------------------------------- | | + | | + [PHY] [PHY] + +Creating an Ethernet Switch +=========================== + +The dpaa2-switch driver probes on DPSW devices found on the fsl-mc bus. These +devices can be either created statically through the boot time configuration +file - DataPath Layout (DPL) - or at runtime using the DPAA2 object APIs +(incorporated already into the restool userspace tool). + +At the moment, the dpaa2-switch driver imposes the following restrictions on +the DPSW object that it will probe: + + * The minimum number of FDBs should be at least equal to the number of switch + interfaces. This is necessary so that separation of switch ports can be + done, ie when not under a bridge, each switch port will have its own FDB. + :: + + fsl_dpaa2_switch dpsw.0: The number of FDBs is lower than the number of ports, cannot probe + + * Both the broadcast and flooding configuration should be per FDB. This + enables the driver to restrict the broadcast and flooding domains of each + FDB depending on the switch ports that are sharing it (aka are under the + same bridge). + :: + + fsl_dpaa2_switch dpsw.0: Flooding domain is not per FDB, cannot probe + fsl_dpaa2_switch dpsw.0: Broadcast domain is not per FDB, cannot probe + + * The control interface of the switch should not be disabled + (DPSW_OPT_CTRL_IF_DIS not passed as a create time option). Without the + control interface, the driver is not capable to provide proper Rx/Tx traffic + support on the switch port netdevices. + :: + + fsl_dpaa2_switch dpsw.0: Control Interface is disabled, cannot probe + +Besides the configuration of the actual DPSW object, the dpaa2-switch driver +will need the following DPAA2 objects: + + * 1 DPMCP - A Management Command Portal object is needed for any interraction + with the MC firmware. + + * 1 DPBP - A Buffer Pool is used for seeding buffers intended for the Rx path + on the control interface. + + * Access to at least one DPIO object (Software Portal) is needed for any + enqueue/dequeue operation to be performed on the control interface queues. + The DPIO object will be shared, no need for a private one. + +Switching features +================== + +The driver supports the configuration of L2 forwarding rules in hardware for +port bridging as well as standalone usage of the independent switch interfaces. + +The hardware is not configurable with respect to VLAN awareness, thus any DPAA2 +switch port should be used only in usecases with a VLAN aware bridge:: + + $ ip link add dev br0 type bridge vlan_filtering 1 + + $ ip link add dev br1 type bridge + $ ip link set dev ethX master br1 + Error: fsl_dpaa2_switch: Cannot join a VLAN-unaware bridge + +Topology and loop detection through STP is supported when ``stp_state 1`` is +used at bridge create :: + + $ ip link add dev br0 type bridge vlan_filtering 1 stp_state 1 + +L2 FDB manipulation (add/delete/dump) is supported. + +HW FDB learning can be configured on each switch port independently through +bridge commands. When the HW learning is disabled, a fast age procedure will be +run and any previously learnt addresses will be removed. +:: + + $ bridge link set dev ethX learning off + $ bridge link set dev ethX learning on + +Restricting the unknown unicast and multicast flooding domain is supported, but +not independently of each other:: + + $ ip link set dev ethX type bridge_slave flood off mcast_flood off + $ ip link set dev ethX type bridge_slave flood off mcast_flood on + Error: fsl_dpaa2_switch: Cannot configure multicast flooding independently of unicast. + +Broadcast flooding on a switch port can be disabled/enabled through the brport sysfs:: + + $ echo 0 > /sys/bus/fsl-mc/devices/dpsw.Y/net/ethX/brport/broadcast_flood + +Offloads +======== + +Routing actions (redirect, trap, drop) +-------------------------------------- + +The DPAA2 switch is able to offload flow-based redirection of packets making +use of ACL tables. Shared filter blocks are supported by sharing a single ACL +table between multiple ports. + +The following flow keys are supported: + + * Ethernet: dst_mac/src_mac + * IPv4: dst_ip/src_ip/ip_proto/tos + * VLAN: vlan_id/vlan_prio/vlan_tpid/vlan_dei + * L4: dst_port/src_port + +Also, the matchall filter can be used to redirect the entire traffic received +on a port. + +As per flow actions, the following are supported: + + * drop + * mirred egress redirect + * trap + +Each ACL entry (filter) can be setup with only one of the listed +actions. + +Example 1: send frames received on eth4 with a SA of 00:01:02:03:04:05 to the +CPU:: + + $ tc qdisc add dev eth4 clsact + $ tc filter add dev eth4 ingress flower src_mac 00:01:02:03:04:05 skip_sw action trap + +Example 2: drop frames received on eth4 with VID 100 and PCP of 3:: + + $ tc filter add dev eth4 ingress protocol 802.1q flower skip_sw vlan_id 100 vlan_prio 3 action drop + +Example 3: redirect all frames received on eth4 to eth1:: + + $ tc filter add dev eth4 ingress matchall action mirred egress redirect dev eth1 + +Example 4: Use a single shared filter block on both eth5 and eth6:: + + $ tc qdisc add dev eth5 ingress_block 1 clsact + $ tc qdisc add dev eth6 ingress_block 1 clsact + $ tc filter add block 1 ingress flower dst_mac 00:01:02:03:04:04 skip_sw \ + action trap + $ tc filter add block 1 ingress protocol ipv4 flower src_ip 192.168.1.1 skip_sw \ + action mirred egress redirect dev eth3 + +Mirroring +~~~~~~~~~ + +The DPAA2 switch supports only per port mirroring and per VLAN mirroring. +Adding mirroring filters in shared blocks is also supported. + +When using the tc-flower classifier with the 802.1q protocol, only the +''vlan_id'' key will be accepted. Mirroring based on any other fields from the +802.1q protocol will be rejected:: + + $ tc qdisc add dev eth8 ingress_block 1 clsact + $ tc filter add block 1 ingress protocol 802.1q flower skip_sw vlan_prio 3 action mirred egress mirror dev eth6 + Error: fsl_dpaa2_switch: Only matching on VLAN ID supported. + We have an error talking to the kernel + +If a mirroring VLAN filter is requested on a port, the VLAN must to be +installed on the switch port in question either using ''bridge'' or by creating +a VLAN upper device if the switch port is used as a standalone interface:: + + $ tc qdisc add dev eth8 ingress_block 1 clsact + $ tc filter add block 1 ingress protocol 802.1q flower skip_sw vlan_id 200 action mirred egress mirror dev eth6 + Error: VLAN must be installed on the switch port. + We have an error talking to the kernel + + $ bridge vlan add vid 200 dev eth8 + $ tc filter add block 1 ingress protocol 802.1q flower skip_sw vlan_id 200 action mirred egress mirror dev eth6 + + $ ip link add link eth8 name eth8.200 type vlan id 200 + $ tc filter add block 1 ingress protocol 802.1q flower skip_sw vlan_id 200 action mirred egress mirror dev eth6 + +Also, it should be noted that the mirrored traffic will be subject to the same +egress restrictions as any other traffic. This means that when a mirrored +packet will reach the mirror port, if the VLAN found in the packet is not +installed on the port it will get dropped. + +The DPAA2 switch supports only a single mirroring destination, thus multiple +mirror rules can be installed but their ''to'' port has to be the same:: + + $ tc filter add block 1 ingress protocol 802.1q flower skip_sw vlan_id 200 action mirred egress mirror dev eth6 + $ tc filter add block 1 ingress protocol 802.1q flower skip_sw vlan_id 100 action mirred egress mirror dev eth7 + Error: fsl_dpaa2_switch: Multiple mirror ports not supported. + We have an error talking to the kernel diff --git a/Documentation/networking/device_drivers/ethernet/freescale/gianfar.rst b/Documentation/networking/device_drivers/ethernet/freescale/gianfar.rst new file mode 100644 index 0000000000..9c4a91d382 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/freescale/gianfar.rst @@ -0,0 +1,51 @@ +.. SPDX-License-Identifier: GPL-2.0 + +=========================== +The Gianfar Ethernet Driver +=========================== + +:Author: Andy Fleming <afleming@freescale.com> +:Updated: 2005-07-28 + + +Checksum Offloading +=================== + +The eTSEC controller (first included in parts from late 2005 like +the 8548) has the ability to perform TCP, UDP, and IP checksums +in hardware. The Linux kernel only offloads the TCP and UDP +checksums (and always performs the pseudo header checksums), so +the driver only supports checksumming for TCP/IP and UDP/IP +packets. Use ethtool to enable or disable this feature for RX +and TX. + +VLAN +==== + +In order to use VLAN, please consult Linux documentation on +configuring VLANs. The gianfar driver supports hardware insertion and +extraction of VLAN headers, but not filtering. Filtering will be +done by the kernel. + +Multicasting +============ + +The gianfar driver supports using the group hash table on the +TSEC (and the extended hash table on the eTSEC) for multicast +filtering. On the eTSEC, the exact-match MAC registers are used +before the hash tables. See Linux documentation on how to join +multicast groups. + +Padding +======= + +The gianfar driver supports padding received frames with 2 bytes +to align the IP header to a 16-byte boundary, when supported by +hardware. + +Ethtool +======= + +The gianfar driver supports the use of ethtool for many +configuration options. You must run ethtool only on currently +open interfaces. See ethtool documentation for details. diff --git a/Documentation/networking/device_drivers/ethernet/google/gve.rst b/Documentation/networking/device_drivers/ethernet/google/gve.rst new file mode 100644 index 0000000000..31d621bca8 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/google/gve.rst @@ -0,0 +1,175 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +============================================================== +Linux kernel driver for Compute Engine Virtual Ethernet (gve): +============================================================== + +Supported Hardware +=================== +The GVE driver binds to a single PCI device id used by the virtual +Ethernet device found in some Compute Engine VMs. + ++--------------+----------+---------+ +|Field | Value | Comments| ++==============+==========+=========+ +|Vendor ID | `0x1AE0` | Google | ++--------------+----------+---------+ +|Device ID | `0x0042` | | ++--------------+----------+---------+ +|Sub-vendor ID | `0x1AE0` | Google | ++--------------+----------+---------+ +|Sub-device ID | `0x0058` | | ++--------------+----------+---------+ +|Revision ID | `0x0` | | ++--------------+----------+---------+ +|Device Class | `0x200` | Ethernet| ++--------------+----------+---------+ + +PCI Bars +======== +The gVNIC PCI device exposes three 32-bit memory BARS: +- Bar0 - Device configuration and status registers. +- Bar1 - MSI-X vector table +- Bar2 - IRQ, RX and TX doorbells + +Device Interactions +=================== +The driver interacts with the device in the following ways: + - Registers + - A block of MMIO registers + - See gve_register.h for more detail + - Admin Queue + - See description below + - Reset + - At any time the device can be reset + - Interrupts + - See supported interrupts below + - Transmit and Receive Queues + - See description below + +Descriptor Formats +------------------ +GVE supports two descriptor formats: GQI and DQO. These two formats have +entirely different descriptors, which will be described below. + +Addressing Mode +------------------ +GVE supports two addressing modes: QPL and RDA. +QPL ("queue-page-list") mode communicates data through a set of +pre-registered pages. + +For RDA ("raw DMA addressing") mode, the set of pages is dynamic. +Therefore, the packet buffers can be anywhere in guest memory. + +Registers +--------- +All registers are MMIO. + +The registers are used for initializing and configuring the device as well as +querying device status in response to management interrupts. + +Endianness +---------- +- Admin Queue messages and registers are all Big Endian. +- GQI descriptors and datapath registers are Big Endian. +- DQO descriptors and datapath registers are Little Endian. + +Admin Queue (AQ) +---------------- +The Admin Queue is a PAGE_SIZE memory block, treated as an array of AQ +commands, used by the driver to issue commands to the device and set up +resources.The driver and the device maintain a count of how many commands +have been submitted and executed. To issue AQ commands, the driver must do +the following (with proper locking): + +1) Copy new commands into next available slots in the AQ array +2) Increment its counter by he number of new commands +3) Write the counter into the GVE_ADMIN_QUEUE_DOORBELL register +4) Poll the ADMIN_QUEUE_EVENT_COUNTER register until it equals + the value written to the doorbell, or until a timeout. + +The device will update the status field in each AQ command reported as +executed through the ADMIN_QUEUE_EVENT_COUNTER register. + +Device Resets +------------- +A device reset is triggered by writing 0x0 to the AQ PFN register. +This causes the device to release all resources allocated by the +driver, including the AQ itself. + +Interrupts +---------- +The following interrupts are supported by the driver: + +Management Interrupt +~~~~~~~~~~~~~~~~~~~~ +The management interrupt is used by the device to tell the driver to +look at the GVE_DEVICE_STATUS register. + +The handler for the management irq simply queues the service task in +the workqueue to check the register and acks the irq. + +Notification Block Interrupts +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +The notification block interrupts are used to tell the driver to poll +the queues associated with that interrupt. + +The handler for these irqs schedule the napi for that block to run +and poll the queues. + +GQI Traffic Queues +------------------ +GQI queues are composed of a descriptor ring and a buffer and are assigned to a +notification block. + +The descriptor rings are power-of-two-sized ring buffers consisting of +fixed-size descriptors. They advance their head pointer using a __be32 +doorbell located in Bar2. The tail pointers are advanced by consuming +descriptors in-order and updating a __be32 counter. Both the doorbell +and the counter overflow to zero. + +Each queue's buffers must be registered in advance with the device as a +queue page list, and packet data can only be put in those pages. + +Transmit +~~~~~~~~ +gve maps the buffers for transmit rings into a FIFO and copies the packets +into the FIFO before sending them to the NIC. + +Receive +~~~~~~~ +The buffers for receive rings are put into a data ring that is the same +length as the descriptor ring and the head and tail pointers advance over +the rings together. + +DQO Traffic Queues +------------------ +- Every TX and RX queue is assigned a notification block. + +- TX and RX buffers queues, which send descriptors to the device, use MMIO + doorbells to notify the device of new descriptors. + +- RX and TX completion queues, which receive descriptors from the device, use a + "generation bit" to know when a descriptor was populated by the device. The + driver initializes all bits with the "current generation". The device will + populate received descriptors with the "next generation" which is inverted + from the current generation. When the ring wraps, the current/next generation + are swapped. + +- It's the driver's responsibility to ensure that the RX and TX completion + queues are not overrun. This can be accomplished by limiting the number of + descriptors posted to HW. + +- TX packets have a 16 bit completion_tag and RX buffers have a 16 bit + buffer_id. These will be returned on the TX completion and RX queues + respectively to let the driver know which packet/buffer was completed. + +Transmit +~~~~~~~~ +A packet's buffers are DMA mapped for the device to access before transmission. +After the packet was successfully transmitted, the buffers are unmapped. + +Receive +~~~~~~~ +The driver posts fixed sized buffers to HW on the RX buffer queue. The packet +received on the associated RX queue may span multiple descriptors. diff --git a/Documentation/networking/device_drivers/ethernet/huawei/hinic.rst b/Documentation/networking/device_drivers/ethernet/huawei/hinic.rst new file mode 100644 index 0000000000..867ac8f4e0 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/huawei/hinic.rst @@ -0,0 +1,128 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============================================================ +Linux Kernel Driver for Huawei Intelligent NIC(HiNIC) family +============================================================ + +Overview: +========= +HiNIC is a network interface card for the Data Center Area. + +The driver supports a range of link-speed devices (10GbE, 25GbE, 40GbE, etc.). +The driver supports also a negotiated and extendable feature set. + +Some HiNIC devices support SR-IOV. This driver is used for Physical Function +(PF). + +HiNIC devices support MSI-X interrupt vector for each Tx/Rx queue and +adaptive interrupt moderation. + +HiNIC devices support also various offload features such as checksum offload, +TCP Transmit Segmentation Offload(TSO), Receive-Side Scaling(RSS) and +LRO(Large Receive Offload). + + +Supported PCI vendor ID/device IDs: +=================================== + +19e5:1822 - HiNIC PF + + +Driver Architecture and Source Code: +==================================== + +hinic_dev - Implement a Logical Network device that is independent from +specific HW details about HW data structure formats. + +hinic_hwdev - Implement the HW details of the device and include the components +for accessing the PCI NIC. + +hinic_hwdev contains the following components: +=============================================== + +HW Interface: +============= + +The interface for accessing the pci device (DMA memory and PCI BARs). +(hinic_hw_if.c, hinic_hw_if.h) + +Configuration Status Registers Area that describes the HW Registers on the +configuration and status BAR0. (hinic_hw_csr.h) + +MGMT components: +================ + +Asynchronous Event Queues(AEQs) - The event queues for receiving messages from +the MGMT modules on the cards. (hinic_hw_eqs.c, hinic_hw_eqs.h) + +Application Programmable Interface commands(API CMD) - Interface for sending +MGMT commands to the card. (hinic_hw_api_cmd.c, hinic_hw_api_cmd.h) + +Management (MGMT) - the PF to MGMT channel that uses API CMD for sending MGMT +commands to the card and receives notifications from the MGMT modules on the +card by AEQs. Also set the addresses of the IO CMDQs in HW. +(hinic_hw_mgmt.c, hinic_hw_mgmt.h) + +IO components: +============== + +Completion Event Queues(CEQs) - The completion Event Queues that describe IO +tasks that are finished. (hinic_hw_eqs.c, hinic_hw_eqs.h) + +Work Queues(WQ) - Contain the memory and operations for use by CMD queues and +the Queue Pairs. The WQ is a Memory Block in a Page. The Block contains +pointers to Memory Areas that are the Memory for the Work Queue Elements(WQEs). +(hinic_hw_wq.c, hinic_hw_wq.h) + +Command Queues(CMDQ) - The queues for sending commands for IO management and is +used to set the QPs addresses in HW. The commands completion events are +accumulated on the CEQ that is configured to receive the CMDQ completion events. +(hinic_hw_cmdq.c, hinic_hw_cmdq.h) + +Queue Pairs(QPs) - The HW Receive and Send queues for Receiving and Transmitting +Data. (hinic_hw_qp.c, hinic_hw_qp.h, hinic_hw_qp_ctxt.h) + +IO - de/constructs all the IO components. (hinic_hw_io.c, hinic_hw_io.h) + +HW device: +========== + +HW device - de/constructs the HW Interface, the MGMT components on the +initialization of the driver and the IO components on the case of Interface +UP/DOWN Events. (hinic_hw_dev.c, hinic_hw_dev.h) + + +hinic_dev contains the following components: +=============================================== + +PCI ID table - Contains the supported PCI Vendor/Device IDs. +(hinic_pci_tbl.h) + +Port Commands - Send commands to the HW device for port management +(MAC, Vlan, MTU, ...). (hinic_port.c, hinic_port.h) + +Tx Queues - Logical Tx Queues that use the HW Send Queues for transmit. +The Logical Tx queue is not dependent on the format of the HW Send Queue. +(hinic_tx.c, hinic_tx.h) + +Rx Queues - Logical Rx Queues that use the HW Receive Queues for receive. +The Logical Rx queue is not dependent on the format of the HW Receive Queue. +(hinic_rx.c, hinic_rx.h) + +hinic_dev - de/constructs the Logical Tx and Rx Queues. +(hinic_main.c, hinic_dev.h) + + +Miscellaneous +============= + +Common functions that are used by HW and Logical Device. +(hinic_common.c, hinic_common.h) + + +Support +======= + +If an issue is identified with the released source code on the supported kernel +with a supported adapter, email the specific information related to the issue to +aviad.krawczyk@huawei.com. diff --git a/Documentation/networking/device_drivers/ethernet/index.rst b/Documentation/networking/device_drivers/ethernet/index.rst new file mode 100644 index 0000000000..9827e81608 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/index.rst @@ -0,0 +1,64 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) + +Ethernet Device Drivers +======================= + +Device drivers for Ethernet and Ethernet-based virtual function devices. + +Contents: + +.. toctree:: + :maxdepth: 2 + + 3com/3c509 + 3com/vortex + amazon/ena + altera/altera_tse + amd/pds_core + amd/pds_vdpa + amd/pds_vfio_pci + aquantia/atlantic + chelsio/cxgb + cirrus/cs89x0 + dlink/dl2k + davicom/dm9000 + dec/dmfe + freescale/dpaa + freescale/dpaa2/index + freescale/gianfar + google/gve + huawei/hinic + intel/e100 + intel/e1000 + intel/e1000e + intel/fm10k + intel/igb + intel/igbvf + intel/ixgbe + intel/ixgbevf + intel/i40e + intel/iavf + intel/ice + marvell/octeontx2 + marvell/octeon_ep + mellanox/mlx5/index + microsoft/netvsc + neterion/s2io + netronome/nfp + pensando/ionic + smsc/smc9 + stmicro/stmmac + ti/cpsw + ti/cpsw_switchdev + ti/am65_nuss_cpsw_switchdev + ti/tlan + toshiba/spider_net + wangxun/txgbe + wangxun/ngbe + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/ethernet/intel/e100.rst b/Documentation/networking/device_drivers/ethernet/intel/e100.rst new file mode 100644 index 0000000000..5dee1b53e9 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/intel/e100.rst @@ -0,0 +1,185 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +============================================================= +Linux Base Driver for the Intel(R) PRO/100 Family of Adapters +============================================================= + +June 1, 2018 + +Contents +======== + +- In This Release +- Identifying Your Adapter +- Building and Installation +- Driver Configuration Parameters +- Additional Configurations +- Known Issues +- Support + + +In This Release +=============== + +This file describes the Linux Base Driver for the Intel(R) PRO/100 Family of +Adapters. This driver includes support for Itanium(R)2-based systems. + +For questions related to hardware requirements, refer to the documentation +supplied with your Intel PRO/100 adapter. + +The following features are now available in supported kernels: + - Native VLANs + - Channel Bonding (teaming) + - SNMP + +Channel Bonding documentation can be found in the Linux kernel source: +/Documentation/networking/bonding.rst + + +Identifying Your Adapter +======================== + +For information on how to identify your adapter, and for the latest Intel +network drivers, refer to the Intel Support website: +https://www.intel.com/support + +Driver Configuration Parameters +=============================== + +The default value for each parameter is generally the recommended setting, +unless otherwise noted. + +Rx Descriptors: + Number of receive descriptors. A receive descriptor is a data + structure that describes a receive buffer and its attributes to the network + controller. The data in the descriptor is used by the controller to write + data from the controller to host memory. In the 3.x.x driver the valid range + for this parameter is 64-256. The default value is 256. This parameter can be + changed using the command:: + + ethtool -G eth? rx n + + Where n is the number of desired Rx descriptors. + +Tx Descriptors: + Number of transmit descriptors. A transmit descriptor is a data + structure that describes a transmit buffer and its attributes to the network + controller. The data in the descriptor is used by the controller to read + data from the host memory to the controller. In the 3.x.x driver the valid + range for this parameter is 64-256. The default value is 128. This parameter + can be changed using the command:: + + ethtool -G eth? tx n + + Where n is the number of desired Tx descriptors. + +Speed/Duplex: + The driver auto-negotiates the link speed and duplex settings by + default. The ethtool utility can be used as follows to force speed/duplex.:: + + ethtool -s eth? autoneg off speed {10|100} duplex {full|half} + + NOTE: setting the speed/duplex to incorrect values will cause the link to + fail. + +Event Log Message Level: + The driver uses the message level flag to log events + to syslog. The message level can be set at driver load time. It can also be + set using the command:: + + ethtool -s eth? msglvl n + + +Additional Configurations +========================= + +Configuring the Driver on Different Distributions +------------------------------------------------- + +Configuring a network driver to load properly when the system is started +is distribution dependent. Typically, the configuration process involves +adding an alias line to `/etc/modprobe.d/*.conf` as well as editing other +system startup scripts and/or configuration files. Many popular Linux +distributions ship with tools to make these changes for you. To learn +the proper way to configure a network device for your system, refer to +your distribution documentation. If during this process you are asked +for the driver or module name, the name for the Linux Base Driver for +the Intel PRO/100 Family of Adapters is e100. + +As an example, if you install the e100 driver for two PRO/100 adapters +(eth0 and eth1), add the following to a configuration file in +/etc/modprobe.d/:: + + alias eth0 e100 + alias eth1 e100 + +Viewing Link Messages +--------------------- + +In order to see link messages and other Intel driver information on your +console, you must set the dmesg level up to six. This can be done by +entering the following on the command line before loading the e100 +driver:: + + dmesg -n 6 + +If you wish to see all messages issued by the driver, including debug +messages, set the dmesg level to eight. + +NOTE: This setting is not saved across reboots. + +ethtool +------- + +The driver utilizes the ethtool interface for driver configuration and +diagnostics, as well as displaying statistical information. The ethtool +version 1.6 or later is required for this functionality. + +The latest release of ethtool can be found from +https://www.kernel.org/pub/software/network/ethtool/ + +Enabling Wake on LAN (WoL) +-------------------------- +WoL is provided through the ethtool utility. For instructions on +enabling WoL with ethtool, refer to the ethtool man page. WoL will be +enabled on the system during the next shut down or reboot. For this +driver version, in order to enable WoL, the e100 driver must be loaded +when shutting down or rebooting the system. + +NAPI +---- + +NAPI (Rx polling mode) is supported in the e100 driver. + +See :ref:`Documentation/networking/napi.rst <napi>` for more information. + +Multiple Interfaces on Same Ethernet Broadcast Network +------------------------------------------------------ + +Due to the default ARP behavior on Linux, it is not possible to have one +system on two IP networks in the same Ethernet broadcast domain +(non-partitioned switch) behave as expected. All Ethernet interfaces +will respond to IP traffic for any IP address assigned to the system. +This results in unbalanced receive traffic. + +If you have multiple interfaces in a server, either turn on ARP +filtering by + +(1) entering:: + + echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter + + (this only works if your kernel's version is higher than 2.4.5), or + +(2) installing the interfaces in separate broadcast domains (either + in different switches or in a switch partitioned to VLANs). + + +Support +======= +For general information, go to the Intel support website at: +https://www.intel.com/support/ + +If an issue is identified with the released source code on a supported kernel +with a supported adapter, email the specific information related to the issue +to intel-wired-lan@lists.osuosl.org. diff --git a/Documentation/networking/device_drivers/ethernet/intel/e1000.rst b/Documentation/networking/device_drivers/ethernet/intel/e1000.rst new file mode 100644 index 0000000000..52a7fb9ce8 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/intel/e1000.rst @@ -0,0 +1,458 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +========================================================== +Linux Base Driver for Intel(R) Ethernet Network Connection +========================================================== + +Intel Gigabit Linux driver. +Copyright(c) 1999 - 2013 Intel Corporation. + +Contents +======== + +- Identifying Your Adapter +- Command Line Parameters +- Speed and Duplex Configuration +- Additional Configurations +- Support + +Identifying Your Adapter +======================== + +For more information on how to identify your adapter, go to the Adapter & +Driver ID Guide at: + + http://support.intel.com/support/go/network/adapter/idguide.htm + +For the latest Intel network drivers for Linux, refer to the following +website. In the search field, enter your adapter name or type, or use the +networking link on the left to search for your adapter: + + http://support.intel.com/support/go/network/adapter/home.htm + +Command Line Parameters +======================= + +The default value for each parameter is generally the recommended setting, +unless otherwise noted. + +NOTES: + For more information about the AutoNeg, Duplex, and Speed + parameters, see the "Speed and Duplex Configuration" section in + this document. + + For more information about the InterruptThrottleRate, + RxIntDelay, TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay + parameters, see the application note at: + http://www.intel.com/design/network/applnots/ap450.htm + +AutoNeg +------- + +(Supported only on adapters with copper connections) + +:Valid Range: 0x01-0x0F, 0x20-0x2F +:Default Value: 0x2F + +This parameter is a bit-mask that specifies the speed and duplex settings +advertised by the adapter. When this parameter is used, the Speed and +Duplex parameters must not be specified. + +NOTE: + Refer to the Speed and Duplex section of this readme for more + information on the AutoNeg parameter. + +Duplex +------ + +(Supported only on adapters with copper connections) + +:Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full) +:Default Value: 0 + +This defines the direction in which data is allowed to flow. Can be +either one or two-directional. If both Duplex and the link partner are +set to auto-negotiate, the board auto-detects the correct duplex. If the +link partner is forced (either full or half), Duplex defaults to half- +duplex. + +FlowControl +----------- + +:Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx) +:Default Value: Reads flow control settings from the EEPROM + +This parameter controls the automatic generation(Tx) and response(Rx) +to Ethernet PAUSE frames. + +InterruptThrottleRate +--------------------- + +(not supported on Intel(R) 82542, 82543 or 82544-based adapters) + +:Valid Range: + 0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative, + 4=simplified balancing) +:Default Value: 3 + +The driver can limit the amount of interrupts per second that the adapter +will generate for incoming packets. It does this by writing a value to the +adapter that is based on the maximum amount of interrupts that the adapter +will generate per second. + +Setting InterruptThrottleRate to a value greater or equal to 100 +will program the adapter to send out a maximum of that many interrupts +per second, even if more packets have come in. This reduces interrupt +load on the system and can lower CPU utilization under heavy load, +but will increase latency as packets are not processed as quickly. + +The default behaviour of the driver previously assumed a static +InterruptThrottleRate value of 8000, providing a good fallback value for +all traffic types,but lacking in small packet performance and latency. +The hardware can handle many more small packets per second however, and +for this reason an adaptive interrupt moderation algorithm was implemented. + +Since 7.3.x, the driver has two adaptive modes (setting 1 or 3) in which +it dynamically adjusts the InterruptThrottleRate value based on the traffic +that it receives. After determining the type of incoming traffic in the last +timeframe, it will adjust the InterruptThrottleRate to an appropriate value +for that traffic. + +The algorithm classifies the incoming traffic every interval into +classes. Once the class is determined, the InterruptThrottleRate value is +adjusted to suit that traffic type the best. There are three classes defined: +"Bulk traffic", for large amounts of packets of normal size; "Low latency", +for small amounts of traffic and/or a significant percentage of small +packets; and "Lowest latency", for almost completely small packets or +minimal traffic. + +In dynamic conservative mode, the InterruptThrottleRate value is set to 4000 +for traffic that falls in class "Bulk traffic". If traffic falls in the "Low +latency" or "Lowest latency" class, the InterruptThrottleRate is increased +stepwise to 20000. This default mode is suitable for most applications. + +For situations where low latency is vital such as cluster or +grid computing, the algorithm can reduce latency even more when +InterruptThrottleRate is set to mode 1. In this mode, which operates +the same as mode 3, the InterruptThrottleRate will be increased stepwise to +70000 for traffic in class "Lowest latency". + +In simplified mode the interrupt rate is based on the ratio of TX and +RX traffic. If the bytes per second rate is approximately equal, the +interrupt rate will drop as low as 2000 interrupts per second. If the +traffic is mostly transmit or mostly receive, the interrupt rate could +be as high as 8000. + +Setting InterruptThrottleRate to 0 turns off any interrupt moderation +and may improve small packet latency, but is generally not suitable +for bulk throughput traffic. + +NOTE: + InterruptThrottleRate takes precedence over the TxAbsIntDelay and + RxAbsIntDelay parameters. In other words, minimizing the receive + and/or transmit absolute delays does not force the controller to + generate more interrupts than what the Interrupt Throttle Rate + allows. + +CAUTION: + If you are using the Intel(R) PRO/1000 CT Network Connection + (controller 82547), setting InterruptThrottleRate to a value + greater than 75,000, may hang (stop transmitting) adapters + under certain network conditions. If this occurs a NETDEV + WATCHDOG message is logged in the system event log. In + addition, the controller is automatically reset, restoring + the network connection. To eliminate the potential for the + hang, ensure that InterruptThrottleRate is set no greater + than 75,000 and is not set to 0. + +NOTE: + When e1000 is loaded with default settings and multiple adapters + are in use simultaneously, the CPU utilization may increase non- + linearly. In order to limit the CPU utilization without impacting + the overall throughput, we recommend that you load the driver as + follows:: + + modprobe e1000 InterruptThrottleRate=3000,3000,3000 + + This sets the InterruptThrottleRate to 3000 interrupts/sec for + the first, second, and third instances of the driver. The range + of 2000 to 3000 interrupts per second works on a majority of + systems and is a good starting point, but the optimal value will + be platform-specific. If CPU utilization is not a concern, use + RX_POLLING (NAPI) and default driver settings. + +RxDescriptors +------------- + +:Valid Range: + - 48-256 for 82542 and 82543-based adapters + - 48-4096 for all other supported adapters +:Default Value: 256 + +This value specifies the number of receive buffer descriptors allocated +by the driver. Increasing this value allows the driver to buffer more +incoming packets, at the expense of increased system memory utilization. + +Each descriptor is 16 bytes. A receive buffer is also allocated for each +descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending +on the MTU setting. The maximum MTU size is 16110. + +NOTE: + MTU designates the frame size. It only needs to be set for Jumbo + Frames. Depending on the available system resources, the request + for a higher number of receive descriptors may be denied. In this + case, use a lower number. + +RxIntDelay +---------- + +:Valid Range: 0-65535 (0=off) +:Default Value: 0 + +This value delays the generation of receive interrupts in units of 1.024 +microseconds. Receive interrupt reduction can improve CPU efficiency if +properly tuned for specific network traffic. Increasing this value adds +extra latency to frame reception and can end up decreasing the throughput +of TCP traffic. If the system is reporting dropped receives, this value +may be set too high, causing the driver to run out of available receive +descriptors. + +CAUTION: + When setting RxIntDelay to a value other than 0, adapters may + hang (stop transmitting) under certain network conditions. If + this occurs a NETDEV WATCHDOG message is logged in the system + event log. In addition, the controller is automatically reset, + restoring the network connection. To eliminate the potential + for the hang ensure that RxIntDelay is set to 0. + +RxAbsIntDelay +------------- + +(This parameter is supported only on 82540, 82545 and later adapters.) + +:Valid Range: 0-65535 (0=off) +:Default Value: 128 + +This value, in units of 1.024 microseconds, limits the delay in which a +receive interrupt is generated. Useful only if RxIntDelay is non-zero, +this value ensures that an interrupt is generated after the initial +packet is received within the set amount of time. Proper tuning, +along with RxIntDelay, may improve traffic throughput in specific network +conditions. + +Speed +----- + +(This parameter is supported only on adapters with copper connections.) + +:Valid Settings: 0, 10, 100, 1000 +:Default Value: 0 (auto-negotiate at all supported speeds) + +Speed forces the line speed to the specified value in megabits per second +(Mbps). If this parameter is not specified or is set to 0 and the link +partner is set to auto-negotiate, the board will auto-detect the correct +speed. Duplex should also be set when Speed is set to either 10 or 100. + +TxDescriptors +------------- + +:Valid Range: + - 48-256 for 82542 and 82543-based adapters + - 48-4096 for all other supported adapters +:Default Value: 256 + +This value is the number of transmit descriptors allocated by the driver. +Increasing this value allows the driver to queue more transmits. Each +descriptor is 16 bytes. + +NOTE: + Depending on the available system resources, the request for a + higher number of transmit descriptors may be denied. In this case, + use a lower number. + +TxIntDelay +---------- + +:Valid Range: 0-65535 (0=off) +:Default Value: 8 + +This value delays the generation of transmit interrupts in units of +1.024 microseconds. Transmit interrupt reduction can improve CPU +efficiency if properly tuned for specific network traffic. If the +system is reporting dropped transmits, this value may be set too high +causing the driver to run out of available transmit descriptors. + +TxAbsIntDelay +------------- + +(This parameter is supported only on 82540, 82545 and later adapters.) + +:Valid Range: 0-65535 (0=off) +:Default Value: 32 + +This value, in units of 1.024 microseconds, limits the delay in which a +transmit interrupt is generated. Useful only if TxIntDelay is non-zero, +this value ensures that an interrupt is generated after the initial +packet is sent on the wire within the set amount of time. Proper tuning, +along with TxIntDelay, may improve traffic throughput in specific +network conditions. + +XsumRX +------ + +(This parameter is NOT supported on the 82542-based adapter.) + +:Valid Range: 0-1 +:Default Value: 1 + +A value of '1' indicates that the driver should enable IP checksum +offload for received packets (both UDP and TCP) to the adapter hardware. + +Copybreak +--------- + +:Valid Range: 0-xxxxxxx (0=off) +:Default Value: 256 +:Usage: modprobe e1000.ko copybreak=128 + +Driver copies all packets below or equaling this size to a fresh RX +buffer before handing it up the stack. + +This parameter is different than other parameters, in that it is a +single (not 1,1,1 etc.) parameter applied to all driver instances and +it is also available during runtime at +/sys/module/e1000/parameters/copybreak + +SmartPowerDownEnable +-------------------- + +:Valid Range: 0-1 +:Default Value: 0 (disabled) + +Allows PHY to turn off in lower power states. The user can turn off +this parameter in supported chipsets. + +Speed and Duplex Configuration +============================== + +Three keywords are used to control the speed and duplex configuration. +These keywords are Speed, Duplex, and AutoNeg. + +If the board uses a fiber interface, these keywords are ignored, and the +fiber interface board only links at 1000 Mbps full-duplex. + +For copper-based boards, the keywords interact as follows: + +- The default operation is auto-negotiate. The board advertises all + supported speed and duplex combinations, and it links at the highest + common speed and duplex mode IF the link partner is set to auto-negotiate. + +- If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps + is advertised (The 1000BaseT spec requires auto-negotiation.) + +- If Speed = 10 or 100, then both Speed and Duplex should be set. Auto- + negotiation is disabled, and the AutoNeg parameter is ignored. Partner + SHOULD also be forced. + +The AutoNeg parameter is used when more control is required over the +auto-negotiation process. It should be used when you wish to control which +speed and duplex combinations are advertised during the auto-negotiation +process. + +The parameter may be specified as either a decimal or hexadecimal value as +determined by the bitmap below. + +============== ====== ====== ======= ======= ====== ====== ======= ====== +Bit position 7 6 5 4 3 2 1 0 +Decimal Value 128 64 32 16 8 4 2 1 +Hex value 80 40 20 10 8 4 2 1 +Speed (Mbps) N/A N/A 1000 N/A 100 100 10 10 +Duplex Full Full Half Full Half +============== ====== ====== ======= ======= ====== ====== ======= ====== + +Some examples of using AutoNeg:: + + modprobe e1000 AutoNeg=0x01 (Restricts autonegotiation to 10 Half) + modprobe e1000 AutoNeg=1 (Same as above) + modprobe e1000 AutoNeg=0x02 (Restricts autonegotiation to 10 Full) + modprobe e1000 AutoNeg=0x03 (Restricts autonegotiation to 10 Half or 10 Full) + modprobe e1000 AutoNeg=0x04 (Restricts autonegotiation to 100 Half) + modprobe e1000 AutoNeg=0x05 (Restricts autonegotiation to 10 Half or 100 + Half) + modprobe e1000 AutoNeg=0x020 (Restricts autonegotiation to 1000 Full) + modprobe e1000 AutoNeg=32 (Same as above) + +Note that when this parameter is used, Speed and Duplex must not be specified. + +If the link partner is forced to a specific speed and duplex, then this +parameter should not be used. Instead, use the Speed and Duplex parameters +previously mentioned to force the adapter to the same speed and duplex. + +Additional Configurations +========================= + +Jumbo Frames +------------ + + Jumbo Frames support is enabled by changing the MTU to a value larger than + the default of 1500. Use the ifconfig command to increase the MTU size. + For example:: + + ifconfig eth<x> mtu 9000 up + + This setting is not saved across reboots. It can be made permanent if + you add:: + + MTU=9000 + + to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>. This example + applies to the Red Hat distributions; other distributions may store this + setting in a different location. + +Notes: + Degradation in throughput performance may be observed in some Jumbo frames + environments. If this is observed, increasing the application's socket buffer + size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values may help. + See the specific application manual and /usr/src/linux*/Documentation/ + networking/ip-sysctl.txt for more details. + + - The maximum MTU setting for Jumbo Frames is 16110. This value coincides + with the maximum Jumbo Frames size of 16128. + + - Using Jumbo frames at 10 or 100 Mbps is not supported and may result in + poor performance or loss of link. + + - Adapters based on the Intel(R) 82542 and 82573V/E controller do not + support Jumbo Frames. These correspond to the following product names:: + + Intel(R) PRO/1000 Gigabit Server Adapter + Intel(R) PRO/1000 PM Network Connection + +ethtool +------- + + The driver utilizes the ethtool interface for driver configuration and + diagnostics, as well as displaying statistical information. The ethtool + version 1.6 or later is required for this functionality. + + The latest release of ethtool can be found from + https://www.kernel.org/pub/software/network/ethtool/ + +Enabling Wake on LAN (WoL) +-------------------------- + + WoL is configured through the ethtool utility. + + WoL will be enabled on the system during the next shut down or reboot. + For this driver version, in order to enable WoL, the e1000 driver must be + loaded when shutting down or rebooting the system. + +Support +======= + +For general information, go to the Intel support website at: +http://support.intel.com + +If an issue is identified with the released source code on the supported +kernel with a supported adapter, email the specific information related +to the issue to intel-wired-lan@lists.osuosl.org. diff --git a/Documentation/networking/device_drivers/ethernet/intel/e1000e.rst b/Documentation/networking/device_drivers/ethernet/intel/e1000e.rst new file mode 100644 index 0000000000..d8f810afdd --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/intel/e1000e.rst @@ -0,0 +1,378 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +===================================================== +Linux Driver for Intel(R) Ethernet Network Connection +===================================================== + +Intel Gigabit Linux driver. +Copyright(c) 2008-2018 Intel Corporation. + +Contents +======== + +- Identifying Your Adapter +- Command Line Parameters +- Additional Configurations +- Support + + +Identifying Your Adapter +======================== +For information on how to identify your adapter, and for the latest Intel +network drivers, refer to the Intel Support website: +https://www.intel.com/support + + +Command Line Parameters +======================= +If the driver is built as a module, the following optional parameters are used +by entering them on the command line with the modprobe command using this +syntax:: + + modprobe e1000e [<option>=<VAL1>,<VAL2>,...] + +There needs to be a <VAL#> for each network port in the system supported by +this driver. The values will be applied to each instance, in function order. +For example:: + + modprobe e1000e InterruptThrottleRate=16000,16000 + +In this case, there are two network ports supported by e1000e in the system. +The default value for each parameter is generally the recommended setting, +unless otherwise noted. + +NOTE: A descriptor describes a data buffer and attributes related to the data +buffer. This information is accessed by the hardware. + +InterruptThrottleRate +--------------------- +:Valid Range: 0,1,3,4,100-100000 +:Default Value: 3 + +Interrupt Throttle Rate controls the number of interrupts each interrupt +vector can generate per second. Increasing ITR lowers latency at the cost of +increased CPU utilization, though it may help throughput in some circumstances. + +Setting InterruptThrottleRate to a value greater or equal to 100 +will program the adapter to send out a maximum of that many interrupts +per second, even if more packets have come in. This reduces interrupt +load on the system and can lower CPU utilization under heavy load, +but will increase latency as packets are not processed as quickly. + +The default behaviour of the driver previously assumed a static +InterruptThrottleRate value of 8000, providing a good fallback value for +all traffic types, but lacking in small packet performance and latency. +The hardware can handle many more small packets per second however, and +for this reason an adaptive interrupt moderation algorithm was implemented. + +The driver has two adaptive modes (setting 1 or 3) in which +it dynamically adjusts the InterruptThrottleRate value based on the traffic +that it receives. After determining the type of incoming traffic in the last +timeframe, it will adjust the InterruptThrottleRate to an appropriate value +for that traffic. + +The algorithm classifies the incoming traffic every interval into +classes. Once the class is determined, the InterruptThrottleRate value is +adjusted to suit that traffic type the best. There are three classes defined: +"Bulk traffic", for large amounts of packets of normal size; "Low latency", +for small amounts of traffic and/or a significant percentage of small +packets; and "Lowest latency", for almost completely small packets or +minimal traffic. + + - 0: Off + Turns off any interrupt moderation and may improve small packet latency. + However, this is generally not suitable for bulk throughput traffic due + to the increased CPU utilization of the higher interrupt rate. + - 1: Dynamic mode + This mode attempts to moderate interrupts per vector while maintaining + very low latency. This can sometimes cause extra CPU utilization. If + planning on deploying e1000e in a latency sensitive environment, this + parameter should be considered. + - 3: Dynamic Conservative mode (default) + In dynamic conservative mode, the InterruptThrottleRate value is set to + 4000 for traffic that falls in class "Bulk traffic". If traffic falls in + the "Low latency" or "Lowest latency" class, the InterruptThrottleRate is + increased stepwise to 20000. This default mode is suitable for most + applications. + - 4: Simplified Balancing mode + In simplified mode the interrupt rate is based on the ratio of TX and + RX traffic. If the bytes per second rate is approximately equal, the + interrupt rate will drop as low as 2000 interrupts per second. If the + traffic is mostly transmit or mostly receive, the interrupt rate could + be as high as 8000. + - 100-100000: + Setting InterruptThrottleRate to a value greater or equal to 100 + will program the adapter to send at most that many interrupts per second, + even if more packets have come in. This reduces interrupt load on the + system and can lower CPU utilization under heavy load, but will increase + latency as packets are not processed as quickly. + +NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and +RxAbsIntDelay parameters. In other words, minimizing the receive and/or +transmit absolute delays does not force the controller to generate more +interrupts than what the Interrupt Throttle Rate allows. + +RxIntDelay +---------- +:Valid Range: 0-65535 (0=off) +:Default Value: 0 + +This value delays the generation of receive interrupts in units of 1.024 +microseconds. Receive interrupt reduction can improve CPU efficiency if +properly tuned for specific network traffic. Increasing this value adds extra +latency to frame reception and can end up decreasing the throughput of TCP +traffic. If the system is reporting dropped receives, this value may be set +too high, causing the driver to run out of available receive descriptors. + +CAUTION: When setting RxIntDelay to a value other than 0, adapters may hang +(stop transmitting) under certain network conditions. If this occurs a NETDEV +WATCHDOG message is logged in the system event log. In addition, the +controller is automatically reset, restoring the network connection. To +eliminate the potential for the hang ensure that RxIntDelay is set to 0. + +RxAbsIntDelay +------------- +:Valid Range: 0-65535 (0=off) +:Default Value: 8 + +This value, in units of 1.024 microseconds, limits the delay in which a +receive interrupt is generated. This value ensures that an interrupt is +generated after the initial packet is received within the set amount of time, +which is useful only if RxIntDelay is non-zero. Proper tuning, along with +RxIntDelay, may improve traffic throughput in specific network conditions. + +TxIntDelay +---------- +:Valid Range: 0-65535 (0=off) +:Default Value: 8 + +This value delays the generation of transmit interrupts in units of 1.024 +microseconds. Transmit interrupt reduction can improve CPU efficiency if +properly tuned for specific network traffic. If the system is reporting +dropped transmits, this value may be set too high causing the driver to run +out of available transmit descriptors. + +TxAbsIntDelay +------------- +:Valid Range: 0-65535 (0=off) +:Default Value: 32 + +This value, in units of 1.024 microseconds, limits the delay in which a +transmit interrupt is generated. It is useful only if TxIntDelay is non-zero. +It ensures that an interrupt is generated after the initial Packet is sent on +the wire within the set amount of time. Proper tuning, along with TxIntDelay, +may improve traffic throughput in specific network conditions. + +copybreak +--------- +:Valid Range: 0-xxxxxxx (0=off) +:Default Value: 256 + +The driver copies all packets below or equaling this size to a fresh receive +buffer before handing it up the stack. +This parameter differs from other parameters because it is a single (not 1,1,1 +etc.) parameter applied to all driver instances and it is also available +during runtime at /sys/module/e1000e/parameters/copybreak. + +To use copybreak, type:: + + modprobe e1000e.ko copybreak=128 + +SmartPowerDownEnable +-------------------- +:Valid Range: 0,1 +:Default Value: 0 (disabled) + +Allows the PHY to turn off in lower power states. The user can turn off this +parameter in supported chipsets. + +KumeranLockLoss +--------------- +:Valid Range: 0,1 +:Default Value: 1 (enabled) + +This workaround skips resetting the PHY at shutdown for the initial silicon +releases of ICH8 systems. + +IntMode +------- +:Valid Range: 0-2 +:Default Value: 0 + + +-------+----------------+ + | Value | Interrupt Mode | + +=======+================+ + | 0 | Legacy | + +-------+----------------+ + | 1 | MSI | + +-------+----------------+ + | 2 | MSI-X | + +-------+----------------+ + +IntMode allows load time control over the type of interrupt registered for by +the driver. MSI-X is required for multiple queue support, and some kernels and +combinations of kernel .config options will force a lower level of interrupt +support. + +This command will show different values for each type of interrupt:: + + cat /proc/interrupts + +CrcStripping +------------ +:Valid Range: 0,1 +:Default Value: 1 (enabled) + +Strip the CRC from received packets before sending up the network stack. If +you have a machine with a BMC enabled but cannot receive IPMI traffic after +loading or enabling the driver, try disabling this feature. + +WriteProtectNVM +--------------- +:Valid Range: 0,1 +:Default Value: 1 (enabled) + +If set to 1, configure the hardware to ignore all write/erase cycles to the +GbE region in the ICHx NVM (in order to prevent accidental corruption of the +NVM). This feature can be disabled by setting the parameter to 0 during initial +driver load. + +NOTE: The machine must be power cycled (full off/on) when enabling NVM writes +via setting the parameter to zero. Once the NVM has been locked (via the +parameter at 1 when the driver loads) it cannot be unlocked except via power +cycle. + +Debug +----- +:Valid Range: 0-16 (0=none,...,16=all) +:Default Value: 0 + +This parameter adjusts the level of debug messages displayed in the system logs. + + +Additional Features and Configurations +====================================== + +Jumbo Frames +------------ +Jumbo Frames support is enabled by changing the Maximum Transmission Unit (MTU) +to a value larger than the default value of 1500. + +Use the ifconfig command to increase the MTU size. For example, enter the +following where <x> is the interface number:: + + ifconfig eth<x> mtu 9000 up + +Alternatively, you can use the ip command as follows:: + + ip link set mtu 9000 dev eth<x> + ip link set up dev eth<x> + +This setting is not saved across reboots. The setting change can be made +permanent by adding 'MTU=9000' to the file: + +- For RHEL: /etc/sysconfig/network-scripts/ifcfg-eth<x> +- For SLES: /etc/sysconfig/network/<config_file> + +NOTE: The maximum MTU setting for Jumbo Frames is 8996. This value coincides +with the maximum Jumbo Frames size of 9018 bytes. + +NOTE: Using Jumbo frames at 10 or 100 Mbps is not supported and may result in +poor performance or loss of link. + +NOTE: The following adapters limit Jumbo Frames sized packets to a maximum of +4088 bytes: + + - Intel(R) 82578DM Gigabit Network Connection + - Intel(R) 82577LM Gigabit Network Connection + +The following adapters do not support Jumbo Frames: + + - Intel(R) PRO/1000 Gigabit Server Adapter + - Intel(R) PRO/1000 PM Network Connection + - Intel(R) 82562G 10/100 Network Connection + - Intel(R) 82562G-2 10/100 Network Connection + - Intel(R) 82562GT 10/100 Network Connection + - Intel(R) 82562GT-2 10/100 Network Connection + - Intel(R) 82562V 10/100 Network Connection + - Intel(R) 82562V-2 10/100 Network Connection + - Intel(R) 82566DC Gigabit Network Connection + - Intel(R) 82566DC-2 Gigabit Network Connection + - Intel(R) 82566DM Gigabit Network Connection + - Intel(R) 82566MC Gigabit Network Connection + - Intel(R) 82566MM Gigabit Network Connection + - Intel(R) 82567V-3 Gigabit Network Connection + - Intel(R) 82577LC Gigabit Network Connection + - Intel(R) 82578DC Gigabit Network Connection + +NOTE: Jumbo Frames cannot be configured on an 82579-based Network device if +MACSec is enabled on the system. + + +ethtool +------- +The driver utilizes the ethtool interface for driver configuration and +diagnostics, as well as displaying statistical information. The latest ethtool +version is required for this functionality. Download it at: + +https://www.kernel.org/pub/software/network/ethtool/ + +NOTE: When validating enable/disable tests on some parts (for example, 82578), +it is necessary to add a few seconds between tests when working with ethtool. + + +Speed and Duplex Configuration +------------------------------ +In addressing speed and duplex configuration issues, you need to distinguish +between copper-based adapters and fiber-based adapters. + +In the default mode, an Intel(R) Ethernet Network Adapter using copper +connections will attempt to auto-negotiate with its link partner to determine +the best setting. If the adapter cannot establish link with the link partner +using auto-negotiation, you may need to manually configure the adapter and link +partner to identical settings to establish link and pass packets. This should +only be needed when attempting to link with an older switch that does not +support auto-negotiation or one that has been forced to a specific speed or +duplex mode. Your link partner must match the setting you choose. 