diff options
Diffstat (limited to 'arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s8036.dts')
-rw-r--r-- | arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s8036.dts | 471 |
1 files changed, 471 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s8036.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s8036.dts new file mode 100644 index 0000000000..f6c4549c0a --- /dev/null +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s8036.dts @@ -0,0 +1,471 @@ +// SPDX-License-Identifier: GPL-2.0+ +/dts-v1/; + +#include "aspeed-g5.dtsi" +#include <dt-bindings/gpio/aspeed-gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + model = "Tyan S8036 BMC"; + compatible = "tyan,s8036-bmc", "aspeed,ast2500"; + + chosen { + stdout-path = &uart5; + bootargs = "console=ttyS4,115200 earlycon"; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x20000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + p2a_memory: region@987f0000 { + no-map; + reg = <0x987f0000 0x00010000>; /* 64KB */ + }; + + vga_memory: framebuffer@9f000000 { + no-map; + reg = <0x9f000000 0x01000000>; /* 16M */ + }; + + gfx_memory: framebuffer { + size = <0x01000000>; /* 16M */ + alignment = <0x01000000>; + compatible = "shared-dma-pool"; + reusable; + }; + }; + + leds { + compatible = "gpio-leds"; + + identify { + gpios = <&gpio ASPEED_GPIO(A, 2) GPIO_ACTIVE_LOW>; + }; + + heartbeat { + gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>; + }; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, + <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>, + <&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>, + <&adc 12>, <&adc 13>, <&adc 14>; + }; + + iio-hwmon-battery { + compatible = "iio-hwmon"; + io-channels = <&adc 15>; + }; +}; + +&fmc { + status = "okay"; + flash@0 { + label = "bmc"; + status = "okay"; + m25p,fast-read; +#include "openbmc-flash-layout.dtsi" + }; +}; + +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1_default>; + + flash@0 { + status = "okay"; + label = "pnor"; + m25p,fast-read; + }; +}; + +&uart1 { + /* Rear RS-232 connector */ + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd1_default + &pinctrl_rxd1_default>; +}; + +&uart2 { + /* RS-232 connector on header */ + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd2_default + &pinctrl_rxd2_default>; +}; + +&uart3 { + /* Alternative to vuart to internally connect (route) to uart1 + * when vuart cannot be used due to BIOS limitations. + */ + status = "okay"; +}; + +&uart4 { + /* Alternative to vuart to internally connect (route) to the + * external port usually used by uart1 when vuart cannot be + * used due to BIOS limitations. + */ + status = "okay"; +}; + +&uart5 { + /* BMC "debug" (console) UART; connected to RS-232 connector + * on header; selectable via jumpers as alternative to uart2 + */ + status = "okay"; +}; + +&uart_routing { + status = "okay"; +}; + +&vuart { + status = "okay"; + + /* We enable the VUART here, but leave it in a state that does + * not interfere with the SuperIO. The goal is to have both the + * VUART and the SuperIO available and decide at runtime whether + * the VUART should actually be used. For that reason, configure + * an "invalid" IO address and an IRQ that is not used by the + * BMC. + */ + aspeed,lpc-io-reg = <0xffff>; + aspeed,lpc-interrupts = <15 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lpc_ctrl { + status = "okay"; +}; + +&p2a { + status = "okay"; + memory-region = <&p2a_memory>; +}; + +&lpc_snoop { + status = "okay"; + snoop-ports = <0x80>; +}; + +&adc { + status = "okay"; +}; + +&vhub { + status = "okay"; +}; + +&pwm_tacho { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_default + &pinctrl_pwm1_default + &pinctrl_pwm3_default + &pinctrl_pwm4_default>; + + /* CPU fan */ + fan@0 { + reg = <0x00>; + aspeed,fan-tach-ch = /bits/ 8 <0x00>; + }; + + /* PWM group for chassis fans #1, #2, #3 and #4 */ + fan@2 { + reg = <0x03>; + aspeed,fan-tach-ch = /bits/ 8 <0x02>; + }; + + fan@3 { + reg = <0x03>; + aspeed,fan-tach-ch = /bits/ 8 <0x03>; + }; + + fan@4 { + reg = <0x03>; + aspeed,fan-tach-ch = /bits/ 8 <0x04>; + }; + + fan@5 { + reg = <0x03>; + aspeed,fan-tach-ch = /bits/ 8 <0x05>; + }; + + /* PWM group for chassis fans #5 and #6 */ + fan@6 { + reg = <0x04>; + aspeed,fan-tach-ch = /bits/ 8 <0x06>; + }; + + fan@7 { + reg = <0x04>; + aspeed,fan-tach-ch = /bits/ 8 <0x07>; + }; +}; + +&i2c0 { + /* Directly connected to Sideband-Temperature Sensor Interface (APML) */ + status = "okay"; +}; + +&i2c1 { + /* Directly connected to IPMB HDR. */ + status = "okay"; +}; + +&i2c2 { + status = "okay"; + + /* BMC EEPROM, incl. mainboard FRU */ + eeprom@50 { + compatible = "atmel,24c256"; + reg = <0x50>; + }; + /* Also connected to: + * - BCM5720 + * - FPGA + * - FAN HDR + * - FPIO HDR + */ +}; + +&i2c3 { + status = "okay"; + + /* PSU1 FRU @ 0xA0 */ + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; + + /* PSU2 FRU @ 0xA2 */ + eeprom@51 { + compatible = "atmel,24c02"; + reg = <0x51>; + }; + + /* PSU1 @ 0xB0 */ + power-supply@58 { + compatible = "pmbus"; + reg = <0x58>; + }; + + /* PSU2 @ 0xB2 */ + power-supply@59 { + compatible = "pmbus"; + reg = <0x59>; + }; + +}; + +&i2c4 { + status = "okay"; +}; + +&i2c5 { + status = "okay"; + /* Hardware monitor with temperature sensors */ + nct7802@28 { + compatible = "nuvoton,nct7802"; + reg = <0x28>; + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { /* LTD */ + reg = <0>; + status = "okay"; + }; + + channel@1 { /* RTD1 */ + reg = <1>; + status = "okay"; + sensor-type = "temperature"; + temperature-mode = "thermistor"; + }; + + channel@2 { /* RTD2 */ + reg = <2>; + status = "okay"; + sensor-type = "temperature"; + temperature-mode = "thermistor"; + }; + + channel@3 { /* RTD3 */ + reg = <3>; + status = "okay"; + sensor-type = "temperature"; + }; + }; + + /* Also connected to: + * - PCA9544 + * - CLK BUFF + * - OCP FRU + */ +}; + +&i2c6 { + status = "okay"; + /* Connected to: + * - PCA9548 @0xE0 + * - PCA9548 @0xE2 + * - PCA9544 @0xE4 + */ +}; + +&i2c7 { + status = "okay"; + + /* Connected to: + * - PCH SMBUS #4 + */ +}; + +&i2c8 { + status = "okay"; + + /* Not connected */ +}; + +&mac0 { + status = "okay"; + use-ncsi; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii1_default>; +}; + +&mac1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>; +}; + +&ibt { + status = "okay"; +}; + +&kcs1 { + status = "okay"; + aspeed,lpc-io-reg = <0xca8>; +}; + +&kcs3 { + status = "okay"; + aspeed,lpc-io-reg = <0xca2>; + aspeed,lpc-interrupts = <1 IRQ_TYPE_LEVEL_HIGH>; +}; + +/* Enable BMC VGA output to show an early (pre-BIOS) boot screen */ +&gfx { + status = "okay"; + memory-region = <&gfx_memory>; +}; + +/* We're following the GPIO naming as defined at + * https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md. + * + * Notes on led-identify and id-button: + * - A physical button is connected to id-button which + * triggers the clock on a D flip-flop. The /Q output of the + * flip-flop drives its D input. + * - The flip-flop's Q output drives led-identify which is + * connected to LEDs. + * - With that, every button press toggles the LED between on and off. + * + * Notes on power-, reset- and nmi- button and control: + * - The -button signals can be used to monitor physical buttons. + * - The -control signals can be used to actuate the specific + * operation. + * - In hardware, the -button signals are connected to the -control + * signals through drivers with the -control signals being + * protected through diodes. + */ +&gpio { + status = "okay"; + gpio-line-names = + /*A0*/ "", + /*A1*/ "", + /*A2*/ "led-identify", /* in/out: BMC_CHASSIS_ID_LED_L */ + /*A3*/ "", + /*A4*/ "", + /*A5*/ "", + /*A6*/ "", + /*A7*/ "", + /*B0-B7*/ "","","","","","","","", + /*C0-C7*/ "","","","","","","","", + /*D0*/ "", + /*D1*/ "", + /*D2*/ "power-chassis-good", /* in: PWR_GOOD_LED -- Check if this is Z3?*/ + /*D3*/ "platform-reset", /* in: RESET_LED_L */ + /*D4*/ "", + /*D5*/ "", + /*D6*/ "", + /*D7*/ "", + /*E0*/ "power-button", /* in: BMC_SYS_MON_PWR_BTN_L */ + /*E1*/ "power-chassis-control", /* out: BMC_ASSERT_PWR_BTN */ + /*E2*/ "reset-button", /* in: BMC_SYS_MOS_RST_BTN_L*/ + /*E3*/ "reset-control", /* out: BMC_ASSERT_RST_BTN */ + /*E4*/ "nmi-button", /* in: BMC_SYS_MON_NMI_BTN_L */ + /*E5*/ "nmi-control", /* out: BMC_ASSERT_NMI_BTN */ + /*E6*/ "TSI_RESERT", + /*E7*/ "led-heartbeat", /* out: BMC_GPIOE7 */ + /*F0*/ "", + /*F1*/ "clear-cmos-control", /* out: BMC_ASSERT_CLR_CMOS_L */ + /*F2*/ "", + /*F3*/ "", + /*F4*/ "led-fault", /* out: BMC_HWM_FAULT_LED_L */ + /*F5*/ "BMC_SYS_FAULT_LED_L", + /*F6*/ "BMC_ASSERT_BIOS_WP_L", + /*F7*/ "", + /*G0-G7*/ "","","","","","","","", + /*H0-H7*/ "","","","","","","","", + /*I0-I7*/ "","","","","","","","", + /*J0-J7*/ "","","","","","","","", + /*K0-K7*/ "","","","","","","","", + /*L0-L7*/ "","","","","","","","", + /*M0-M7*/ "","","","","","","","", + /*N0-N7*/ "","","","","","","","", + /*O0-O7*/ "","","","","","","","", + /*P0-P7*/ "","","","","","","","", + /*Q0*/ "", + /*Q1*/ "", + /*Q2*/ "", + /*Q3*/ "", + /*Q4*/ "", + /*Q5*/ "", + /*Q6*/ "id-button", /* in: BMC_CHASSIS_ID_BTN_L */ + /*Q7*/ "", + /*R0-R7*/ "","","","","","","","", + /*S0-S7*/ "","","","","","","","", + /*T0-T7*/ "","","","","","","","", + /*U0-U7*/ "","","","","","","","", + /*V0-V7*/ "","","","","","","","", + /*W0-W7*/ "","","","","","","","", + /*X0-X7*/ "","","","","","","","", + /*Y0-Y7*/ "","","","","","","","", + /*Z0-Z2*/ "","","", + /*Z3*/ "post-complete", /* BMC_SYS_MON_PWROK */ + /*Z4-Z7*/ "","","","", + /*AA0*/ "", + /*AA1*/ "", + /*AA2*/ "", + /*AA3*/ "", + /*AA4*/ "", + /*AA5*/ "", + /*AA6*/ "", + /*AA7*/ "BMC_ASSERT_BMC_READY", + /*AB0*/ "BMC_SPD_SEL", + /*AB1-AB7*/ "","","","","","",""; +}; |