diff options
Diffstat (limited to 'drivers/bluetooth/hci_intel.c')
-rw-r--r-- | drivers/bluetooth/hci_intel.c | 1234 |
1 files changed, 1234 insertions, 0 deletions
diff --git a/drivers/bluetooth/hci_intel.c b/drivers/bluetooth/hci_intel.c new file mode 100644 index 0000000000..78afb9a348 --- /dev/null +++ b/drivers/bluetooth/hci_intel.c @@ -0,0 +1,1234 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * + * Bluetooth HCI UART driver for Intel devices + * + * Copyright (C) 2015 Intel Corporation + */ + +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/skbuff.h> +#include <linux/firmware.h> +#include <linux/module.h> +#include <linux/wait.h> +#include <linux/tty.h> +#include <linux/platform_device.h> +#include <linux/gpio/consumer.h> +#include <linux/acpi.h> +#include <linux/interrupt.h> +#include <linux/pm_runtime.h> + +#include <net/bluetooth/bluetooth.h> +#include <net/bluetooth/hci_core.h> + +#include "hci_uart.h" +#include "btintel.h" + +#define STATE_BOOTLOADER 0 +#define STATE_DOWNLOADING 1 +#define STATE_FIRMWARE_LOADED 2 +#define STATE_FIRMWARE_FAILED 3 +#define STATE_BOOTING 4 +#define STATE_LPM_ENABLED 5 +#define STATE_TX_ACTIVE 6 +#define STATE_SUSPENDED 7 +#define STATE_LPM_TRANSACTION 8 + +#define HCI_LPM_WAKE_PKT 0xf0 +#define HCI_LPM_PKT 0xf1 +#define HCI_LPM_MAX_SIZE 10 +#define HCI_LPM_HDR_SIZE HCI_EVENT_HDR_SIZE + +#define LPM_OP_TX_NOTIFY 0x00 +#define LPM_OP_SUSPEND_ACK 0x02 +#define LPM_OP_RESUME_ACK 0x03 + +#define LPM_SUSPEND_DELAY_MS 1000 + +struct hci_lpm_pkt { + __u8 opcode; + __u8 dlen; + __u8 data[]; +} __packed; + +struct intel_device { + struct list_head list; + struct platform_device *pdev; + struct gpio_desc *reset; + struct hci_uart *hu; + struct mutex hu_lock; + int irq; +}; + +static LIST_HEAD(intel_device_list); +static DEFINE_MUTEX(intel_device_list_lock); + +struct intel_data { + struct sk_buff *rx_skb; + struct sk_buff_head txq; + struct work_struct busy_work; + struct hci_uart *hu; + unsigned long flags; +}; + +static u8 intel_convert_speed(unsigned int speed) +{ + switch (speed) { + case 9600: + return 0x00; + case 19200: + return 0x01; + case 38400: + return 0x02; + case 57600: + return 0x03; + case 115200: + return 0x04; + case 230400: + return 0x05; + case 460800: + return 0x06; + case 921600: + return 0x07; + case 1843200: + return 0x08; + case 3250000: + return 0x09; + case 2000000: + return 0x0a; + case 3000000: + return 0x0b; + default: + return 0xff; + } +} + +static int intel_wait_booting(struct hci_uart *hu) +{ + struct intel_data *intel = hu->priv; + int err; + + err = wait_on_bit_timeout(&intel->flags, STATE_BOOTING, + TASK_INTERRUPTIBLE, + msecs_to_jiffies(1000)); + + if (err == -EINTR) { + bt_dev_err(hu->hdev, "Device boot interrupted"); + return -EINTR; + } + + if (err) { + bt_dev_err(hu->hdev, "Device boot timeout"); + return -ETIMEDOUT; + } + + return err; +} + +#ifdef CONFIG_PM +static int intel_wait_lpm_transaction(struct hci_uart *hu) +{ + struct intel_data *intel = hu->priv; + int err; + + err = wait_on_bit_timeout(&intel->flags, STATE_LPM_TRANSACTION, + TASK_INTERRUPTIBLE, + msecs_to_jiffies(1000)); + + if (err == -EINTR) { + bt_dev_err(hu->hdev, "LPM transaction interrupted"); + return -EINTR; + } + + if (err) { + bt_dev_err(hu->hdev, "LPM transaction timeout"); + return -ETIMEDOUT; + } + + return err; +} + +static int intel_lpm_suspend(struct hci_uart *hu) +{ + static const u8 suspend[] = { 0x01, 0x01, 0x01 }; + struct intel_data *intel = hu->priv; + struct sk_buff *skb; + + if (!test_bit(STATE_LPM_ENABLED, &intel->flags) || + test_bit(STATE_SUSPENDED, &intel->flags)) + return 0; + + if (test_bit(STATE_TX_ACTIVE, &intel->flags)) + return -EAGAIN; + + bt_dev_dbg(hu->hdev, "Suspending"); + + skb = bt_skb_alloc(sizeof(suspend), GFP_KERNEL); + if (!skb) { + bt_dev_err(hu->hdev, "Failed to alloc memory for LPM packet"); + return -ENOMEM; + } + + skb_put_data(skb, suspend, sizeof(suspend)); + hci_skb_pkt_type(skb) = HCI_LPM_PKT; + + set_bit(STATE_LPM_TRANSACTION, &intel->flags); + + /* LPM flow is a priority, enqueue packet at list head */ + skb_queue_head(&intel->txq, skb); + hci_uart_tx_wakeup(hu); + + intel_wait_lpm_transaction(hu); + /* Even in case of failure, continue and test the suspended flag */ + + clear_bit(STATE_LPM_TRANSACTION, &intel->flags); + + if (!test_bit(STATE_SUSPENDED, &intel->flags)) { + bt_dev_err(hu->hdev, "Device suspend error"); + return -EINVAL; + } + + bt_dev_dbg(hu->hdev, "Suspended"); + + hci_uart_set_flow_control(hu, true); + + return 0; +} + +static int intel_lpm_resume(struct hci_uart *hu) +{ + struct intel_data *intel = hu->priv; + struct sk_buff *skb; + + if (!test_bit(STATE_LPM_ENABLED, &intel->flags) || + !test_bit(STATE_SUSPENDED, &intel->flags)) + return 0; + + bt_dev_dbg(hu->hdev, "Resuming"); + + hci_uart_set_flow_control(hu, false); + + skb = bt_skb_alloc(0, GFP_KERNEL); + if (!skb) { + bt_dev_err(hu->hdev, "Failed to alloc memory for LPM packet"); + return -ENOMEM; + } + + hci_skb_pkt_type(skb) = HCI_LPM_WAKE_PKT; + + set_bit(STATE_LPM_TRANSACTION, &intel->flags); + + /* LPM flow is a priority, enqueue packet at list head */ + skb_queue_head(&intel->txq, skb); + hci_uart_tx_wakeup(hu); + + intel_wait_lpm_transaction(hu); + /* Even in case of failure, continue and test the suspended flag */ + + clear_bit(STATE_LPM_TRANSACTION, &intel->flags); + + if (test_bit(STATE_SUSPENDED, &intel->flags)) { + bt_dev_err(hu->hdev, "Device resume error"); + return -EINVAL; + } + + bt_dev_dbg(hu->hdev, "Resumed"); + + return 0; +} +#endif /* CONFIG_PM */ + +static int intel_lpm_host_wake(struct hci_uart *hu) +{ + static const u8 lpm_resume_ack[] = { LPM_OP_RESUME_ACK, 0x00 }; + struct intel_data *intel = hu->priv; + struct sk_buff *skb; + + hci_uart_set_flow_control(hu, false); + + clear_bit(STATE_SUSPENDED, &intel->flags); + + skb = bt_skb_alloc(sizeof(lpm_resume_ack), GFP_KERNEL); + if (!skb) { + bt_dev_err(hu->hdev, "Failed to alloc memory for LPM packet"); + return -ENOMEM; + } + + skb_put_data(skb, lpm_resume_ack, sizeof(lpm_resume_ack)); + hci_skb_pkt_type(skb) = HCI_LPM_PKT; + + /* LPM flow is a priority, enqueue packet at list head */ + skb_queue_head(&intel->txq, skb); + hci_uart_tx_wakeup(hu); + + bt_dev_dbg(hu->hdev, "Resumed by controller"); + + return 0; +} + +static irqreturn_t intel_irq(int irq, void *dev_id) +{ + struct intel_device *idev = dev_id; + + dev_info(&idev->pdev->dev, "hci_intel irq\n"); + + mutex_lock(&idev->hu_lock); + if (idev->hu) + intel_lpm_host_wake(idev->hu); + mutex_unlock(&idev->hu_lock); + + /* Host/Controller are now LPM resumed, trigger a new delayed suspend */ + pm_runtime_get(&idev->pdev->dev); + pm_runtime_mark_last_busy(&idev->pdev->dev); + pm_runtime_put_autosuspend(&idev->pdev->dev); + + return IRQ_HANDLED; +} + +static int intel_set_power(struct hci_uart *hu, bool powered) +{ + struct intel_device *idev; + int err = -ENODEV; + + if (!hu->tty->dev) + return err; + + mutex_lock(&intel_device_list_lock); + + list_for_each_entry(idev, &intel_device_list, list) { + /* tty device and pdev device should share the same parent + * which is the UART port. + */ + if (hu->tty->dev->parent != idev->pdev->dev.parent) + continue; + + if (!idev->reset) { + err = -ENOTSUPP; + break; + } + + BT_INFO("hu %p, Switching compatible pm device (%s) to %u", + hu, dev_name(&idev->pdev->dev), powered); + + gpiod_set_value(idev->reset, powered); + + /* Provide to idev a hu reference which is used to run LPM + * transactions (lpm suspend/resume) from PM callbacks. + * hu needs to be protected against concurrent removing during + * these PM ops. + */ + mutex_lock(&idev->hu_lock); + idev->hu = powered ? hu : NULL; + mutex_unlock(&idev->hu_lock); + + if (idev->irq < 0) + break; + + if (powered && device_can_wakeup(&idev->pdev->dev)) { + err = devm_request_threaded_irq(&idev->pdev->dev, + idev->irq, NULL, + intel_irq, + IRQF_ONESHOT, + "bt-host-wake", idev); + if (err) { + BT_ERR("hu %p, unable to allocate irq-%d", + hu, idev->irq); + break; + } + + device_wakeup_enable(&idev->pdev->dev); + + pm_runtime_set_active(&idev->pdev->dev); + pm_runtime_use_autosuspend(&idev->pdev->dev); + pm_runtime_set_autosuspend_delay(&idev->pdev->dev, + LPM_SUSPEND_DELAY_MS); + pm_runtime_enable(&idev->pdev->dev); + } else if (!powered && device_may_wakeup(&idev->pdev->dev)) { + devm_free_irq(&idev->pdev->dev, idev->irq, idev); + device_wakeup_disable(&idev->pdev->dev); + + pm_runtime_disable(&idev->pdev->dev); + } + } + + mutex_unlock(&intel_device_list_lock); + + return err; +} + +static void intel_busy_work(struct work_struct *work) +{ + struct intel_data *intel = container_of(work, struct intel_data, + busy_work); + struct intel_device *idev; + + if (!intel->hu->tty->dev) + return; + + /* Link is busy, delay the suspend */ + mutex_lock(&intel_device_list_lock); + list_for_each_entry(idev, &intel_device_list, list) { + if (intel->hu->tty->dev->parent == idev->pdev->dev.parent) { + pm_runtime_get(&idev->pdev->dev); + pm_runtime_mark_last_busy(&idev->pdev->dev); + pm_runtime_put_autosuspend(&idev->pdev->dev); + break; + } + } + mutex_unlock(&intel_device_list_lock); +} + +static int intel_open(struct hci_uart *hu) +{ + struct intel_data *intel; + + BT_DBG("hu %p", hu); + + if (!hci_uart_has_flow_control(hu)) + return -EOPNOTSUPP; + + intel = kzalloc(sizeof(*intel), GFP_KERNEL); + if (!intel) + return -ENOMEM; + + skb_queue_head_init(&intel->txq); + INIT_WORK(&intel->busy_work, intel_busy_work); + + intel->hu = hu; + + hu->priv = intel; + + if (!intel_set_power(hu, true)) + set_bit(STATE_BOOTING, &intel->flags); + + return 0; +} + +static int intel_close(struct hci_uart *hu) +{ + struct intel_data *intel = hu->priv; + + BT_DBG("hu %p", hu); + + cancel_work_sync(&intel->busy_work); + + intel_set_power(hu, false); + + skb_queue_purge(&intel->txq); + kfree_skb(intel->rx_skb); + kfree(intel); + + hu->priv = NULL; + return 0; +} + +static int intel_flush(struct hci_uart *hu) +{ + struct intel_data *intel = hu->priv; + + BT_DBG("hu %p", hu); + + skb_queue_purge(&intel->txq); + + return 0; +} + +static int inject_cmd_complete(struct hci_dev *hdev, __u16 opcode) +{ + struct sk_buff *skb; + struct hci_event_hdr *hdr; + struct hci_ev_cmd_complete *evt; + + skb = bt_skb_alloc(sizeof(*hdr) + sizeof(*evt) + 1, GFP_KERNEL); + if (!skb) + return -ENOMEM; + + hdr = skb_put(skb, sizeof(*hdr)); + hdr->evt = HCI_EV_CMD_COMPLETE; + hdr->plen = sizeof(*evt) + 1; + + evt = skb_put(skb, sizeof(*evt)); + evt->ncmd = 0x01; + evt->opcode = cpu_to_le16(opcode); + + skb_put_u8(skb, 0x00); + + hci_skb_pkt_type(skb) = HCI_EVENT_PKT; + + return hci_recv_frame(hdev, skb); +} + +static int intel_set_baudrate(struct hci_uart *hu, unsigned int speed) +{ + struct intel_data *intel = hu->priv; + struct hci_dev *hdev = hu->hdev; + u8 speed_cmd[] = { 0x06, 0xfc, 0x01, 0x00 }; + struct sk_buff *skb; + int err; + + /* This can be the first command sent to the chip, check + * that the controller is ready. + */ + err = intel_wait_booting(hu); + + clear_bit(STATE_BOOTING, &intel->flags); + + /* In case of timeout, try to continue anyway */ + if (err && err != -ETIMEDOUT) + return err; + + bt_dev_info(hdev, "Change controller speed to %d", speed); + + speed_cmd[3] = intel_convert_speed(speed); + if (speed_cmd[3] == 0xff) { + bt_dev_err(hdev, "Unsupported speed"); + return -EINVAL; + } + + /* Device will not accept speed change if Intel version has not been + * previously requested. + */ + skb = __hci_cmd_sync(hdev, 0xfc05, 0, NULL, HCI_CMD_TIMEOUT); + if (IS_ERR(skb)) { + bt_dev_err(hdev, "Reading Intel version information failed (%ld)", + PTR_ERR(skb)); + return PTR_ERR(skb); + } + kfree_skb(skb); + + skb = bt_skb_alloc(sizeof(speed_cmd), GFP_KERNEL); + if (!skb) { + bt_dev_err(hdev, "Failed to alloc memory for baudrate packet"); + return -ENOMEM; + } + + skb_put_data(skb, speed_cmd, sizeof(speed_cmd)); + hci_skb_pkt_type(skb) = HCI_COMMAND_PKT; + + hci_uart_set_flow_control(hu, true); + + skb_queue_tail(&intel->txq, skb); + hci_uart_tx_wakeup(hu); + + /* wait 100ms to change baudrate on controller side */ + msleep(100); + + hci_uart_set_baudrate(hu, speed); + hci_uart_set_flow_control(hu, false); + + return 0; +} + +static int intel_setup(struct hci_uart *hu) +{ + struct intel_data *intel = hu->priv; + struct hci_dev *hdev = hu->hdev; + struct sk_buff *skb; + struct intel_version ver; + struct intel_boot_params params; + struct intel_device *idev; + const struct firmware *fw; + char fwname[64]; + u32 boot_param; + ktime_t calltime, delta, rettime; + unsigned long long duration; + unsigned int init_speed, oper_speed; + int speed_change = 0; + int err; + + bt_dev_dbg(hdev, "start intel_setup"); + + hu->hdev->set_diag = btintel_set_diag; + hu->hdev->set_bdaddr = btintel_set_bdaddr; + + /* Set the default boot parameter to 0x0 and it is updated to + * SKU specific boot parameter after reading Intel_Write_Boot_Params + * command while downloading the firmware. + */ + boot_param = 0x00000000; + + calltime = ktime_get(); + + if (hu->init_speed) + init_speed = hu->init_speed; + else + init_speed = hu->proto->init_speed; + + if (hu->oper_speed) + oper_speed = hu->oper_speed; + else + oper_speed = hu->proto->oper_speed; + + if (oper_speed && init_speed && oper_speed != init_speed) + speed_change = 1; + + /* Check that the controller is ready */ + err = intel_wait_booting(hu); + + clear_bit(STATE_BOOTING, &intel->flags); + + /* In case of timeout, try to continue anyway */ + if (err && err != -ETIMEDOUT) + return err; + + set_bit(STATE_BOOTLOADER, &intel->flags); + + /* Read the Intel version information to determine if the device + * is in bootloader mode or if it already has operational firmware + * loaded. + */ + err = btintel_read_version(hdev, &ver); + if (err) + return err; + + /* The hardware platform number has a fixed value of 0x37 and + * for now only accept this single value. + */ + if (ver.hw_platform != 0x37) { + bt_dev_err(hdev, "Unsupported Intel hardware platform (%u)", + ver.hw_platform); + return -EINVAL; + } + + /* Check for supported iBT hardware variants of this firmware + * loading method. + * + * This check has been put in place to ensure correct forward + * compatibility options when newer hardware variants come along. + */ + switch (ver.hw_variant) { + case 0x0b: /* LnP */ + case 0x0c: /* WsP */ + case 0x12: /* ThP */ + break; + default: + bt_dev_err(hdev, "Unsupported Intel hardware variant (%u)", + ver.hw_variant); + return -EINVAL; + } + + btintel_version_info(hdev, &ver); + + /* The firmware variant determines if the device is in bootloader + * mode or is running operational firmware. The value 0x06 identifies + * the bootloader and the value 0x23 identifies the operational + * firmware. + * + * When the operational firmware is already present, then only + * the check for valid Bluetooth device address is needed. This + * determines if the device will be added as configured or + * unconfigured controller. + * + * It is not possible to use the Secure Boot Parameters in this + * case since that command is only available in bootloader mode. + */ + if (ver.fw_variant == 0x23) { + clear_bit(STATE_BOOTLOADER, &intel->flags); + btintel_check_bdaddr(hdev); + return 0; + } + + /* If the device is not in bootloader mode, then the only possible + * choice is to return an error and abort the device initialization. + */ + if (ver.fw_variant != 0x06) { + bt_dev_err(hdev, "Unsupported Intel firmware variant (%u)", + ver.fw_variant); + return -ENODEV; + } + + /* Read the secure boot parameters to identify the operating + * details of the bootloader. + */ + err = btintel_read_boot_params(hdev, ¶ms); + if (err) + return err; + + /* It is required that every single firmware fragment is acknowledged + * with a command complete event. If the boot parameters indicate + * that this bootloader does not send them, then abort the setup. + */ + if (params.limited_cce != 0x00) { + bt_dev_err(hdev, "Unsupported Intel firmware loading method (%u)", + params.limited_cce); + return -EINVAL; + } + + /* If the OTP has no valid Bluetooth device address, then there will + * also be no valid address for the operational firmware. + */ + if (!bacmp(¶ms.otp_bdaddr, BDADDR_ANY)) { + bt_dev_info(hdev, "No device address configured"); + set_bit(HCI_QUIRK_INVALID_BDADDR, &hdev->quirks); + } + + /* With this Intel bootloader only the hardware variant and device + * revision information are used to select the right firmware for SfP + * and WsP. + * + * The firmware filename is ibt-<hw_variant>-<dev_revid>.sfi. + * + * Currently the supported hardware variants are: + * 11 (0x0b) for iBT 3.0 (LnP/SfP) + * 12 (0x0c) for iBT 3.5 (WsP) + * + * For ThP/JfP and for future SKU's, the FW name varies based on HW + * variant, HW revision and FW revision, as these are dependent on CNVi + * and RF Combination. + * + * 18 (0x12) for iBT3.5 (ThP/JfP) + * + * The firmware file name for these will be + * ibt-<hw_variant>-<hw_revision>-<fw_revision>.sfi. + * + */ + switch (ver.hw_variant) { + case 0x0b: /* SfP */ + case 0x0c: /* WsP */ + snprintf(fwname, sizeof(fwname), "intel/ibt-%u-%u.sfi", + ver.hw_variant, le16_to_cpu(params.dev_revid)); + break; + case 0x12: /* ThP */ + snprintf(fwname, sizeof(fwname), "intel/ibt-%u-%u-%u.sfi", + ver.hw_variant, ver.hw_revision, ver.fw_revision); + break; + default: + bt_dev_err(hdev, "Unsupported Intel hardware variant (%u)", + ver.hw_variant); + return -EINVAL; + } + + err = request_firmware(&fw, fwname, &hdev->dev); + if (err < 0) { + bt_dev_err(hdev, "Failed to load Intel firmware file (%d)", + err); + return err; + } + + bt_dev_info(hdev, "Found device firmware: %s", fwname); + + /* Save the DDC file name for later */ + switch (ver.hw_variant) { + case 0x0b: /* SfP */ + case 0x0c: /* WsP */ + snprintf(fwname, sizeof(fwname), "intel/ibt-%u-%u.ddc", + ver.hw_variant, le16_to_cpu(params.dev_revid)); + break; + case 0x12: /* ThP */ + snprintf(fwname, sizeof(fwname), "intel/ibt-%u-%u-%u.ddc", + ver.hw_variant, ver.hw_revision, ver.fw_revision); + break; + default: + bt_dev_err(hdev, "Unsupported Intel hardware variant (%u)", + ver.hw_variant); + return -EINVAL; + } + + if (fw->size < 644) { + bt_dev_err(hdev, "Invalid size of firmware file (%zu)", + fw->size); + err = -EBADF; + goto done; + } + + set_bit(STATE_DOWNLOADING, &intel->flags); + + /* Start firmware downloading and get boot parameter */ + err = btintel_download_firmware(hdev, &ver, fw, &boot_param); + if (err < 0) + goto done; + + set_bit(STATE_FIRMWARE_LOADED, &intel->flags); + + bt_dev_info(hdev, "Waiting for firmware download to complete"); + + /* Before switching the device into operational mode and with that + * booting the loaded firmware, wait for the bootloader notification + * that all fragments have been successfully received. + * + * When the event processing receives the notification, then the + * STATE_DOWNLOADING flag will be cleared. + * + * The firmware loading should not take longer than 5 seconds + * and thus just timeout if that happens and fail the setup + * of this device. + */ + err = wait_on_bit_timeout(&intel->flags, STATE_DOWNLOADING, + TASK_INTERRUPTIBLE, + msecs_to_jiffies(5000)); + if (err == -EINTR) { + bt_dev_err(hdev, "Firmware loading interrupted"); + err = -EINTR; + goto done; + } + + if (err) { + bt_dev_err(hdev, "Firmware loading timeout"); + err = -ETIMEDOUT; + goto done; + } + + if (test_bit(STATE_FIRMWARE_FAILED, &intel->flags)) { + bt_dev_err(hdev, "Firmware loading failed"); + err = -ENOEXEC; + goto done; + } + + rettime = ktime_get(); + delta = ktime_sub(rettime, calltime); + duration = (unsigned long long) ktime_to_ns(delta) >> 10; + + bt_dev_info(hdev, "Firmware loaded in %llu usecs", duration); + +done: + release_firmware(fw); + + /* Check if there was an error and if is not -EALREADY which means the + * firmware has already been loaded. + */ + if (err < 0 && err != -EALREADY) + return err; + + /* We need to restore the default speed before Intel reset */ + if (speed_change) { + err = intel_set_baudrate(hu, init_speed); + if (err) + return err; + } + + calltime = ktime_get(); + + set_bit(STATE_BOOTING, &intel->flags); + + err = btintel_send_intel_reset(hdev, boot_param); + if (err) + return err; + + /* The bootloader will not indicate when the device is ready. This + * is done by the operational firmware sending bootup notification. + * + * Booting into operational firmware should not take longer than + * 1 second. However if that happens, then just fail the setup + * since something went wrong. + */ + bt_dev_info(hdev, "Waiting for device to boot"); + + err = intel_wait_booting(hu); + if (err) + return err; + + clear_bit(STATE_BOOTING, &intel->flags); + + rettime = ktime_get(); + delta = ktime_sub(rettime, calltime); + duration = (unsigned long long) ktime_to_ns(delta) >> 10; + + bt_dev_info(hdev, "Device booted in %llu usecs", duration); + + /* Enable LPM if matching pdev with wakeup enabled, set TX active + * until further LPM TX notification. + */ + mutex_lock(&intel_device_list_lock); + list_for_each_entry(idev, &intel_device_list, list) { + if (!hu->tty->dev) + break; + if (hu->tty->dev->parent == idev->pdev->dev.parent) { + if (device_may_wakeup(&idev->pdev->dev)) { + set_bit(STATE_LPM_ENABLED, &intel->flags); + set_bit(STATE_TX_ACTIVE, &intel->flags); + } + break; + } + } + mutex_unlock(&intel_device_list_lock); + + /* Ignore errors, device can work without DDC parameters */ + btintel_load_ddc_config(hdev, fwname); + + skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL, HCI_CMD_TIMEOUT); + if (IS_ERR(skb)) + return PTR_ERR(skb); + kfree_skb(skb); + + if (speed_change) { + err = intel_set_baudrate(hu, oper_speed); + if (err) + return err; + } + + bt_dev_info(hdev, "Setup complete"); + + clear_bit(STATE_BOOTLOADER, &intel->flags); + + return 0; +} + +static int intel_recv_event(struct hci_dev *hdev, struct sk_buff *skb) +{ + struct hci_uart *hu = hci_get_drvdata(hdev); + struct intel_data *intel = hu->priv; + struct hci_event_hdr *hdr; + + if (!test_bit(STATE_BOOTLOADER, &intel->flags) && + !test_bit(STATE_BOOTING, &intel->flags)) + goto recv; + + hdr = (void *)skb->data; + + /* When the firmware loading completes the device sends + * out a vendor specific event indicating the result of + * the firmware loading. + */ + if (skb->len == 7 && hdr->evt == 0xff && hdr->plen == 0x05 && + skb->data[2] == 0x06) { + if (skb->data[3] != 0x00) + set_bit(STATE_FIRMWARE_FAILED, &intel->flags); + + if (test_and_clear_bit(STATE_DOWNLOADING, &intel->flags) && + test_bit(STATE_FIRMWARE_LOADED, &intel->flags)) + wake_up_bit(&intel->flags, STATE_DOWNLOADING); + + /* When switching to the operational firmware the device + * sends a vendor specific event indicating that the bootup + * completed. + */ + } else if (skb->len == 9 && hdr->evt == 0xff && hdr->plen == 0x07 && + skb->data[2] == 0x02) { + if (test_and_clear_bit(STATE_BOOTING, &intel->flags)) + wake_up_bit(&intel->flags, STATE_BOOTING); + } +recv: + return hci_recv_frame(hdev, skb); +} + +static void intel_recv_lpm_notify(struct hci_dev *hdev, int value) +{ + struct hci_uart *hu = hci_get_drvdata(hdev); + struct intel_data *intel = hu->priv; + + bt_dev_dbg(hdev, "TX idle notification (%d)", value); + + if (value) { + set_bit(STATE_TX_ACTIVE, &intel->flags); + schedule_work(&intel->busy_work); + } else { + clear_bit(STATE_TX_ACTIVE, &intel->flags); + } +} + +static