1 Gbps speeds +and higher cannot be forced. Use the autonegotiation advertising setting to +manually set devices for 1 Gbps and higher. + +Speed, duplex, and autonegotiation advertising are configured through the +ethtool utility. + +Caution: Only experienced network administrators should force speed and duplex +or change autonegotiation advertising manually. The settings at the switch must +always match the adapter settings. Adapter performance may suffer or your +adapter may not operate if you configure the adapter differently from your +switch. + +An Intel(R) Ethernet Network Adapter using fiber-based connections, however, +will not attempt to auto-negotiate with its link partner since those adapters +operate only in full duplex and only at their native speed. + + +Enabling Wake on LAN (WoL) +-------------------------- +WoL is configured through the ethtool utility. + +WoL will be enabled on the system during the next shut down or reboot. For +this driver version, in order to enable WoL, the e1000e driver must be loaded +prior to shutting down or suspending the system. + +NOTE: Wake on LAN is only supported on port A for the following devices: +- Intel(R) PRO/1000 PT Dual Port Network Connection +- Intel(R) PRO/1000 PT Dual Port Server Connection +- Intel(R) PRO/1000 PT Dual Port Server Adapter +- Intel(R) PRO/1000 PF Dual Port Server Adapter +- Intel(R) PRO/1000 PT Quad Port Server Adapter +- Intel(R) Gigabit PT Quad Port Server ExpressModule + + +Support +======= +For general information, go to the Intel support website at: +https://www.intel.com/support/ + +If an issue is identified with the released source code on a supported kernel +with a supported adapter, email the specific information related to the issue +to intel-wired-lan@lists.osuosl.org. diff --git a/Documentation/networking/device_drivers/ethernet/intel/fm10k.rst b/Documentation/networking/device_drivers/ethernet/intel/fm10k.rst new file mode 100644 index 0000000000..396a2c8c3d --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/intel/fm10k.rst @@ -0,0 +1,137 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +============================================================= +Linux Base Driver for Intel(R) Ethernet Multi-host Controller +============================================================= + +August 20, 2018 +Copyright(c) 2015-2018 Intel Corporation. + +Contents +======== +- Identifying Your Adapter +- Additional Configurations +- Performance Tuning +- Known Issues +- Support + +Identifying Your Adapter +======================== +The driver in this release is compatible with devices based on the Intel(R) +Ethernet Multi-host Controller. + +For information on how to identify your adapter, and for the latest Intel +network drivers, refer to the Intel Support website: +https://www.intel.com/support + + +Flow Control +------------ +The Intel(R) Ethernet Switch Host Interface Driver does not support Flow +Control. It will not send pause frames. This may result in dropped frames. + + +Virtual Functions (VFs) +----------------------- +Use sysfs to enable VFs. +Valid Range: 0-64 + +For example:: + + echo $num_vf_enabled > /sys/class/net/$dev/device/sriov_numvfs //enable VFs + echo 0 > /sys/class/net/$dev/device/sriov_numvfs //disable VFs + +NOTE: Neither the device nor the driver control how VFs are mapped into config +space. Bus layout will vary by operating system. On operating systems that +support it, you can check sysfs to find the mapping. + +NOTE: When SR-IOV mode is enabled, hardware VLAN filtering and VLAN tag +stripping/insertion will remain enabled. Please remove the old VLAN filter +before the new VLAN filter is added. For example:: + + ip link set eth0 vf 0 vlan 100 // set vlan 100 for VF 0 + ip link set eth0 vf 0 vlan 0 // Delete vlan 100 + ip link set eth0 vf 0 vlan 200 // set a new vlan 200 for VF 0 + + +Additional Features and Configurations +====================================== + +Jumbo Frames +------------ +Jumbo Frames support is enabled by changing the Maximum Transmission Unit (MTU) +to a value larger than the default value of 1500. + +Use the ifconfig command to increase the MTU size. For example, enter the +following where <x> is the interface number:: + + ifconfig eth<x> mtu 9000 up + +Alternatively, you can use the ip command as follows:: + + ip link set mtu 9000 dev eth<x> + ip link set up dev eth<x> + +This setting is not saved across reboots. The setting change can be made +permanent by adding 'MTU=9000' to the file: + +- For RHEL: /etc/sysconfig/network-scripts/ifcfg-eth<x> +- For SLES: /etc/sysconfig/network/<config_file> + +NOTE: The maximum MTU setting for Jumbo Frames is 15342. This value coincides +with the maximum Jumbo Frames size of 15364 bytes. + +NOTE: This driver will attempt to use multiple page sized buffers to receive +each jumbo packet. This should help to avoid buffer starvation issues when +allocating receive packets. + + +Generic Receive Offload, aka GRO +-------------------------------- +The driver supports the in-kernel software implementation of GRO. GRO has +shown that by coalescing Rx traffic into larger chunks of data, CPU +utilization can be significantly reduced when under large Rx load. GRO is an +evolution of the previously-used LRO interface. GRO is able to coalesce +other protocols besides TCP. It's also safe to use with configurations that +are problematic for LRO, namely bridging and iSCSI. + + + +Supported ethtool Commands and Options for Filtering +---------------------------------------------------- +-n --show-nfc + Retrieves the receive network flow classification configurations. + +rx-flow-hash tcp4|udp4|ah4|esp4|sctp4|tcp6|udp6|ah6|esp6|sctp6 + Retrieves the hash options for the specified network traffic type. + +-N --config-nfc + Configures the receive network flow classification. + +rx-flow-hash tcp4|udp4|ah4|esp4|sctp4|tcp6|udp6|ah6|esp6|sctp6 m|v|t|s|d|f|n|r + Configures the hash options for the specified network traffic type. + +- udp4: UDP over IPv4 +- udp6: UDP over IPv6 +- f Hash on bytes 0 and 1 of the Layer 4 header of the rx packet. +- n Hash on bytes 2 and 3 of the Layer 4 header of the rx packet. + + +Known Issues/Troubleshooting +============================ + +Enabling SR-IOV in a 64-bit Microsoft Windows Server 2012/R2 guest OS under Linux KVM +------------------------------------------------------------------------------------- +KVM Hypervisor/VMM supports direct assignment of a PCIe device to a VM. This +includes traditional PCIe devices, as well as SR-IOV-capable devices based on +the Intel Ethernet Controller XL710. + + +Support +======= +For general information, go to the Intel support website at: +https://www.intel.com/support/ + +If an issue is identified with the released source code on a supported kernel +with a supported adapter, email the specific information related to the issue +to intel-wired-lan@lists.osuosl.org. diff --git a/Documentation/networking/device_drivers/ethernet/intel/i40e.rst b/Documentation/networking/device_drivers/ethernet/intel/i40e.rst new file mode 100644 index 0000000000..4fbaa1a2d6 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/intel/i40e.rst @@ -0,0 +1,766 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +================================================================= +Linux Base Driver for the Intel(R) Ethernet Controller 700 Series +================================================================= + +Intel 40 Gigabit Linux driver. +Copyright(c) 1999-2018 Intel Corporation. + +Contents +======== + +- Overview +- Identifying Your Adapter +- Intel(R) Ethernet Flow Director +- Additional Configurations +- Known Issues +- Support + + +Driver information can be obtained using ethtool, lspci, and ifconfig. +Instructions on updating ethtool can be found in the section Additional +Configurations later in this document. + +For questions related to hardware requirements, refer to the documentation +supplied with your Intel adapter. All hardware requirements listed apply to use +with Linux. + + +Identifying Your Adapter +======================== +The driver is compatible with devices based on the following: + + * Intel(R) Ethernet Controller X710 + * Intel(R) Ethernet Controller XL710 + * Intel(R) Ethernet Network Connection X722 + * Intel(R) Ethernet Controller XXV710 + +For the best performance, make sure the latest NVM/FW is installed on your +device. + +For information on how to identify your adapter, and for the latest NVM/FW +images and Intel network drivers, refer to the Intel Support website: +https://www.intel.com/support + +SFP+ and QSFP+ Devices +---------------------- +For information about supported media, refer to this document: +https://www.intel.com/content/dam/www/public/us/en/documents/release-notes/xl710-ethernet-controller-feature-matrix.pdf + +NOTE: Some adapters based on the Intel(R) Ethernet Controller 700 Series only +support Intel Ethernet Optics modules. On these adapters, other modules are not +supported and will not function. In all cases Intel recommends using Intel +Ethernet Optics; other modules may function but are not validated by Intel. +Contact Intel for supported media types. + +NOTE: For connections based on Intel(R) Ethernet Controller 700 Series, support +is dependent on your system board. Please see your vendor for details. + +NOTE: In systems that do not have adequate airflow to cool the adapter and +optical modules, you must use high temperature optical modules. + +Virtual Functions (VFs) +----------------------- +Use sysfs to enable VFs. For example:: + + #echo $num_vf_enabled > /sys/class/net/$dev/device/sriov_numvfs #enable VFs + #echo 0 > /sys/class/net/$dev/device/sriov_numvfs #disable VFs + +For example, the following instructions will configure PF eth0 and the first VF +on VLAN 10:: + + $ ip link set dev eth0 vf 0 vlan 10 + +VLAN Tag Packet Steering +------------------------ +Allows you to send all packets with a specific VLAN tag to a particular SR-IOV +virtual function (VF). Further, this feature allows you to designate a +particular VF as trusted, and allows that trusted VF to request selective +promiscuous mode on the Physical Function (PF). + +To set a VF as trusted or untrusted, enter the following command in the +Hypervisor:: + + # ip link set dev eth0 vf 1 trust [on|off] + +Once the VF is designated as trusted, use the following commands in the VM to +set the VF to promiscuous mode. + +:: + + For promiscuous all: + #ip link set eth2 promisc on + Where eth2 is a VF interface in the VM + + For promiscuous Multicast: + #ip link set eth2 allmulticast on + Where eth2 is a VF interface in the VM + +NOTE: By default, the ethtool priv-flag vf-true-promisc-support is set to +"off",meaning that promiscuous mode for the VF will be limited. To set the +promiscuous mode for the VF to true promiscuous and allow the VF to see all +ingress traffic, use the following command:: + + #ethtool -set-priv-flags p261p1 vf-true-promisc-support on + +The vf-true-promisc-support priv-flag does not enable promiscuous mode; rather, +it designates which type of promiscuous mode (limited or true) you will get +when you enable promiscuous mode using the ip link commands above. Note that +this is a global setting that affects the entire device. However,the +vf-true-promisc-support priv-flag is only exposed to the first PF of the +device. The PF remains in limited promiscuous mode (unless it is in MFP mode) +regardless of the vf-true-promisc-support setting. + +Now add a VLAN interface on the VF interface:: + + #ip link add link eth2 name eth2.100 type vlan id 100 + +Note that the order in which you set the VF to promiscuous mode and add the +VLAN interface does not matter (you can do either first). The end result in +this example is that the VF will get all traffic that is tagged with VLAN 100. + +Intel(R) Ethernet Flow Director +------------------------------- +The Intel Ethernet Flow Director performs the following tasks: + +- Directs receive packets according to their flows to different queues. +- Enables tight control on routing a flow in the platform. +- Matches flows and CPU cores for flow affinity. +- Supports multiple parameters for flexible flow classification and load + balancing (in SFP mode only). + +NOTE: The Linux i40e driver supports the following flow types: IPv4, TCPv4, and +UDPv4. For a given flow type, it supports valid combinations of IP addresses +(source or destination) and UDP/TCP ports (source and destination). For +example, you can supply only a source IP address, a source IP address and a +destination port, or any combination of one or more of these four parameters. + +NOTE: The Linux i40e driver allows you to filter traffic based on a +user-defined flexible two-byte pattern and offset by using the ethtool user-def +and mask fields. Only L3 and L4 flow types are supported for user-defined +flexible filters. For a given flow type, you must clear all Intel Ethernet Flow +Director filters before changing the input set (for that flow type). + +To enable or disable the Intel Ethernet Flow Director:: + + # ethtool -K ethX ntuple <on|off> + +When disabling ntuple filters, all the user programmed filters are flushed from +the driver cache and hardware. All needed filters must be re-added when ntuple +is re-enabled. + +To add a filter that directs packet to queue 2, use -U or -N switch:: + + # ethtool -N ethX flow-type tcp4 src-ip 192.168.10.1 dst-ip \ + 192.168.10.2 src-port 2000 dst-port 2001 action 2 [loc 1] + +To set a filter using only the source and destination IP address:: + + # ethtool -N ethX flow-type tcp4 src-ip 192.168.10.1 dst-ip \ + 192.168.10.2 action 2 [loc 1] + +To see the list of filters currently present:: + + # ethtool <-u|-n> ethX + +Application Targeted Routing (ATR) Perfect Filters +-------------------------------------------------- +ATR is enabled by default when the kernel is in multiple transmit queue mode. +An ATR Intel Ethernet Flow Director filter rule is added when a TCP-IP flow +starts and is deleted when the flow ends. When a TCP-IP Intel Ethernet Flow +Director rule is added from ethtool (Sideband filter), ATR is turned off by the +driver. To re-enable ATR, the sideband can be disabled with the ethtool -K +option. For example:: + + ethtool -K [adapter] ntuple [off|on] + +If sideband is re-enabled after ATR is re-enabled, ATR remains enabled until a +TCP-IP flow is added. When all TCP-IP sideband rules are deleted, ATR is +automatically re-enabled. + +Packets that match the ATR rules are counted in fdir_atr_match stats in +ethtool, which also can be used to verify whether ATR rules still exist. + +Sideband Perfect Filters +------------------------ +Sideband Perfect Filters are used to direct traffic that matches specified +characteristics. They are enabled through ethtool's ntuple interface. To add a +new filter use the following command:: + + ethtool -U <device> flow-type <type> src-ip <ip> dst-ip <ip> src-port <port> \ + dst-port <port> action <queue> + +Where: + <device> - the ethernet device to program + <type> - can be ip4, tcp4, udp4, or sctp4 + <ip> - the ip address to match on + <port> - the port number to match on + <queue> - the queue to direct traffic towards (-1 discards matching traffic) + +Use the following command to display all of the active filters:: + + ethtool -u <device> + +Use the following command to delete a filter:: + + ethtool -U <device> delete <N> + +Where <N> is the filter id displayed when printing all the active filters, and +may also have been specified using "loc <N>" when adding the filter. + +The following example matches TCP traffic sent from 192.168.0.1, port 5300, +directed to 192.168.0.5, port 80, and sends it to queue 7:: + + ethtool -U enp130s0 flow-type tcp4 src-ip 192.168.0.1 dst-ip 192.168.0.5 \ + src-port 5300 dst-port 80 action 7 + +For each flow-type, the programmed filters must all have the same matching +input set. For example, issuing the following two commands is acceptable:: + + ethtool -U enp130s0 flow-type ip4 src-ip 192.168.0.1 src-port 5300 action 7 + ethtool -U enp130s0 flow-type ip4 src-ip 192.168.0.5 src-port 55 action 10 + +Issuing the next two commands, however, is not acceptable, since the first +specifies src-ip and the second specifies dst-ip:: + + ethtool -U enp130s0 flow-type ip4 src-ip 192.168.0.1 src-port 5300 action 7 + ethtool -U enp130s0 flow-type ip4 dst-ip 192.168.0.5 src-port 55 action 10 + +The second command will fail with an error. You may program multiple filters +with the same fields, using different values, but, on one device, you may not +program two tcp4 filters with different matching fields. + +Matching on a sub-portion of a field is not supported by the i40e driver, thus +partial mask fields are not supported. + +The driver also supports matching user-defined data within the packet payload. +This flexible data is specified using the "user-def" field of the ethtool +command in the following way: + ++----------------------------+--------------------------+ +| 31 28 24 20 16 | 15 12 8 4 0 | ++----------------------------+--------------------------+ +| offset into packet payload | 2 bytes of flexible data | ++----------------------------+--------------------------+ + +For example, + +:: + + ... user-def 0x4FFFF ... + +tells the filter to look 4 bytes into the payload and match that value against +0xFFFF. The offset is based on the beginning of the payload, and not the +beginning of the packet. Thus + +:: + + flow-type tcp4 ... user-def 0x8BEAF ... + +would match TCP/IPv4 packets which have the value 0xBEAF 8 bytes into the +TCP/IPv4 payload. + +Note that ICMP headers are parsed as 4 bytes of header and 4 bytes of payload. +Thus to match the first byte of the payload, you must actually add 4 bytes to +the offset. Also note that ip4 filters match both ICMP frames as well as raw +(unknown) ip4 frames, where the payload will be the L3 payload of the IP4 frame. + +The maximum offset is 64. The hardware will only read up to 64 bytes of data +from the payload. The offset must be even because the flexible data is 2 bytes +long and must be aligned to byte 0 of the packet payload. + +The user-defined flexible offset is also considered part of the input set and +cannot be programmed separately for multiple filters of the same type. However, +the flexible data is not part of the input set and multiple filters may use the +same offset but match against different data. + +To create filters that direct traffic to a specific Virtual Function, use the +"action" parameter. Specify the action as a 64 bit value, where the lower 32 +bits represents the queue number, while the next 8 bits represent which VF. +Note that 0 is the PF, so the VF identifier is offset by 1. For example:: + + ... action 0x800000002 ... + +specifies to direct traffic to Virtual Function 7 (8 minus 1) into queue 2 of +that VF. + +Note that these filters will not break internal routing rules, and will not +route traffic that otherwise would not have been sent to the specified Virtual +Function. + +Setting the link-down-on-close Private Flag +------------------------------------------- +When the link-down-on-close private flag is set to "on", the port's link will +go down when the interface is brought down using the ifconfig ethX down command. + +Use ethtool to view and set link-down-on-close, as follows:: + + ethtool --show-priv-flags ethX + ethtool --set-priv-flags ethX link-down-on-close [on|off] + +Viewing Link Messages +--------------------- +Link messages will not be displayed to the console if the distribution is +restricting system messages. In order to see network driver link messages on +your console, set dmesg to eight by entering the following:: + + dmesg -n 8 + +NOTE: This setting is not saved across reboots. + +Jumbo Frames +------------ +Jumbo Frames support is enabled by changing the Maximum Transmission Unit (MTU) +to a value larger than the default value of 1500. + +Use the ifconfig command to increase the MTU size. For example, enter the +following where <x> is the interface number:: + + ifconfig eth<x> mtu 9000 up + +Alternatively, you can use the ip command as follows:: + + ip link set mtu 9000 dev eth<x> + ip link set up dev eth<x> + +This setting is not saved across reboots. The setting change can be made +permanent by adding 'MTU=9000' to the file:: + + /etc/sysconfig/network-scripts/ifcfg-eth<x> // for RHEL + /etc/sysconfig/network/<config_file> // for SLES + +NOTE: The maximum MTU setting for Jumbo Frames is 9702. This value coincides +with the maximum Jumbo Frames size of 9728 bytes. + +NOTE: This driver will attempt to use multiple page sized buffers to receive +each jumbo packet. This should help to avoid buffer starvation issues when +allocating receive packets. + +ethtool +------- +The driver utilizes the ethtool interface for driver configuration and +diagnostics, as well as displaying statistical information. The latest ethtool +version is required for this functionality. Download it at: +https://www.kernel.org/pub/software/network/ethtool/ + +Supported ethtool Commands and Options for Filtering +---------------------------------------------------- +-n --show-nfc + Retrieves the receive network flow classification configurations. + +rx-flow-hash tcp4|udp4|ah4|esp4|sctp4|tcp6|udp6|ah6|esp6|sctp6 + Retrieves the hash options for the specified network traffic type. + +-N --config-nfc + Configures the receive network flow classification. + +rx-flow-hash tcp4|udp4|ah4|esp4|sctp4|tcp6|udp6|ah6|esp6|sctp6 m|v|t|s|d|f|n|r... + Configures the hash options for the specified network traffic type. + +udp4 UDP over IPv4 +udp6 UDP over IPv6 + +f Hash on bytes 0 and 1 of the Layer 4 header of the Rx packet. +n Hash on bytes 2 and 3 of the Layer 4 header of the Rx packet. + +Speed and Duplex Configuration +------------------------------ +In addressing speed and duplex configuration issues, you need to distinguish +between copper-based adapters and fiber-based adapters. + +In the default mode, an Intel(R) Ethernet Network Adapter using copper +connections will attempt to auto-negotiate with its link partner to determine +the best setting. If the adapter cannot establish link with the link partner +using auto-negotiation, you may need to manually configure the adapter and link +partner to identical settings to establish link and pass packets. This should +only be needed when attempting to link with an older switch that does not +support auto-negotiation or one that has been forced to a specific speed or +duplex mode. Your link partner must match the setting you choose. 1 Gbps speeds +and higher cannot be forced. Use the autonegotiation advertising setting to +manually set devices for 1 Gbps and higher. + +NOTE: You cannot set the speed for devices based on the Intel(R) Ethernet +Network Adapter XXV710 based devices. + +Speed, duplex, and autonegotiation advertising are configured through the +ethtool utility. + +Caution: Only experienced network administrators should force speed and duplex +or change autonegotiation advertising manually. The settings at the switch must +always match the adapter settings. Adapter performance may suffer or your +adapter may not operate if you configure the adapter differently from your +switch. + +An Intel(R) Ethernet Network Adapter using fiber-based connections, however, +will not attempt to auto-negotiate with its link partner since those adapters +operate only in full duplex and only at their native speed. + +NAPI +---- +NAPI (Rx polling mode) is supported in the i40e driver. + +See :ref:`Documentation/networking/napi.rst <napi>` for more information. + +Flow Control +------------ +Ethernet Flow Control (IEEE 802.3x) can be configured with ethtool to enable +receiving and transmitting pause frames for i40e. When transmit is enabled, +pause frames are generated when the receive packet buffer crosses a predefined +threshold. When receive is enabled, the transmit unit will halt for the time +delay specified when a pause frame is received. + +NOTE: You must have a flow control capable link partner. + +Flow Control is on by default. + +Use ethtool to change the flow control settings. + +To enable or disable Rx or Tx Flow Control:: + + ethtool -A eth? rx <on|off> tx <on|off> + +Note: This command only enables or disables Flow Control if auto-negotiation is +disabled. If auto-negotiation is enabled, this command changes the parameters +used for auto-negotiation with the link partner. + +To enable or disable auto-negotiation:: + + ethtool -s eth? autoneg <on|off> + +Note: Flow Control auto-negotiation is part of link auto-negotiation. Depending +on your device, you may not be able to change the auto-negotiation setting. + +RSS Hash Flow +------------- +Allows you to set the hash bytes per flow type and any combination of one or +more options for Receive Side Scaling (RSS) hash byte configuration. + +:: + + # ethtool -N <dev> rx-flow-hash <type> <option> + +Where <type> is: + tcp4 signifying TCP over IPv4 + udp4 signifying UDP over IPv4 + tcp6 signifying TCP over IPv6 + udp6 signifying UDP over IPv6 +And <option> is one or more of: + s Hash on the IP source address of the Rx packet. + d Hash on the IP destination address of the Rx packet. + f Hash on bytes 0 and 1 of the Layer 4 header of the Rx packet. + n Hash on bytes 2 and 3 of the Layer 4 header of the Rx packet. + +MAC and VLAN anti-spoofing feature +---------------------------------- +When a malicious driver attempts to send a spoofed packet, it is dropped by the +hardware and not transmitted. +NOTE: This feature can be disabled for a specific Virtual Function (VF):: + + ip link set <pf dev> vf <vf id> spoofchk {off|on} + +IEEE 1588 Precision Time Protocol (PTP) Hardware Clock (PHC) +------------------------------------------------------------ +Precision Time Protocol (PTP) is used to synchronize clocks in a computer +network. PTP support varies among Intel devices that support this driver. Use +"ethtool -T <netdev name>" to get a definitive list of PTP capabilities +supported by the device. + +IEEE 802.1ad (QinQ) Support +--------------------------- +The IEEE 802.1ad standard, informally known as QinQ, allows for multiple VLAN +IDs within a single Ethernet frame. VLAN IDs are sometimes referred to as +"tags," and multiple VLAN IDs are thus referred to as a "tag stack." Tag stacks +allow L2 tunneling and the ability to segregate traffic within a particular +VLAN ID, among other uses. + +The following are examples of how to configure 802.1ad (QinQ):: + + ip link add link eth0 eth0.24 type vlan proto 802.1ad id 24 + ip link add link eth0.24 eth0.24.371 type vlan proto 802.1Q id 371 + +Where "24" and "371" are example VLAN IDs. + +NOTES: + Receive checksum offloads, cloud filters, and VLAN acceleration are not + supported for 802.1ad (QinQ) packets. + +VXLAN and GENEVE Overlay HW Offloading +-------------------------------------- +Virtual Extensible LAN (VXLAN) allows you to extend an L2 network over an L3 +network, which may be useful in a virtualized or cloud environment. Some +Intel(R) Ethernet Network devices perform VXLAN processing, offloading it from +the operating system. This reduces CPU utilization. + +VXLAN offloading is controlled by the Tx and Rx checksum offload options +provided by ethtool. That is, if Tx checksum offload is enabled, and the +adapter has the capability, VXLAN offloading is also enabled. + +Support for VXLAN and GENEVE HW offloading is dependent on kernel support of +the HW offloading features. + +Multiple Functions per Port +--------------------------- +Some adapters based on the Intel Ethernet Controller X710/XL710 support +multiple functions on a single physical port. Configure these functions through +the System Setup/BIOS. + +Minimum TX Bandwidth is the guaranteed minimum data transmission bandwidth, as +a percentage of the full physical port link speed, that the partition will +receive. The bandwidth the partition is awarded will never fall below the level +you specify. + +The range for the minimum bandwidth values is: +1 to ((100 minus # of partitions on the physical port) plus 1) +For example, if a physical port has 4 partitions, the range would be: +1 to ((100 - 4) + 1 = 97) + +The Maximum Bandwidth percentage represents the maximum transmit bandwidth +allocated to the partition as a percentage of the full physical port link +speed. The accepted range of values is 1-100. The value is used as a limiter, +should you chose that any one particular function not be able to consume 100% +of a port's bandwidth (should it be available). The sum of all the values for +Maximum Bandwidth is not restricted, because no more than 100% of a port's +bandwidth can ever be used. + +NOTE: X710/XXV710 devices fail to enable Max VFs (64) when Multiple Functions +per Port (MFP) and SR-IOV are enabled. An error from i40e is logged that says +"add vsi failed for VF N, aq_err 16". To workaround the issue, enable less than +64 virtual functions (VFs). + +Data Center Bridging (DCB) +-------------------------- +DCB is a configuration Quality of Service implementation in hardware. It uses +the VLAN priority tag (802.1p) to filter traffic. That means that there are 8 +different priorities that traffic can be filtered into. It also enables +priority flow control (802.1Qbb) which can limit or eliminate the number of +dropped packets during network stress. Bandwidth can be allocated to each of +these priorities, which is enforced at the hardware level (802.1Qaz). + +Adapter firmware implements LLDP and DCBX protocol agents as per 802.1AB and +802.1Qaz respectively. The firmware based DCBX agent runs in willing mode only +and can accept settings from a DCBX capable peer. Software configuration of +DCBX parameters via dcbtool/lldptool are not supported. + +NOTE: Firmware LLDP can be disabled by setting the private flag disable-fw-lldp. + +The i40e driver implements the DCB netlink interface layer to allow user-space +to communicate with the driver and query DCB configuration for the port. + +NOTE: +The kernel assumes that TC0 is available, and will disable Priority Flow +Control (PFC) on the device if TC0 is not available. To fix this, ensure TC0 is +enabled when setting up DCB on your switch. + +Interrupt Rate Limiting +----------------------- +:Valid Range: 0-235 (0=no limit) + +The Intel(R) Ethernet Controller XL710 family supports an interrupt rate +limiting mechanism. The user can control, via ethtool, the number of +microseconds between interrupts. + +Syntax:: + + # ethtool -C ethX rx-usecs-high N + +The range of 0-235 microseconds provides an effective range of 4,310 to 250,000 +interrupts per second. The value of rx-usecs-high can be set independently of +rx-usecs and tx-usecs in the same ethtool command, and is also independent of +the adaptive interrupt moderation algorithm. The underlying hardware supports +granularity in 4-microsecond intervals, so adjacent values may result in the +same interrupt rate. + +One possible use case is the following:: + + # ethtool -C ethX adaptive-rx off adaptive-tx off rx-usecs-high 20 rx-usecs \ + 5 tx-usecs 5 + +The above command would disable adaptive interrupt moderation, and allow a +maximum of 5 microseconds before indicating a receive or transmit was complete. +However, instead of resulting in as many as 200,000 interrupts per second, it +limits total interrupts per second to 50,000 via the rx-usecs-high parameter. + +Performance Optimization +======================== +Driver defaults are meant to fit a wide variety of workloads, but if further +optimization is required we recommend experimenting with the following settings. + +NOTE: For better performance when processing small (64B) frame sizes, try +enabling Hyper threading in the BIOS in order to increase the number of logical +cores in the system and subsequently increase the number of queues available to +the adapter. + +Virtualized Environments +------------------------ +1. Disable XPS on both ends by using the included virt_perf_default script +or by running the following command as root:: + + for file in `ls /sys/class/net/<ethX>/queues/tx-*/xps_cpus`; + do echo 0 > $file; done + +2. Using the appropriate mechanism (vcpupin) in the vm, pin the cpu's to +individual lcpu's, making sure to use a set of cpu's included in the +device's local_cpulist: /sys/class/net/<ethX>/device/local_cpulist. + +3. Configure as many Rx/Tx queues in the VM as available. Do not rely on +the default setting of 1. + + +Non-virtualized Environments +---------------------------- +Pin the adapter's IRQs to specific cores by disabling the irqbalance service +and using the included set_irq_affinity script. Please see the script's help +text for further options. + +- The following settings will distribute the IRQs across all the cores evenly:: + + # scripts/set_irq_affinity -x all <interface1> , [ <interface2>, ... ] + +- The following settings will distribute the IRQs across all the cores that are + local to the adapter (same NUMA node):: + + # scripts/set_irq_affinity -x local <interface1> ,[ <interface2>, ... ] + +For very CPU intensive workloads, we recommend pinning the IRQs to all cores. + +For IP Forwarding: Disable Adaptive ITR and lower Rx and Tx interrupts per +queue using ethtool. + +- Setting rx-usecs and tx-usecs to 125 will limit interrupts to about 8000 + interrupts per second per queue. + +:: + + # ethtool -C <interface> adaptive-rx off adaptive-tx off rx-usecs 125 \ + tx-usecs 125 + +For lower CPU utilization: Disable Adaptive ITR and lower Rx and Tx interrupts +per queue using ethtool. + +- Setting rx-usecs and tx-usecs to 250 will limit interrupts to about 4000 + interrupts per second per queue. + +:: + + # ethtool -C <interface> adaptive-rx off adaptive-tx off rx-usecs 250 \ + tx-usecs 250 + +For lower latency: Disable Adaptive ITR and ITR by setting Rx and Tx to 0 using +ethtool. + +:: + + # ethtool -C <interface> adaptive-rx off adaptive-tx off rx-usecs 0 \ + tx-usecs 0 + +Application Device Queues (ADq) +------------------------------- +Application Device Queues (ADq) allows you to dedicate one or more queues to a +specific application. This can reduce latency for the specified application, +and allow Tx traffic to be rate limited per application. Follow the steps below +to set ADq. + +1. Create traffic classes (TCs). Maximum of 8 TCs can be created per interface. +The shaper bw_rlimit parameter is optional. + +Example: Sets up two tcs, tc0 and tc1, with 16 queues each and max tx rate set +to 1Gbit for tc0 and 3Gbit for tc1. + +:: + + # tc qdisc add dev <interface> root mqprio num_tc 2 map 0 0 0 0 1 1 1 1 + queues 16@0 16@16 hw 1 mode channel shaper bw_rlimit min_rate 1Gbit 2Gbit + max_rate 1Gbit 3Gbit + +map: priority mapping for up to 16 priorities to tcs (e.g. map 0 0 0 0 1 1 1 1 +sets priorities 0-3 to use tc0 and 4-7 to use tc1) + +queues: for each tc, <num queues>@<offset> (e.g. queues 16@0 16@16 assigns +16 queues to tc0 at offset 0 and 16 queues to tc1 at offset 16. Max total +number of queues for all tcs is 64 or number of cores, whichever is lower.) + +hw 1 mode channel: ‘channel’ with ‘hw’ set to 1 is a new new hardware +offload mode in mqprio that makes full use of the mqprio options, the +TCs, the queue configurations, and the QoS parameters. + +shaper bw_rlimit: for each tc, sets minimum and maximum bandwidth rates. +Totals must be equal or less than port speed. + +For example: min_rate 1Gbit 3Gbit: Verify bandwidth limit using network +monitoring tools such as `ifstat` or `sar -n DEV [interval] [number of samples]` + +2. Enable HW TC offload on interface:: + + # ethtool -K <interface> hw-tc-offload on + +3. Apply TCs to ingress (RX) flow of interface:: + + # tc qdisc add dev <interface> ingress + +NOTES: + - Run all tc commands from the iproute2 <pathtoiproute2>/tc/ directory. + - ADq is not compatible with cloud filters. + - Setting up channels via ethtool (ethtool -L) is not supported when the + TCs are configured using mqprio. + - You must have iproute2 latest version + - NVM version 6.01 or later is required. + - ADq cannot be enabled when any the following features are enabled: Data + Center Bridging (DCB), Multiple Functions per Port (MFP), or Sideband + Filters. + - If another driver (for example, DPDK) has set cloud filters, you cannot + enable ADq. + - Tunnel filters are not supported in ADq. If encapsulated packets do + arrive in non-tunnel mode, filtering will be done on the inner headers. + For example, for VXLAN traffic in non-tunnel mode, PCTYPE is identified + as a VXLAN encapsulated packet, outer headers are ignored. Therefore, + inner headers are matched. + - If a TC filter on a PF matches traffic over a VF (on the PF), that + traffic will be routed to the appropriate queue of the PF, and will + not be passed on the VF. Such traffic will end up getting dropped higher + up in the TCP/IP stack as it does not match PF address data. + - If traffic matches multiple TC filters that point to different TCs, + that traffic will be duplicated and sent to all matching TC queues. + The hardware switch mirrors the packet to a VSI list when multiple + filters are matched. + + +Known Issues/Troubleshooting +============================ + +NOTE: 1 Gb devices based on the Intel(R) Ethernet Network Connection X722 do +not support the following features: + + * Data Center Bridging (DCB) + * QOS + * VMQ + * SR-IOV + * Task Encapsulation offload (VXLAN, NVGRE) + * Energy Efficient Ethernet (EEE) + * Auto-media detect + +Unexpected Issues when the device driver and DPDK share a device +---------------------------------------------------------------- +Unexpected issues may result when an i40e device is in multi driver mode and +the kernel driver and DPDK driver are sharing the device. This is because +access to the global NIC resources is not synchronized between multiple +drivers. Any change to the global NIC configuration (writing to a global +register, setting global configuration by AQ, or changing switch modes) will +affect all ports and drivers on the device. Loading DPDK with the +"multi-driver" module parameter may mitigate some of the issues. + +TC0 must be enabled when setting up DCB on a switch +--------------------------------------------------- +The kernel assumes that TC0 is available, and will disable Priority Flow +Control (PFC) on the device if TC0 is not available. To fix this, ensure TC0 is +enabled when setting up DCB on your switch. + + +Support +======= +For general information, go to the Intel support website at: +https://www.intel.com/support/ + +If an issue is identified with the released source code on a supported kernel +with a supported adapter, email the specific information related to the issue +to intel-wired-lan@lists.osuosl.org. diff --git a/Documentation/networking/device_drivers/ethernet/intel/iavf.rst b/Documentation/networking/device_drivers/ethernet/intel/iavf.rst new file mode 100644 index 0000000000..eb926c3bd4 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/intel/iavf.rst @@ -0,0 +1,326 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +================================================================= +Linux Base Driver for Intel(R) Ethernet Adaptive Virtual Function +================================================================= + +Intel Ethernet Adaptive Virtual Function Linux driver. +Copyright(c) 2013-2018 Intel Corporation. + +Contents +======== + +- Overview +- Identifying Your Adapter +- Additional Configurations +- Known Issues/Troubleshooting +- Support + +Overview +======== + +This file describes the iavf Linux Base Driver. This driver was formerly +called i40evf. + +The iavf driver supports the below mentioned virtual function devices and +can only be activated on kernels running the i40e or newer Physical Function +(PF) driver compiled with CONFIG_PCI_IOV. The iavf driver requires +CONFIG_PCI_MSI to be enabled. + +The guest OS loading the iavf driver must support MSI-X interrupts. + +Identifying Your Adapter +======================== + +The driver in this kernel is compatible with devices based on the following: + * Intel(R) XL710 X710 Virtual Function + * Intel(R) X722 Virtual Function + * Intel(R) XXV710 Virtual Function + * Intel(R) Ethernet Adaptive Virtual Function + +For the best performance, make sure the latest NVM/FW is installed on your +device. + +For information on how to identify your adapter, and for the latest NVM/FW +images and Intel network drivers, refer to the Intel Support website: +https://www.intel.com/support + + +Additional Features and Configurations +====================================== + +Viewing Link Messages +--------------------- +Link messages will not be displayed to the console if the distribution is +restricting system messages. In order to see network driver link messages on +your console, set dmesg to eight by entering the following:: + + # dmesg -n 8 + +NOTE: + This setting is not saved across reboots. + +ethtool +------- +The driver utilizes the ethtool interface for driver configuration and +diagnostics, as well as displaying statistical information. The latest ethtool +version is required for this functionality. Download it at: +https://www.kernel.org/pub/software/network/ethtool/ + +Setting VLAN Tag Stripping +-------------------------- +If you have applications that require Virtual Functions (VFs) to receive +packets with VLAN tags, you can disable VLAN tag stripping for the VF. The +Physical Function (PF) processes requests issued from the VF to enable or +disable VLAN tag stripping. Note that if the PF has assigned a VLAN to a VF, +then requests from that VF to set VLAN tag stripping will be ignored. + +To enable/disable VLAN tag stripping for a VF, issue the following command +from inside the VM in which you are running the VF:: + + # ethtool -K <if_name> rxvlan on/off + +or alternatively:: + + # ethtool --offload <if_name> rxvlan on/off + +Adaptive Virtual Function +------------------------- +Adaptive Virtual Function (AVF) allows the virtual function driver, or VF, to +adapt to changing feature sets of the physical function driver (PF) with which +it is associated. This allows system administrators to update a PF without +having to update all the VFs associated with it. All AVFs have a single common +device ID and branding string. + +AVFs have a minimum set of features known as "base mode," but may provide +additional features depending on what features are available in the PF with +which the AVF is associated. The following are base mode features: + +- 4 Queue Pairs (QP) and associated Configuration Status Registers (CSRs) + for Tx/Rx +- i40e descriptors and ring format +- Descriptor write-back completion +- 1 control queue, with i40e descriptors, CSRs and ring format +- 5 MSI-X interrupt vectors and corresponding i40e CSRs +- 1 Interrupt Throttle Rate (ITR) index +- 1 Virtual Station Interface (VSI) per VF +- 1 Traffic Class (TC), TC0 +- Receive Side Scaling (RSS) with 64 entry indirection table and key, + configured through the PF +- 1 unicast MAC address reserved per VF +- 16 MAC address filters for each VF +- Stateless offloads - non-tunneled checksums +- AVF device ID +- HW mailbox is used for VF to PF communications (including on Windows) + +IEEE 802.1ad (QinQ) Support +--------------------------- +The IEEE 802.1ad standard, informally known as QinQ, allows for multiple VLAN +IDs within a single Ethernet frame. VLAN IDs are sometimes referred to as +"tags," and multiple VLAN IDs are thus referred to as a "tag stack." Tag stacks +allow L2 tunneling and the ability to segregate traffic within a particular +VLAN ID, among other uses. + +The following are examples of how to configure 802.1ad (QinQ):: + + # ip link add link eth0 eth0.24 type vlan proto 802.1ad id 24 + # ip link add link eth0.24 eth0.24.371 type vlan proto 802.1Q id 371 + +Where "24" and "371" are example VLAN IDs. + +NOTES: + Receive checksum offloads, cloud filters, and VLAN acceleration are not + supported for 802.1ad (QinQ) packets. + +Application Device Queues (ADq) +------------------------------- +Application Device Queues (ADq) allows you to dedicate one or more queues to a +specific application. This can reduce latency for the specified application, +and allow Tx traffic to be rate limited per application. Follow the steps below +to set ADq. + +Requirements: + +- The sch_mqprio, act_mirred and cls_flower modules must be loaded +- The latest version of iproute2 +- If another driver (for example, DPDK) has set cloud filters, you cannot + enable ADQ +- Depending on the underlying PF device, ADQ cannot be enabled when the + following features are enabled: + + + Data Center Bridging (DCB) + + Multiple Functions per Port (MFP) + + Sideband Filters + +1. Create traffic classes (TCs). Maximum of 8 TCs can be created per interface. +The shaper bw_rlimit parameter is optional. + +Example: Sets up two tcs, tc0 and tc1, with 16 queues each and max tx rate set +to 1Gbit for tc0 and 3Gbit for tc1. + +:: + + tc qdisc add dev <interface> root mqprio num_tc 2 map 0 0 0 0 1 1 1 1 + queues 16@0 16@16 hw 1 mode channel shaper bw_rlimit min_rate 1Gbit 2Gbit + max_rate 1Gbit 3Gbit + +map: priority mapping for up to 16 priorities to tcs (e.g. map 0 0 0 0 1 1 1 1 +sets priorities 0-3 to use tc0 and 4-7 to use tc1) + +queues: for each tc, <num queues>@<offset> (e.g. queues 16@0 16@16 assigns +16 queues to tc0 at offset 0 and 16 queues to tc1 at offset 16. Max total +number of queues for all tcs is 64 or number of cores, whichever is lower.) + +hw 1 mode channel: ‘channel’ with ‘hw’ set to 1 is a new new hardware +offload mode in mqprio that makes full use of the mqprio options, the +TCs, the queue configurations, and the QoS parameters. + +shaper bw_rlimit: for each tc, sets minimum and maximum bandwidth rates. +Totals must be equal or less than port speed. + +For example: min_rate 1Gbit 3Gbit: Verify bandwidth limit using network +monitoring tools such as ``ifstat`` or ``sar -n DEV [interval] [number of samples]`` + +NOTE: + Setting up channels via ethtool (ethtool -L) is not supported when the + TCs are configured using mqprio. + +2. Enable HW TC offload on interface:: + + # ethtool -K <interface> hw-tc-offload on + +3. Apply TCs to ingress (RX) flow of interface:: + + # tc qdisc add dev <interface> ingress + +NOTES: + - Run all tc commands from the iproute2 <pathtoiproute2>/tc/ directory + - ADq is not compatible with cloud filters + - Setting up channels via ethtool (ethtool -L) is not supported when the TCs + are configured using mqprio + - You must have iproute2 latest version + - NVM version 6.01 or later is required + - ADq cannot be enabled when any the following features are enabled: Data + Center Bridging (DCB), Multiple Functions per Port (MFP), or Sideband Filters + - If another driver (for example, DPDK) has set cloud filters, you cannot + enable ADq + - Tunnel filters are not supported in ADq. If encapsulated packets do arrive + in non-tunnel mode, filtering will be done on the inner headers. For example, + for VXLAN traffic in non-tunnel mode, PCTYPE is identified as a VXLAN + encapsulated packet, outer headers are ignored. Therefore, inner headers are + matched. + - If a TC filter on a PF matches traffic over a VF (on the PF), that traffic + will be routed to the appropriate queue of the PF, and will not be passed on + the VF. Such traffic will end up getting dropped higher up in the TCP/IP + stack as it does not match PF address data. + - If traffic matches multiple TC filters that point to different TCs, that + traffic will be duplicated and sent to all matching TC queues. The hardware + switch mirrors the packet to a VSI list when multiple filters are matched. + + +Known Issues/Troubleshooting +============================ + +Bonding fails with VFs bound to an Intel(R) Ethernet Controller 700 series device +--------------------------------------------------------------------------------- +If you bind Virtual Functions (VFs) to an Intel(R) Ethernet Controller 700 +series based device, the VF slaves may fail when they become the active slave. +If the MAC address of the VF is set by the PF (Physical Function) of the +device, when you add a slave, or change the active-backup slave, Linux bonding +tries to sync the backup slave's MAC address to the same MAC address as the +active slave. Linux bonding will fail at this point. This issue will not occur +if the VF's MAC address is not set by the PF. + +Traffic Is Not Being Passed Between VM and Client +------------------------------------------------- +You may not be able to pass traffic between a client system and a +Virtual Machine (VM) running on a separate host if the Virtual Function +(VF, or Virtual NIC) is not in trusted mode and spoof checking is enabled +on the VF. Note that this situation can occur in any combination of client, +host, and guest operating system. For information on how to set the VF to +trusted mode, refer to the section "VLAN Tag Packet Steering" in this +readme document. For information on setting spoof checking, refer to the +section "MAC and VLAN anti-spoofing feature" in this readme document. + +Do not unload port driver if VF with active VM is bound to it +------------------------------------------------------------- +Do not unload a port's driver if a Virtual Function (VF) with an active Virtual +Machine (VM) is bound to it. Doing so will cause the port to appear to hang. +Once the VM shuts down, or otherwise releases the VF, the command will complete. + +Using four traffic classes fails +-------------------------------- +Do not try to reserve more than three traffic classes in the iavf driver. Doing +so will fail to set any traffic classes and will cause the driver to write +errors to stdout. Use a maximum of three queues to avoid this issue. + +Multiple log error messages on iavf driver removal +-------------------------------------------------- +If you have several VFs and you remove the iavf driver, several instances of +the following log errors are written to the log:: + + Unable to send opcode 2 to PF, err I40E_ERR_QUEUE_EMPTY, aq_err ok + Unable to send the message to VF 2 aq_err 12 + ARQ Overflow Error detected + +Virtual machine does not get link +--------------------------------- +If the virtual machine has more than one virtual port assigned to it, and those +virtual ports are bound to different physical ports, you may not get link on +all of the virtual ports. The following command may work around the issue:: + + # ethtool -r <PF> + +Where <PF> is the PF interface in the host, for example: p5p1. You may need to +run the command more than once to get link on all virtual ports. + +MAC address of Virtual Function changes unexpectedly +---------------------------------------------------- +If a Virtual Function's MAC address is not assigned in the host, then the VF +(virtual function) driver will use a random MAC address. This random MAC +address may change each time the VF driver is reloaded. You can assign a static +MAC address in the host machine. This static MAC address will survive +a VF driver reload. + +Driver Buffer Overflow Fix +-------------------------- +The fix to resolve CVE-2016-8105, referenced in Intel SA-00069 +https://www.intel.com/content/www/us/en/security-center/advisory/intel-sa-00069.html +is included in this and future versions of the driver. + +Multiple Interfaces on Same Ethernet Broadcast Network +------------------------------------------------------ +Due to the default ARP behavior on Linux, it is not possible to have one system +on two IP networks in the same Ethernet broadcast domain (non-partitioned +switch) behave as expected. All Ethernet interfaces will respond to IP traffic +for any IP address assigned to the system. This results in unbalanced receive +traffic. + +If you have multiple interfaces in a server, either turn on ARP filtering by +entering:: + + # echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter + +NOTE: + This setting is not saved across reboots. The configuration change can be + made permanent by adding the following line to the file /etc/sysctl.conf:: + + net.ipv4.conf.all.arp_filter = 1 + +Another alternative is to install the interfaces in separate broadcast domains +(either in different switches or in a switch partitioned to VLANs). + +Rx Page Allocation Errors +------------------------- +'Page allocation failure. order:0' errors may occur under stress. +This is caused by the way the Linux kernel reports this stressed condition. + + +Support +======= +For general information, go to the Intel support website at: +https://support.intel.com + +If an issue is identified with the released source code on the supported kernel +with a supported adapter, email the specific information related to the issue +to intel-wired-lan@lists.osuosl.org. diff --git a/Documentation/networking/device_drivers/ethernet/intel/ice.rst b/Documentation/networking/device_drivers/ethernet/intel/ice.rst new file mode 100644 index 0000000000..e4d065c55e --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/intel/ice.rst @@ -0,0 +1,1021 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +================================================================= +Linux Base Driver for the Intel(R) Ethernet Controller 800 Series +================================================================= + +Intel ice Linux driver. +Copyright(c) 2018-2021 Intel Corporation. + +Contents +======== + +- Overview +- Identifying Your Adapter +- Important Notes +- Additional Features & Configurations +- Performance Optimization + + +The associated Virtual Function (VF) driver for this driver is iavf. + +Driver information can be obtained using ethtool and lspci. + +For questions related to hardware requirements, refer to the documentation +supplied with your Intel adapter. All hardware requirements listed apply to use +with Linux. + +This driver supports XDP (Express Data Path) and AF_XDP zero-copy. Note that +XDP is blocked for frame sizes larger than 3KB. + + +Identifying Your Adapter +======================== +For information on how to identify your adapter, and for the latest Intel +network drivers, refer to the Intel Support website: +https://www.intel.com/support + + +Important Notes +=============== + +Packet drops may occur under receive stress +------------------------------------------- +Devices based on the Intel(R) Ethernet Controller 800 Series are designed to +tolerate a limited amount of system latency during PCIe and DMA