diff options
Diffstat (limited to 'arch/arm/mm/proc-arm1020e.S')
| -rw-r--r-- | arch/arm/mm/proc-arm1020e.S | 475 |
1 files changed, 475 insertions, 0 deletions
diff --git a/arch/arm/mm/proc-arm1020e.S b/arch/arm/mm/proc-arm1020e.S new file mode 100644 index 0000000000..df49b10250 --- /dev/null +++ b/arch/arm/mm/proc-arm1020e.S @@ -0,0 +1,475 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ +/* + * linux/arch/arm/mm/proc-arm1020e.S: MMU functions for ARM1020 + * + * Copyright (C) 2000 ARM Limited + * Copyright (C) 2000 Deep Blue Solutions Ltd. + * hacked for non-paged-MM by Hyok S. Choi, 2003. + * + * These are the low level assembler for performing cache and TLB + * functions on the arm1020e. + */ +#include <linux/linkage.h> +#include <linux/init.h> +#include <linux/pgtable.h> +#include <asm/assembler.h> +#include <asm/asm-offsets.h> +#include <asm/hwcap.h> +#include <asm/pgtable-hwdef.h> +#include <asm/ptrace.h> + +#include "proc-macros.S" + +/* + * This is the maximum size of an area which will be invalidated + * using the single invalidate entry instructions. Anything larger + * than this, and we go for the whole cache. + * + * This value should be chosen such that we choose the cheapest + * alternative. + */ +#define MAX_AREA_SIZE 32768 + +/* + * The size of one data cache line. + */ +#define CACHE_DLINESIZE 32 + +/* + * The number of data cache segments. + */ +#define CACHE_DSEGMENTS 16 + +/* + * The number of lines in a cache segment. + */ +#define CACHE_DENTRIES 64 + +/* + * This is the size at which it becomes more efficient to + * clean the whole cache, rather than using the individual + * cache line maintenance instructions. + */ +#define CACHE_DLIMIT 32768 + + .text +/* + * cpu_arm1020e_proc_init() + */ +ENTRY(cpu_arm1020e_proc_init) + ret lr + +/* + * cpu_arm1020e_proc_fin() + */ +ENTRY(cpu_arm1020e_proc_fin) + mrc p15, 0, r0, c1, c0, 0 @ ctrl register + bic r0, r0, #0x1000 @ ...i............ + bic r0, r0, #0x000e @ ............wca. + mcr p15, 0, r0, c1, c0, 0 @ disable caches + ret lr + +/* + * cpu_arm1020e_reset(loc) + * + * Perform a soft reset of the system. Put the CPU into the + * same state as it would be if it had been reset, and branch + * to what would be the reset vector. + * + * loc: location to jump to for soft reset + */ + .align 5 + .pushsection .idmap.text, "ax" +ENTRY(cpu_arm1020e_reset) + mov ip, #0 + mcr p15, 0, ip, c7, c7, 0 @ invalidate I,D caches + mcr p15, 0, ip, c7, c10, 4 @ drain WB +#ifdef CONFIG_MMU + mcr p15, 0, ip, c8, c7, 0 @ invalidate I & D TLBs +#endif + mrc p15, 0, ip, c1, c0, 0 @ ctrl register + bic ip, ip, #0x000f @ ............wcam + bic ip, ip, #0x1100 @ ...i...s........ + mcr p15, 0, ip, c1, c0, 0 @ ctrl register + ret r0 +ENDPROC(cpu_arm1020e_reset) + .popsection + +/* + * cpu_arm1020e_do_idle() + */ + .align 5 +ENTRY(cpu_arm1020e_do_idle) + mcr p15, 0, r0, c7, c0, 4 @ Wait for interrupt + ret lr + +/* ================================= CACHE ================================ */ + + .align 5 + +/* + * flush_icache_all() + * + * Unconditionally clean and invalidate the entire icache. + */ +ENTRY(arm1020e_flush_icache_all) +#ifndef CONFIG_CPU_ICACHE_DISABLE + mov r0, #0 + mcr p15, 0, r0, c7, c5, 0 @ invalidate I cache +#endif + ret lr +ENDPROC(arm1020e_flush_icache_all) + +/* + * flush_user_cache_all() + * + * Invalidate all cache entries in a particular address + * space. + */ +ENTRY(arm1020e_flush_user_cache_all) + /* FALLTHROUGH */ +/* + * flush_kern_cache_all() + * + * Clean and invalidate the entire cache. + */ +ENTRY(arm1020e_flush_kern_cache_all) + mov r2, #VM_EXEC + mov ip, #0 +__flush_whole_cache: +#ifndef CONFIG_CPU_DCACHE_DISABLE + mcr p15, 0, ip, c7, c10, 4 @ drain WB + mov r1, #(CACHE_DSEGMENTS - 1) << 5 @ 16 segments +1: orr r3, r1, #(CACHE_DENTRIES - 1) << 26 @ 64 entries +2: mcr p15, 0, r3, c7, c14, 2 @ clean+invalidate D index + subs r3, r3, #1 << 26 + bcs 2b @ entries 63 to 0 + subs r1, r1, #1 << 5 + bcs 1b @ segments 15 to 0 +#endif + tst r2, #VM_EXEC +#ifndef CONFIG_CPU_ICACHE_DISABLE + mcrne p15, 0, ip, c7, c5, 0 @ invalidate I cache +#endif + mcrne p15, 0, ip, c7, c10, 4 @ drain WB + ret lr + +/* + * flush_user_cache_range(start, end, flags) + * + * Invalidate a range of cache entries in the specified + * address space. + * + * - start - start address (inclusive) + * - end - end address (exclusive) + * - flags - vm_flags for this space + */ +ENTRY(arm1020e_flush_user_cache_range) + mov ip, #0 + sub r3, r1, r0 @ calculate total size + cmp r3, #CACHE_DLIMIT + bhs __flush_whole_cache + +#ifndef CONFIG_CPU_DCACHE_DISABLE +1: mcr p15, 0, r0, c7, c14, 1 @ clean+invalidate D entry + add r0, r0, #CACHE_DLINESIZE + cmp r0, r1 + blo 1b +#endif + tst r2, #VM_EXEC +#ifndef CONFIG_CPU_ICACHE_DISABLE + mcrne p15, 0, ip, c7, c5, 0 @ invalidate I cache +#endif + mcrne p15, 0, ip, c7, c10, 4 @ drain WB + ret lr + +/* + * coherent_kern_range(start, end) + * + * Ensure coherency between the Icache and the Dcache in the + * region described by start. If you have non-snooping + * Harvard caches, you need to implement this function. + * + * - start - virtual start address + * - end - virtual end address + */ +ENTRY(arm1020e_coherent_kern_range) + /* FALLTHROUGH */ +/* + * coherent_user_range(start, end) + * + * Ensure coherency between the Icache and the Dcache in the + * region described by start. If you have non-snooping + * Harvard caches, you need to implement this function. + * + * - start - virtual start address + * - end - virtual end address + */ +ENTRY(arm1020e_coherent_user_range) + mov ip, #0 + bic r0, r0, #CACHE_DLINESIZE - 1 +1: +#ifndef CONFIG_CPU_DCACHE_DISABLE + mcr p15, 0, r0, c7, c10, 1 @ clean D entry +#endif +#ifndef CONFIG_CPU_ICACHE_DISABLE + mcr p15, 0, r0, c7, c5, 1 @ invalidate I entry +#endif + add r0, r0, #CACHE_DLINESIZE + cmp r0, r1 + blo 1b + mcr p15, 0, ip, c7, c10, 4 @ drain WB + mov r0, #0 + ret lr + +/* + * flush_kern_dcache_area(void *addr, size_t size) + * + * Ensure no D cache aliasing occurs, either with