int intel_recv_lpm(struct hci_dev *hdev, struct sk_buff *skb) +{ + struct hci_lpm_pkt *lpm = (void *)skb->data; + struct hci_uart *hu = hci_get_drvdata(hdev); + struct intel_data *intel = hu->priv; + + switch (lpm->opcode) { + case LPM_OP_TX_NOTIFY: + if (lpm->dlen < 1) { + bt_dev_err(hu->hdev, "Invalid LPM notification packet"); + break; + } + intel_recv_lpm_notify(hdev, lpm->data[0]); + break; + case LPM_OP_SUSPEND_ACK: + set_bit(STATE_SUSPENDED, &intel->flags); + if (test_and_clear_bit(STATE_LPM_TRANSACTION, &intel->flags)) + wake_up_bit(&intel->flags, STATE_LPM_TRANSACTION); + break; + case LPM_OP_RESUME_ACK: + clear_bit(STATE_SUSPENDED, &intel->flags); + if (test_and_clear_bit(STATE_LPM_TRANSACTION, &intel->flags)) + wake_up_bit(&intel->flags, STATE_LPM_TRANSACTION); + break; + default: + bt_dev_err(hdev, "Unknown LPM opcode (%02x)", lpm->opcode); + break; + } + + kfree_skb(skb); + + return 0; +} + +#define INTEL_RECV_LPM \ + .type = HCI_LPM_PKT, \ + .hlen = HCI_LPM_HDR_SIZE, \ + .loff = 1, \ + .lsize = 1, \ + .maxlen = HCI_LPM_MAX_SIZE + +static const struct h4_recv_pkt intel_recv_pkts[] = { + { H4_RECV_ACL, .recv = hci_recv_frame }, + { H4_RECV_SCO, .recv = hci_recv_frame }, + { H4_RECV_EVENT, .recv = intel_recv_event }, + { INTEL_RECV_LPM, .recv = intel_recv_lpm }, +}; + +static int intel_recv(struct hci_uart *hu, const void *data, int count) +{ + struct intel_data *intel = hu->priv; + + if (!test_bit(HCI_UART_REGISTERED, &hu->flags)) + return -EUNATCH; + + intel->rx_skb = h4_recv_buf(hu->hdev, intel->rx_skb, data, count, + intel_recv_pkts, + ARRAY_SIZE(intel_recv_pkts)); + if (IS_ERR(intel->rx_skb)) { + int err = PTR_ERR(intel->rx_skb); + bt_dev_err(hu->hdev, "Frame reassembly failed (%d)", err); + intel->rx_skb = NULL; + return err; + } + + return count; +} + +static int intel_enqueue(struct hci_uart *hu, struct sk_buff *skb) +{ + struct intel_data *intel = hu->priv; + struct intel_device *idev; + + BT_DBG("hu %p skb %p", hu, skb); + + if (!hu->tty->dev) + goto out_enqueue; + + /* Be sure our controller is resumed and potential LPM transaction + * completed before enqueuing any packet. + */ + mutex_lock(&intel_device_list_lock); + list_for_each_entry(idev, &intel_device_list, list) { + if (hu->tty->dev->parent == idev->pdev->dev.parent) { + pm_runtime_get_sync(&idev->pdev->dev); + pm_runtime_mark_last_busy(&idev->pdev->dev); + pm_runtime_put_autosuspend(&idev->pdev->dev); + break; + } + } + mutex_unlock(&intel_device_list_lock); +out_enqueue: + skb_queue_tail(&intel->txq, skb); + + return 0; +} + +static struct sk_buff *intel_dequeue(struct hci_uart *hu) +{ + struct intel_data *intel = hu->priv; + struct sk_buff *skb; + + skb = skb_dequeue(&intel->txq); + if (!skb) + return skb; + + if (test_bit(STATE_BOOTLOADER, &intel->flags) && + (hci_skb_pkt_type(skb) == HCI_COMMAND_PKT)) { + struct hci_command_hdr *cmd = (void *)skb->data; + __u16 opcode = le16_to_cpu(cmd->opcode); + + /* When the 0xfc01 command is issued to boot into + * the operational firmware, it will actually not + * send a command complete event. To keep the flow + * control working inject that event here. + */ + if (opcode == 0xfc01) + inject_cmd_complete(hu->hdev, opcode); + } + + /* Prepend skb with frame type */ + memcpy(skb_push(skb, 1), &hci_skb_pkt_type(skb), 1); + + return skb; +} + +static const struct hci_uart_proto intel_proto = { + .id = HCI_UART_INTEL, + .name = "Intel", + .manufacturer = 2, + .init_speed = 115200, + .oper_speed = 3000000, + .open = intel_open, + .close = intel_close, + .flush = intel_flush, + .setup = intel_setup, + .set_baudrate = intel_set_baudrate, + .recv = intel_recv, + .enqueue = intel_enqueue, + .dequeue = intel_dequeue, +}; + +#ifdef CONFIG_ACPI +static const struct acpi_device_id intel_acpi_match[] = { + { "INT33E1", 0 }, + { "INT33E3", 0 }, + { } +}; +MODULE_DEVICE_TABLE(acpi, intel_acpi_match); +#endif + +#ifdef