diff options
Diffstat (limited to 'arch/arm/boot/dts/marvell/orion5x-maxtor-shared-storage-2.dts')
-rw-r--r-- | arch/arm/boot/dts/marvell/orion5x-maxtor-shared-storage-2.dts | 176 |
1 files changed, 176 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/marvell/orion5x-maxtor-shared-storage-2.dts b/arch/arm/boot/dts/marvell/orion5x-maxtor-shared-storage-2.dts new file mode 100644 index 0000000000..d578599983 --- /dev/null +++ b/arch/arm/boot/dts/marvell/orion5x-maxtor-shared-storage-2.dts @@ -0,0 +1,176 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com> + * Copyright (C) Sylver Bruneau <sylver.bruneau@googlemail.com> + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include "orion5x-mv88f5182.dtsi" + +/ { + model = "Maxtor Shared Storage II"; + compatible = "maxtor,shared-storage-2", "marvell,orion5x-88f5182", "marvell,orion5x"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x4000000>; /* 64 MB */ + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + stdout-path = &uart0; + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>, + <MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>, + <MBUS_ID(0x01, 0x0f) 0 0xff800000 0x40000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-0 = <&pmx_buttons>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + power { + label = "Power"; + linux,code = <KEY_POWER>; + gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; + }; + + reset { + label = "Reset"; + linux,code = <KEY_RESTART>; + gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&devbus_bootcs { + status = "okay"; + + devbus,keep-config; + + /* + * Currently the MTD code does not recognize the MX29LV400CBCT + * as a bottom-type device. This could cause risks of + * accidentally erasing critical flash sectors. We thus define + * a single, write-protected partition covering the whole + * flash. TODO: once the flash part TOP/BOTTOM detection + * issue is sorted out in the MTD code, break this into at + * least three partitions: 'u-boot code', 'u-boot environment' + * and 'whatever is left'. + */ + flash@0 { + compatible = "cfi-flash"; + reg = <0 0x40000>; + bank-width = <1>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&mdio { + status = "okay"; + + ethphy: ethernet-phy { + reg = <8>; + }; +}; + +&ehci0 { + status = "okay"; +}; + +ð { + status = "okay"; + + ethernet-port@0 { + phy-handle = <ðphy>; + }; +}; + +&i2c { + status = "okay"; + clock-frequency = <100000>; + #address-cells = <1>; + + rtc@68 { + compatible = "st,m41t81"; + reg = <0x68>; + pinctrl-0 = <&pmx_rtc>; + pinctrl-names = "default"; + interrupt-parent = <&gpio0>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&pinctrl { + pinctrl-0 = <&pmx_leds &pmx_misc>; + pinctrl-names = "default"; + + pmx_buttons: pmx-buttons { + marvell,pins = "mpp11", "mpp12"; + marvell,function = "gpio"; + }; + + /* + * MPP0: Power LED + * MPP1: Error LED + */ + pmx_leds: pmx-leds { + marvell,pins = "mpp0", "mpp1"; + marvell,function = "gpio"; + }; + + /* + * MPP4: HDD ind. (Single/Dual) + * MPP5: HD0 5V control + * MPP6: HD0 12V control + * MPP7: HD1 5V control + * MPP8: HD1 12V control + */ + pmx_misc: pmx-misc { + marvell,pins = "mpp4", "mpp5", "mpp6", "mpp7", "mpp8", "mpp10"; + marvell,function = "gpio"; + }; + + pmx_rtc: pmx-rtc { + marvell,pins = "mpp3"; + marvell,function = "gpio"; + }; + + pmx_sata0_led_active: pmx-sata0-led-active { + marvell,pins = "mpp14"; + marvell,function = "sata0"; + }; + + pmx_sata1_led_active: pmx-sata1-led-active { + marvell,pins = "mpp15"; + marvell,function = "sata1"; + }; + + /* + * Non MPP GPIOs: + * GPIO 22: USB port 1 fuse (0 = Fail, 1 = Ok) + * GPIO 23: Blue front LED off + * GPIO 24: Inhibit board power off (0 = Disabled, 1 = Enabled) + */ +}; + +&sata { + pinctrl-0 = <&pmx_sata0_led_active + &pmx_sata1_led_active>; + pinctrl-names = "default"; + status = "okay"; + nr-ports = <2>; +}; + +&uart0 { + status = "okay"; +}; |