diff options
Diffstat (limited to 'drivers/gpu/drm/bridge/ti-sn65dsi86.c')
| -rw-r--r-- | drivers/gpu/drm/bridge/ti-sn65dsi86.c | 2043 |
1 files changed, 2043 insertions, 0 deletions
diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi86.c b/drivers/gpu/drm/bridge/ti-sn65dsi86.c new file mode 100644 index 000000000..3309c01fa --- /dev/null +++ b/drivers/gpu/drm/bridge/ti-sn65dsi86.c @@ -0,0 +1,2043 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2018, The Linux Foundation. All rights reserved. + * datasheet: https://www.ti.com/lit/ds/symlink/sn65dsi86.pdf + */ + +#include <linux/atomic.h> +#include <linux/auxiliary_bus.h> +#include <linux/bitfield.h> +#include <linux/bits.h> +#include <linux/clk.h> +#include <linux/debugfs.h> +#include <linux/gpio/consumer.h> +#include <linux/gpio/driver.h> +#include <linux/i2c.h> +#include <linux/iopoll.h> +#include <linux/module.h> +#include <linux/of_graph.h> +#include <linux/pm_runtime.h> +#include <linux/pwm.h> +#include <linux/regmap.h> +#include <linux/regulator/consumer.h> + +#include <asm/unaligned.h> + +#include <drm/display/drm_dp_aux_bus.h> +#include <drm/display/drm_dp_helper.h> +#include <drm/drm_atomic.h> +#include <drm/drm_atomic_helper.h> +#include <drm/drm_bridge.h> +#include <drm/drm_bridge_connector.h> +#include <drm/drm_edid.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_of.h> +#include <drm/drm_panel.h> +#include <drm/drm_print.h> +#include <drm/drm_probe_helper.h> + +#define SN_DEVICE_REV_REG 0x08 +#define SN_DPPLL_SRC_REG 0x0A +#define DPPLL_CLK_SRC_DSICLK BIT(0) +#define REFCLK_FREQ_MASK GENMASK(3, 1) +#define REFCLK_FREQ(x) ((x) << 1) +#define DPPLL_SRC_DP_PLL_LOCK BIT(7) +#define SN_PLL_ENABLE_REG 0x0D +#define SN_DSI_LANES_REG 0x10 +#define CHA_DSI_LANES_MASK GENMASK(4, 3) +#define CHA_DSI_LANES(x) ((x) << 3) +#define SN_DSIA_CLK_FREQ_REG 0x12 +#define SN_CHA_ACTIVE_LINE_LENGTH_LOW_REG 0x20 +#define SN_CHA_VERTICAL_DISPLAY_SIZE_LOW_REG 0x24 +#define SN_CHA_HSYNC_PULSE_WIDTH_LOW_REG 0x2C +#define SN_CHA_HSYNC_PULSE_WIDTH_HIGH_REG 0x2D +#define CHA_HSYNC_POLARITY BIT(7) +#define SN_CHA_VSYNC_PULSE_WIDTH_LOW_REG 0x30 +#define SN_CHA_VSYNC_PULSE_WIDTH_HIGH_REG 0x31 +#define CHA_VSYNC_POLARITY BIT(7) +#define SN_CHA_HORIZONTAL_BACK_PORCH_REG 0x34 +#define SN_CHA_VERTICAL_BACK_PORCH_REG 0x36 +#define SN_CHA_HORIZONTAL_FRONT_PORCH_REG 0x38 +#define SN_CHA_VERTICAL_FRONT_PORCH_REG 0x3A +#define SN_LN_ASSIGN_REG 0x59 +#define LN_ASSIGN_WIDTH 2 +#define SN_ENH_FRAME_REG 0x5A +#define VSTREAM_ENABLE BIT(3) +#define LN_POLRS_OFFSET 4 +#define LN_POLRS_MASK 0xf0 +#define SN_DATA_FORMAT_REG 0x5B +#define BPP_18_RGB BIT(0) +#define SN_HPD_DISABLE_REG 0x5C +#define HPD_DISABLE BIT(0) +#define HPD_DEBOUNCED_STATE BIT(4) +#define SN_GPIO_IO_REG 0x5E +#define SN_GPIO_INPUT_SHIFT 4 +#define SN_GPIO_OUTPUT_SHIFT 0 +#define SN_GPIO_CTRL_REG 0x5F +#define SN_GPIO_MUX_INPUT 0 +#define SN_GPIO_MUX_OUTPUT 1 +#define SN_GPIO_MUX_SPECIAL 2 +#define SN_GPIO_MUX_MASK 0x3 +#define SN_AUX_WDATA_REG(x) (0x64 + (x)) +#define SN_AUX_ADDR_19_16_REG 0x74 +#define SN_AUX_ADDR_15_8_REG 0x75 +#define SN_AUX_ADDR_7_0_REG 0x76 +#define SN_AUX_ADDR_MASK GENMASK(19, 0) +#define SN_AUX_LENGTH_REG 0x77 +#define SN_AUX_CMD_REG 0x78 +#define AUX_CMD_SEND BIT(0) +#define AUX_CMD_REQ(x) ((x) << 4) +#define SN_AUX_RDATA_REG(x) (0x79 + (x)) +#define SN_SSC_CONFIG_REG 0x93 +#define DP_NUM_LANES_MASK GENMASK(5, 