diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi')
| -rw-r--r-- | arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 1567 |
1 files changed, 1567 insertions, 0 deletions
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi new file mode 100644 index 000000000..5a33e16a8 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi @@ -0,0 +1,1567 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Trogdor device tree source (common between revisions) + * + * Copyright 2019 Google LLC. + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include <dt-bindings/sound/sc7180-lpass.h> + +#include "sc7180.dtsi" +#include "sc7180-firmware-tfa.dtsi" +/* PMICs depend on spmi_bus label and so must come after sc7180.dtsi */ +#include "pm6150.dtsi" +#include "pm6150l.dtsi" + +/ { + thermal-zones { + charger_thermal: charger-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&pm6150_adc_tm 0>; + + trips { + charger-crit { + temperature = <125000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + }; +}; + +/* + * Reserved memory changes + * + * Delete all unused memory nodes and define the peripheral memory regions + * required by the board dts. + */ + +/delete-node/ &hyp_mem; +/delete-node/ &ipa_fw_mem; +/delete-node/ &xbl_mem; +/delete-node/ &aop_mem; +/delete-node/ &sec_apps_mem; +/delete-node/ &tz_mem; + +/* Increase the size from 2MB to 8MB */ +&rmtfs_mem { + reg = <0x0 0x94600000 0x0 0x800000>; +}; + +/ { + reserved-memory { + atf_mem: memory@80b00000 { + reg = <0x0 0x80b00000 0x0 0x100000>; + no-map; + }; + + mpss_mem: memory@86000000 { + reg = <0x0 0x86000000 0x0 0x2000000>; + no-map; + }; + + venus_mem: memory@8f600000 { + reg = <0 0x8f600000 0 0x500000>; + no-map; + }; + + wlan_mem: memory@94100000 { + reg = <0x0 0x94100000 0x0 0x200000>; + no-map; + }; + + mba_mem: memory@94400000 { + reg = <0x0 0x94400000 0x0 0x200000>; + no-map; + }; + + mdata_mem: mpss-metadata { + alloc-ranges = <0x0 0xa0000000 0x0 0x20000000>; + size = <0x0 0x4000>; + no-map; + }; + }; + + aliases { + bluetooth0 = &bluetooth; + hsuart0 = &uart3; + serial0 = &uart8; + wifi0 = &wifi; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + /* FIXED REGULATORS - parents above children */ + + /* This is the top level supply and variable voltage */ + ppvar_sys: ppvar-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "ppvar_sys"; + regulator-always-on; + regulator-boot-on; + }; + + /* This divides ppvar_sys by 2, so voltage is variable */ + src_vph_pwr: src-vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "src_vph_pwr"; + + /* EC turns on with switchcap_on; always on for AP */ + regulator-always-on; + regulator-boot-on; + + vin-supply = <&ppvar_sys>; + }; + + pp5000_a: pp5000-a-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp5000_a"; + + /* EC turns on with en_pp5000_a; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + vin-supply = <&ppvar_sys>; + }; + + pp3300_a: pp3300-a-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp3300_a"; + + /* EC turns on with en_pp3300_a; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + /* + * Actually should be pp3300 but that's practically an alias for + * pp3300_a so we use pp3300's vin-supply here to avoid one more + * node. + */ + vin-supply = <&ppvar_sys>; + }; + + pp1800_ec: + pp1800_sensors: + pp1800_ldo: pp1800-ldo-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp1800_ldo"; + + /* EC turns on with hibernate_l; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + /* + * Actually should be pp1800_h1 but we don't have any need to + * model that so we use the parent of pp1800_h1. + */ + vin-supply = <&pp3300_a>; + }; + + pp1800_uf_cam: pp1800-uf-cam-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp1800_uf_cam"; + status = "disabled"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&uf_cam_en>; + + vin-supply = <&pp1800_ldo>; + regulator-enable-ramp-delay = <1000>; + }; + + pp1800_wf_cam: pp1800-wf-cam-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp1800_wf_cam"; + status = "disabled"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&wf_cam_en>; + + vin-supply = <&pp1800_ldo>; + regulator-enable-ramp-delay = <1000>; + }; + + pp2800_uf_cam: pp2800-uf-cam-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp2800_uf_cam"; + status = "disabled"; + + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + + gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>; + enable-active-high; + /* + * The pinconf can only be referenced once so we put it on the + * first regulator and comment it out here. + * pinctrl-names = "default"; + * pinctrl-0 = <&uf_cam_en>; + */ + + vin-supply = <&pp3300_a>; + }; + + pp2800_vcm_wf_cam: + pp2800_wf_cam: pp2800-wf-cam-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp2800_wf_cam"; + status = "disabled"; + + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + + gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + /* + * The pinconf can only be referenced once so we put it on the + * first regulator and comment it out here. + * pinctrl-names = "default"; + * pinctrl-0 = <&wf_cam_en>; + */ + + vin-supply = <&pp3300_a>; + }; + + pp3300_audio: + pp3300_codec: pp3300-codec-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp3300_codec"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 83 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&en_pp3300_codec>; + + vin-supply = <&pp3300_a>; + }; + + pp3300_dx_edp: + pp3300_ts: pp3300-dx-edp-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp3300_dx_edp"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 30 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&en_pp3300_dx_edp>; + + vin-supply = <&pp3300_a>; + }; + + pp3300_fp_tp: pp3300-fp-tp-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp3300_fp_tp"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + /* AP turns on with PP1800_VIO_OUT; always on for AP */ + regulator-always-on; + regulator-boot-on; + + vin-supply = <&pp3300_a>; + }; + + pp3300_hub: pp3300-hub-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp3300_hub"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&en_pp3300_hub>; + + /* The BIOS leaves this regulator on */ + regulator-boot-on; + + vin-supply = <&pp3300_a>; + }; + + /* BOARD-SPECIFIC TOP LEVEL NODES */ + + backlight: backlight { + compatible = "pwm-backlight"; + + /* The panels don't seem to like anything below ~ 5% */ + brightness-levels = < + 196 256 324 400 484 576 676 784 900 1024 1156 1296 + 1444 1600 1764 1936 2116 2304 2500 2704 2916 3136 + 3364 3600 3844 4096 + >; + num-interpolated-steps = <64>; + default-brightness-level = <951>; + + pwms = <&cros_ec_pwm 1>; + enable-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + power-supply = <&ppvar_sys>; + pinctrl-names = "default"; + pinctrl-0 = <&ap_edp_bklten>; + }; + + gpio_keys: gpio-keys { + compatible = "gpio-keys"; + status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&pen_pdct_l>; + + pen_insert: switch-pen-insert { + label = "Pen Insert"; + + /* Insert = low, eject = high */ + gpios = <&tlmm 52 GPIO_ACTIVE_LOW>; + linux,code = <SW_PEN_INSERTED>; + linux,input-type = <EV_SW>; + wakeup-event-action = <EV_ACT_DEASSERTED>; + wakeup-source; + }; + }; + + max98360a: audio-codec-0 { + compatible = "maxim,max98360a"; + pinctrl-names = "default"; + pinctrl-0 = <&_en>; + sdmode-gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>; + #sound-dai-cells = <0>; + }; + + pwmleds { + compatible = "pwm-leds"; + keyboard_backlight: led-0 { + status = "disabled"; + label = "cros_ec::kbd_backlight"; + function = LED_FUNCTION_KBD_BACKLIGHT; + pwms = <&cros_ec_pwm 0>; + max-brightness = <1023>; + }; + }; + + sound: sound { + compatible = "google,sc7180-trogdor"; + model = "sc7180-rt5682-max98357a-1mic"; + + audio-routing = + "Headphone Jack", "HPOL", + "Headphone Jack", "HPOR"; + + #address-cells = <1>; + #size-cells = <0>; + + dai-link@0 { + link-name = "MultiMedia0"; + reg = <MI2S_PRIMARY>; + cpu { + sound-dai = <&lpass_cpu MI2S_PRIMARY>; + }; + + sound_multimedia0_codec: codec { + sound-dai = <&alc5682 0 /* aif1 */>; + }; + }; + + dai-link@1 { + link-name = "MultiMedia1"; + reg = <MI2S_SECONDARY>; + cpu { + sound-dai = <&lpass_cpu MI2S_SECONDARY>; + }; + + sound_multimedia1_codec: codec { + sound-dai = <&max98360a>; + }; + }; + + dai-link@5 { + link-name = "MultiMedia2"; + reg = <LPASS_DP_RX>; + cpu { + sound-dai = <&lpass_cpu LPASS_DP_RX>; + }; + + codec { + sound-dai = <&mdss_dp>; + }; + }; + }; +}; + +&qfprom { + vcc-supply = <&pp1800_l11a>; +}; + +&qspi { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data0>, <&qspi_data1>; + pinctrl-1 = <&qspi_sleep>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + + spi-max-frequency = <37500000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm6150-rpmh-regulators"; + qcom,pmic-id = "a"; + + vddpx_1: + vdd2: + pp1125_s1a: smps1 { + regulator-min-microvolt = <1128000>; + regulator-max-microvolt = <1128000>; + }; + + vdd_qlink_lv: + vdd_qlink_lv_ck: + vdd_qusb_hs0_core: + vdd_ufs1_core: + vdda_mipi_csi0_0p9: + vdda_mipi_csi1_0p9: + vdda_mipi_csi2_0p9: + vdda_mipi_csi3_0p9: + vdda_mipi_dsi0_pll: + vdda_pll_cc_ebi01: + vdda_qrefs_0p9: + vdda_usb_ss_dp_core: + pp900_l4a: ldo4 { + regulator-min-microvolt = <824000>; + regulator-max-microvolt = <928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_cx_wlan: + pp800_l9a: ldo9 { + regulator-min-microvolt = <488000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd1: + vddpx_3: + vddpx_7: + vio_in: + pp1800_l10a: ldo10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_qfprom: + vdda_apc1_cs_1p8: + vdda_qrefs_1p8: + vdda_qusb_hs0_1p8: + vddpx_11: + vreg_bb_clk: + pp1800_l11a: ldo11 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + mcp_vccq: + pp1800_l12a_r: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + /* + * On trogdor this needs to match l10a since we use it to + * give power to things like SPI flash which communicate back + * on lines powered by l10a. Thus we force to 1.8V. + */ + pp1800_l13a: ldo13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-always-on; + regulator-boot-on; + }; + + pp1800_prox: + pp1800_l14a: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp1800_alc5682: + pp1800_l15a: ldo15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_qusb_hs0_3p1: + vdd_pdphy: + pp3100_l17a: ldo17 { + regulator-min-microvolt = <2920000>; + regulator-max-microvolt = <3232000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp1800_pen: + pp1800_l18a: ldo18 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + mcp_vcc: + pp2850_l19a: ldo19 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm6150l-rpmh-regulators"; + qcom,pmic-id = "c"; + + pp1300_s8c: smps8 { + regulator-min-microvolt = <1120000>; + regulator-max-microvolt = <1408000>; + }; + + pp1800_l1c: ldo1 { + regulator-min-microvolt = <1616000>; + regulator-max-microvolt = <1984000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_wcss_adc_dac: + pp1300_l2c: ldo2 { + regulator-min-microvolt = <1168000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp1200_brij: + vdd_ufs1_1p2: + vdda_csi0_1p25: + vdda_csi1_1p25: + vdda_csi2_1p25: + vdda_csi3_1p25: + vdda_hv_ebi0: + vdda_mipi_dsi0_1p2: + vdda_usb_ss_dp_1p2: + vddpx_10: + pp1200_l3c: ldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_2: + ppvar_l6c: ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2952000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp3300_l7c: ldo7 { + regulator-min-microvolt = <3304000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp1800_brij_vccio: + pp1800_edp_vpll: + pp1800_l8c: ldo8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp2950_l9c: ldo9 { + regulator-min-microvolt = <2952000>; + regulator-max-microvolt = <2952000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp3300_l10c: ldo10 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3400000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp3300_l11c: ldo11 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3400000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + src_vreg_bob: bob { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + }; + }; +}; + +ap_ec_spi: &spi6 { + status = "okay"; + cros_ec: ec@0 { + compatible = "google,cros-ec-spi"; + reg = <0>; + interrupt-parent = <&tlmm>; + interrupts = <94 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ap_ec_int_l>; + spi-max-frequency = <3000000>; + + cros_ec_pwm: pwm { + compatible = "google,cros-ec-pwm"; + #pwm-cells = <1>; + }; + + i2c_tunnel: i2c-tunnel { + compatible = "google,cros-ec-i2c-tunnel"; + google,remote-bus = <0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + typec { + compatible = "google,cros-ec-typec"; + #address-cells = <1>; + #size-cells = <0>; + + usb_c0: connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + label = "left"; + power-role = "dual"; + data-role = "host"; + try-power-role = "source"; + }; + + usb_c1: connector@1 { + compatible = "usb-c-connector"; + reg = <1>; + label = "right"; + power-role = "dual"; + data-role = "host"; + try-power-role = "source"; + }; + }; + }; +}; + +ap_h1_spi: &spi0 { + status = "okay"; + cr50: tpm@0 { + compatible = "google,cr50"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&h1_ap_int_odl>; + spi-max-frequency = <800000>; + interrupt-parent = <&tlmm>; + interrupts = <42 IRQ_TYPE_EDGE_RISING>; + }; +}; + +&camcc { + status = "disabled"; +}; + +ap_sar_sensor_i2c: &i2c5 { + clock-frequency = <400000>; + + ap_sar_sensor: proximity@28 { + compatible = "semtech,sx9310"; + reg = <0x28>; + #io-channel-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&p_sensor_int_l>; + + interrupt-parent = <&tlmm>; + interrupts = <24 IRQ_TYPE_LEVEL_LOW>; + + vdd-supply = <&pp3300_a>; + svdd-supply = <&pp1800_prox>; + + label = "proximity-wifi"; + }; +}; + +ap_tp_i2c: &i2c7 { + clock-frequency = <400000>; + + trackpad: trackpad@15 { + compatible = "elan,ekth3000"; + reg = <0x15>; + pinctrl-names = "default"; + pinctrl-0 = <&tp_int_odl>; + + interrupt-parent = <&tlmm>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + + vcc-supply = <&pp3300_fp_tp>; + + wakeup-source; + }; +}; + +hp_i2c: &i2c9 { + status = "okay"; + clock-frequency = <400000>; + + alc5682: codec@1a { + compatible = "realtek,rt5682i"; + reg = <0x1a>; + pinctrl-names = "default"; + pinctrl-0 = <&hp_irq>; + + #sound-dai-cells = <1>; + + interrupt-parent = <&tlmm>; + /* + * This will get ignored because the interrupt type + * is set in rt5682.c. + */ + interrupts = <28 