CONFIG_PM +static int intel_suspend_device(struct device *dev) +{ + struct intel_device *idev = dev_get_drvdata(dev); + + mutex_lock(&idev->hu_lock); + if (idev->hu) + intel_lpm_suspend(idev->hu); + mutex_unlock(&idev->hu_lock); + + return 0; +} + +static int intel_resume_device(struct device *dev) +{ + struct intel_device *idev = dev_get_drvdata(dev); + + mutex_lock(&idev->hu_lock); + if (idev->hu) + intel_lpm_resume(idev->hu); + mutex_unlock(&idev->hu_lock); + + return 0; +} +#endif + +#ifdef CONFIG_PM_SLEEP +static int intel_suspend(struct device *dev) +{ + struct intel_device *idev = dev_get_drvdata(dev); + + if (device_may_wakeup(dev)) + enable_irq_wake(idev->irq); + + return intel_suspend_device(dev); +} + +static int intel_resume(struct device *dev) +{ + struct intel_device *idev = dev_get_drvdata(dev); + + if (device_may_wakeup(dev)) + disable_irq_wake(idev->irq); + + return intel_resume_device(dev); +} +#endif + +static const struct dev_pm_ops intel_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(intel_suspend, intel_resume) + SET_RUNTIME_PM_OPS(intel_suspend_device, intel_resume_device, NULL) +}; + +static const struct acpi_gpio_params reset_gpios = { 0, 0, false }; +static const struct acpi_gpio_params host_wake_gpios = { 1, 0, false }; + +static const struct acpi_gpio_mapping acpi_hci_intel_gpios[] = { + { "reset-gpios", &reset_gpios, 1, ACPI_GPIO_QUIRK_ONLY_GPIOIO }, + { "host-wake-gpios", &host_wake_gpios, 1, ACPI_GPIO_QUIRK_ONLY_GPIOIO }, + { } +}; + +static int intel_probe(struct platform_device *pdev) +{ + struct intel_device *idev; + int ret; + + idev = devm_kzalloc(&pdev->dev, sizeof(*idev), GFP_KERNEL); + if (!idev) + return -ENOMEM; + + mutex_init(&idev->hu_lock); + + idev->pdev = pdev; + + ret = devm_acpi_dev_add_driver_gpios(&pdev->dev, acpi_hci_intel_gpios); + if (ret) + dev_dbg(&pdev->dev, "Unable to add GPIO mapping table\n"); + + idev->reset = devm_gpiod_get(&pdev->dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(idev->reset)) { + dev_err(&pdev->dev, "Unable to retrieve gpio\n"); + return PTR_ERR(idev->reset); + } + + idev->irq = platform_get_irq(pdev, 0); + if (idev->irq < 0) { + struct gpio_desc *host_wake; + + dev_err(&pdev->dev, "No IRQ, falling back to gpio-irq\n"); + + host_wake = devm_gpiod_get(&pdev->dev, "host-wake", GPIOD_IN); + if (IS_ERR(host_wake)) { + dev_err(&pdev->dev, "Unable to retrieve IRQ\n"); + goto no_irq; + } + + idev->irq = gpiod_to_irq(host_wake); + if (idev->irq < 0) { + dev_err(&pdev->dev, "No corresponding irq for gpio\n"); + goto no_irq; + } + } + + /* Only enable wake-up/irq when controller is powered */ + device_set_wakeup_capable(&pdev->dev, true); + device_wakeup_disable(&pdev->dev); + +no_irq: + platform_set_drvdata(pdev, idev); + + /* Place this instance on the device list */ + mutex_lock(&intel_device_list_lock); + list_add_tail(&idev->list, &intel_device_list); + mutex_unlock(&intel_device_list_lock); + + dev_info(&pdev->dev, "registered, gpio(%d)/irq(%d).\n", + desc_to_gpio(idev->reset), idev->irq); + + return 0; +} + +static int intel_remove(struct platform_device *pdev) +{ + struct intel_device *idev = platform_get_drvdata(pdev); + + device_wakeup_disable(&pdev->dev); + + mutex_lock(&intel_device_list_lock); + list_del(&idev->list); + mutex_unlock(&intel_device_list_lock); + + dev_info(&pdev->dev, "unregistered.\n"); + + return 0; +} + +static struct platform_driver intel_driver = { + .probe = intel_probe, + .remove = intel_remove, + .driver = { + .name = "hci_intel", + .acpi_match_table = ACPI_PTR(intel_acpi_match), + .pm = &intel_pm_ops, + }, +}; + +int __init intel_init(void) +{ + int err; + + err = platform_driver_register(&intel_driver); + if (err) + return err; + + return hci_uart_register_proto(&intel_proto); +} + +int __exit intel_deinit(void) +{ + platform_driver_unregister(&intel_driver); + + return hci_uart_unregister_proto(&intel_proto); +} |