transactions. +If these transactions take longer than the tolerated latency, it can impact the +length of time the packets are buffered in the device and associated memory, +which may result in dropped packets. These packets drops typically do not have +a noticeable impact on throughput and performance under standard workloads. + +If these packet drops appear to affect your workload, the following may improve +the situation: + +1) Make sure that your system's physical memory is in a high-performance + configuration, as recommended by the platform vendor. A common + recommendation is for all channels to be populated with a single DIMM + module. +2) In your system's BIOS/UEFI settings, select the "Performance" profile. +3) Your distribution may provide tools like "tuned," which can help tweak + kernel settings to achieve better standard settings for different workloads. + + +Configuring SR-IOV for improved network security +------------------------------------------------ +In a virtualized environment, on Intel(R) Ethernet Network Adapters that +support SR-IOV, the virtual function (VF) may be subject to malicious behavior. +Software-generated layer two frames, like IEEE 802.3x (link flow control), IEEE +802.1Qbb (priority based flow-control), and others of this type, are not +expected and can throttle traffic between the host and the virtual switch, +reducing performance. To resolve this issue, and to ensure isolation from +unintended traffic streams, configure all SR-IOV enabled ports for VLAN tagging +from the administrative interface on the PF. This configuration allows +unexpected, and potentially malicious, frames to be dropped. + +See "Configuring VLAN Tagging on SR-IOV Enabled Adapter Ports" later in this +README for configuration instructions. + + +Do not unload port driver if VF with active VM is bound to it +------------------------------------------------------------- +Do not unload a port's driver if a Virtual Function (VF) with an active Virtual +Machine (VM) is bound to it. Doing so will cause the port to appear to hang. +Once the VM shuts down, or otherwise releases the VF, the command will +complete. + + +Additional Features and Configurations +====================================== + +ethtool +------- +The driver utilizes the ethtool interface for driver configuration and +diagnostics, as well as displaying statistical information. The latest ethtool +version is required for this functionality. Download it at: +https://kernel.org/pub/software/network/ethtool/ + +NOTE: The rx_bytes value of ethtool does not match the rx_bytes value of +Netdev, due to the 4-byte CRC being stripped by the device. The difference +between the two rx_bytes values will be 4 x the number of Rx packets. For +example, if Rx packets are 10 and Netdev (software statistics) displays +rx_bytes as "X", then ethtool (hardware statistics) will display rx_bytes as +"X+40" (4 bytes CRC x 10 packets). + + +Viewing Link Messages +--------------------- +Link messages will not be displayed to the console if the distribution is +restricting system messages. In order to see network driver link messages on +your console, set dmesg to eight by entering the following:: + + # dmesg -n 8 + +NOTE: This setting is not saved across reboots. + + +Dynamic Device Personalization +------------------------------ +Dynamic Device Personalization (DDP) allows you to change the packet processing +pipeline of a device by applying a profile package to the device at runtime. +Profiles can be used to, for example, add support for new protocols, change +existing protocols, or change default settings. DDP profiles can also be rolled +back without rebooting the system. + +The DDP package loads during device initialization. The driver looks for +``intel/ice/ddp/ice.pkg`` in your firmware root (typically ``/lib/firmware/`` +or ``/lib/firmware/updates/``) and checks that it contains a valid DDP package +file. + +NOTE: Your distribution should likely have provided the latest DDP file, but if +ice.pkg is missing, you can find it in the linux-firmware repository or from +intel.com. + +If the driver is unable to load the DDP package, the device will enter Safe +Mode. Safe Mode disables advanced and performance features and supports only +basic traffic and minimal functionality, such as updating the NVM or +downloading a new driver or DDP package. Safe Mode only applies to the affected +physical function and does not impact any other PFs. See the "Intel(R) Ethernet +Adapters and Devices User Guide" for more details on DDP and Safe Mode. + +NOTES: + +- If you encounter issues with the DDP package file, you may need to download + an updated driver or DDP package file. See the log messages for more + information. + +- The ice.pkg file is a symbolic link to the default DDP package file. + +- You cannot update the DDP package if any PF drivers are already loaded. To + overwrite a package, unload all PFs and then reload the driver with the new + package. + +- Only the first loaded PF per device can download a package for that device. + +You can install specific DDP package files for different physical devices in +the same system. To install a specific DDP package file: + +1. Download the DDP package file you want for your device. + +2. Rename the file ice-xxxxxxxxxxxxxxxx.pkg, where 'xxxxxxxxxxxxxxxx' is the + unique 64-bit PCI Express device serial number (in hex) of the device you + want the package downloaded on. The filename must include the complete + serial number (including leading zeros) and be all lowercase. For example, + if the 64-bit serial number is b887a3ffffca0568, then the file name would be + ice-b887a3ffffca0568.pkg. + + To find the serial number from the PCI bus address, you can use the + following command:: + + # lspci -vv -s af:00.0 | grep -i Serial + Capabilities: [150 v1] Device Serial Number b8-87-a3-ff-ff-ca-05-68 + + You can use the following command to format the serial number without the + dashes:: + + # lspci -vv -s af:00.0 | grep -i Serial | awk '{print $7}' | sed s/-//g + b887a3ffffca0568 + +3. Copy the renamed DDP package file to + ``/lib/firmware/updates/intel/ice/ddp/``. If the directory does not yet + exist, create it before copying the file. + +4. Unload all of the PFs on the device. + +5. Reload the driver with the new package. + +NOTE: The presence of a device-specific DDP package file overrides the loading +of the default DDP package file (ice.pkg). + + +Intel(R) Ethernet Flow Director +------------------------------- +The Intel Ethernet Flow Director performs the following tasks: + +- Directs receive packets according to their flows to different queues +- Enables tight control on routing a flow in the platform +- Matches flows and CPU cores for flow affinity + +NOTE: This driver supports the following flow types: + +- IPv4 +- TCPv4 +- UDPv4 +- SCTPv4 +- IPv6 +- TCPv6 +- UDPv6 +- SCTPv6 + +Each flow type supports valid combinations of IP addresses (source or +destination) and UDP/TCP/SCTP ports (source and destination). You can supply +only a source IP address, a source IP address and a destination port, or any +combination of one or more of these four parameters. + +NOTE: This driver allows you to filter traffic based on a user-defined flexible +two-byte pattern and offset by using the ethtool user-def and mask fields. Only +L3 and L4 flow types are supported for user-defined flexible filters. For a +given flow type, you must clear all Intel Ethernet Flow Director filters before +changing the input set (for that flow type). + + +Flow Director Filters +--------------------- +Flow Director filters are used to direct traffic that matches specified +characteristics. They are enabled through ethtool's ntuple interface. To enable +or disable the Intel Ethernet Flow Director and these filters:: + + # ethtool -K <ethX> ntuple <off|on> + +NOTE: When you disable ntuple filters, all the user programmed filters are +flushed from the driver cache and hardware. All needed filters must be re-added +when ntuple is re-enabled. + +To display all of the active filters:: + + # ethtool -u <ethX> + +To add a new filter:: + + # ethtool -U <ethX> flow-type <type> src-ip <ip> [m <ip_mask>] dst-ip <ip> + [m <ip_mask>] src-port <port> [m <port_mask>] dst-port <port> [m <port_mask>] + action <queue> + + Where: + <ethX> - the Ethernet device to program + <type> - can be ip4, tcp4, udp4, sctp4, ip6, tcp6, udp6, sctp6 + <ip> - the IP address to match on + <ip_mask> - the IPv4 address to mask on + NOTE: These filters use inverted masks. + <port> - the port number to match on + <port_mask> - the 16-bit integer for masking + NOTE: These filters use inverted masks. + <queue> - the queue to direct traffic toward (-1 discards the + matched traffic) + +To delete a filter:: + + # ethtool -U <ethX> delete <N> + + Where <N> is the filter ID displayed when printing all the active filters, + and may also have been specified using "loc <N>" when adding the filter. + +EXAMPLES: + +To add a filter that directs packet to queue 2:: + + # ethtool -U <ethX> flow-type tcp4 src-ip 192.168.10.1 dst-ip \ + 192.168.10.2 src-port 2000 dst-port 2001 action 2 [loc 1] + +To set a filter using only the source and destination IP address:: + + # ethtool -U <ethX> flow-type tcp4 src-ip 192.168.10.1 dst-ip \ + 192.168.10.2 action 2 [loc 1] + +To set a filter based on a user-defined pattern and offset:: + + # ethtool -U <ethX> flow-type tcp4 src-ip 192.168.10.1 dst-ip \ + 192.168.10.2 user-def 0x4FFFF action 2 [loc 1] + + where the value of the user-def field contains the offset (4 bytes) and + the pattern (0xffff). + +To match TCP traffic sent from 192.168.0.1, port 5300, directed to 192.168.0.5, +port 80, and then send it to queue 7:: + + # ethtool -U enp130s0 flow-type tcp4 src-ip 192.168.0.1 dst-ip 192.168.0.5 + src-port 5300 dst-port 80 action 7 + +To add a TCPv4 filter with a partial mask for a source IP subnet:: + + # ethtool -U <ethX> flow-type tcp4 src-ip 192.168.0.0 m 0.255.255.255 dst-ip + 192.168.5.12 src-port 12600 dst-port 31 action 12 + +NOTES: + +For each flow-type, the programmed filters must all have the same matching +input set. For example, issuing the following two commands is acceptable:: + + # ethtool -U enp130s0 flow-type ip4 src-ip 192.168.0.1 src-port 5300 action 7 + # ethtool -U enp130s0 flow-type ip4 src-ip 192.168.0.5 src-port 55 action 10 + +Issuing the next two commands, however, is not acceptable, since the first +specifies src-ip and the second specifies dst-ip:: + + # ethtool -U enp130s0 flow-type ip4 src-ip 192.168.0.1 src-port 5300 action 7 + # ethtool -U enp130s0 flow-type ip4 dst-ip 192.168.0.5 src-port 55 action 10 + +The second command will fail with an error. You may program multiple filters +with the same fields, using different values, but, on one device, you may not +program two tcp4 filters with different matching fields. + +The ice driver does not support matching on a subportion of a field, thus +partial mask fields are not supported. + + +Flex Byte Flow Director Filters +------------------------------- +The driver also supports matching user-defined data within the packet payload. +This flexible data is specified using the "user-def" field of the ethtool +command in the following way: + +.. table:: + + ============================== ============================ + ``31 28 24 20 16`` ``15 12 8 4 0`` + ``offset into packet payload`` ``2 bytes of flexible data`` + ============================== ============================ + +For example, + +:: + + ... user-def 0x4FFFF ... + +tells the filter to look 4 bytes into the payload and match that value against +0xFFFF. The offset is based on the beginning of the payload, and not the +beginning of the packet. Thus + +:: + + flow-type tcp4 ... user-def 0x8BEAF ... + +would match TCP/IPv4 packets which have the value 0xBEAF 8 bytes into the +TCP/IPv4 payload. + +Note that ICMP headers are parsed as 4 bytes of header and 4 bytes of payload. +Thus to match the first byte of the payload, you must actually add 4 bytes to +the offset. Also note that ip4 filters match both ICMP frames as well as raw +(unknown) ip4 frames, where the payload will be the L3 payload of the IP4 +frame. + +The maximum offset is 64. The hardware will only read up to 64 bytes of data +from the payload. The offset must be even because the flexible data is 2 bytes +long and must be aligned to byte 0 of the packet payload. + +The user-defined flexible offset is also considered part of the input set and +cannot be programmed separately for multiple filters of the same type. However, +the flexible data is not part of the input set and multiple filters may use the +same offset but match against different data. + + +RSS Hash Flow +------------- +Allows you to set the hash bytes per flow type and any combination of one or +more options for Receive Side Scaling (RSS) hash byte configuration. + +:: + + # ethtool -N <ethX> rx-flow-hash <type> <option> + + Where <type> is: + tcp4 signifying TCP over IPv4 + udp4 signifying UDP over IPv4 + tcp6 signifying TCP over IPv6 + udp6 signifying UDP over IPv6 + And <option> is one or more of: + s Hash on the IP source address of the Rx packet. + d Hash on the IP destination address of the Rx packet. + f Hash on bytes 0 and 1 of the Layer 4 header of the Rx packet. + n Hash on bytes 2 and 3 of the Layer 4 header of the Rx packet. + + +Accelerated Receive Flow Steering (aRFS) +---------------------------------------- +Devices based on the Intel(R) Ethernet Controller 800 Series support +Accelerated Receive Flow Steering (aRFS) on the PF. aRFS is a load-balancing +mechanism that allows you to direct packets to the same CPU where an +application is running or consuming the packets in that flow. + +NOTES: + +- aRFS requires that ntuple filtering is enabled via ethtool. +- aRFS support is limited to the following packet types: + + - TCP over IPv4 and IPv6 + - UDP over IPv4 and IPv6 + - Nonfragmented packets + +- aRFS only supports Flow Director filters, which consist of the + source/destination IP addresses and source/destination ports. +- aRFS and ethtool's ntuple interface both use the device's Flow Director. aRFS + and ntuple features can coexist, but you may encounter unexpected results if + there's a conflict between aRFS and ntuple requests. See "Intel(R) Ethernet + Flow Director" for additional information. + +To set up aRFS: + +1. Enable the Intel Ethernet Flow Director and ntuple filters using ethtool. + +:: + + # ethtool -K <ethX> ntuple on + +2. Set up the number of entries in the global flow table. For example: + +:: + + # NUM_RPS_ENTRIES=16384 + # echo $NUM_RPS_ENTRIES > /proc/sys/net/core/rps_sock_flow_entries + +3. Set up the number of entries in the per-queue flow table. For example: + +:: + + # NUM_RX_QUEUES=64 + # for file in /sys/class/net/$IFACE/queues/rx-*/rps_flow_cnt; do + # echo $(($NUM_RPS_ENTRIES/$NUM_RX_QUEUES)) > $file; + # done + +4. Disable the IRQ balance daemon (this is only a temporary stop of the service + until the next reboot). + +:: + + # systemctl stop irqbalance + +5. Configure the interrupt affinity. + + See ``/Documentation/core-api/irq/irq-affinity.rst`` + + +To disable aRFS using ethtool:: + + # ethtool -K <ethX> ntuple off + +NOTE: This command will disable ntuple filters and clear any aRFS filters in +software and hardware. + +Example Use Case: + +1. Set the server application on the desired CPU (e.g., CPU 4). + +:: + + # taskset -c 4 netserver + +2. Use netperf to route traffic from the client to CPU 4 on the server with + aRFS configured. This example uses TCP over IPv4. + +:: + + # netperf -H <Host IPv4 Address> -t TCP_STREAM + + +Enabling Virtual Functions (VFs) +-------------------------------- +Use sysfs to enable virtual functions (VF). + +For example, you can create 4 VFs as follows:: + + # echo 4 > /sys/class/net/<ethX>/device/sriov_numvfs + +To disable VFs, write 0 to the same file:: + + # echo 0 > /sys/class/net/<ethX>/device/sriov_numvfs + +The maximum number of VFs for the ice driver is 256 total (all ports). To check +how many VFs each PF supports, use the following command:: + + # cat /sys/class/net/<ethX>/device/sriov_totalvfs + +Note: You cannot use SR-IOV when link aggregation (LAG)/bonding is active, and +vice versa. To enforce this, the driver checks for this mutual exclusion. + + +Displaying VF Statistics on the PF +---------------------------------- +Use the following command to display the statistics for the PF and its VFs:: + + # ip -s link show dev <ethX> + +NOTE: The output of this command can be very large due to the maximum number of +possible VFs. + +The PF driver will display a subset of the statistics for the PF and for all +VFs that are configured. The PF will always print a statistics block for each +of the possible VFs, and it will show zero for all unconfigured VFs. + + +Configuring VLAN Tagging on SR-IOV Enabled Adapter Ports +-------------------------------------------------------- +To configure VLAN tagging for the ports on an SR-IOV enabled adapter, use the +following command. The VLAN configuration should be done before the VF driver +is loaded or the VM is booted. The VF is not aware of the VLAN tag being +inserted on transmit and removed on received frames (sometimes called "port +VLAN" mode). + +:: + + # ip link set dev <ethX> vf <id> vlan <vlan id> + +For example, the following will configure PF eth0 and the first VF on VLAN 10:: + + # ip link set dev eth0 vf 0 vlan 10 + + +Enabling a VF link if the port is disconnected +---------------------------------------------- +If the physical function (PF) link is down, you can force link up (from the +host PF) on any virtual functions (VF) bound to the PF. + +For example, to force link up on VF 0 bound to PF eth0:: + + # ip link set eth0 vf 0 state enable + +Note: If the command does not work, it may not be supported by your system. + + +Setting the MAC Address for a VF +-------------------------------- +To change the MAC address for the specified VF:: + + # ip link set <ethX> vf 0 mac <address> + +For example:: + + # ip link set <ethX> vf 0 mac 00:01:02:03:04:05 + +This setting lasts until the PF is reloaded. + +NOTE: Assigning a MAC address for a VF from the host will disable any +subsequent requests to change the MAC address from within the VM. This is a +security feature. The VM is not aware of this restriction, so if this is +attempted in the VM, it will trigger MDD events. + + +Trusted VFs and VF Promiscuous Mode +----------------------------------- +This feature allows you to designate a particular VF as trusted and allows that +trusted VF to request selective promiscuous mode on the Physical Function (PF). + +To set a VF as trusted or untrusted, enter the following command in the +Hypervisor:: + + # ip link set dev <ethX> vf 1 trust [on|off] + +NOTE: It's important to set the VF to trusted before setting promiscuous mode. +If the VM is not trusted, the PF will ignore promiscuous mode requests from the +VF. If the VM becomes trusted after the VF driver is loaded, you must make a +new request to set the VF to promiscuous. + +Once the VF is designated as trusted, use the following commands in the VM to +set the VF to promiscuous mode. + +For promiscuous all:: + + # ip link set <ethX> promisc on + Where <ethX> is a VF interface in the VM + +For promiscuous Multicast:: + + # ip link set <ethX> allmulticast on + Where <ethX> is a VF interface in the VM + +NOTE: By default, the ethtool private flag vf-true-promisc-support is set to +"off," meaning that promiscuous mode for the VF will be limited. To set the +promiscuous mode for the VF to true promiscuous and allow the VF to see all +ingress traffic, use the following command:: + + # ethtool --set-priv-flags <ethX> vf-true-promisc-support on + +The vf-true-promisc-support private flag does not enable promiscuous mode; +rather, it designates which type of promiscuous mode (limited or true) you will +get when you enable promiscuous mode using the ip link commands above. Note +that this is a global setting that affects the entire device. However, the +vf-true-promisc-support private flag is only exposed to the first PF of the +device. The PF remains in limited promiscuous mode regardless of the +vf-true-promisc-support setting. + +Next, add a VLAN interface on the VF interface. For example:: + + # ip link add link eth2 name eth2.100 type vlan id 100 + +Note that the order in which you set the VF to promiscuous mode and add the +VLAN interface does not matter (you can do either first). The result in this +example is that the VF will get all traffic that is tagged with VLAN 100. + + +Malicious Driver Detection (MDD) for VFs +---------------------------------------- +Some Intel Ethernet devices use Malicious Driver Detection (MDD) to detect +malicious traffic from the VF and disable Tx/Rx queues or drop the offending +packet until a VF driver reset occurs. You can view MDD messages in the PF's +system log using the dmesg command. + +- If the PF driver logs MDD events from the VF, confirm that the correct VF + driver is installed. +- To restore functionality, you can manually reload the VF or VM or enable + automatic VF resets. +- When automatic VF resets are enabled, the PF driver will immediately reset + the VF and reenable queues when it detects MDD events on the receive path. +- If automatic VF resets are disabled, the PF will not automatically reset the + VF when it detects MDD events. + +To enable or disable automatic VF resets, use the following command:: + + # ethtool --set-priv-flags <ethX> mdd-auto-reset-vf on|off + + +MAC and VLAN Anti-Spoofing Feature for VFs +------------------------------------------ +When a malicious driver on a Virtual Function (VF) interface attempts to send a +spoofed packet, it is dropped by the hardware and not transmitted. + +NOTE: This feature can be disabled for a specific VF:: + + # ip link set <ethX> vf <vf id> spoofchk {off|on} + + +Jumbo Frames +------------ +Jumbo Frames support is enabled by changing the Maximum Transmission Unit (MTU) +to a value larger than the default value of 1500. + +Use the ifconfig command to increase the MTU size. For example, enter the +following where <ethX> is the interface number:: + + # ifconfig <ethX> mtu 9000 up + +Alternatively, you can use the ip command as follows:: + + # ip link set mtu 9000 dev <ethX> + # ip link set up dev <ethX> + +This setting is not saved across reboots. + + +NOTE: The maximum MTU setting for jumbo frames is 9702. This corresponds to the +maximum jumbo frame size of 9728 bytes. + +NOTE: This driver will attempt to use multiple page sized buffers to receive +each jumbo packet. This should help to avoid buffer starvation issues when +allocating receive packets. + +NOTE: Packet loss may have a greater impact on throughput when you use jumbo +frames. If you observe a drop in performance after enabling jumbo frames, +enabling flow control may mitigate the issue. + + +Speed and Duplex Configuration +------------------------------ +In addressing speed and duplex configuration issues, you need to distinguish +between copper-based adapters and fiber-based adapters. + +In the default mode, an Intel(R) Ethernet Network Adapter using copper +connections will attempt to auto-negotiate with its link partner to determine +the best setting. If the adapter cannot establish link with the link partner +using auto-negotiation, you may need to manually configure the adapter and link +partner to identical settings to establish link and pass packets. This should +only be needed when attempting to link with an older switch that does not +support auto-negotiation or one that has been forced to a specific speed or +duplex mode. Your link partner must match the setting you choose. 1 Gbps speeds +and higher cannot be forced. Use the autonegotiation advertising setting to +manually set devices for 1 Gbps and higher. + +Speed, duplex, and autonegotiation advertising are configured through the +ethtool utility. For the latest version, download and install ethtool from the +following website: + + https://kernel.org/pub/software/network/ethtool/ + +To see the speed configurations your device supports, run the following:: + + # ethtool <ethX> + +Caution: Only experienced network administrators should force speed and duplex +or change autonegotiation advertising manually. The settings at the switch must +always match the adapter settings. Adapter performance may suffer or your +adapter may not operate if you configure the adapter differently from your +switch. + + +Data Center Bridging (DCB) +-------------------------- +NOTE: The kernel assumes that TC0 is available, and will disable Priority Flow +Control (PFC) on the device if TC0 is not available. To fix this, ensure TC0 is +enabled when setting up DCB on your switch. + +DCB is a configuration Quality of Service implementation in hardware. It uses +the VLAN priority tag (802.1p) to filter traffic. That means that there are 8 +different priorities that traffic can be filtered into. It also enables +priority flow control (802.1Qbb) which can limit or eliminate the number of +dropped packets during network stress. Bandwidth can be allocated to each of +these priorities, which is enforced at the hardware level (802.1Qaz). + +DCB is normally configured on the network using the DCBX protocol (802.1Qaz), a +specialization of LLDP (802.1AB). The ice driver supports the following +mutually exclusive variants of DCBX support: + +1) Firmware-based LLDP Agent +2) Software-based LLDP Agent + +In firmware-based mode, firmware intercepts all LLDP traffic and handles DCBX +negotiation transparently for the user. In this mode, the adapter operates in +"willing" DCBX mode, receiving DCB settings from the link partner (typically a +switch). The local user can only query the negotiated DCB configuration. For +information on configuring DCBX parameters on a switch, please consult the +switch manufacturer's documentation. + +In software-based mode, LLDP traffic is forwarded to the network stack and user +space, where a software agent can handle it. In this mode, the adapter can +operate in either "willing" or "nonwilling" DCBX mode and DCB configuration can +be both queried and set locally. This mode requires the FW-based LLDP Agent to +be disabled. + +NOTE: + +- You can enable and disable the firmware-based LLDP Agent using an ethtool + private flag. Refer to the "FW-LLDP (Firmware Link Layer Discovery Protocol)" + section in this README for more information. +- In software-based DCBX mode, you can configure DCB parameters using software + LLDP/DCBX agents that interface with the Linux kernel's DCB Netlink API. We + recommend using OpenLLDP as the DCBX agent when running in software mode. For + more information, see the OpenLLDP man pages and + https://github.com/intel/openlldp. +- The driver implements the DCB netlink interface layer to allow the user space + to communicate with the driver and query DCB configuration for the port. +- iSCSI with DCB is not supported. + + +FW-LLDP (Firmware Link Layer Discovery Protocol) +------------------------------------------------ +Use ethtool to change FW-LLDP settings. The FW-LLDP setting is per port and +persists across boots. + +To enable LLDP:: + + # ethtool --set-priv-flags <ethX> fw-lldp-agent on + +To disable LLDP:: + + # ethtool --set-priv-flags <ethX> fw-lldp-agent off + +To check the current LLDP setting:: + + # ethtool --show-priv-flags <ethX> + +NOTE: You must enable the UEFI HII "LLDP Agent" attribute for this setting to +take effect. If "LLDP AGENT" is set to disabled, you cannot enable it from the +OS. + + +Flow Control +------------ +Ethernet Flow Control (IEEE 802.3x) can be configured with ethtool to enable +receiving and transmitting pause frames for ice. When transmit is enabled, +pause frames are generated when the receive packet buffer crosses a predefined +threshold. When receive is enabled, the transmit unit will halt for the time +delay specified when a pause frame is received. + +NOTE: You must have a flow control capable link partner. + +Flow Control is disabled by default. + +Use ethtool to change the flow control settings. + +To enable or disable Rx or Tx Flow Control:: + + # ethtool -A <ethX> rx <on|off> tx <on|off> + +Note: This command only enables or disables Flow Control if auto-negotiation is +disabled. If auto-negotiation is enabled, this command changes the parameters +used for auto-negotiation with the link partner. + +Note: Flow Control auto-negotiation is part of link auto-negotiation. Depending +on your device, you may not be able to change the auto-negotiation setting. + +NOTE: + +- The ice driver requires flow control on both the port and link partner. If + flow control is disabled on one of the sides, the port may appear to hang on + heavy traffic. +- You may encounter issues with link-level flow control (LFC) after disabling + DCB. The LFC status may show as enabled but traffic is not paused. To resolve + this issue, disable and reenable LFC using ethtool:: + + # ethtool -A <ethX> rx off tx off + # ethtool -A <ethX> rx on tx on + + +NAPI +---- + +This driver supports NAPI (Rx polling mode). + +See :ref:`Documentation/networking/napi.rst <napi>` for more information. + +MACVLAN +------- +This driver supports MACVLAN. Kernel support for MACVLAN can be tested by +checking if the MACVLAN driver is loaded. You can run 'lsmod | grep macvlan' to +see if the MACVLAN driver is loaded or run 'modprobe macvlan' to try to load +the MACVLAN driver. + +NOTE: + +- In passthru mode, you can only set up one MACVLAN device. It will inherit the + MAC address of the underlying PF (Physical Function) device. + + +IEEE 802.1ad (QinQ) Support +--------------------------- +The IEEE 802.1ad standard, informally known as QinQ, allows for multiple VLAN +IDs within a single Ethernet frame. VLAN IDs are sometimes referred to as +"tags," and multiple VLAN IDs are thus referred to as a "tag stack." Tag stacks +allow L2 tunneling and the ability to segregate traffic within a particular +VLAN ID, among other uses. + +NOTES: + +- Receive checksum offloads and VLAN acceleration are not supported for 802.1ad + (QinQ) packets. + +- 0x88A8 traffic will not be received unless VLAN stripping is disabled with + the following command:: + + # ethtool -K <ethX> rxvlan off + +- 0x88A8/0x8100 double VLANs cannot be used with 0x8100 or 0x8100/0x8100 VLANS + configured on the same port. 0x88a8/0x8100 traffic will not be received if + 0x8100 VLANs are configured. + +- The VF can only transmit 0x88A8/0x8100 (i.e., 802.1ad/802.1Q) traffic if: + + 1) The VF is not assigned a port VLAN. + 2) spoofchk is disabled from the PF. If you enable spoofchk, the VF will + not transmit 0x88A8/0x8100 traffic. + +- The VF may not receive all network traffic based on the Inner VLAN header + when VF true promiscuous mode (vf-true-promisc-support) and double VLANs are + enabled in SR-IOV mode. + +The following are examples of how to configure 802.1ad (QinQ):: + + # ip link add link eth0 eth0.24 type vlan proto 802.1ad id 24 + # ip link add link eth0.24 eth0.24.371 type vlan proto 802.1Q id 371 + + Where "24" and "371" are example VLAN IDs. + + +Tunnel/Overlay Stateless Offloads +--------------------------------- +Supported tunnels and overlays include VXLAN, GENEVE, and others depending on +hardware and software configuration. Stateless offloads are enabled by default. + +To view the current state of all offloads:: + + # ethtool -k <ethX> + + +UDP Segmentation Offload +------------------------ +Allows the adapter to offload transmit segmentation of UDP packets with +payloads up to 64K into valid Ethernet frames. Because the adapter hardware is +able to complete data segmentation much faster than operating system software, +this feature may improve transmission performance. +In addition, the adapter may use fewer CPU resources. + +NOTE: + +- The application sending UDP packets must support UDP segmentation offload. + +To enable/disable UDP Segmentation Offload, issue the following command:: + + # ethtool -K <ethX> tx-udp-segmentation [off|on] + + +GNSS module +----------- +Requires kernel compiled with CONFIG_GNSS=y or CONFIG_GNSS=m. +Allows user to read messages from the GNSS hardware module and write supported +commands. If the module is physically present, a GNSS device is spawned: +``/dev/gnss<id>``. +The protocol of write command is dependent on the GNSS hardware module as the +driver writes raw bytes by the GNSS object to the receiver through i2c. Please +refer to the hardware GNSS module documentation for configuration details. + + +Performance Optimization +======================== +Driver defaults are meant to fit a wide variety of workloads, but if further +optimization is required, we recommend experimenting with the following +settings. + + +Rx Descriptor Ring Size +----------------------- +To reduce the number of Rx packet discards, increase the number of Rx +descriptors for each Rx ring using ethtool. + + Check if the interface is dropping Rx packets due to buffers being full + (rx_dropped.nic can mean that there is no PCIe bandwidth):: + + # ethtool -S <ethX> | grep "rx_dropped" + + If the previous command shows drops on queues, it may help to increase + the number of descriptors using 'ethtool -G':: + + # ethtool -G <ethX> rx <N> + Where <N> is the desired number of ring entries/descriptors + + This can provide temporary buffering for issues that create latency while + the CPUs process descriptors. + + +Interrupt Rate Limiting +----------------------- +This driver supports an adaptive interrupt throttle rate (ITR) mechanism that +is tuned for general workloads. The user can customize the interrupt rate +control for specific workloads, via ethtool, adjusting the number of +microseconds between interrupts. + +To set the interrupt rate manually, you must disable adaptive mode:: + + # ethtool -C <ethX> adaptive-rx off adaptive-tx off + +For lower CPU utilization: + + Disable adaptive ITR and lower Rx and Tx interrupts. The examples below + affect every queue of the specified interface. + + Setting rx-usecs and tx-usecs to 80 will limit interrupts to about + 12,500 interrupts per second per queue:: + + # ethtool -C <ethX> adaptive-rx off adaptive-tx off rx-usecs 80 tx-usecs 80 + +For reduced latency: + + Disable adaptive ITR and ITR by setting rx-usecs and tx-usecs to 0 + using ethtool:: + + # ethtool -C <ethX> adaptive-rx off adaptive-tx off rx-usecs 0 tx-usecs 0 + +Per-queue interrupt rate settings: + + The following examples are for queues 1 and 3, but you can adjust other + queues. + + To disable Rx adaptive ITR and set static Rx ITR to 10 microseconds or + about 100,000 interrupts/second, for queues 1 and 3:: + + # ethtool --per-queue <ethX> queue_mask 0xa --coalesce adaptive-rx off + rx-usecs 10 + + To show the current coalesce settings for queues 1 and 3:: + + # ethtool --per-queue <ethX> queue_mask 0xa --show-coalesce + +Bounding interrupt rates using rx-usecs-high: + + :Valid Range: 0-236 (0=no limit) + + The range of 0-236 microseconds provides an effective range of 4,237 to + 250,000 interrupts per second. The value of rx-usecs-high can be set + independently of rx-usecs and tx-usecs in the same ethtool command, and is + also independent of the adaptive interrupt moderation algorithm. The + underlying hardware supports granularity in 4-microsecond intervals, so + adjacent values may result in the same interrupt rate. + + The following command would disable adaptive interrupt moderation, and allow + a maximum of 5 microseconds before indicating a receive or transmit was + complete. However, instead of resulting in as many as 200,000 interrupts per + second, it limits total interrupts per second to 50,000 via the rx-usecs-high + parameter. + + :: + + # ethtool -C <ethX> adaptive-rx off adaptive-tx off rx-usecs-high 20 + rx-usecs 5 tx-usecs 5 + + +Virtualized Environments +------------------------ +In addition to the other suggestions in this section, the following may be +helpful to optimize performance in VMs. + + Using the appropriate mechanism (vcpupin) in the VM, pin the CPUs to + individual LCPUs, making sure to use a set of CPUs included in the + device's local_cpulist: ``/sys/class/net/<ethX>/device/local_cpulist``. + + Configure as many Rx/Tx queues in the VM as available. (See the iavf driver + documentation for the number of queues supported.) For example:: + + # ethtool -L <virt_interface> rx <max> tx <max> + + +Support +======= +For general information, go to the Intel support website at: +https://www.intel.com/support/ + +If an issue is identified with the released source code on a supported kernel +with a supported adapter, email the specific information related to the issue +to intel-wired-lan@lists.osuosl.org. + + +Trademarks +========== +Intel is a trademark or registered trademark of Intel Corporation or its +subsidiaries in the United States and/or other countries. + +* Other names and brands may be claimed as the property of others. diff --git a/Documentation/networking/device_drivers/ethernet/intel/igb.rst b/Documentation/networking/device_drivers/ethernet/intel/igb.rst new file mode 100644 index 0000000000..fbd590b6a0 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/intel/igb.rst @@ -0,0 +1,208 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +========================================================== +Linux Base Driver for Intel(R) Ethernet Network Connection +========================================================== + +Intel Gigabit Linux driver. +Copyright(c) 1999-2018 Intel Corporation. + +Contents +======== + +- Identifying Your Adapter +- Command Line Parameters +- Additional Configurations +- Support + + +Identifying Your Adapter +======================== +For information on how to identify your adapter, and for the latest Intel +network drivers, refer to the Intel Support website: +https://www.intel.com/support + + +Command Line Parameters +======================== +If the driver is built as a module, the following optional parameters are used +by entering them on the command line with the modprobe command using this +syntax:: + + modprobe igb [<option>=<VAL1>,<VAL2>,...] + +There needs to be a <VAL#> for each network port in the system supported by +this driver. The values will be applied to each instance, in function order. +For example:: + + modprobe igb max_vfs=2,4 + +In this case, there are two network ports supported by igb in the system. + +NOTE: A descriptor describes a data buffer and attributes related to the data +buffer. This information is accessed by the hardware. + +max_vfs +------- +:Valid Range: 0-7 + +This parameter adds support for SR-IOV. It causes the driver to spawn up to +max_vfs worth of virtual functions. If the value is greater than 0 it will +also force the VMDq parameter to be 1 or more. + +The parameters for the driver are referenced by position. Thus, if you have a +dual port adapter, or more than one adapter in your system, and want N virtual +functions per port, you must specify a number for each port with each parameter +separated by a comma. For example:: + + modprobe igb max_vfs=4 + +This will spawn 4 VFs on the first port. + +:: + + modprobe igb max_vfs=2,4 + +This will spawn 2 VFs on the first port and 4 VFs on the second port. + +NOTE: Caution must be used in loading the driver with these parameters. +Depending on your system configuration, number of slots, etc., it is impossible +to predict in all cases where the positions would be on the command line. + +NOTE: Neither the device nor the driver control how VFs are mapped into config +space. Bus layout will vary by operating system. On operating systems that +support it, you can check sysfs to find the mapping. + +NOTE: When either SR-IOV mode or VMDq mode is enabled, hardware VLAN filtering +and VLAN tag stripping/insertion will remain enabled. Please remove the old +VLAN filter before the new VLAN filter is added. For example:: + + ip link set eth0 vf 0 vlan 100 // set vlan 100 for VF 0 + ip link set eth0 vf 0 vlan 0 // Delete vlan 100 + ip link set eth0 vf 0 vlan 200 // set a new vlan 200 for VF 0 + +Debug +----- +:Valid Range: 0-16 (0=none,...,16=all) +:Default Value: 0 + +This parameter adjusts the level debug messages displayed in the system logs. + + +Additional Features and Configurations +====================================== + +Jumbo Frames +------------ +Jumbo Frames support is enabled by changing the Maximum Transmission Unit (MTU) +to a value larger than the default value of 1500. + +Use the ifconfig command to increase the MTU size. For example, enter the +following where <x> is the interface number:: + + ifconfig eth<x> mtu 9000 up + +Alternatively, you can use the ip command as follows:: + + ip link set mtu 9000 dev eth<x> + ip link set up dev eth<x> + +This setting is not saved across reboots. The setting change can be made +permanent by adding 'MTU=9000' to the file: + +- For RHEL: /etc/sysconfig/network-scripts/ifcfg-eth<x> +- For SLES: /etc/sysconfig/network/<config_file> + +NOTE: The maximum MTU setting for Jumbo Frames is 9216. This value coincides +with the maximum Jumbo Frames size of 9234 bytes. + +NOTE: Using Jumbo frames at 10 or 100 Mbps is not supported and may result in +poor performance or loss of link. + + +ethtool +------- +The driver utilizes the ethtool interface for driver configuration and +diagnostics, as well as displaying statistical information. The latest ethtool +version is required for this functionality. Download it at: + +https://www.kernel.org/pub/software/network/ethtool/ + + +Enabling Wake on LAN (WoL) +-------------------------- +WoL is configured through the ethtool utility. + +WoL will be enabled on the system during the next shut down or reboot. For +this driver version, in order to enable WoL, the igb driver must be loaded +prior to shutting down or suspending the system. + +NOTE: Wake on LAN is only supported on port A of multi-port devices. Also +Wake On LAN is not supported for the following device: +- Intel(R) Gigabit VT Quad Port Server Adapter + + +Multiqueue +---------- +In this mode, a separate MSI-X vector is allocated for each queue and one for +"other" interrupts such as link status change and errors. All interrupts are +throttled via interrupt moderation. Interrupt moderation must be used to avoid +interrupt storms while the driver is processing one interrupt. The moderation +value should be at least as large as the expected time for the driver to +process an interrupt. Multiqueue is off by default. + +REQUIREMENTS: MSI-X support is required for Multiqueue. If MSI-X is not found, +the system will fallback to MSI or to Legacy interrupts. This driver supports +receive multiqueue on all kernels that support MSI-X. + +NOTE: On some kernels a reboot is required to switch between single queue mode +and multiqueue mode or vice-versa. + + +MAC and VLAN anti-spoofing feature +---------------------------------- +When a malicious driver attempts to send a spoofed packet, it is dropped by the +hardware and not transmitted. + +An interrupt is sent to the PF driver notifying it of the spoof attempt. When a +spoofed packet is detected, the PF driver will send the following message to +the system log (displayed by the "dmesg" command): +Spoof event(s) detected on VF(n), where n = the VF that attempted to do the +spoofing + + +Setting MAC Address, VLAN and Rate Limit Using IProute2 Tool +------------------------------------------------------------ +You can set a MAC address of a Virtual Function (VF), a default VLAN and the +rate limit using the IProute2 tool. Download the latest version of the +IProute2 tool from Sourceforge if your version does not have all the features +you require. + +Credit Based Shaper (Qav Mode) +------------------------------ +When enabling the CBS qdisc in the hardware offload mode, traffic shaping using +the CBS (described in the IEEE 802.1Q-2018 Section 8.6.8.2 and discussed in the +Annex L) algorithm will run in the i210 controller, so it's more accurate and +uses less CPU. + +When using offloaded CBS, and the traffic rate obeys the configured rate +(doesn't go above it), CBS should have little to no effect in the latency. + +The offloaded version of the algorithm has some limits, caused by how the idle +slope is expressed in the adapter's registers. It can only represent idle slopes +in 16.38431 kbps units, which means that if a idle slope of 2576kbps is +requested, the controller will be configured to use a idle slope of ~2589 kbps, +because the driver rounds the value up. For more details, see the comments on +:c:func:`igb_config_tx_modes()`. + +NOTE: This feature is exclusive to i210 models. + + +Support +======= +For general information, go to the Intel support website at: +https://www.intel.com/support/ + +If an issue is identified with the released source code on a supported kernel +with a supported adapter, email the specific information related to the issue +to intel-wired-lan@lists.osuosl.org. diff --git a/Documentation/networking/device_drivers/ethernet/intel/igbvf.rst b/Documentation/networking/device_drivers/ethernet/intel/igbvf.rst new file mode 100644 index 0000000000..11a9017f30 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/intel/igbvf.rst @@ -0,0 +1,60 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +=========================================================== +Linux Base Virtual Function Driver for Intel(R) 1G Ethernet +=========================================================== + +Intel Gigabit Virtual Function Linux driver. +Copyright(c) 1999-2018 Intel Corporation. + +Contents +======== +- Identifying Your Adapter +- Additional Configurations +- Support + +This driver supports Intel 82576-based virtual function devices-based virtual +function devices that can only be activated on kernels that support SR-IOV. + +SR-IOV requires the correct platform and OS support. + +The guest OS loading this driver must support MSI-X interrupts. + +For questions related to hardware requirements, refer to the documentation +supplied with your Intel adapter. All hardware requirements listed apply to use +with Linux. + +Driver information can be obtained using ethtool, lspci, and ifconfig. +Instructions on updating ethtool can be found in the section Additional +Configurations later in this document. + +NOTE: There is a limit of a total of 32 shared VLANs to 1 or more VFs. + + +Identifying Your Adapter +======================== +For information on how to identify your adapter, and for the latest Intel +network drivers, refer to the Intel Support website: +https://www.intel.com/support + + +Additional Features and Configurations +====================================== + +ethtool +------- +The driver utilizes the ethtool interface for driver configuration and +diagnostics, as well as displaying statistical information. The latest ethtool +version is required for this functionality. Download it at: + +https://www.kernel.org/pub/software/network/ethtool/ + + +Support +======= +For general information, go to the Intel support website at: +https://www.intel.com/support/ + +If an issue is identified with the released source code on a supported kernel +with a supported adapter, email the specific information related to the issue +to intel-wired-lan@lists.osuosl.org. diff --git a/Documentation/networking/device_drivers/ethernet/intel/ixgbe.rst b/Documentation/networking/device_drivers/ethernet/intel/ixgbe.rst new file mode 100644 index 0000000000..1e5f16993f --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/intel/ixgbe.rst @@ -0,0 +1,552 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +=========================================================================== +Linux Base Driver for the Intel(R) Ethernet 10 Gigabit PCI Express Adapters +=========================================================================== + +Intel 10 Gigabit Linux driver. +Copyright(c) 1999-2018 Intel Corporation. + +Contents +======== + +- Identifying Your Adapter +- Command Line Parameters +- Additional Configurations +- Known Issues +- Support + +Identifying Your Adapter +======================== +The driver is compatible with devices based on the following: + + * Intel(R) Ethernet Controller 82598 + * Intel(R) Ethernet Controller 82599 + * Intel(R) Ethernet Controller X520 + * Intel(R) Ethernet Controller X540 + * Intel(R) Ethernet Controller x550 + * Intel(R) Ethernet Controller X552 + * Intel(R) Ethernet Controller X553 + +For information on how to identify your adapter, and for the latest Intel +network drivers, refer to the Intel Support website: +https://www.intel.com/support + +SFP+ Devices with Pluggable Optics +---------------------------------- + +82599-BASED ADAPTERS +~~~~~~~~~~~~~~~~~~~~ +NOTES: +- If your 82599-based Intel(R) Network Adapter came with Intel optics or is an +Intel(R) Ethernet Server Adapter X520-2, then it only supports Intel optics +and/or the direct attach cables listed below. +- When 82599-based SFP+ devices are connected back to back, they should be set +to the same Speed setting via ethtool. Results may vary if you mix speed +settings. + ++---------------+---------------------------------------+------------------+ +| Supplier | Type | Part Numbers | ++===============+=======================================+==================+ +| SR Modules | ++---------------+---------------------------------------+------------------+ +| Intel | DUAL RATE 1G/10G SFP+ SR (bailed) | FTLX8571D3BCV-IT | ++---------------+---------------------------------------+------------------+ +| Intel | DUAL RATE 1G/10G SFP+ SR (bailed) | AFBR-703SDZ-IN2 | ++---------------+---------------------------------------+------------------+ +| Intel | DUAL RATE 1G/10G SFP+ SR (bailed) | AFBR-703SDDZ-IN1 | ++---------------+---------------------------------------+------------------+ +| LR Modules | ++---------------+---------------------------------------+------------------+ +| Intel | DUAL RATE 1G/10G SFP+ LR (bailed) | FTLX1471D3BCV-IT | ++---------------+---------------------------------------+------------------+ +| Intel | DUAL RATE 1G/10G SFP+ LR (bailed) | AFCT-701SDZ-IN2 | ++---------------+---------------------------------------+------------------+ +| Intel | DUAL RATE 1G/10G SFP+ LR (bailed) | AFCT-701SDDZ-IN1 | ++---------------+---------------------------------------+------------------+ + +The following is a list of 3rd party SFP+ modules that have received some +testing. Not all modules are applicable to all devices. + ++---------------+---------------------------------------+------------------+ +| Supplier | Type | Part Numbers | ++===============+=======================================+==================+ +| Finisar | SFP+ SR bailed, 10g single rate | FTLX8571D3BCL | ++---------------+---------------------------------------+------------------+ +| Avago | SFP+ SR bailed, 10g single rate | AFBR-700SDZ | ++---------------+---------------------------------------+------------------+ +| Finisar | SFP+ LR bailed, 10g single rate | FTLX1471D3BCL | ++---------------+---------------------------------------+------------------+ +| Finisar | DUAL RATE 1G/10G SFP+ SR (No Bail) | FTLX8571D3QCV-IT | ++---------------+---------------------------------------+------------------+ +| Avago | DUAL RATE 1G/10G SFP+ SR (No Bail) | AFBR-703SDZ-IN1 | ++---------------+---------------------------------------+------------------+ +| Finisar | DUAL RATE 1G/10G SFP+ LR (No Bail) | FTLX1471D3QCV-IT | ++---------------+---------------------------------------+------------------+ +| Avago | DUAL RATE 1G/10G SFP+ LR (No Bail) | AFCT-701SDZ-IN1 | ++---------------+---------------------------------------+------------------+ +| Finisar | 1000BASE-T SFP | FCLF8522P2BTL | ++---------------+---------------------------------------+------------------+ +| Avago | 1000BASE-T | ABCU-5710RZ | ++---------------+---------------------------------------+------------------+ +| HP | 1000BASE-SX SFP | 453153-001 | ++---------------+---------------------------------------+------------------+ + +82599-based adapters support all passive and active limiting direct attach +cables that comply with SFF-8431 v4.1 and SFF-8472 v10.4 specifications. + +Laser turns off for SFP+ when ifconfig ethX down +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +"ifconfig ethX down" turns off the laser for 82599-based SFP+ fiber adapters. +"ifconfig ethX up" turns on the laser. +Alternatively, you can use "ip link set [down/up] dev ethX" to turn the +laser off and on. + + +82599-based QSFP+ Adapters +~~~~~~~~~~~~~~~~~~~~~~~~~~ +NOTES: +- If your 82599-based Intel(R) Network Adapter came with Intel optics, it only +supports Intel optics. +- 82599-based QSFP+ adapters only support 4x10 Gbps connections. 