IRQ_TYPE_EDGE_BOTH>; + + AVDD-supply = <&pp1800_alc5682>; + DBVDD-supply = <&pp1800_alc5682>; + LDO1-IN-supply = <&pp1800_alc5682>; + MICVDD-supply = <&pp3300_codec>; + VBAT-supply = <&pp3300_audio>; + + realtek,dmic1-data-pin = <1>; + realtek,dmic1-clk-pin = <1>; + realtek,jd-src = <1>; + }; +}; + +&lpasscc { + status = "okay"; +}; + +&lpass_cpu { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&sec_mi2s_active>, <&pri_mi2s_active>, <&pri_mi2s_mclk_active>; + + #address-cells = <1>; + #size-cells = <0>; + + dai-link@0 { + reg = <MI2S_PRIMARY>; + qcom,playback-sd-lines = <1>; + qcom,capture-sd-lines = <0>; + }; + + secondary_mi2s: dai-link@1 { + reg = <MI2S_SECONDARY>; + qcom,playback-sd-lines = <0>; + }; + + dai-link@5 { + reg = <LPASS_DP_RX>; + }; +}; + +&lpass_hm { + status = "okay"; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dp { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dp_hot_plug_det>; +}; + +&mdss_dp_out { + data-lanes = <0 1>; + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>; +}; + +&mdss_dsi0 { + status = "okay"; + vdda-supply = <&vdda_mipi_dsi0_1p2>; +}; + +&mdss_dsi0_out { + data-lanes = <0 1 2 3>; +}; + +&mdss_dsi0_phy { + status = "okay"; + vdds-supply = <&vdda_mipi_dsi0_pll>; +}; + +&pm6150_adc { + channel@4f { + reg = <ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + label = "charger_therm"; + }; +}; + +&pm6150_adc_tm { + status = "okay"; + + charger-thermistor@0 { + reg = <0>; + io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + +&pm6150_pon { + status = "disabled"; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&remoteproc_mpss { + status = "okay"; + compatible = "qcom,sc7180-mss-pil"; + reg = <0 0x04080000 0 0x4040>, <0 0x04180000 0 0x48>; + reg-names = "qdsp6", "rmb"; + + clocks = <&gcc GCC_MSS_CFG_AHB_CLK>, + <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>, + <&gcc GCC_MSS_NAV_AXI_CLK>, + <&gcc GCC_MSS_SNOC_AXI_CLK>, + <&gcc GCC_MSS_MFAB_AXIS_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "bus", "nav", "snoc_axi", "mnoc_axi", "xo"; + + iommus = <&apps_smmu 0x461 0x0>, <&apps_smmu 0x444 0x3>; + memory-region = <&mba_mem>, <&mpss_mem>, <&mdata_mem>; + + /* This gets overridden for SKUs with LTE support. */ + firmware-name = "qcom/sc7180-trogdor/modem-nolte/mba.mbn", + "qcom/sc7180-trogdor/modem-nolte/qdsp6sw.mbn"; + + resets = <&aoss_reset AOSS_CC_MSS_RESTART>, + <&pdc_reset PDC_MODEM_SYNC_RESET>; + reset-names = "mss_restart", "pdc_reset"; + + qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>; + qcom,spare-regs = <&tcsr_regs_2 0xb3e4>; +}; + +&scm { + /* TF-A firmware maps memory cached so mark dma-coherent to match. */ + dma-coherent; +}; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_on>; + pinctrl-1 = <&sdc1_off>; + vmmc-supply = <&mcp_vcc>; + vqmmc-supply = <&mcp_vccq>; +}; + +&sdhc_2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_on>; + pinctrl-1 = <&sdc2_off>; + vmmc-supply = <&pp2950_l9c>; + vqmmc-supply = <&ppvar_l6c>; + + cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>; +}; + +&spi0 { + pinctrl-0 = <&qup_spi0_spi>, <&qup_spi0_cs_gpio>; + cs-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>; +}; + +&spi6 { + pinctrl-0 = <&qup_spi6_spi>, <&qup_spi6_cs_gpio>; + cs-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; +}; + +ap_spi_fp: &spi10 { + pinctrl-0 = <&qup_spi10_spi>, <&qup_spi10_cs_gpio>; + cs-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>; + + cros_ec_fp: ec@0 { + compatible = "google,cros-ec-fp", "google,cros-ec-spi"; + reg = <0>; + interrupt-parent = <&tlmm>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&fp_to_ap_irq_l>, <&fp_rst_l>, <&fpmcu_boot0>; + boot0-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>; + reset-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; + spi-max-frequency = <3000000>; + vdd-supply = <&pp3300_fp_tp>; + }; +}; + +#include <arm/cros-ec-sbs.dtsi> + +&uart3 { + status = "okay"; + + /delete-property/interrupts; + interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>, + <&tlmm 41 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default", "sleep"; + pinctrl-1 = <&qup_uart3_sleep>; + + bluetooth: bluetooth { + compatible = "qcom,wcn3991-bt"; + vddio-supply = <&pp1800_l10a>; + vddxo-supply = <&pp1800_l1c>; + vddrf-supply = <&pp1300_l2c>; + vddch0-supply = <&pp3300_l10c>; + max-speed = <3200000>; + }; +}; + +&uart8 { + status = "okay"; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "host"; + #address-cells = <1>; + #size-cells = <0>; + + /* 2.x hub on port 1 */ + usb_hub_2_x: hub@1 { + compatible = "usbbda,5411"; + reg = <1>; + vdd-supply = <&pp3300_hub>; + peer-hub = <&usb_hub_3_x>; + }; + + /* 3.x hub on port 2 */ + usb_hub_3_x: hub@2 { + compatible = "usbbda,411"; + reg = <2>; + vdd-supply = <&pp3300_hub>; + peer-hub = <&usb_hub_2_x>; + }; +}; + +&usb_1_hsphy { + status = "okay"; + vdd-supply = <&vdd_qusb_hs0_core>; + vdda-pll-supply = <&vdda_qusb_hs0_1p8>; + vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; + qcom,imp-res-offset-value = <8>; + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>; + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; + qcom,bias-ctrl-value = <0x22>; + qcom,charge-ctrl-value = <3>; + qcom,hsdisc-trim-value = <0>; +}; + +&usb_1_qmpphy { + status = "okay"; + vdda-phy-supply = <&vdda_usb_ss_dp_1p2>; + vdda-pll-supply = <&vdda_usb_ss_dp_core>; +}; + +&venus { + video-firmware { + iommus = <&apps_smmu 0x0c42 0x0>; + }; +}; + +&wifi { + status = "okay"; + vdd-0.8-cx-mx-supply = <&vdd_cx_wlan>; + vdd-1.8-xo-supply = <&pp1800_l1c>; + vdd-1.3-rfa-supply = <&pp1300_l2c>; + vdd-3.3-ch0-supply = <&pp3300_l10c>; + vdd-3.3-ch1-supply = <&pp3300_l11c>; + + wifi-firmware { + iommus = <&apps_smmu 0xc2 0x1>; + }; +}; + +/* PINCTRL - additions to nodes defined in sc7180.dtsi */ + +&dp_hot_plug_det { + bias-disable; +}; + +&pri_mi2s_active { + drive-strength = <2>; + bias-pull-down; +}; + +&pri_mi2s_mclk_active { + drive-strength = <2>; + bias-pull-down; +}; + +&qspi_cs0 { + bias-disable; /* External pullup */ +}; + +&qspi_clk { + drive-strength = <8>; + bias-disable; /* Rely on Cr50 internal pulldown */ +}; + +&qspi_data0 { + bias-disable; /* Rely on Cr50 internal pulldown */ +}; + +&qspi_data1 { + bias-pull-down; +}; + +&qup_i2c2_default { + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; +}; + +&qup_i2c4_default { + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; +}; + +&qup_i2c5_default { + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; +}; + +&qup_i2c7_default { + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; +}; + +&qup_i2c9_default { + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; +}; + +&qup_spi0_spi { + drive-strength = <2>; + bias-disable; +}; + +&qup_spi0_cs_gpio { + drive-strength = <2>; + bias-disable; +}; + +&qup_spi6_spi { + drive-strength = <2>; + bias-disable; +}; + +&qup_spi6_cs_gpio { + drive-strength = <2>; + bias-disable; +}; + +&qup_spi10_spi { + drive-strength = <2>; + bias-disable; +}; + +&qup_spi10_cs_gpio { + drive-strength = <2>; + bias-disable; +}; + +&qup_uart3_cts { + /* + * Configure a pull-down on CTS to match the pull of + * the Bluetooth module. + */ + bias-pull-down; +}; + +&qup_uart3_rts { + /* We'll drive RTS, so no