diff options
Diffstat (limited to 'Documentation/power/pci.rst')
| -rw-r--r-- | Documentation/power/pci.rst | 1133 |
1 files changed, 1133 insertions, 0 deletions
diff --git a/Documentation/power/pci.rst b/Documentation/power/pci.rst new file mode 100644 index 0000000000..a125544b4c --- /dev/null +++ b/Documentation/power/pci.rst @@ -0,0 +1,1133 @@ +==================== +PCI Power Management +==================== + +Copyright (c) 2010 Rafael J. Wysocki <rjw@sisk.pl>, Novell Inc. + +An overview of concepts and the Linux kernel's interfaces related to PCI power +management. Based on previous work by Patrick Mochel <mochel@transmeta.com> +(and others). + +This document only covers the aspects of power management specific to PCI +devices. For general description of the kernel's interfaces related to device +power management refer to Documentation/driver-api/pm/devices.rst and +Documentation/power/runtime_pm.rst. + +.. contents: + + 1. Hardware and Platform Support for PCI Power Management + 2. PCI Subsystem and Device Power Management + 3. PCI Device Drivers and Power Management + 4. Resources + + +1. Hardware and Platform Support for PCI Power Management +========================================================= + +1.1. Native and Platform-Based Power Management +----------------------------------------------- + +In general, power management is a feature allowing one to save energy by putting +devices into states in which they draw less power (low-power states) at the +price of reduced functionality or performance. + +Usually, a device is put into a low-power state when it is underutilized or +completely inactive. However, when it is necessary to use the device once +again, it has to be put back into the "fully functional" state (full-power +state). This may happen when there are some data for the device to handle or +as a result of an external event requiring the device to be active, which may +be signaled by the device itself. + +PCI devices may be put into low-power states in two ways, by using the device +capabilities introduced by the PCI Bus Power Management Interface Specification, +or with the help of platform firmware, such as an ACPI BIOS. In the first +approach, that is referred to as the native PCI power management (native PCI PM) +in what follows, the device power state is changed as a result of writing a +specific value into one of its standard configuration registers. The second +approach requires the platform firmware to provide special methods that may be +used by the kernel to change the device's power state. + +Devices supporting the native PCI PM usually can generate wakeup signals called +Power Management Events (PMEs) to let the kernel know about external events +requiring the device to be active. After receiving a PME the kernel is supposed +to put the device that sent it into the full-power state. However, the PCI Bus +Power Management Interface Specification doesn't define any standard method of +delivering the PME from the device to the CPU and the operating system kernel. +It is assumed that the platform firmware will perform this task and therefore, +even though a PCI device is set up to generate PMEs, it also may be necessary to +prepare the platform firmware for notifying the CPU of the PMEs coming from the +device (e.g. by generating interrupts). + +In turn, if the methods provided by the platform firmware are used for changing +the power state of a device, usually the platform also provides a method for +preparing the device to generate wakeup signals. In that case, however, it +often also is necessary to prepare the device for generating PMEs using the +native PCI PM mechanism, because the method provided by the platform depends on +that. + +Thus in many situations both the native and the platform-based power management +mechanisms have to be used simultaneously to obtain the desired result. + +1.2. Native PCI Power Management +-------------------------------- + +The PCI Bus Power Management Interface Specification (PCI PM Spec) was +introduced between the PCI 2.1 and PCI 2.2 Specifications. It defined a +standard interface for performing various operations related to power +management. + +The implementation of the PCI PM Spec is optional for conventional PCI devices, +but it is mandatory for PCI Express devices. If a device supports the PCI PM +Spec, it has an 8 byte power management capability field in its PCI +configuration space. This field is used to describe and control the standard +features related to the native PCI power management. + +The PCI PM Spec defines 4 operating states for devices (D0-D3) and for buses +(B0-B3). The higher the number, the less power is drawn by the device or bus +in that state. However, the higher the number, the longer the latency for +the device or bus to return to the full-power state (D0 or B0, respectively). + +There are two variants of the D3 state defined by the specification. The first +one is D3hot, referred to as the software accessible D3, because devices can be +programmed to go into it. The second one, D3cold, is the state that PCI devices +are in when the supply voltage (Vcc) is removed from them. It is not possible +to program a PCI device to go into D3cold, although there may be a programmable +interface for putting the bus the device is on into a state in which Vcc is +removed from all devices on the bus. + +PCI bus power management, however, is not supported by the Linux kernel at the +time of this writing and therefore it is not covered by this document. + +Note that every PCI device can be in the full-power state (D0) or in D3cold, +regardless of whether or not it implements the PCI PM Spec. In addition to +that, if the PCI PM Spec is implemented by the device, it must support D3hot +as well as D0. The support for the D1 and D2 power states is optional. + +PCI devices supporting the PCI PM Spec can be programmed to go to any of the +supported low-power states (except for D3cold). While in D1-D3hot the +standard configuration registers of the device must be accessible to software +(i.e. the device is required to respond to PCI configuration accesses), although +its I/O and memory spaces are then disabled. This allows the device to be +programmatically put into D0. Thus the kernel can switch the device back and +forth between D0 and the supported low-power states (except for D3cold) and the +possible power state transitions the device can undergo are the following: + ++----------------------------+ +| Current State | New State | ++----------------------------+ +| D0 | D1, D2, D3 | ++----------------------------+ +| D1 | D2, D3 | ++----------------------------+ +| D2 | D3 | ++----------------------------+ +| D1, D2, D3 | D0 | ++----------------------------+ + +The transition from D3cold to D0 occurs when the supply voltage is provided to +the device (i.e. power is restored). In that case the device returns to D0 with +a full power-on reset sequence and the power-on defaults are restored to the +device by hardware just as at initial power up. + +PCI devices supporting the PCI PM Spec can be programmed to generate PMEs +while in any power state (D0-D3), but they are not required to be capable +of generating PMEs from all supported power states. In particular, the +capability of generating PMEs from D3cold is optional and depends on the +presence of additional voltage (3.3Vaux) allowing the device to remain +sufficiently active to generate a wakeup signal. + +1.3. ACPI Device Power Management +--------------------------------- + +The platform firmware support for the power management of PCI devices is +system-specific. However, if the system in question is compliant with the +Advanced Configuration and Power Interface (ACPI) Specification, like the +majority of x86-based systems, it is supposed to implement device power +management interfaces defined by the ACPI standard. + +For this purpose the ACPI BIOS provides special functions called "control +methods" that may be executed by the kernel to perform specific tasks, such as +putting a device into a low-power state. These control methods are encoded +using special byte-code language called the ACPI Machine Language (AML) and +stored in the machine's BIOS. The kernel loads them from the BIOS and executes +them as needed using an AML interpreter that translates the AML byte code into +computations and memory or I/O space accesses. This way, in theory, a BIOS +writer can provide the kernel with a means to perform actions depending +on the system design in a system-specific fashion. + +ACPI control methods may be divided into global control methods, that are not +associated with any particular devices, and device control methods, that have +to be defined separately for each device supposed to be handled with the help of +the platform. This means, in particular, that ACPI device control methods can +only be used to handle devices that the BIOS writer knew about in advance. The +ACPI methods used for device power management fall into that category. + +The ACPI specification assumes that devices can be in one of four power states +labeled as D0, D1, D2, and D3 that roughly correspond to the native PCI PM +D0-D3 states (although the difference between D3hot and D3cold is not taken +into account by ACPI). Moreover, for each power state of a device there is a +set of power resources that have to be enabled for the device to be put into +that state. These power resources are controlled (i.e. enabled or disabled) +with the help of their own control methods, _ON and _OFF, that have to be +defined individually for each of them. + +To put a device into the ACPI power state Dx (where x is a number between 0 and +3 inclusive) the kernel is supposed to (1) enable the power resources required +by the device in this state using their _ON control methods and (2) execute the +_PSx control method defined for the device. In addition to that, if the device +is going to be put into a low-power state (D1-D3) and is supposed to generate +wakeup signals from that state, the _DSW (or _PSW, replaced with _DSW by ACPI +3.0) control method defined for it has to be executed before _PSx. Power +resources that are not required by the device in the target power state and are +not required any more by any other device should be disabled (by executing their +_OFF control methods). If the current power state of the device is D3, it can +only be put into D0 this way. + +However, quite often the power states of devices are changed during a +system-wide transition into a sleep state or back into the working state. ACPI +defines four system sleep states, S1, S2, S3, and S4, and denotes the system +working state as S0. In general, the target system sleep (or working) state +determines the highest power (lowest number) state the device can be put +into and the kernel is supposed to obtain this information by executing the +device's _SxD control method (where x is a number between 0 and 4 inclusive). +If the device is required to wake up the system from the target sleep state, the +lowest power (highest number) state it can be put into is also determined by the +target state of the system. The kernel is then supposed to use the device's +_SxW control method to obtain the number of that state. It also is supposed to +use the device's _PRW control method to learn which power resources need to be +enabled for the device to be able to generate wakeup signals. + +1.4. Wakeup Signaling +--------------------- + +Wakeup signals generated by PCI devices, either as native PCI PMEs, or as +a result of the execution of the _DSW (or _PSW) ACPI control method before +putting the device into a low-power state, have to be caught and handled as +appropriate. If they are sent while the system is in the working state +(ACPI S0), they should be translated into interrupts so that the kernel can +put the devices generating them into the full-power state and take care of the +events that triggered them. In turn, if they are sent while the system is +sleeping, they should cause the system's core logic to trigger wakeup. + +On ACPI-based systems wakeup signals sent by conventional PCI devices are +converted into ACPI General-Purpose Events (GPEs) which are hardware signals +from the system core logic generated in response to various events that need to +be acted upon. Every GPE is associated with one or more sources of potentially +interesting events. In particular, a GPE may be associated with a PCI device +capable of signaling wakeup. The information on the connections between GPEs +and event sources is recorded in the system's ACPI BIOS from where it can be +read by the kernel. + +If a PCI device known to the system's ACPI BIOS signals wakeup, the GPE +associated with it (if there is one) is triggered. The GPEs associated with PCI +bridges may also be triggered in response to a wakeup signal from one of the +devices below the bridge (this also is the case for root bridges) and, for +example, native PCI PMEs from devices unknown to the system's ACPI BIOS may be +handled this way. + +A GPE may be triggered when the system is sleeping (i.e. when it is in one of +the ACPI S1-S4 states), in which case system wakeup is started by its core logic +(the device that was the source of the signal causing the system wakeup to occur +may be identified later). The GPEs used in such situations are referred to as +wakeup GPEs. + +Usually, however, GPEs are also triggered when the system is in the working +state (ACPI S0) and in that case the system's core logic generates a System +Control Interrupt (SCI) to notify the kernel of the event. Then, the SCI +handler identifies the GPE that caused the interrupt to be generated which, +in turn, allows the kernel to identify the source of the event (that may be +a PCI device signaling wakeup). The GPEs used for notifying the kernel of +events occurring while the system is in the working state are referred to as +runtime GPEs. + +Unfortunately, there is no standard way of handling wakeup signals sent by +conventional PCI devices on systems that are not ACPI-based, but there is one +for PCI Express devices. Namely, the PCI Express Base Specification introduced +a native mechanism for converting native PCI PMEs into interrupts generated by +root ports. For conventional PCI devices native PMEs are out-of-band, so they +are routed separately and they need not pass through bridges (in principle they +may be routed directly to the system's core logic), but for PCI Express devices +they are in-band messages that have to pass through the PCI Express hierarchy, +including the root port on the path from the device to the Root Complex. Thus +it was possible to introduce a mechanism by which a root port generates an +interrupt