diff options
Diffstat (limited to 'arch/arm/boot/dts/ti/davinci/da850-evm.dts')
-rw-r--r-- | arch/arm/boot/dts/ti/davinci/da850-evm.dts | 466 |
1 files changed, 466 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/ti/davinci/da850-evm.dts b/arch/arm/boot/dts/ti/davinci/da850-evm.dts new file mode 100644 index 0000000000..6c5936278e --- /dev/null +++ b/arch/arm/boot/dts/ti/davinci/da850-evm.dts @@ -0,0 +1,466 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Device Tree for DA850 EVM board + * + * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/ + */ +/dts-v1/; +#include "da850.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + compatible = "ti,da850-evm", "ti,da850"; + model = "DA850/AM1808/OMAP-L138 EVM"; + + chosen { + stdout-path = &serial2; + }; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + serial2 = &serial2; + ethernet0 = ð0; + spi0 = &spi1; + }; + + backlight: backlight-pwm { + pinctrl-names = "default"; + pinctrl-0 = <&ecap2_pins>; + power-supply = <&backlight_lcd>; + compatible = "pwm-backlight"; + /* + * The PWM here corresponds to production hardware. The + * schematic needs to be 1015171 (15 March 2010), Rev A + * or newer. + */ + pwms = <&ecap2 0 50000 0>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 99>; + default-brightness-level = <7>; + }; + + panel { + compatible = "ti,tilcdc,panel"; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pins>; + /* + * The vpif and the LCD are mutually exclusive. + * To enable VPIF, change the status below to 'disabled' then + * then change the status of the vpif below to 'okay' + */ + status = "okay"; + enable-gpios = <&gpio 40 GPIO_ACTIVE_HIGH>; /* lcd_panel_pwr */ + + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <16>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + + display-timings { + native-mode = <&timing0>; + timing0: 480x272 { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <3>; + hback-porch = <2>; + hsync-len = <42>; + vback-porch = <3>; + vfront-porch = <4>; + vsync-len = <11>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + }; + + vbat: fixedregulator0 { + compatible = "regulator-fixed"; + regulator-name = "vbat"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + + baseboard_3v3: fixedregulator-3v3 { + /* TPS73701DCQ */ + compatible = "regulator-fixed"; + regulator-name = "baseboard_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vbat>; + regulator-always-on; + regulator-boot-on; + }; + + baseboard_1v8: fixedregulator-1v8 { + /* TPS73701DCQ */ + compatible = "regulator-fixed"; + regulator-name = "baseboard_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vbat>; + regulator-always-on; + regulator-boot-on; + }; + + backlight_lcd: backlight-regulator { + compatible = "regulator-fixed"; + regulator-name = "lcd_backlight_pwr"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio 47 GPIO_ACTIVE_HIGH>; /* lcd_backlight_pwr */ + enable-active-high; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "DA850-OMAPL138 EVM"; + simple-audio-card,widgets = + "Line", "Line In", + "Line", "Line Out"; + simple-audio-card,routing = + "LINE1L", "Line In", + "LINE1R", "Line In", + "Line Out", "LLOUT", + "Line Out", "RLOUT"; + simple-audio-card,format = "dsp_b"; + simple-audio-card,bitclock-master = <&link0_codec>; + simple-audio-card,frame-master = <&link0_codec>; + simple-audio-card,bitclock-inversion; + + simple-audio-card,cpu { + sound-dai = <&mcasp0>; + system-clock-frequency = <24576000>; + }; + + link0_codec: simple-audio-card,codec { + sound-dai = <&tlv320aic3106>; + system-clock-frequency = <24576000>; + }; + }; +}; + +&ecap2 { + status = "okay"; +}; + +&ref_clk { + clock-frequency = <24000000>; +}; + +&pmx_core { + status = "okay"; + + mcasp0_pins: mcasp0-pins { + pinctrl-single,bits = < + /* + * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR, + * AFSR, AMUTE + */ + 0x00 0x11111111 0xffffffff + /* AXR11, AXR12 */ + 0x04 0x00011000 0x000ff000 + >; + }; + nand_pins: nand-pins { + pinctrl-single,bits = < + /* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */ + 0x1c 0x10110110 0xf0ff0ff0 + /* + * EMA_D[0], EMA_D[1], EMA_D[2], + * EMA_D[3], EMA_D[4], EMA_D[5], + * EMA_D[6], EMA_D[7] + */ + 0x24 0x11111111 0xffffffff + /* EMA_A[1], EMA_A[2] */ + 0x30 0x01100000 0x0ff00000 + >; + }; +}; + +&cpu { + cpu-supply = <&vdcdc3_reg>; +}; + +/* + * The standard da850-evm kits and SOM's are 375MHz so enable this operating + * point by default. Higher