4) +#define DP_NUM_LANES(x) ((x) << 4) +#define SN_DATARATE_CONFIG_REG 0x94 +#define DP_DATARATE_MASK GENMASK(7, 5) +#define DP_DATARATE(x) ((x) << 5) +#define SN_TRAINING_SETTING_REG 0x95 +#define SCRAMBLE_DISABLE BIT(4) +#define SN_ML_TX_MODE_REG 0x96 +#define ML_TX_MAIN_LINK_OFF 0 +#define ML_TX_NORMAL_MODE BIT(0) +#define SN_PWM_PRE_DIV_REG 0xA0 +#define SN_BACKLIGHT_SCALE_REG 0xA1 +#define BACKLIGHT_SCALE_MAX 0xFFFF +#define SN_BACKLIGHT_REG 0xA3 +#define SN_PWM_EN_INV_REG 0xA5 +#define SN_PWM_INV_MASK BIT(0) +#define SN_PWM_EN_MASK BIT(1) +#define SN_AUX_CMD_STATUS_REG 0xF4 +#define AUX_IRQ_STATUS_AUX_RPLY_TOUT BIT(3) +#define AUX_IRQ_STATUS_AUX_SHORT BIT(5) +#define AUX_IRQ_STATUS_NAT_I2C_FAIL BIT(6) + +#define MIN_DSI_CLK_FREQ_MHZ 40 + +/* fudge factor required to account for 8b/10b encoding */ +#define DP_CLK_FUDGE_NUM 10 +#define DP_CLK_FUDGE_DEN 8 + +/* Matches DP_AUX_MAX_PAYLOAD_BYTES (for now) */ +#define SN_AUX_MAX_PAYLOAD_BYTES 16 + +#define SN_REGULATOR_SUPPLY_NUM 4 + +#define SN_MAX_DP_LANES 4 +#define SN_NUM_GPIOS 4 +#define SN_GPIO_PHYSICAL_OFFSET 1 + +#define SN_LINK_TRAINING_TRIES 10 + +#define SN_PWM_GPIO_IDX 3 /* 4th GPIO */ + +/** + * struct ti_sn65dsi86 - Platform data for ti-sn65dsi86 driver. + * @bridge_aux: AUX-bus sub device for MIPI-to-eDP bridge functionality. + * @gpio_aux: AUX-bus sub device for GPIO controller functionality. + * @aux_aux: AUX-bus sub device for eDP AUX channel functionality. + * @pwm_aux: AUX-bus sub device for PWM controller functionality. + * + * @dev: Pointer to the top level (i2c) device. + * @regmap: Regmap for accessing i2c. + * @aux: Our aux channel. + * @bridge: Our bridge. + * @connector: Our connector. + * @host_node: Remote DSI node. + * @dsi: Our MIPI DSI source. + * @refclk: Our reference clock. + * @next_bridge: The bridge on the eDP side. + * @enable_gpio: The GPIO we toggle to enable the bridge. + * @supplies: Data for bulk enabling/disabling our regulators. + * @dp_lanes: Count of dp_lanes we're using. + * @ln_assign: Value to program to the LN_ASSIGN register. + * @ln_polrs: Value for the 4-bit LN_POLRS field of SN_ENH_FRAME_REG. + * @comms_enabled: If true then communication over the aux channel is enabled. + * @comms_mutex: Protects modification of comms_enabled. + * + * @gchip: If we expose our GPIOs, this is used. + * @gchip_output: A cache of whether we've set GPIOs to output. This + * serves double-duty of keeping track of the direction and + * also keeping track of whether we've incremented the + * pm_runtime reference count for this pin, which we do + * whenever a pin is configured as an output. This is a + * bitmap so we can do atomic ops on it without an extra + * lock so concurrent users of our 4 GPIOs don't stomp on + * each other's read-modify-write. + * + * @pchip: pwm_chip if the PWM is exposed. + * @pwm_enabled: Used to track if the PWM signal is currently enabled. + * @pwm_pin_busy: Track if GPIO4 is currently requested for GPIO or PWM. + * @pwm_refclk_freq: Cache for the reference clock input to the PWM. + */ +struct ti_sn65dsi86 { + struct auxiliary_device *bridge_aux; + struct auxiliary_device *gpio_aux; + struct auxiliary_device *aux_aux; + struct auxiliary_device *pwm_aux; + + struct device *dev; + struct regmap *regmap; + struct drm_dp_aux aux; + struct drm_bridge bridge; + struct drm_connector *connector; + struct device_node *host_node; + struct