whenever it receives a PME message from one of the devices below it. +The PCI Express Requester ID of the device that sent the PME message is then +recorded in one of the root port's configuration registers from where it may be +read by the interrupt handler allowing the device to be identified. [PME +messages sent by PCI Express endpoints integrated with the Root Complex don't +pass through root ports, but instead they cause a Root Complex Event Collector +(if there is one) to generate interrupts.] + +In principle the native PCI Express PME signaling may also be used on ACPI-based +systems along with the GPEs, but to use it the kernel has to ask the system's +ACPI BIOS to release control of root port configuration registers. The ACPI +BIOS, however, is not required to allow the kernel to control these registers +and if it doesn't do that, the kernel must not modify their contents. Of course +the native PCI Express PME signaling cannot be used by the kernel in that case. + + +2. PCI Subsystem and Device Power Management +============================================ + +2.1. Device Power Management Callbacks +-------------------------------------- + +The PCI Subsystem participates in the power management of PCI devices in a +number of ways. First of all, it provides an intermediate code layer between +the device power management core (PM core) and PCI device drivers. +Specifically, the pm field of the PCI subsystem's struct bus_type object, +pci_bus_type, points to a struct dev_pm_ops object, pci_dev_pm_ops, containing +pointers to several device power management callbacks:: + + const struct dev_pm_ops pci_dev_pm_ops = { + .prepare = pci_pm_prepare, + .complete = pci_pm_complete, + .suspend = pci_pm_suspend, + .resume = pci_pm_resume, + .freeze = pci_pm_freeze, + .thaw = pci_pm_thaw, + .poweroff = pci_pm_poweroff, + .restore = pci_pm_restore, + .suspend_noirq = pci_pm_suspend_noirq, + .resume_noirq = pci_pm_resume_noirq, + .freeze_noirq = pci_pm_freeze_noirq, + .thaw_noirq = pci_pm_thaw_noirq, + .poweroff_noirq = pci_pm_poweroff_noirq, + .restore_noirq = pci_pm_restore_noirq, + .runtime_suspend = pci_pm_runtime_suspend, + .runtime_resume = pci_pm_runtime_resume, + .runtime_idle = pci_pm_runtime_idle, + }; + +These callbacks are executed by the PM core in various situations related to +device power management and they, in turn, execute power management callbacks +provided by PCI device drivers. They also perform power management operations +involving some standard configuration registers of PCI devices that device +drivers need not know or care about. + +The structure representing a PCI device, struct pci_dev, contains several fields +that these callbacks operate on:: + + struct pci_dev { + ... + pci_power_t current_state; /* Current operating state. */ + int pm_cap; /* PM capability offset in the + configuration space */ + unsigned int pme_support:5; /* Bitmask of states from which PME# + can be generated */ + unsigned int pme_poll:1; /* Poll device's PME status bit */ + unsigned int d1_support:1; /* Low power state D1 is supported */ + unsigned int d2_support:1; /* Low power state D2 is supported */ + unsigned int no_d1d2:1; /* D1 and D2 are forbidden */ + unsigned int wakeup_prepared:1; /* Device prepared for wake up */ + unsigned int d3hot_delay; /* D3hot->D0 transition time in ms */ + ... + }; + +They also indirectly use some fields of the struct device that is embedded in +struct pci_dev. + +2.2. Device Initialization +-------------------------- + +The PCI subsystem's first task related to device power management is to +prepare the device for power management and initialize the fields of struct +pci_dev used for this purpose. This happens in two functions defined in +drivers/pci/pci.c, pci_pm_init() and platform_pci_wakeup_init(). + +The first of these functions checks if the device supports native PCI PM +and if that's the case the offset of its power management capability structure +in the configuration space is stored in the pm_cap field of the device's struct +pci_dev object. Next, the function checks which PCI low-power states are +supported by the device and from which low-power states the device can generate +native PCI PMEs. The power management fields of the device's struct pci_dev and +the struct device embedded in it are updated accordingly and the generation of +PMEs by the device is disabled. + +The second function checks if the device can be prepared to signal wakeup with +the help of the platform firmware, such as the ACPI BIOS. If that is the case, +the function updates the wakeup fields in struct device embedded in the +device's struct pci_dev and uses the firmware-provided method to prevent the +device from signaling wakeup. + +At this point the device is ready for power management. For driverless devices, +however, this functionality is limited to a few basic operations carried out +during system-wide transitions to a sleep state and back to the working state. + +2.3. Runtime Device Power Management +------------------------------------ + +The PCI subsystem plays a vital role in the runtime power management of PCI +devices. For this purpose it uses the general runtime power management +(runtime PM) framework described in Documentation/power/runtime_pm.rst. +Namely, it provides subsystem-level callbacks:: + + pci_pm_runtime_suspend() + pci_pm_runtime_resume() + pci_pm_runtime_idle() + +that are executed by the core runtime PM routines. It also implements the +entire mechanics necessary for handling runtime wakeup signals from PCI devices +in low-power states, which at the time of this writing works for both the native +PCI Express PME signaling and the ACPI GPE-based wakeup signaling described in +Section 1. + +First, a PCI device is put into a low-power state, or suspended, with the help +of pm_schedule_suspend() or pm_runtime_suspend() which for PCI devices call +pci_pm_runtime_suspend() to do the actual job. For this to work, the device's +driver has to provide a pm->runtime_suspend() callback (see below), which is +run by pci_pm_runtime_suspend() as the first action. If the driver's callback +returns successfully, the device's standard configuration registers are saved, +the device is prepared to generate wakeup signals and, finally, it is put into +the target low-power state. + +The low-power state to put the device into is the lowest-power (highest number) +state from which it can signal wakeup. The exact method of signaling wakeup is +system-dependent and is determined by the PCI subsystem on the basis of the +reported capabilities of the device and the platform firmware. To prepare the +device for signaling wakeup and put it into the selected low-power state, the +PCI subsystem can use the platform firmware as well as the device's native PCI +PM capabilities, if supported. + +It is expected that the device driver's pm->runtime_suspend() callback will +not attempt to prepare the device for signaling wakeup or to put it into a +low-power state. The driver ought to leave these tasks to the PCI subsystem +that has all of the information necessary to perform them. + +A suspended device is brought back into the "active" state, or resumed, +with the help of pm_request_resume() or pm_runtime_resume() which both call +pci_pm_runtime_resume() for PCI devices. Again, this only works if the device's +driver provides a pm->runtime_resume() callback (see below). However, before +the driver's callback is executed, pci_pm_runtime_resume() brings the device +back into the full-power state, prevents it from signaling wakeup while in that +state and restores its standard configuration registers. Thus the driver's +callback need not worry about the PCI-specific aspects of the device resume. + +Note that generally pci_pm_runtime_resume() may be called in two different +situations. First, it may be called at the request of the device's driver, for +example if there are some data for it to process. Second, it may be called +as a result of a wakeup signal from the device itself (this sometimes is +referred to as "remote wakeup"). Of course, for this purpose the wakeup signal +is handled in one of the ways described in Section 1 and finally converted into +a notification for the PCI subsystem after the source device has been +identified. + +The pci_pm_runtime_idle() function, called for PCI devices by pm_runtime_idle() +and pm_request_idle(), executes the device driver's pm->runtime_idle() +callback, if defined, and if that callback doesn't return error code (or is not +present at all), suspends the device with the help of pm_runtime_suspend(). +Sometimes pci_pm_runtime_idle() is called automatically by the PM core (for +example, it is called right after the device has just been resumed), in which +cases it is expected to suspend the device if that makes sense. Usually, +however, the PCI subsystem doesn't really know if the device really can be +suspended, so it lets the device's driver decide by running its +pm->runtime_idle() callback. + +2.4. System-Wide Power Transitions +---------------------------------- +There are a few different types of system-wide power transitions, described in +Documentation/driver-api/pm/devices.rst. Each of them requires devices to be +handled in a specific way and the PM core executes subsystem-level power +management callbacks for this purpose. They are executed in phases such that +each phase involves executing the same subsystem-level callback for every device +belonging to the given subsystem before the next phase begins. These phases +always run after tasks have been frozen. + +2.4.1. System Suspend +^^^^^^^^^^^^^^^^^^^^^ + +When the system is going into a sleep state in which the contents of memory will +be preserved, such as one of the ACPI sleep states S1-S3, the phases are: + + prepare, suspend, suspend_noirq. + +The following PCI bus type's callbacks, respectively, are used in these phases:: + + pci_pm_prepare() + pci_pm_suspend() + pci_pm_suspend_noirq() + +The pci_pm_prepare() routine first puts the device into the "fully functional" +state with the help of pm_runtime_resume(). Then, it executes the device +driver's pm->prepare() callback if defined (i.e. if the driver's struct +dev_pm_ops object is present and the prepare pointer in that object is valid). + +The pci_pm_suspend() routine first checks if the device's driver implements +legacy PCI suspend routines (see Section 3), in which case the driver's legacy +suspend callback is executed, if present, and its result is returned. Next, if +the device's driver doesn't provide a struct dev_pm_ops object (containing +pointers to the driver's callbacks), pci_pm_default_suspend() is called, which +simply turns off the device's bus master capability and runs +pcibios_disable_device() to disable it, unless the device is a bridge (PCI +bridges are ignored by this routine). Next, the device driver's pm->suspend() +callback is executed, if defined, and its result is returned if it fails. +Finally, pci_fixup_device() is called to apply hardware suspend quirks related +to the device if necessary. + +Note that the suspend phase is carried out asynchronously for PCI devices, so +the pci_pm_suspend() callback may be executed in parallel for any pair of PCI +devices that don't depend on each other in a known way (i.e. none of the paths +in the device tree from the root bridge to a leaf device contains both of them). + +The pci_pm_suspend_noirq() routine is executed after suspend_device_irqs() has +been called, which means that the device driver's interrupt handler won't be +invoked while this routine is running. It first checks if the device's driver +implements legacy PCI suspends routines (Section 3), in which case the legacy +late suspend routine is called and its result is returned (the standard +configuration registers of the device are saved if the driver's callback hasn't +done that). Second, if the device driver's struct dev_pm_ops object is not +present, the device's standard configuration registers are saved and the routine +returns success. Otherwise the device driver's pm->suspend_noirq() callback is +executed, if present, and its result is returned if it fails. Next, if the +device's standard configuration registers haven't been saved yet (one of the +device driver's callbacks executed before might do that), pci_pm_suspend_noirq() +saves them, prepares the device to signal wakeup (if necessary) and puts it into +a low-power state. + +The low-power state to put the device into is the lowest-power (highest number) +state from which it can signal wakeup while the system is in the target sleep +state. Just like in the runtime PM case described above, the mechanism of +signaling wakeup is system-dependent and determined by the PCI subsystem, which +is also responsible for preparing the device to signal wakeup from the system's +target sleep state as appropriate. + +PCI device drivers (that don't implement legacy power management callbacks) are +generally not expected to prepare devices for signaling wakeup or to put them +into low-power states. However, if one of the driver's suspend callbacks +(pm->suspend() or pm->suspend_noirq()) saves the device's standard configuration +registers, pci_pm_suspend_noirq() will assume that the device has been prepared +to signal wakeup and put into a low-power state by the driver (the driver is +then assumed to have used the helper functions provided by the PCI subsystem for +this purpose). PCI device drivers are not encouraged to do that, but in some +rare cases doing that in the driver may be the optimum approach. + +2.4.2. System Resume +^^^^^^^^^^^^^^^^^^^^ + +When the system is undergoing a transition from a sleep state in which the +contents of memory have been preserved, such as one of the ACPI sleep states +S1-S3, into the working state (ACPI S0), the phases are: + + resume_noirq, resume, complete. + +The following PCI bus type's callbacks, respectively, are executed in these +phases:: + + pci_pm_resume_noirq() + pci_pm_resume() + pci_pm_complete() + +The pci_pm_resume_noirq() routine first puts the device into the full-power +state, restores its standard configuration registers and applies early resume +hardware quirks related to the device, if necessary. This is done +unconditionally, regardless of whether or not the device's driver implements +legacy PCI power management callbacks (this way all PCI devices are in the +full-power state and their standard configuration registers have been restored +when their interrupt handlers are invoked for the first time during resume, +which allows the kernel to avoid problems with the handling of shared interrupts +by drivers whose devices are still suspended). If legacy PCI power management +callbacks (see Section 3) are implemented