itself or + * the I cache + * + * - addr - kernel address + * - size - region size + */ +ENTRY(arm1020e_flush_kern_dcache_area) + mov ip, #0 +#ifndef CONFIG_CPU_DCACHE_DISABLE + add r1, r0, r1 +1: mcr p15, 0, r0, c7, c14, 1 @ clean+invalidate D entry + add r0, r0, #CACHE_DLINESIZE + cmp r0, r1 + blo 1b +#endif + mcr p15, 0, ip, c7, c10, 4 @ drain WB + ret lr + +/* + * dma_inv_range(start, end) + * + * Invalidate (discard) the specified virtual address range. + * May not write back any entries. If 'start' or 'end' + * are not cache line aligned, those lines must be written + * back. + * + * - start - virtual start address + * - end - virtual end address + * + * (same as v4wb) + */ +arm1020e_dma_inv_range: + mov ip, #0 +#ifndef CONFIG_CPU_DCACHE_DISABLE + tst r0, #CACHE_DLINESIZE - 1 + bic r0, r0, #CACHE_DLINESIZE - 1 + mcrne p15, 0, r0, c7, c10, 1 @ clean D entry + tst r1, #CACHE_DLINESIZE - 1 + mcrne p15, 0, r1, c7, c10, 1 @ clean D entry +1: mcr p15, 0, r0, c7, c6, 1 @ invalidate D entry + add r0, r0, #CACHE_DLINESIZE + cmp r0, r1 + blo 1b +#endif + mcr p15, 0, ip, c7, c10, 4 @ drain WB + ret lr + +/* + * dma_clean_range(start, end) + * + * Clean the specified virtual address range. + * + * - start - virtual start address + * - end - virtual end address + * + * (same as v4wb) + */ +arm1020e_dma_clean_range: + mov ip, #0 +#ifndef CONFIG_CPU_DCACHE_DISABLE + bic r0, r0, #CACHE_DLINESIZE - 1 +1: mcr p15, 0, r0, c7, c10, 1 @ clean D entry + add r0, r0, #CACHE_DLINESIZE + cmp r0, r1 + blo 1b +#endif + mcr p15, 0, ip, c7, c10, 4 @ drain WB + ret lr + +/* + * dma_flush_range(start, end) + * + * Clean and invalidate the specified virtual address range. + * + * - start - virtual start address + * - end - virtual end address + */ +ENTRY(arm1020e_dma_flush_range) + mov ip, #0 +#ifndef CONFIG_CPU_DCACHE_DISABLE + bic r0, r0, #CACHE_DLINESIZE - 1 +1: mcr p15, 0, r0, c7, c14, 1 @ clean+invalidate D entry + add r0, r0, #CACHE_DLINESIZE + cmp r0, r1 + blo 1b +#endif + mcr p15, 0, ip, c7, c10, 4 @ drain WB + ret lr + +/* + * dma_map_area(start, size, dir) + * - start - kernel virtual start address + * - size - size of region + * - dir - DMA direction + */ +ENTRY(arm1020e_dma_map_area) + add r1, r1, r0 + cmp r2, #DMA_TO_DEVICE + beq arm1020e_dma_clean_range + bcs arm1020e_dma_inv_range + b arm1020e_dma_flush_range +ENDPROC(arm1020e_dma_map_area) + +/* + * dma_unmap_area(start, size, dir) + * - start - kernel virtual start address + * - size - size of region + * - dir - DMA direction + */ +ENTRY(arm1020e_dma_unmap_area) + ret lr +ENDPROC(arm1020e_dma_unmap_area) + + .globl arm1020e_flush_kern_cache_louis + .equ arm1020e_flush_kern_cache_louis, arm1020e_flush_kern_cache_all + + @ define struct cpu_cache_fns (see <asm/cacheflush.h> and proc-macros.S) + define_cache_functions arm1020e + + .align 5 +ENTRY(cpu_arm1020e_dcache_clean_area) +#ifndef CONFIG_CPU_DCACHE_DISABLE + mov ip, #0 +1: mcr p15, 0, r0, c7, c10, 1 @ clean D entry + add r0, r0, #CACHE_DLINESIZE + subs