mipi_dsi_device *dsi; + struct clk *refclk; + struct drm_bridge *next_bridge; + struct gpio_desc *enable_gpio; + struct regulator_bulk_data supplies[SN_REGULATOR_SUPPLY_NUM]; + int dp_lanes; + u8 ln_assign; + u8 ln_polrs; + bool comms_enabled; + struct mutex comms_mutex; + +#if defined(CONFIG_OF_GPIO) + struct gpio_chip gchip; + DECLARE_BITMAP(gchip_output, SN_NUM_GPIOS); +#endif +#if defined(CONFIG_PWM) + struct pwm_chip pchip; + bool pwm_enabled; + atomic_t pwm_pin_busy; +#endif + unsigned int pwm_refclk_freq; +}; + +static const struct regmap_range ti_sn65dsi86_volatile_ranges[] = { + { .range_min = 0, .range_max = 0xFF }, +}; + +static const struct regmap_access_table ti_sn_bridge_volatile_table = { + .yes_ranges = ti_sn65dsi86_volatile_ranges, + .n_yes_ranges = ARRAY_SIZE(ti_sn65dsi86_volatile_ranges), +}; + +static const struct regmap_config ti_sn65dsi86_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .volatile_table = &ti_sn_bridge_volatile_table, + .cache_type = REGCACHE_NONE, + .max_register = 0xFF, +}; + +static int __maybe_unused ti_sn65dsi86_read_u16(struct ti_sn65dsi86 *pdata, + unsigned int reg, u16 *val) +{ + u8 buf[2]; + int ret; + + ret = regmap_bulk_read(pdata->regmap, reg, buf, ARRAY_SIZE(buf)); + if (ret) + return ret; + + *val = buf[0] | (buf[1] << 8); + + return 0; +} + +static void ti_sn65dsi86_write_u16(struct ti_sn65dsi86 *pdata, + unsigned int reg, u16 val) +{ + u8 buf[2] = { val & 0xff, val >> 8 }; + + regmap_bulk_write(pdata->regmap, reg, buf, ARRAY_SIZE(buf)); +} + +static u32 ti_sn_bridge_get_dsi_freq(struct ti_sn65dsi86 *pdata) +{ + u32 bit_rate_khz, clk_freq_khz; + struct drm_display_mode *mode = + &pdata->bridge.encoder->crtc->state->adjusted_mode; + + bit_rate_khz = mode->clock * + mipi_dsi_pixel_format_to_bpp(pdata->dsi->format); + clk_freq_khz = bit_rate_khz / (pdata->dsi->lanes * 2); + + return clk_freq_khz; +} + +/* clk frequencies supported by bridge in Hz in case derived from REFCLK pin */ +static const u32 ti_sn_bridge_refclk_lut[] = { + 12000000, + 19200000, + 26000000, + 27000000, + 38400000, +}; + +/* clk frequencies supported by bridge in Hz in case derived from DACP/N pin */ +static const u32 ti_sn_bridge_dsiclk_lut[] = { + 468000000, + 384000000, + 416000000, + 486000000, + 460800000, +}; + +static void ti_sn_bridge_set_refclk_freq(struct ti_sn65dsi86 *pdata) +{ + int i; + u32 refclk_rate; + const u32 *refclk_lut; + size_t refclk_lut_size; + + if (pdata->refclk) { + refclk_rate = clk_get_rate(pdata->refclk); + refclk_lut = ti_sn_bridge_refclk_lut; + refclk_lut_size = ARRAY_SIZE(ti_sn_bridge_refclk_lut); + clk_prepare_enable(pdata->refclk); + } else { + refclk_rate = ti_sn_bridge_get_dsi_freq(pdata) * 1000; + refclk_lut = ti_sn_bridge_dsiclk_lut; + refclk_lut_size = ARRAY_SIZE(ti_sn_bridge_dsiclk_lut); + } + + /* for i equals to refclk_lut_size means default frequency */ + for (i = 0; i < refclk_lut_size; i++) + if (refclk_lut[i] == refclk_rate) + break; + + /* avoid buffer overflow and "1" is the default rate in the datasheet. */ + if (i >= refclk_lut_size) + i = 1; + + regmap_update_bits(pdata->regmap, SN_DPPLL_SRC_REG, REFCLK_FREQ_MASK, + REFCLK_FREQ(i)); + + /* + * The PWM refclk is based on the value written to SN_DPPLL_SRC_REG, + * regardless of its actual sourcing. + */ + pdata->pwm_refclk_freq = ti_sn_bridge_refclk_lut[i]; +} + +static void ti_sn65dsi86_enable_comms(struct