by the device's driver, the legacy +early resume callback is executed and its result is returned. Otherwise, the +device driver's pm->resume_noirq() callback is executed, if defined, and its +result is returned. + +The pci_pm_resume() routine first checks if the device's standard configuration +registers have been restored and restores them if that's not the case (this +only is necessary in the error path during a failing suspend). Next, resume +hardware quirks related to the device are applied, if necessary, and if the +device's driver implements legacy PCI power management callbacks (see +Section 3), the driver's legacy resume callback is executed and its result is +returned. Otherwise, the device's wakeup signaling mechanisms are blocked and +its driver's pm->resume() callback is executed, if defined (the callback's +result is then returned). + +The resume phase is carried out asynchronously for PCI devices, like the +suspend phase described above, which means that if two PCI devices don't depend +on each other in a known way, the pci_pm_resume() routine may be executed for +the both of them in parallel. + +The pci_pm_complete() routine only executes the device driver's pm->complete() +callback, if defined. + +2.4.3. System Hibernation +^^^^^^^^^^^^^^^^^^^^^^^^^ + +System hibernation is more complicated than system suspend, because it requires +a system image to be created and written into a persistent storage medium. The +image is created atomically and all devices are quiesced, or frozen, before that +happens. + +The freezing of devices is carried out after enough memory has been freed (at +the time of this writing the image creation requires at least 50% of system RAM +to be free) in the following three phases: + + prepare, freeze, freeze_noirq + +that correspond to the PCI bus type's callbacks:: + + pci_pm_prepare() + pci_pm_freeze() + pci_pm_freeze_noirq() + +This means that the prepare phase is exactly the same as for system suspend. +The other two phases, however, are different. + +The pci_pm_freeze() routine is quite similar to pci_pm_suspend(), but it runs +the device driver's pm->freeze() callback, if defined, instead of pm->suspend(), +and it doesn't apply the suspend-related hardware quirks. It is executed +asynchronously for different PCI devices that don't depend on each other in a +known way. + +The pci_pm_freeze_noirq() routine, in turn, is similar to +pci_pm_suspend_noirq(), but it calls the device driver's pm->freeze_noirq() +routine instead of pm->suspend_noirq(). It also doesn't attempt to prepare the +device for signaling wakeup and put it into a low-power state. Still, it saves +the device's standard configuration registers if they haven't been saved by one +of the driver's callbacks. + +Once the image has been created, it has to be saved. However, at this point all +devices are frozen and they cannot handle I/O, while their ability to handle +I/O is obviously necessary for the image saving. Thus they have to be brought +back to the fully functional state and this is done in the following phases: + + thaw_noirq, thaw, complete + +using the following PCI bus type's callbacks:: + + pci_pm_thaw_noirq() + pci_pm_thaw() + pci_pm_complete() + +respectively. + +The first of them, pci_pm_thaw_noirq(), is analogous to pci_pm_resume_noirq(). +It puts the device into the full power state and restores its standard +configuration registers. It also executes the device driver's pm->thaw_noirq() +callback, if defined, instead of pm->resume_noirq(). + +The pci_pm_thaw() routine is similar to pci_pm_resume(), but it runs the device +driver's pm->thaw() callback instead of pm->resume(). It is executed +asynchronously for different PCI devices that don't depend on each other in a +known way. + +The complete phase is the same as for system resume. + +After saving the image, devices need to be powered down before the system can +enter the target sleep state (ACPI S4 for ACPI-based systems). This is done in +three phases: + + prepare, poweroff, poweroff_noirq + +where the prepare phase is exactly the same as for system suspend. The other +two phases are analogous to the suspend and suspend_noirq phases, respectively. +The PCI subsystem-level callbacks they correspond to:: + + pci_pm_poweroff() + pci_pm_poweroff_noirq() + +work in analogy with pci_pm_suspend() and pci_pm_poweroff_noirq(), respectively, +although they don't attempt to save the device's standard configuration +registers. + +2.4.4. System Restore +^^^^^^^^^^^^^^^^^^^^^ + +System restore requires a hibernation image to be loaded into memory and the +pre-hibernation memory contents to be restored before the pre-hibernation system +activity can be resumed. + +As described in Documentation/driver-api/pm/devices.rst, the hibernation image +is loaded into memory by a fresh instance of the kernel, called the boot kernel, +which in turn is loaded and run by a boot loader in the usual way. After the +boot kernel has loaded the image, it needs to replace its own code and data with +the code and data of the "hibernated" kernel stored within the image, called the +image kernel. For this purpose all devices are frozen just like before creating +the image during hibernation, in the + + prepare, freeze, freeze_noirq + +phases described above. However, the devices affected by these phases are only +those having drivers in the boot kernel; other devices will still be in whatever +state the boot loader left them. + +Should the restoration of the pre-hibernation memory contents fail, the boot +kernel would go through the "thawing" procedure described above, using the +thaw_noirq, thaw, and complete phases (that will only affect the devices having +drivers in the boot kernel), and then continue running normally. + +If the pre-hibernation memory contents are restored successfully, which is the +usual situation, control is passed to the image kernel, which then becomes +responsible for bringing the system back to the working state. To achieve this, +it must restore the devices' pre-hibernation functionality, which is done much +like waking up from the memory sleep state, although it involves different +phases: + + restore_noirq, restore, complete + +The first two of these are analogous to the resume_noirq and resume phases +described above, respectively, and correspond to the following PCI subsystem +callbacks:: + + pci_pm_restore_noirq() + pci_pm_restore() + +These callbacks work in analogy with pci_pm_resume_noirq() and pci_pm_resume(), +respectively, but they execute the device driver's pm->restore_noirq() and +pm->restore() callbacks, if available. + +The complete phase is carried out in exactly the same way as during system +resume. + + +3. PCI Device Drivers and Power Management +========================================== + +3.1. Power Management Callbacks +------------------------------- + +PCI device drivers participate in power management by providing callbacks to be +executed by the PCI subsystem's power management routines described above and by +controlling the runtime power management of their devices. + +At the time of this writing there are two ways to define power management +callbacks for a PCI device driver, the recommended one, based on using a +dev_pm_ops structure described in Documentation/driver-api/pm/devices.rst, and +the "legacy" one, in which the .suspend() and .resume() callbacks from