1 files changed, 434 insertions, 0 deletions
diff --git a/arch/arm/mach-pxa/pxa3xx.c b/arch/arm/mach-pxa/pxa3xx.c
new file mode 100644
index 0000000000..1d1e571346
--- /dev/null
+++ b/arch/arm/mach-pxa/pxa3xx.c
@@ -0,0 +1,434 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * linux/arch/arm/mach-pxa/pxa3xx.c
+ *
+ * code specific to pxa3xx aka Monahans
+ *
+ * Copyright (C) 2006 Marvell International Ltd.
+ *
+ * 2007-09-02: eric miao <eric.miao@marvell.com>
+ *             initial version
+ */
+#include <linux/dmaengine.h>
+#include <linux/dma/pxa-dma.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/gpio-pxa.h>
+#include <linux/pm.h>
+#include <linux/platform_device.h>
+#include <linux/irq.h>
+#include <linux/irqchip.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/syscore_ops.h>
+#include <linux/platform_data/i2c-pxa.h>
+#include <linux/platform_data/mmp_dma.h>
+#include <linux/soc/pxa/cpu.h>
+#include <linux/clk/pxa.h>
+
+#include <asm/mach/map.h>
+#include <asm/suspend.h>
+#include "pxa3xx-regs.h"
+#include "reset.h"
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include "pm.h"
+#include "addr-map.h"
+#include "smemc.h"
+#include "irqs.h"
+
+#include "generic.h"
+#include "devices.h"
+
+#define PECR_IE(n)	((1 << ((n) * 2)) << 28)
+#define PECR_IS(n)	((1 << ((n) * 2)) << 29)
+
+extern void __init pxa_dt_irq_init(int (*fn)(struct irq_data *, unsigned int));
+
+/*
+ * NAND NFC: DFI bus arbitration subset
+ */
+#define NDCR			(*(volatile u32 __iomem*)(NAND_VIRT + 0))
+#define NDCR_ND_ARB_EN		(1 << 12)
+#define NDCR_ND_ARB_CNTL	(1 << 19)
+
+#define CKEN_BOOT  		11      /* < Boot rom clock enable */
+#define CKEN_TPM   		19      /* < TPM clock enable */
+#define CKEN_HSIO2 		41      /* < HSIO2 clock enable */
+
+#ifdef CONFIG_PM
+
+#define ISRAM_START	0x5c000000
+#define ISRAM_SIZE	SZ_256K
+
+static void __iomem *sram;
+static unsigned long wakeup_src;
+
+/*
+ * Enter a standby mode (S0D1C2 or S0D2C2).  Upon wakeup, the dynamic
+ * memory controller has to be reinitialised, so we place some code
+ * in the SRAM to perform this function.
+ *
+ * We disable FIQs across the standby - otherwise, we might receive a
+ * FIQ while the SDRAM is unavailable.
+ */
+static void pxa3xx_cpu_standby(unsigned int pwrmode)
+{
+	void (*fn)(unsigned int) = (void __force *)(sram + 0x8000);
+
+	memcpy_toio(sram + 0x8000, pm_enter_standby_start,
+		    pm_enter_standby_end - pm_enter_standby_start);
+
+	AD2D0SR = ~0;
+	AD2D1SR = ~0;
+	AD2D0ER = wakeup_src;
+	AD2D1ER = 0;
+	ASCR = ASCR;
+	ARSR = ARSR;
+
+	local_fiq_disable();
+	fn(pwrmode);
+	local_fiq_enable();
+
+	AD2D0ER = 0;
+	AD2D1ER = 0;
+}
+
+/*
+ * NOTE:  currently, the OBM (OEM Boot Module) binary comes along with
+ * PXA3xx development kits assumes that the resuming process continues
+ * with the address stored within the first 4 bytes of SDRAM. The PSPR
+ * register is used privately by BootROM and OBM, and _must_ be set to
+ * 0x5c014000 for the moment.