r1, r1, #CACHE_DLINESIZE + bhi 1b +#endif + ret lr + +/* =============================== PageTable ============================== */ + +/* + * cpu_arm1020e_switch_mm(pgd) + * + * Set the translation base pointer to be as described by pgd. + * + * pgd: new page tables + */ + .align 5 +ENTRY(cpu_arm1020e_switch_mm) +#ifdef CONFIG_MMU +#ifndef CONFIG_CPU_DCACHE_DISABLE + mcr p15, 0, r3, c7, c10, 4 + mov r1, #0xF @ 16 segments +1: mov r3, #0x3F @ 64 entries +2: mov ip, r3, LSL #26 @ shift up entry + orr ip, ip, r1, LSL #5 @ shift in/up index + mcr p15, 0, ip, c7, c14, 2 @ Clean & Inval DCache entry + mov ip, #0 + subs r3, r3, #1 + cmp r3, #0 + bge 2b @ entries 3F to 0 + subs r1, r1, #1 + cmp r1, #0 + bge 1b @ segments 15 to 0 + +#endif + mov r1, #0 +#ifndef CONFIG_CPU_ICACHE_DISABLE + mcr p15, 0, r1, c7, c5, 0 @ invalidate I cache +#endif + mcr p15, 0, r1, c7, c10, 4 @ drain WB + mcr p15, 0, r0, c2, c0, 0 @ load page table pointer + mcr p15, 0, r1, c8, c7, 0 @ invalidate I & D TLBs +#endif + ret lr + +/* + * cpu_arm1020e_set_pte(ptep, pte) + * + * Set a PTE and flush it out + */ + .align 5 +ENTRY(cpu_arm1020e_set_pte_ext) +#ifdef CONFIG_MMU + armv3_set_pte_ext + mov r0, r0 +#ifndef CONFIG_CPU_DCACHE_DISABLE + mcr p15, 0, r0, c7, c10, 1 @ clean D entry +#endif +#endif /* CONFIG_MMU */ + ret lr + + .type __arm1020e_setup, #function +__arm1020e_setup: + mov r0, #0 + mcr p15, 0, r0, c7, c7 @ invalidate I,D caches on v4 + mcr p15, 0, r0, c7, c10, 4 @ drain write buffer on v4 +#ifdef CONFIG_MMU + mcr p15, 0, r0, c8, c7 @ invalidate I,D TLBs on v4 +#endif + adr r5, arm1020e_crval + ldmia r5, {r5, r6} + mrc p15, 0, r0, c1, c0 @ get control register v4 + bic r0, r0, r5 + orr r0, r0, r6 +#ifdef CONFIG_CPU_CACHE_ROUND_ROBIN + orr r0, r0, #0x4000 @ .R.. .... .... .... +#endif + ret lr + .size __arm1020e_setup, . - __arm1020e_setup + + /* + * R + * .RVI ZFRS BLDP WCAM + * .011 1001 ..11 0101 + */ + .type arm1020e_crval, #object +arm1020e_crval: + crval clear=0x00007f3f, mmuset=0x00003935, ucset=0x00001930 + + __INITDATA + @ define struct processor (see <asm/proc-fns.h> and proc-macros.S) + define_processor_functions arm1020e, dabort=v4t_early_abort, pabort=legacy_pabort + + .section ".rodata" + + string cpu_arch_name, "armv5te" + string cpu_elf_name, "v5" + string cpu_arm1020e_name, "ARM1020E" + + .align + + .section ".proc.info.init", "a" + + .type __arm1020e_proc_info,#object +__arm1020e_proc_info: + .long 0x4105a200 @ ARM 1020TE (Architecture v5TE) + .long 0xff0ffff0 + .long PMD_TYPE_SECT | \ + PMD_BIT4 | \ + PMD_SECT_AP_WRITE | \ + PMD_SECT_AP_READ + .long PMD_TYPE_SECT | \ + PMD_BIT4 | \ + PMD_SECT_AP_WRITE | \ + PMD_SECT_AP_READ + initfn __arm1020e_setup, __arm1020e_proc_info + .long cpu_arch_name + .long cpu_elf_name + .long HWCAP_SWP | HWCAP_HALF | HWCAP_THUMB | HWCAP_EDSP + .long cpu_arm1020e_name + .long arm1020e_processor_functions + .long v4wbi_tlb_fns + .long v4wb_user_fns + .long arm1020e_cache_fns + .size __arm1020e_proc_info, . - __arm1020e_proc_info |