struct +pci_driver are used. The legacy approach, however, doesn't allow one to define +runtime power management callbacks and is not really suitable for any new +drivers. Therefore it is not covered by this document (refer to the source code +to learn more about it). + +It is recommended that all PCI device drivers define a struct dev_pm_ops object +containing pointers to power management (PM) callbacks that will be executed by +the PCI subsystem's PM routines in various circumstances. A pointer to the +driver's struct dev_pm_ops object has to be assigned to the driver.pm field in +its struct pci_driver object. Once that has happened, the "legacy" PM callbacks +in struct pci_driver are ignored (even if they are not NULL). + +The PM callbacks in struct dev_pm_ops are not mandatory and if they are not +defined (i.e. the respective fields of struct dev_pm_ops are unset) the PCI +subsystem will handle the device in a simplified default manner. If they are +defined, though, they are expected to behave as described in the following +subsections. + +3.1.1. prepare() +^^^^^^^^^^^^^^^^ + +The prepare() callback is executed during system suspend, during hibernation +(when a hibernation image is about to be created), during power-off after +saving a hibernation image and during system restore, when a hibernation image +has just been loaded into memory. + +This callback is only necessary if the driver's device has children that in +general may be registered at any time. In that case the role of the prepare() +callback is to prevent new children of the device from being registered until +one of the resume_noirq(), thaw_noirq(), or restore_noirq() callbacks is run. + +In addition to that the prepare() callback may carry out some operations +preparing the device to be suspended, although it should not allocate memory +(if additional memory is required to suspend the device, it has to be +preallocated earlier, for example in a suspend/hibernate notifier as described +in Documentation/driver-api/pm/notifiers.rst). + +3.1.2. suspend() +^^^^^^^^^^^^^^^^ + +The suspend() callback is only executed during system suspend, after prepare() +callbacks have been executed for all devices in the system. + +This callback is expected to quiesce the device and prepare it to be put into a +low-power state by the PCI subsystem. It is not required (in fact it even is +not recommended) that a PCI driver's suspend() callback save the standard +configuration registers of the device, prepare it for waking up the system, or +put it into a low-power state. All of these operations can very well be taken +care of by the PCI subsystem, without the driver's participation. + +However, in some rare case it is convenient to carry out these operations in +a PCI driver. Then, pci_save_state(), pci_prepare_to_sleep(), and +pci_set_power_state() should be used to save the device's standard configuration +registers, to prepare it for system wakeup (if necessary), and to put it into a +low-power state, respectively. Moreover, if the driver calls pci_save_state(), +the PCI subsystem will not execute either pci_prepare_to_sleep(), or +pci_set_power_state() for its device, so the driver is then responsible for +handling the device as appropriate. + +While the suspend() callback is being executed, the driver's interrupt handler +can be invoked to handle an interrupt from the device, so all suspend-related +operations relying on the driver's ability to handle interrupts should be +carried out in this callback. + +3.1.3. suspend_noirq() +^^^^^^^^^^^^^^^^^^^^^^ + +The suspend_noirq() callback is only executed during system suspend, after +suspend() callbacks have been executed for all devices in the system and +after device interrupts have been disabled by the PM core. + +The difference between suspend_noirq() and suspend() is that the driver's +interrupt handler will not be invoked while suspend_noirq() is running. Thus +suspend_noirq() can carry out operations that would cause race conditions to +arise if they were performed in suspend(). + +3.1.4. freeze() +^^^^^^^^^^^^^^^ + +The freeze() callback is hibernation-specific and is executed in two situations, +during hibernation, after prepare() callbacks have been executed for all devices +in preparation for the creation of a system image, and during restore, +after a system image has been loaded into memory from persistent storage and the +prepare() callbacks have been executed for all devices. + +The role of this callback is analogous to the role of the suspend() callback +described above. In fact, they only need to be different in the rare cases when +the driver takes the responsibility for putting the device into a low-power +state. + +In that cases the freeze() callback should not prepare the device system wakeup +or put it into a low-power state. Still, either it or freeze_noirq() should +save the device's standard configuration registers using pci_save_state(). + +3.1.5. freeze_noirq() +^^^^^^^^^^^^^^^^^^^^^ + +The freeze_noirq() callback is hibernation-specific. It is executed during +hibernation, after prepare() and freeze() callbacks have been executed for all +devices in preparation for the creation of a system image, and during restore, +after a system image has been loaded into memory and after prepare() and +freeze() callbacks have been executed for all devices. It is always executed +after device interrupts have been disabled by the PM core. + +The role of this callback is analogous to the role of the suspend_noirq() +callback described above and it very rarely is necessary to define +freeze_noirq(). + +The difference between freeze_noirq() and freeze() is analogous to the +difference between suspend_noirq() and suspend(). + +3.1.6. poweroff() +^^^^^^^^^^^^^^^^^ + +The poweroff() callback is hibernation-specific. It is executed when the system +is about to be powered off after saving a hibernation image to a persistent +storage. prepare() callbacks are executed for all devices before poweroff() is +called. + +The role of this callback is analogous to the role of the suspend() and freeze() +callbacks described above, although it does not need to save the contents of +the device's registers. In particular, if the driver wants to put the device +into a low-power state itself instead of allowing the PCI subsystem to do that, +the poweroff() callback should use pci_prepare_to_sleep() and +pci_set_power_state() to prepare the device for system wakeup and to put it +into a low-power state, respectively, but it need not save the device's standard +configuration registers. + +3.1.7. poweroff_noirq() +^^^^^^^^^^^^^^^^^^^^^^^ + +The poweroff_noirq() callback is hibernation-specific. It is executed after +poweroff() callbacks have been executed for all devices in the system. + +The role of this callback is analogous to the role of the suspend_noirq() and +freeze_noirq() callbacks described above, but it does not need to save the +contents of the device's registers. + +The difference between poweroff_noirq() and poweroff() is analogous to the +difference between suspend_noirq() and suspend(). + +3.1.8. resume_noirq() +^^^^^^^^^^^^^^^^^^^^^ + +The resume_noirq() callback is only executed during system resume, after the +PM core has enabled the non-boot CPUs. The driver's interrupt handler will not +be invoked while resume_noirq() is running, so this callback can