diff options
Diffstat (limited to 'arch/arm/boot/dts/st/ste-href-tvk1281618-r2.dtsi')
-rw-r--r-- | arch/arm/boot/dts/st/ste-href-tvk1281618-r2.dtsi | 289 |
1 files changed, 289 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/st/ste-href-tvk1281618-r2.dtsi b/arch/arm/boot/dts/st/ste-href-tvk1281618-r2.dtsi new file mode 100644 index 0000000000..37e59403c0 --- /dev/null +++ b/arch/arm/boot/dts/st/ste-href-tvk1281618-r2.dtsi @@ -0,0 +1,289 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Device Tree for the TVK1281618 R2 user interface board (UIB) + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/input/input.h> + +/ { + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>; + + button@139 { + /* Proximity sensor */ + gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>; + linux,code = <11>; /* SW_FRONT_PROXIMITY */ + label = "SFH7741 Proximity Sensor"; + }; + button@145 { + /* Hall sensor */ + gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>; + linux,code = <0>; /* SW_LID */ + label = "HED54XXU11 Hall Effect Sensor"; + }; + }; + + soc { + i2c@80004000 { + tc35893@44 { + compatible = "toshiba,tc35893"; + reg = <0x44>; + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&tc35893_tvk_mode>; + + interrupt-controller; + #interrupt-cells = <1>; + status = "disabled"; + + tc3589x_gpio { + compatible = "toshiba,tc3589x-gpio"; + interrupts = <0>; + + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; + tc3589x_keypad { + compatible = "toshiba,tc3589x-keypad"; + interrupts = <6>; + debounce-delay-ms = <4>; + keypad,num-columns = <8>; + keypad,num-rows = <8>; + linux,no-autorepeat; + wakeup-source; + linux,keymap = <MATRIX_KEY(3, 1, KEY_END)>, + <MATRIX_KEY(4, 1, KEY_HOME)>, + <MATRIX_KEY(6, 4, KEY_VOLUMEDOWN)>, + <MATRIX_KEY(4, 2, KEY_EMAIL)>, + <MATRIX_KEY(3, 3, KEY_RIGHT)>, + <MATRIX_KEY(2, 5, KEY_BACKSPACE)>, + <MATRIX_KEY(6, 7, KEY_MENU)>, + <MATRIX_KEY(5, 0, KEY_ENTER)>, + <MATRIX_KEY(4, 3, KEY_0)>, + <MATRIX_KEY(3, 4, KEY_DOT)>, + <MATRIX_KEY(5, 2, KEY_UP)>, + <MATRIX_KEY(3, 5, KEY_DOWN)>, + <MATRIX_KEY(4, 5, KEY_SEND)>, + <MATRIX_KEY(0, 5, KEY_BACK)>, + <MATRIX_KEY(6, 2, KEY_VOLUMEUP)>, + <MATRIX_KEY(1, 3, KEY_SPACE)>, + <MATRIX_KEY(7, 6, KEY_LEFT)>, + <MATRIX_KEY(5, 5, KEY_SEARCH)>; + }; + }; + }; + + i2c@80128000 { + accelerometer@18 { + /* Accelerometer */ + compatible = "st,lsm303dlh-accel"; + st,drdy-int-pin = <1>; + drive-open-drain; + reg = <0x18>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&accel_tvk_mode>; + /* + * These interrupts cannot be used: the other component + * ST-Micro L3D4200D gyro that is connected to the same lines + * cannot set its DRDY line to open drain, so it cannot be + * shared with other peripherals. The should be defined for + * the falling edge if they could be wired together. + * + * interrupts-extended = + * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, + * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; + */ + mount-matrix = "0", "1", "0", + "1", "0", "0", + "0", "0", "-1"; + }; + magnetometer@1e { + /* Magnetometer */ + compatible = "st,lsm303dlh-magn"; + reg = <0x1e>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + /* + * These interrupts cannot be used: the other component + * ST-Micro L3D4200D gyro that is connected to the same lines + * cannot set its DRDY line to open drain, so it cannot be + * shared with other peripherals. The should be defined for + * the falling edge if they could be wired together. + * + * interrupts-extended = + * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, + * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; + */ + }; + accelerometer@1c { + /* Accelerometer */ + compatible = "st,lis331dl-accel"; + st,drdy-int-pin = <1>; + reg = <0x1c>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&accel_tvk_mode>; + interrupt-parent = <&gpio2>; + /* INT2 would need to be open drain */ + interrupts = <18 IRQ_TYPE_EDGE_RISING>, + <19 IRQ_TYPE_EDGE_RISING>; + mount-matrix = "0", "-1", "0", + "-1", "0", "0", + "0", "0", "-1"; + }; + magnetometer@f { + /* Magnetometer */ + compatible = "asahi-kasei,ak8974"; + reg = <0x0f>; + avdd-supply = <&ab8500_ldo_aux1_reg>; + dvdd-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&gyro_magn_tvk_mode>; + /* + * These interrupts cannot be used: the other component + * ST-Micro L3D4200D gyro that is connected to the same lines + * cannot set its DRDY line to open drain, so it cannot be + * shared with other peripherals. The should be defined for + * the falling edge if they could be wired together. + * + * interrupts-extended = + * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, + * <&gpio0 31 IRQ_TYPE_EDGE_FALLING>; + */ + }; + gyroscope@68 { + /* Gyroscope */ + compatible = "st,l3g4200d-gyro"; + st,drdy-int-pin = <2>; + reg = <0x68>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&gyro_magn_tvk_mode>; + interrupts-extended = + <&gpio1 0 IRQ_TYPE_EDGE_RISING>, + <&gpio0 31 IRQ_TYPE_EDGE_RISING>; + }; + pressure@5c { + /* Barometer/pressure sensor */ + compatible = "st,lps001wp-press"; + reg = <0x5c>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + }; + }; + i2c@80110000 { + synaptics@4b { + /* Synaptics RMI4 TM1217 touchscreen */ + compatible = "syna,rmi4-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x4b>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&synaptics_tvk_mode>; + interrupt-parent = <&gpio2>; + interrupts = <20 IRQ_TYPE_EDGE_FALLING>; + + rmi4-f01@1 { + reg = <0x1>; + syna,nosleep = <1>; + }; + rmi4-f11@11 { + reg = <0x11>; + syna,sensor-type = <1>; + /* This is a landscape display */ + touchscreen-swapped-x-y; + }; + }; + }; + mcde@a0350000 { + status = "okay"; + + dsi@a0351000 { + panel { + compatible = "samsung,s6d16d0"; + reg = <0>; + vdd1-supply = <&ab8500_ldo_aux1_reg>; + reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; + }; + }; + }; + pinctrl { + prox { + prox_tvk_mode: prox_tvk { + tvk_cfg { + pins = "GPIO217_AH12"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + hall { + hall_tvk_mode: hall_tvk { + tvk_cfg { + pins = "GPIO145_C13"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + tc35893 { + /* IRQ from the TC35893 */ + tc35893_tvk_mode: tc35893_tvk { + tvk_cfg { + pins = "GPIO218_AH11"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + accelerometer { + accel_tvk_mode: accel_tvk { + /* Accelerometer interrupt lines 1 & 2 */ + tvk_cfg { + pins = "GPIO82_C1", "GPIO83_D3"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + gyroscope { + /* + * These lines are shared between Gyroscope l3g400dh + * and AK8974 magnetometer. + */ + gyro_magn_tvk_mode: gyro_magn_tvk { + /* GPIO 31 used for INT pull down the line */ + tvk_cfg1 { + pins = "GPIO31_V3"; + ste,config = <&gpio_in_pd>; + }; + /* GPIO 32 used for DRDY, pull this down */ + tvk_cfg2 { + pins = "GPIO32_V2"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + synaptics { + synaptics_tvk_mode: synaptics_tvk { + /* Touchscreen uses GPIO 84 */ + tvk_cfg1 { + pins = "GPIO84_C2"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + }; + }; +}; |