diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi')
| -rw-r--r-- | arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi | 213 |
1 files changed, 213 insertions, 0 deletions
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi new file mode 100644 index 000000000..13339b723 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi @@ -0,0 +1,213 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Lazor board device tree source + * + * Copyright 2020 Google LLC. + */ + +/* This file must be included after sc7180-trogdor.dtsi */ +#include <arm/cros-ec-keyboard.dtsi> + +&ap_sar_sensor { + semtech,cs0-ground; + semtech,combined-sensors = <3>; + semtech,resolution = "fine"; + semtech,startup-sensor = <0>; + semtech,proxraw-strength = <8>; + semtech,avg-pos-strength = <64>; +}; + +&ap_tp_i2c { + status = "okay"; +}; + +/* + * Lazor is stuffed with a 47k NTC as charger thermistor which currently is + * not supported by the PM6150 ADC driver. Disable the charger thermal zone + * to avoid using bogus temperature values. + */ +&charger_thermal { + status = "disabled"; +}; + +ap_ts_pen_1v8: &i2c4 { + status = "okay"; + clock-frequency = <400000>; + + ap_ts: touchscreen@10 { + compatible = "hid-over-i2c"; + reg = <0x10>; + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_l>, <&ts_reset_l>; + + interrupt-parent = <&tlmm>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; + + post-power-on-delay-ms = <20>; + hid-descr-addr = <0x0001>; + + vdd-supply = <&pp3300_ts>; + }; +}; + +&panel { + compatible = "boe,nv133fhm-n62"; +}; + +&pm6150_adc { + /delete-node/ channel@4f; +}; + +&pm6150_adc_tm { + status = "disabled"; + + /delete-node/ charger-thermistor@0; +}; + +&trackpad { + interrupts = <58 IRQ_TYPE_EDGE_FALLING>; +}; + +&wifi { + qcom,ath10k-calibration-variant = "GO_LAZOR"; +}; + +/* PINCTRL - modifications to sc7180-trogdor.dtsi */ + +&trackpad_int_1v8_odl { + pins = "gpio58"; +}; + +&ts_reset_l { + /* This pin is not connected on -rev0, pull up to park. */ + /delete-property/bias-disable; + bias-pull-up; +}; + +/* PINCTRL - board-specific pinctrl */ + +&tlmm { + gpio-line-names = "ESIM_MISO", + "ESIM_MOSI", + "ESIM_CLK", + "ESIM_CS_L", + "", + "", + "AP_TP_I2C_SDA", + "AP_TP_I2C_SCL", + "TS_RESET_L", + "TS_INT_L", + "", + "EDP_BRIJ_IRQ", + "AP_EDP_BKLTEN", + "AP_RAM_ID2", + "", + "EDP_BRIJ_I2C_SDA", + "EDP_BRIJ_I2C_SCL", + "HUB_RST_L", + "", + "AP_RAM_ID1", + "AP_SKU_ID2", + "", + "", + "AMP_EN", + "P_SENSOR_INT_L", + "AP_SAR_SENSOR_SDA", + "AP_SAR_SENSOR_SCL", + "", + "HP_IRQ", + "AP_RAM_ID0", + "EN_PP3300_DX_EDP", + "AP_BRD_ID2", + "BRIJ_SUSPEND", + "AP_BRD_ID0", + "AP_H1_SPI_MISO", + "AP_H1_SPI_MOSI", + "AP_H1_SPI_CLK", + "AP_H1_SPI_CS_L", + "", + "", + "", + "", + "H1_AP_INT_ODL", + "", + "UART_AP_TX_DBG_RX", + "UART_DBG_TX_AP_RX", + "HP_I2C_SDA", + "HP_I2C_SCL", + "FORCED_USB_BOOT", + "", + "", + "AMP_DIN", + "", + "HP_BCLK", + "HP_LRCLK", + "HP_DOUT", + "HP_DIN", + "HP_MCLK", + "TRACKPAD_INT_1V8_ODL", + "AP_EC_SPI_MISO", + "AP_EC_SPI_MOSI", + "AP_EC_SPI_CLK", + "AP_EC_SPI_CS_L", + "AP_SPI_CLK", + "AP_SPI_MOSI", + "AP_SPI_MISO", + /* + * AP_FLASH_WP_L is crossystem ABI. Schematics + * call it BIOS_FLASH_WP_L. + */ + "AP_FLASH_WP_L", + "DBG_SPI_HOLD_L", + "AP_SPI_CS0_L", + "", + "", + "", + "", + "", + "", + "UIM2_DATA", + "UIM2_CLK", + "UIM2_RST", + "UIM2_PRESENT", + "UIM1_DATA", + "UIM1_CLK", + "UIM1_RST", + "", + "EN_PP3300_CODEC", + "EN_PP3300_HUB", + "", + "", + "", + "", + "", + "AP_SKU_ID1", + "AP_RST_REQ", + "", + "AP_BRD_ID1", + "AP_EC_INT_L", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "EDP_BRIJ_EN", + "AP_SKU_ID0", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "AP_TS_PEN_I2C_SDA", + "AP_TS_PEN_I2C_SCL", + "DP_HOT_PLUG_DET", + "EC_IN_RW_ODL"; +}; |