carry out +operations that might race with the interrupt handler. + +Since the PCI subsystem unconditionally puts all devices into the full power +state in the resume_noirq phase of system resume and restores their standard +configuration registers, resume_noirq() is usually not necessary. In general +it should only be used for performing operations that would lead to race +conditions if carried out by resume(). + +3.1.9. resume() +^^^^^^^^^^^^^^^ + +The resume() callback is only executed during system resume, after +resume_noirq() callbacks have been executed for all devices in the system and +device interrupts have been enabled by the PM core. + +This callback is responsible for restoring the pre-suspend configuration of the +device and bringing it back to the fully functional state. The device should be +able to process I/O in a usual way after resume() has returned. + +3.1.10. thaw_noirq() +^^^^^^^^^^^^^^^^^^^^ + +The thaw_noirq() callback is hibernation-specific. It is executed after a +system image has been created and the non-boot CPUs have been enabled by the PM +core, in the thaw_noirq phase of hibernation. It also may be executed if the +loading of a hibernation image fails during system restore (it is then executed +after enabling the non-boot CPUs). The driver's interrupt handler will not be +invoked while thaw_noirq() is running. + +The role of this callback is analogous to the role of resume_noirq(). The +difference between these two callbacks is that thaw_noirq() is executed after +freeze() and freeze_noirq(), so in general it does not need to modify the +contents of the device's registers. + +3.1.11. thaw() +^^^^^^^^^^^^^^ + +The thaw() callback is hibernation-specific. It is executed after thaw_noirq() +callbacks have been executed for all devices in the system and after device +interrupts have been enabled by the PM core. + +This callback is responsible for restoring the pre-freeze configuration of +the device, so that it will work in a usual way after thaw() has returned. + +3.1.12. restore_noirq() +^^^^^^^^^^^^^^^^^^^^^^^ + +The restore_noirq() callback is hibernation-specific. It is executed in the +restore_noirq phase of hibernation, when the boot kernel has passed control to +the image kernel and the non-boot CPUs have been enabled by the image kernel's +PM core. + +This callback is analogous to resume_noirq() with the exception that it cannot +make any assumption on the previous state of the device, even if the BIOS (or +generally the platform firmware) is known to preserve that state over a +suspend-resume cycle. + +For the vast majority of PCI device drivers there is no difference between +resume_noirq() and restore_noirq(). + +3.1.13. restore() +^^^^^^^^^^^^^^^^^ + +The restore() callback is hibernation-specific. It is executed after +restore_noirq() callbacks have been executed for all devices in the system and +after the PM core has enabled device drivers' interrupt handlers to be invoked. + +This callback is analogous to resume(), just like restore_noirq() is analogous +to resume_noirq(). Consequently, the difference between restore_noirq() and +restore() is analogous to the difference between resume_noirq() and resume(). + +For the vast majority of PCI device drivers there is no difference between +resume() and restore(). + +3.1.14. complete() +^^^^^^^^^^^^^^^^^^ + +The complete() callback is executed in the following situations: + + - during system resume, after resume() callbacks have been executed for all + devices, + - during hibernation, before saving the system image, after thaw() callbacks + have been executed for all devices, + - during system restore, when the system is going back to its pre-hibernation + state, after restore() callbacks have been executed for all devices. + +It also may be executed if the loading of a hibernation image into memory fails +(in that case it is run after thaw() callbacks have been executed for all +devices that have drivers in the boot kernel). + +This callback is entirely optional, although it may be necessary if the +prepare() callback performs operations that need to be reversed. + +3.1.15. runtime_suspend() +^^^^^^^^^^^^^^^^^^^^^^^^^ + +The runtime_suspend() callback is specific to device runtime power management +(runtime PM). It is executed by the PM core's runtime PM framework when the +device is about to be suspended (i.e. quiesced and put into a low-power state) +at run time. + +This callback is responsible for freezing the device and preparing it to be +put into a low-power state, but it must allow the PCI subsystem to perform all +of the PCI-specific actions necessary for suspending the device. + +3.1.16. runtime_resume() +^^^^^^^^^^^^^^^^^^^^^^^^ + +The runtime_resume() callback is specific to device runtime PM. It is executed +by the PM core's runtime PM framework when the device is about to be resumed +(i.e. put into the full-power state and programmed to process I/O normally) at +run time. + +This callback is responsible for restoring the normal functionality of the +device after it has been put into the full-power state by the PCI subsystem. +The device is expected to be able to process I/O in the usual way after +runtime_resume() has returned. + +3.1.17. runtime_idle() +^^^^^^^^^^^^^^^^^^^^^^ + +The runtime_idle() callback is specific to device runtime PM. It is executed +by the PM core's runtime PM framework whenever it may be desirable to suspend +the device according to the PM core's information. In particular, it is +automatically executed right after runtime_resume() has returned in case the +resume of the device has happened as a result of a spurious event. + +This callback is optional, but if it is not implemented or if it returns 0, the +PCI subsystem will call pm_runtime_suspend() for the device, which in turn will +cause the driver's runtime_suspend() callback to be executed. + +3.1.18. Pointing Multiple Callback Pointers to One Routine +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Although in principle each of the callbacks described in the previous +subsections can be defined as a separate function, it often is convenient to +point two or more members of struct dev_pm_ops to the same routine. There are +a few convenience macros that can be used for this purpose. + +The SIMPLE_DEV_PM_OPS macro declares a struct dev_pm_ops object with one +suspend routine pointed to by the .suspend(), .freeze(), and .poweroff() +members and one resume routine pointed to by the .resume(), .thaw(), and +.restore() members. The other function pointers in this struct dev_pm_ops are +unset. + +The UNIVERSAL_DEV_PM_OPS macro is similar to SIMPLE_DEV_PM_OPS, but it +additionally sets the .runtime_resume() pointer to the same value as +.resume() (and .thaw(), and .restore()) and the .runtime_suspend() pointer to +the same value as .suspend() (and .freeze() and .poweroff()). + +The SET_SYSTEM_SLEEP_PM_OPS can be used inside of a declaration of struct +dev_pm_ops to indicate that one suspend routine is to be pointed to by the +.suspend(), .freeze(), and .poweroff() members and one resume routine is to +be pointed to by the .resume(), .thaw(), and .restore() members. + +3.1.19. Driver Flags for Power Management +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +The PM core allows device drivers to set flags that influence the handling of +power management for the devices by