pull */ + drive-strength = <2>; + bias-disable; +}; + +&qup_uart3_tx { + /* We'll drive TX, so no pull */ + drive-strength = <2>; + bias-disable; +}; + +&qup_uart3_rx { + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module is + * in tri-state (module powered off or not driving the + * signal yet). + */ + bias-pull-up; +}; + +&qup_uart8_tx { + drive-strength = <2>; + bias-disable; +}; + +&qup_uart8_rx { + drive-strength = <2>; + bias-pull-up; +}; + +&sec_mi2s_active { + drive-strength = <2>; + bias-pull-down; +}; + +/* PINCTRL - board-specific pinctrl */ + +&pm6150_gpios { + status = "disabled"; /* No GPIOs are connected */ +}; + +&pm6150l_gpios { + gpio-line-names = "AP_SUSPEND", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + ""; +}; + +&tlmm { + /* + * pinctrl settings for pins that have no real owners. + */ + pinctrl-names = "default"; + pinctrl-0 = <&bios_flash_wp_l>, <&ap_suspend_l_neuter>; + + amp_en: amp-en-state { + pins = "gpio23"; + function = "gpio"; + bias-pull-down; + }; + + ap_ec_int_l: ap-ec-int-l-state { + pins = "gpio94"; + function = "gpio"; + bias-pull-up; + }; + + ap_edp_bklten: ap-edp-bklten-state { + pins = "gpio12"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + + /* Force backlight to be disabled to match state at boot. */ + output-low; + }; + + ap_suspend_l_neuter: ap-suspend-l-neuter-state { + pins = "gpio27"; + function = "gpio"; + bias-disable; + }; + + bios_flash_wp_l: bios-flash-wp-l-state { + pins = "gpio66"; + function = "gpio"; + bias-disable; + }; + + edp_brij_en: edp-brij-en-state { + pins = "gpio104"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + en_pp3300_codec: en-pp3300-codec-state { + pins = "gpio83"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + en_pp3300_dx_edp: en-pp3300-dx-edp-state { + pins = "gpio30"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + en_pp3300_hub: en-pp3300-hub-state { + pins = "gpio84"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + fp_rst_l: fp-rst-l-state { + pins = "gpio22"; + function = "gpio"; + bias-disable; + drive-strength = <2>; + }; + + fp_to_ap_irq_l: fp-to-ap-irq-l-state { + pins = "gpio4"; + function = "gpio"; + + /* Has external pullup */ + bias-disable; + }; + + fpmcu_boot0: fpmcu-boot0-state { + pins = "gpio10"; + function = "gpio"; + bias-disable; + }; + + h1_ap_int_odl: h1-ap-int-odl-state { + pins = "gpio42"; + function = "gpio"; + bias-pull-up; + }; + + hp_irq: hp-irq-state { + pins = "gpio28"; + function = "gpio"; + bias-pull-up; + }; + + pen_irq_l: pen-irq-l-state { + pins = "gpio21"; + function = "gpio"; + + /* Has external pullup */ + bias-disable; + }; + + pen_pdct_l: pen-pdct-l-state-state { + pins = "gpio52"; + function = "gpio"; + + /* Has external pullup */ + bias-disable; + }; + + pen_rst_odl: pen-rst-odl-state { + pins = "gpio18"; + function = "gpio"; + bias-disable; + drive-strength = <2>; + + /* + * The pen driver doesn't currently support + * driving this reset line. By specifying + * output-high here we're relying on the fact + * that this pin has a default pulldown at boot + * (which makes sure the pen was in reset if it + * was powered) and then we set it high here to + * take it out of reset. Better would be if the + * pen driver could control this and we could + * remove "output-high" here. + */ + output-high; /* TODO: Remove this? */ + }; + + p_sensor_int_l: p-sensor-int-l-state { + pins = "gpio24"; + function = "gpio"; + + /* Has external pullup */ + bias-disable; + }; + + qspi_sleep: qspi-sleep-state { + pins = "gpio63", "gpio64", "gpio65", "gpio68"; + + /* + * When we're not actively transferring we