summaryrefslogtreecommitdiffstats
path: root/arch/sh/boards/board-apsh4ad0a.c
diff options
context:
space:
mode:
Diffstat (limited to 'arch/sh/boards/board-apsh4ad0a.c')
-rw-r--r--arch/sh/boards/board-apsh4ad0a.c132
1 files changed, 132 insertions, 0 deletions
diff --git a/arch/sh/boards/board-apsh4ad0a.c b/arch/sh/boards/board-apsh4ad0a.c
new file mode 100644
index 0000000000..fa031a16c9
--- /dev/null
+++ b/arch/sh/boards/board-apsh4ad0a.c
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ALPHAPROJECT AP-SH4AD-0A Support.
+ *
+ * Copyright (C) 2010 ALPHAPROJECT Co.,Ltd.
+ * Copyright (C) 2010 Matt Fleming
+ * Copyright (C) 2010 Paul Mundt
+ */
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
+#include <linux/smsc911x.h>
+#include <linux/irq.h>
+#include <linux/clk.h>
+#include <asm/machvec.h>
+#include <linux/sizes.h>
+
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+ REGULATOR_SUPPLY("vddvario", "smsc911x"),
+ REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
+static struct resource smsc911x_resources[] = {
+ [0] = {
+ .name = "smsc911x-memory",
+ .start = 0xA4000000,
+ .end = 0xA4000000 + SZ_256 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .name = "smsc911x-irq",
+ .start = evt2irq(0x200),
+ .end = evt2irq(0x200),
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct smsc911x_platform_config smsc911x_config = {
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+ .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+ .flags = SMSC911X_USE_16BIT,
+ .phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
+static struct platform_device smsc911x_device = {
+ .name = "smsc911x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(smsc911x_resources),
+ .resource = smsc911x_resources,
+ .dev = {
+ .platform_data = &smsc911x_config,
+ },
+};
+
+static struct platform_device *apsh4ad0a_devices[] __initdata = {
+ &smsc911x_device,
+};
+
+static int __init apsh4ad0a_devices_setup(void)
+{
+ regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
+ return platform_add_devices(apsh4ad0a_devices,
+ ARRAY_SIZE(apsh4ad0a_devices));
+}
+device_initcall(apsh4ad0a_devices_setup);
+
+static int apsh4ad0a_mode_pins(void)
+{
+ int value = 0;
+
+ /* These are the factory default settings of SW1 and SW2.
+ * If you change these dip switches then you will need to
+ * adjust the values below as well.
+ */
+ value |= MODE_PIN0; /* Clock Mode 3 */
+ value |= MODE_PIN1;
+ value &= ~MODE_PIN2;
+ value &= ~MODE_PIN3;
+ value &= ~MODE_PIN4; /* 16-bit Area0 bus width */
+ value |= MODE_PIN5;
+ value |= MODE_PIN6;
+ value |= MODE_PIN7; /* Normal mode */
+ value |= MODE_PIN8; /* Little Endian */
+ value |= MODE_PIN9; /* Crystal resonator */
+ value &= ~MODE_PIN10; /* 29-bit address mode */
+ value &= ~MODE_PIN11; /* PCI-E Root port */
+ value &= ~MODE_PIN12; /* 4 lane + 1 lane */
+ value |= MODE_PIN13; /* AUD Enable */
+ value &= ~MODE_PIN14; /* Normal Operation */
+
+ return value;
+}
+
+static int apsh4ad0a_clk_init(void)
+{
+ struct clk *clk;
+ int ret;
+
+ clk = clk_get(NULL, "extal");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+ ret = clk_set_rate(clk, 33333000);
+ clk_put(clk);
+
+ return ret;
+}
+
+/* Initialize the board */
+static void __init apsh4ad0a_setup(char **cmdline_p)
+{
+ pr_info("Alpha Project AP-SH4AD-0A support:\n");
+}
+
+static void __init apsh4ad0a_init_irq(void)
+{
+ plat_irq_setup_pins(IRQ_MODE_IRQ3210);
+}
+
+/*
+ * The Machine Vector
+ */
+static struct sh_machine_vector mv_apsh4ad0a __initmv = {
+ .mv_name = "AP-SH4AD-0A",
+ .mv_setup = apsh4ad0a_setup,
+ .mv_mode_pins = apsh4ad0a_mode_pins,
+ .mv_clk_init = apsh4ad0a_clk_init,
+ .mv_init_irq = apsh4ad0a_init_irq,
+};