the core itself and by middle layer code +including the PCI bus type. The flags should be set once at the driver probe +time with the help of the dev_pm_set_driver_flags() function and they should not +be updated directly afterwards. + +The DPM_FLAG_NO_DIRECT_COMPLETE flag prevents the PM core from using the +direct-complete mechanism allowing device suspend/resume callbacks to be skipped +if the device is in runtime suspend when the system suspend starts. That also +affects all of the ancestors of the device, so this flag should only be used if +absolutely necessary. + +The DPM_FLAG_SMART_PREPARE flag causes the PCI bus type to return a positive +value from pci_pm_prepare() only if the ->prepare callback provided by the +driver of the device returns a positive value. That allows the driver to opt +out from using the direct-complete mechanism dynamically (whereas setting +DPM_FLAG_NO_DIRECT_COMPLETE means permanent opt-out). + +The DPM_FLAG_SMART_SUSPEND flag tells the PCI bus type that from the driver's +perspective the device can be safely left in runtime suspend during system +suspend. That causes pci_pm_suspend(), pci_pm_freeze() and pci_pm_poweroff() +to avoid resuming the device from runtime suspend unless there are PCI-specific +reasons for doing that. Also, it causes pci_pm_suspend_late/noirq() and +pci_pm_poweroff_late/noirq() to return early if the device remains in runtime +suspend during the "late" phase of the system-wide transition under way. +Moreover, if the device is in runtime suspend in pci_pm_resume_noirq() or +pci_pm_restore_noirq(), its runtime PM status will be changed to "active" (as it +is going to be put into D0 going forward). + +Setting the DPM_FLAG_MAY_SKIP_RESUME flag means that the driver allows its +"noirq" and "early" resume callbacks to be skipped if the device can be left +in suspend after a system-wide transition into the working state. This flag is +taken into consideration by the PM core along with the power.may_skip_resume +status bit of the device which is set by pci_pm_suspend_noirq() in certain +situations. If the PM core determines that the driver's "noirq" and "early" +resume callbacks should be skipped, the dev_pm_skip_resume() helper function +will return "true" and that will cause pci_pm_resume_noirq() and +pci_pm_resume_early() to return upfront without touching the device and +executing the driver callbacks. + +3.2. Device Runtime Power Management +------------------------------------ + +In addition to providing device power management callbacks PCI device drivers +are responsible for controlling the runtime power management (runtime PM) of +their devices. + +The PCI device runtime PM is optional, but it is recommended that PCI device +drivers implement it at least in the cases where there is a reliable way of +verifying that the device is not used (like when the network cable is detached +from an Ethernet adapter or there are no devices attached to a USB controller). + +To support the PCI runtime PM the driver first needs to implement the +runtime_suspend() and runtime_resume() callbacks. It also may need to implement +the runtime_idle() callback to prevent the device from being suspended again +every time right after the runtime_resume() callback has returned +(alternatively, the runtime_suspend() callback will have to check if the +device should really be suspended and return -EAGAIN if that is not the case). + +The runtime PM of PCI devices is enabled by default by the PCI core. PCI +device drivers do not need to enable it and should not attempt to do so. +However, it is blocked by pci_pm_init() that runs the pm_runtime_forbid() +helper function. In addition to that, the runtime PM usage counter of +each PCI device is incremented by local_pci_probe() before executing the +probe callback provided by the device's driver. + +If a PCI driver implements the runtime PM callbacks and intends to use the +runtime PM framework provided by the PM core and the PCI subsystem, it needs +to decrement the device's runtime PM usage counter in its probe callback +function. If it doesn't do that, the counter will always be different from +zero for the device and it will never be runtime-suspended. The simplest +way to do that is by calling pm_runtime_put_noidle(), but if the driver +wants to schedule an autosuspend right away, for example, it may call +pm_runtime_put_autosuspend() instead for this purpose. Generally, it +just needs to call a function that decrements the devices usage counter +from its probe routine to make runtime PM work for the device. + +It is important to remember that the driver's runtime_suspend() callback +may be executed right after the usage counter has been decremented, because +user space may already have caused the pm_runtime_allow() helper function +unblocking the runtime PM of the device to run via sysfs, so the driver must +be prepared to cope with that. + +The driver itself should not call pm_runtime_allow(), though. Instead, it +should let user space or some platform-specific code do that (user space can +do it via sysfs as stated above), but it must be prepared to handle the +runtime PM of the device correctly as soon as pm_runtime_allow() is called +(which may happen at any time, even before the driver is loaded). + +When the driver's remove callback runs, it has to balance the decrementation +of the device's runtime PM usage counter at the probe time. For this reason, +if it has decremented the counter in its probe callback, it must run +pm_runtime_get_noresume() in its remove callback. [Since the core carries +out a runtime resume of the device and bumps up the device's usage counter +before running the driver's remove callback, the runtime PM of the device +is effectively disabled for the duration of the remove execution and all +runtime PM helper functions incrementing the device's usage counter are +then effectively equivalent to pm_runtime_get_noresume().] + +The runtime PM framework works by processing requests to suspend or resume +devices, or to check if they are idle (in which cases it is reasonable to +subsequently request that they be suspended). These requests are represented +by work items put into the power management workqueue, pm_wq. Although there +are a few situations in which power management requests are automatically +queued by the PM core (for example, after processing a request to resume a +device the PM core automatically queues a request to check if the device is +idle), device drivers are generally responsible for queuing power management +requests for their devices. For this purpose they should use the runtime PM +helper functions provided by the PM core, discussed in +Documentation/power/runtime_pm.rst. + +Devices can also be suspended and resumed synchronously, without placing a +request into pm_wq. In the majority of cases this also is done by their +drivers that use helper functions provided by the PM core for this purpose. + +For more information on the runtime PM of devices refer to +Documentation/power/runtime_pm.rst. + + +4. Resources +============ + +PCI Local Bus Specification, Rev. 3.0 + +PCI Bus Power Management Interface Specification, Rev. 1.2 + +Advanced Configuration and Power Interface (ACPI) Specification, Rev. 3.0b + +PCI Express Base Specification, Rev. 2.0 + +Documentation/driver-api/pm/devices.rst + +Documentation/power/runtime_pm.rst |