diff options
Diffstat (limited to 'arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-drc02.dtsi')
-rw-r--r-- | arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-drc02.dtsi | 143 |
1 files changed, 143 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-drc02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-drc02.dtsi new file mode 100644 index 0000000000..702cd4a1b2 --- /dev/null +++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-drc02.dtsi @@ -0,0 +1,143 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2021 DH electronics GmbH + */ + +/ { + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +/* + * Special SoM hardware required which uses the pins from micro SD card. The + * pins SD3_DAT0 and SD3_DAT1 are muxed as can2 Tx and Rx. The signals for can2 + * Tx and Rx are routed to the DHCOM UART1 rts/cts pins. Therefore the micro SD + * card must be disabled and the uart1 rts/cts must be output on other DHCOM + * pins, see uart1 and usdhc3 node below. + */ +&can2 { + status = "okay"; +}; + +&gpio1 { + /* + * NOTE: On DRC02, the RS485_RX_En is controlled by a separate + * GPIO line, however the i.MX6 UART driver assumes RX happens + * during TX anyway and that it only controls drive enable DE + * line. Hence, the RX is always enabled here. + */ + rs485-rx-en-hog { + gpio-hog; + gpios = <18 0>; /* GPIO Q */ + line-name = "rs485-rx-en"; + output-low; + }; +}; + +&gpio3 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "DRC02-In1", "", "", "", ""; +}; + +&gpio4 { + gpio-line-names = + "", "", "", "", "", "DHCOM-E", "DRC02-In2", "DHCOM-H", + "DHCOM-I", "DRC02-HW0", "", "", "", "", "", "", + "", "", "", "", "DRC02-Out1", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio6 { + gpio-line-names = + "", "", "", "DRC02-Out2", "", "", "SOM-HW1", "", + "", "", "", "", "", "", "DRC02-HW2", "DRC02-HW1", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&i2c1 { + eeprom@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + pagesize = <16>; + }; +}; + +&uart1 { + /* + * Due to the use of can2 the signals for can2 Tx and Rx are routed to + * DHCOM UART1 rts/cts pins. Therefore this UART have to use DHCOM GPIOs + * for rts/cts. So configure DHCOM GPIO I as rts and GPIO M as cts. + */ + /delete-property/ uart-has-rtscts; + cts-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>; /* GPIO M */ + pinctrl-0 = <&pinctrl_uart1 &pinctrl_dhcom_i &pinctrl_dhcom_m>; + pinctrl-names = "default"; + rts-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO I */ +}; + +&uart5 { + /* + * On DRC02 this UART is used as RS485 interface and RS485_TX_En is + * controlled by DHCOM GPIO P. So remove rts/cts pins and the property + * uart-has-rtscts from this UART and add the DHCOM GPIO P pin via + * rts-gpios. The RS485_RX_En is controlled by DHCOM GPIO Q, see gpio1 + * node above. + */ + /delete-property/ uart-has-rtscts; + linux,rs485-enabled-at-boot-time; + pinctrl-0 = <&pinctrl_uart5_core &pinctrl_dhcom_p &pinctrl_dhcom_q>; + pinctrl-names = "default"; + rts-gpios = <&gpio7 13 GPIO_ACTIVE_HIGH>; /* GPIO P */ +}; + +&usbh1 { + disable-over-current; +}; + +&usdhc2 { /* SD card */ + status = "okay"; +}; + +&usdhc3 { + /* + * Due to the use of can2 the micro SD card on module have to be + * disabled, because the pins SD3_DAT0 and SD3_DAT1 are muxed as + * can2 Tx and Rx. + */ + status = "disabled"; +}; + +&iomuxc { + pinctrl-0 = < + /* + * The following DHCOM GPIOs are used on this board. + * Therefore, they have been removed from the list below. + * I: uart1 rts + * M: uart1 cts + * P: uart5 rs485-tx-en + * Q: uart5 rs485-rx-en + */ + &pinctrl_hog_base + &pinctrl_dhcom_a &pinctrl_dhcom_b &pinctrl_dhcom_c + &pinctrl_dhcom_d &pinctrl_dhcom_e &pinctrl_dhcom_f + &pinctrl_dhcom_g &pinctrl_dhcom_h + &pinctrl_dhcom_j &pinctrl_dhcom_k &pinctrl_dhcom_l + &pinctrl_dhcom_n &pinctrl_dhcom_o + &pinctrl_dhcom_r + &pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u + &pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int + >; + pinctrl-names = "default"; + + pinctrl_uart5_core: uart5-core-grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x1b0b1 + >; + }; +}; |