diff options
Diffstat (limited to 'arch/arm/boot/dts/amlogic/meson8b-odroidc1.dts')
-rw-r--r-- | arch/arm/boot/dts/amlogic/meson8b-odroidc1.dts | 383 |
1 files changed, 383 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/amlogic/meson8b-odroidc1.dts b/arch/arm/boot/dts/amlogic/meson8b-odroidc1.dts new file mode 100644 index 0000000000..941682844f --- /dev/null +++ b/arch/arm/boot/dts/amlogic/meson8b-odroidc1.dts @@ -0,0 +1,383 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright 2015 Endless Mobile, Inc. + * Author: Carlo Caione <carlo@endlessm.com> + */ + +/dts-v1/; +#include "meson8b.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Hardkernel ODROID-C1"; + compatible = "hardkernel,odroid-c1", "amlogic,meson8b"; + + aliases { + serial0 = &uart_AO; + mmc0 = &sd_card_slot; + mmc1 = &sdhc; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + device_type = "memory"; + reg = <0x40000000 0x40000000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; + }; + + leds { + compatible = "gpio-leds"; + led-blue { + label = "c1:blue:alive"; + gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + }; + + p5v0: regulator-p5v0 { + compatible = "regulator-fixed"; + + regulator-name = "P5V0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + tflash_vdd: regulator-tflash_vdd { + /* + * signal name from schematics: TFLASH_VDD_EN + */ + compatible = "regulator-fixed"; + + regulator-name = "TFLASH_VDD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + vin-supply = <&vcc_3v3>; + + gpio = <&gpio GPIOY_12 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + tf_io: gpio-regulator-tf_io { + compatible = "regulator-gpio"; + + regulator-name = "TF_IO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + vin-supply = <&vcc_3v3>; + + /* + * signal name from schematics: TF_3V3N_1V8_EN + */ + gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + + states = <3300000 0 + 1800000 1>; + }; + + rtc32k_xtal: rtc32k-xtal-clk { + /* X3 in the schematics */ + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "RTC32K"; + #clock-cells = <0>; + }; + + vcc_1v8: regulator-vcc-1v8 { + /* + * RICHTEK RT9179 configured for a fixed output voltage of + * 1.8V. This supplies not only VCC1V8 but also IOREF_1V8 and + * VDD1V8 according to the schematics. + */ + compatible = "regulator-fixed"; + + regulator-name = "VCC1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + vin-supply = <&p5v0>; + }; + + vcc_3v3: regulator-vcc-3v3 { + /* + * Monolithic Power Systems MP2161 configured for a fixed + * output voltage of 3.3V. This supplies not only VCC3V3 but + * also VDD3V3 and VDDIO_AO3V3 according to the schematics. + */ + compatible = "regulator-fixed"; + + regulator-name = "VCC3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + vin-supply = <&p5v0>; + }; + + vcck: regulator-vcck { + /* Monolithic Power Systems MP2161 */ + compatible = "pwm-regulator"; + + regulator-name = "VCCK"; + regulator-min-microvolt = <860000>; + regulator-max-microvolt = <1140000>; + + pwm-supply = <&p5v0>; + + pwms = <&pwm_cd 0 12218 0>; + pwm-dutycycle-range = <91 0>; + + regulator-boot-on; + regulator-always-on; + }; + + vddc_ddr: regulator-vddc-ddr { + /* + * Monolithic Power Systems MP2161 configured for a fixed + * output voltage of 1.5V. This supplies not only DDR_VDDC but + * also DDR3_1V5 according to the schematics. + */ + compatible = "regulator-fixed"; + + regulator-name = "DDR_VDDC"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + + vin-supply = <&p5v0>; + }; + + vddee: regulator-vddee { + /* Monolithic Power Systems MP2161 */ + compatible = "pwm-regulator"; + + regulator-name = "VDDEE"; + regulator-min-microvolt = <860000>; + regulator-max-microvolt = <1140000>; + + pwm-supply = <&p5v0>; + + pwms = <&pwm_cd 1 12218 0>; + pwm-dutycycle-range = <91 0>; + + regulator-boot-on; + regulator-always-on; + }; + + vdd_rtc: regulator-vdd-rtc { + /* + * Torex Semiconductor XC6215 configured for a fixed output of + * 0.9V. + */ + compatible = "regulator-fixed"; + + regulator-name = "VDD_RTC"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + vin-supply = <&vcc_3v3>; + }; +}; + +&cpu0 { + cpu-supply = <&vcck>; +}; + +&efuse { + ethernet_mac_address: mac@1b4 { + reg = <0x1b4 0x6>; + }; +}; + +ðmac { + status = "okay"; + + pinctrl-0 = <ð_rgmii_pins>; + pinctrl-names = "default"; + + phy-handle = <ð_phy>; + phy-mode = "rgmii-id"; + + nvmem-cells = <ðernet_mac_address>; + nvmem-cell-names = "mac-address"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + /* Realtek RTL8211F (0x001cc916) */ + eth_phy: ethernet-phy@0 { + reg = <0>; + + reset-assert-us = <10000>; + reset-deassert-us = <80000>; + reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>; + + interrupt-parent = <&gpio_intc>; + /* GPIOH_3 */ + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + }; + }; +}; + +&gpio { + gpio-line-names = /* Bank GPIOX */ + "J2 Header Pin 35", "J2 Header Pin 36", + "J2 Header Pin 32", "J2 Header Pin 31", + "J2 Header Pin 29", "J2 Header Pin 18", + "J2 Header Pin 22", "J2 Header Pin 16", + "J2 Header Pin 23", "J2 Header Pin 21", + "J2 Header Pin 19", "J2 Header Pin 33", + "J2 Header Pin 8", "J2 Header Pin 10", + "J2 Header Pin 15", "J2 Header Pin 13", + "J2 Header Pin 24", "J2 Header Pin 26", + /* Bank GPIOY */ + "Revision (upper)", "Revision (lower)", + "J2 Header Pin 7", "", "J2 Header Pin 12", + "J2 Header Pin 11", "", "", "", + "TFLASH_VDD_EN", "", "", + /* Bank GPIODV */ + "VCCK_PWM (PWM_C)", "I2CA_SDA", "I2CA_SCL", + "I2CB_SDA", "I2CB_SCL", "VDDEE_PWM (PWM_D)", + "", + /* Bank GPIOH */ + "HDMI_HPD", "HDMI_I2C_SDA", "HDMI_I2C_SCL", + "ETH_PHY_INTR", "ETH_PHY_NRST", "ETH_TXD1", + "ETH_TXD0", "ETH_TXD3", "ETH_TXD2", + "ETH_RGMII_TX_CLK", + /* Bank CARD */ + "SD_DATA1 (SDB_D1)", "SD_DATA0 (SDB_D0)", + "SD_CLK", "SD_CMD", "SD_DATA3 (SDB_D3)", + "SD_DATA2 (SDB_D2)", "SD_CDN (SD_DET_N)", + /* Bank BOOT */ + "SDC_D0 (EMMC)", "SDC_D1 (EMMC)", + "SDC_D2 (EMMC)", "SDC_D3 (EMMC)", + "SDC_D4 (EMMC)", "SDC_D5 (EMMC)", + "SDC_D6 (EMMC)", "SDC_D7 (EMMC)", + "SDC_CLK (EMMC)", "SDC_RSTn (EMMC)", + "SDC_CMD (EMMC)", "BOOT_SEL", "", "", "", + "", "", "", "", + /* Bank DIF */ + "ETH_RXD1", "ETH_RXD0", "ETH_RX_DV", + "RGMII_RX_CLK", "ETH_RXD3", "ETH_RXD2", + "ETH_TXEN", "ETH_PHY_REF_CLK_25MOUT", + "ETH_MDC", "ETH_MDIO"; +}; + +&gpio_ao { + gpio-line-names = "UART TX", "UART RX", "", + "TF_3V3N_1V8_EN", "USB_HUB_RST_N", + "USB_OTG_PWREN", "J7 Header Pin 2", + "IR_IN", "J7 Header Pin 4", + "J7 Header Pin 6", "J7 Header Pin 5", + "J7 Header Pin 7", "HDMI_CEC", + "SYS_LED", "", ""; +}; + +&ir_receiver { + status = "okay"; + pinctrl-0 = <&ir_recv_pins>; + pinctrl-names = "default"; +}; + +&mali { + mali-supply = <&vddee>; +}; + +&saradc { + status = "okay"; + vref-supply = <&vcc_1v8>; +}; + +&sdhc { + status = "okay"; + + pinctrl-0 = <&sdxc_c_pins>; + pinctrl-names = "default"; + + bus-width = <8>; + max-frequency = <100000000>; + + disable-wp; + cap-mmc-highspeed; + mmc-hs200-1_8v; + no-sdio; + + mmc-pwrseq = <&emmc_pwrseq>; + + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vcc_1v8>; +}; + +&sdio { + status = "okay"; + + pinctrl-0 = <&sd_b_pins>; + pinctrl-names = "default"; + + /* SD card */ + sd_card_slot: slot@1 { + compatible = "mmc-slot"; + reg = <1>; + status = "okay"; + + bus-width = <4>; + no-sdio; + cap-mmc-highspeed; + cap-sd-highspeed; + disable-wp; + + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>; + + vmmc-supply = <&tflash_vdd>; + vqmmc-supply = <&tf_io>; + }; +}; + +&pwm_cd { + status = "okay"; + pinctrl-0 = <&pwm_c1_pins>, <&pwm_d_pins>; + pinctrl-names = "default"; + clocks = <&xtal>, <&xtal>; + clock-names = "clkin0", "clkin1"; +}; + +&rtc { + /* needs to be enabled manually when a battery is connected */ + clocks = <&rtc32k_xtal>; + vdd-supply = <&vdd_rtc>; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb1 { + dr_mode = "host"; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + hub@1 { + /* Genesys Logic GL852G usb hub */ + compatible = "usb5e3,610"; + reg = <1>; + vdd-supply = <&p5v0>; + reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>; + }; +}; |