diff options
Diffstat (limited to 'drivers/ata/pata_pdc202xx_old.c')
-rw-r--r-- | drivers/ata/pata_pdc202xx_old.c | 391 |
1 files changed, 391 insertions, 0 deletions
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c new file mode 100644 index 0000000000..a32723e463 --- /dev/null +++ b/drivers/ata/pata_pdc202xx_old.c @@ -0,0 +1,391 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * pata_pdc202xx_old.c - Promise PDC202xx PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@lxorguk.ukuu.org.uk> + * (C) 2007,2009,2010 Bartlomiej Zolnierkiewicz + * + * Based in part on linux/drivers/ide/pci/pdc202xx_old.c + * + * First cut with LBA48/ATAPI + * + * TODO: + * Channel interlock/reset on both required ? + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_pdc202xx_old" +#define DRV_VERSION "0.4.3" + +static int pdc2026x_cable_detect(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u16 cis; + + pci_read_config_word(pdev, 0x50, &cis); + if (cis & (1 << (10 + ap->port_no))) + return ATA_CBL_PATA40; + return ATA_CBL_PATA80; +} + +static void pdc202xx_exec_command(struct ata_port *ap, + const struct ata_taskfile *tf) +{ + iowrite8(tf->command, ap->ioaddr.command_addr); + ndelay(400); +} + +static bool pdc202xx_irq_check(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + unsigned long master = pci_resource_start(pdev, 4); + u8 sc1d = inb(master + 0x1d); + + if (ap->port_no) { + /* + * bit 7: error, bit 6: interrupting, + * bit 5: FIFO full, bit 4: FIFO empty + */ + return sc1d & 0x40; + } else { + /* + * bit 3: error, bit 2: interrupting, + * bit 1: FIFO full, bit 0: FIFO empty + */ + return sc1d & 0x04; + } +} + +/** + * pdc202xx_configure_piomode - set chip PIO timing + * @ap: ATA interface + * @adev: ATA device + * @pio: PIO mode + * + * Called to do the PIO mode setup. Our timing registers are shared + * so a configure_dmamode call will undo any work we do here and vice + * versa + */ + +static void pdc202xx_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int port = 0x60 + 8 * ap->port_no + 4 * adev->devno; + static const u16 pio_timing[5] = { + 0x0913, 0x050C , 0x0308, 0x0206, 0x0104 + }; + u8 r_ap, r_bp; + + pci_read_config_byte(pdev, port, &r_ap); + pci_read_config_byte(pdev, port + 1, &r_bp); + r_ap &= ~0x3F; /* Preserve ERRDY_EN, SYNC_IN */ + r_bp &= ~0x1F; + r_ap |= (pio_timing[pio] >> 8); + r_bp |= (pio_timing[pio] & 0xFF); + + if (ata_pio_need_iordy(adev)) + r_ap |= 0x20; /* IORDY enable */ + if (adev->class == ATA_DEV_ATA) + r_ap |= 0x10; /* FIFO enable */ + pci_write_config_byte(pdev, port, r_ap); + pci_write_config_byte(pdev, port + 1, r_bp); +} + +/** + * pdc202xx_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the PIO mode setup. Our timing registers are shared + * but we want to set the PIO timing by default. + */ + +static void pdc202xx_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + pdc202xx_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); +} + +/** + * pdc202xx_set_dmamode - set DMA mode in chip + * @ap: ATA interface + * @adev: ATA device + * + * Load DMA cycle times into the chip ready for a DMA transfer + * to occur. + */ + +static void pdc202xx_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int port = 0x60 + 8 * ap->port_no + 4 * adev->devno; + static u8 udma_timing[6][2] = { + { 0x60, 0x03 }, /* 33 Mhz Clock */ + { 0x40, 0x02 }, + { 0x20, 0x01 }, + { 0x40, 0x02 }, /* 66 Mhz Clock */ + { 0x20, 0x01 }, + { 0x20, 0x01 } + }; + static u8 mdma_timing[3][2] = { + { 0xe0, 0x0f }, + { 0x60, 0x04 }, + { 0x60, 0x03 }, + }; + u8 r_bp, r_cp; + + pci_read_config_byte(pdev, port + 1, &r_bp); + pci_read_config_byte(pdev, port + 2, &r_cp); + + r_bp &= ~0xE0; + r_cp &= ~0x0F; + + if (adev->dma_mode >= XFER_UDMA_0) { + int speed = adev->dma_mode - XFER_UDMA_0; + r_bp |= udma_timing[speed][0]; + r_cp |= udma_timing[speed][1]; + + } else { + int speed = adev->dma_mode - XFER_MW_DMA_0; + r_bp |= mdma_timing[speed][0]; + r_cp |= mdma_timing[speed][1]; + } + pci_write_config_byte(pdev, port + 1, r_bp); + pci_write_config_byte(pdev, port + 2, r_cp); + +} + +/** + * pdc2026x_bmdma_start - DMA engine begin + * @qc: ATA command + * + * In UDMA3 or higher we have to clock switch for the duration of the + * DMA transfer sequence. + * + * Note: The host lock held by the libata layer protects + * us from two channels both trying to set DMA bits at once + */ + +static void pdc2026x_bmdma_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + struct ata_taskfile *tf = &qc->tf; + int sel66 = ap->port_no ? 