+ */
+static void pxa3xx_cpu_pm_suspend(void)
+{
+	volatile unsigned long *p = (volatile void *)0xc0000000;
+	unsigned long saved_data = *p;
+#ifndef CONFIG_IWMMXT
+	u64 acc0;
+
+#ifdef CONFIG_CC_IS_GCC
+	asm volatile(".arch_extension xscale\n\t"
+		     "mra %Q0, %R0, acc0" : "=r" (acc0));
+#else
+	asm volatile("mrrc p0, 0, %Q0, %R0, c0" : "=r" (acc0));
+#endif
+#endif
+
+	/* resuming from D2 requires the HSIO2/BOOT/TPM clocks enabled */
+	CKENA |= (1 << CKEN_BOOT) | (1 << CKEN_TPM);
+	CKENB |= 1 << (CKEN_HSIO2 & 0x1f);
+
+	/* clear and setup wakeup source */
+	AD3SR = ~0;
+	AD3ER = wakeup_src;
+	ASCR = ASCR;
+	ARSR = ARSR;
+
+	PCFR |= (1u << 13);			/* L1_DIS */
+	PCFR &= ~((1u << 12) | (1u << 1));	/* L0_EN | SL_ROD */
+
+	PSPR = 0x5c014000;
+
+	/* overwrite with the resume address */
+	*p = __pa_symbol(cpu_resume);
+
+	cpu_suspend(0, pxa3xx_finish_suspend);
+
+	*p = saved_data;
+
+	AD3ER = 0;
+
+#ifndef CONFIG_IWMMXT
+#ifndef CONFIG_AS_IS_LLVM
+	asm volatile(".arch_extension xscale\n\t"
+		     "mar acc0, %Q0, %R0" : "=r" (acc0));
+#else
+	asm volatile("mcrr p0, 0, %Q0, %R0, c0" :: "r" (acc0));
+#endif
+#endif
+}
+
+static void pxa3xx_cpu_pm_enter(suspend_state_t state)
+{
+	/*
+	 * Don't sleep if no wakeup sources are defined
+	 */
+	if (wakeup_src == 0) {
+		printk(KERN_ERR "Not suspending: no wakeup sources\n");
+		return;
+	}
+
+	switch (state) {
+	case PM_SUSPEND_STANDBY:
+		pxa3xx_cpu_standby(PXA3xx_PM_S0D2C2);
+		break;
+
+	case PM_SUSPEND_MEM:
+		pxa3xx_cpu_pm_suspend();
+		break;
+	}
+}
+
+static int pxa3xx_cpu_pm_valid(suspend_state_t state)
+{
+	return state == PM_SUSPEND_MEM || state == PM_SUSPEND_STANDBY;
+}
+
+static struct pxa_cpu_pm_fns pxa3xx_cpu_pm_fns = {
+	.valid		= pxa3xx_cpu_pm_valid,
+	.enter		= pxa3xx_cpu_pm_enter,
+};
+
+static void __init pxa3xx_init_pm(void)
+{
+	sram = ioremap(ISRAM_START, ISRAM_SIZE);
+	if (!sram) {
+		printk(KERN_ERR "Unable to map ISRAM: disabling standby/suspend\n");
+		return;
+	}
+
+	/*
+	 * Since we copy wakeup code into the SRAM, we need to ensure
+	 * that it is preserved over the low power modes.  Note: bit 8
+	 * is undocumented in the developer manual, but must be set.
+	 */
+	AD1R |= ADXR_L2 | ADXR_R0;
+	AD2R |= ADXR_L2 | ADXR_R0;
+	AD3R |= ADXR_L2 | ADXR_R0;
+
+	/*
+	 * Clear the resume enable registers.
