diff options
Diffstat (limited to 'arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts')
| -rw-r--r-- | arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts | 143 |
1 files changed, 143 insertions, 0 deletions
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts new file mode 100644 index 000000000..22530ace1 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts @@ -0,0 +1,143 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2017 Jagan Teki <jteki@openedev.com> + +/dts-v1/; + +#include "sun50i-h5.dtsi" + +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "OrangePi Zero Plus2"; + compatible = "xunlong,orangepi-zero-plus2", "allwinner,sun50i-h5"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + label = "orangepi:green:pwr"; + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + led-1 { + label = "orangepi:red:status"; + gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; + }; + }; + + reg_vcc3v3: vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */ + post-power-on-delay-ms = <200>; + }; +}; + +&de { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&mmc0 { + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&mmc1 { + vmmc-supply = <®_vcc3v3>; + vqmmc-supply = <®_vcc3v3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&r_pio>; + interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>; /* PL7 */ + interrupt-names = "host-wake"; + }; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_8bit_pins>; + vmmc-supply = <®_vcc3v3>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pa_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; + status = "okay"; +}; + +&usb_otg { + /* + * According to schematics CN1 MicroUSB port can be used to take + * external 5V to power up the board VBUS. On the contrary CN1 MicroUSB + * port cannot provide power externally even if the board is powered + * via GPIO pins. It thus makes sense to force peripheral mode. + */ + dr_mode = "peripheral"; + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; |