1x40 Gbps +connections are not supported. QSFP+ link partners must be configured for +4x10 Gbps. +- 82599-based QSFP+ adapters do not support automatic link speed detection. +The link speed must be configured to either 10 Gbps or 1 Gbps to match the link +partners speed capabilities. Incorrect speed configurations will result in +failure to link. +- Intel(R) Ethernet Converged Network Adapter X520-Q1 only supports the optics +and direct attach cables listed below. + ++---------------+---------------------------------------+------------------+ +| Supplier | Type | Part Numbers | ++===============+=======================================+==================+ +| Intel | DUAL RATE 1G/10G QSFP+ SRL (bailed) | E10GQSFPSR | ++---------------+---------------------------------------+------------------+ + +82599-based QSFP+ adapters support all passive and active limiting QSFP+ +direct attach cables that comply with SFF-8436 v4.1 specifications. + +82598-BASED ADAPTERS +~~~~~~~~~~~~~~~~~~~~ +NOTES: +- Intel(r) Ethernet Network Adapters that support removable optical modules +only support their original module type (for example, the Intel(R) 10 Gigabit +SR Dual Port Express Module only supports SR optical modules). If you plug in +a different type of module, the driver will not load. +- Hot Swapping/hot plugging optical modules is not supported. +- Only single speed, 10 gigabit modules are supported. +- LAN on Motherboard (LOMs) may support DA, SR, or LR modules. Other module +types are not supported. Please see your system documentation for details. + +The following is a list of SFP+ modules and direct attach cables that have +received some testing. Not all modules are applicable to all devices. + ++---------------+---------------------------------------+------------------+ +| Supplier | Type | Part Numbers | ++===============+=======================================+==================+ +| Finisar | SFP+ SR bailed, 10g single rate | FTLX8571D3BCL | ++---------------+---------------------------------------+------------------+ +| Avago | SFP+ SR bailed, 10g single rate | AFBR-700SDZ | ++---------------+---------------------------------------+------------------+ +| Finisar | SFP+ LR bailed, 10g single rate | FTLX1471D3BCL | ++---------------+---------------------------------------+------------------+ + +82598-based adapters support all passive direct attach cables that comply with +SFF-8431 v4.1 and SFF-8472 v10.4 specifications. Active direct attach cables +are not supported. + +Third party optic modules and cables referred to above are listed only for the +purpose of highlighting third party specifications and potential +compatibility, and are not recommendations or endorsements or sponsorship of +any third party's product by Intel. Intel is not endorsing or promoting +products made by any third party and the third party reference is provided +only to share information regarding certain optic modules and cables with the +above specifications. There may be other manufacturers or suppliers, producing +or supplying optic modules and cables with similar or matching descriptions. +Customers must use their own discretion and diligence to purchase optic +modules and cables from any third party of their choice. Customers are solely +responsible for assessing the suitability of the product and/or devices and +for the selection of the vendor for purchasing any product. THE OPTIC MODULES +AND CABLES REFERRED TO ABOVE ARE NOT WARRANTED OR SUPPORTED BY INTEL. INTEL +ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED +WARRANTY, RELATING TO SALE AND/OR USE OF SUCH THIRD PARTY PRODUCTS OR +SELECTION OF VENDOR BY CUSTOMERS. + +Command Line Parameters +======================= + +max_vfs +------- +:Valid Range: 1-63 + +This parameter adds support for SR-IOV. It causes the driver to spawn up to +max_vfs worth of virtual functions. +If the value is greater than 0 it will also force the VMDq parameter to be 1 or +more. + +NOTE: This parameter is only used on kernel 3.7.x and below. On kernel 3.8.x +and above, use sysfs to enable VFs. Also, for Red Hat distributions, this +parameter is only used on version 6.6 and older. For version 6.7 and newer, use +sysfs. For example:: + + #echo $num_vf_enabled > /sys/class/net/$dev/device/sriov_numvfs // enable VFs + #echo 0 > /sys/class/net/$dev/device/sriov_numvfs //disable VFs + +The parameters for the driver are referenced by position. Thus, if you have a +dual port adapter, or more than one adapter in your system, and want N virtual +functions per port, you must specify a number for each port with each parameter +separated by a comma. For example:: + + modprobe ixgbe max_vfs=4 + +This will spawn 4 VFs on the first port. + +:: + + modprobe ixgbe max_vfs=2,4 + +This will spawn 2 VFs on the first port and 4 VFs on the second port. + +NOTE: Caution must be used in loading the driver with these parameters. +Depending on your system configuration, number of slots, etc., it is impossible +to predict in all cases where the positions would be on the command line. + +NOTE: Neither the device nor the driver control how VFs are mapped into config +space. Bus layout will vary by operating system. On operating systems that +support it, you can check sysfs to find the mapping. + +NOTE: When either SR-IOV mode or VMDq mode is enabled, hardware VLAN filtering +and VLAN tag stripping/insertion will remain enabled. Please remove the old +VLAN filter before the new VLAN filter is added. For example, + +:: + + ip link set eth0 vf 0 vlan 100 // set VLAN 100 for VF 0 + ip link set eth0 vf 0 vlan 0 // Delete VLAN 100 + ip link set eth0 vf 0 vlan 200 // set a new VLAN 200 for VF 0 + +With kernel 3.6, the driver supports the simultaneous usage of max_vfs and DCB +features, subject to the constraints described below. Prior to kernel 3.6, the +driver did not support the simultaneous operation of max_vfs greater than 0 and +the DCB features (multiple traffic classes utilizing Priority Flow Control and +Extended Transmission Selection). + +When DCB is enabled, network traffic is transmitted and received through +multiple traffic classes (packet buffers in the NIC). The traffic is associated +with a specific class based on priority, which has a value of 0 through 7 used +in the VLAN tag. When SR-IOV is not enabled, each traffic class is associated +with a set of receive/transmit descriptor queue pairs. The number of queue +pairs for a given traffic class depends on the hardware configuration. When +SR-IOV is enabled, the descriptor queue pairs are grouped into pools. The +Physical Function (PF) and each Virtual Function (VF) is allocated a pool of +receive/transmit descriptor queue pairs. When multiple traffic classes are +configured (for example, DCB is enabled), each pool contains a queue pair from +each traffic class. When a single traffic class is configured in the hardware, +the pools contain multiple queue pairs from the single traffic class. + +The number of VFs that can be allocated depends on the number of traffic +classes that can be enabled. The configurable number of traffic classes for +each enabled VF is as follows: +0 - 15 VFs = Up to 8 traffic classes, depending on device support +16 - 31 VFs = Up to 4 traffic classes +32 - 63 VFs = 1 traffic class + +When VFs are configured, the PF is allocated one pool as well. The PF supports +the DCB features with the constraint that each traffic class will only use a +single queue pair. When zero VFs are configured, the PF can support multiple +queue pairs per traffic class. + +allow_unsupported_sfp +--------------------- +:Valid Range: 0,1 +:Default Value: 0 (disabled) + +This parameter allows unsupported and untested SFP+ modules on 82599-based +adapters, as long as the type of module is known to the driver. + +debug +----- +:Valid Range: 0-16 (0=none,...,16=all) +:Default Value: 0 + +This parameter adjusts the level of debug messages displayed in the system +logs. + + +Additional Features and Configurations +====================================== + +Flow Control +------------ +Ethernet Flow Control (IEEE 802.3x) can be configured with ethtool to enable +receiving and transmitting pause frames for ixgbe. When transmit is enabled, +pause frames are generated when the receive packet buffer crosses a predefined +threshold. When receive is enabled, the transmit unit will halt for the time +delay specified when a pause frame is received. + +NOTE: You must have a flow control capable link partner. + +Flow Control is enabled by default. + +Use ethtool to change the flow control settings. To enable or disable Rx or +Tx Flow Control:: + + ethtool -A eth? rx <on|off> tx <on|off> + +Note: This command only enables or disables Flow Control if auto-negotiation is +disabled. If auto-negotiation is enabled, this command changes the parameters +used for auto-negotiation with the link partner. + +To enable or disable auto-negotiation:: + + ethtool -s eth? autoneg <on|off> + +Note: Flow Control auto-negotiation is part of link auto-negotiation. Depending +on your device, you may not be able to change the auto-negotiation setting. + +NOTE: For 82598 backplane cards entering 1 gigabit mode, flow control default +behavior is changed to off. Flow control in 1 gigabit mode on these devices can +lead to transmit hangs. + +Intel(R) Ethernet Flow Director +------------------------------- +The Intel Ethernet Flow Director performs the following tasks: + +- Directs receive packets according to their flows to different queues. +- Enables tight control on routing a flow in the platform. +- Matches flows and CPU cores for flow affinity. +- Supports multiple parameters for flexible flow classification and load + balancing (in SFP mode only). + +NOTE: Intel Ethernet Flow Director masking works in the opposite manner from +subnet masking. In the following command:: + + #ethtool -N eth11 flow-type ip4 src-ip 172.4.1.2 m 255.0.0.0 dst-ip \ + 172.21.1.1 m 255.128.0.0 action 31 + +The src-ip value that is written to the filter will be 0.4.1.2, not 172.0.0.0 +as might be expected. Similarly, the dst-ip value written to the filter will be +0.21.1.1, not 172.0.0.0. + +To enable or disable the Intel Ethernet Flow Director:: + + # ethtool -K ethX ntuple <on|off> + +When disabling ntuple filters, all the user programmed filters are flushed from +the driver cache and hardware. All needed filters must be re-added when ntuple +is re-enabled. + +To add a filter that directs packet to queue 2, use -U or -N switch:: + + # ethtool -N ethX flow-type tcp4 src-ip 192.168.10.1 dst-ip \ + 192.168.10.2 src-port 2000 dst-port 2001 action 2 [loc 1] + +To see the list of filters currently present:: + + # ethtool <-u|-n> ethX + +Sideband Perfect Filters +------------------------ +Sideband Perfect Filters are used to direct traffic that matches specified +characteristics. They are enabled through ethtool's ntuple interface. To add a +new filter use the following command:: + + ethtool -U <device> flow-type <type> src-ip <ip> dst-ip <ip> src-port <port> \ + dst-port <port> action <queue> + +Where: + <device> - the ethernet device to program + <type> - can be ip4, tcp4, udp4, or sctp4 + <ip> - the IP address to match on + <port> - the port number to match on + <queue> - the queue to direct traffic towards (-1 discards the matched traffic) + +Use the following command to delete a filter:: + + ethtool -U <device> delete <N> + +Where <N> is the filter id displayed when printing all the active filters, and +may also have been specified using "loc <N>" when adding the filter. + +The following example matches TCP traffic sent from 192.168.0.1, port 5300, +directed to 192.168.0.5, port 80, and sends it to queue 7:: + + ethtool -U enp130s0 flow-type tcp4 src-ip 192.168.0.1 dst-ip 192.168.0.5 \ + src-port 5300 dst-port 80 action 7 + +For each flow-type, the programmed filters must all have the same matching +input set. For example, issuing the following two commands is acceptable:: + + ethtool -U enp130s0 flow-type ip4 src-ip 192.168.0.1 src-port 5300 action 7 + ethtool -U enp130s0 flow-type ip4 src-ip 192.168.0.5 src-port 55 action 10 + +Issuing the next two commands, however, is not acceptable, since the first +specifies src-ip and the second specifies dst-ip:: + + ethtool -U enp130s0 flow-type ip4 src-ip 192.168.0.1 src-port 5300 action 7 + ethtool -U enp130s0 flow-type ip4 dst-ip 192.168.0.5 src-port 55 action 10 + +The second command will fail with an error. You may program multiple filters +with the same fields, using different values, but, on one device, you may not +program two TCP4 filters with different matching fields. + +Matching on a sub-portion of a field is not supported by the ixgbe driver, thus +partial mask fields are not supported. + +To create filters that direct traffic to a specific Virtual Function, use the +"user-def" parameter. Specify the user-def as a 64 bit value, where the lower 32 +bits represents the queue number, while the next 8 bits represent which VF. +Note that 0 is the PF, so the VF identifier is offset by 1. For example:: + + ... user-def 0x800000002 ... + +specifies to direct traffic to Virtual Function 7 (8 minus 1) into queue 2 of +that VF. + +Note that these filters will not break internal routing rules, and will not +route traffic that otherwise would not have been sent to the specified Virtual +Function. + +Jumbo Frames +------------ +Jumbo Frames support is enabled by changing the Maximum Transmission Unit (MTU) +to a value larger than the default value of 1500. + +Use the ifconfig command to increase the MTU size. For example, enter the +following where <x> is the interface number:: + + ifconfig eth<x> mtu 9000 up + +Alternatively, you can use the ip command as follows:: + + ip link set mtu 9000 dev eth<x> + ip link set up dev eth<x> + +This setting is not saved across reboots. The setting change can be made +permanent by adding 'MTU=9000' to the file:: + + /etc/sysconfig/network-scripts/ifcfg-eth<x> // for RHEL + /etc/sysconfig/network/<config_file> // for SLES + +NOTE: The maximum MTU setting for Jumbo Frames is 9710. This value coincides +with the maximum Jumbo Frames size of 9728 bytes. + +NOTE: This driver will attempt to use multiple page sized buffers to receive +each jumbo packet. This should help to avoid buffer starvation issues when +allocating receive packets. + +NOTE: For 82599-based network connections, if you are enabling jumbo frames in +a virtual function (VF), jumbo frames must first be enabled in the physical +function (PF). The VF MTU setting cannot be larger than the PF MTU. + +NBASE-T Support +--------------- +The ixgbe driver supports NBASE-T on some devices. However, the advertisement +of NBASE-T speeds is suppressed by default, to accommodate broken network +switches which cannot cope with advertised NBASE-T speeds. Use the ethtool +command to enable advertising NBASE-T speeds on devices which support it:: + + ethtool -s eth? advertise 0x1800000001028 + +On Linux systems with INTERFACES(5), this can be specified as a pre-up command +in /etc/network/interfaces so that the interface is always brought up with +NBASE-T support, e.g.:: + + iface eth? inet dhcp + pre-up ethtool -s eth? advertise 0x1800000001028 || true + +Generic Receive Offload, aka GRO +-------------------------------- +The driver supports the in-kernel software implementation of GRO. GRO has +shown that by coalescing Rx traffic into larger chunks of data, CPU +utilization can be significantly reduced when under large Rx load. GRO is an +evolution of the previously-used LRO interface. GRO is able to coalesce +other protocols besides TCP. It's also safe to use with configurations that +are problematic for LRO, namely bridging and iSCSI. + +Data Center Bridging (DCB) +-------------------------- +NOTE: +The kernel assumes that TC0 is available, and will disable Priority Flow +Control (PFC) on the device if TC0 is not available. To fix this, ensure TC0 is +enabled when setting up DCB on your switch. + +DCB is a configuration Quality of Service implementation in hardware. It uses +the VLAN priority tag (802.1p) to filter traffic. That means that there are 8 +different priorities that traffic can be filtered into. It also enables +priority flow control (802.1Qbb) which can limit or eliminate the number of +dropped packets during network stress. Bandwidth can be allocated to each of +these priorities, which is enforced at the hardware level (802.1Qaz). + +Adapter firmware implements LLDP and DCBX protocol agents as per 802.1AB and +802.1Qaz respectively. The firmware based DCBX agent runs in willing mode only +and can accept settings from a DCBX capable peer. Software configuration of +DCBX parameters via dcbtool/lldptool are not supported. + +The ixgbe driver implements the DCB netlink interface layer to allow user-space +to communicate with the driver and query DCB configuration for the port. + +ethtool +------- +The driver utilizes the ethtool interface for driver configuration and +diagnostics, as well as displaying statistical information. The latest ethtool +version is required for this functionality. Download it at: +https://www.kernel.org/pub/software/network/ethtool/ + +FCoE +---- +The ixgbe driver supports Fiber Channel over Ethernet (FCoE) and Data Center +Bridging (DCB). This code has no default effect on the regular driver +operation. Configuring DCB and FCoE is outside the scope of this README. Refer +to http://www.open-fcoe.org/ for FCoE project information and contact +ixgbe-eedc@lists.sourceforge.net for DCB information. + +MAC and VLAN anti-spoofing feature +---------------------------------- +When a malicious driver attempts to send a spoofed packet, it is dropped by the +hardware and not transmitted. + +An interrupt is sent to the PF driver notifying it of the spoof attempt. When a +spoofed packet is detected, the PF driver will send the following message to +the system log (displayed by the "dmesg" command):: + + ixgbe ethX: ixgbe_spoof_check: n spoofed packets detected + +where "x" is the PF interface number; and "n" is number of spoofed packets. +NOTE: This feature can be disabled for a specific Virtual Function (VF):: + + ip link set <pf dev> vf <vf id> spoofchk {off|on} + +IPsec Offload +------------- +The ixgbe driver supports IPsec Hardware Offload. When creating Security +Associations with "ip xfrm ..." the 'offload' tag option can be used to +register the IPsec SA with the driver in order to get higher throughput in +the secure communications. + +The offload is also supported for ixgbe's VFs, but the VF must be set as +'trusted' and the support must be enabled with:: + + ethtool --set-priv-flags eth<x> vf-ipsec on + ip link set eth<x> vf <y> trust on + + +Known Issues/Troubleshooting +============================ + +Enabling SR-IOV in a 64-bit Microsoft Windows Server 2012/R2 guest OS +--------------------------------------------------------------------- +Linux KVM Hypervisor/VMM supports direct assignment of a PCIe device to a VM. +This includes traditional PCIe devices, as well as SR-IOV-capable devices based +on the Intel Ethernet Controller XL710. + + +Support +======= +For general information, go to the Intel support website at: +https://www.intel.com/support/ + +If an issue is identified with the released source code on a supported kernel +with a supported adapter, email the specific information related to the issue +to intel-wired-lan@lists.osuosl.org. diff --git a/Documentation/networking/device_drivers/ethernet/intel/ixgbevf.rst b/Documentation/networking/device_drivers/ethernet/intel/ixgbevf.rst new file mode 100644 index 0000000000..08dc0d368a --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/intel/ixgbevf.rst @@ -0,0 +1,62 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +============================================================ +Linux Base Virtual Function Driver for Intel(R) 10G Ethernet +============================================================ + +Intel 10 Gigabit Virtual Function Linux driver. +Copyright(c) 1999-2018 Intel Corporation. + +Contents +======== + +- Identifying Your Adapter +- Known Issues +- Support + +This driver supports 82599, X540, X550, and X552-based virtual function devices +that can only be activated on kernels that support SR-IOV. + +For questions related to hardware requirements, refer to the documentation +supplied with your Intel adapter. All hardware requirements listed apply to use +with Linux. + + +Identifying Your Adapter +======================== +The driver is compatible with devices based on the following: + + * Intel(R) Ethernet Controller 82598 + * Intel(R) Ethernet Controller 82599 + * Intel(R) Ethernet Controller X520 + * Intel(R) Ethernet Controller X540 + * Intel(R) Ethernet Controller x550 + * Intel(R) Ethernet Controller X552 + * Intel(R) Ethernet Controller X553 + +For information on how to identify your adapter, and for the latest Intel +network drivers, refer to the Intel Support website: +https://www.intel.com/support + +Known Issues/Troubleshooting +============================ + +SR-IOV requires the correct platform and OS support. + +The guest OS loading this driver must support MSI-X interrupts. + +This driver is only supported as a loadable module at this time. Intel is not +supplying patches against the kernel source to allow for static linking of the +drivers. + +VLANs: There is a limit of a total of 64 shared VLANs to 1 or more VFs. + + +Support +======= +For general information, go to the Intel support website at: +https://www.intel.com/support/ + +If an issue is identified with the released source code on a supported kernel +with a supported adapter, email the specific information related to the issue +to intel-wired-lan@lists.osuosl.org. diff --git a/Documentation/networking/device_drivers/ethernet/marvell/octeon_ep.rst b/Documentation/networking/device_drivers/ethernet/marvell/octeon_ep.rst new file mode 100644 index 0000000000..cad96c8d1f --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/marvell/octeon_ep.rst @@ -0,0 +1,36 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +==================================================================== +Linux kernel networking driver for Marvell's Octeon PCI Endpoint NIC +==================================================================== + +Network driver for Marvell's Octeon PCI EndPoint NIC. +Copyright (c) 2020 Marvell International Ltd. + +Contents +======== + +- `Overview`_ +- `Supported Devices`_ +- `Interface Control`_ + +Overview +======== +This driver implements networking functionality of Marvell's Octeon PCI +EndPoint NIC. + +Supported Devices +================= +Currently, this driver support following devices: + * Network controller: Cavium, Inc. Device b200 + * Network controller: Cavium, Inc. Device b400 + +Interface Control +================= +Network Interface control like changing mtu, link speed, link down/up are +done by writing command to mailbox command queue, a mailbox interface +implemented through a reserved region in BAR4. +This driver writes the commands into the mailbox and the firmware on the +Octeon device processes them. The firmware also sends unsolicited notifications +to driver for events suchs as link change, through notification queue +implemented as part of mailbox interface. diff --git a/Documentation/networking/device_drivers/ethernet/marvell/octeontx2.rst b/Documentation/networking/device_drivers/ethernet/marvell/octeontx2.rst new file mode 100644 index 0000000000..1e196cb9ce --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/marvell/octeontx2.rst @@ -0,0 +1,342 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) + +==================================== +Marvell OcteonTx2 RVU Kernel Drivers +==================================== + +Copyright (c) 2020 Marvell International Ltd. + +Contents +======== + +- `Overview`_ +- `Drivers`_ +- `Basic packet flow`_ +- `Devlink health reporters`_ +- `Quality of service`_ + +Overview +======== + +Resource virtualization unit (RVU) on Marvell's OcteonTX2 SOC maps HW +resources from the network, crypto and other functional blocks into +PCI-compatible physical and virtual functions. Each functional block +again has multiple local functions (LFs) for provisioning to PCI devices. +RVU supports multiple PCIe SRIOV physical functions (PFs) and virtual +functions (VFs). PF0 is called the administrative / admin function (AF) +and has privileges to provision RVU functional block's LFs to each of the +PF/VF. + +RVU managed networking functional blocks + - Network pool or buffer allocator (NPA) + - Network interface controller (NIX) + - Network parser CAM (NPC) + - Schedule/Synchronize/Order unit (SSO) + - Loopback interface (LBK) + +RVU managed non-networking functional blocks + - Crypto accelerator (CPT) + - Scheduled timers unit (TIM) + - Schedule/Synchronize/Order unit (SSO) + Used for both networking and non networking usecases + +Resource provisioning examples + - A PF/VF with NIX-LF & NPA-LF resources works as a pure network device + - A PF/VF with CPT-LF resource works as a pure crypto offload device. + +RVU functional blocks are highly configurable as per software requirements. + +Firmware setups following stuff before kernel boots + - Enables required number of RVU PFs based on number of physical links. + - Number of VFs per PF are either static or configurable at compile time. + Based on config, firmware assigns VFs to each of the PFs. + - Also assigns MSIX vectors to each of PF and VFs. + - These are not changed after kernel boot. + +Drivers +======= + +Linux kernel will have multiple drivers registering to different PF and VFs +of RVU. Wrt networking there will be 3 flavours of drivers. + +Admin Function driver +--------------------- + +As mentioned above RVU PF0 is called the admin function (AF), this driver +supports resource provisioning and configuration of functional blocks. +Doesn't handle any I/O. It sets up few basic stuff but most of the +funcionality is achieved via configuration requests from PFs and VFs. + +PF/VFs communicates with AF via a shared memory region (mailbox). Upon +receiving requests AF does resource provisioning and other HW configuration. +AF is always attached to host kernel, but PFs and their VFs may be used by host +kernel itself, or attached to VMs or to userspace applications like +DPDK etc. So AF has to handle provisioning/configuration requests sent +by any device from any domain. + +AF driver also interacts with underlying firmware to + - Manage physical ethernet links ie CGX LMACs. + - Retrieve information like speed, duplex, autoneg etc + - Retrieve PHY EEPROM and stats. + - Configure FEC, PAM modes + - etc + +From pure networking side AF driver supports following functionality. + - Map a physical link to a RVU PF to which a netdev is registered. + - Attach NIX and NPA block LFs to RVU PF/VF which provide buffer pools, RQs, SQs + for regular networking functionality. + - Flow control (pause frames) enable/disable/config. + - HW PTP timestamping related config. + - NPC parser profile config, basically how to parse pkt and what info to extract. + - NPC extract profile config, what to extract from the pkt to match data in MCAM entries. + - Manage NPC MCAM entries, upon request can frame and install requested packet forwarding rules. + - Defines receive side scaling (RSS) algorithms. + - Defines segmentation offload algorithms (eg TSO) + - VLAN stripping, capture and insertion config. + - SSO and TIM blocks config which provide packet scheduling support. + - Debugfs support, to check current resource provising, current status of + NPA pools, NIX RQ, SQ and CQs, various stats etc which helps in debugging issues. + - And many more. + +Physical Function driver +------------------------ + +This RVU PF handles IO, is mapped to a physical ethernet link and this +driver registers a netdev. This supports SR-IOV. As said above this driver +communicates with AF with a mailbox. To retrieve information from physical +links this driver talks to AF and AF gets that info from firmware and responds +back ie cannot talk to firmware directly. + +Supports ethtool for configuring links, RSS, queue count, queue size, +flow control, ntuple filters, dump PHY EEPROM, config FEC etc. + +Virtual Function driver +----------------------- + +There are two types VFs, VFs that share the physical link with their parent +SR-IOV PF and the VFs which work in pairs using internal HW loopback channels (LBK). + +Type1: + - These VFs and their parent PF share a physical link and used for outside communication. + - VFs cannot communicate with AF directly, they send mbox message to PF and PF + forwards that to AF. AF after processing, responds back to PF and PF forwards + the reply to VF. + - From functionality point of view there is no difference between PF and VF as same type + HW resources are attached to both. But user would be able to configure few stuff only + from PF as PF is treated as owner/admin of the link. + +Type2: + - RVU PF0 ie admin function creates these VFs and maps them to loopback block's channels. + - A set of two VFs (VF0 & VF1, VF2 & VF3 .. so on) works as a pair ie pkts sent out of + VF0 will be received by VF1 and vice versa. + - These VFs can be used by applications or virtual machines to communicate between them + without sending traffic outside. There is no switch present in HW, hence the support + for loopback VFs. + - These communicate directly with AF (PF0) via mbox. + +Except for the IO channels or links used for packet reception and transmission there is +no other difference between these VF types. AF driver takes care of IO channel mapping, +hence same VF driver works for both types of devices. + +Basic packet flow +================= + +Ingress +------- + +1. CGX LMAC receives packet. +2. Forwards the packet to the NIX block. +3. Then submitted to NPC block for parsing and then MCAM lookup to get the destination RVU device. +4. NIX LF attached to the destination RVU device allocates a buffer from RQ mapped buffer pool of NPA block LF. +5. RQ may be selected by RSS or by configuring MCAM rule with a RQ number. +6. Packet is DMA'ed and driver is notified. + +Egress +------ + +1. Driver prepares a send descriptor and submits to SQ for transmission. +2. The SQ is already configured (by AF) to transmit on a specific link/channel. +3. The SQ descriptor ring is maintained in buffers allocated from SQ mapped pool of NPA block LF. +4. NIX block transmits the pkt on the designated channel. +5. NPC MCAM entries can be installed to divert pkt onto a different channel. + +Devlink health reporters +======================== + +NPA Reporters +------------- +The NPA reporters are responsible for reporting and recovering the following group of errors: + +1. GENERAL events + + - Error due to operation of unmapped PF. + - Error due to disabled alloc/free for other HW blocks (NIX, SSO, TIM, DPI and AURA). + +2. ERROR events + + - Fault due to NPA_AQ_INST_S read or NPA_AQ_RES_S write. + - AQ Doorbell Error. + +3. RAS events + + - RAS Error Reporting for NPA_AQ_INST_S/NPA_AQ_RES_S. + +4. RVU events + + - Error due to unmapped slot. + +Sample Output:: + + ~# devlink health + pci/0002:01:00.0: + reporter hw_npa_intr + state healthy error 2872 recover 2872 last_dump_date 2020-12-10 last_dump_time 09:39:09 grace_period 0 auto_recover true auto_dump true + reporter hw_npa_gen + state healthy error 2872 recover 2872 last_dump_date 2020-12-11 last_dump_time 04:43:04 grace_period 0 auto_recover true auto_dump true + reporter hw_npa_err + state healthy error 2871 recover 2871 last_dump_date 2020-12-10 last_dump_time 09:39:17 grace_period 0 auto_recover true auto_dump true + reporter hw_npa_ras + state healthy error 0 recover 0 last_dump_date 2020-12-10 last_dump_time 09:32:40 grace_period 0 auto_recover true auto_dump true + +Each reporter dumps the + + - Error Type + - Error Register value + - Reason in words + +For example:: + + ~# devlink health dump show pci/0002:01:00.0 reporter hw_npa_gen + NPA_AF_GENERAL: + NPA General Interrupt Reg : 1 + NIX0: free disabled RX + ~# devlink health dump show pci/0002:01:00.0 reporter hw_npa_intr + NPA_AF_RVU: + NPA RVU Interrupt Reg : 1 + Unmap Slot Error + ~# devlink health dump show pci/0002:01:00.0 reporter hw_npa_err + NPA_AF_ERR: + NPA Error Interrupt Reg : 4096 + AQ Doorbell Error + + +NIX Reporters +------------- +The NIX reporters are responsible for reporting and recovering the following group of errors: + +1. GENERAL events + + - Receive mirror/multicast packet drop due to insufficient buffer. + - SMQ Flush operation. + +2. ERROR events + + - Memory Fault due to WQE read/write from multicast/mirror buffer. + - Receive multicast/mirror replication list error. + - Receive packet on an unmapped PF. + - Fault due to NIX_AQ_INST_S read or NIX_AQ_RES_S write. + - AQ Doorbell Error. + +3. RAS events + + - RAS Error Reporting for NIX Receive Multicast/Mirror Entry Structure. + - RAS Error Reporting for WQE/Packet Data read from Multicast/Mirror Buffer.. + - RAS Error Reporting for NIX_AQ_INST_S/NIX_AQ_RES_S. + +4. RVU events + + - Error due to unmapped slot. + +Sample Output:: + + ~# ./devlink health + pci/0002:01:00.0: + reporter hw_npa_intr + state healthy error 0 recover 0 grace_period 0 auto_recover true auto_dump true + reporter hw_npa_gen + state healthy error 0 recover 0 grace_period 0 auto_recover true auto_dump true + reporter hw_npa_err + state healthy error 0 recover 0 grace_period 0 auto_recover true auto_dump true + reporter hw_npa_ras + state healthy error 0 recover 0 grace_period 0 auto_recover true auto_dump true + reporter hw_nix_intr + state healthy error 1121 recover 1121 last_dump_date 2021-01-19 last_dump_time 05:42:26 grace_period 0 auto_recover true auto_dump true + reporter hw_nix_gen + state healthy error 949 recover 949 last_dump_date 2021-01-19 last_dump_time 05:42:43 grace_period 0 auto_recover true auto_dump true + reporter hw_nix_err + state healthy error 1147 recover 1147 last_dump_date 2021-01-19 last_dump_time 05:42:59 grace_period 0 auto_recover true auto_dump true + reporter hw_nix_ras + state healthy error 409 recover 409 last_dump_date 2021-01-19 last_dump_time 05:43:16 grace_period 0 auto_recover true auto_dump true + +Each reporter dumps the + + - Error Type + - Error Register value + - Reason in words + +For example:: + + ~# devlink health dump show pci/0002:01:00.0 reporter hw_nix_intr + NIX_AF_RVU: + NIX RVU Interrupt Reg : 1 + Unmap Slot Error + ~# devlink health dump show pci/0002:01:00.0 reporter hw_nix_gen + NIX_AF_GENERAL: + NIX General Interrupt Reg : 1 + Rx multicast pkt drop + ~# devlink health dump show pci/0002:01:00.0 reporter hw_nix_err + NIX_AF_ERR: + NIX Error Interrupt Reg : 64 + Rx on unmapped PF_FUNC + + +Quality of service +================== + + +Hardware algorithms used in scheduling +-------------------------------------- + +octeontx2 silicon and CN10K transmit interface consists of five transmit levels +starting from SMQ/MDQ, TL4 to TL1. Each packet will traverse MDQ, TL4 to TL1 +levels. Each level contains an array of queues to support scheduling and shaping. +The hardware uses the below algorithms depending on the priority of scheduler queues. +once the usercreates tc classes with different priorities, the driver configures +schedulers allocated to the class with specified priority along with rate-limiting +configuration. + +1. Strict Priority + + - Once packets are submitted to MDQ, hardware picks all active MDQs having different priority + using strict priority. + +2. Round Robin + + - Active MDQs having the same priority level are chosen using round robin. + + +Setup HTB offload +----------------- + +1. Enable HW TC offload on the interface:: + + # ethtool -K <interface> hw-tc-offload on + +2. Crate htb root:: + + # tc qdisc add dev <interface> clsact + # tc qdisc replace dev <interface> root handle 1: htb offload + +3. Create tc classes with different priorities:: + + # tc class add dev <interface> parent 1: classid 1:1 htb rate 10Gbit prio 1 + + # tc class add dev <interface> parent 1: classid 1:2 htb rate 10Gbit prio 7 + +4. Create tc classes with same priorities and different quantum:: + + # tc class add dev <interface> parent 1: classid 1:1 htb rate 10Gbit prio 2 quantum 409600 + + # tc class add dev <interface> parent 1: classid 1:2 htb rate 10Gbit prio 2 quantum 188416 + + # tc class add dev <interface> parent 1: classid 1:3 htb rate 10Gbit prio 2 quantum 32768 diff --git a/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/counters.rst b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/counters.rst new file mode 100644 index 0000000000..f69ee1ebee --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/counters.rst @@ -0,0 +1,1305 @@ +.. SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB +.. include:: <isonum.txt> + +================ +Ethtool counters +================ + +:Copyright: |copy| 2023, NVIDIA CORPORATION & AFFILIATES. All rights reserved. + +Contents +======== + +- `Overview`_ +- `Groups`_ +- `Types`_ +- `Descriptions`_ + +Overview +======== + +There are several counter groups based on where the counter is being counted. In +addition, each group of counters may have different counter types. + +These counter groups are based on which component in a networking setup, +illustrated below, that they describe:: + + ---------------------------------------- + | | + ---------------------------------------- ---------------------------------------- | + | Hypervisor | | VM | | + | | | | | + | ------------------- --------------- | | ------------------- --------------- | | + | | Ethernet driver | | RDMA driver | | | | Ethernet driver | | RDMA driver | | | + | ------------------- --------------- | | ------------------- --------------- | | + | | | | | | | | | + | ------------------- | | ------------------- | | + | | | | | |-- + ---------------------------------------- ---------------------------------------- + | | + ------------- ----------------------------- + | | + ------ ------ ------ ------ ------ ------ ------ + -----| PF |----------------------| VF |-| VF |-| VF |----- --| PF |--- --| PF |--- --| PF |--- + | ------ ------ ------ ------ | | ------ | | ------ | | ------ | + | | | | | | | | + | | | | | | | | + | | | | | | | | + | eSwitch | | eSwitch | | eSwitch | | eSwitch | + ---------------------------------------------------------- ----------- ----------- ----------- + ------------------------------------------------------------------------------- + | | + | | + | Uplink (no counters) | + ------------------------------------------------------------------------------- + --------------------------------------------------------------- + | | + | | + | MPFS (no counters) | + --------------------------------------------------------------- + | + | + | Port + +Groups +====== + +Ring + Software counters populated by the driver stack. + +Netdev + An aggregation of software ring counters. + +vPort counters + Traffic counters and drops due to steering or no buffers. May indicate issues + with NIC. These counters include Ethernet traffic counters (including Raw + Ethernet) and RDMA/RoCE traffic counters. + +Physical port counters + Counters that collect statistics about the PFs and VFs. May indicate issues + with NIC, link, or network. This measuring point holds information on + standardized counters like IEEE 802.3, RFC2863, RFC 2819, RFC 3635 and + additional counters like flow control, FEC and more. Physical port counters + are not exposed to virtual machines. + +Priority Port Counters + A set of the physical port counters, per priority per port. + +Types +===== + +Counters are divided into three types. + +Traffic Informative Counters + Counters which count traffic. These counters can be used for load estimation + or for general debug. + +Traffic Acceleration Counters + Counters which count traffic that was accelerated by Mellanox driver or by + hardware. The counters are an additional layer to the informative counter set, + and the same traffic is counted in both informative and acceleration counters. + +.. [#accel] Traffic acceleration counter. + +Error Counters + Increment of these counters might indicate a problem. Each of these counters + has an explanation and correction action. + +Statistic can be fetched via the `ip link` or `ethtool` commands. `ethtool` +provides more detailed information.:: + + ip –s link show <if-name> + ethtool -S <if-name> + +Descriptions +============ + +XSK, PTP, and QoS counters that are similar to counters defined previously will +not be separately listed. For example, `ptp_tx[i]_packets` will not be +explicitly documented since `tx[i]_packets` describes the behavior of both +counters, except `ptp_tx[i]_packets` is only counted when precision time +protocol is used. + +Ring / Netdev Counter +---------------------------- +The following counters are available per ring or software port. + +These counters provide information on the amount of traffic that was accelerated +by the NIC. The counters are counting the accelerated traffic in addition to the +standard counters which counts it (i.e. accelerated traffic is counted twice). + +The counter names in the table below refers to both ring and port counters. The +notation for ring counters includes the [i] index without the braces. The +notation for port counters doesn't include the [i]. A counter name +`rx[i]_packets` will be printed as `rx0_packets` for ring 0 and `rx_packets` for +the software port. + +.. flat-table:: Ring / Software Port Counter Table + :widths: 2 3 1 + + * - Counter + - Description + - Type + + * - `rx[i]_packets` + - The number of packets received on ring i. + - Informative + + * - `rx[i]_bytes` + - The number of bytes received on ring i. + - Informative + + * - `tx[i]_packets` + - The number of packets transmitted on ring i. + - Informative + + * - `tx[i]_bytes` + - The number of bytes transmitted on ring i. + - Informative + + * - `tx[i]_recover` + - The number of times the SQ was recovered. + - Error + + * - `tx[i]_cqes` + - Number of CQEs events on SQ issued on ring i. + - Informative + + * - `tx[i]_cqe_err` + - The number of error CQEs encountered on the SQ for ring i. + - Error + + * - `tx[i]_tso_packets` + - The number of TSO packets transmitted on ring i [#accel]_. + - Acceleration + + * - `tx[i]_tso_bytes` + - The number of TSO bytes transmitted on ring i [#accel]_. + - Acceleration + + * - `tx[i]_tso_inner_packets` + - The number of TSO packets which are indicated to be carry internal + encapsulation transmitted on ring i [#accel]_. + - Acceleration + + * - `tx[i]_tso_inner_bytes` + - The number of TSO bytes which are indicated to be carry internal + encapsulation transmitted on ring i [#accel]_. + - Acceleration + + * - `rx[i]_gro_packets` + - Number of received packets processed using hardware-accelerated GRO. The + number of hardware GRO offloaded packets received on ring i. + - Acceleration + + * - `rx[i]_gro_bytes` + - Number of received bytes processed using hardware-accelerated GRO. The + number of hardware GRO offloaded bytes received on ring i. + - Acceleration + + * - `rx[i]_gro_skbs` + - The number of receive SKBs constructed while performing + hardware-accelerated GRO. + - Informative + + * - `rx[i]_gro_match_packets` + - Number of received packets processed using hardware-accelerated GRO that + met the flow table match criteria. + - Informative + + * - `rx[i]_gro_large_hds` + - Number of receive packets using hardware-accelerated GRO that have large + headers that require additional memory to be allocated. + - Informative + + * - `rx[i]_lro_packets` + - The number of LRO packets received on ring i [#accel]_. + - Acceleration + + * - `rx[i]_lro_bytes` + - The number of LRO bytes received on ring i [#accel]_. + - Acceleration + + * - `rx[i]_ecn_mark` + - The number of received packets where the ECN mark was turned on. + - Informative + + * - `rx_oversize_pkts_buffer` + - The number of dropped received packets due to length which arrived to RQ + and exceed software buffer size allocated by the device for incoming + traffic. It might imply that the device MTU is larger than the software + buffers size. + - Error + + * - `rx_oversize_pkts_sw_drop` + - Number of received packets dropped in software because the CQE data is + larger than the MTU size. + - Error + + * - `rx[i]_csum_unnecessary` + - Packets received with a `CHECKSUM_UNNECESSARY` on ring i [#accel]_. + - Acceleration + + * - `rx[i]_csum_unnecessary_inner` + - Packets received with inner encapsulation with a `CHECKSUM_UNNECESSARY` + on ring i [#accel]_. + - Acceleration + + * - `rx[i]_csum_none` + - Packets received with a `CHECKSUM_NONE` on ring i [#accel]_. + - Acceleration + + * - `rx[i]_csum_complete` + - Packets received with a `CHECKSUM_COMPLETE` on ring i [#accel]_. + - Acceleration + + * - `rx[i]_csum_complete_tail` + - Number of received packets that had checksum calculation computed, + potentially needed padding, and were able to do so with + `CHECKSUM_PARTIAL`. + - Informative + + * - `rx[i]_csum_complete_tail_slow` + - Number of received packets that need padding larger than eight bytes for + the checksum. + - Informative + + * - `tx[i]_csum_partial` + - Packets transmitted with a `CHECKSUM_PARTIAL` on ring i [#accel]_. + - Acceleration + + * - `tx[i]_csum_partial_inner` + - Packets transmitted with inner encapsulation with a `CHECKSUM_PARTIAL` on + ring i [#accel]_. + - Acceleration + + * - `tx[i]_csum_none` + - Packets transmitted with no hardware checksum acceleration on ring i. + - Informative + + * - `tx[i]_stopped` / `tx_queue_stopped` [#ring_global]_ + - Events where SQ was full on ring i. If this counter is increased, check + the amount of buffers allocated for transmission. + - Informative + + * - `tx[i]_wake` / `tx_queue_wake` [#ring_global]_ + - Events where SQ was full and has become not full on ring i. + - Informative + + * - `tx[i]_dropped` / `tx_queue_dropped` [#ring_global]_ + - Packets transmitted that were dropped due to DMA mapping failure on + ring i. If this counter is increased, check the amount of buffers + allocated for transmission. + - Error + + * - `tx[i]_nop` + - The number of nop WQEs (empty WQEs) inserted to the SQ (related to + ring i) due to the reach of the end of the cyclic buffer. When reaching + near to the end of cyclic buffer the driver may add those empty WQEs to + avoid handling a state the a WQE start in the end of the queue and ends + in the beginning of the queue. This is a normal condition. + - Informative + + * - `tx[i]_added_vlan_packets` + - The number of packets sent where vlan tag insertion was offloaded to the + hardware. + - Acceleration + + * - `rx[i]_removed_vlan_packets` + - The number of packets received where vlan tag stripping was offloaded to + the hardware. + - Acceleration + + * - `rx[i]_wqe_err` + - The number of wrong opcodes received on ring i. + - Error + + * - `rx[i]_mpwqe_frag` + - The number of WQEs that failed to allocate compound page and hence + fragmented MPWQE’s (Multi Packet WQEs) were used on ring i. If this + counter raise, it may suggest that there is no enough memory for large + pages, the driver allocated fragmented pages. This is not abnormal + condition. + - Informative + + * - `rx[i]_mpwqe_filler_cqes` + - The number of filler CQEs events that were issued on ring i. + - Informative + + * - `rx[i]_mpwqe_filler_strides` + - The number of strides consumed by filler CQEs on ring i. + - Informative + + * - `tx[i]_mpwqe_blks` + - The number of send blocks processed from Multi-Packet WQEs (mpwqe). + - Informative + + * - `tx[i]_mpwqe_pkts` + - The number of send packets processed from Multi-Packet WQEs (mpwqe). + - Informative + + * - `rx[i]_cqe_compress_blks` + - The number of receive blocks with CQE compression on ring i [#accel]_. + - Acceleration + + * - `rx[i]_cqe_compress_pkts` + - The number of receive packets with CQE compression on ring i [#accel]_. + - Acceleration + + * - `rx[i]_arfs_add` + - The number of aRFS flow rules added to the device for direct RQ steering + on ring i [#accel]_. + - Acceleration + + * - `rx[i]_arfs_request_in` + - Number of flow rules that have been requested to move into ring i for + direct RQ steering [#accel]_. + - Acceleration + + * - `rx[i]_arfs_request_out` + - Number of flow rules that have been requested to move out of ring i [#accel]_. + - Acceleration + + * - `rx[i]_arfs_expired` + - Number of flow rules that have been expired and removed [#accel]_. + - Acceleration + + * - `rx[i]_arfs_err` + - Number of flow rules that failed to be added to the flow table. + - Error + + * - `rx[i]_recover` + - The number of times the RQ was recovered. + - Error + + * - `tx[i]_xmit_more` + - The number of packets sent with `xmit_more` indication set on the skbuff + (no doorbell). + - Acceleration + + * - `ch[i]_poll` + - The number of invocations of NAPI poll of channel i. + - Informative + + * - `ch[i]_arm` + - The number of times the NAPI poll function completed and armed the + completion queues on channel i. + - Informative + + * - `ch[i]_aff_change` + - The number of times the NAPI poll function explicitly stopped execution + on a CPU due to a change in affinity, on channel i. + - Informative + + * - `ch[i]_events` + - The number of hard interrupt events on the completion queues of channel i. + - Informative + + * - `ch[i]_eq_rearm` + - The number of times the EQ was recovered. + - Error + + * - `ch[i]_force_irq` + - Number of times NAPI is triggered by XSK wakeups by posting a NOP to + ICOSQ. + - Acceleration + + * - `rx[i]_congst_umr` + - The number of times an outstanding UMR request is delayed due to + congestion, on ring i. + - Informative + + * - `rx_pp_alloc_fast` + - Number of successful fast path allocations. + - Informative + + * - `rx_pp_alloc_slow` + - Number of slow path order-0 allocations. + - Informative + + * - `rx_pp_alloc_slow_high_order` + - Number of slow path high order allocations. + - Informative + + * - `rx_pp_alloc_empty` + - Counter is incremented when ptr ring is empty, so a slow path allocation + was forced. + - Informative + + * - `rx_pp_alloc_refill` + - Counter is incremented when an allocation which triggered a refill of the + cache. + - Informative + + * - `rx_pp_alloc_waive` + - Counter is incremented when pages obtained from the ptr ring that cannot + be added to the cache due to a NUMA mismatch. + - Informative + + * - `rx_pp_recycle_cached` + - Counter is incremented when recycling placed page in the page pool cache. + - Informative + + * - `rx_pp_recycle_cache_full` + - Counter is incremented when page pool cache was full. + - Informative + + * - `rx_pp_recycle_ring` + - Counter is incremented when page placed into the ptr ring. + - Informative + + * - `rx_pp_recycle_ring_full` + - Counter is incremented when page released from page pool because the ptr + ring was full. + - Informative + + * - `rx_pp_recycle_released_ref` + - Counter is incremented when page released (and not recycled) because + refcnt > 1. + - Informative + + * - `rx[i]_xsk_buff_alloc_err` + - The number of times allocating an skb or XSK buffer failed in the XSK RQ + context. + - Error + + * - `rx[i]_xdp_tx_xmit` + - The number of packets forwarded back to the port due to XDP program + `XDP_TX` action (bouncing). these packets are not counted by other + software counters. These packets are counted by physical port and vPort + counters. + - Informative + + * - `rx[i]_xdp_tx_mpwqe` + - Number of multi-packet WQEs transmitted by the netdev and `XDP_TX`-ed by + the netdev during the RQ context. + - Acceleration + + * - `rx[i]_xdp_tx_inlnw` + - Number of WQE data segments transmitted where the data could be inlined + in the WQE and then `XDP_TX`-ed during the RQ context. + - Acceleration + + * - `rx[i]_xdp_tx_nops` + - Number of NOP WQEBBs (WQE building blocks) received posted to the XDP SQ. + - Acceleration + + * - `rx[i]_xdp_tx_full` + - The number of packets that should have been forwarded back to the port + due to `XDP_TX` action but were dropped due to full tx queue. These packets + are not counted by other software counters. These packets are counted by + physical port and vPort counters. You may open more rx queues and spread + traffic rx over all queues and/or increase rx ring size. + - Error + + * - `rx[i]_xdp_tx_err` + - The number of times an `XDP_TX` error such as frame too long and frame + too short occurred on `XDP_TX` ring of RX ring. + - Error + + * - `rx[i]_xdp_tx_cqes` / `rx_xdp_tx_cqe` [#ring_global]_ + - The number of completions received on the CQ of the `XDP_TX` ring. + - Informative + + * - `rx[i]_xdp_drop` + - The number of packets dropped due to XDP program `XDP_DROP` action. these + packets are not counted by other software counters. These packets are + counted by physical port and vPort counters. + - Informative + + * - `rx[i]_xdp_redirect` + - The number of times an XDP redirect action was triggered on ring i. + - Acceleration + + * - `tx[i]_xdp_xmit` + - The number of packets redirected to the interface(due to XDP redirect). + These packets are not counted by other software counters. These packets + are counted by physical port and vPort counters. + - Informative + + * - `tx[i]_xdp_full` + - The number of packets redirected to the interface(due to XDP redirect), + but were dropped due to full tx queue. these packets are not counted by + other software counters. you may enlarge tx queues. + - Informative + + * - `tx[i]_xdp_mpwqe` + - Number of multi-packet WQEs offloaded onto the NIC that were + `XDP_REDIRECT`-ed from other netdevs. + - Acceleration + + * - `tx[i]_xdp_inlnw` + - Number of WQE data segments where the data could be inlined in the WQE + where the data segments were `XDP_REDIRECT`-ed from other netdevs. + - Acceleration + + * - `tx[i]_xdp_nops` + - Number of NOP WQEBBs (WQE building blocks) posted to the SQ that were + `XDP_REDIRECT`-ed from other netdevs. + - Acceleration + + * - `tx[i]_xdp_err` + - The number of packets redirected to the interface(due to XDP redirect) + but were dropped due to error such as frame too long and frame too short. + - Error + + * - `tx[i]_xdp_cqes` + - The number of completions received for packets redirected to the + interface(due to XDP redirect) on the CQ. + - Informative + + * - `tx[i]_xsk_xmit` + - The number of packets transmitted using XSK zerocopy functionality. + - Acceleration + + * - `tx[i]_xsk_mpwqe` + - Number of multi-packet WQEs offloaded onto the NIC that were + `XDP_REDIRECT`-ed from other netdevs. + - Acceleration + + * - `tx[i]_xsk_inlnw` + - Number of WQE data segments where the data could be inlined in the WQE + that are transmitted using XSK zerocopy. + - Acceleration + + * - `tx[i]_xsk_full` + - Number of times doorbell is rung in XSK zerocopy mode when SQ is full. + - Error + + * - `tx[i]_xsk_err` + - Number of errors that occurred in XSK zerocopy mode such as if the data + size is larger than the MTU size. + - Error + + * - `tx[i]_xsk_cqes` + - Number of CQEs processed in XSK zerocopy mode. + - Acceleration + + * - `tx_tls_ctx` + - Number of TLS TX HW offload contexts added to device for encryption. + - Acceleration + + * - `tx_tls_del` + - Number of TLS TX HW offload contexts removed from device (connection + closed). + - Acceleration + + * - `tx_tls_pool_alloc` + - Number of times a unit of work is successfully allocated in the TLS HW + offload pool. + - Acceleration + + * - `tx_tls_pool_free` + - Number of times a unit of work is freed in the TLS HW offload pool. + - Acceleration + + * - `rx_tls_ctx` + - Number of TLS RX HW offload contexts added to device for decryption. + - Acceleration + + * - `rx_tls_del` + - Number of TLS RX HW offload contexts deleted from device (connection has + finished). + - Acceleration + + * - `rx[i]_tls_decrypted_packets` + - Number of successfully decrypted RX packets which were part of a TLS + stream. + - Acceleration + + * - `rx[i]_tls_decrypted_bytes` + - Number of TLS payload bytes in RX packets which were successfully + decrypted. + - Acceleration + + * - `rx[i]_tls_resync_req_pkt` + - Number of received TLS packets with a resync request. + - Acceleration + + * - `rx[i]_tls_resync_req_start` + - Number of times the TLS async resync request was started. + - Acceleration + + * - `rx[i]_tls_resync_req_end` + - Number of times the TLS async resync request properly ended with + providing the HW tracked tcp-seq. + - Acceleration + + * - `rx[i]_tls_resync_req_skip` + - Number of times the TLS async resync request procedure was started but + not properly ended. + - Error + + * - `rx[i]_tls_resync_res_ok` + - Number of times the TLS resync response call to the driver was + successfully handled. + - Acceleration + + * - `rx[i]_tls_resync_res_retry` + - Number of times the TLS resync response call to the driver was + reattempted when ICOSQ is full. + - Error + + * - `rx[i]_tls_resync_res_skip` + - Number of times the TLS resync response call to the driver was terminated + unsuccessfully. + - Error + + * - `rx[i]_tls_err` + - Number of times when CQE TLS offload was problematic. + - Error + + * - `tx[i]_tls_encrypted_packets` + - The number of send packets that are TLS encrypted by the kernel. + - Acceleration + + * - `tx[i]_tls_encrypted_bytes` + - The number of send bytes that are TLS encrypted by the kernel. + - Acceleration + + * - `tx[i]_tls_ooo` + - Number of times out of order TLS SQE fragments were handled on ring i. + - Acceleration + + * - `tx[i]_tls_dump_packets` + - Number of TLS decrypted packets copied over from NIC over DMA. + - Acceleration + + * - `tx[i]_tls_dump_bytes` + - Number of TLS decrypted bytes copied over from NIC over DMA. + - Acceleration + + * - `tx[i]_tls_resync_bytes` + - Number of TLS bytes requested to be resynchronized in order to be + decrypted. + - Acceleration + + * - `tx[i]_tls_skip_no_sync_data` + - Number of TLS send data that can safely be skipped / do not need to be + decrypted. + - Acceleration + + * - `tx[i]_tls_drop_no_sync_data` + - Number of TLS send data that were dropped due to retransmission of TLS + data. + - Acceleration + + * - `ptp_cq[i]_abort` + - Number of times a CQE has to be skipped in precision time protocol due to + a skew between the port timestamp and CQE timestamp being greater than + 128 seconds. + - Error + + * - `ptp_cq[i]_abort_abs_diff_ns` + - Accumulation of time differences between the port timestamp and CQE + timestamp when the difference is greater than 128 seconds in precision + time protocol. + - Error + + * - `ptp_cq[i]_late_cqe` + - Number of times a CQE has been delivered on the PTP timestamping CQ when + the CQE was not expected since a certain amount of time had elapsed where + the device typically ensures not posting the CQE. + - Error + +.. [#ring_global] The corresponding ring and global counters do not share the + same name (i.e. do not follow the common naming scheme). + +vPort Counters +-------------- +Counters on the NIC port that is connected to a eSwitch. + +.. flat-table:: vPort Counter Table + :widths: 2 3 1 + + * - Counter + - Description + - Type + + * - `rx_vport_unicast_packets` + - Unicast packets received, steered to a port including Raw Ethernet + QP/DPDK traffic, excluding RDMA traffic. + - Informative + + * - `rx_vport_unicast_bytes` + - Unicast bytes received, steered to a port including Raw Ethernet QP/DPDK + traffic, excluding RDMA traffic. + - Informative + + * - `tx_vport_unicast_packets` + - Unicast packets transmitted, steered from a port including Raw Ethernet + QP/DPDK traffic, excluding RDMA traffic. + - Informative + + * - `tx_vport_unicast_bytes` + - Unicast bytes transmitted, steered from a port including Raw Ethernet + QP/DPDK traffic, excluding RDMA traffic. + - Informative + + * - `rx_vport_multicast_packets` + - Multicast packets received, steered to a port including Raw Ethernet + QP/DPDK traffic, excluding RDMA traffic. + - Informative + + * - `rx_vport_multicast_bytes` + - Multicast bytes received, steered to a port including Raw Ethernet + QP/DPDK traffic, excluding RDMA traffic. + - Informative + + * - `tx_vport_multicast_packets` + - Multicast packets transmitted, steered from a port including Raw Ethernet + QP/DPDK traffic, excluding RDMA traffic. + - Informative + + * - `tx_vport_multicast_bytes` + - Multicast bytes transmitted, steered from a port including Raw Ethernet + QP/DPDK traffic, excluding RDMA traffic. + - Informative + + * - `rx_vport_broadcast_packets` + - Broadcast packets received, steered to a port including Raw Ethernet + QP/DPDK traffic, excluding RDMA traffic. + - Informative + + * - `rx_vport_broadcast_bytes` + - Broadcast bytes received, steered to a port including Raw Ethernet + QP/DPDK traffic, excluding RDMA traffic. + - Informative + + * - `tx_vport_broadcast_packets` + - Broadcast packets transmitted, steered from a port including Raw Ethernet + QP/DPDK traffic, excluding RDMA traffic. + - Informative + + * - `tx_vport_broadcast_bytes` + - Broadcast bytes transmitted, steered from a port including Raw Ethernet + QP/DPDK traffic, excluding RDMA traffic. + - Informative + + * - `rx_vport_rdma_unicast_packets` + - RDMA unicast packets received, steered to a port (counters counts + RoCE/UD/RC traffic) [#accel]_. + - Acceleration + + * - `rx_vport_rdma_unicast_bytes` + - RDMA unicast bytes received, steered to a port (counters counts + RoCE/UD/RC traffic) [#accel]_. + - Acceleration + + * - `tx_vport_rdma_unicast_packets` + - RDMA unicast packets transmitted, steered from a port (counters counts + RoCE/UD/RC traffic) [#accel]_. + - Acceleration + + * - `tx_vport_rdma_unicast_bytes` + - RDMA unicast bytes transmitted, steered from a port (counters counts + RoCE/UD/RC traffic) [#accel]_. + - Acceleration + + * - `rx_vport_rdma_multicast_packets` + - RDMA multicast packets received, steered to a port (counters counts + RoCE/UD/RC traffic) [#accel]_. + - Acceleration + + * - `rx_vport_rdma_multicast_bytes` + - RDMA multicast bytes received, steered to a port (counters counts + RoCE/UD/RC traffic) [#accel]_. + - Acceleration + + * - `tx_vport_rdma_multicast_packets` + - RDMA multicast packets transmitted, steered from a port (counters counts + RoCE/UD/RC traffic) [#accel]_. + - Acceleration + + * - `tx_vport_rdma_multicast_bytes` + - RDMA multicast bytes transmitted, steered from a port (counters counts + RoCE/UD/RC traffic) [#accel]_. + - Acceleration + + * - `vport_loopback_packets` + - Unicast, multicast and broadcast packets that were loop-back (received + and transmitted), IB/Eth [#accel]_. + - Acceleration + + * - `vport_loopback_bytes` + - Unicast, multicast and broadcast bytes that were loop-back (received + and transmitted), IB/Eth [#accel]_. + - Acceleration + + * - `rx_steer_missed_packets` + - Number of packets that was received by the NIC, however was discarded + because it did not match any flow in the NIC flow table. + - Error + + * - `rx_packets` + - Representor only: packets received, that were handled by the hypervisor. + - Informative + + * - `rx_bytes` + - Representor only: bytes received, that were handled by the hypervisor. + - Informative + + * - `tx_packets` + - Representor only: packets transmitted, that were handled by the + hypervisor. + - Informative + + * - `tx_bytes` + - Representor only: bytes transmitted, that were handled by the hypervisor. + - Informative + + * - `dev_internal_queue_oob` + - The number of dropped packets due to lack of receive WQEs for an internal + device RQ. + - Error + +Physical Port Counters +---------------------- +The physical port counters are the counters on the external port connecting the +adapter to the network. This measuring point holds information on standardized +counters like IEEE 802.3, RFC2863, RFC 2819, RFC 3635 and additional counters +like flow control, FEC and more. + +.. flat-table:: Physical Port Counter Table + :widths: 2 3 1 + + * - Counter + - Description + - Type + + * - `rx_packets_phy` + - The number of packets received on the physical port. This counter doesn’t + include packets that were discarded due to FCS, frame size and similar + errors. + - Informative + + * - `tx_packets_phy` + - The number of packets transmitted on the physical port. + - Informative + + * - `rx_bytes_phy` + - The number of bytes received on the physical port, including Ethernet + header and FCS. + - Informative + + * - `tx_bytes_phy` + - The number of bytes transmitted on the physical port. + - Informative + + * - `rx_multicast_phy` + - The number of multicast packets received on the physical port. + - Informative + + * - `tx_multicast_phy` + - The number of multicast packets transmitted on the physical port. + - Informative + + * - `rx_broadcast_phy` + - The number of broadcast packets received on the physical port. + - Informative + + * - `tx_broadcast_phy` + - The number of broadcast packets transmitted on the physical port. + - Informative + + * - `rx_crc_errors_phy` + - The number of dropped received packets due to FCS (Frame Check Sequence) + error on the physical port. If this counter is increased in high rate, + check the link quality using `rx_symbol_error_phy` and + `rx_corrected_bits_phy` counters below. + - Error + + * - `rx_in_range_len_errors_phy` + - The number of received packets dropped due to length/type errors on a + physical port. + - Error + + * - `rx_out_of_range_len_phy` + - The number of received packets dropped due to length greater than allowed + on a physical port. If this counter is increasing, it implies that the + peer connected to the adapter has a larger MTU configured. Using same MTU + configuration shall resolve this issue. + - Error + + * - `rx_oversize_pkts_phy` + - The number of dropped received packets due to length which exceed MTU + size on a physical port. If this counter is increasing, it implies that + the peer connected to the adapter has a larger MTU configured. Using same + MTU configuration shall resolve this issue. + - Error + + * - `rx_symbol_err_phy` + - The number of received packets dropped due to physical coding errors + (symbol errors) on a physical port. + - Error + + * - `rx_mac_control_phy` + - The number of MAC control packets received on the physical port. + - Informative + + * - `tx_mac_control_phy` + - The number of MAC control packets transmitted on the physical port. + - Informative + + * - `rx_pause_ctrl_phy` + - The number of link layer pause packets received on a physical port. If + this counter is increasing, it implies that the network is congested and + cannot absorb the traffic coming from to the adapter. + - Informative + + * - `tx_pause_ctrl_phy` + - The number of link layer pause packets transmitted on a physical port. If + this counter is increasing, it implies that the NIC is congested and + cannot absorb the traffic coming from the network. + - Informative + + * - `rx_unsupported_op_phy` + - The number of MAC control packets received with unsupported opcode on a + physical port. + - Error + + * - `rx_discards_phy` + - The number of received packets dropped due to lack of buffers on a + physical port. If this counter is increasing, it implies that the adapter + is congested and cannot absorb the traffic coming from the network. + - Error + + * - `tx_discards_phy` + - The number of packets which were discarded on transmission, even no + errors were detected. the drop might occur due to link in down state, + head of line drop, pause from the network, etc. + - Error + + * - `tx_errors_phy` + - The number of transmitted packets dropped due to a length which exceed + MTU size on a physical port. + - Error + + * - `rx_undersize_pkts_phy` + - The number of received packets dropped due to length which is shorter + than 64 bytes on a physical port. If this counter is increasing, it + implies that the peer connected to the adapter has a non-standard MTU + configured or malformed packet had arrived. + - Error + + * - `rx_fragments_phy` + - The number of received packets dropped due to a length which is shorter + than 64 bytes and has FCS error on a physical port. If this counter is + increasing, it implies that the peer connected to the adapter has a + non-standard MTU configured. + - Error + + * - `rx_jabbers_phy` + - The number of received packets d due to a length which is longer than 64 + bytes and had FCS error on a physical port. + - Error + + * - `rx_64_bytes_phy` + - The number of packets received on the physical port with size of 64 bytes. + - Informative + + * - `rx_65_to_127_bytes_phy` + - The number of packets received on the physical port with size of 65 to + 127 bytes. + - Informative + + * - `rx_128_to_255_bytes_phy` + - The number of packets received on the physical port with size of 128 to + 255 bytes. + - Informative + + * - `rx_256_to_511_bytes_phy` + - The number of packets received on the physical port with size of 256 to + 512 bytes. + - Informative + + * - `rx_512_to_1023_bytes_phy` + - The number of packets received on the physical port with size of 512 to + 1023 bytes. + - Informative + + * - `rx_1024_to_1518_bytes_phy` + - The number of packets received on the physical port with size of 1024 to + 1518 bytes. + - Informative + + * - `rx_1519_to_2047_bytes_phy` + - The number of packets received on the physical port with size of 1519 to + 2047 bytes. + - Informative + + * - `rx_2048_to_4095_bytes_phy` + - The number of packets received on the physical port with size of 2048 to + 4095 bytes. + - Informative + + * - `rx_4096_to_8191_bytes_phy` + - The number of packets received on the physical port with size of 4096 to + 8191 bytes. + - Informative + + * - `rx_8192_to_10239_bytes_phy` + - The number of packets received on the physical port with size of 8192 to + 10239 bytes. + - Informative + + * - `link_down_events_phy` + - The number of times where the link operative state changed to down. In + case this counter is increasing it may imply on port flapping. You may + need to replace the cable/transceiver. + - Error + + * - `rx_out_of_buffer` + - Number of times receive queue had no software buffers allocated for the + adapter's incoming traffic. + - Error + + * - `module_bus_stuck` + - The number of times that module's I\ :sup:`2`\C bus (data or clock) + short-wire was detected. You may need to replace the cable/transceiver. + - Error + + * - `module_high_temp` + - The number of times that the module temperature was too high. If this + issue persist, you may need to check the ambient temperature or replace + the cable/transceiver module. + - Error + + * - `module_bad_shorted` + - The number of times that the module cables were shorted. You may need to + replace the cable/transceiver module. + - Error + + * - `module_unplug` + - The number of times that module was ejected. + - Informative + + * - `rx_buffer_passed_thres_phy` + - The number of events where the port receive buffer was over 85% full. + - Informative + + * - `tx_pause_storm_warning_events` + - The number of times the device was sending pauses for a long period of + time. + - Informative + + * - `tx_pause_storm_error_events` + - The number of times the device was sending pauses for a long period of + time, reaching time out and disabling transmission of pause frames. on + the period where pause frames were disabled, drop could have been + occurred. + - Error + + * - `rx[i]_buff_alloc_err` + - Failed to allocate a buffer to received packet (or SKB) on ring i. + - Error + + * - `rx_bits_phy` + - This counter provides information on the total amount of traffic that + could have been received and can be used as a guideline to measure the + ratio of errored traffic in `rx_pcs_symbol_err_phy` and + `rx_corrected_bits_phy`. + - Informative + + * - `rx_pcs_symbol_err_phy` + - This counter counts the number of symbol errors that wasn’t corrected by + FEC correction algorithm or that FEC algorithm was not active on this + interface. If this counter is increasing, it implies that the link + between the NIC and the network is suffering from high BER, and that + traffic is lost. You may need to replace the cable/transceiver. The error + rate is the number of `rx_pcs_symbol_err_phy` divided by the number of + `rx_bits_phy` on a specific time frame. + - Error + + * - `rx_corrected_bits_phy` + - The number of corrected bits on this port according to active FEC + (RS/FC). If this counter is increasing, it implies that the link between + the NIC and the network is suffering from high BER. The corrected bit + rate is the number of `rx_corrected_bits_phy` divided by the number of + `rx_bits_phy` on a specific time frame. + - Error + + * - `rx_err_lane_[l]_phy` + - This counter counts the number of physical raw errors per lane l index. + The counter counts errors before FEC corrections. If this counter is + increasing, it implies that the link between the NIC and the network is + suffering from high BER, and that traffic might be lost. You may need to + replace the cable/transceiver. Please check in accordance with + `rx_corrected_bits_phy`. + - Error + + * - `rx_global_pause` + - The number of pause packets received on the physical port. If this + counter is increasing, it implies that the network is congested and + cannot absorb the traffic coming from the adapter. Note: This counter is + only enabled when global pause mode is enabled. + - Informative + + * - `rx_global_pause_duration` + - The duration of pause received (in microSec) on the physical port. The + counter represents the time the port did not send any traffic. If this + counter is increasing, it implies that the network is congested and + cannot absorb the traffic coming from the adapter. Note: This counter is + only enabled when global pause mode is enabled. + - Informative + + * - `tx_global_pause` + - The number of pause packets transmitted on a physical port. If this + counter is increasing, it implies that the adapter is congested and + cannot absorb the traffic coming from the network. Note: This counter is + only enabled when global pause mode is enabled. + - Informative + + * - `tx_global_pause_duration` + - The duration of pause transmitter (in microSec) on the physical port. + Note: This counter is only enabled when global pause mode is enabled. + - Informative + + * - `rx_global_pause_transition` + - The number of times a transition from Xoff to Xon on the physical port + has occurred. Note: This counter is only enabled when global pause mode + is enabled. + - Informative + + * - `rx_if_down_packets` + - The number of received packets that were dropped due to interface down. + - Informative + +Priority Port Counters +---------------------- +The following counters are physical port counters that are counted per L2 +priority (0-7). + +**Note:** `p` in the counter name represents the priority. + +.. flat-table:: Priority Port Counter Table + :widths: 2 3 1 + + * - Counter + - Description + - Type + + * - `rx_prio[p]_bytes` + - The number of bytes received with priority p on the physical port. + - Informative + + * - `rx_prio[p]_packets` + - The number of packets received with priority p on the physical port. + - Informative + + * - `tx_prio[p]_bytes` + - The number of bytes transmitted on priority p on the physical port. + - Informative + + * - `tx_prio[p]_packets` + - The number of packets transmitted on priority p on the physical port. + - Informative + + * - `rx_prio[p]_pause` + - The number of pause packets received with priority p on a physical port. + If this counter is increasing, it implies that the network is congested + and cannot absorb the traffic coming from the adapter. Note: This counter + is available only if PFC was enabled on priority p. + - Informative + + * - `rx_prio[p]_pause_duration` + - The duration of pause received (in microSec) on priority p on the + physical port. The counter represents the time the port did not send any + traffic on this priority. If this counter is increasing, it implies that + the network is congested and cannot absorb the traffic coming from the + adapter. Note: This counter is available only if PFC was enabled on + priority p. + - Informative + + * - `rx_prio[p]_pause_transition` + - The number of times a transition from Xoff to Xon on priority p on the + physical port has occurred. Note: This counter is available only if PFC + was enabled on priority p. + - Informative + + * - `tx_prio[p]_pause` + - The number of pause packets transmitted on priority p on a physical port. + If this counter is increasing, it implies that the adapter is congested + and cannot absorb the traffic coming from the network. Note: This counter + is available only if PFC was enabled on priority p. + - Informative + + * - `tx_prio[p]_pause_duration` + - The duration of pause transmitter (in microSec) on priority p on the + physical port. Note: This counter is available only if PFC was enabled on + priority p. + - Informative + + * - `rx_prio[p]_buf_discard` + - The number of packets discarded by device due to lack of per host receive + buffers. + - Informative + + * - `rx_prio[p]_cong_discard` + - The number of packets discarded by device due to per host congestion. + - Informative + + * - `rx_prio[p]_marked` + - The number of packets ecn marked by device due to per host congestion. + - Informative + + * - `rx_prio[p]_discards` + - The number of packets discarded by device due to lack of receive buffers. + - Informative + +Device Counters +--------------- +.. flat-table:: Device Counter Table + :widths: 2 3 1 + + * - Counter + - Description + - Type + + * - `rx_pci_signal_integrity` + - Counts physical layer PCIe signal integrity errors, the number of + transitions to recovery due to Framing errors and CRC (dlp and tlp). If + this counter is raising, try moving the adapter card to a different slot + to rule out a bad PCI slot. Validate that you are running with the latest + firmware available and latest server BIOS version. + - Error + + * - `tx_pci_signal_integrity` + - Counts physical layer PCIe signal integrity errors, the number of + transition to recovery initiated by the other side (moving to recovery + due to getting TS/EIEOS). If this counter is raising, try moving the + adapter card to a different slot to rule out a bad PCI slot. Validate + that you are running with the latest firmware available and latest server + BIOS version. + - Error + + * - `outbound_pci_buffer_overflow` + - The number of packets dropped due to pci buffer overflow. If this counter + is raising in high rate, it might indicate that the receive traffic rate + for a host is larger than the PCIe bus and therefore a congestion occurs. + - Informative + + * - `outbound_pci_stalled_rd` + - The percentage (in the range 0...100) of time within the last second that + the NIC had outbound non-posted reads requests but could not perform the + operation due to insufficient posted credits. + - Informative + + * - `outbound_pci_stalled_wr` + - The percentage (in the range 0...100) of time within the last second that + the NIC had outbound posted writes requests but could not perform the + operation due to insufficient posted credits. + - Informative + + * - `outbound_pci_stalled_rd_events` + - The number of seconds where `outbound_pci_stalled_rd` was above 30%. + - Informative + + * - `outbound_pci_stalled_wr_events` + - The number of seconds where `outbound_pci_stalled_wr` was above 30%. + - Informative + + * - `dev_out_of_buffer` + - The number of times the device owned queue had not enough buffers + allocated. + - Error diff --git a/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/index.rst b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/index.rst new file mode 100644 index 0000000000..581a91caa5 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/index.rst @@ -0,0 +1,25 @@ +.. SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB +.. include:: <isonum.txt> + +Mellanox ConnectX(R) mlx5 core VPI Network Driver +================================================= + +:Copyright: |copy| 2019, Mellanox Technologies LTD. +:Copyright: |copy| 2020-2023, NVIDIA CORPORATION & AFFILIATES. All rights reserved. + +Contents: + +.. toctree:: + :maxdepth: 2 + + kconfig + switchdev + tracepoints + counters + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/kconfig.rst b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/kconfig.rst new file mode 100644 index 0000000000..0a42c3395f --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/kconfig.rst @@ -0,0 +1,168 @@ +.. SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB +.. include:: <isonum.txt> + +======================================= +Enabling the driver and kconfig options +======================================= + +:Copyright: |copy| 2023, NVIDIA CORPORATION & AFFILIATES. All rights reserved. + +| mlx5 core is modular and most of the major mlx5 core driver features can be selected (compiled in/out) +| at build time via kernel Kconfig flags. +| Basic features, ethernet net device rx/tx offloads and XDP, are available with the most basic flags +| CONFIG_MLX5_CORE=y/m and CONFIG_MLX5_CORE_EN=y. +| For the list of advanced features, please see below. + +**CONFIG_MLX5_BRIDGE=(y/n)** + +| Enable :ref:`Ethernet Bridging (BRIDGE) offloading support <mlx5_bridge_offload>`. +| This will provide the ability to add representors of mlx5 uplink and VF +| ports to Bridge and offloading rules for traffic between such ports. +| Supports VLANs (trunk and access modes). + + +**CONFIG_MLX5_CORE=(y/m/n)** (module mlx5_core.ko) + +| The driver can be enabled by choosing CONFIG_MLX5_CORE=y/m in kernel config. +| This will provide mlx5 core driver for mlx5 ulps to interface with (mlx5e, mlx5_ib). + + +**CONFIG_MLX5_CORE_EN=(y/n)** + +| Choosing this option will allow basic ethernet netdevice support with all of the standard rx/tx offloads. +| mlx5e is the mlx5 ulp driver which provides netdevice kernel interface, when chosen, mlx5e will be +| built-in into mlx5_core.ko. + + +**CONFIG_MLX5_CORE_EN_DCB=(y/n)**: + +| Enables `Data Center Bridging (DCB) Support <https://enterprise-support.nvidia.com/s/article/howto-auto-config-pfc-and-ets-on-connectx-4-via-lldp-dcbx>`_. + + +**CONFIG_MLX5_CORE_IPOIB=(y/n)** + +| IPoIB offloads & acceleration support. +| Requires CONFIG_MLX5_CORE_EN to provide an accelerated interface for the rdma +| IPoIB ulp netdevice. + + +**CONFIG_MLX5_CLS_ACT=(y/n)** + +| Enables offload support for TC classifier action (NET_CLS_ACT). +| Works in both native NIC mode and Switchdev SRIOV mode. +| Flow-based classifiers, such as those registered through +| `tc-flower(8)`, are processed by the device, rather than the +| host. Actions that would then overwrite matching classification +| results would then be instant due to the offload. + + +**CONFIG_MLX5_EN_ARFS=(y/n)** + +| Enables Hardware-accelerated receive flow steering (arfs) support, and ntuple filtering. +| https://enterprise-support.nvidia.com/s/article/howto-configure-arfs-on-connectx-4 + + +**CONFIG_MLX5_EN_IPSEC=(y/n)** + +| Enables :ref:`IPSec XFRM cryptography-offload acceleration <xfrm_device>`. + + +**CONFIG_MLX5_EN_MACSEC=(y/n)** + +| Build support for MACsec cryptography-offload acceleration in the NIC. + + +**CONFIG_MLX5_EN_RXNFC=(y/n)** + +| Enables ethtool receive network flow classification, which allows user defined +| flow rules to direct traffic into arbitrary rx queue via ethtool set/get_rxnfc API. + + +**CONFIG_MLX5_EN_TLS=(y/n)** + +| TLS cryptography-offload acceleration. + + +**CONFIG_MLX5_ESWITCH=(y/n)** + +| Ethernet SRIOV E-Switch support in ConnectX NIC. E-Switch provides internal SRIOV packet steering +| and switching for the enabled VFs and PF in two available modes: +| 1) `Legacy SRIOV mode (L2 mac vlan steering based) <https://enterprise-support.nvidia.com/s/article/HowTo-Configure-SR-IOV-for-ConnectX-4-ConnectX-5-ConnectX-6-with-KVM-Ethernet>`_. +| 2) :ref:`Switchdev mode (eswitch offloads) <switchdev>`. + + +**CONFIG_MLX5_FPGA=(y/n)** + +| Build support for the Innova family of network cards by Mellanox Technologies. +| Innova network cards are comprised of a ConnectX chip and an FPGA chip on one board. +| If you select this option, the mlx5_core driver will include the Innova FPGA core and allow +| building sandbox-specific client drivers. + + +**CONFIG_MLX5_INFINIBAND=(y/n/m)** (module mlx5_ib.ko) + +| Provides low-level InfiniBand/RDMA and `RoCE <https://enterprise-support.nvidia.com/s/article/recommended-network-configuration-examples-for-roce-deployment>`_ support. + + +**CONFIG_MLX5_MPFS=(y/n)** + +| Ethernet Multi-Physical Function Switch (MPFS) support in ConnectX NIC. +| MPFs is required for when `Multi-Host <https://www.nvidia.com/en-us/networking/multi-host/>`_ configuration is enabled to allow passing +| user configured unicast MAC addresses to the requesting PF. + + +**CONFIG_MLX5_SF=(y/n)** + +| Build support for subfunction. +| Subfunctons are more light weight than PCI SRIOV VFs. Choosing this option +| will enable support for creating subfunction devices. + + +**CONFIG_MLX5_SF_MANAGER=(y/n)** + +| Build support for subfuction port in the NIC. A Mellanox subfunction +| port is managed through devlink. A subfunction supports RDMA, netdevice +| and vdpa device. It is similar to a SRIOV VF but it doesn't require +| SRIOV support. + + +**CONFIG_MLX5_SW_STEERING=(y/n)** + +| Build support for software-managed steering in the NIC. + + +**CONFIG_MLX5_TC_CT=(y/n)** + +| Support offloading connection tracking rules via tc ct action. + + +**CONFIG_MLX5_TC_SAMPLE=(y/n)** + +| Support offloading sample rules via tc sample action. + + +**CONFIG_MLX5_VDPA=(y/n)** + +| Support library for Mellanox VDPA drivers. Provides code that is +| common for all types of VDPA drivers. The following drivers are planned: +| net, block. + + +**CONFIG_MLX5_VDPA_NET=(y/n)** + +| VDPA network driver for ConnectX6 and newer. Provides offloading +| of virtio net datapath such that descriptors put on the ring will +| be executed by the hardware. It also supports a variety of stateless +| offloads depending on the actual device used and firmware version. + + +**CONFIG_MLX5_VFIO_PCI=(y/n)** + +| This provides migration support for MLX5 devices using the VFIO framework. + + +**External options** ( Choose if the corresponding mlx5 feature is required ) + +- CONFIG_MLXFW: When chosen, mlx5 firmware flashing support will be enabled (via devlink and ethtool). +- CONFIG_PTP_1588_CLOCK: When chosen, mlx5 ptp support will be enabled +- CONFIG_VXLAN: When chosen, mlx5 vxlan support will be enabled. diff --git a/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/switchdev.rst b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/switchdev.rst new file mode 100644 index 0000000000..b617e93d7c --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/switchdev.rst @@ -0,0 +1,281 @@ +.. SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB +.. include:: <isonum.txt> + +========= +Switchdev +========= + +:Copyright: |copy| 2023, NVIDIA CORPORATION & AFFILIATES. All rights reserved. + +.. _mlx5_bridge_offload: + +Bridge offload +============== + +The mlx5 driver implements support for offloading bridge rules when in switchdev +mode. Linux bridge FDBs are automatically offloaded when mlx5 switchdev +representor is attached to bridge. + +- Change device to switchdev mode:: + + $ devlink dev eswitch set pci/0000:06:00.0 mode switchdev + +- Attach mlx5 switchdev representor 'enp8s0f0' to bridge netdev 'bridge1':: + + $ ip link set enp8s0f0 master bridge1 + +VLANs +----- + +Following bridge VLAN functions are supported by mlx5: + +- VLAN filtering (including multiple VLANs per port):: + + $ ip link set bridge1 type bridge vlan_filtering 1 + $ bridge vlan add dev enp8s0f0 vid 2-3 + +- VLAN push on bridge ingress:: + + $ bridge vlan add dev enp8s0f0 vid 3 pvid + +- VLAN pop on bridge egress:: + + $ bridge vlan add dev enp8s0f0 vid 3 untagged + +Subfunction +=========== + +Subfunction which are spawned over the E-switch are created only with devlink +device, and by default all the SF auxiliary devices are disabled. +This will allow user to configure the SF before the SF have been fully probed, +which will save time. + +Usage example: + +- Create SF:: + + $ devlink port add pci/0000:08:00.0 flavour pcisf pfnum 0 sfnum 11 + $ devlink port function set pci/0000:08:00.0/32768 hw_addr 00:00:00:00:00:11 state active + +- Enable ETH auxiliary device:: + + $ devlink dev param set auxiliary/mlx5_core.sf.1 name enable_eth value true cmode driverinit + +- Now, in order to fully probe the SF, use devlink reload:: + + $ devlink dev reload auxiliary/mlx5_core.sf.1 + +mlx5 supports ETH,rdma and vdpa (vnet) auxiliary devices devlink params (see :ref:`Documentation/networking/devlink/devlink-params.rst <devlink_params_generic>`). + +mlx5 supports subfunction management using devlink port (see :ref:`Documentation/networking/devlink/devlink-port.rst <devlink_port>`) interface. + +A subfunction has its own function capabilities and its own resources. This +means a subfunction has its own dedicated queues (txq, rxq, cq, eq). These +queues are neither shared nor stolen from the parent PCI function. + +When a subfunction is RDMA capable, it has its own QP1, GID table, and RDMA +resources neither shared nor stolen from the parent PCI function. + +A subfunction has a dedicated window in PCI BAR space that is not shared +with the other subfunctions or the parent PCI function. This ensures that all +devices (netdev, rdma, vdpa, etc.) of the subfunction accesses only assigned +PCI BAR space. + +A subfunction supports eswitch representation through which it supports tc +offloads. The user configures eswitch to send/receive packets from/to +the subfunction port. + +Subfunctions share PCI level resources such as PCI MSI-X IRQs with +other subfunctions and/or with its parent PCI function. + +Example mlx5 software, system, and device view:: + + _______ + | admin | + | user |---------- + |_______| | + | | + ____|____ __|______ _________________ + | | | | | | + | devlink | | tc tool | | user | + | tool | |_________| | applications | + |_________| | |_________________| + | | | | + | | | | Userspace + +---------|-------------|-------------------|----------|--------------------+ + | | +----------+ +----------+ Kernel + | | | netdev | | rdma dev | + | | +----------+ +----------+ + (devlink port add/del | ^ ^ + port function set) | | | + | | +---------------| + _____|___ | | _______|_______ + | | | | | mlx5 class | + | devlink | +------------+ | | drivers | + | kernel | | rep netdev | | |(mlx5_core,ib) | + |_________| +------------+ | |_______________| + | | | ^ + (devlink ops) | | (probe/remove) + _________|________ | | ____|________ + | subfunction | | +---------------+ | subfunction | + | management driver|----- | subfunction |---| driver | + | (mlx5_core) | | auxiliary dev | | (mlx5_core) | + |__________________| +---------------+ |_____________| + | ^ + (sf add/del, vhca events) | + | (device add/del) + _____|____ ____|________ + | | | subfunction | + | PCI NIC |--- activate/deactivate events--->| host driver | + |__________| | (mlx5_core) | + |_____________| + +Subfunction is created using devlink port interface. + +- Change device to switchdev mode:: + + $ devlink dev eswitch set pci/0000:06:00.0 mode switchdev + +- Add a devlink port of subfunction flavour:: + + $ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88 + pci/0000:06:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false + function: + hw_addr 00:00:00:00:00:00 state inactive opstate detached + +- Show a devlink port of the subfunction:: + + $ devlink port show pci/0000:06:00.0/32768 + pci/0000:06:00.0/32768: type eth netdev enp6s0pf0sf88 flavour pcisf pfnum 0 sfnum 88 + function: + hw_addr 00:00:00:00:00:00 state inactive opstate detached + +- Delete a devlink port of subfunction after use:: + + $ devlink port del pci/0000:06:00.0/32768 + +Function attributes +=================== + +The mlx5 driver provides a mechanism to setup PCI VF/SF function attributes in +a unified way for SmartNIC and non-SmartNIC. + +This is supported only when the eswitch mode is set to switchdev. Port function +configuration of the PCI VF/SF is supported through devlink eswitch port. + +Port function attributes should be set before PCI VF/SF is enumerated by the +driver. + +MAC address setup +----------------- + +mlx5 driver support devlink port function attr mechanism to setup MAC +address. (refer to Documentation/networking/devlink/devlink-port.rst) + +RoCE capability setup +~~~~~~~~~~~~~~~~~~~~~ +Not all mlx5 PCI devices/SFs require RoCE capability. + +When RoCE capability is disabled, it saves 1 Mbytes worth of system memory per +PCI devices/SF. + +mlx5 driver support devlink port function attr mechanism to setup RoCE +capability. (refer to Documentation/networking/devlink/devlink-port.rst) + +migratable capability setup +~~~~~~~~~~~~~~~~~~~~~~~~~~~ +User who wants mlx5 PCI VFs to be able to perform live migration need to +explicitly enable the VF migratable capability. + +mlx5 driver support devlink port function attr mechanism to setup migratable +capability. (refer to Documentation/networking/devlink/devlink-port.rst) + +IPsec crypto capability setup +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +User who wants mlx5 PCI VFs to be able to perform IPsec crypto offloading need +to explicitly enable the VF ipsec_crypto capability. Enabling IPsec capability +for VFs is supported starting with ConnectX6dx devices and above. When a VF has +IPsec capability enabled, any IPsec offloading is blocked on the PF. + +mlx5 driver support devlink port function attr mechanism to setup ipsec_crypto +capability. (refer to Documentation/networking/devlink/devlink-port.rst) + +IPsec packet capability setup +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +User who wants mlx5 PCI VFs to be able to perform IPsec packet offloading need +to explicitly enable the VF ipsec_packet capability. Enabling IPsec capability +for VFs is supported starting with ConnectX6dx devices and above. When a VF has +IPsec capability enabled, any IPsec offloading is blocked on the PF. + +mlx5 driver support devlink port function attr mechanism to setup ipsec_packet +capability. (refer to Documentation/networking/devlink/devlink-port.rst) + +SF state setup +-------------- + +To use the SF, the user must activate the SF using the SF function state +attribute. + +- Get the state of the SF identified by its unique devlink port index:: + + $ devlink port show ens2f0npf0sf88 + pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false + function: + hw_addr 00:00:00:00:88:88 state inactive opstate detached + +- Activate the function and verify its state is active:: + + $ devlink port function set ens2f0npf0sf88 state active + + $ devlink port show ens2f0npf0sf88 + pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false + function: + hw_addr 00:00:00:00:88:88 state active opstate detached + +Upon function activation, the PF driver instance gets the event from the device +that a particular SF was activated. It's the cue to put the device on bus, probe +it and instantiate the devlink instance and class specific auxiliary devices +for it. + +- Show the auxiliary device and port of the subfunction:: + + $ devlink dev show + devlink dev show auxiliary/mlx5_core.sf.4 + + $ devlink port show auxiliary/mlx5_core.sf.4/1 + auxiliary/mlx5_core.sf.4/1: type eth netdev p0sf88 flavour virtual port 0 splittable false + + $ rdma link show mlx5_0/1 + link mlx5_0/1 state ACTIVE physical_state LINK_UP netdev p0sf88 + + $ rdma dev show + 8: rocep6s0f1: node_type ca fw 16.29.0550 node_guid 248a:0703:00b3:d113 sys_image_guid 248a:0703:00b3:d112 + 13: mlx5_0: node_type ca fw 16.29.0550 node_guid 0000:00ff:fe00:8888 sys_image_guid 248a:0703:00b3:d112 + +- Subfunction auxiliary device and class device hierarchy:: + + mlx5_core.sf.4 + (subfunction auxiliary device) + /\ + / \ + / \ + / \ + / \ + mlx5_core.eth.4 mlx5_core.rdma.4 + (sf eth aux dev) (sf rdma aux dev) + | | + | | + p0sf88 mlx5_0 + (sf netdev) (sf rdma device) + +Additionally, the SF port also gets the event when the driver attaches to the +auxiliary device of the subfunction. This results in changing the operational +state of the function. This provides visibility to the user to decide when is it +safe to delete the SF port for graceful termination of the subfunction. + +- Show the SF port operational state:: + + $ devlink port show ens2f0npf0sf88 + pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false + function: + hw_addr 00:00:00:00:88:88 state active opstate attached diff --git a/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/tracepoints.rst b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/tracepoints.rst new file mode 100644 index 0000000000..da8e53cebb --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/mellanox/mlx5/tracepoints.rst @@ -0,0 +1,229 @@ +.. SPDX-License-Identifier: GPL-2.0 OR Linux-OpenIB +.. include:: <isonum.txt> + +=========== +Tracepoints +=========== + +:Copyright: |copy| 2023, NVIDIA CORPORATION & AFFILIATES. All rights reserved. + +mlx5 driver provides internal tracepoints for tracking and debugging using +kernel tracepoints interfaces (refer to Documentation/trace/ftrace.rst). + +For the list of support mlx5 events, check /sys/kernel/tracing/events/mlx5/. + +tc and eswitch offloads tracepoints: + +- mlx5e_configure_flower: trace flower filter actions and cookies offloaded to mlx5:: + + $ echo mlx5:mlx5e_configure_flower >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + tc-6535 [019] ...1 2672.404466: mlx5e_configure_flower: cookie=0000000067874a55 actions= REDIRECT + +- mlx5e_delete_flower: trace flower filter actions and cookies deleted from mlx5:: + + $ echo mlx5:mlx5e_delete_flower >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + tc-6569 [010] .N.1 2686.379075: mlx5e_delete_flower: cookie=0000000067874a55 actions= NULL + +- mlx5e_stats_flower: trace flower stats request:: + + $ echo mlx5:mlx5e_stats_flower >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + tc-6546 [010] ...1 2679.704889: mlx5e_stats_flower: cookie=0000000060eb3d6a bytes=0 packets=0 lastused=4295560217 + +- mlx5e_tc_update_neigh_used_value: trace tunnel rule neigh update value offloaded to mlx5:: + + $ echo mlx5:mlx5e_tc_update_neigh_used_value >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + kworker/u48:4-8806 [009] ...1 55117.882428: mlx5e_tc_update_neigh_used_value: netdev: ens1f0 IPv4: 1.1.1.10 IPv6: ::ffff:1.1.1.10 neigh_used=1 + +- mlx5e_rep_neigh_update: trace neigh update tasks scheduled due to neigh state change events:: + + $ echo mlx5:mlx5e_rep_neigh_update >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + kworker/u48:7-2221 [009] ...1 1475.387435: mlx5e_rep_neigh_update: netdev: ens1f0 MAC: 24:8a:07:9a:17:9a IPv4: 1.1.1.10 IPv6: ::ffff:1.1.1.10 neigh_connected=1 + +Bridge offloads tracepoints: + +- mlx5_esw_bridge_fdb_entry_init: trace bridge FDB entry offloaded to mlx5:: + + $ echo mlx5:mlx5_esw_bridge_fdb_entry_init >> set_event + $ cat /sys/kernel/tracing/trace + ... + kworker/u20:9-2217 [003] ...1 318.582243: mlx5_esw_bridge_fdb_entry_init: net_device=enp8s0f0_0 addr=e4:fd:05:08:00:02 vid=0 flags=0 used=0 + +- mlx5_esw_bridge_fdb_entry_cleanup: trace bridge FDB entry deleted from mlx5:: + + $ echo mlx5:mlx5_esw_bridge_fdb_entry_cleanup >> set_event + $ cat /sys/kernel/tracing/trace + ... + ip-2581 [005] ...1 318.629871: mlx5_esw_bridge_fdb_entry_cleanup: net_device=enp8s0f0_1 addr=e4:fd:05:08:00:03 vid=0 flags=0 used=16 + +- mlx5_esw_bridge_fdb_entry_refresh: trace bridge FDB entry offload refreshed in + mlx5:: + + $ echo mlx5:mlx5_esw_bridge_fdb_entry_refresh >> set_event + $ cat /sys/kernel/tracing/trace + ... + kworker/u20:8-3849 [003] ...1 466716: mlx5_esw_bridge_fdb_entry_refresh: net_device=enp8s0f0_0 addr=e4:fd:05:08:00:02 vid=3 flags=0 used=0 + +- mlx5_esw_bridge_vlan_create: trace bridge VLAN object add on mlx5 + representor:: + + $ echo mlx5:mlx5_esw_bridge_vlan_create >> set_event + $ cat /sys/kernel/tracing/trace + ... + ip-2560 [007] ...1 318.460258: mlx5_esw_bridge_vlan_create: vid=1 flags=6 + +- mlx5_esw_bridge_vlan_cleanup: trace bridge VLAN object delete from mlx5 + representor:: + + $ echo mlx5:mlx5_esw_bridge_vlan_cleanup >> set_event + $ cat /sys/kernel/tracing/trace + ... + bridge-2582 [007] ...1 318.653496: mlx5_esw_bridge_vlan_cleanup: vid=2 flags=8 + +- mlx5_esw_bridge_vport_init: trace mlx5 vport assigned with bridge upper + device:: + + $ echo mlx5:mlx5_esw_bridge_vport_init >> set_event + $ cat /sys/kernel/tracing/trace + ... + ip-2560 [007] ...1 318.458915: mlx5_esw_bridge_vport_init: vport_num=1 + +- mlx5_esw_bridge_vport_cleanup: trace mlx5 vport removed from bridge upper + device:: + + $ echo mlx5:mlx5_esw_bridge_vport_cleanup >> set_event + $ cat /sys/kernel/tracing/trace + ... + ip-5387 [000] ...1 573713: mlx5_esw_bridge_vport_cleanup: vport_num=1 + +Eswitch QoS tracepoints: + +- mlx5_esw_vport_qos_create: trace creation of transmit scheduler arbiter for vport:: + + $ echo mlx5:mlx5_esw_vport_qos_create >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + <...>-23496 [018] .... 73136.838831: mlx5_esw_vport_qos_create: (0000:82:00.0) vport=2 tsar_ix=4 bw_share=0, max_rate=0 group=000000007b576bb3 + +- mlx5_esw_vport_qos_config: trace configuration of transmit scheduler arbiter for vport:: + + $ echo mlx5:mlx5_esw_vport_qos_config >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + <...>-26548 [023] .... 75754.223823: mlx5_esw_vport_qos_config: (0000:82:00.0) vport=1 tsar_ix=3 bw_share=34, max_rate=10000 group=000000007b576bb3 + +- mlx5_esw_vport_qos_destroy: trace deletion of transmit scheduler arbiter for vport:: + + $ echo mlx5:mlx5_esw_vport_qos_destroy >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + <...>-27418 [004] .... 76546.680901: mlx5_esw_vport_qos_destroy: (0000:82:00.0) vport=1 tsar_ix=3 + +- mlx5_esw_group_qos_create: trace creation of transmit scheduler arbiter for rate group:: + + $ echo mlx5:mlx5_esw_group_qos_create >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + <...>-26578 [008] .... 75776.022112: mlx5_esw_group_qos_create: (0000:82:00.0) group=000000008dac63ea tsar_ix=5 + +- mlx5_esw_group_qos_config: trace configuration of transmit scheduler arbiter for rate group:: + + $ echo mlx5:mlx5_esw_group_qos_config >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + <...>-27303 [020] .... 76461.455356: mlx5_esw_group_qos_config: (0000:82:00.0) group=000000008dac63ea tsar_ix=5 bw_share=100 max_rate=20000 + +- mlx5_esw_group_qos_destroy: trace deletion of transmit scheduler arbiter for group:: + + $ echo mlx5:mlx5_esw_group_qos_destroy >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + <...>-27418 [006] .... 76547.187258: mlx5_esw_group_qos_destroy: (0000:82:00.0) group=000000007b576bb3 tsar_ix=1 + +SF tracepoints: + +- mlx5_sf_add: trace addition of the SF port:: + + $ echo mlx5:mlx5_sf_add >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + devlink-9363 [031] ..... 24610.188722: mlx5_sf_add: (0000:06:00.0) port_index=32768 controller=0 hw_id=0x8000 sfnum=88 + +- mlx5_sf_free: trace freeing of the SF port:: + + $ echo mlx5:mlx5_sf_free >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + devlink-9830 [038] ..... 26300.404749: mlx5_sf_free: (0000:06:00.0) port_index=32768 controller=0 hw_id=0x8000 + +- mlx5_sf_activate: trace activation of the SF port:: + + $ echo mlx5:mlx5_sf_activate >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + devlink-29841 [008] ..... 3669.635095: mlx5_sf_activate: (0000:08:00.0) port_index=32768 controller=0 hw_id=0x8000 + +- mlx5_sf_deactivate: trace deactivation of the SF port:: + + $ echo mlx5:mlx5_sf_deactivate >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + devlink-29994 [008] ..... 4015.969467: mlx5_sf_deactivate: (0000:08:00.0) port_index=32768 controller=0 hw_id=0x8000 + +- mlx5_sf_hwc_alloc: trace allocating of the hardware SF context:: + + $ echo mlx5:mlx5_sf_hwc_alloc >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + devlink-9775 [031] ..... 26296.385259: mlx5_sf_hwc_alloc: (0000:06:00.0) controller=0 hw_id=0x8000 sfnum=88 + +- mlx5_sf_hwc_free: trace freeing of the hardware SF context:: + + $ echo mlx5:mlx5_sf_hwc_free >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + kworker/u128:3-9093 [046] ..... 24625.365771: mlx5_sf_hwc_free: (0000:06:00.0) hw_id=0x8000 + +- mlx5_sf_hwc_deferred_free: trace deferred freeing of the hardware SF context:: + + $ echo mlx5:mlx5_sf_hwc_deferred_free >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + devlink-9519 [046] ..... 24624.400271: mlx5_sf_hwc_deferred_free: (0000:06:00.0) hw_id=0x8000 + +- mlx5_sf_update_state: trace state updates for SF contexts:: + + $ echo mlx5:mlx5_sf_update_state >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + kworker/u20:3-29490 [009] ..... 4141.453530: mlx5_sf_update_state: (0000:08:00.0) port_index=32768 controller=0 hw_id=0x8000 state=2 + +- mlx5_sf_vhca_event: trace SF vhca event and state:: + + $ echo mlx5:mlx5_sf_vhca_event >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + kworker/u128:3-9093 [046] ..... 24625.365525: mlx5_sf_vhca_event: (0000:06:00.0) hw_id=0x8000 sfnum=88 vhca_state=1 + +- mlx5_sf_dev_add: trace SF device add event:: + + $ echo mlx5:mlx5_sf_dev_add>> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + kworker/u128:3-9093 [000] ..... 24616.524495: mlx5_sf_dev_add: (0000:06:00.0) sfdev=00000000fc5d96fd aux_id=4 hw_id=0x8000 sfnum=88 + +- mlx5_sf_dev_del: trace SF device delete event:: + + $ echo mlx5:mlx5_sf_dev_del >> /sys/kernel/tracing/set_event + $ cat /sys/kernel/tracing/trace + ... + kworker/u128:3-9093 [044] ..... 24624.400749: mlx5_sf_dev_del: (0000:06:00.0) sfdev=00000000fc5d96fd aux_id=4 hw_id=0x8000 sfnum=88 diff --git a/Documentation/networking/device_drivers/ethernet/microsoft/netvsc.rst b/Documentation/networking/device_drivers/ethernet/microsoft/netvsc.rst new file mode 100644 index 0000000000..fc5acd427a --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/microsoft/netvsc.rst @@ -0,0 +1,120 @@ +.. SPDX-License-Identifier: GPL-2.0 + +====================== +Hyper-V network driver +====================== + +Compatibility +============= + +This driver is compatible with Windows Server 2012 R2, 2016 and +Windows 10. + +Features +======== + +Checksum offload +---------------- + The netvsc driver supports checksum offload as long as the + Hyper-V host version does. Windows Server 2016 and Azure + support checksum offload for TCP and UDP for both IPv4 and + IPv6. Windows Server 2012 only supports checksum offload for TCP. + +Receive Side Scaling +-------------------- + Hyper-V supports receive side scaling. For TCP & UDP, packets can + be distributed among available queues based on IP address and port + number. + + For TCP & UDP, we can switch hash level between L3 and L4 by ethtool + command. TCP/UDP over IPv4 and v6 can be set differently. The default + hash level is L4. We currently only allow switching TX hash level + from within the guests. + + On Azure, fragmented UDP packets have high loss rate with L4 + hashing. Using L3 hashing is recommended in this case. + + For example, for UDP over IPv4 on eth0: + + To include UDP port numbers in hashing:: + + ethtool -N eth0 rx-flow-hash udp4 sdfn + + To exclude UDP port numbers in hashing:: + + ethtool -N eth0 rx-flow-hash udp4 sd + + To show UDP hash level:: + + ethtool -n eth0 rx-flow-hash udp4 + +Generic Receive Offload, aka GRO +-------------------------------- + The driver supports GRO and it is enabled by default. GRO coalesces + like packets and significantly reduces CPU usage under heavy Rx + load. + +Large Receive Offload (LRO), or Receive Side Coalescing (RSC) +------------------------------------------------------------- + The driver supports LRO/RSC in the vSwitch feature. It reduces the per packet + processing overhead by coalescing multiple TCP segments when possible. The + feature is enabled by default on VMs running on Windows Server 2019 and + later. It may be changed by ethtool command:: + + ethtool -K eth0 lro on + ethtool -K eth0 lro off + +SR-IOV support +-------------- + Hyper-V supports SR-IOV as a hardware acceleration option. If SR-IOV + is enabled in both the vSwitch and the guest configuration, then the + Virtual Function (VF) device is passed to the guest as a PCI + device. In this case, both a synthetic (netvsc) and VF device are + visible in the guest OS and both NIC's have the same MAC address. + + The VF is enslaved by netvsc device. The netvsc driver will transparently + switch the data path to the VF when it is available and up. + Network state (addresses, firewall, etc) should be applied only to the + netvsc device; the slave device should not be accessed directly in + most cases. The exceptions are if some special queue discipline or + flow direction is desired, these should be applied directly to the + VF slave device. + +Receive Buffer +-------------- + Packets are received into a receive area which is created when device + is probed. The receive area is broken into MTU sized chunks and each may + contain one or more packets. The number of receive sections may be changed + via ethtool Rx ring parameters. + + There is a similar send buffer which is used to aggregate packets + for sending. The send area is broken into chunks, typically of 6144 + bytes, each of section may contain one or more packets. Small + packets are usually transmitted via copy to the send buffer. However, + if the buffer is temporarily exhausted, or the packet to be transmitted is + an LSO packet, the driver will provide the host with pointers to the data + from the SKB. This attempts to achieve a balance between the overhead of + data copy and the impact of remapping VM memory to be accessible by the + host. + +XDP support +----------- + XDP (eXpress Data Path) is a feature that runs eBPF bytecode at the early + stage when packets arrive at a NIC card. The goal is to increase performance + for packet processing, reducing the overhead of SKB allocation and other + upper network layers. + + hv_netvsc supports XDP in native mode, and transparently sets the XDP + program on the associated VF NIC as well. + + Setting / unsetting XDP program on synthetic NIC (netvsc) propagates to + VF NIC automatically. Setting / unsetting XDP program on VF NIC directly + is not recommended, also not propagated to synthetic NIC, and may be + overwritten by setting of synthetic NIC. + + XDP program cannot run with LRO (RSC) enabled, so you need to disable LRO + before running XDP:: + + ethtool -K eth0 lro off + + XDP_REDIRECT action is not yet supported. diff --git a/Documentation/networking/device_drivers/ethernet/neterion/s2io.rst b/Documentation/networking/device_drivers/ethernet/neterion/s2io.rst new file mode 100644 index 0000000000..c5673ec455 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/neterion/s2io.rst @@ -0,0 +1,196 @@ +.. SPDX-License-Identifier: GPL-2.0 + +========================================================= +Neterion's (Formerly S2io) Xframe I/II PCI-X 10GbE driver +========================================================= + +Release notes for Neterion's (Formerly S2io) Xframe I/II PCI-X 10GbE driver. + +.. Contents + - 1. Introduction + - 2. Identifying the adapter/interface + - 3. Features supported + - 4. Command line parameters + - 5. Performance suggestions + - 6. Available Downloads + + +1. Introduction +=============== +This Linux driver supports Neterion's Xframe I PCI-X 1.0 and +Xframe II PCI-X 2.0 adapters. It supports several features +such as jumbo frames, MSI/MSI-X, checksum offloads, TSO, UFO and so on. +See below for complete list of features. + +All features are supported for both IPv4 and IPv6. + +2. Identifying the adapter/interface +==================================== + +a. Insert the adapter(s) in your system. +b. Build and load driver:: + + # insmod s2io.ko + +c. View log messages:: + + # dmesg | tail -40 + +You will see messages similar to:: + + eth3: Neterion Xframe I 10GbE adapter (rev 3), Version 2.0.9.1, Intr type INTA + eth4: Neterion Xframe II 10GbE adapter (rev 2), Version 2.0.9.1, Intr type INTA + eth4: Device is on 64 bit 133MHz PCIX(M1) bus + +The above messages identify the adapter type(Xframe I/II), adapter revision, +driver version, interface name(eth3, eth4), Interrupt type(INTA, MSI, MSI-X). +In case of Xframe II, the PCI/PCI-X bus width and frequency are displayed +as well. + +To associate an interface with a physical adapter use "ethtool -p <ethX>". +The corresponding adapter's LED will blink multiple times. + +3. Features supported +===================== +a. Jumbo frames. Xframe I/II supports MTU up to 9600 bytes, + modifiable using ip command. + +b. Offloads. Supports checksum offload(TCP/UDP/IP) on transmit + and receive, TSO. + +c. Multi-buffer receive mode. Scattering of packet across multiple + buffers. Currently driver supports 2-buffer mode which yields + significant performance improvement on certain platforms(SGI Altix, + IBM xSeries). + +d. MSI/MSI-X. Can be enabled on platforms which support this feature + (IA64, Xeon) resulting in noticeable performance improvement(up to 7% + on certain platforms). + +e. Statistics. Comprehensive MAC-level and software statistics displayed + using "ethtool -S" option. + +f. Multi-FIFO/Ring. Supports up to 8 transmit queues and receive rings, + with multiple steering options. + +4. Command line parameters +========================== + +a. tx_fifo_num + Number of transmit queues + +Valid range: 1-8 + +Default: 1 + +b. rx_ring_num + Number of receive rings + +Valid range: 1-8 + +Default: 1 + +c. tx_fifo_len + Size of each transmit queue + +Valid range: Total length of all queues should not exceed 8192 + +Default: 4096 + +d. rx_ring_sz + Size of each receive ring(in 4K blocks) + +Valid range: Limited by memory on system + +Default: 30 + +e. intr_type + Specifies interrupt type. Possible values 0(INTA), 2(MSI-X) + +Valid values: 0, 2 + +Default: 2 + +5. Performance suggestions +========================== + +General: + +a. Set MTU to maximum(9000 for switch setup, 9600 in back-to-back configuration) +b. Set TCP windows size to optimal value. + +For instance, for MTU=1500 a value of 210K has been observed to result in +good performance:: + + # sysctl -w net.ipv4.tcp_rmem="210000 210000 210000" + # sysctl -w net.ipv4.tcp_wmem="210000 210000 210000" + +For MTU=9000, TCP window size of 10 MB is recommended:: + + # sysctl -w net.ipv4.tcp_rmem="10000000 10000000 10000000" + # sysctl -w net.ipv4.tcp_wmem="10000000 10000000 10000000" + +Transmit performance: + +a. By default, the driver respects BIOS settings for PCI bus parameters. + However, you may want to experiment with PCI bus parameters + max-split-transactions(MOST) and MMRBC (use setpci command). + + A MOST value of 2 has been found optimal for Opterons and 3 for Itanium. + + It could be different for your hardware. + + Set MMRBC to 4K**. + + For example you can set + + For opteron:: + + #setpci -d 17d5:* 62=1d + + For Itanium:: + + #setpci -d 17d5:* 62=3d + + For detailed description of the PCI registers, please see Xframe User Guide. + +b. Ensure Transmit Checksum offload is enabled. Use ethtool to set/verify this + parameter. + +c. Turn on TSO(using "ethtool -K"):: + + # ethtool -K <ethX> tso on + +Receive performance: + +a. By default, the driver respects BIOS settings for PCI bus parameters. + However, you may want to set PCI latency timer to 248:: + + #setpci -d 17d5:* LATENCY_TIMER=f8 + + For detailed description of the PCI registers, please see Xframe User Guide. + +b. Use 2-buffer mode. This results in large performance boost on + certain platforms(eg. SGI Altix, IBM xSeries). + +c. Ensure Receive Checksum offload is enabled. Use "ethtool -K ethX" command to + set/verify this option. + +d. Enable NAPI feature(in kernel configuration Device Drivers ---> Network + device support ---> Ethernet (10000 Mbit) ---> S2IO 10Gbe Xframe NIC) to + bring down CPU utilization. + +.. note:: + + For AMD opteron platforms with 8131 chipset, MMRBC=1 and MOST=1 are + recommended as safe parameters. + +For more information, please review the AMD8131 errata at +http://vip.