+	 */
+	AD1D0ER = 0;
+	AD2D0ER = 0;
+	AD2D1ER = 0;
+	AD3ER = 0;
+
+	pxa_cpu_pm_fns = &pxa3xx_cpu_pm_fns;
+}
+
+static int pxa3xx_set_wake(struct irq_data *d, unsigned int on)
+{
+	unsigned long flags, mask = 0;
+
+	switch (d->irq) {
+	case IRQ_SSP3:
+		mask = ADXER_MFP_WSSP3;
+		break;
+	case IRQ_MSL:
+		mask = ADXER_WMSL0;
+		break;
+	case IRQ_USBH2:
+	case IRQ_USBH1:
+		mask = ADXER_WUSBH;
+		break;
+	case IRQ_KEYPAD:
+		mask = ADXER_WKP;
+		break;
+	case IRQ_AC97:
+		mask = ADXER_MFP_WAC97;
+		break;
+	case IRQ_USIM:
+		mask = ADXER_WUSIM0;
+		break;
+	case IRQ_SSP2:
+		mask = ADXER_MFP_WSSP2;
+		break;
+	case IRQ_I2C:
+		mask = ADXER_MFP_WI2C;
+		break;
+	case IRQ_STUART:
+		mask = ADXER_MFP_WUART3;
+		break;
+	case IRQ_BTUART:
+		mask = ADXER_MFP_WUART2;
+		break;
+	case IRQ_FFUART:
+		mask = ADXER_MFP_WUART1;
+		break;
+	case IRQ_MMC:
+		mask = ADXER_MFP_WMMC1;
+		break;
+	case IRQ_SSP:
+		mask = ADXER_MFP_WSSP1;
+		break;
+	case IRQ_RTCAlrm:
+		mask = ADXER_WRTC;
+		break;
+	case IRQ_SSP4:
+		mask = ADXER_MFP_WSSP4;
+		break;
+	case IRQ_TSI:
+		mask = ADXER_WTSI;
+		break;
+	case IRQ_USIM2:
+		mask = ADXER_WUSIM1;
+		break;
+	case IRQ_MMC2:
+		mask = ADXER_MFP_WMMC2;
+		break;
+	case IRQ_NAND:
+		mask = ADXER_MFP_WFLASH;
+		break;
+	case IRQ_USB2:
+		mask = ADXER_WUSB2;
+		break;
+	case IRQ_WAKEUP0:
+		mask = ADXER_WEXTWAKE0;
+		break;
+	case IRQ_WAKEUP1:
+		mask = ADXER_WEXTWAKE1;
+		break;
+	case IRQ_MMC3:
+		mask = ADXER_MFP_GEN12;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	local_irq_save(flags);
+	if (on)
+		wakeup_src |= mask;
+	else
+		wakeup_src &= ~mask;
+	local_irq_restore(flags);
+
+	return 0;
+}
+#else
+static inline void pxa3xx_init_pm(void) {}
+#define pxa3xx_set_wake	NULL
+#endif
+
+static void pxa_ack_ext_wakeup(struct irq_data *d)
+{
+	PECR |= PECR_IS(d->irq - IRQ_WAKEUP0);
+}
+
+static void pxa_mask_ext_wakeup(struct irq_data *d)
+{
+	pxa_mask_irq(d);
+	PECR &= ~PECR_IE(d->irq - IRQ_WAKEUP0);
+}
+
+static void pxa_unmask_ext_wakeup(struct irq_data *d)
+{
+	pxa_unmask_irq(d);
+	PECR |= PECR_IE(d->irq - IRQ_WAKEUP0);
+}
+
+static int pxa_set_ext_wakeup_type(struct irq_data *d, unsigned int flow_type)
+{
+	if (flow_type & IRQ_TYPE_EDGE_RISING)
+		PWER |= 1 << (d->irq - IRQ_WAKEUP0);
+
+	if (flow_type & IRQ_TYPE_EDGE_FALLING)
+		PWER |= 1 << (d->irq - IRQ_WAKEUP0 + 2);
+
+	return 0;
+}
+
+static struct irq_chip pxa_ext_wakeup_chip = {
+	.name		= "WAKEUP",