frequencies must be enabled for custom boards with + * other variants of the SoC. + */ +&opp_375 { + status = "okay"; +}; + +&sata { + status = "okay"; +}; + +&serial0 { + status = "okay"; +}; + +&serial1 { + status = "okay"; +}; + +&serial2 { + status = "okay"; +}; + +&rtc0 { + status = "okay"; +}; + +&lcdc { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + tps: tps@48 { + reg = <0x48>; + }; + tlv320aic3106: tlv320aic3106@18 { + #sound-dai-cells = <0>; + compatible = "ti,tlv320aic3106"; + reg = <0x18>; + status = "okay"; + + /* Regulators */ + IOVDD-supply = <&vdcdc2_reg>; + AVDD-supply = <&baseboard_3v3>; + DRVDD-supply = <&baseboard_3v3>; + DVDD-supply = <&baseboard_1v8>; + }; + tca6416: gpio@20 { + compatible = "ti,tca6416"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; + tca6416_bb: gpio@21 { + compatible = "ti,tca6416"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&wdt { + status = "okay"; +}; + +&mmc0 { + max-frequency = <50000000>; + bus-width = <4>; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + cd-gpios = <&gpio 64 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio 65 GPIO_ACTIVE_HIGH>; +}; + +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins &spi1_cs0_pin>; + flash: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <30000000>; + m25p,fast-read; + reg = <0>; + partition@0 { + label = "U-Boot-SPL"; + reg = <0x00000000 0x00010000>; + read-only; + }; + partition@1 { + label = "U-Boot"; + reg = <0x00010000 0x00080000>; + read-only; + }; + partition@2 { + label = "U-Boot-Env"; + reg = <0x00090000 0x00010000>; + read-only; + }; + partition@3 { + label = "Kernel"; + reg = <0x000a0000 0x00280000>; + }; + partition@4 { + label = "Filesystem"; + reg = <0x00320000 0x00400000>; + }; + partition@5 { + label = "MAC-Address"; + reg = <0x007f0000 0x00010000>; + read-only; + }; + }; +}; + +&mdio { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + bus_freq = <2200000>; +}; + +ð0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mii_pins>; +}; + +&gpio { + status = "okay"; +}; + +/include/ "../../tps6507x.dtsi" + +&tps { + vdcdc1_2-supply = <&vbat>; + vdcdc3-supply = <&vbat>; + vldo1_2-supply = <&vbat>; + + regulators { + vdcdc1_reg: regulator@0 { + regulator-name = "VDCDC1_3.3V"; + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3450000>; + regulator-always-on; + regulator-boot-on; + }; + + vdcdc2_reg: regulator@1 { + regulator-name = "VDCDC2_3.3V"; + regulator-min-microvolt = <1710000>; + regulator-max-microvolt = <3450000>; + regulator-always-on; + regulator-boot-on; + ti,defdcdc_default = <1>; + }; + + vdcdc3_reg: regulator@2 { + regulator-name = "VDCDC3_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + ti,defdcdc_default = <1>; + }; + + ldo1_reg: regulator@3 { + regulator-name = "LDO1_1.8V"; + regulator-min-microvolt = <1710000>; + regulator-max-microvolt = <1890000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo2_reg: regulator@4 { + regulator-name = "LDO2_1.2V"; + regulator-min-microvolt = <1140000>; + regulator-max-microvolt = <1320000>; + regulator-always-on; + regulator-boot-on; + }; + }; +}; + +&mcasp0 { + #sound-dai-cells = <0>; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcasp0_pins>; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + /* 4 serializer */ + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 0 0 + 0 0 0 0 + 0 0 0 1 + 2 0 0 0 + >; + tx-num-evt = <32>; + rx-num-evt = <32>; +}; + +&edma0 { + ti,edma-reserved-slot-ranges = <32 50>; +}; + +&edma1 { + ti,edma-reserved-slot-ranges = <32 90>; +}; + +&aemif { + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins>; + status = "okay"; + cs3 { + #address-cells = <2>; + #size-cells = <1>; + clock-ranges; + ranges; + + ti,cs-chipselect = <3>; + + nand@2000000,0 { + compatible = "ti,davinci-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0 0x02000000 0x02000000 + 1 0x00000000 0x00008000>; + + ti,davinci-chipselect = <1>; + ti,davinci-mask-ale = <0>; + ti,davinci-mask-cle = <0>; + ti,davinci-mask-chipsel = <0>; + ti,davinci-ecc-mode = "hw"; + ti,davinci-ecc-bits = <4>; + ti,davinci-nand-use-bbt; + }; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; + +&vpif { + pinctrl-names = "default"; + pinctrl-0 = <&vpif_capture_pins>, <&vpif_display_pins>; + /* + * The vpif and the LCD are mutually exclusive. + * To enable VPIF, disable the ti,tilcdc,panel then + * change the status below to 'okay' + */ + status = "disabled"; +}; |