want pins as GPIOs + * with output disabled so that the quad SPI IP block stops + * driving them. We rely on the normal pulls configured in + * the active state and don't redefine them here. Also note + * that we don't need the reverse (output-enable) in the + * normal mode since the "output-enable" only matters for + * GPIO function. + */ + function = "gpio"; + output-disable; + }; + + qup_uart3_sleep: qup-uart3-sleep-state { + cts-pins { + /* + * Configure a pull-down on CTS to match the pull of + * the Bluetooth module. + */ + pins = "gpio38"; + function = "gpio"; + bias-pull-down; + }; + + rts-pins { + /* + * Configure pull-down on RTS. As RTS is active low + * signal, pull it low to indicate the BT SoC that it + * can wakeup the system anytime from suspend state by + * pulling RX low (by sending wakeup bytes). + */ + pins = "gpio39"; + function = "gpio"; + bias-pull-down; + }; + + tx-pins { + /* + * Configure pull-up on TX when it isn't actively driven + * to prevent BT SoC from receiving garbage during sleep. + */ + pins = "gpio40"; + function = "gpio"; + bias-pull-up; + }; + + rx-pins { + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module + * is floating which may cause spurious wakeups. + */ + pins = "gpio41"; + function = "gpio"; + bias-pull-up; + }; + }; + + /* Named trackpad_int_1v8_odl on earlier revision schematics */ + trackpad_int_1v8_odl: + tp_int_odl: tp-int-odl-state { + pins = "gpio0"; + function = "gpio"; + + /* Has external pullup */ + bias-disable; + }; + + ts_int_l: ts-int-l-state { + pins = "gpio9"; + function = "gpio"; + bias-pull-up; + }; + + ts_reset_l: ts-reset-l-state { + pins = "gpio8"; + function = "gpio"; + bias-disable; + + /* + * The reset GPIO to the touchscreen takes almost 2ms to drop + * at the default drive strength. When we bump it up to 8mA it + * falls in under 500us. We want this to be fast since the Elan + * datasheet (and any drivers written based on it) talk about using + * a 500 us reset pulse. + */ + drive-strength = <8>; + }; + + sdc1_on: sdc1-on-state { + clk-pins { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd-pins { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <16>; + }; + + data-pins { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <16>; + }; + + rclk-pins { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc1_off: sdc1-off-state { + clk-pins { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <2>; + }; + + cmd-pins { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + data-pins { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <2>; + }; + + rclk-pins { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc2_on: sdc2-on-state { + clk-pins { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd-pins { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + data-pins { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>; + }; + + sd-cd-pins { + pins = "gpio69"; + function = "gpio"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_off: sdc2-off-state { + clk-pins { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <2>; + }; + + cmd-pins { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + data-pins { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <2>; + }; + + sd-cd-pins { + pins = "gpio69"; + function = "gpio"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + uf_cam_en: uf-cam-en-state { + pins = "gpio6"; + function = "gpio"; + drive-strength = <2>; + + /* External pull down */ + bias-disable; + }; + + wf_cam_en: wf-cam-en-state { + pins = "gpio7"; + function = "gpio"; + drive-strength = <2>; + + /* External pull down */ + bias-disable; + }; +}; |