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/ +26310_AMD-8131_HyperTransport_PCI-X_Tunnel_Revision_Guide_rev_3_18.pdf + +6. Support +========== + +For further support please contact either your 10GbE Xframe NIC vendor (IBM, +HP, SGI etc.) diff --git a/Documentation/networking/device_drivers/ethernet/netronome/nfp.rst b/Documentation/networking/device_drivers/ethernet/netronome/nfp.rst new file mode 100644 index 0000000000..650b57742d --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/netronome/nfp.rst @@ -0,0 +1,374 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +.. include:: <isonum.txt> + +=========================================== +Network Flow Processor (NFP) Kernel Drivers +=========================================== + +:Copyright: |copy| 2019, Netronome Systems, Inc. +:Copyright: |copy| 2022, Corigine, Inc. + +Contents +======== + +- `Overview`_ +- `Acquiring Firmware`_ +- `Devlink Info`_ +- `Configure Device`_ +- `Statistics`_ + +Overview +======== + +This driver supports Netronome and Corigine's line of Network Flow Processor +devices, including the NFP3800, NFP4000, NFP5000, and NFP6000 models, which +are also incorporated in the companies' family of Agilio SmartNICs. The SR-IOV +physical and virtual functions for these devices are supported by the driver. + +Acquiring Firmware +================== + +The NFP3800, NFP4000 and NFP6000 devices require application specific firmware +to function. Application firmware can be located either on the host file system +or in the device flash (if supported by management firmware). + +Firmware files on the host filesystem contain card type (`AMDA-*` string), media +config etc. They should be placed in `/lib/firmware/netronome` directory to +load firmware from the host file system. + +Firmware for basic NIC operation is available in the upstream +`linux-firmware.git` repository. + +A more comprehensive list of firmware can be downloaded from the +`Corigine Support site <https://www.corigine.com/DPUDownload.html>`_. + +Firmware in NVRAM +----------------- + +Recent versions of management firmware supports loading application +firmware from flash when the host driver gets probed. The firmware loading +policy configuration may be used to configure this feature appropriately. + +Devlink or ethtool can be used to update the application firmware on the device +flash by providing the appropriate `nic_AMDA*.nffw` file to the respective +command. Users need to take care to write the correct firmware image for the +card and media configuration to flash. + +Available storage space in flash depends on the card being used. + +Dealing with multiple projects +------------------------------ + +NFP hardware is fully programmable therefore there can be different +firmware images targeting different applications. + +When using application firmware from host, we recommend placing +actual firmware files in application-named subdirectories in +`/lib/firmware/netronome` and linking the desired files, e.g.:: + + $ tree /lib/firmware/netronome/ + /lib/firmware/netronome/ + ├── bpf + │ ├── nic_AMDA0081-0001_1x40.nffw + │ └── nic_AMDA0081-0001_4x10.nffw + ├── flower + │ ├── nic_AMDA0081-0001_1x40.nffw + │ └── nic_AMDA0081-0001_4x10.nffw + ├── nic + │ ├── nic_AMDA0081-0001_1x40.nffw + │ └── nic_AMDA0081-0001_4x10.nffw + ├── nic_AMDA0081-0001_1x40.nffw -> bpf/nic_AMDA0081-0001_1x40.nffw + └── nic_AMDA0081-0001_4x10.nffw -> bpf/nic_AMDA0081-0001_4x10.nffw + + 3 directories, 8 files + +You may need to use hard instead of symbolic links on distributions +which use old `mkinitrd` command instead of `dracut` (e.g. Ubuntu). + +After changing firmware files you may need to regenerate the initramfs +image. Initramfs contains drivers and firmware files your system may +need to boot. Refer to the documentation of your distribution to find +out how to update initramfs. Good indication of stale initramfs +is system loading wrong driver or firmware on boot, but when driver is +later reloaded manually everything works correctly. + +Selecting firmware per device +----------------------------- + +Most commonly all cards on the system use the same type of firmware. +If you want to load a specific firmware image for a specific card, you +can use either the PCI bus address or serial number. The driver will +print which files it's looking for when it recognizes a NFP device:: + + nfp: Looking for firmware file in order of priority: + nfp: netronome/serial-00-12-34-aa-bb-cc-10-ff.nffw: not found + nfp: netronome/pci-0000:02:00.0.nffw: not found + nfp: netronome/nic_AMDA0081-0001_1x40.nffw: found, loading... + +In this case if file (or link) called *serial-00-12-34-aa-bb-5d-10-ff.nffw* +or *pci-0000:02:00.0.nffw* is present in `/lib/firmware/netronome` this +firmware file will take precedence over `nic_AMDA*` files. + +Note that `serial-*` and `pci-*` files are **not** automatically included +in initramfs, you will have to refer to documentation of appropriate tools +to find out how to include them. + +Running firmware version +------------------------ + +The version of the loaded firmware for a particular <netdev> interface, +(e.g. enp4s0), or an interface's port <netdev port> (e.g. enp4s0np0) can +be displayed with the ethtool command:: + + $ ethtool -i <netdev> + +Firmware loading policy +----------------------- + +Firmware loading policy is controlled via three HWinfo parameters +stored as key value pairs in the device flash: + +app_fw_from_flash + Defines which firmware should take precedence, 'Disk' (0), 'Flash' (1) or + the 'Preferred' (2) firmware. When 'Preferred' is selected, the management + firmware makes the decision over which firmware will be loaded by comparing + versions of the flash firmware and the host supplied firmware. + This variable is configurable using the 'fw_load_policy' + devlink parameter. + +abi_drv_reset + Defines if the driver should reset the firmware when + the driver is probed, either 'Disk' (0) if firmware was found on disk, + 'Always' (1) reset or 'Never' (2) reset. Note that the device is always + reset on driver unload if firmware was loaded when the driver was probed. + This variable is configurable using the 'reset_dev_on_drv_probe' + devlink parameter. + +abi_drv_load_ifc + Defines a list of PF devices allowed to load FW on the device. + This variable is not currently user configurable. + +Devlink Info +============ + +The devlink info command displays the running and stored firmware versions +on the device, serial number and board information. + +Devlink info command example (replace PCI address):: + + $ devlink dev info pci/0000:03:00.0 + pci/0000:03:00.0: + driver nfp + serial_number CSAAMDA2001-1003000111 + versions: + fixed: + board.id AMDA2001-1003 + board.rev 01 + board.manufacture CSA + board.model mozart + running: + fw.mgmt 22.10.0-rc3 + fw.cpld 0x1000003 + fw.app nic-22.09.0 + chip.init AMDA-2001-1003 1003000111 + stored: + fw.bundle_id bspbundle_1003000111 + fw.mgmt 22.10.0-rc3 + fw.cpld 0x0 + chip.init AMDA-2001-1003 1003000111 + +Configure Device +================ + +This section explains how to use Agilio SmartNICs running basic NIC firmware. + +Configure interface link-speed +------------------------------ +The following steps explains how to change between 10G mode and 25G mode on +Agilio CX 2x25GbE cards. The changing of port speed must be done in order, +port 0 (p0) must be set to 10G before port 1 (p1) may be set to 10G. + +Down the respective interface(s):: + + $ ip link set dev <netdev port 0> down + $ ip link set dev <netdev port 1> down + +Set interface link-speed to 10G:: + + $ ethtool -s <netdev port 0> speed 10000 + $ ethtool -s <netdev port 1> speed 10000 + +Set interface link-speed to 25G:: + + $ ethtool -s <netdev port 0> speed 25000 + $ ethtool -s <netdev port 1> speed 25000 + +Reload driver for changes to take effect:: + + $ rmmod nfp; modprobe nfp + +Configure interface Maximum Transmission Unit (MTU) +--------------------------------------------------- + +The MTU of interfaces can temporarily be set using the iproute2, ip link or +ifconfig tools. Note that this change will not persist. Setting this via +Network Manager, or another appropriate OS configuration tool, is +recommended as changes to the MTU using Network Manager can be made to +persist. + +Set interface MTU to 9000 bytes:: + + $ ip link set dev <netdev port> mtu 9000 + +It is the responsibility of the user or the orchestration layer to set +appropriate MTU values when handling jumbo frames or utilizing tunnels. For +example, if packets sent from a VM are to be encapsulated on the card and +egress a physical port, then the MTU of the VF should be set to lower than +that of the physical port to account for the extra bytes added by the +additional header. If a setup is expected to see fallback traffic between +the SmartNIC and the kernel then the user should also ensure that the PF MTU +is appropriately set to avoid unexpected drops on this path. + +Configure Forward Error Correction (FEC) modes +---------------------------------------------- + +Agilio SmartNICs support FEC mode configuration, e.g. Auto, Firecode Base-R, +ReedSolomon and Off modes. Each physical port's FEC mode can be set +independently using ethtool. The supported FEC modes for an interface can +be viewed using:: + + $ ethtool <netdev> + +The currently configured FEC mode can be viewed using:: + + $ ethtool --show-fec <netdev> + +To force the FEC mode for a particular port, auto-negotiation must be disabled +(see the `Auto-negotiation`_ section). An example of how to set the FEC mode +to Reed-Solomon is:: + + $ ethtool --set-fec <netdev> encoding rs + +Auto-negotiation +---------------- + +To change auto-negotiation settings, the link must first be put down. After the +link is down, auto-negotiation can be enabled or disabled using:: + + ethtool -s <netdev> autoneg <on|off> + +Statistics +========== + +Following device statistics are available through the ``ethtool -S`` interface: + +.. flat-table:: NFP device statistics + :header-rows: 1 + :widths: 3 1 11 + + * - Name + - ID + - Meaning + + * - dev_rx_discards + - 1 + - Packet can be discarded on the RX path for one of the following reasons: + + * The NIC is not in promisc mode, and the destination MAC address + doesn't match the interfaces' MAC address. + * The received packet is larger than the max buffer size on the host. + I.e. it exceeds the Layer 3 MRU. + * There is no freelist descriptor available on the host for the packet. + It is likely that the NIC couldn't cache one in time. + * A BPF program discarded the packet. + * The datapath drop action was executed. + * The MAC discarded the packet due to lack of ingress buffer space + on the NIC. + + * - dev_rx_errors + - 2 + - A packet can be counted (and dropped) as RX error for the following + reasons: + + * A problem with the VEB lookup (only when SR-IOV is used). + * A physical layer problem that causes Ethernet errors, like FCS or + alignment errors. The cause is usually faulty cables or SFPs. + + * - dev_rx_bytes + - 3 + - Total number of bytes received. + + * - dev_rx_uc_bytes + - 4 + - Unicast bytes received. + + * - dev_rx_mc_bytes + - 5 + - Multicast bytes received. + + * - dev_rx_bc_bytes + - 6 + - Broadcast bytes received. + + * - dev_rx_pkts + - 7 + - Total number of packets received. + + * - dev_rx_mc_pkts + - 8 + - Multicast packets received. + + * - dev_rx_bc_pkts + - 9 + - Broadcast packets received. + + * - dev_tx_discards + - 10 + - A packet can be discarded in the TX direction if the MAC is + being flow controlled and the NIC runs out of TX queue space. + + * - dev_tx_errors + - 11 + - A packet can be counted as TX error (and dropped) for one for the + following reasons: + + * The packet is an LSO segment, but the Layer 3 or Layer 4 offset + could not be determined. Therefore LSO could not continue. + * An invalid packet descriptor was received over PCIe. + * The packet Layer 3 length exceeds the device MTU. + * An error on the MAC/physical layer. Usually due to faulty cables or + SFPs. + * A CTM buffer could not be allocated. + * The packet offset was incorrect and could not be fixed by the NIC. + + * - dev_tx_bytes + - 12 + - Total number of bytes transmitted. + + * - dev_tx_uc_bytes + - 13 + - Unicast bytes transmitted. + + * - dev_tx_mc_bytes + - 14 + - Multicast bytes transmitted. + + * - dev_tx_bc_bytes + - 15 + - Broadcast bytes transmitted. + + * - dev_tx_pkts + - 16 + - Total number of packets transmitted. + + * - dev_tx_mc_pkts + - 17 + - Multicast packets transmitted. + + * - dev_tx_bc_pkts + - 18 + - Broadcast packets transmitted. + +Note that statistics unknown to the driver will be displayed as +``dev_unknown_stat$ID``, where ``$ID`` refers to the second column +above. diff --git a/Documentation/networking/device_drivers/ethernet/pensando/ionic.rst b/Documentation/networking/device_drivers/ethernet/pensando/ionic.rst new file mode 100644 index 0000000000..6ec7d686ef --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/pensando/ionic.rst @@ -0,0 +1,274 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +======================================================== +Linux Driver for the Pensando(R) Ethernet adapter family +======================================================== + +Pensando Linux Ethernet driver. +Copyright(c) 2019 Pensando Systems, Inc + +Contents +======== + +- Identifying the Adapter +- Enabling the driver +- Configuring the driver +- Statistics +- Support + +Identifying the Adapter +======================= + +To find if one or more Pensando PCI Ethernet devices are installed on the +host, check for the PCI devices:: + + $ lspci -d 1dd8: + b5:00.0 Ethernet controller: Device 1dd8:1002 + b6:00.0 Ethernet controller: Device 1dd8:1002 + +If such devices are listed as above, then the ionic.ko driver should find +and configure them for use. There should be log entries in the kernel +messages such as these:: + + $ dmesg | grep ionic + ionic 0000:b5:00.0: 126.016 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x16 link) + ionic 0000:b5:00.0 enp181s0: renamed from eth0 + ionic 0000:b5:00.0 enp181s0: Link up - 100 Gbps + ionic 0000:b6:00.0: 126.016 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x16 link) + ionic 0000:b6:00.0 enp182s0: renamed from eth0 + ionic 0000:b6:00.0 enp182s0: Link up - 100 Gbps + +Driver and firmware version information can be gathered with either of +ethtool or devlink tools:: + + $ ethtool -i enp181s0 + driver: ionic + version: 5.7.0 + firmware-version: 1.8.0-28 + ... + + $ devlink dev info pci/0000:b5:00.0 + pci/0000:b5:00.0: + driver ionic + serial_number FLM18420073 + versions: + fixed: + asic.id 0x0 + asic.rev 0x0 + running: + fw 1.8.0-28 + +See Documentation/networking/devlink/ionic.rst for more information +on the devlink dev info data. + +Enabling the driver +=================== + +The driver is enabled via the standard kernel configuration system, +using the make command:: + + make oldconfig/menuconfig/etc. + +The driver is located in the menu structure at: + + -> Device Drivers + -> Network device support (NETDEVICES [=y]) + -> Ethernet driver support + -> Pensando devices + -> Pensando Ethernet IONIC Support + +Configuring the Driver +====================== + +MTU +--- + +Jumbo frame support is available with a maximum size of 9194 bytes. + +Interrupt coalescing +-------------------- + +Interrupt coalescing can be configured by changing the rx-usecs value with +the "ethtool -C" command. The rx-usecs range is 0-190. The tx-usecs value +reflects the rx-usecs value as they are tied together on the same interrupt. + +SR-IOV +------ + +Minimal SR-IOV support is currently offered and can be enabled by setting +the sysfs 'sriov_numvfs' value, if supported by your particular firmware +configuration. + +Statistics +========== + +Basic hardware stats +-------------------- + +The commands ``netstat -i``, ``ip -s link show``, and ``ifconfig`` show +a limited set of statistics taken directly from firmware. For example:: + + $ ip -s link show enp181s0 + 7: enp181s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000 + link/ether 00:ae:cd:00:07:68 brd ff:ff:ff:ff:ff:ff + RX: bytes packets errors dropped overrun mcast + 414 5 0 0 0 0 + TX: bytes packets errors dropped carrier collsns + 1384 18 0 0 0 0 + +ethtool -S +---------- + +The statistics shown from the ``ethtool -S`` command includes a combination of +driver counters and firmware counters, including port and queue specific values. +The driver values are counters computed by the driver, and the firmware values +are gathered by the firmware from the port hardware and passed through the +driver with no further interpretation. + +Driver port specific:: + + tx_packets: 12 + tx_bytes: 964 + rx_packets: 5 + rx_bytes: 414 + tx_tso: 0 + tx_tso_bytes: 0 + tx_csum_none: 12 + tx_csum: 0 + rx_csum_none: 0 + rx_csum_complete: 3 + rx_csum_error: 0 + +Driver queue specific:: + + tx_0_pkts: 3 + tx_0_bytes: 294 + tx_0_clean: 3 + tx_0_dma_map_err: 0 + tx_0_linearize: 0 + tx_0_frags: 0 + tx_0_tso: 0 + tx_0_tso_bytes: 0 + tx_0_csum_none: 3 + tx_0_csum: 0 + tx_0_vlan_inserted: 0 + rx_0_pkts: 2 + rx_0_bytes: 120 + rx_0_dma_map_err: 0 + rx_0_alloc_err: 0 + rx_0_csum_none: 0 + rx_0_csum_complete: 0 + rx_0_csum_error: 0 + rx_0_dropped: 0 + rx_0_vlan_stripped: 0 + +Firmware port specific:: + + hw_tx_dropped: 0 + hw_rx_dropped: 0 + hw_rx_over_errors: 0 + hw_rx_missed_errors: 0 + hw_tx_aborted_errors: 0 + frames_rx_ok: 15 + frames_rx_all: 15 + frames_rx_bad_fcs: 0 + frames_rx_bad_all: 0 + octets_rx_ok: 1290 + octets_rx_all: 1290 + frames_rx_unicast: 10 + frames_rx_multicast: 5 + frames_rx_broadcast: 0 + frames_rx_pause: 0 + frames_rx_bad_length: 0 + frames_rx_undersized: 0 + frames_rx_oversized: 0 + frames_rx_fragments: 0 + frames_rx_jabber: 0 + frames_rx_pripause: 0 + frames_rx_stomped_crc: 0 + frames_rx_too_long: 0 + frames_rx_vlan_good: 3 + frames_rx_dropped: 0 + frames_rx_less_than_64b: 0 + frames_rx_64b: 4 + frames_rx_65b_127b: 11 + frames_rx_128b_255b: 0 + frames_rx_256b_511b: 0 + frames_rx_512b_1023b: 0 + frames_rx_1024b_1518b: 0 + frames_rx_1519b_2047b: 0 + frames_rx_2048b_4095b: 0 + frames_rx_4096b_8191b: 0 + frames_rx_8192b_9215b: 0 + frames_rx_other: 0 + frames_tx_ok: 31 + frames_tx_all: 31 + frames_tx_bad: 0 + octets_tx_ok: 2614 + octets_tx_total: 2614 + frames_tx_unicast: 8 + frames_tx_multicast: 21 + frames_tx_broadcast: 2 + frames_tx_pause: 0 + frames_tx_pripause: 0 + frames_tx_vlan: 0 + frames_tx_less_than_64b: 0 + frames_tx_64b: 4 + frames_tx_65b_127b: 27 + frames_tx_128b_255b: 0 + frames_tx_256b_511b: 0 + frames_tx_512b_1023b: 0 + frames_tx_1024b_1518b: 0 + frames_tx_1519b_2047b: 0 + frames_tx_2048b_4095b: 0 + frames_tx_4096b_8191b: 0 + frames_tx_8192b_9215b: 0 + frames_tx_other: 0 + frames_tx_pri_0: 0 + frames_tx_pri_1: 0 + frames_tx_pri_2: 0 + frames_tx_pri_3: 0 + frames_tx_pri_4: 0 + frames_tx_pri_5: 0 + frames_tx_pri_6: 0 + frames_tx_pri_7: 0 + frames_rx_pri_0: 0 + frames_rx_pri_1: 0 + frames_rx_pri_2: 0 + frames_rx_pri_3: 0 + frames_rx_pri_4: 0 + frames_rx_pri_5: 0 + frames_rx_pri_6: 0 + frames_rx_pri_7: 0 + tx_pripause_0_1us_count: 0 + tx_pripause_1_1us_count: 0 + tx_pripause_2_1us_count: 0 + tx_pripause_3_1us_count: 0 + tx_pripause_4_1us_count: 0 + tx_pripause_5_1us_count: 0 + tx_pripause_6_1us_count: 0 + tx_pripause_7_1us_count: 0 + rx_pripause_0_1us_count: 0 + rx_pripause_1_1us_count: 0 + rx_pripause_2_1us_count: 0 + rx_pripause_3_1us_count: 0 + rx_pripause_4_1us_count: 0 + rx_pripause_5_1us_count: 0 + rx_pripause_6_1us_count: 0 + rx_pripause_7_1us_count: 0 + rx_pause_1us_count: 0 + frames_tx_truncated: 0 + + +Support +======= + +For general Linux networking support, please use the netdev mailing +list, which is monitored by Pensando personnel:: + + netdev@vger.kernel.org + +For more specific support needs, please use the Pensando driver support +email:: + + drivers@pensando.io diff --git a/Documentation/networking/device_drivers/ethernet/smsc/smc9.rst b/Documentation/networking/device_drivers/ethernet/smsc/smc9.rst new file mode 100644 index 0000000000..e5eac896a6 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/smsc/smc9.rst @@ -0,0 +1,48 @@ +.. SPDX-License-Identifier: GPL-2.0 + +================ +SMC 9xxxx Driver +================ + +Revision 0.12 + +3/5/96 + +Copyright 1996 Erik Stahlman + +Released under terms of the GNU General Public License. + +This file contains the instructions and caveats for my SMC9xxx driver. You +should not be using the driver without reading this file. + +Things to note about installation: + + 1. The driver should work on all kernels from 1.2.13 until 1.3.71. + (A kernel patch is supplied for 1.3.71 ) + + 2. If you include this into the kernel, you might need to change some + options, such as for forcing IRQ. + + + 3. To compile as a module, run 'make'. + Make will give you the appropriate options for various kernel support. + + 4. Loading the driver as a module:: + + use: insmod smc9194.o + optional parameters: + io=xxxx : your base address + irq=xx : your irq + ifport=x : 0 for whatever is default + 1 for twisted pair + 2 for AUI ( or BNC on some cards ) + +How to obtain the latest version? + +FTP: + ftp://fenris.campus.vt.edu/smc9/smc9-12.tar.gz + ftp://sfbox.vt.edu/filebox/F/fenris/smc9/smc9-12.tar.gz + + +Contacting me: + erik@mail.vt.edu diff --git a/Documentation/networking/device_drivers/ethernet/stmicro/stmmac.rst b/Documentation/networking/device_drivers/ethernet/stmicro/stmmac.rst new file mode 100644 index 0000000000..5d46e50361 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/stmicro/stmmac.rst @@ -0,0 +1,700 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +============================================================== +Linux Driver for the Synopsys(R) Ethernet Controllers "stmmac" +============================================================== + +Authors: Giuseppe Cavallaro <peppe.cavallaro@st.com>, +Alexandre Torgue <alexandre.torgue@st.com>, Jose Abreu <joabreu@synopsys.com> + +Contents +======== + +- In This Release +- Feature List +- Kernel Configuration +- Command Line Parameters +- Driver Information and Notes +- Debug Information +- Support + +In This Release +=============== + +This file describes the stmmac Linux Driver for all the Synopsys(R) Ethernet +Controllers. + +Currently, this network device driver is for all STi embedded MAC/GMAC +(i.e. 7xxx/5xxx SoCs), SPEAr (arm), Loongson1B (mips) and XILINX XC2V3000 +FF1152AMT0221 D1215994A VIRTEX FPGA board. The Synopsys Ethernet QoS 5.0 IPK +is also supported. + +DesignWare(R) Cores Ethernet MAC 10/100/1000 Universal version 3.70a +(and older) and DesignWare(R) Cores Ethernet Quality-of-Service version 4.0 +(and upper) have been used for developing this driver as well as +DesignWare(R) Cores XGMAC - 10G Ethernet MAC and DesignWare(R) Cores +Enterprise MAC - 100G Ethernet MAC. + +This driver supports both the platform bus and PCI. + +This driver includes support for the following Synopsys(R) DesignWare(R) +Cores Ethernet Controllers and corresponding minimum and maximum versions: + ++-------------------------------+--------------+--------------+--------------+ +| Controller Name | Min. Version | Max. Version | Abbrev. Name | ++===============================+==============+==============+==============+ +| Ethernet MAC Universal | N/A | 3.73a | GMAC | ++-------------------------------+--------------+--------------+--------------+ +| Ethernet Quality-of-Service | 4.00a | N/A | GMAC4+ | ++-------------------------------+--------------+--------------+--------------+ +| XGMAC - 10G Ethernet MAC | 2.10a | N/A | XGMAC2+ | ++-------------------------------+--------------+--------------+--------------+ +| XLGMAC - 100G Ethernet MAC | 2.00a | N/A | XLGMAC2+ | ++-------------------------------+--------------+--------------+--------------+ + +For questions related to hardware requirements, refer to the documentation +supplied with your Ethernet adapter. All hardware requirements listed apply +to use with Linux. + +Feature List +============ + +The following features are available in this driver: + - GMII/MII/RGMII/SGMII/RMII/XGMII/XLGMII Interface + - Half-Duplex / Full-Duplex Operation + - Energy Efficient Ethernet (EEE) + - IEEE 802.3x PAUSE Packets (Flow Control) + - RMON/MIB Counters + - IEEE 1588 Timestamping (PTP) + - Pulse-Per-Second Output (PPS) + - MDIO Clause 22 / Clause 45 Interface + - MAC Loopback + - ARP Offloading + - Automatic CRC / PAD Insertion and Checking + - Checksum Offload for Received and Transmitted Packets + - Standard or Jumbo Ethernet Packets + - Source Address Insertion / Replacement + - VLAN TAG Insertion / Replacement / Deletion / Filtering (HASH and PERFECT) + - Programmable TX and RX Watchdog and Coalesce Settings + - Destination Address Filtering (PERFECT) + - HASH Filtering (Multicast) + - Layer 3 / Layer 4 Filtering + - Remote Wake-Up Detection + - Receive Side Scaling (RSS) + - Frame Preemption for TX and RX + - Programmable Burst Length, Threshold, Queue Size + - Multiple Queues (up to 8) + - Multiple Scheduling Algorithms (TX: WRR, DWRR, WFQ, SP, CBS, EST, TBS; + RX: WRR, SP) + - Flexible RX Parser + - TCP / UDP Segmentation Offload (TSO, USO) + - Split Header (SPH) + - Safety Features (ECC Protection, Data Parity Protection) + - Selftests using Ethtool + +Kernel Configuration +==================== + +The kernel configuration option is ``CONFIG_STMMAC_ETH``: + - ``CONFIG_STMMAC_PLATFORM``: is to enable the platform driver. + - ``CONFIG_STMMAC_PCI``: is to enable the pci driver. + +Command Line Parameters +======================= + +If the driver is built as a module the following optional parameters are used +by entering them on the command line with the modprobe command using this +syntax (e.g. for PCI module):: + + modprobe stmmac_pci [<option>=<VAL1>,<VAL2>,...] + +Driver parameters can be also passed in command line by using:: + + stmmaceth=watchdog:100,chain_mode=1 + +The default value for each parameter is generally the recommended setting, +unless otherwise noted. + +watchdog +-------- +:Valid Range: 5000-None +:Default Value: 5000 + +This parameter overrides the transmit timeout in milliseconds. + +debug +----- +:Valid Range: 0-16 (0=none,...,16=all) +:Default Value: 0 + +This parameter adjusts the level of debug messages displayed in the system +logs. + +phyaddr +------- +:Valid Range: 0-31 +:Default Value: -1 + +This parameter overrides the physical address of the PHY device. + +flow_ctrl +--------- +:Valid Range: 0-3 (0=off,1=rx,2=tx,3=rx/tx) +:Default Value: 3 + +This parameter changes the default Flow Control ability. + +pause +----- +:Valid Range: 0-65535 +:Default Value: 65535 + +This parameter changes the default Flow Control Pause time. + +tc +-- +:Valid Range: 64-256 +:Default Value: 64 + +This parameter changes the default HW FIFO Threshold control value. + +buf_sz +------ +:Valid Range: 1536-16384 +:Default Value: 1536 + +This parameter changes the default RX DMA packet buffer size. + +eee_timer +--------- +:Valid Range: 0-None +:Default Value: 1000 + +This parameter changes the default LPI TX Expiration time in milliseconds. + +chain_mode +---------- +:Valid Range: 0-1 (0=off,1=on) +:Default Value: 0 + +This parameter changes the default mode of operation from Ring Mode to +Chain Mode. + +Driver Information and Notes +============================ + +Transmit Process +---------------- + +The xmit method is invoked when the kernel needs to transmit a packet; it sets +the descriptors in the ring and informs the DMA engine that there is a packet +ready to be transmitted. + +By default, the driver sets the ``NETIF_F_SG`` bit in the features field of +the ``net_device`` structure, enabling the scatter-gather feature. This is +true on chips and configurations where the checksum can be done in hardware. + +Once the controller has finished transmitting the packet, timer will be +scheduled to release the transmit resources. + +Receive Process +--------------- + +When one or more packets are received, an interrupt happens. The interrupts +are not queued, so the driver has to scan all the descriptors in the ring +during the receive process. + +This is based on NAPI, so the interrupt handler signals only if there is work +to be done, and it exits. Then the poll method will be scheduled at some +future point. + +The incoming packets are stored, by the DMA, in a list of pre-allocated socket +buffers in order to avoid the memcpy (zero-copy). + +Interrupt Mitigation +-------------------- + +The driver is able to mitigate the number of its DMA interrupts using NAPI for +the reception on chips older than the 3.50. New chips have an HW RX Watchdog +used for this mitigation. + +Mitigation parameters can be tuned by ethtool. + +WoL +--- + +Wake up on Lan feature through Magic and Unicast frames are supported for the +GMAC, GMAC4/5 and XGMAC core. + +DMA Descriptors +--------------- + +Driver handles both normal and alternate descriptors. The latter has been only +tested on DesignWare(R) Cores Ethernet MAC Universal version 3.41a and later. + +stmmac supports DMA descriptor to operate both in dual buffer (RING) and +linked-list(CHAINED) mode. In RING each descriptor points to two data buffer +pointers whereas in CHAINED mode they point to only one data buffer pointer. +RING mode is the default. + +In CHAINED mode each descriptor will have pointer to next descriptor in the +list, hence creating the explicit chaining in the descriptor itself, whereas +such explicit chaining is not possible in RING mode. + +Extended Descriptors +-------------------- + +The extended descriptors give us information about the Ethernet payload when +it is carrying PTP packets or TCP/UDP/ICMP over IP. These are not available on +GMAC Synopsys(R) chips older than the 3.50. At probe time the driver will +decide if these can be actually used. This support also is mandatory for PTPv2 +because the extra descriptors are used for saving the hardware timestamps and +Extended Status. + +Ethtool Support +--------------- + +Ethtool is supported. For example, driver statistics (including RMON), +internal errors can be taken using:: + + ethtool -S ethX + +Ethtool selftests are also supported. This allows to do some early sanity +checks to the HW using MAC and PHY loopback mechanisms:: + + ethtool -t ethX + +Jumbo and Segmentation Offloading +--------------------------------- + +Jumbo frames are supported and tested for the GMAC. The GSO has been also +added but it's performed in software. LRO is not supported. + +TSO Support +----------- + +TSO (TCP Segmentation Offload) feature is supported by GMAC > 4.x and XGMAC +chip family. When a packet is sent through TCP protocol, the TCP stack ensures +that the SKB provided to the low level driver (stmmac in our case) matches +with the maximum frame len (IP header + TCP header + payload <= 1500 bytes +(for MTU set to 1500)). It means that if an application using TCP want to send +a packet which will have a length (after adding headers) > 1514 the packet +will be split in several TCP packets: The data payload is split and headers +(TCP/IP ..) are added. It is done by software. + +When TSO is enabled, the TCP stack doesn't care about the maximum frame length +and provide SKB packet to stmmac as it is. The GMAC IP will have to perform +the segmentation by it self to match with maximum frame length. + +This feature can be enabled in device tree through ``snps,tso`` entry. + +Energy Efficient Ethernet +------------------------- + +Energy Efficient Ethernet (EEE) enables IEEE 802.3 MAC sublayer along with a +family of Physical layer to operate in the Low Power Idle (LPI) mode. The EEE +mode supports the IEEE 802.3 MAC operation at 100Mbps, 1000Mbps and 1Gbps. + +The LPI mode allows power saving by switching off parts of the communication +device functionality when there is no data to be transmitted & received. +The system on both the side of the link can disable some functionalities and +save power during the period of low-link utilization. The MAC controls whether +the system should enter or exit the LPI mode and communicate this to PHY. + +As soon as the interface is opened, the driver verifies if the EEE can be +supported. This is done by looking at both the DMA HW capability register and +the PHY devices MCD registers. + +To enter in TX LPI mode the driver needs to have a software timer that enable +and disable the LPI mode when there is nothing to be transmitted. + +Precision Time Protocol (PTP) +----------------------------- + +The driver supports the IEEE 1588-2002, Precision Time Protocol (PTP), which +enables precise synchronization of clocks in measurement and control systems +implemented with technologies such as network communication. + +In addition to the basic timestamp features mentioned in IEEE 1588-2002 +Timestamps, new GMAC cores support the advanced timestamp features. +IEEE 1588-2008 can be enabled when configuring the Kernel. + +SGMII/RGMII Support +------------------- + +New GMAC devices provide own way to manage RGMII/SGMII. This information is +available at run-time by looking at the HW capability register. This means +that the stmmac can manage auto-negotiation and link status w/o using the +PHYLIB stuff. In fact, the HW provides a subset of extended registers to +restart the ANE, verify Full/Half duplex mode and Speed. Thanks to these +registers, it is possible to look at the Auto-negotiated Link Parter Ability. + +Physical +-------- + +The driver is compatible with Physical Abstraction Layer to be connected with +PHY and GPHY devices. + +Platform Information +-------------------- + +Several information can be passed through the platform and device-tree. + +:: + + struct plat_stmmacenet_data { + +1) Bus identifier:: + + int bus_id; + +2) PHY Physical Address. If set to -1 the driver will pick the first PHY it +finds:: + + int phy_addr; + +3) PHY Device Interface:: + + int interface; + +4) Specific platform fields for the MDIO bus:: + + struct stmmac_mdio_bus_data *mdio_bus_data; + +5) Internal DMA parameters:: + + struct stmmac_dma_cfg *dma_cfg; + +6) Fixed CSR Clock Range selection:: + + int clk_csr; + +7) HW uses the GMAC core:: + + int has_gmac; + +8) If set the MAC will use Enhanced Descriptors:: + + int enh_desc; + +9) Core is able to perform TX Checksum and/or RX Checksum in HW:: + + int tx_coe; + int rx_coe; + +11) Some HWs are not able to perform the csum in HW for over-sized frames due +to limited buffer sizes. Setting this flag the csum will be done in SW on +JUMBO frames:: + + int bugged_jumbo; + +12) Core has the embedded power module:: + + int pmt; + +13) Force DMA to use the Store and Forward mode or Threshold mode:: + + int force_sf_dma_mode; + int force_thresh_dma_mode; + +15) Force to disable the RX Watchdog feature and switch to NAPI mode:: + + int riwt_off; + +16) Limit the maximum operating speed and MTU:: + + int max_speed; + int maxmtu; + +18) Number of Multicast/Unicast filters:: + + int multicast_filter_bins; + int unicast_filter_entries; + +20) Limit the maximum TX and RX FIFO size:: + + int tx_fifo_size; + int rx_fifo_size; + +21) Use the specified number of TX and RX Queues:: + + u32 rx_queues_to_use; + u32 tx_queues_to_use; + +22) Use the specified TX and RX scheduling algorithm:: + + u8 rx_sched_algorithm; + u8 tx_sched_algorithm; + +23) Internal TX and RX Queue parameters:: + + struct stmmac_rxq_cfg rx_queues_cfg[MTL_MAX_RX_QUEUES]; + struct stmmac_txq_cfg tx_queues_cfg[MTL_MAX_TX_QUEUES]; + +24) This callback is used for modifying some syscfg registers (on ST SoCs) +according to the link speed negotiated by the physical layer:: + + void (*fix_mac_speed)(void *priv, unsigned int speed); + +25) Callbacks used for calling a custom initialization; This is sometimes +necessary on some platforms (e.g. ST boxes) where the HW needs to have set +some PIO lines or system cfg registers. init/exit callbacks should not use +or modify platform data:: + + int (*init)(struct platform_device *pdev, void *priv); + void (*exit)(struct platform_device *pdev, void *priv); + +26) Perform HW setup of the bus. For example, on some ST platforms this field +is used to configure the AMBA bridge to generate more efficient STBus traffic:: + + struct mac_device_info *(*setup)(void *priv); + void *bsp_priv; + +27) Internal clocks and rates:: + + struct clk *stmmac_clk; + struct clk *pclk; + struct clk *clk_ptp_ref; + unsigned int clk_ptp_rate; + unsigned int clk_ref_rate; + s32 ptp_max_adj; + +28) Main reset:: + + struct reset_control *stmmac_rst; + +29) AXI Internal Parameters:: + + struct stmmac_axi *axi; + +30) HW uses GMAC>4 cores:: + + int has_gmac4; + +31) HW is sun8i based:: + + bool has_sun8i; + +32) Enables TSO feature:: + + bool tso_en; + +33) Enables Receive Side Scaling (RSS) feature:: + + int rss_en; + +34) MAC Port selection:: + + int mac_port_sel_speed; + +35) Enables TX LPI Clock Gating:: + + bool en_tx_lpi_clockgating; + +36) HW uses XGMAC>2.10 cores:: + + int has_xgmac; + +:: + + } + +For MDIO bus data, we have: + +:: + + struct stmmac_mdio_bus_data { + +1) PHY mask passed when MDIO bus is registered:: + + unsigned int phy_mask; + +2) List of IRQs, one per PHY:: + + int *irqs; + +3) If IRQs is NULL, use this for probed PHY:: + + int probed_phy_irq; + +4) Set to true if PHY needs reset:: + + bool needs_reset; + +:: + + } + +For DMA engine configuration, we have: + +:: + + struct stmmac_dma_cfg { + +1) Programmable Burst Length (TX and RX):: + + int pbl; + +2) If set, DMA TX / RX will use this value rather than pbl:: + + int txpbl; + int rxpbl; + +3) Enable 8xPBL:: + + bool pblx8; + +4) Enable Fixed or Mixed burst:: + + int fixed_burst; + int mixed_burst; + +5) Enable Address Aligned Beats:: + + bool aal; + +6) Enable Enhanced Addressing (> 32 bits):: + + bool eame; + +:: + + } + +For DMA AXI parameters, we have: + +:: + + struct stmmac_axi { + +1) Enable AXI LPI:: + + bool axi_lpi_en; + bool axi_xit_frm; + +2) Set AXI Write / Read maximum outstanding requests:: + + u32 axi_wr_osr_lmt; + u32 axi_rd_osr_lmt; + +3) Set AXI 4KB bursts:: + + bool axi_kbbe; + +4) Set AXI maximum burst length map:: + + u32 axi_blen[AXI_BLEN]; + +5) Set AXI Fixed burst / mixed burst:: + + bool axi_fb; + bool axi_mb; + +6) Set AXI rebuild incrx mode:: + + bool axi_rb; + +:: + + } + +For the RX Queues configuration, we have: + +:: + + struct stmmac_rxq_cfg { + +1) Mode to use (DCB or AVB):: + + u8 mode_to_use; + +2) DMA channel to use:: + + u32 chan; + +3) Packet routing, if applicable:: + + u8 pkt_route; + +4) Use priority routing, and priority to route:: + + bool use_prio; + u32 prio; + +:: + + } + +For the TX Queues configuration, we have: + +:: + + struct stmmac_txq_cfg { + +1) Queue weight in scheduler:: + + u32 weight; + +2) Mode to use (DCB or AVB):: + + u8 mode_to_use; + +3) Credit Base Shaper Parameters:: + + u32 send_slope; + u32 idle_slope; + u32 high_credit; + u32 low_credit; + +4) Use priority scheduling, and priority:: + + bool use_prio; + u32 prio; + +:: + + } + +Device Tree Information +----------------------- + +Please refer to the following document: +Documentation/devicetree/bindings/net/snps,dwmac.yaml + +HW Capabilities +--------------- + +Note that, starting from new chips, where it is available the HW capability +register, many configurations are discovered at run-time for example to +understand if EEE, HW csum, PTP, enhanced descriptor etc are actually +available. As strategy adopted in this driver, the information from the HW +capability register can replace what has been passed from the platform. + +Debug Information +================= + +The driver exports many information i.e. internal statistics, debug +information, MAC and DMA registers etc. + +These can be read in several ways depending on the type of the information +actually needed. + +For example a user can be use the ethtool support to get statistics: e.g. +using: ``ethtool -S ethX`` (that shows the Management counters (MMC) if +supported) or sees the MAC/DMA registers: e.g. using: ``ethtool -d ethX`` + +Compiling the Kernel with ``CONFIG_DEBUG_FS`` the driver will export the +following debugfs entries: + + - ``descriptors_status``: To show the DMA TX/RX descriptor rings + - ``dma_cap``: To show the HW Capabilities + +Developer can also use the ``debug`` module parameter to get further debug +information (please see: NETIF Msg Level). + +Support +======= + +If an issue is identified with the released source code on a supported kernel +with a supported adapter, email the specific information related to the +issue to netdev@vger.kernel.org diff --git a/Documentation/networking/device_drivers/ethernet/ti/am65_nuss_cpsw_switchdev.rst b/Documentation/networking/device_drivers/ethernet/ti/am65_nuss_cpsw_switchdev.rst new file mode 100644 index 0000000000..25fd9aa284 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/ti/am65_nuss_cpsw_switchdev.rst @@ -0,0 +1,143 @@ +.. SPDX-License-Identifier: GPL-2.0 + +=================================================================== +Texas Instruments K3 AM65 CPSW NUSS switchdev based ethernet driver +=================================================================== + +:Version: 1.0 + +Port renaming +============= + +In order to rename via udev:: + + ip -d link show dev sw0p1 | grep switchid + + SUBSYSTEM=="net", ACTION=="add", ATTR{phys_switch_id}==<switchid>, \ + ATTR{phys_port_name}!="", NAME="sw0$attr{phys_port_name}" + + +Multi mac mode +============== + +- The driver is operating in multi-mac mode by default, thus + working as N individual network interfaces. + +Devlink configuration parameters +================================ + +See Documentation/networking/devlink/am65-nuss-cpsw-switch.rst + +Enabling "switch" +================= + +The Switch mode can be enabled by configuring devlink driver parameter +"switch_mode" to 1/true:: + + devlink dev param set platform/c000000.ethernet \ + name switch_mode value true cmode runtime + +This can be done regardless of the state of Port's netdev devices - UP/DOWN, but +Port's netdev devices have to be in UP before joining to the bridge to avoid +overwriting of bridge configuration as CPSW switch driver completely reloads its +configuration when first port changes its state to UP. + +When the both interfaces joined the bridge - CPSW switch driver will enable +marking packets with offload_fwd_mark flag. + +All configuration is implemented via switchdev API. + +Bridge setup +============ + +:: + + devlink dev param set platform/c000000.ethernet \ + name switch_mode value true cmode runtime + + ip link add name br0 type bridge + ip link set dev br0 type bridge ageing_time 1000 + ip link set dev sw0p1 up + ip link set dev sw0p2 up + ip link set dev sw0p1 master br0 + ip link set dev sw0p2 master br0 + + [*] bridge vlan add dev br0 vid 1 pvid untagged self + + [*] if vlan_filtering=1. where default_pvid=1 + + Note. Steps [*] are mandatory. + + +On/off STP +========== + +:: + + ip link set dev BRDEV type bridge stp_state 1/0 + +VLAN configuration +================== + +:: + + bridge vlan add dev br0 vid 1 pvid untagged self <---- add cpu port to VLAN 1 + +Note. This step is mandatory for bridge/default_pvid. + +Add extra VLANs +=============== + + 1. untagged:: + + bridge vlan add dev sw0p1 vid 100 pvid untagged master + bridge vlan add dev sw0p2 vid 100 pvid untagged master + bridge vlan add dev br0 vid 100 pvid untagged self <---- Add cpu port to VLAN100 + + 2. tagged:: + + bridge vlan add dev sw0p1 vid 100 master + bridge vlan add dev sw0p2 vid 100 master + bridge vlan add dev br0 vid 100 pvid tagged self <---- Add cpu port to VLAN100 + +FDBs +---- + +FDBs are automatically added on the appropriate switch port upon detection + +Manually adding FDBs:: + + bridge fdb add aa:bb:cc:dd:ee:ff dev sw0p1 master vlan 100 + bridge fdb add aa:bb:cc:dd:ee:fe dev sw0p2 master <---- Add on all VLANs + +MDBs +---- + +MDBs are automatically added on the appropriate switch port upon detection + +Manually adding MDBs:: + + bridge mdb add dev br0 port sw0p1 grp 239.1.1.1 permanent vid 100 + bridge mdb add dev br0 port sw0p1 grp 239.1.1.1 permanent <---- Add on all VLANs + +Multicast flooding +================== +CPU port mcast_flooding is always on + +Turning flooding on/off on switch ports: +bridge link set dev sw0p1 mcast_flood on/off + +Access and Trunk port +===================== + +:: + + bridge vlan add dev sw0p1 vid 100 pvid untagged master + bridge vlan add dev sw0p2 vid 100 master + + + bridge vlan add dev br0 vid 100 self + ip link add link br0 name br0.100 type vlan id 100 + +Note. Setting PVID on Bridge device itself works only for +default VLAN (default_pvid). diff --git a/Documentation/networking/device_drivers/ethernet/ti/cpsw.rst b/Documentation/networking/device_drivers/ethernet/ti/cpsw.rst new file mode 100644 index 0000000000..a88946bd18 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/ti/cpsw.rst @@ -0,0 +1,587 @@ +.. SPDX-License-Identifier: GPL-2.0 + +====================================== +Texas Instruments CPSW ethernet driver +====================================== + +Multiqueue & CBS & MQPRIO +========================= + + +The cpsw has 3 CBS shapers for each external ports. This document +describes MQPRIO and CBS Qdisc offload configuration for cpsw driver +based on examples. It potentially can be used in audio video bridging +(AVB) and time sensitive networking (TSN). + +The following examples were tested on AM572x EVM and BBB boards. + +Test setup +========== + +Under consideration two examples with AM572x EVM running cpsw driver +in dual_emac mode. + +Several prerequisites: + +- TX queues must be rated starting from txq0 that has highest priority +- Traffic classes are used starting from 0, that has highest priority +- CBS shapers should be used with rated queues +- The bandwidth for CBS shapers has to be set a little bit more then + potential incoming rate, thus, rate of all incoming tx queues has + to be a little less +- Real rates can differ, due to discreetness +- Map skb-priority to txq is not enough, also skb-priority to l2 prio + map has to be created with ip or vconfig tool +- Any l2/socket prio (0 - 7) for classes can be used, but for + simplicity default values are used: 3 and 2 +- only 2 classes tested: A and B, but checked and can work with more, + maximum allowed 4, but only for 3 rate can be set. + +Test setup for examples +======================= + +:: + + +-------------------------------+ + |--+ | + | | Workstation0 | + |E | MAC 18:03:73:66:87:42 | + +-----------------------------+ +--|t | | + | | 1 | E | | |h |./tsn_listener -d \ | + | Target board: | 0 | t |--+ |0 | 18:03:73:66:87:42 -i eth0 \| + | AM572x EVM | 0 | h | | | -s 1500 | + | | 0 | 0 | |--+ | + | Only 2 classes: |Mb +---| +-------------------------------+ + | class A, class B | | + | | +---| +-------------------------------+ + | | 1 | E | |--+ | + | | 0 | t | | | Workstation1 | + | | 0 | h |--+ |E | MAC 20:cf:30:85:7d:fd | + | |Mb | 1 | +--|t | | + +-----------------------------+ |h |./tsn_listener -d \ | + |0 | 20:cf:30:85:7d:fd -i eth0 \| + | | -s 1500 | + |--+ | + +-------------------------------+ + + +Example 1: One port tx AVB configuration scheme for target board +---------------------------------------------------------------- + +(prints and scheme for AM572x evm, applicable for single port boards) + +- tc - traffic class +- txq - transmit queue +- p - priority +- f - fifo (cpsw fifo) +- S - shaper configured + +:: + + +------------------------------------------------------------------+ u + | +---------------+ +---------------+ +------+ +------+ | s + | | | | | | | | | | e + | | App 1 | | App 2 | | Apps | | Apps | | r + | | Class A | | Class B | | Rest | | Rest | | + | | Eth0 | | Eth0 | | Eth0 | | Eth1 | | s + | | VLAN100 | | VLAN100 | | | | | | | | p + | | 40 Mb/s | | 20 Mb/s | | | | | | | | a + | | SO_PRIORITY=3 | | SO_PRIORITY=2 | | | | | | | | c + | | | | | | | | | | | | | | e + | +---|-----------+ +---|-----------+ +---|--+ +---|--+ | + +-----|------------------|------------------|--------|-------------+ + +-+ +------------+ | | + | | +-----------------+ +--+ + | | | | + +---|-------|-------------|-----------------------|----------------+ + | +----+ +----+ +----+ +----+ +----+ | + | | p3 | | p2 | | p1 | | p0 | | p0 | | k + | \ / \ / \ / \ / \ / | e + | \ / \ / \ / \ / \ / | r + | \/ \/ \/ \/ \/ | n + | | | | | | e + | | | +-----+ | | l + | | | | | | + | +----+ +----+ +----+ +----+ | s + | |tc0 | |tc1 | |tc2 | |tc0 | | p + | \ / \ / \ / \ / | a + | \ / \ / \ / \ / | c + | \/ \/ \/ \/ | e + | | | +-----+ | | + | | | | | | | + | | | | | | | + | | | | | | | + | +----+ +----+ +----+ +----+ +----+ | + | |txq0| |txq1| |txq2| |txq3| |txq4| | + | \ / \ / \ / \ / \ / | + | \ / \ / \ / \ / \ / | + | \/ \/ \/ \/ \/ | + | +-|------|------|------|--+ +--|--------------+ | + | | | | | | | Eth0.100 | | Eth1 | | + +---|------|------|------|------------------------|----------------+ + | | | | | + p p p p | + 3 2 0-1, 4-7 <- L2 priority | + | | | | | + | | | | | + +---|------|------|------|------------------------|----------------+ + | | | | | |----------+ | + | +----+ +----+ +----+ +----+ +----+ | + | |dma7| |dma6| |dma5| |dma4| |dma3| | + | \ / \ / \ / \ / \ / | c + | \S / \S / \ / \ / \ / | p + | \/ \/ \/ \/ \/ | s + | | | | +----- | | w + | | | | | | | + | | | | | | | d + | +----+ +----+ +----+p p+----+ | r + | | | | | | |o o| | | i + | | f3 | | f2 | | f0 |r r| f0 | | v + | |tc0 | |tc1 | |tc2 |t t|tc0 | | e + | \CBS / \CBS / \CBS /1 2\CBS / | r + | \S / \S / \ / \ / | + | \/ \/ \/ \/ | + +------------------------------------------------------------------+ + + +1) :: + + + // Add 4 tx queues, for interface Eth0, and 1 tx queue for Eth1 + $ ethtool -L eth0 rx 1 tx 5 + rx unmodified, ignoring + +2) :: + + // Check if num of queues is set correctly: + $ ethtool -l eth0 + Channel parameters for eth0: + Pre-set maximums: + RX: 8 + TX: 8 + Other: 0 + Combined: 0 + Current hardware settings: + RX: 1 + TX: 5 + Other: 0 + Combined: 0 + +3) :: + + // TX queues must be rated starting from 0, so set bws for tx0 and tx1 + // Set rates 40 and 20 Mb/s appropriately. + // Pay attention, real speed can differ a bit due to discreetness. + // Leave last 2 tx queues not rated. + $ echo 40 > /sys/class/net/eth0/queues/tx-0/tx_maxrate + $ echo 20 > /sys/class/net/eth0/queues/tx-1/tx_maxrate + +4) :: + + // Check maximum rate of tx (cpdma) queues: + $ cat /sys/class/net/eth0/queues/tx-*/tx_maxrate + 40 + 20 + 0 + 0 + 0 + +5) :: + + // Map skb->priority to traffic class: + // 3pri -> tc0, 2pri -> tc1, (0,1,4-7)pri -> tc2 + // Map traffic class to transmit queue: + // tc0 -> txq0, tc1 -> txq1, tc2 -> (txq2, txq3) + $ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \ + map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1 + +5a) :: + + // As two interface sharing same set of tx queues, assign all traffic + // coming to interface Eth1 to separate queue in order to not mix it + // with traffic from interface Eth0, so use separate txq to send + // packets to Eth1, so all prio -> tc0 and tc0 -> txq4 + // Here hw 0, so here still default configuration for eth1 in hw + $ tc qdisc replace dev eth1 handle 100: parent root mqprio num_tc 1 \ + map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 queues 1@4 hw 0 + +6) :: + + // Check classes settings + $ tc -g class show dev eth0 + +---(100:ffe2) mqprio + | +---(100:3) mqprio + | +---(100:4) mqprio + | + +---(100:ffe1) mqprio + | +---(100:2) mqprio + | + +---(100:ffe0) mqprio + +---(100:1) mqprio + + $ tc -g class show dev eth1 + +---(100:ffe0) mqprio + +---(100:5) mqprio + +7) :: + + // Set rate for class A - 41 Mbit (tc0, txq0) using CBS Qdisc + // Set it +1 Mb for reserve (important!) + // here only idle slope is important, others arg are ignored + // Pay attention, real speed can differ a bit due to discreetness + $ tc qdisc add dev eth0 parent 100:1 cbs locredit -1438 \ + hicredit 62 sendslope -959000 idleslope 41000 offload 1 + net eth0: set FIFO3 bw = 50 + +8) :: + + // Set rate for class B - 21 Mbit (tc1, txq1) using CBS Qdisc: + // Set it +1 Mb for reserve (important!) + $ tc qdisc add dev eth0 parent 100:2 cbs locredit -1468 \ + hicredit 65 sendslope -979000 idleslope 21000 offload 1 + net eth0: set FIFO2 bw = 30 + +9) :: + + // Create vlan 100 to map sk->priority to vlan qos + $ ip link add link eth0 name eth0.100 type vlan id 100 + 8021q: 802.1Q VLAN Support v1.8 + 8021q: adding VLAN 0 to HW filter on device eth0 + 8021q: adding VLAN 0 to HW filter on device eth1 + net eth0: Adding vlanid 100 to vlan filter + +10) :: + + // Map skb->priority to L2 prio, 1 to 1 + $ ip link set eth0.100 type vlan \ + egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 + +11) :: + + // Check egress map for vlan 100 + $ cat /proc/net/vlan/eth0.100 + [...] + INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 + EGRESS priority mappings: 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 + +12) :: + + // Run your appropriate tools with socket option "SO_PRIORITY" + // to 3 for class A and/or to 2 for class B + // (I took at https://www.spinics.net/lists/netdev/msg460869.html) + ./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p3 -s 1500& + ./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p2 -s 1500& + +13) :: + + // run your listener on workstation (should be in same vlan) + // (I took at https://www.spinics.net/lists/netdev/msg460869.html) + ./tsn_listener -d 18:03:73:66:87:42 -i enp5s0 -s 1500 + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39000 kbps + +14) :: + + // Restore default configuration if needed + $ ip link del eth0.100 + $ tc qdisc del dev eth1 root + $ tc qdisc del dev eth0 root + net eth0: Prev FIFO2 is shaped + net eth0: set FIFO3 bw = 0 + net eth0: set FIFO2 bw = 0 + $ ethtool -L eth0 rx 1 tx 1 + +Example 2: Two port tx AVB configuration scheme for target board +---------------------------------------------------------------- + +(prints and scheme for AM572x evm, for dual emac boards only) + +:: + + +------------------------------------------------------------------+ u + | +----------+ +----------+ +------+ +----------+ +----------+ | s + | | | | | | | | | | | | e + | | App 1 | | App 2 | | Apps | | App 3 | | App 4 | | r + | | Class A | | Class B | | Rest | | Class B | | Class A | | + | | Eth0 | | Eth0 | | | | | Eth1 | | Eth1 | | s + | | VLAN100 | | VLAN100 | | | | | VLAN100 | | VLAN100 | | p + | | 40 Mb/s | | 20 Mb/s | | | | | 10 Mb/s | | 30 Mb/s | | a + | | SO_PRI=3 | | SO_PRI=2 | | | | | SO_PRI=3 | | SO_PRI=2 | | c + | | | | | | | | | | | | | | | | | e + | +---|------+ +---|------+ +---|--+ +---|------+ +---|------+ | + +-----|-------------|-------------|---------|-------------|--------+ + +-+ +-------+ | +----------+ +----+ + | | +-------+------+ | | + | | | | | | + +---|-------|-------------|--------------|-------------|-------|---+ + | +----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+ | + | | p3 | | p2 | | p1 | | p0 | | p0 | | p1 | | p2 | | p3 | | k + | \ / \ / \ / \ / \ / \ / \ / \ / | e + | \ / \ / \ / \ / \ / \ / \ / \ / | r + | \/ \/ \/ \/ \/ \/ \/ \/ | n + | | | | | | | | e + | | | +----+ +----+ | | | l + | | | | | | | | + | +----+ +----+ +----+ +----+ +----+ +----+ | s + | |tc0 | |tc1 | |tc2 | |tc2 | |tc1 | |tc0 | | p + | \ / \ / \ / \ / \ / \ / | a + | \ / \ / \ / \ / \ / \ / | c + | \/ \/ \/ \/ \/ \/ | e + | | | +-----+ +-----+ | | | + | | | | | | | | | | + | | | | | | | | | | + | | | | | E E | | | | | + | +----+ +----+ +----+ +----+ t t +----+ +----+ +----+ +----+ | + | |txq0| |txq1| |txq4| |txq5| h h |txq6| |txq7| |txq3| |txq2| | + | \ / \ / \ / \ / 0 1 \ / \ / \ / \ / | + | \ / \ / \ / \ / . . \ / \ / \ / \ / | + | \/ \/ \/ \/ 1 1 \/ \/ \/ \/ | + | +-|------|------|------|--+ 0 0 +-|------|------|------|--+ | + | | | | | | | 0 0 | | | | | | | + +---|------|------|------|---------------|------|------|------|----+ + | | | | | | | | + p p p p p p p p + 3 2 0-1, 4-7 <-L2 pri-> 0-1, 4-7 2 3 + | | | | | | | | + | | | | | | | | + +---|------|------|------|---------------|------|------|------|----+ + | | | | | | | | | | + | +----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+ | + | |dma7| |dma6| |dma3| |dma2| |dma1| |dma0| |dma4| |dma5| | + | \ / \ / \ / \ / \ / \ / \ / \ / | c + | \S / \S / \ / \ / \ / \ / \S / \S / | p + | \/ \/ \/ \/ \/ \/ \/ \/ | s + | | | | +----- | | | | | w + | | | | | +----+ | | | | + | | | | | | | | | | d + | +----+ +----+ +----+p p+----+ +----+ +----+ | r + | | | | | | |o o| | | | | | | i + | | f3 | | f2 | | f0 |r CPSW r| f3 | | f2 | | f0 | | v + | |tc0 | |tc1 | |tc2 |t t|tc0 | |tc1 | |tc2 | | e + | \CBS / \CBS / \CBS /1 2\CBS / \CBS / \CBS / | r + | \S / \S / \ / \S / \S / \ / | + | \/ \/ \/ \/ \/ \/ | + +------------------------------------------------------------------+ + ========================================Eth==========================> + +1) :: + + // Add 8 tx queues, for interface Eth0, but they are common, so are accessed + // by two interfaces Eth0 and Eth1. + $ ethtool -L eth1 rx 1 tx 8 + rx unmodified, ignoring + +2) :: + + // Check if num of queues is set correctly: + $ ethtool -l eth0 + Channel parameters for eth0: + Pre-set maximums: + RX: 8 + TX: 8 + Other: 0 + Combined: 0 + Current hardware settings: + RX: 1 + TX: 8 + Other: 0 + Combined: 0 + +3) :: + + // TX queues must be rated starting from 0, so set bws for tx0 and tx1 for Eth0 + // and for tx2 and tx3 for Eth1. That is, rates 40 and 20 Mb/s appropriately + // for Eth0 and 30 and 10 Mb/s for Eth1. + // Real speed can differ a bit due to discreetness + // Leave last 4 tx queues as not rated + $ echo 40 > /sys/class/net/eth0/queues/tx-0/tx_maxrate + $ echo 20 > /sys/class/net/eth0/queues/tx-1/tx_maxrate + $ echo 30 > /sys/class/net/eth1/queues/tx-2/tx_maxrate + $ echo 10 > /sys/class/net/eth1/queues/tx-3/tx_maxrate + +4) :: + + // Check maximum rate of tx (cpdma) queues: + $ cat /sys/class/net/eth0/queues/tx-*/tx_maxrate + 40 + 20 + 30 + 10 + 0 + 0 + 0 + 0 + +5) :: + + // Map skb->priority to traffic class for Eth0: + // 3pri -> tc0, 2pri -> tc1, (0,1,4-7)pri -> tc2 + // Map traffic class to transmit queue: + // tc0 -> txq0, tc1 -> txq1, tc2 -> (txq4, txq5) + $ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \ + map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@4 hw 1 + +6) :: + + // Check classes settings + $ tc -g class show dev eth0 + +---(100:ffe2) mqprio + | +---(100:5) mqprio + | +---(100:6) mqprio + | + +---(100:ffe1) mqprio + | +---(100:2) mqprio + | + +---(100:ffe0) mqprio + +---(100:1) mqprio + +7) :: + + // Set rate for class A - 41 Mbit (tc0, txq0) using CBS Qdisc for Eth0 + // here only idle slope is important, others ignored + // Real speed can differ a bit due to discreetness + $ tc qdisc add dev eth0 parent 100:1 cbs locredit -1470 \ + hicredit 62 sendslope -959000 idleslope 41000 offload 1 + net eth0: set FIFO3 bw = 50 + +8) :: + + // Set rate for class B - 21 Mbit (tc1, txq1) using CBS Qdisc for Eth0 + $ tc qdisc add dev eth0 parent 100:2 cbs locredit -1470 \ + hicredit 65 sendslope -979000 idleslope 21000 offload 1 + net eth0: set FIFO2 bw = 30 + +9) :: + + // Create vlan 100 to map sk->priority to vlan qos for Eth0 + $ ip link add link eth0 name eth0.100 type vlan id 100 + net eth0: Adding vlanid 100 to vlan filter + +10) :: + + // Map skb->priority to L2 prio for Eth0.100, one to one + $ ip link set eth0.100 type vlan \ + egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 + +11) :: + + // Check egress map for vlan 100 + $ cat /proc/net/vlan/eth0.100 + [...] + INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 + EGRESS priority mappings: 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 + +12) :: + + // Map skb->priority to traffic class for Eth1: + // 3pri -> tc0, 2pri -> tc1, (0,1,4-7)pri -> tc2 + // Map traffic class to transmit queue: + // tc0 -> txq2, tc1 -> txq3, tc2 -> (txq6, txq7) + $ tc qdisc replace dev eth1 handle 100: parent root mqprio num_tc 3 \ + map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@2 1@3 2@6 hw 1 + +13) :: + + // Check classes settings + $ tc -g class show dev eth1 + +---(100:ffe2) mqprio + | +---(100:7) mqprio + | +---(100:8) mqprio + | + +---(100:ffe1) mqprio + | +---(100:4) mqprio + | + +---(100:ffe0) mqprio + +---(100:3) mqprio + +14) :: + + // Set rate for class A - 31 Mbit (tc0, txq2) using CBS Qdisc for Eth1 + // here only idle slope is important, others ignored, but calculated + // for interface speed - 100Mb for eth1 port. + // Set it +1 Mb for reserve (important!) + $ tc qdisc add dev eth1 parent 100:3 cbs locredit -1035 \ + hicredit 465 sendslope -69000 idleslope 31000 offload 1 + net eth1: set FIFO3 bw = 31 + +15) :: + + // Set rate for class B - 11 Mbit (tc1, txq3) using CBS Qdisc for Eth1 + // Set it +1 Mb for reserve (important!) + $ tc qdisc add dev eth1 parent 100:4 cbs locredit -1335 \ + hicredit 405 sendslope -89000 idleslope 11000 offload 1 + net eth1: set FIFO2 bw = 11 + +16) :: + + // Create vlan 100 to map sk->priority to vlan qos for Eth1 + $ ip link add link eth1 name eth1.100 type vlan id 100 + net eth1: Adding vlanid 100 to vlan filter + +17) :: + + // Map skb->priority to L2 prio for Eth1.100, one to one + $ ip link set eth1.100 type vlan \ + egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 + +18) :: + + // Check egress map for vlan 100 + $ cat /proc/net/vlan/eth1.100 + [...] + INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 + EGRESS priority mappings: 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 + +19) :: + + // Run appropriate tools with socket option "SO_PRIORITY" to 3 + // for class A and to 2 for class B. For both interfaces + ./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p2 -s 1500& + ./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p3 -s 1500& + ./tsn_talker -d 20:cf:30:85:7d:fd -i eth1.100 -p2 -s 1500& + ./tsn_talker -d 20:cf:30:85:7d:fd -i eth1.100 -p3 -s 1500& + +20) :: + + // run your listener on workstation (should be in same vlan) + // (I took at https://www.spinics.net/lists/netdev/msg460869.html) + ./tsn_listener -d 18:03:73:66:87:42 -i enp5s0 -s 1500 + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39012 kbps + Receiving data rate: 39000 kbps + +21) :: + + // Restore default configuration if needed + $ ip link del eth1.100 + $ ip link del eth0.100 + $ tc qdisc del dev eth1 root + net eth1: Prev FIFO2 is shaped + net eth1: set FIFO3 bw = 0 + net eth1: set FIFO2 bw = 0 + $ tc qdisc del dev eth0 root + net eth0: Prev FIFO2 is shaped + net eth0: set FIFO3 bw = 0 + net eth0: set FIFO2 bw = 0 + $ ethtool -L eth0 rx 1 tx 1 diff --git a/Documentation/networking/device_drivers/ethernet/ti/cpsw_switchdev.rst b/Documentation/networking/device_drivers/ethernet/ti/cpsw_switchdev.rst new file mode 100644 index 0000000000..464dce938e --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/ti/cpsw_switchdev.rst @@ -0,0 +1,242 @@ +.. SPDX-License-Identifier: GPL-2.0 + +====================================================== +Texas Instruments CPSW switchdev based ethernet driver +====================================================== + +:Version: 2.0 + +Port renaming +============= + +On older udev versions renaming of ethX to swXpY will not be automatically +supported + +In order to rename via udev:: + + ip -d link show dev sw0p1 | grep switchid + + SUBSYSTEM=="net", ACTION=="add", ATTR{phys_switch_id}==<switchid>, \ + ATTR{phys_port_name}!