0x08: 0x02; + + void __iomem *master = ap->host->ports[0]->ioaddr.bmdma_addr; + void __iomem *clock = master + 0x11; + void __iomem *atapi_reg = master + 0x20 + (4 * ap->port_no); + + u32 len; + + /* Check we keep host level locking here */ + if (adev->dma_mode > XFER_UDMA_2) + iowrite8(ioread8(clock) | sel66, clock); + else + iowrite8(ioread8(clock) & ~sel66, clock); + + /* The DMA clocks may have been trashed by a reset. FIXME: make conditional + and move to qc_issue ? */ + pdc202xx_set_dmamode(ap, qc->dev); + + /* Cases the state machine will not complete correctly without help */ + if ((tf->flags & ATA_TFLAG_LBA48) || tf->protocol == ATAPI_PROT_DMA) { + len = qc->nbytes / 2; + + if (tf->flags & ATA_TFLAG_WRITE) + len |= 0x06000000; + else + len |= 0x05000000; + + iowrite32(len, atapi_reg); + } + + /* Activate DMA */ + ata_bmdma_start(qc); +} + +/** + * pdc2026x_bmdma_stop - DMA engine stop + * @qc: ATA command + * + * After a DMA completes we need to put the clock back to 33MHz for + * PIO timings. + * + * Note: The host lock held by the libata layer protects + * us from two channels both trying to set DMA bits at once + */ + +static void pdc2026x_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + struct ata_taskfile *tf = &qc->tf; + + int sel66 = ap->port_no ? 0x08: 0x02; + /* The clock bits are in the same register for both channels */ + void __iomem *master = ap->host->ports[0]->ioaddr.bmdma_addr; + void __iomem *clock = master + 0x11; + void __iomem *atapi_reg = master + 0x20 + (4 * ap->port_no); + + /* Cases the state machine will not complete correctly */ + if (tf->protocol == ATAPI_PROT_DMA || (tf->flags & ATA_TFLAG_LBA48)) { + iowrite32(0, atapi_reg); + iowrite8(ioread8(clock) & ~sel66, clock); + } + /* Flip back to 33Mhz for PIO */ + if (adev->dma_mode > XFER_UDMA_2) + iowrite8(ioread8(clock) & ~sel66, clock); + ata_bmdma_stop(qc); + pdc202xx_set_piomode(ap, adev); +} + +/** + * pdc2026x_dev_config - device setup hook + * @adev: newly found device + * + * Perform chip specific early setup. We need to lock the transfer + * sizes to 8bit to avoid making the state engine on the 2026x cards + * barf. + */ + +static void pdc2026x_dev_config(struct ata_device *adev) +{ + adev->max_sectors = 256; +} + +static int pdc2026x_port_start(struct ata_port *ap) +{ + void __iomem *bmdma = ap->ioaddr.bmdma_addr; + if (bmdma) { + /* Enable burst mode */ + u8 burst = ioread8(bmdma + 0x1f); + iowrite8(burst | 0x01, bmdma + 0x1f); + } + return ata_bmdma_port_start(ap); +} + +/** + * pdc2026x_check_atapi_dma - Check whether ATAPI DMA can be supported for this command + * @qc: Metadata associated with taskfile to check + * + * Just say no - not supported on older Promise. + * + * LOCKING: + * None (inherited from caller). + * + * RETURNS: 0 when ATAPI DMA can be used + * 1 otherwise + */ + +static int pdc2026x_check_atapi_dma(struct ata_queued_cmd *qc) +{ + return 1; +} + +static const struct scsi_host_template pdc202xx_sht = { + ATA_BMDMA_SHT(DRV_NAME), +}; + +static struct ata_port_operations pdc2024x_port_ops = { + .inherits = &ata_bmdma_port_ops, + + .cable_detect = ata_cable_40wire, + .set_piomode = pdc202xx_set_piomode, + .set_dmamode = pdc202xx_set_dmamode, + + .sff_exec_command = pdc202xx_exec_command, + .sff_irq_check = pdc202xx_irq_check, +}; + +static struct ata_port_operations pdc2026x_port_ops = { + .inherits = &pdc2024x_port_ops, + + .check_atapi_dma = pdc2026x_check_atapi_dma, + .bmdma_start = pdc2026x_bmdma_start, + .bmdma_stop = pdc2026x_bmdma_stop, + + .cable_detect = pdc2026x_cable_detect, + .dev_config = pdc2026x_dev_config, + + .port_start = pdc2026x_port_start, + + .sff_exec_command = pdc202xx_exec_command, + .sff_irq_check = pdc202xx_irq_check, +}; + +static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static const struct ata_port_info info[3] = { + { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA2, + .port_ops = &pdc2024x_port_ops + }, + { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA4, + .port_ops = &pdc2026x_port_ops + }, + { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA5, + .port_ops = &pdc2026x_port_ops + } + + }; + const struct ata_port_info *ppi[] = { &info[id->driver_data], NULL }; + + if (dev->device == PCI_DEVICE_ID_PROMISE_20265) { + struct pci_dev *bridge = dev->bus->self; + /* Don't grab anything behind a Promise I2O RAID */ + if (bridge && bridge->vendor == PCI_VENDOR_ID_INTEL) { + if (bridge->device == PCI_DEVICE_ID_INTEL_I960) + return -ENODEV; + if (bridge->device == PCI_DEVICE_ID_INTEL_I960RM) + return -ENODEV; + } + } + return ata_pci_bmdma_init_one(dev, ppi, &pdc202xx_sht, NULL, 0); +} + +static const struct pci_device_id pdc202xx[] = { + { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20246), 0 }, + { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20262), 1 }, + { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20263), 1 }, + { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20265), 2 }, + { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20267), 2 }, + + { }, +}; + +static struct pci_driver pdc202xx_pci_driver = { + .name = DRV_NAME, + .id_table = pdc202xx, + .probe = pdc202xx_init_one, + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM_SLEEP + .suspend = ata_pci_device_suspend, + .resume = ata_pci_device_resume, +#endif +}; + +module_pci_driver(pdc202xx_pci_driver); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Promise 2024x and 20262-20267"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, pdc202xx); +MODULE_VERSION(DRV_VERSION); |