+	.irq_ack	= pxa_ack_ext_wakeup,
+	.irq_mask	= pxa_mask_ext_wakeup,
+	.irq_unmask	= pxa_unmask_ext_wakeup,
+	.irq_set_type	= pxa_set_ext_wakeup_type,
+};
+
+static void __init pxa_init_ext_wakeup_irq(int (*fn)(struct irq_data *,
+					   unsigned int))
+{
+	int irq;
+
+	for (irq = IRQ_WAKEUP0; irq <= IRQ_WAKEUP1; irq++) {
+		irq_set_chip_and_handler(irq, &pxa_ext_wakeup_chip,
+					 handle_edge_irq);
+		irq_clear_status_flags(irq, IRQ_NOREQUEST);
+	}
+
+	pxa_ext_wakeup_chip.irq_set_wake = fn;
+}
+
+static void __init __pxa3xx_init_irq(void)
+{
+	/* enable CP6 access */
+	u32 value;
+	__asm__ __volatile__("mrc p15, 0, %0, c15, c1, 0\n": "=r"(value));
+	value |= (1 << 6);
+	__asm__ __volatile__("mcr p15, 0, %0, c15, c1, 0\n": :"r"(value));
+
+	pxa_init_ext_wakeup_irq(pxa3xx_set_wake);
+}
+
+static int __init __init
+pxa3xx_dt_init_irq(struct device_node *node, struct device_node *parent)
+{
+	__pxa3xx_init_irq();
+	pxa_dt_irq_init(pxa3xx_set_wake);
+	set_handle_irq(ichp_handle_irq);
+
+	return 0;
+}
+IRQCHIP_DECLARE(pxa3xx_intc, "marvell,pxa-intc", pxa3xx_dt_init_irq);
+
+static struct map_desc pxa3xx_io_desc[] __initdata = {
+	{	/* Mem Ctl */
+		.virtual	= (unsigned long)SMEMC_VIRT,
+		.pfn		= __phys_to_pfn(PXA3XX_SMEMC_BASE),
+		.length		= SMEMC_SIZE,
+		.type		= MT_DEVICE
+	}, {
+		.virtual	= (unsigned long)NAND_VIRT,
+		.pfn		= __phys_to_pfn(NAND_PHYS),
+		.length		= NAND_SIZE,
+		.type		= MT_DEVICE
+	},
+};
+
+void __init pxa3xx_map_io(void)
+{
+	pxa_map_io();
+	iotable_init(ARRAY_AND_SIZE(pxa3xx_io_desc));
+	pxa3xx_get_clk_frequency_khz(1);
+}
+
+static int __init pxa3xx_init(void)
+{
+	int ret = 0;
+
+	if (cpu_is_pxa3xx()) {
+
+		pxa_register_wdt(ARSR);
+
+		/*
+		 * clear RDH bit every time after reset
+		 *
+		 * Note: the last 3 bits DxS are write-1-to-clear so carefully
+		 * preserve them here in case they will be referenced later
+		 */
+		ASCR &= ~(ASCR_RDH | ASCR_D1S | ASCR_D2S | ASCR_D3S);
+
+		/*
+		 * Disable DFI bus arbitration, to prevent a system bus lock if
+		 * somebody disables the NAND clock (unused clock) while this
+		 * bit remains set.
+		 */
+		NDCR = (NDCR & ~NDCR_ND_ARB_EN) | NDCR_ND_ARB_CNTL;
+
+		pxa3xx_init_pm();
+
+		enable_irq_wake(IRQ_WAKEUP0);
+		if (cpu_is_pxa320())
+			enable_irq_wake(IRQ_WAKEUP1);
+
+		register_syscore_ops(&pxa_irq_syscore_ops);
+		register_syscore_ops(&pxa3xx_mfp_syscore_ops);
+	}
+
+	return ret;
+}
+
+postcore_initcall(pxa3xx_init);