="", NAME="sw0$attr{phys_port_name}" + + +Dual mac mode +============= + +- The new (cpsw_new.c) driver is operating in dual-emac mode by default, thus + working as 2 individual network interfaces. Main differences from legacy CPSW + driver are: + + - optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in + addition to ALLMULTI (current port) instead of ALE_BYPASS. + So, Ports in promiscuous mode will keep possibility of mcast and vlan + filtering, which is provides significant benefits when ports are joined + to the same bridge, but without enabling "switch" mode, or to different + bridges. + - learning disabled on ports as it make not too much sense for + segregated ports - no forwarding in HW. + - enabled basic support for devlink. + + :: + + devlink dev show + platform/48484000.switch + + devlink dev param show + platform/48484000.switch: + name switch_mode type driver-specific + values: + cmode runtime value false + name ale_bypass type driver-specific + values: + cmode runtime value false + +Devlink configuration parameters +================================ + +See Documentation/networking/devlink/ti-cpsw-switch.rst + +Bridging in dual mac mode +========================= + +The dual_mac mode requires two vids to be reserved for internal purposes, +which, by default, equal CPSW Port numbers. As result, bridge has to be +configured in vlan unaware mode or default_pvid has to be adjusted:: + + ip link add name br0 type bridge + ip link set dev br0 type bridge vlan_filtering 0 + echo 0 > /sys/class/net/br0/bridge/default_pvid + ip link set dev sw0p1 master br0 + ip link set dev sw0p2 master br0 + +or:: + + ip link add name br0 type bridge + ip link set dev br0 type bridge vlan_filtering 0 + echo 100 > /sys/class/net/br0/bridge/default_pvid + ip link set dev br0 type bridge vlan_filtering 1 + ip link set dev sw0p1 master br0 + ip link set dev sw0p2 master br0 + +Enabling "switch" +================= + +The Switch mode can be enabled by configuring devlink driver parameter +"switch_mode" to 1/true:: + + devlink dev param set platform/48484000.switch \ + name switch_mode value 1 cmode runtime + +This can be done regardless of the state of Port's netdev devices - UP/DOWN, but +Port's netdev devices have to be in UP before joining to the bridge to avoid +overwriting of bridge configuration as CPSW switch driver copletly reloads its +configuration when first Port changes its state to UP. + +When the both interfaces joined the bridge - CPSW switch driver will enable +marking packets with offload_fwd_mark flag unless "ale_bypass=0" + +All configuration is implemented via switchdev API. + +Bridge setup +============ + +:: + + devlink dev param set platform/48484000.switch \ + name switch_mode value 1 cmode runtime + + ip link add name br0 type bridge + ip link set dev br0 type bridge ageing_time 1000 + ip link set dev sw0p1 up + ip link set dev sw0p2 up + ip link set dev sw0p1 master br0 + ip link set dev sw0p2 master br0 + + [*] bridge vlan add dev br0 vid 1 pvid untagged self + + [*] if vlan_filtering=1. where default_pvid=1 + + Note. Steps [*] are mandatory. + + +On/off STP +========== + +:: + + ip link set dev BRDEV type bridge stp_state 1/0 + +VLAN configuration +================== + +:: + + bridge vlan add dev br0 vid 1 pvid untagged self <---- add cpu port to VLAN 1 + +Note. This step is mandatory for bridge/default_pvid. + +Add extra VLANs +=============== + + 1. untagged:: + + bridge vlan add dev sw0p1 vid 100 pvid untagged master + bridge vlan add dev sw0p2 vid 100 pvid untagged master + bridge vlan add dev br0 vid 100 pvid untagged self <---- Add cpu port to VLAN100 + + 2. tagged:: + + bridge vlan add dev sw0p1 vid 100 master + bridge vlan add dev sw0p2 vid 100 master + bridge vlan add dev br0 vid 100 pvid tagged self <---- Add cpu port to VLAN100 + +FDBs +---- + +FDBs are automatically added on the appropriate switch port upon detection + +Manually adding FDBs:: + + bridge fdb add aa:bb:cc:dd:ee:ff dev sw0p1 master vlan 100 + bridge fdb add aa:bb:cc:dd:ee:fe dev sw0p2 master <---- Add on all VLANs + +MDBs +---- + +MDBs are automatically added on the appropriate switch port upon detection + +Manually adding MDBs:: + + bridge mdb add dev br0 port sw0p1 grp 239.1.1.1 permanent vid 100 + bridge mdb add dev br0 port sw0p1 grp 239.1.1.1 permanent <---- Add on all VLANs + +Multicast flooding +================== +CPU port mcast_flooding is always on + +Turning flooding on/off on switch ports: +bridge link set dev sw0p1 mcast_flood on/off + +Access and Trunk port +===================== + +:: + + bridge vlan add dev sw0p1 vid 100 pvid untagged master + bridge vlan add dev sw0p2 vid 100 master + + + bridge vlan add dev br0 vid 100 self + ip link add link br0 name br0.100 type vlan id 100 + +Note. Setting PVID on Bridge device itself working only for +default VLAN (default_pvid). + +NFS +=== + +The only way for NFS to work is by chrooting to a minimal environment when +switch configuration that will affect connectivity is needed. +Assuming you are booting NFS with eth1 interface(the script is hacky and +it's just there to prove NFS is doable). + +setup.sh:: + + #!/bin/sh + mkdir proc + mount -t proc none /proc + ifconfig br0 > /dev/null + if [ $? -ne 0 ]; then + echo "Setting up bridge" + ip link add name br0 type bridge + ip link set dev br0 type bridge ageing_time 1000 + ip link set dev br0 type bridge vlan_filtering 1 + + ip link set eth1 down + ip link set eth1 name sw0p1 + ip link set dev sw0p1 up + ip link set dev sw0p2 up + ip link set dev sw0p2 master br0 + ip link set dev sw0p1 master br0 + bridge vlan add dev br0 vid 1 pvid untagged self + ifconfig sw0p1 0.0.0.0 + udhchc -i br0 + fi + umount /proc + +run_nfs.sh::: + + #!/bin/sh + mkdir /tmp/root/bin -p + mkdir /tmp/root/lib -p + + cp -r /lib/ /tmp/root/ + cp -r /bin/ /tmp/root/ + cp /sbin/ip /tmp/root/bin + cp /sbin/bridge /tmp/root/bin + cp /sbin/ifconfig /tmp/root/bin + cp /sbin/udhcpc /tmp/root/bin + cp /path/to/setup.sh /tmp/root/bin + chroot /tmp/root/ busybox sh /bin/setup.sh + + run ./run_nfs.sh diff --git a/Documentation/networking/device_drivers/ethernet/ti/tlan.rst b/Documentation/networking/device_drivers/ethernet/ti/tlan.rst new file mode 100644 index 0000000000..4fdc0907f4 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/ti/tlan.rst @@ -0,0 +1,140 @@ +.. SPDX-License-Identifier: GPL-2.0 + +===================== +TLAN driver for Linux +===================== + +:Version: 1.14a + +(C) 1997-1998 Caldera, Inc. + +(C) 1998 James Banks + +(C) 1999-2001 Torben Mathiasen <tmm@image.dk, torben.mathiasen@compaq.com> + +For driver information/updates visit http://www.compaq.com + + + + + +I. Supported Devices +==================== + + Only PCI devices will work with this driver. + + Supported: + + ========= ========= =========================================== + Vendor ID Device ID Name + ========= ========= =========================================== + 0e11 ae32 Compaq Netelligent 10/100 TX PCI UTP + 0e11 ae34 Compaq Netelligent 10 T PCI UTP + 0e11 ae35 Compaq Integrated NetFlex 3/P + 0e11 ae40 Compaq Netelligent Dual 10/100 TX PCI UTP + 0e11 ae43 Compaq Netelligent Integrated 10/100 TX UTP + 0e11 b011 Compaq Netelligent 10/100 TX Embedded UTP + 0e11 b012 Compaq Netelligent 10 T/2 PCI UTP/Coax + 0e11 b030 Compaq Netelligent 10/100 TX UTP + 0e11 f130 Compaq NetFlex 3/P + 0e11 f150 Compaq NetFlex 3/P + 108d 0012 Olicom OC-2325 + 108d 0013 Olicom OC-2183 + 108d 0014 Olicom OC-2326 + ========= ========= =========================================== + + + Caveats: + + I am not sure if 100BaseTX daughterboards (for those cards which + support such things) will work. I haven't had any solid evidence + either way. + + However, if a card supports 100BaseTx without requiring an add + on daughterboard, it should work with 100BaseTx. + + The "Netelligent 10 T/2 PCI UTP/Coax" (b012) device is untested, + but I do not expect any problems. + + +II. Driver Options +================== + + 1. You can append debug=x to the end of the insmod line to get + debug messages, where x is a bit field where the bits mean + the following: + + ==== ===================================== + 0x01 Turn on general debugging messages. + 0x02 Turn on receive debugging messages. + 0x04 Turn on transmit debugging messages. + 0x08 Turn on list debugging messages. + ==== ===================================== + + 2. You can append aui=1 to the end of the insmod line to cause + the adapter to use the AUI interface instead of the 10 Base T + interface. This is also what to do if you want to use the BNC + connector on a TLAN based device. (Setting this option on a + device that does not have an AUI/BNC connector will probably + cause it to not function correctly.) + + 3. You can set duplex=1 to force half duplex, and duplex=2 to + force full duplex. + + 4. You can set speed=10 to force 10Mbs operation, and speed=100 + to force 100Mbs operation. (I'm not sure what will happen + if a card which only supports 10Mbs is forced into 100Mbs + mode.) + + 5. You have to use speed=X duplex=Y together now. If you just + do "insmod tlan.o speed=100" the driver will do Auto-Neg. + To force a 10Mbps Half-Duplex link do "insmod tlan.o speed=10 + duplex=1". + + 6. If the driver is built into the kernel, you can use the 3rd + and 4th parameters to set aui and debug respectively. For + example:: + + ether=0,0,0x1,0x7,eth0 + + This sets aui to 0x1 and debug to 0x7, assuming eth0 is a + supported TLAN device. + + The bits in the third byte are assigned as follows: + + ==== =============== + 0x01 aui + 0x02 use half duplex + 0x04 use full duplex + 0x08 use 10BaseT + 0x10 use 100BaseTx + ==== =============== + + You also need to set both speed and duplex settings when forcing + speeds with kernel-parameters. + ether=0,0,0x12,0,eth0 will force link to 100Mbps Half-Duplex. + + 7. If you have more than one tlan adapter in your system, you can + use the above options on a per adapter basis. To force a 100Mbit/HD + link with your eth1 adapter use:: + + insmod tlan speed=0,100 duplex=0,1 + + Now eth0 will use auto-neg and eth1 will be forced to 100Mbit/HD. + Note that the tlan driver supports a maximum of 8 adapters. + + +III. Things to try if you have problems +======================================= + + 1. Make sure your card's PCI id is among those listed in + section I, above. + 2. Make sure routing is correct. + 3. Try forcing different speed/duplex settings + + +There is also a tlan mailing list which you can join by sending "subscribe tlan" +in the body of an email to majordomo@vuser.vu.union.edu. + +There is also a tlan website at http://www.compaq.com + diff --git a/Documentation/networking/device_drivers/ethernet/toshiba/spider_net.rst b/Documentation/networking/device_drivers/ethernet/toshiba/spider_net.rst new file mode 100644 index 0000000000..fe5b32be15 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/toshiba/spider_net.rst @@ -0,0 +1,202 @@ +.. SPDX-License-Identifier: GPL-2.0 + +=========================== +The Spidernet Device Driver +=========================== + +Written by Linas Vepstas <linas@austin.ibm.com> + +Version of 7 June 2007 + +Abstract +======== +This document sketches the structure of portions of the spidernet +device driver in the Linux kernel tree. The spidernet is a gigabit +ethernet device built into the Toshiba southbridge commonly used +in the SONY Playstation 3 and the IBM QS20 Cell blade. + +The Structure of the RX Ring. +============================= +The receive (RX) ring is a circular linked list of RX descriptors, +together with three pointers into the ring that are used to manage its +contents. + +The elements of the ring are called "descriptors" or "descrs"; they +describe the received data. This includes a pointer to a buffer +containing the received data, the buffer size, and various status bits. + +There are three primary states that a descriptor can be in: "empty", +"full" and "not-in-use". An "empty" or "ready" descriptor is ready +to receive data from the hardware. A "full" descriptor has data in it, +and is waiting to be emptied and processed by the OS. A "not-in-use" +descriptor is neither empty or full; it is simply not ready. It may +not even have a data buffer in it, or is otherwise unusable. + +During normal operation, on device startup, the OS (specifically, the +spidernet device driver) allocates a set of RX descriptors and RX +buffers. These are all marked "empty", ready to receive data. This +ring is handed off to the hardware, which sequentially fills in the +buffers, and marks them "full". The OS follows up, taking the full +buffers, processing them, and re-marking them empty. + +This filling and emptying is managed by three pointers, the "head" +and "tail" pointers, managed by the OS, and a hardware current +descriptor pointer (GDACTDPA). The GDACTDPA points at the descr +currently being filled. When this descr is filled, the hardware +marks it full, and advances the GDACTDPA by one. Thus, when there is +flowing RX traffic, every descr behind it should be marked "full", +and everything in front of it should be "empty". If the hardware +discovers that the current descr is not empty, it will signal an +interrupt, and halt processing. + +The tail pointer tails or trails the hardware pointer. When the +hardware is ahead, the tail pointer will be pointing at a "full" +descr. The OS will process this descr, and then mark it "not-in-use", +and advance the tail pointer. Thus, when there is flowing RX traffic, +all of the descrs in front of the tail pointer should be "full", and +all of those behind it should be "not-in-use". When RX traffic is not +flowing, then the tail pointer can catch up to the hardware pointer. +The OS will then note that the current tail is "empty", and halt +processing. + +The head pointer (somewhat mis-named) follows after the tail pointer. +When traffic is flowing, then the head pointer will be pointing at +a "not-in-use" descr. The OS will perform various housekeeping duties +on this descr. This includes allocating a new data buffer and +dma-mapping it so as to make it visible to the hardware. The OS will +then mark the descr as "empty", ready to receive data. Thus, when there +is flowing RX traffic, everything in front of the head pointer should +be "not-in-use", and everything behind it should be "empty". If no +RX traffic is flowing, then the head pointer can catch up to the tail +pointer, at which point the OS will notice that the head descr is +"empty", and it will halt processing. + +Thus, in an idle system, the GDACTDPA, tail and head pointers will +all be pointing at the same descr, which should be "empty". All of the +other descrs in the ring should be "empty" as well. + +The show_rx_chain() routine will print out the locations of the +GDACTDPA, tail and head pointers. It will also summarize the contents +of the ring, starting at the tail pointer, and listing the status +of the descrs that follow. + +A typical example of the output, for a nearly idle system, might be:: + + net eth1: Total number of descrs=256 + net eth1: Chain tail located at descr=20 + net eth1: Chain head is at 20 + net eth1: HW curr desc (GDACTDPA) is at 21 + net eth1: Have 1 descrs with stat=x40800101 + net eth1: HW next desc (GDACNEXTDA) is at 22 + net eth1: Last 255 descrs with stat=xa0800000 + +In the above, the hardware has filled in one descr, number 20. Both +head and tail are pointing at 20, because it has not yet been emptied. +Meanwhile, hw is pointing at 21, which is free. + +The "Have nnn decrs" refers to the descr starting at the tail: in this +case, nnn=1 descr, starting at descr 20. The "Last nnn descrs" refers +to all of the rest of the descrs, from the last status change. The "nnn" +is a count of how many descrs have exactly the same status. + +The status x4... corresponds to "full" and status xa... corresponds +to "empty". The actual value printed is RXCOMST_A. + +In the device driver source code, a different set of names are +used for these same concepts, so that:: + + "empty" == SPIDER_NET_DESCR_CARDOWNED == 0xa + "full" == SPIDER_NET_DESCR_FRAME_END == 0x4 + "not in use" == SPIDER_NET_DESCR_NOT_IN_USE == 0xf + + +The RX RAM full bug/feature +=========================== + +As long as the OS can empty out the RX buffers at a rate faster than +the hardware can fill them, there is no problem. If, for some reason, +the OS fails to empty the RX ring fast enough, the hardware GDACTDPA +pointer will catch up to the head, notice the not-empty condition, +ad stop. However, RX packets may still continue arriving on the wire. +The spidernet chip can save some limited number of these in local RAM. +When this local ram fills up, the spider chip will issue an interrupt +indicating this (GHIINT0STS will show ERRINT, and the GRMFLLINT bit +will be set in GHIINT1STS). When the RX ram full condition occurs, +a certain bug/feature is triggered that has to be specially handled. +This section describes the special handling for this condition. + +When the OS finally has a chance to run, it will empty out the RX ring. +In particular, it will clear the descriptor on which the hardware had +stopped. However, once the hardware has decided that a certain +descriptor is invalid, it will not restart at that descriptor; instead +it will restart at the next descr. This potentially will lead to a +deadlock condition, as the tail pointer will be pointing at this descr, +which, from the OS point of view, is empty; the OS will be waiting for +this descr to be filled. However, the hardware has skipped this descr, +and is filling the next descrs. Since the OS doesn't see this, there +is a potential deadlock, with the OS waiting for one descr to fill, +while the hardware is waiting for a different set of descrs to become +empty. + +A call to show_rx_chain() at this point indicates the nature of the +problem. A typical print when the network is hung shows the following:: + + net eth1: Spider RX RAM full, incoming packets might be discarded! + net eth1: Total number of descrs=256 + net eth1: Chain tail located at descr=255 + net eth1: Chain head is at 255 + net eth1: HW curr desc (GDACTDPA) is at 0 + net eth1: Have 1 descrs with stat=xa0800000 + net eth1: HW next desc (GDACNEXTDA) is at 1 + net eth1: Have 127 descrs with stat=x40800101 + net eth1: Have 1 descrs with stat=x40800001 + net eth1: Have 126 descrs with stat=x40800101 + net eth1: Last 1 descrs with stat=xa0800000 + +Both the tail and head pointers are pointing at descr 255, which is +marked xa... which is "empty". Thus, from the OS point of view, there +is nothing to be done. In particular, there is the implicit assumption +that everything in front of the "empty" descr must surely also be empty, +as explained in the last section. The OS is waiting for descr 255 to +become non-empty, which, in this case, will never happen. + +The HW pointer is at descr 0. This descr is marked 0x4.. or "full". +Since its already full, the hardware can do nothing more, and thus has +halted processing. Notice that descrs 0 through 254 are all marked +"full", while descr 254 and 255 are empty. (The "Last 1 descrs" is +descr 254, since tail was at 255.) Thus, the system is deadlocked, +and there can be no forward progress; the OS thinks there's nothing +to do, and the hardware has nowhere to put incoming data. + +This bug/feature is worked around with the spider_net_resync_head_ptr() +routine. When the driver receives RX interrupts, but an examination +of the RX chain seems to show it is empty, then it is probable that +the hardware has skipped a descr or two (sometimes dozens under heavy +network conditions). The spider_net_resync_head_ptr() subroutine will +search the ring for the next full descr, and the driver will resume +operations there. Since this will leave "holes" in the ring, there +is also a spider_net_resync_tail_ptr() that will skip over such holes. + +As of this writing, the spider_net_resync() strategy seems to work very +well, even under heavy network loads. + + +The TX ring +=========== +The TX ring uses a low-watermark interrupt scheme to make sure that +the TX queue is appropriately serviced for large packet sizes. + +For packet sizes greater than about 1KBytes, the kernel can fill +the TX ring quicker than the device can drain it. Once the ring +is full, the netdev is stopped. When there is room in the ring, +the netdev needs to be reawakened, so that more TX packets are placed +in the ring. The hardware can empty the ring about four times per jiffy, +so its not appropriate to wait for the poll routine to refill, since +the poll routine runs only once per jiffy. The low-watermark mechanism +marks a descr about 1/4th of the way from the bottom of the queue, so +that an interrupt is generated when the descr is processed. This +interrupt wakes up the netdev, which can then refill the queue. +For large packets, this mechanism generates a relatively small number +of interrupts, about 1K/sec. For smaller packets, this will drop to zero +interrupts, as the hardware can empty the queue faster than the kernel +can fill it. diff --git a/Documentation/networking/device_drivers/ethernet/wangxun/ngbe.rst b/Documentation/networking/device_drivers/ethernet/wangxun/ngbe.rst new file mode 100644 index 0000000000..43a02f9943 --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/wangxun/ngbe.rst @@ -0,0 +1,14 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============================================================= +Linux Base Driver for WangXun(R) Gigabit PCI Express Adapters +============================================================= + +WangXun Gigabit Linux driver. +Copyright (c) 2019 - 2022 Beijing WangXun Technology Co., Ltd. + +Support +======= + If you have problems with the software or hardware, please contact our + customer support team via email at nic-support@net-swift.com or check our website + at https://www.net-swift.com diff --git a/Documentation/networking/device_drivers/ethernet/wangxun/txgbe.rst b/Documentation/networking/device_drivers/ethernet/wangxun/txgbe.rst new file mode 100644 index 0000000000..d052ef40fe --- /dev/null +++ b/Documentation/networking/device_drivers/ethernet/wangxun/txgbe.rst @@ -0,0 +1,20 @@ +.. SPDX-License-Identifier: GPL-2.0 + +================================================================ +Linux Base Driver for WangXun(R) 10 Gigabit PCI Express Adapters +================================================================ + +WangXun 10 Gigabit Linux driver. +Copyright (c) 2015 - 2022 Beijing WangXun Technology Co., Ltd. + + +Contents +======== + +- Support + + +Support +======= +If you got any problem, contact Wangxun support team via nic-support@net-swift.com +and Cc: netdev. diff --git a/Documentation/networking/device_drivers/fddi/defza.rst b/Documentation/networking/device_drivers/fddi/defza.rst new file mode 100644 index 0000000000..7393f33ea7 --- /dev/null +++ b/Documentation/networking/device_drivers/fddi/defza.rst @@ -0,0 +1,63 @@ +.. SPDX-License-Identifier: GPL-2.0 + +===================================================== +Notes on the DEC FDDIcontroller 700 (DEFZA-xx) driver +===================================================== + +:Version: v.1.1.4 + + +DEC FDDIcontroller 700 is DEC's first-generation TURBOchannel FDDI +network card, designed in 1990 specifically for the DECstation 5000 +model 200 workstation. The board is a single attachment station and +it was manufactured in two variations, both of which are supported. + +First is the SAS MMF DEFZA-AA option, the original design implementing +the standard MMF-PMD, however with a pair of ST connectors rather than +the usual MIC connector. The other one is the SAS ThinWire/STP DEFZA-CA +option, denoted 700-C, with the network medium selectable by a switch +between the DEC proprietary ThinWire-PMD using a BNC connector and the +standard STP-PMD using a DE-9F connector. This option can interface to +a DECconcentrator 500 device and, in the case of the STP-PMD, also other +FDDI equipment and was designed to make it easier to transition from +existing IEEE 802.3 10BASE2 Ethernet and IEEE 802.5 Token Ring networks +by providing means to reuse existing cabling. + +This driver handles any number of cards installed in a single system. +They get fddi0, fddi1, etc. interface names assigned in the order of +increasing TURBOchannel slot numbers. + +The board only supports DMA on the receive side. Transmission involves +the use of PIO. As a result under a heavy transmission load there will +be a significant impact on system performance. + +The board supports a 64-entry CAM for matching destination addresses. +Two entries are preoccupied by the Directed Beacon and Ring Purger +multicast addresses and the rest is used as a multicast filter. An +all-multi mode is also supported for LLC frames and it is used if +requested explicitly or if the CAM overflows. The promiscuous mode +supports separate enables for LLC and SMT frames, but this driver +doesn't support changing them individually. + + +Known problems: + +None. + + +To do: + +5. MAC address change. The card does not support changing the Media + Access Controller's address registers but a similar effect can be + achieved by adding an alias to the CAM. There is no way to disable + matching against the original address though. + +7. Queueing incoming/outgoing SMT frames in the driver if the SMT + receive/RMC transmit ring is full. (?) + +8. Retrieving/reporting FDDI/SNMP stats. + + +Both success and failure reports are welcome. + +Maciej W. Rozycki <macro@orcam.me.uk> diff --git a/Documentation/networking/device_drivers/fddi/index.rst b/Documentation/networking/device_drivers/fddi/index.rst new file mode 100644 index 0000000000..0b75294e6c --- /dev/null +++ b/Documentation/networking/device_drivers/fddi/index.rst @@ -0,0 +1,19 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) + +Fiber Distributed Data Interface (FDDI) Device Drivers +====================================================== + +Contents: + +.. toctree:: + :maxdepth: 2 + + defza + skfp + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/fddi/skfp.rst b/Documentation/networking/device_drivers/fddi/skfp.rst new file mode 100644 index 0000000000..58f548105c --- /dev/null +++ b/Documentation/networking/device_drivers/fddi/skfp.rst @@ -0,0 +1,253 @@ +.. SPDX-License-Identifier: GPL-2.0 + +.. include:: <isonum.txt> + +======================== +SysKonnect driver - SKFP +======================== + +|copy| Copyright 1998-2000 SysKonnect, + +skfp.txt created 11-May-2000 + +Readme File for skfp.o v2.06 + + +.. This file contains + + (1) OVERVIEW + (2) SUPPORTED ADAPTERS + (3) GENERAL INFORMATION + (4) INSTALLATION + (5) INCLUSION OF THE ADAPTER IN SYSTEM START + (6) TROUBLESHOOTING + (7) FUNCTION OF THE ADAPTER LEDS + (8) HISTORY + + +1. Overview +=========== + +This README explains how to use the driver 'skfp' for Linux with your +network adapter. + +Chapter 2: Contains a list of all network adapters that are supported by +this driver. + +Chapter 3: + Gives some general information. + +Chapter 4: Describes common problems and solutions. + +Chapter 5: Shows the changed functionality of the adapter LEDs. + +Chapter 6: History of development. + + +2. Supported adapters +===================== + +The network driver 'skfp' supports the following network adapters: +SysKonnect adapters: + + - SK-5521 (SK-NET FDDI-UP) + - SK-5522 (SK-NET FDDI-UP DAS) + - SK-5541 (SK-NET FDDI-FP) + - SK-5543 (SK-NET FDDI-LP) + - SK-5544 (SK-NET FDDI-LP DAS) + - SK-5821 (SK-NET FDDI-UP64) + - SK-5822 (SK-NET FDDI-UP64 DAS) + - SK-5841 (SK-NET FDDI-FP64) + - SK-5843 (SK-NET FDDI-LP64) + - SK-5844 (SK-NET FDDI-LP64 DAS) + +Compaq adapters (not tested): + + - Netelligent 100 FDDI DAS Fibre SC + - Netelligent 100 FDDI SAS Fibre SC + - Netelligent 100 FDDI DAS UTP + - Netelligent 100 FDDI SAS UTP + - Netelligent 100 FDDI SAS Fibre MIC + + +3. General Information +====================== + +From v2.01 on, the driver is integrated in the linux kernel sources. +Therefore, the installation is the same as for any other adapter +supported by the kernel. + +Refer to the manual of your distribution about the installation +of network adapters. + +Makes my life much easier :-) + +4. Troubleshooting +================== + +If you run into problems during installation, check those items: + +Problem: + The FDDI adapter cannot be found by the driver. + +Reason: + Look in /proc/pci for the following entry: + + 'FDDI network controller: SysKonnect SK-FDDI-PCI ...' + + If this entry exists, then the FDDI adapter has been + found by the system and should be able to be used. + + If this entry does not exist or if the file '/proc/pci' + is not there, then you may have a hardware problem or PCI + support may not be enabled in your kernel. + + The adapter can be checked using the diagnostic program + which is available from the SysKonnect web site: + + www.syskonnect.de + + Some COMPAQ machines have a problem with PCI under + Linux. This is described in the 'PCI howto' document + (included in some distributions or available from the + www, e.g. at 'www.linux.org') and no workaround is available. + +Problem: + You want to use your computer as a router between + multiple IP subnetworks (using multiple adapters), but + you cannot reach computers in other subnetworks. + +Reason: + Either the router's kernel is not configured for IP + forwarding or there is a problem with the routing table + and gateway configuration in at least one of the + computers. + +If your problem is not listed here, please contact our +technical support for help. + +You can send email to: linux@syskonnect.de + +When contacting our technical support, +please ensure that the following information is available: + +- System Manufacturer and Model +- Boards in your system +- Distribution +- Kernel version + + +5. Function of the Adapter LEDs +=============================== + + The functionality of the LED's on the FDDI network adapters was + changed in SMT version v2.82. With this new SMT version, the yellow + LED works as a ring operational indicator. An active yellow LED + indicates that the ring is down. The green LED on the adapter now + works as a link indicator where an active GREEN LED indicates that + the respective port has a physical connection. + + With versions of SMT prior to v2.82 a ring up was indicated if the + yellow LED was off while the green LED(s) showed the connection + status of the adapter. During a ring down the green LED was off and + the yellow LED was on. + + All implementations indicate that a driver is not loaded if + all LEDs are off. + + +6. History +========== + +v2.06 (20000511) (In-Kernel version) + New features: + + - 64 bit support + - new pci dma interface + - in kernel 2.3.99 + +v2.05 (20000217) (In-Kernel version) + New features: + + - Changes for 2.3.45 kernel + +v2.04 (20000207) (Standalone version) + New features: + + - Added rx/tx byte counter + +v2.03 (20000111) (Standalone version) + Problems fixed: + + - Fixed printk statements from v2.02 + +v2.02 (991215) (Standalone version) + Problems fixed: + + - Removed unnecessary output + - Fixed path for "printver.sh" in makefile + +v2.01 (991122) (In-Kernel version) + New features: + + - Integration in Linux kernel sources + - Support for memory mapped I/O. + +v2.00 (991112) + New features: + + - Full source released under GPL + +v1.05 (991023) + Problems fixed: + + - Compilation with kernel version 2.2.13 failed + +v1.04 (990427) + Changes: + + - New SMT module included, changing LED functionality + + Problems fixed: + + - Synchronization on SMP machines was buggy + +v1.03 (990325) + Problems fixed: + + - Interrupt routing on SMP machines could be incorrect + +v1.02 (990310) + New features: + + - Support for kernel versions 2.2.x added + - Kernel patch instead of private duplicate of kernel functions + +v1.01 (980812) + Problems fixed: + + Connection hangup with telnet + Slow telnet connection + +v1.00 beta 01 (980507) + New features: + + None. + + Problems fixed: + + None. + + Known limitations: + + - tar archive instead of standard package format (rpm). + - FDDI statistic is empty. + - not tested with 2.1.xx kernels + - integration in kernel not tested + - not tested simultaneously with FDDI adapters from other vendors. + - only X86 processors supported. + - SBA (Synchronous Bandwidth Allocator) parameters can + not be configured. + - does not work on some COMPAQ machines. See the PCI howto + document for details about this problem. + - data corruption with kernel versions below 2.0.33. diff --git a/Documentation/networking/device_drivers/hamradio/baycom.rst b/Documentation/networking/device_drivers/hamradio/baycom.rst new file mode 100644 index 0000000000..fe2d010f0e --- /dev/null +++ b/Documentation/networking/device_drivers/hamradio/baycom.rst @@ -0,0 +1,174 @@ +.. SPDX-License-Identifier: GPL-2.0 + +=============================== +Linux Drivers for Baycom Modems +=============================== + +Thomas M. Sailer, HB9JNX/AE4WA, <sailer@ife.ee.ethz.ch> + +The drivers for the baycom modems have been split into +separate drivers as they did not share any code, and the driver +and device names have changed. + +This document describes the Linux Kernel Drivers for simple Baycom style +amateur radio modems. + +The following drivers are available: +==================================== + +baycom_ser_fdx: + This driver supports the SER12 modems either full or half duplex. + Its baud rate may be changed via the ``baud`` module parameter, + therefore it supports just about every bit bang modem on a + serial port. Its devices are called bcsf0 through bcsf3. + This is the recommended driver for SER12 type modems, + however if you have a broken UART clone that does not have working + delta status bits, you may try baycom_ser_hdx. + +baycom_ser_hdx: + This is an alternative driver for SER12 type modems. + It only supports half duplex, and only 1200 baud. Its devices + are called bcsh0 through bcsh3. Use this driver only if baycom_ser_fdx + does not work with your UART. + +baycom_par: + This driver supports the par96 and picpar modems. + Its devices are called bcp0 through bcp3. + +baycom_epp: + This driver supports the EPP modem. + Its devices are called bce0 through bce3. + This driver is work-in-progress. + +The following modems are supported: + +======= ======================================================================== +ser12 This is a very simple 1200 baud AFSK modem. The modem consists only + of a modulator/demodulator chip, usually a TI TCM3105. The computer + is responsible for regenerating the receiver bit clock, as well as + for handling the HDLC protocol. The modem connects to a serial port, + hence the name. Since the serial port is not used as an async serial + port, the kernel driver for serial ports cannot be used, and this + driver only supports standard serial hardware (8250, 16450, 16550) + +par96 This is a modem for 9600 baud FSK compatible to the G3RUH standard. + The modem does all the filtering and regenerates the receiver clock. + Data is transferred from and to the PC via a shift register. + The shift register is filled with 16 bits and an interrupt is signalled. + The PC then empties the shift register in a burst. This modem connects + to the parallel port, hence the name. The modem leaves the + implementation of the HDLC protocol and the scrambler polynomial to + the PC. + +picpar This is a redesign of the par96 modem by Henning Rech, DF9IC. The modem + is protocol compatible to par96, but uses only three low power ICs + and can therefore be fed from the parallel port and does not require + an additional power supply. Furthermore, it incorporates a carrier + detect circuitry. + +EPP This is a high-speed modem adaptor that connects to an enhanced parallel + port. + + Its target audience is users working over a high speed hub (76.8kbit/s). + +eppfpga This is a redesign of the EPP adaptor. +======= ======================================================================== + +All of the above modems only support half duplex communications. However, +the driver supports the KISS (see below) fullduplex command. It then simply +starts to send as soon as there's a packet to transmit and does not care +about DCD, i.e. it starts to send even if there's someone else on the channel. +This command is required by some implementations of the DAMA channel +access protocol. + + +The Interface of the drivers +============================ + +Unlike previous drivers, these drivers are no longer character devices, +but they are now true kernel network interfaces. Installation is therefore +simple. Once installed, four interfaces named bc{sf,sh,p,e}[0-3] are available. +sethdlc from the ax25 utilities may be used to set driver states etc. +Users of userland AX.25 stacks may use the net2kiss utility (also available +in the ax25 utilities package) to convert packets of a network interface +to a KISS stream on a pseudo tty. There's also a patch available from +me for WAMPES which allows attaching a kernel network interface directly. + + +Configuring the driver +====================== + +Every time a driver is inserted into the kernel, it has to know which +modems it should access at which ports. This can be done with the setbaycom +utility. If you are only using one modem, you can also configure the +driver from the insmod command line (or by means of an option line in +``/etc/modprobe.d/*.conf``). + +Examples:: + + modprobe baycom_ser_fdx mode="ser12*" iobase=0x3f8 irq=4 + sethdlc -i bcsf0 -p mode "ser12*" io 0x3f8 irq 4 + +Both lines configure the first port to drive a ser12 modem at the first +serial port (COM1 under DOS). The * in the mode parameter instructs the driver +to use the software DCD algorithm (see below):: + + insmod baycom_par mode="picpar" iobase=0x378 + sethdlc -i bcp0 -p mode "picpar" io 0x378 + +Both lines configure the first port to drive a picpar modem at the +first parallel port (LPT1 under DOS). (Note: picpar implies +hardware DCD, par96 implies software DCD). + +The channel access parameters can be set with sethdlc -a or kissparms. +Note that both utilities interpret the values slightly differently. + + +Hardware DCD versus Software DCD +================================ + +To avoid collisions on the air, the driver must know when the channel is +busy. This is the task of the DCD circuitry/software. The driver may either +utilise a software DCD algorithm (options=1) or use a DCD signal from +the hardware (options=0). + +======= ================================================================= +ser12 if software DCD is utilised, the radio's squelch should always be + open. It is highly recommended to use the software DCD algorithm, + as it is much faster than most hardware squelch circuitry. The + disadvantage is a slightly higher load on the system. + +par96 the software DCD algorithm for this type of modem is rather poor. + The modem simply does not provide enough information to implement + a reasonable DCD algorithm in software. Therefore, if your radio + feeds the DCD input of the PAR96 modem, the use of the hardware + DCD circuitry is recommended. + +picpar the picpar modem features a builtin DCD hardware, which is highly + recommended. +======= ================================================================= + + + +Compatibility with the rest of the Linux kernel +=============================================== + +The serial driver and the baycom serial drivers compete +for the same hardware resources. Of course only one driver can access a given +interface at a time. The serial driver grabs all interfaces it can find at +startup time. Therefore the baycom drivers subsequently won't be able to +access a serial port. You might therefore find it necessary to release +a port owned by the serial driver with 'setserial /dev/ttyS# uart none', where +# is the number of the interface. The baycom drivers do not reserve any +ports at startup, unless one is specified on the 'insmod' command line. Another +method to solve the problem is to compile all drivers as modules and +leave it to kmod to load the correct driver depending on the application. + +The parallel port drivers (baycom_par, baycom_epp) now use the parport subsystem +to arbitrate the ports between different client drivers. + +vy 73s de + +Tom Sailer, sailer@ife.ee.ethz.ch + +hb9jnx @ hb9w.ampr.org diff --git a/Documentation/networking/device_drivers/hamradio/index.rst b/Documentation/networking/device_drivers/hamradio/index.rst new file mode 100644 index 0000000000..7e73173205 --- /dev/null +++ b/Documentation/networking/device_drivers/hamradio/index.rst @@ -0,0 +1,19 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) + +Amateur Radio Device Drivers +============================ + +Contents: + +.. toctree:: + :maxdepth: 2 + + baycom + z8530drv + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/hamradio/z8530drv.rst b/Documentation/networking/device_drivers/hamradio/z8530drv.rst new file mode 100644 index 0000000000..d2942760f1 --- /dev/null +++ b/Documentation/networking/device_drivers/hamradio/z8530drv.rst @@ -0,0 +1,686 @@ +.. SPDX-License-Identifier: GPL-2.0 +.. include:: <isonum.txt> + +========================================================= +SCC.C - Linux driver for Z8530 based HDLC cards for AX.25 +========================================================= + + +This is a subset of the documentation. To use this driver you MUST have the +full package from: + +Internet: + + 1. ftp://ftp.ccac.rwth-aachen.de/pub/jr/z8530drv-utils_3.0-3.tar.gz + + 2. ftp://ftp.pspt.fi/pub/ham/linux/ax25/z8530drv-utils_3.0-3.tar.gz + +Please note that the information in this document may be hopelessly outdated. +A new version of the documentation, along with links to other important +Linux Kernel AX.25 documentation and programs, is available on +http://yaina.de/jreuter + +Copyright |copy| 1993,2000 by Joerg Reuter DL1BKE <jreuter@yaina.de> + +portions Copyright |copy| 1993 Guido ten Dolle PE1NNZ + +for the complete copyright notice see >> Copying.Z8530DRV << + +1. Initialization of the driver +=============================== + +To use the driver, 3 steps must be performed: + + 1. if compiled as module: loading the module + 2. Setup of hardware, MODEM and KISS parameters with sccinit + 3. Attach each channel to the Linux kernel AX.25 with "ifconfig" + +Unlike the versions below 2.4 this driver is a real network device +driver. If you want to run xNOS instead of our fine kernel AX.25 +use a 2.x version (available from above sites) or read the +AX.25-HOWTO on how to emulate a KISS TNC on network device drivers. + + +1.1 Loading the module +====================== + +(If you're going to compile the driver as a part of the kernel image, + skip this chapter and continue with 1.2) + +Before you can use a module, you'll have to load it with:: + + insmod scc.o + +please read 'man insmod' that comes with module-init-tools. + +You should include the insmod in one of the /etc/rc.d/rc.* files, +and don't forget to insert a call of sccinit after that. It +will read your /etc/z8530drv.conf. + +1.2. /etc/z8530drv.conf +======================= + +To setup all parameters you must run /sbin/sccinit from one +of your rc.*-files. This has to be done BEFORE you can +"ifconfig" an interface. Sccinit reads the file /etc/z8530drv.conf +and sets the hardware, MODEM and KISS parameters. A sample file is +delivered with this package. Change it to your needs. + +The file itself consists of two main sections. + +1.2.1 configuration of hardware parameters +========================================== + +The hardware setup section defines the following parameters for each +Z8530:: + + chip 1 + data_a 0x300 # data port A + ctrl_a 0x304 # control port A + data_b 0x301 # data port B + ctrl_b 0x305 # control port B + irq 5 # IRQ No. 5 + pclock 4915200 # clock + board BAYCOM # hardware type + escc no # enhanced SCC chip? (8580/85180/85280) + vector 0 # latch for interrupt vector + special no # address of special function register + option 0 # option to set via sfr + + +chip + - this is just a delimiter to make sccinit a bit simpler to + program. A parameter has no effect. + +data_a + - the address of the data port A of this Z8530 (needed) +ctrl_a + - the address of the control port A (needed) +data_b + - the address of the data port B (needed) +ctrl_b + - the address of the control port B (needed) + +irq + - the used IRQ for this chip. Different chips can use different + IRQs or the same. If they share an interrupt, it needs to be + specified within one chip-definition only. + +pclock - the clock at the PCLK pin of the Z8530 (option, 4915200 is + default), measured in Hertz + +board + - the "type" of the board: + + ======================= ======== + SCC type value + ======================= ======== + PA0HZP SCC card PA0HZP + EAGLE card EAGLE + PC100 card PC100 + PRIMUS-PC (DG9BL) card PRIMUS + BayCom (U)SCC card BAYCOM + ======================= ======== + +escc + - if you want support for ESCC chips (8580, 85180, 85280), set + this to "yes" (option, defaults to "no") + +vector + - address of the vector latch (aka "intack port") for PA0HZP + cards. There can be only one vector latch for all chips! + (option, defaults to 0) + +special + - address of the special function register on several cards. + (option, defaults to 0) + +option - The value you write into that register (option, default is 0) + +You can specify up to four chips (8 channels). If this is not enough, +just change:: + + #define MAXSCC 4 + +to a higher value. + +Example for the BAYCOM USCC: +---------------------------- + +:: + + chip 1 + data_a 0x300 # data port A + ctrl_a 0x304 # control port A + data_b 0x301 # data port B + ctrl_b 0x305 # control port B + irq 5 # IRQ No. 5 (#) + board BAYCOM # hardware type (*) + # + # SCC chip 2 + # + chip 2 + data_a 0x302 + ctrl_a 0x306 + data_b 0x303 + ctrl_b 0x307 + board BAYCOM + +An example for a PA0HZP card: +----------------------------- + +:: + + chip 1 + data_a 0x153 + data_b 0x151 + ctrl_a 0x152 + ctrl_b 0x150 + irq 9 + pclock 4915200 + board PA0HZP + vector 0x168 + escc no + # + # + # + chip 2 + data_a 0x157 + data_b 0x155 + ctrl_a 0x156 + ctrl_b 0x154 + irq 9 + pclock 4915200 + board PA0HZP + vector 0x168 + escc no + +A DRSI would should probably work with this: +-------------------------------------------- +(actually: two DRSI cards...) + +:: + + chip 1 + data_a 0x303 + data_b 0x301 + ctrl_a 0x302 + ctrl_b 0x300 + irq 7 + pclock 4915200 + board DRSI + escc no + # + # + # + chip 2 + data_a 0x313 + data_b 0x311 + ctrl_a 0x312 + ctrl_b 0x310 + irq 7 + pclock 4915200 + board DRSI + escc no + +Note that you cannot use the on-board baudrate generator off DRSI +cards. Use "mode dpll" for clock source (see below). + +This is based on information provided by Mike Bilow (and verified +by Paul Helay) + +The utility "gencfg" +-------------------- + +If you only know the parameters for the PE1CHL driver for DOS, +run gencfg. It will generate the correct port addresses (I hope). +Its parameters are exactly the same as the ones you use with +the "attach scc" command in net, except that the string "init" must +not appear. Example:: + + gencfg 2 0x150 4 2 0 1 0x168 9 4915200 + +will print a skeleton z8530drv.conf for the OptoSCC to stdout. + +:: + + gencfg 2 0x300 2 4 5 -4 0 7 4915200 0x10 + +does the same for the BAYCOM USCC card. In my opinion it is much easier +to edit scc_config.h... + + +1.2.2 channel configuration +=========================== + +The channel definition is divided into three sub sections for each +channel: + +An example for scc0:: + + # DEVICE + + device scc0 # the device for the following params + + # MODEM / BUFFERS + + speed 1200 # the default baudrate + clock dpll # clock source: + # dpll = normal half duplex operation + # external = MODEM provides own Rx/Tx clock + # divider = use full duplex divider if + # installed (1) + mode nrzi # HDLC encoding mode + # nrzi = 1k2 MODEM, G3RUH 9k6 MODEM + # nrz = DF9IC 9k6 MODEM + # + bufsize 384 # size of buffers. Note that this must include + # the AX.25 header, not only the data field! + # (optional, defaults to 384) + + # KISS (Layer 1) + + txdelay 36 # (see chapter 1.4) + persist 64 + slot 8 + tail 8 + fulldup 0 + wait 12 + min 3 + maxkey 7 + idle 3 + maxdef 120 + group 0 + txoff off + softdcd on + slip off + +The order WITHIN these sections is unimportant. The order OF these +sections IS important. The MODEM parameters are set with the first +recognized KISS parameter... + +Please note that you can initialize the board only once after boot +(or insmod). You can change all parameters but "mode" and "clock" +later with the Sccparam program or through KISS. Just to avoid +security holes... + +(1) this divider is usually mounted on the SCC-PBC (PA0HZP) or not + present at all (BayCom). It feeds back the output of the DPLL + (digital pll) as transmit clock. Using this mode without a divider + installed will normally result in keying the transceiver until + maxkey expires --- of course without sending anything (useful). + +2. Attachment of a channel by your AX.25 software +================================================= + +2.1 Kernel AX.25 +================ + +To set up an AX.25 device you can simply type:: + + ifconfig scc0 44.128.1.1 hw ax25 dl0tha-7 + +This will create a network interface with the IP number 44.128.20.107 +and the callsign "dl0tha". If you do not have any IP number (yet) you +can use any of the 44.128.0.0 network. Note that you do not need +axattach. The purpose of axattach (like slattach) is to create a KISS +network device linked to a TTY. Please read the documentation of the +ax25-utils and the AX.25-HOWTO to learn how to set the parameters of +the kernel AX.25. + +2.2 NOS, NET and TFKISS +======================= + +Since the TTY driver (aka KISS TNC emulation) is gone you need +to emulate the old behaviour. The cost of using these programs is +that you probably need to compile the kernel AX.25, regardless of whether +you actually use it or not. First setup your /etc/ax25/axports, +for example:: + + 9k6 dl0tha-9 9600 255 4 9600 baud port (scc3) + axlink dl0tha-15 38400 255 4 Link to NOS + +Now "ifconfig" the scc device:: + + ifconfig scc3 44.128.1.1 hw ax25 dl0tha-9 + +You can now axattach a pseudo-TTY:: + + axattach /dev/ptys0 axlink + +and start your NOS and attach /dev/ptys0 there. The problem is that +NOS is reachable only via digipeating through the kernel AX.25 +(disastrous on a DAMA controlled channel). To solve this problem, +configure "rxecho" to echo the incoming frames from "9k6" to "axlink" +and outgoing frames from "axlink" to "9k6" and start:: + + rxecho + +Or simply use "kissbridge" coming with z8530drv-utils:: + + ifconfig scc3 hw ax25 dl0tha-9 + kissbridge scc3 /dev/ptys0 + + +3. Adjustment and Display of parameters +======================================= + +3.1 Displaying SCC Parameters: +============================== + +Once a SCC channel has been attached, the parameter settings and +some statistic information can be shown using the param program:: + + dl1bke-u:~$ sccstat scc0 + + Parameters: + + speed : 1200 baud + txdelay : 36 + persist : 255 + slottime : 0 + txtail : 8 + fulldup : 1 + waittime : 12 + mintime : 3 sec + maxkeyup : 7 sec + idletime : 3 sec + maxdefer : 120 sec + group : 0x00 + txoff : off + softdcd : on + SLIP : off + + Status: + + HDLC Z8530 Interrupts Buffers + ----------------------------------------------------------------------- + Sent : 273 RxOver : 0 RxInts : 125074 Size : 384 + Received : 1095 TxUnder: 0 TxInts : 4684 NoSpace : 0 + RxErrors : 1591 ExInts : 11776 + TxErrors : 0 SpInts : 1503 + Tx State : idle + + +The status info shown is: + +============== ============================================================== +Sent number of frames transmitted +Received number of frames received +RxErrors number of receive errors (CRC, ABORT) +TxErrors number of discarded Tx frames (due to various reasons) +Tx State status of the Tx interrupt handler: idle/busy/active/tail (2) +RxOver number of receiver overruns +TxUnder number of transmitter underruns +RxInts number of receiver interrupts +TxInts number of transmitter interrupts +EpInts number of receiver special condition interrupts +SpInts number of external/status interrupts +Size maximum size of an AX.25 frame (*with* AX.25 headers!) +NoSpace number of times a buffer could not get allocated +============== ============================================================== + +An overrun is abnormal. If lots of these occur, the product of +baudrate and number of interfaces is too high for the processing +power of your computer. NoSpace errors are unlikely to be caused by the +driver or the kernel AX.25. + + +3.2 Setting Parameters +====================== + + +The setting of parameters of the emulated KISS TNC is done in the +same way in the SCC driver. You can change parameters by using +the kissparms program from the ax25-utils package or use the program +"sccparam":: + + sccparam <device> <paramname> <decimal-|hexadecimal value> + +You can change the following parameters: + +=========== ===== +param value +=========== ===== +speed 1200 +txdelay 36 +persist 255 +slottime 0 +txtail 8 +fulldup 1 +waittime 12 +mintime 3 +maxkeyup 7 +idletime 3 +maxdefer 120 +group 0x00 +txoff off +softdcd on +SLIP off +=========== ===== + + +The parameters have the following meaning: + +speed: + The baudrate on this channel in bits/sec + + Example: sccparam /dev/scc3 speed 9600 + +txdelay: + The delay (in units of 10 ms) after keying of the + transmitter, until the first byte is sent. This is usually + called "TXDELAY" in a TNC. When 0 is specified, the driver + will just wait until the CTS signal is asserted. This + assumes the presence of a timer or other circuitry in the + MODEM and/or transmitter, that asserts CTS when the + transmitter is ready for data. + A normal value of this parameter is 30-36. + + Example: sccparam /dev/scc0 txd 20 + +persist: + This is the probability that the transmitter will be keyed + when the channel is found to be free. It is a value from 0 + to 255, and the probability is (value+1)/256. The value + should be somewhere near 50-60, and should be lowered when + the channel is used more heavily. + + Example: sccparam /dev/scc2 persist 20 + +slottime: + This is the time between samples of the channel. It is + expressed in units of 10 ms. About 200-300 ms (value 20-30) + seems to be a good value. + + Example: sccparam /dev/scc0 slot 20 + +tail: + The time the transmitter will remain keyed after the last + byte of a packet has been transferred to the SCC. This is + necessary because the CRC and a flag still have to leave the + SCC before the transmitter is keyed down. The value depends + on the baudrate selected. A few character times should be + sufficient, e.g. 40ms at 1200 baud. (value 4) + The value of this parameter is in 10 ms units. + + Example: sccparam /dev/scc2 4 + +full: + The full-duplex mode switch. This can be one of the following + values: + + 0: The interface will operate in CSMA mode (the normal + half-duplex packet radio operation) + 1: Fullduplex mode, i.e. the transmitter will be keyed at + any time, without checking the received carrier. It + will be unkeyed when there are no packets to be sent. + 2: Like 1, but the transmitter will remain keyed, also + when there are no packets to be sent. Flags will be + sent in that case, until a timeout (parameter 10) + occurs. + + Example: sccparam /dev/scc0 fulldup off + +wait: + The initial waittime before any transmit attempt, after the + frame has been queue for transmit. This is the length of + the first slot in CSMA mode. In full duplex modes it is + set to 0 for maximum performance. + The value of this parameter is in 10 ms units. + + Example: sccparam /dev/scc1 wait 4 + +maxkey: + The maximal time the transmitter will be keyed to send + packets, in seconds. This can be useful on busy CSMA + channels, to avoid "getting a bad reputation" when you are + generating a lot of traffic. After the specified time has + elapsed, no new frame will be started. Instead, the trans- + mitter will be switched off for a specified time (parameter + min), and then the selected algorithm for keyup will be + started again. + The value 0 as well as "off" will disable this feature, + and allow infinite transmission time. + + Example: sccparam /dev/scc0 maxk 20 + +min: + This is the time the transmitter will be switched off when + the maximum transmission time is exceeded. + + Example: sccparam /dev/scc3 min 10 + +idle: + This parameter specifies the maximum idle time in full duplex + 2 mode, in seconds. When no frames have been sent for this + time, the transmitter will be keyed down. A value of 0 is + has same result as the fullduplex mode 1. This parameter + can be disabled. + + Example: sccparam /dev/scc2 idle off # transmit forever + +maxdefer + This is the maximum time (in seconds) to wait for a free channel + to send. When this timer expires the transmitter will be keyed + IMMEDIATELY. If you love to get trouble with other users you + should set this to a very low value ;-) + + Example: sccparam /dev/scc0 maxdefer 240 # 2 minutes + + +txoff: + When this parameter has the value 0, the transmission of packets + is enable. Otherwise it is disabled. + + Example: sccparam /dev/scc2 txoff on + +group: + It is possible to build special radio equipment to use more than + one frequency on the same band, e.g. using several receivers and + only one transmitter that can be switched between frequencies. + Also, you can connect several radios that are active on the same + band. In these cases, it is not possible, or not a good idea, to + transmit on more than one frequency. The SCC driver provides a + method to lock transmitters on different interfaces, using the + "param <interface> group <x>" command. This will only work when + you are using CSMA mode (parameter full = 0). + + The number <x> must be 0 if you want no group restrictions, and + can be computed as follows to create restricted groups: + <x> is the sum of some OCTAL numbers: + + + === ======================================================= + 200 This transmitter will only be keyed when all other + transmitters in the group are off. + 100 This transmitter will only be keyed when the carrier + detect of all other interfaces in the group is off. + 0xx A byte that can be used to define different groups. + Interfaces are in the same group, when the logical AND + between their xx values is nonzero. + === ======================================================= + + Examples: + + When 2 interfaces use group 201, their transmitters will never be + keyed at the same time. + + When 2 interfaces use group 101, the transmitters will only key + when both channels are clear at the same time. When group 301, + the transmitters will not be keyed at the same time. + + Don't forget to convert the octal numbers into decimal before + you set the parameter. + + Example: (to be written) + +softdcd: + use a software dcd instead of the real one... Useful for a very + slow squelch. + + Example: sccparam /dev/scc0 soft on + + +4. Problems +=========== + +If you have tx-problems with your BayCom USCC card please check +the manufacturer of the 8530. SGS chips have a slightly +different timing. Try Zilog... A solution is to write to register 8 +instead to the data port, but this won't work with the ESCC chips. +*SIGH!