diff options
Diffstat (limited to 'Documentation/userspace-api/media/v4l')
7 files changed, 132 insertions, 29 deletions
diff --git a/Documentation/userspace-api/media/v4l/buffer.rst b/Documentation/userspace-api/media/v4l/buffer.rst index 04dec3e57..52bbee81c 100644 --- a/Documentation/userspace-api/media/v4l/buffer.rst +++ b/Documentation/userspace-api/media/v4l/buffer.rst @@ -549,9 +549,9 @@ Buffer Flags - 0x00000400 - The buffer has been prepared for I/O and can be queued by the application. Drivers set or clear this flag when the - :ref:`VIDIOC_QUERYBUF`, + :ref:`VIDIOC_QUERYBUF <VIDIOC_QUERYBUF>`, :ref:`VIDIOC_PREPARE_BUF <VIDIOC_QBUF>`, - :ref:`VIDIOC_QBUF` or + :ref:`VIDIOC_QBUF <VIDIOC_QBUF>` or :ref:`VIDIOC_DQBUF <VIDIOC_QBUF>` ioctl is called. * .. _`V4L2-BUF-FLAG-NO-CACHE-INVALIDATE`: diff --git a/Documentation/userspace-api/media/v4l/control.rst b/Documentation/userspace-api/media/v4l/control.rst index 4463fce69..57893814a 100644 --- a/Documentation/userspace-api/media/v4l/control.rst +++ b/Documentation/userspace-api/media/v4l/control.rst @@ -143,9 +143,13 @@ Control IDs recognise the difference between digital and analogue gain use controls ``V4L2_CID_DIGITAL_GAIN`` and ``V4L2_CID_ANALOGUE_GAIN``. +.. _v4l2-cid-hflip: + ``V4L2_CID_HFLIP`` ``(boolean)`` Mirror the picture horizontally. +.. _v4l2-cid-vflip: + ``V4L2_CID_VFLIP`` ``(boolean)`` Mirror the picture vertically. diff --git a/Documentation/userspace-api/media/v4l/dev-subdev.rst b/Documentation/userspace-api/media/v4l/dev-subdev.rst index a4f1df709..43988516a 100644 --- a/Documentation/userspace-api/media/v4l/dev-subdev.rst +++ b/Documentation/userspace-api/media/v4l/dev-subdev.rst @@ -579,20 +579,19 @@ is started. There are three steps in configuring the streams: -1) Set up links. Connect the pads between sub-devices using the :ref:`Media -Controller API <media_controller>` +1. Set up links. Connect the pads between sub-devices using the + :ref:`Media Controller API <media_controller>` -2) Streams. Streams are declared and their routing is configured by -setting the routing table for the sub-device using -:ref:`VIDIOC_SUBDEV_S_ROUTING <VIDIOC_SUBDEV_G_ROUTING>` ioctl. Note that -setting the routing table will reset formats and selections in the -sub-device to default values. +2. Streams. Streams are declared and their routing is configured by setting the + routing table for the sub-device using :ref:`VIDIOC_SUBDEV_S_ROUTING + <VIDIOC_SUBDEV_G_ROUTING>` ioctl. Note that setting the routing table will + reset formats and selections in the sub-device to default values. -3) Configure formats and selections. Formats and selections of each stream -are configured separately as documented for plain sub-devices in -:ref:`format-propagation`. The stream ID is set to the same stream ID -associated with either sink or source pads of routes configured using the -:ref:`VIDIOC_SUBDEV_S_ROUTING <VIDIOC_SUBDEV_G_ROUTING>` ioctl. +3. Configure formats and selections. Formats and selections of each stream are + configured separately as documented for plain sub-devices in + :ref:`format-propagation`. The stream ID is set to the same stream ID + associated with either sink or source pads of routes configured using the + :ref:`VIDIOC_SUBDEV_S_ROUTING <VIDIOC_SUBDEV_G_ROUTING>` ioctl. Multiplexed streams setup example ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ @@ -618,11 +617,11 @@ modeled as V4L2 devices, exposed to userspace via /dev/videoX nodes. To configure this pipeline, the userspace must take the following steps: -1) Set up media links between entities: connect the sensors to the bridge, -bridge to the receiver, and the receiver to the DMA engines. This step does -not differ from normal non-multiplexed media controller setup. +1. Set up media links between entities: connect the sensors to the bridge, + bridge to the receiver, and the receiver to the DMA engines. This step does + not differ from normal non-multiplexed media controller setup. -2) Configure routing +2. Configure routing .. flat-table:: Bridge routing table :header-rows: 1 @@ -656,14 +655,14 @@ not differ from normal non-multiplexed media controller setup. - V4L2_SUBDEV_ROUTE_FL_ACTIVE - Pixel data stream from Sensor B -3) Configure formats and selections +3. Configure formats and selections -After configuring routing, the next step is configuring the formats and -selections for the streams. This is similar to performing this step without -streams, with just one exception: the ``stream`` field needs to be assigned -to the value of the stream ID. + After configuring routing, the next step is configuring the formats and + selections for the streams. This is similar to performing this step without + streams, with just one exception: the ``stream`` field needs to be assigned + to the value of the stream ID. -A common way to accomplish this is to start from the sensors and propagate the -configurations along the stream towards the receiver, -using :ref:`VIDIOC_SUBDEV_S_FMT <VIDIOC_SUBDEV_G_FMT>` ioctls to configure each -stream endpoint in each sub-device. + A common way to accomplish this is to start from the sensors and propagate + the configurations along the stream towards the receiver, using + :ref:`VIDIOC_SUBDEV_S_FMT <VIDIOC_SUBDEV_G_FMT>` ioctls to configure each + stream endpoint in each sub-device. diff --git a/Documentation/userspace-api/media/v4l/dv-timings.rst b/Documentation/userspace-api/media/v4l/dv-timings.rst index e17f056b1..4b19bcb4b 100644 --- a/Documentation/userspace-api/media/v4l/dv-timings.rst +++ b/Documentation/userspace-api/media/v4l/dv-timings.rst @@ -33,6 +33,27 @@ current DV timings they use the the DV timings as seen by the video receiver applications use the :ref:`VIDIOC_QUERY_DV_TIMINGS` ioctl. +When the hardware detects a video source change (e.g. the video +signal appears or disappears, or the video resolution changes), then +it will issue a `V4L2_EVENT_SOURCE_CHANGE` event. Use the +:ref:`ioctl VIDIOC_SUBSCRIBE_EVENT <VIDIOC_SUBSCRIBE_EVENT>` and the +:ref:`VIDIOC_DQEVENT` to check if this event was reported. + +If the video signal changed, then the application has to stop +streaming, free all buffers, and call the :ref:`VIDIOC_QUERY_DV_TIMINGS` +to obtain the new video timings, and if they are valid, it can set +those by calling the :ref:`ioctl VIDIOC_S_DV_TIMINGS <VIDIOC_G_DV_TIMINGS>`. +This will also update the format, so use the :ref:`ioctl VIDIOC_G_FMT <VIDIOC_G_FMT>` +to obtain the new format. Now the application can allocate new buffers +and start streaming again. + +The :ref:`VIDIOC_QUERY_DV_TIMINGS` will just report what the +hardware detects, it will never change the configuration. If the +currently set timings and the actually detected timings differ, then +typically this will mean that you will not be able to capture any +video. The correct approach is to rely on the `V4L2_EVENT_SOURCE_CHANGE` +event so you know when something changed. + Applications can make use of the :ref:`input-capabilities` and :ref:`output-capabilities` flags to determine whether the digital video ioctls can be used with the given input or output. diff --git a/Documentation/userspace-api/media/v4l/pixfmt-reserved.rst b/Documentation/userspace-api/media/v4l/pixfmt-reserved.rst index 296ad2025..886ba7b08 100644 --- a/Documentation/userspace-api/media/v4l/pixfmt-reserved.rst +++ b/Documentation/userspace-api/media/v4l/pixfmt-reserved.rst @@ -288,6 +288,13 @@ please make a proposal on the linux-media mailing list. - 'MT2110R' - This format is two-planar 10-Bit raster mode and having similitude with ``V4L2_PIX_FMT_MM21`` in term of alignment and tiling. Used for AVC. + * .. _V4L2-PIX-FMT-HEXTILE: + + - ``V4L2_PIX_FMT_HEXTILE`` + - 'HXTL' + - Compressed format used by Nuvoton NPCM video driver. This format is + defined in Remote Framebuffer Protocol (RFC 6143, chapter 7.7.4 Hextile + Encoding). .. raw:: latex \normalsize diff --git a/Documentation/userspace-api/media/v4l/pixfmt-srggb12p.rst b/Documentation/userspace-api/media/v4l/pixfmt-srggb12p.rst index b6e79e2f8..7c3810ff7 100644 --- a/Documentation/userspace-api/media/v4l/pixfmt-srggb12p.rst +++ b/Documentation/userspace-api/media/v4l/pixfmt-srggb12p.rst @@ -60,7 +60,7 @@ Each cell is one byte. G\ :sub:`10low`\ (bits 3--0) - G\ :sub:`12high` - R\ :sub:`13high` - - R\ :sub:`13low`\ (bits 3--2) + - R\ :sub:`13low`\ (bits 7--4) G\ :sub:`12low`\ (bits 3--0) - - start + 12: @@ -82,6 +82,6 @@ Each cell is one byte. G\ :sub:`30low`\ (bits 3--0) - G\ :sub:`32high` - R\ :sub:`33high` - - R\ :sub:`33low`\ (bits 3--2) + - R\ :sub:`33low`\ (bits 7--4) G\ :sub:`32low`\ (bits 3--0) diff --git a/Documentation/userspace-api/media/v4l/subdev-formats.rst b/Documentation/userspace-api/media/v4l/subdev-formats.rst index a3a35eeed..eb3cd20b0 100644 --- a/Documentation/userspace-api/media/v4l/subdev-formats.rst +++ b/Documentation/userspace-api/media/v4l/subdev-formats.rst @@ -949,6 +949,78 @@ The following tables list existing packed RGB formats. - b\ :sub:`2` - b\ :sub:`1` - b\ :sub:`0` + * .. _MEDIA-BUS-FMT-RGB666-2X9-BE: + + - MEDIA_BUS_FMT_RGB666_2X9_BE + - 0x1025 + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - r\ :sub:`5` + - r\ :sub:`4` + - r\ :sub:`3` + - r\ :sub:`2` + - r\ :sub:`1` + - r\ :sub:`0` + - g\ :sub:`5` + - g\ :sub:`4` + - g\ :sub:`3` + * - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - + - g\ :sub:`2` + - g\ :sub:`1` + - g\ :sub:`0` + - b\ :sub:`5` + - b\ :sub:`4` + - b\ :sub:`3` + - b\ :sub:`2` + - b\ :sub:`1` + - b\ :sub:`0` * .. _MEDIA-BUS-FMT-BGR666-1X18: - MEDIA_BUS_FMT_BGR666_1X18 |