diff options
Diffstat (limited to 'arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts')
-rw-r--r-- | arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts | 236 |
1 files changed, 236 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts b/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts new file mode 100644 index 0000000000..21a6d0bca1 --- /dev/null +++ b/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts @@ -0,0 +1,236 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * PHYTEC phyCORE-LPC3250 board + * + * Copyright (C) 2015-2019 Vladimir Zapolskiy <vz@mleia.com> + * Copyright 2012 Roland Stigge <stigge@antcom.de> + */ + +/dts-v1/; +#include "lpc32xx.dtsi" + +/ { + model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250"; + compatible = "phytec,phy3250", "nxp,lpc3250"; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x4000000>; + }; + + leds { + compatible = "gpio-leds"; + + led0 { /* red */ + gpios = <&gpio 5 1 0>; /* GPO_P3 1, GPIO 80, active high */ + default-state = "off"; + }; + + led1 { /* green */ + gpios = <&gpio 5 14 0>; /* GPO_P3 14, GPIO 93, active high */ + linux,default-trigger = "heartbeat"; + }; + }; + + panel: panel { + compatible = "sharp,lq035q7db03"; + power-supply = <®_lcd>; + + port { + panel_input: endpoint { + remote-endpoint = <&cldc_output>; + }; + }; + }; + + reg_backlight: regulator-backlight { + compatible = "regulator-fixed"; + regulator-name = "backlight"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio 5 4 0>; + enable-active-high; + regulator-boot-on; + }; + + reg_lcd: regulator-lcd { + compatible = "regulator-fixed"; + regulator-name = "lcd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio 5 0 0>; + enable-active-high; + regulator-boot-on; + }; + + reg_sd: regulator-sd { + compatible = "regulator-fixed"; + regulator-name = "sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio 5 5 0>; + enable-active-high; + regulator-boot-on; + }; +}; + +&clcd { + max-memory-bandwidth = <18710000>; + status = "okay"; + + port { + cldc_output: endpoint { + remote-endpoint = <&panel_input>; + arm,pl11x,tft-r0g0b0-pads = <0 8 16>; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + + uda1380: uda1380@18 { + compatible = "nxp,uda1380"; + reg = <0x18>; + power-gpio = <&gpio 3 10 0>; + reset-gpio = <&gpio 3 2 0>; + dac-clk = "wspll"; + }; + + pcf8563: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +&i2c2 { + clock-frequency = <100000>; +}; + +&i2cusb { + clock-frequency = <100000>; + + isp1301: usb-transceiver@2c { + compatible = "nxp,isp1301"; + reg = <0x2c>; + }; +}; + +&key { + keypad,num-rows = <1>; + keypad,num-columns = <1>; + nxp,debounce-delay-ms = <3>; + nxp,scan-delay-ms = <34>; + linux,keymap = <0x00000002>; + status = "okay"; +}; + +&mac { + phy-mode = "rmii"; + use-iram; + status = "okay"; +}; + +/* Here, choose exactly one from: ohci, usbd */ +&ohci /* &usbd */ { + transceiver = <&isp1301>; + status = "okay"; +}; + +&sd { + wp-gpios = <&gpio 3 0 0>; + cd-gpios = <&gpio 3 1 0>; + cd-inverted; + bus-width = <4>; + vmmc-supply = <®_sd>; + status = "okay"; +}; + +/* 64MB Flash via SLC NAND controller */ +&slc { + status = "okay"; + + nxp,wdr-clks = <14>; + nxp,wwidth = <40000000>; + nxp,whold = <100000000>; + nxp,wsetup = <100000000>; + nxp,rdr-clks = <14>; + nxp,rwidth = <40000000>; + nxp,rhold = <66666666>; + nxp,rsetup = <100000000>; + nand-on-flash-bbt; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + mtd0@0 { + label = "phy3250-boot"; + reg = <0x00000000 0x00064000>; + read-only; + }; + + mtd1@64000 { + label = "phy3250-uboot"; + reg = <0x00064000 0x00190000>; + read-only; + }; + + mtd2@1f4000 { + label = "phy3250-ubt-prms"; + reg = <0x001f4000 0x00010000>; + }; + + mtd3@204000 { + label = "phy3250-kernel"; + reg = <0x00204000 0x00400000>; + }; + + mtd4@604000 { + label = "phy3250-rootfs"; + reg = <0x00604000 0x039fc000>; + }; + }; +}; + +&ssp0 { + num-cs = <1>; + cs-gpios = <&gpio 3 5 0>; + status = "okay"; + + eeprom: at25@0 { + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; + + pl022,interface = <0>; + pl022,com-mode = <0>; + pl022,rx-level-trig = <1>; + pl022,tx-level-trig = <1>; + pl022,ctrl-len = <11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + + at25,byte-len = <0x8000>; + at25,addr-mode = <2>; + at25,page-size = <64>; + }; +}; + +&tsc { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; |