* + +A very common problem is that the PTT locks until the maxkeyup timer +expires, although interrupts and clock source are correct. In most +cases compiling the driver with CONFIG_SCC_DELAY (set with +make config) solves the problems. For more hints read the (pseudo) FAQ +and the documentation coming with z8530drv-utils. + +I got reports that the driver has problems on some 386-based systems. +(i.e. Amstrad) Those systems have a bogus AT bus timing which will +lead to delayed answers on interrupts. You can recognize these +problems by looking at the output of Sccstat for the suspected +port. If it shows under- and overruns you own such a system. + +Delayed processing of received data: This depends on + +- the kernel version + +- kernel profiling compiled or not + +- a high interrupt load + +- a high load of the machine --- running X, Xmorph, XV and Povray, + while compiling the kernel... hmm ... even with 32 MB RAM ... ;-) + Or running a named for the whole .ampr.org domain on an 8 MB + box... + +- using information from rxecho or kissbridge. + +Kernel panics: please read /linux/README and find out if it +really occurred within the scc driver. + +If you cannot solve a problem, send me + +- a description of the problem, +- information on your hardware (computer system, scc board, modem) +- your kernel version +- the output of cat /proc/net/z8530 + +4. Thor RLC100 +============== + +Mysteriously this board seems not to work with the driver. Anyone +got it up-and-running? + + +Many thanks to Linus Torvalds and Alan Cox for including the driver +in the Linux standard distribution and their support. + +:: + + Joerg Reuter ampr-net: dl1bke@db0pra.ampr.org + AX-25 : DL1BKE @ DB0ABH.#BAY.DEU.EU + Internet: jreuter@yaina.de + WWW : http://yaina.de/jreuter diff --git a/Documentation/networking/device_drivers/index.rst b/Documentation/networking/device_drivers/index.rst new file mode 100644 index 0000000000..601eacaf12 --- /dev/null +++ b/Documentation/networking/device_drivers/index.rst @@ -0,0 +1,28 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) + +Hardware Device Drivers +======================= + +Contents: + +.. toctree:: + :maxdepth: 2 + + appletalk/index + atm/index + cable/index + can/index + cellular/index + ethernet/index + fddi/index + hamradio/index + qlogic/index + wifi/index + wwan/index + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/qlogic/index.rst b/Documentation/networking/device_drivers/qlogic/index.rst new file mode 100644 index 0000000000..ad05b04286 --- /dev/null +++ b/Documentation/networking/device_drivers/qlogic/index.rst @@ -0,0 +1,18 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) + +QLogic QLGE Device Drivers +=============================================== + +Contents: + +.. toctree:: + :maxdepth: 2 + + qlge + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/qlogic/qlge.rst b/Documentation/networking/device_drivers/qlogic/qlge.rst new file mode 100644 index 0000000000..0b888253d1 --- /dev/null +++ b/Documentation/networking/device_drivers/qlogic/qlge.rst @@ -0,0 +1,118 @@ +.. SPDX-License-Identifier: GPL-2.0 + +======================================= +QLogic QLGE 10Gb Ethernet device driver +======================================= + +This driver use drgn and devlink for debugging. + +Dump kernel data structures in drgn +----------------------------------- + +To dump kernel data structures, the following Python script can be used +in drgn: + +.. code-block:: python + + def align(x, a): + """the alignment a should be a power of 2 + """ + mask = a - 1 + return (x+ mask) & ~mask + + def struct_size(struct_type): + struct_str = "struct {}".format(struct_type) + return sizeof(Object(prog, struct_str, address=0x0)) + + def netdev_priv(netdevice): + NETDEV_ALIGN = 32 + return netdevice.value_() + align(struct_size("net_device"), NETDEV_ALIGN) + + name = 'xxx' + qlge_device = None + netdevices = prog['init_net'].dev_base_head.address_of_() + for netdevice in list_for_each_entry("struct net_device", netdevices, "dev_list"): + if netdevice.name.string_().decode('ascii') == name: + print(netdevice.name) + + ql_adapter = Object(prog, "struct ql_adapter", address=netdev_priv(qlge_device)) + +The struct ql_adapter will be printed in drgn as follows, + + >>> ql_adapter + (struct ql_adapter){ + .ricb = (struct ricb){ + .base_cq = (u8)0, + .flags = (u8)120, + .mask = (__le16)26637, + .hash_cq_id = (u8 [1024]){ 172, 142, 255, 255 }, + .ipv6_hash_key = (__le32 [10]){}, + .ipv4_hash_key = (__le32 [4]){}, + }, + .flags = (unsigned long)0, + .wol = (u32)0, + .nic_stats = (struct nic_stats){ + .tx_pkts = (u64)0, + .tx_bytes = (u64)0, + .tx_mcast_pkts = (u64)0, + .tx_bcast_pkts = (u64)0, + .tx_ucast_pkts = (u64)0, + .tx_ctl_pkts = (u64)0, + .tx_pause_pkts = (u64)0, + ... + }, + .active_vlans = (unsigned long [64]){ + 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 52780853100545, 18446744073709551615, + 18446619461681283072, 0, 42949673024, 2147483647, + }, + .rx_ring = (struct rx_ring [17]){ + { + .cqicb = (struct cqicb){ + .msix_vect = (u8)0, + .reserved1 = (u8)0, + .reserved2 = (u8)0, + .flags = (u8)0, + .len = (__le16)0, + .rid = (__le16)0, + ... + }, + .cq_base = (void *)0x0, + .cq_base_dma = (dma_addr_t)0, + } + ... + } + } + +coredump via devlink +-------------------- + + +And the coredump obtained via devlink in json format looks like, + +.. code:: shell + + $ devlink health dump show DEVICE reporter coredump -p -j + { + "Core Registers": { + "segment": 1, + "values": [ 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 ] + }, + "Test Logic Regs": { + "segment": 2, + "values": [ 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 ] + }, + "RMII Registers": { + "segment": 3, + "values": [ 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 ] + }, + ... + "Sem Registers": { + "segment": 50, + "values": [ 0,0,0,0 ] + } + } + +When the module parameter qlge_force_coredump is set to be true, the MPI +RISC reset before coredumping. So coredumping will much longer since +devlink tool has to wait for 5 secs for the resetting to be +finished. diff --git a/Documentation/networking/device_drivers/wifi/index.rst b/Documentation/networking/device_drivers/wifi/index.rst new file mode 100644 index 0000000000..bf91a87c7a --- /dev/null +++ b/Documentation/networking/device_drivers/wifi/index.rst @@ -0,0 +1,20 @@ +.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) + +Wi-Fi Device Drivers +==================== + +Contents: + +.. toctree:: + :maxdepth: 2 + + intel/ipw2100 + intel/ipw2200 + ray_cs + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/wifi/intel/ipw2100.rst b/Documentation/networking/device_drivers/wifi/intel/ipw2100.rst new file mode 100644 index 0000000000..883e963557 --- /dev/null +++ b/Documentation/networking/device_drivers/wifi/intel/ipw2100.rst @@ -0,0 +1,323 @@ +.. SPDX-License-Identifier: GPL-2.0 +.. include:: <isonum.txt> + +=========================================== +Intel(R) PRO/Wireless 2100 Driver for Linux +=========================================== + +Support for: + +- Intel(R) PRO/Wireless 2100 Network Connection + +Copyright |copy| 2003-2006, Intel Corporation + +README.ipw2100 + +:Version: git-1.1.5 +:Date: January 25, 2006 + +.. Index + + 0. IMPORTANT INFORMATION BEFORE USING THIS DRIVER + 1. Introduction + 2. Release git-1.1.5 Current Features + 3. Command Line Parameters + 4. Sysfs Helper Files + 5. Radio Kill Switch + 6. Dynamic Firmware + 7. Power Management + 8. Support + 9. License + + +0. IMPORTANT INFORMATION BEFORE USING THIS DRIVER +================================================= + +Important Notice FOR ALL USERS OR DISTRIBUTORS!!!! + +Intel wireless LAN adapters are engineered, manufactured, tested, and +quality checked to ensure that they meet all necessary local and +governmental regulatory agency requirements for the regions that they +are designated and/or marked to ship into. Since wireless LANs are +generally unlicensed devices that share spectrum with radars, +satellites, and other licensed and unlicensed devices, it is sometimes +necessary to dynamically detect, avoid, and limit usage to avoid +interference with these devices. In many instances Intel is required to +provide test data to prove regional and local compliance to regional and +governmental regulations before certification or approval to use the +product is granted. Intel's wireless LAN's EEPROM, firmware, and +software driver are designed to carefully control parameters that affect +radio operation and to ensure electromagnetic compliance (EMC). These +parameters include, without limitation, RF power, spectrum usage, +channel scanning, and human exposure. + +For these reasons Intel cannot permit any manipulation by third parties +of the software provided in binary format with the wireless WLAN +adapters (e.g., the EEPROM and firmware). Furthermore, if you use any +patches, utilities, or code with the Intel wireless LAN adapters that +have been manipulated by an unauthorized party (i.e., patches, +utilities, or code (including open source code modifications) which have +not been validated by Intel), (i) you will be solely responsible for +ensuring the regulatory compliance of the products, (ii) Intel will bear +no liability, under any theory of liability for any issues associated +with the modified products, including without limitation, claims under +the warranty and/or issues arising from regulatory non-compliance, and +(iii) Intel will not provide or be required to assist in providing +support to any third parties for such modified products. + +Note: Many regulatory agencies consider Wireless LAN adapters to be +modules, and accordingly, condition system-level regulatory approval +upon receipt and review of test data documenting that the antennas and +system configuration do not cause the EMC and radio operation to be +non-compliant. + +The drivers available for download from SourceForge are provided as a +part of a development project. Conformance to local regulatory +requirements is the responsibility of the individual developer. As +such, if you are interested in deploying or shipping a driver as part of +solution intended to be used for purposes other than development, please +obtain a tested driver from Intel Customer Support at: + +https://www.intel.com/support/wireless/sb/CS-006408.htm + +1. Introduction +=============== + +This document provides a brief overview of the features supported by the +IPW2100 driver project. The main project website, where the latest +development version of the driver can be found, is: + + http://ipw2100.sourceforge.net + +There you can find the not only the latest releases, but also information about +potential fixes and patches, as well as links to the development mailing list +for the driver project. + + +2. Release git-1.1.5 Current Supported Features +=============================================== + +- Managed (BSS) and Ad-Hoc (IBSS) +- WEP (shared key and open) +- Wireless Tools support +- 802.1x (tested with XSupplicant 1.0.1) + +Enabled (but not supported) features: +- Monitor/RFMon mode +- WPA/WPA2 + +The distinction between officially supported and enabled is a reflection +on the amount of validation and interoperability testing that has been +performed on a given feature. + + +3. Command Line Parameters +========================== + +If the driver is built as a module, the following optional parameters are used +by entering them on the command line with the modprobe command using this +syntax:: + + modprobe ipw2100 [<option>=<VAL1><,VAL2>...] + +For example, to disable the radio on driver loading, enter: + + modprobe ipw2100 disable=1 + +The ipw2100 driver supports the following module parameters: + +========= ============== ============ ============================== +Name Value Example Meaning +========= ============== ============ ============================== +debug 0x0-0xffffffff debug=1024 Debug level set to 1024 +mode 0,1,2 mode=1 AdHoc +channel int channel=3 Only valid in AdHoc or Monitor +associate boolean associate=0 Do NOT auto associate +disable boolean disable=1 Do not power the HW +========= ============== ============ ============================== + + +4. Sysfs Helper Files +===================== + +There are several ways to control the behavior of the driver. Many of the +general capabilities are exposed through the Wireless Tools (iwconfig). There +are a few capabilities that are exposed through entries in the Linux Sysfs. + + +**Driver Level** + +For the driver level files, look in /sys/bus/pci/drivers/ipw2100/ + + debug_level + This controls the same global as the 'debug' module parameter. For + information on the various debugging levels available, run the 'dvals' + script found in the driver source directory. + + .. note:: + + 'debug_level' is only enabled if CONFIG_IPW2100_DEBUG is turn on. + +**Device Level** + +For the device level files look in:: + + /sys/bus/pci/drivers/ipw2100/{PCI-ID}/ + +For example:: + + /sys/bus/pci/drivers/ipw2100/0000:02:01.0 + +For the device level files, see /sys/bus/pci/drivers/ipw2100: + + rf_kill + read + + == ========================================= + 0 RF kill not enabled (radio on) + 1 SW based RF kill active (radio off) + 2 HW based RF kill active (radio off) + 3 Both HW and SW RF kill active (radio off) + == ========================================= + + write + + == ================================================== + 0 If SW based RF kill active, turn the radio back on + 1 If radio is on, activate SW based RF kill + == ================================================== + + .. note:: + + If you enable the SW based RF kill and then toggle the HW + based RF kill from ON -> OFF -> ON, the radio will NOT come back on + + +5. Radio Kill Switch +==================== + +Most laptops provide the ability for the user to physically disable the radio. +Some vendors have implemented this as a physical switch that requires no +software to turn the radio off and on. On other laptops, however, the switch +is controlled through a button being pressed and a software driver then making +calls to turn the radio off and on. This is referred to as a "software based +RF kill switch" + +See the Sysfs helper file 'rf_kill' for determining the state of the RF switch +on your system. + + +6. Dynamic Firmware +=================== + +As the firmware is licensed under a restricted use license, it can not be +included within the kernel sources. To enable the IPW2100 you will need a +firmware image to load into the wireless NIC's processors. + +You can obtain these images from <http://ipw2100.sf.net/firmware.php>. + +See INSTALL for instructions on installing the firmware. + + +7. Power Management +=================== + +The IPW2100 supports the configuration of the Power Save Protocol +through a private wireless extension interface. The IPW2100 supports +the following different modes: + + === =========================================================== + off No power management. Radio is always on. + on Automatic power management + 1-5 Different levels of power management. The higher the + number the greater the power savings, but with an impact to + packet latencies. + === =========================================================== + +Power management works by powering down the radio after a certain +interval of time has passed where no packets are passed through the +radio. Once powered down, the radio remains in that state for a given +period of time. For higher power savings, the interval between last +packet processed to sleep is shorter and the sleep period is longer. + +When the radio is asleep, the access point sending data to the station +must buffer packets at the AP until the station wakes up and requests +any buffered packets. If you have an AP that does not correctly support +the PSP protocol you may experience packet loss or very poor performance +while power management is enabled. If this is the case, you will need +to try and find a firmware update for your AP, or disable power +management (via ``iwconfig eth1 power off``) + +To configure the power level on the IPW2100 you use a combination of +iwconfig and iwpriv. iwconfig is used to turn power management on, off, +and set it to auto. + + ========================= ==================================== + iwconfig eth1 power off Disables radio power down + iwconfig eth1 power on Enables radio power management to + last set level (defaults to AUTO) + iwpriv eth1 set_power 0 Sets power level to AUTO and enables + power management if not previously + enabled. + iwpriv eth1 set_power 1-5 Set the power level as specified, + enabling power management if not + previously enabled. + ========================= ==================================== + +You can view the current power level setting via:: + + iwpriv eth1 get_power + +It will return the current period or timeout that is configured as a string +in the form of xxxx/yyyy (z) where xxxx is the timeout interval (amount of +time after packet processing), yyyy is the period to sleep (amount of time to +wait before powering the radio and querying the access point for buffered +packets), and z is the 'power level'. If power management is turned off the +xxxx/yyyy will be replaced with 'off' -- the level reported will be the active +level if `iwconfig eth1 power on` is invoked. + + +8. Support +========== + +For general development information and support, +go to: + + http://ipw2100.sf.net/ + +The ipw2100 1.1.0 driver and firmware can be downloaded from: + + http://support.intel.com + +For installation support on the ipw2100 1.1.0 driver on Linux kernels +2.6.8 or greater, email support is available from: + + http://supportmail.intel.com + +9. License +========== + + Copyright |copy| 2003 - 2006 Intel Corporation. All rights reserved. + + This program is free software; you can redistribute it and/or modify it + under the terms of the GNU General Public License (version 2) as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., 59 + Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + The full GNU General Public License is included in this distribution in the + file called LICENSE. + + License Contact Information: + + James P. Ketrenos <ipw2100-admin@linux.intel.com> + + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + diff --git a/Documentation/networking/device_drivers/wifi/intel/ipw2200.rst b/Documentation/networking/device_drivers/wifi/intel/ipw2200.rst new file mode 100644 index 0000000000..0cb42d2fd7 --- /dev/null +++ b/Documentation/networking/device_drivers/wifi/intel/ipw2200.rst @@ -0,0 +1,526 @@ +.. SPDX-License-Identifier: GPL-2.0 +.. include:: <isonum.txt> + +============================================== +Intel(R) PRO/Wireless 2915ABG Driver for Linux +============================================== + + +Support for: + +- Intel(R) PRO/Wireless 2200BG Network Connection +- Intel(R) PRO/Wireless 2915ABG Network Connection + +Note: The Intel(R) PRO/Wireless 2915ABG Driver for Linux and Intel(R) +PRO/Wireless 2200BG Driver for Linux is a unified driver that works on +both hardware adapters listed above. In this document the Intel(R) +PRO/Wireless 2915ABG Driver for Linux will be used to reference the +unified driver. + +Copyright |copy| 2004-2006, Intel Corporation + +README.ipw2200 + +:Version: 1.1.2 +:Date: March 30, 2006 + + +.. Index + + 0. IMPORTANT INFORMATION BEFORE USING THIS DRIVER + 1. Introduction + 1.1. Overview of features + 1.2. Module parameters + 1.3. Wireless Extension Private Methods + 1.4. Sysfs Helper Files + 1.5. Supported channels + 2. Ad-Hoc Networking + 3. Interacting with Wireless Tools + 3.1. iwconfig mode + 3.2. iwconfig sens + 4. About the Version Numbers + 5. Firmware installation + 6. Support + 7. License + + +0. IMPORTANT INFORMATION BEFORE USING THIS DRIVER +================================================= + +Important Notice FOR ALL USERS OR DISTRIBUTORS!!!! + +Intel wireless LAN adapters are engineered, manufactured, tested, and +quality checked to ensure that they meet all necessary local and +governmental regulatory agency requirements for the regions that they +are designated and/or marked to ship into. Since wireless LANs are +generally unlicensed devices that share spectrum with radars, +satellites, and other licensed and unlicensed devices, it is sometimes +necessary to dynamically detect, avoid, and limit usage to avoid +interference with these devices. In many instances Intel is required to +provide test data to prove regional and local compliance to regional and +governmental regulations before certification or approval to use the +product is granted. Intel's wireless LAN's EEPROM, firmware, and +software driver are designed to carefully control parameters that affect +radio operation and to ensure electromagnetic compliance (EMC). These +parameters include, without limitation, RF power, spectrum usage, +channel scanning, and human exposure. + +For these reasons Intel cannot permit any manipulation by third parties +of the software provided in binary format with the wireless WLAN +adapters (e.g., the EEPROM and firmware). Furthermore, if you use any +patches, utilities, or code with the Intel wireless LAN adapters that +have been manipulated by an unauthorized party (i.e., patches, +utilities, or code (including open source code modifications) which have +not been validated by Intel), (i) you will be solely responsible for +ensuring the regulatory compliance of the products, (ii) Intel will bear +no liability, under any theory of liability for any issues associated +with the modified products, including without limitation, claims under +the warranty and/or issues arising from regulatory non-compliance, and +(iii) Intel will not provide or be required to assist in providing +support to any third parties for such modified products. + +Note: Many regulatory agencies consider Wireless LAN adapters to be +modules, and accordingly, condition system-level regulatory approval +upon receipt and review of test data documenting that the antennas and +system configuration do not cause the EMC and radio operation to be +non-compliant. + +The drivers available for download from SourceForge are provided as a +part of a development project. Conformance to local regulatory +requirements is the responsibility of the individual developer. As +such, if you are interested in deploying or shipping a driver as part of +solution intended to be used for purposes other than development, please +obtain a tested driver from Intel Customer Support at: + +http://support.intel.com + + +1. Introduction +=============== + +The following sections attempt to provide a brief introduction to using +the Intel(R) PRO/Wireless 2915ABG Driver for Linux. + +This document is not meant to be a comprehensive manual on +understanding or using wireless technologies, but should be sufficient +to get you moving without wires on Linux. + +For information on building and installing the driver, see the INSTALL +file. + + +1.1. Overview of Features +------------------------- +The current release (1.1.2) supports the following features: + ++ BSS mode (Infrastructure, Managed) ++ IBSS mode (Ad-Hoc) ++ WEP (OPEN and SHARED KEY mode) ++ 802.1x EAP via wpa_supplicant and xsupplicant ++ Wireless Extension support ++ Full B and G rate support (2200 and 2915) ++ Full A rate support (2915 only) ++ Transmit power control ++ S state support (ACPI suspend/resume) + +The following features are currently enabled, but not officially +supported: + ++ WPA ++ long/short preamble support ++ Monitor mode (aka RFMon) + +The distinction between officially supported and enabled is a reflection +on the amount of validation and interoperability testing that has been +performed on a given feature. + + + +1.2. Command Line Parameters +---------------------------- + +Like many modules used in the Linux kernel, the Intel(R) PRO/Wireless +2915ABG Driver for Linux allows configuration options to be provided +as module parameters. The most common way to specify a module parameter +is via the command line. + +The general form is:: + + % modprobe ipw2200 parameter=value + +Where the supported parameter are: + + associate + Set to 0 to disable the auto scan-and-associate functionality of the + driver. If disabled, the driver will not attempt to scan + for and associate to a network until it has been configured with + one or more properties for the target network, for example configuring + the network SSID. Default is 0 (do not auto-associate) + + Example: % modprobe ipw2200 associate=0 + + auto_create + Set to 0 to disable the auto creation of an Ad-Hoc network + matching the channel and network name parameters provided. + Default is 1. + + channel + channel number for association. The normal method for setting + the channel would be to use the standard wireless tools + (i.e. `iwconfig eth1 channel 10`), but it is useful sometimes + to set this while debugging. Channel 0 means 'ANY' + + debug + If using a debug build, this is used to control the amount of debug + info is logged. See the 'dvals' and 'load' script for more info on + how to use this (the dvals and load scripts are provided as part + of the ipw2200 development snapshot releases available from the + SourceForge project at http://ipw2200.sf.net) + + led + Can be used to turn on experimental LED code. + 0 = Off, 1 = On. Default is 1. + + mode + Can be used to set the default mode of the adapter. + 0 = Managed, 1 = Ad-Hoc, 2 = Monitor + + +1.3. Wireless Extension Private Methods +--------------------------------------- + +As an interface designed to handle generic hardware, there are certain +capabilities not exposed through the normal Wireless Tool interface. As +such, a provision is provided for a driver to declare custom, or +private, methods. The Intel(R) PRO/Wireless 2915ABG Driver for Linux +defines several of these to configure various settings. + +The general form of using the private wireless methods is:: + + % iwpriv $IFNAME method parameters + +Where $IFNAME is the interface name the device is registered with +(typically eth1, customized via one of the various network interface +name managers, such as ifrename) + +The supported private methods are: + + get_mode + Can be used to report out which IEEE mode the driver is + configured to support. Example: + + % iwpriv eth1 get_mode + eth1 get_mode:802.11bg (6) + + set_mode + Can be used to configure which IEEE mode the driver will + support. + + Usage:: + + % iwpriv eth1 set_mode {mode} + + Where {mode} is a number in the range 1-7: + + == ===================== + 1 802.11a (2915 only) + 2 802.11b + 3 802.11ab (2915 only) + 4 802.11g + 5 802.11ag (2915 only) + 6 802.11bg + 7 802.11abg (2915 only) + == ===================== + + get_preamble + Can be used to report configuration of preamble length. + + set_preamble + Can be used to set the configuration of preamble length: + + Usage:: + + % iwpriv eth1 set_preamble {mode} + + Where {mode} is one of: + + == ======================================== + 1 Long preamble only + 0 Auto (long or short based on connection) + == ======================================== + + +1.4. Sysfs Helper Files +----------------------- + +The Linux kernel provides a pseudo file system that can be used to +access various components of the operating system. The Intel(R) +PRO/Wireless 2915ABG Driver for Linux exposes several configuration +parameters through this mechanism. + +An entry in the sysfs can support reading and/or writing. You can +typically query the contents of a sysfs entry through the use of cat, +and can set the contents via echo. For example:: + + % cat /sys/bus/pci/drivers/ipw2200/debug_level + +Will report the current debug level of the driver's logging subsystem +(only available if CONFIG_IPW2200_DEBUG was configured when the driver +was built). + +You can set the debug level via:: + + % echo $VALUE > /sys/bus/pci/drivers/ipw2200/debug_level + +Where $VALUE would be a number in the case of this sysfs entry. The +input to sysfs files does not have to be a number. For example, the +firmware loader used by hotplug utilizes sysfs entries for transferring +the firmware image from user space into the driver. + +The Intel(R) PRO/Wireless 2915ABG Driver for Linux exposes sysfs entries +at two levels -- driver level, which apply to all instances of the driver +(in the event that there are more than one device installed) and device +level, which applies only to the single specific instance. + + +1.4.1 Driver Level Sysfs Helper Files +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +For the driver level files, look in /sys/bus/pci/drivers/ipw2200/ + + debug_level + This controls the same global as the 'debug' module parameter + + + +1.4.2 Device Level Sysfs Helper Files +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +For the device level files, look in:: + + /sys/bus/pci/drivers/ipw2200/{PCI-ID}/ + +For example::: + + /sys/bus/pci/drivers/ipw2200/0000:02:01.0 + +For the device level files, see /sys/bus/pci/drivers/ipw2200: + + rf_kill + read - + + == ========================================= + 0 RF kill not enabled (radio on) + 1 SW based RF kill active (radio off) + 2 HW based RF kill active (radio off) + 3 Both HW and SW RF kill active (radio off) + == ========================================= + + write - + + == ================================================== + 0 If SW based RF kill active, turn the radio back on + 1 If radio is on, activate SW based RF kill + == ================================================== + + .. note:: + + If you enable the SW based RF kill and then toggle the HW + based RF kill from ON -> OFF -> ON, the radio will NOT come back on + + ucode + read-only access to the ucode version number + + led + read - + + == ================= + 0 LED code disabled + 1 LED code enabled + == ================= + + write - + + == ================ + 0 Disable LED code + 1 Enable LED code + == ================ + + + .. note:: + + The LED code has been reported to hang some systems when + running ifconfig and is therefore disabled by default. + + +1.5. Supported channels +----------------------- + +Upon loading the Intel(R) PRO/Wireless 2915ABG Driver for Linux, a +message stating the detected geography code and the number of 802.11 +channels supported by the card will be displayed in the log. + +The geography code corresponds to a regulatory domain as shown in the +table below. + + +------+----------------------------+--------------------+ + | | | Supported channels | + | Code | Geography +----------+---------+ + | | | 802.11bg | 802.11a | + +======+============================+==========+=========+ + | --- | Restricted | 11 | 0 | + +------+----------------------------+----------+---------+ + | ZZF | Custom US/Canada | 11 | 8 | + +------+----------------------------+----------+---------+ + | ZZD | Rest of World | 13 | 0 | + +------+----------------------------+----------+---------+ + | ZZA | Custom USA & Europe & High | 11 | 13 | + +------+----------------------------+----------+---------+ + | ZZB | Custom NA & Europe | 11 | 13 | + +------+----------------------------+----------+---------+ + | ZZC | Custom Japan | 11 | 4 | + +------+----------------------------+----------+---------+ + | ZZM | Custom | 11 | 0 | + +------+----------------------------+----------+---------+ + | ZZE | Europe | 13 | 19 | + +------+----------------------------+----------+---------+ + | ZZJ | Custom Japan | 14 | 4 | + +------+----------------------------+----------+---------+ + | ZZR | Rest of World | 14 | 0 | + +------+----------------------------+----------+---------+ + | ZZH | High Band | 13 | 4 | + +------+----------------------------+----------+---------+ + | ZZG | Custom Europe | 13 | 4 | + +------+----------------------------+----------+---------+ + | ZZK | Europe | 13 | 24 | + +------+----------------------------+----------+---------+ + | ZZL | Europe | 11 | 13 | + +------+----------------------------+----------+---------+ + +2. Ad-Hoc Networking +===================== + +When using a device in an Ad-Hoc network, it is useful to understand the +sequence and requirements for the driver to be able to create, join, or +merge networks. + +The following attempts to provide enough information so that you can +have a consistent experience while using the driver as a member of an +Ad-Hoc network. + +2.1. Joining an Ad-Hoc Network +------------------------------ + +The easiest way to get onto an Ad-Hoc network is to join one that +already exists. + +2.2. Creating an Ad-Hoc Network +------------------------------- + +An Ad-Hoc networks is created using the syntax of the Wireless tool. + +For Example: +iwconfig eth1 mode ad-hoc essid testing channel 2 + +2.3. Merging Ad-Hoc Networks +---------------------------- + + +3. Interaction with Wireless Tools +================================== + +3.1 iwconfig mode +----------------- + +When configuring the mode of the adapter, all run-time configured parameters +are reset to the value used when the module was loaded. This includes +channels, rates, ESSID, etc. + +3.2 iwconfig sens +----------------- + +The 'iwconfig ethX sens XX' command will not set the signal sensitivity +threshold, as described in iwconfig documentation, but rather the number +of consecutive missed beacons that will trigger handover, i.e. roaming +to another access point. At the same time, it will set the disassociation +threshold to 3 times the given value. + + +4. About the Version Numbers +============================= + +Due to the nature of open source development projects, there are +frequently changes being incorporated that have not gone through +a complete validation process. These changes are incorporated into +development snapshot releases. + +Releases are numbered with a three level scheme: + + major.minor.development + +Any version where the 'development' portion is 0 (for example +1.0.0, 1.1.0, etc.) indicates a stable version that will be made +available for kernel inclusion. + +Any version where the 'development' portion is not a 0 (for +example 1.0.1, 1.1.5, etc.) indicates a development version that is +being made available for testing and cutting edge users. The stability +and functionality of the development releases are not know. We make +efforts to try and keep all snapshots reasonably stable, but due to the +frequency of their release, and the desire to get those releases +available as quickly as possible, unknown anomalies should be expected. + +The major version number will be incremented when significant changes +are made to the driver. Currently, there are no major changes planned. + +5. Firmware installation +======================== + +The driver requires a firmware image, download it and extract the +files under /lib/firmware (or wherever your hotplug's firmware.agent +will look for firmware files) + +The firmware can be downloaded from the following URL: + + http://ipw2200.sf.net/ + + +6. Support +========== + +For direct support of the 1.0.0 version, you can contact +http://supportmail.intel.com, or you can use the open source project +support. + +For general information and support, go to: + + http://ipw2200.sf.net/ + + +7. License +========== + + Copyright |copy| 2003 - 2006 Intel Corporation. All rights reserved. + + This program is free software; you can redistribute it and/or modify it + under the terms of the GNU General Public License version 2 as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., 59 + Temple Place - Suite 330, Boston, MA 02111-1307, USA. + + The full GNU General Public License is included in this distribution in the + file called LICENSE. + + Contact Information: + + James P. Ketrenos <ipw2100-admin@linux.intel.com> + + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + diff --git a/Documentation/networking/device_drivers/wifi/ray_cs.rst b/Documentation/networking/device_drivers/wifi/ray_cs.rst new file mode 100644 index 0000000000..9a46d1ae8f --- /dev/null +++ b/Documentation/networking/device_drivers/wifi/ray_cs.rst @@ -0,0 +1,165 @@ +.. SPDX-License-Identifier: GPL-2.0 + +.. include:: <isonum.txt> + +========================= +Raylink wireless LAN card +========================= + +September 21, 1999 + +Copyright |copy| 1998 Corey Thomas (corey@world.std.com) + +This file is the documentation for the Raylink Wireless LAN card driver for +Linux. The Raylink wireless LAN card is a PCMCIA card which provides IEEE +802.11 compatible wireless network connectivity at 1 and 2 megabits/second. +See http://www.raytheon.com/micro/raylink/ for more information on the Raylink +card. This driver is in early development and does have bugs. See the known +bugs and limitations at the end of this document for more information. +This driver also works with WebGear's Aviator 2.4 and Aviator Pro +wireless LAN cards. + +As of kernel 2.3.18, the ray_cs driver is part of the Linux kernel +source. My web page for the development of ray_cs is at +http://web.ralinktech.com/ralink/Home/Support/Linux.html +and I can be emailed at corey@world.std.com + +The kernel driver is based on ray_cs-1.62.tgz + +The driver at my web page is intended to be used as an add on to +David Hinds pcmcia package. All the command line parameters are +available when compiled as a module. When built into the kernel, only +the essid= string parameter is available via the kernel command line. +This will change after the method of sorting out parameters for all +the PCMCIA drivers is agreed upon. If you must have a built in driver +with nondefault parameters, they can be edited in +/usr/src/linux/drivers/net/pcmcia/ray_cs.c. Searching for module_param +will find them all. + +Information on card services is available at: + + http://pcmcia-cs.sourceforge.net/ + + +Card services user programs are still required for PCMCIA devices. +pcmcia-cs-3.1.1 or greater is required for the kernel version of +the driver. + +Currently, ray_cs is not part of David Hinds card services package, +so the following magic is required. + +At the end of the /etc/pcmcia/config.opts file, add the line: +source ./ray_cs.opts +This will make card services read the ray_cs.opts file +when starting. Create the file /etc/pcmcia/ray_cs.opts containing the +following:: + + #### start of /etc/pcmcia/ray_cs.opts ################### + # Configuration options for Raylink Wireless LAN PCMCIA card + device "ray_cs" + class "network" module "misc/ray_cs" + + card "RayLink PC Card WLAN Adapter" + manfid 0x01a6, 0x0000 + bind "ray_cs" + + module "misc/ray_cs" opts "" + #### end of /etc/pcmcia/ray_cs.opts ##################### + + +To join an existing network with +different parameters, contact the network administrator for the +configuration information, and edit /etc/pcmcia/ray_cs.opts. +Add the parameters below between the empty quotes. + +Parameters for ray_cs driver which may be specified in ray_cs.opts: + +=============== =============== ============================================= +bc integer 0 = normal mode (802.11 timing), + 1 = slow down inter frame timing to allow + operation with older breezecom access + points. + +beacon_period integer beacon period in Kilo-microseconds, + + legal values = must be integer multiple + of hop dwell + + default = 256 + +country integer 1 = USA (default), + 2 = Europe, + 3 = Japan, + 4 = Korea, + 5 = Spain, + 6 = France, + 7 = Israel, + 8 = Australia + +essid string ESS ID - network name to join + + string with maximum length of 32 chars + default value = "ADHOC_ESSID" + +hop_dwell integer hop dwell time in Kilo-microseconds + + legal values = 16,32,64,128(default),256 + +irq_mask integer linux standard 16 bit value 1bit/IRQ + + lsb is IRQ 0, bit 1 is IRQ 1 etc. + Used to restrict choice of IRQ's to use. + Recommended method for controlling + interrupts is in /etc/pcmcia/config.opts + +net_type integer 0 (default) = adhoc network, + 1 = infrastructure + +phy_addr string string containing new MAC address in + hex, must start with x eg + x00008f123456 + +psm integer 0 = continuously active, + 1 = power save mode (not useful yet) + +pc_debug integer (0-5) larger values for more verbose + logging. Replaces ray_debug. + +ray_debug integer Replaced with pc_debug + +ray_mem_speed integer defaults to 500 + +sniffer integer 0 = not sniffer (default), + 1 = sniffer which can be used to record all + network traffic using tcpdump or similar, + but no normal network use is allowed. + +translate integer 0 = no translation (encapsulate frames), + 1 = translation (RFC1042/802.1) +=============== =============== ============================================= + +More on sniffer mode: + +tcpdump does not understand 802.11 headers, so it can't +interpret the contents, but it can record to a file. This is only +useful for debugging 802.11 lowlevel protocols that are not visible to +linux. If you want to watch ftp xfers, or do similar things, you +don't need to use sniffer mode. Also, some packet types are never +sent up by the card, so you will never see them (ack, rts, cts, probe +etc.) There is a simple program (showcap) included in the ray_cs +package which parses the 802.11 headers. + +Known Problems and missing features + + Does not work with non x86 + + Does not work with SMP + + Support for defragmenting frames is not yet debugged, and in + fact is known to not work. I have never encountered a net set + up to fragment, but still, it should be fixed. + + The ioctl support is incomplete. The hardware address cannot be set + using ifconfig yet. If a different hardware address is needed, it may + be set using the phy_addr parameter in ray_cs.opts. This requires + a card insertion to take effect. diff --git a/Documentation/networking/device_drivers/wwan/index.rst b/Documentation/networking/device_drivers/wwan/index.rst new file mode 100644 index 0000000000..370d8264d5 --- /dev/null +++ b/Documentation/networking/device_drivers/wwan/index.rst @@ -0,0 +1,19 @@ +.. SPDX-License-Identifier: GPL-2.0-only + +WWAN Device Drivers +=================== + +Contents: + +.. toctree:: + :maxdepth: 2 + + iosm + t7xx + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/networking/device_drivers/wwan/iosm.rst b/Documentation/networking/device_drivers/wwan/iosm.rst new file mode 100644 index 0000000000..6f9e955af9 --- /dev/null +++ b/Documentation/networking/device_drivers/wwan/iosm.rst @@ -0,0 +1,96 @@ +.. SPDX-License-Identifier: GPL-2.0-only + +.. Copyright (C) 2020-21 Intel Corporation + +.. _iosm_driver_doc: + +=========================================== +IOSM Driver for Intel M.2 PCIe based Modems +=========================================== +The IOSM (IPC over Shared Memory) driver is a WWAN PCIe host driver developed +for linux or chrome platform for data exchange over PCIe interface between +Host platform & Intel M.2 Modem. The driver exposes interface conforming to the +MBIM protocol [1]. Any front end application ( eg: Modem Manager) could easily +manage the MBIM interface to enable data communication towards WWAN. + +Basic usage +=========== +MBIM functions are inactive when unmanaged. The IOSM driver only provides a +userspace interface MBIM "WWAN PORT" representing MBIM control channel and does +not play any role in managing the functionality. It is the job of a userspace +application to detect port enumeration and enable MBIM functionality. + +Examples of few such userspace application are: +- mbimcli (included with the libmbim [2] library), and +- Modem Manager [3] + +Management Applications to carry out below required actions for establishing +MBIM IP session: +- open the MBIM control channel +- configure network connection settings +- connect to network +- configure IP network interface + +Management application development +================================== +The driver and userspace interfaces are described below. The MBIM protocol is +described in [1] Mobile Broadband Interface Model v1.0 Errata-1. + +MBIM control channel userspace ABI +---------------------------------- + +/dev/wwan0mbim0 character device +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +The driver exposes an MBIM interface to the MBIM function by implementing +MBIM WWAN Port. The userspace end of the control channel pipe is a +/dev/wwan0mbim0 character device. Application shall use this interface for +MBIM protocol communication. + +Fragmentation +~~~~~~~~~~~~~ +The userspace application is responsible for all control message fragmentation +and defragmentation as per MBIM specification. + +/dev/wwan0mbim0 write() +~~~~~~~~~~~~~~~~~~~~~~~ +The MBIM control messages from the management application must not exceed the +negotiated control message size. + +/dev/wwan0mbim0 read() +~~~~~~~~~~~~~~~~~~~~~~ +The management application must accept control messages of up the negotiated +control message size. + +MBIM data channel userspace ABI +------------------------------- + +wwan0-X network device +~~~~~~~~~~~~~~~~~~~~~~ +The IOSM driver exposes IP link interface "wwan0-X" of type "wwan" for IP +traffic. Iproute network utility is used for creating "wwan0-X" network +interface and for associating it with MBIM IP session. The Driver supports +up to 8 IP sessions for simultaneous IP communication. + +The userspace management application is responsible for creating new IP link +prior to establishing MBIM IP session where the SessionId is greater than 0. + +For example, creating new IP link for a MBIM IP session with SessionId 1: + + ip link add dev wwan0-1 parentdev-name wwan0 type wwan linkid 1 + +The driver will automatically map the "wwan0-1" network device to MBIM IP +session 1. + +References +========== +[1] "MBIM (Mobile Broadband Interface Model) Errata-1" + - https://www.usb.org/document-library/ + +[2] libmbim - "a glib-based library for talking to WWAN modems and + devices which speak the Mobile Interface Broadband Model (MBIM) + protocol" + - http://www.freedesktop.org/wiki/Software/libmbim/ + +[3] Modem Manager - "a DBus-activated daemon which controls mobile + broadband (2G/3G/4G) devices and connections" + - http://www.freedesktop.org/wiki/Software/ModemManager/ diff --git a/Documentation/networking/device_drivers/wwan/t7xx.rst b/Documentation/networking/device_drivers/wwan/t7xx.rst new file mode 100644 index 0000000000..dd5b731957 --- /dev/null +++ b/Documentation/networking/device_drivers/wwan/t7xx.rst @@ -0,0 +1,120 @@ +.. SPDX-License-Identifier: GPL-2.0-only + +.. Copyright (C) 2020-21 Intel Corporation + +.. _t7xx_driver_doc: + +============================================ +t7xx driver for MTK PCIe based T700 5G modem +============================================ +The t7xx driver is a WWAN PCIe host driver developed for linux or Chrome OS platforms +for data exchange over PCIe interface between Host platform & MediaTek's T700 5G modem. +The driver exposes an interface conforming to the MBIM protocol [1]. Any front end +application (e.g. Modem Manager) could easily manage the MBIM interface to enable +data communication towards WWAN. The driver also provides an interface to interact +with the MediaTek's modem via AT commands. + +Basic usage +=========== +MBIM & AT functions are inactive when unmanaged. The t7xx driver provides +WWAN port userspace interfaces representing MBIM & AT control channels and does +not play any role in managing their functionality. It is the job of a userspace +application to detect port enumeration and enable MBIM & AT functionalities. + +Examples of few such userspace applications are: + +- mbimcli (included with the libmbim [2] library), and +- Modem Manager [3] + +Management Applications to carry out below required actions for establishing +MBIM IP session: + +- open the MBIM control channel +- configure network connection settings +- connect to network +- configure IP network interface + +Management Applications to carry out below required actions for send an AT +command and receive response: + +- open the AT control channel using a UART tool or a special user tool + +Management application development +================================== +The driver and userspace interfaces are described below. The MBIM protocol is +described in [1] Mobile Broadband Interface Model v1.0 Errata-1. + +MBIM control channel userspace ABI +---------------------------------- + +/dev/wwan0mbim0 character device +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +The driver exposes an MBIM interface to the MBIM function by implementing +MBIM WWAN Port. The userspace end of the control channel pipe is a +/dev/wwan0mbim0 character device. Application shall use this interface for +MBIM protocol communication. + +Fragmentation +~~~~~~~~~~~~~ +The userspace application is responsible for all control message fragmentation +and defragmentation as per MBIM specification. + +/dev/wwan0mbim0 write() +~~~~~~~~~~~~~~~~~~~~~~~ +The MBIM control messages from the management application must not exceed the +negotiated control message size. + +/dev/wwan0mbim0 read() +~~~~~~~~~~~~~~~~~~~~~~ +The management application must accept control messages of up the negotiated +control message size. + +MBIM data channel userspace ABI +------------------------------- + +wwan0-X network device +~~~~~~~~~~~~~~~~~~~~~~ +The t7xx driver exposes IP link interface "wwan0-X" of type "wwan" for IP +traffic. Iproute network utility is used for creating "wwan0-X" network +interface and for associating it with MBIM IP session. + +The userspace management application is responsible for creating new IP link +prior to establishing MBIM IP session where the SessionId is greater than 0. + +For example, creating new IP link for a MBIM IP session with SessionId 1: + + ip link add dev wwan0-1 parentdev wwan0 type wwan linkid 1 + +The driver will automatically map the "wwan0-1" network device to MBIM IP +session 1. + +AT port userspace ABI +---------------------------------- + +/dev/wwan0at0 character device +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +The driver exposes an AT port by implementing AT WWAN Port. +The userspace end of the control port is a /dev/wwan0at0 character +device. Application shall use this interface to issue AT commands. + +The MediaTek's T700 modem supports the 3GPP TS 27.007 [4] specification. + +References +========== +[1] *MBIM (Mobile Broadband Interface Model) Errata-1* + +- https://www.usb.org/document-library/ + +[2] *libmbim "a glib-based library for talking to WWAN modems and devices which +speak the Mobile Interface Broadband Model (MBIM) protocol"* + +- http://www.freedesktop.org/wiki/Software/libmbim/ + +[3] *Modem Manager "a DBus-activated daemon which controls mobile broadband +(2G/3G/4G/5G) devices and connections"* + +- http://www.freedesktop.org/wiki/Software/ModemManager/ + +[4] *Specification # 27.007 - 3GPP* + +- https://www.3gpp.org/DynaReport/27007.htm |