ti_sn65dsi86 *pdata) +{ + mutex_lock(&pdata->comms_mutex); + + /* configure bridge ref_clk */ + ti_sn_bridge_set_refclk_freq(pdata); + + /* + * HPD on this bridge chip is a bit useless. This is an eDP bridge + * so the HPD is an internal signal that's only there to signal that + * the panel is done powering up. ...but the bridge chip debounces + * this signal by between 100 ms and 400 ms (depending on process, + * voltage, and temperate--I measured it at about 200 ms). One + * particular panel asserted HPD 84 ms after it was powered on meaning + * that we saw HPD 284 ms after power on. ...but the same panel said + * that instead of looking at HPD you could just hardcode a delay of + * 200 ms. We'll assume that the panel driver will have the hardcoded + * delay in its prepare and always disable HPD. + * + * If HPD somehow makes sense on some future panel we'll have to + * change this to be conditional on someone specifying that HPD should + * be used. + */ + regmap_update_bits(pdata->regmap, SN_HPD_DISABLE_REG, HPD_DISABLE, + HPD_DISABLE); + + pdata->comms_enabled = true; + + mutex_unlock(&pdata->comms_mutex); +} + +static void ti_sn65dsi86_disable_comms(struct ti_sn65dsi86 *pdata) +{ + mutex_lock(&pdata->comms_mutex); + + pdata->comms_enabled = false; + clk_disable_unprepare(pdata->refclk); + + mutex_unlock(&pdata->comms_mutex); +} + +static int __maybe_unused ti_sn65dsi86_resume(struct device *dev) +{ + struct ti_sn65dsi86 *pdata = dev_get_drvdata(dev); + int ret; + + ret = regulator_bulk_enable(SN_REGULATOR_SUPPLY_NUM, pdata->supplies); + if (ret) { + DRM_ERROR("failed to enable supplies %d\n", ret); + return ret; + } + + /* td2: min 100 us after regulators before enabling the GPIO */ + usleep_range(100, 110); + + gpiod_set_value_cansleep(pdata->enable_gpio, 1); + + /* + * If we have a reference clock we can enable communication w/ the + * panel (including the aux channel) w/out any need for an input clock + * so we can do it in resume which lets us read the EDID before + * pre_enable(). Without a reference clock we need the MIPI reference + * clock so reading early doesn't work. + */ + if (pdata->refclk) + ti_sn65dsi86_enable_comms(pdata); + + return ret; +} + +static int __maybe_unused ti_sn65dsi86_suspend(struct device *dev) +{ + struct ti_sn65dsi86 *pdata = dev_get_drvdata(dev); + int ret; + + if (pdata->refclk) + ti_sn65dsi86_disable_comms(pdata); + + gpiod_set_value_cansleep(pdata->enable_gpio, 0); + + ret = regulator_bulk_disable(SN_REGULATOR_SUPPLY_NUM, pdata->supplies); + if (ret) + DRM_ERROR("failed to disable supplies %d\n", ret); + + return ret; +} + +static const struct dev_pm_ops ti_sn65dsi86_pm_ops = { + SET_RUNTIME_PM_OPS(ti_sn65dsi86_suspend, ti_sn65dsi86_resume, NULL) + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, + pm_runtime_force_resume) +}; + +static int status_show(struct seq_file *s, void *data) +{ + struct ti_sn65dsi86 *pdata = s->private; + unsigned int reg, val; + + seq_puts(s, "STATUS REGISTERS:\n"); + + pm_runtime_get_sync(pdata->dev); + + /* IRQ Status Registers, see Table 31 in datasheet */ + for (reg = 0xf0; reg <= 0xf8; reg++) { + regmap_read(pdata->regmap, reg, &val); + seq_printf(s, "[0x%02x] = 0x%08x\n", reg, val); + } + + pm_runtime_put_autosuspend(pdata->dev); + + return 0; +} + +DEFINE_SHOW_ATTRIBUTE(status); + +static void ti_sn65dsi86_debugfs_remove(void *data) +{ + debugfs_remove_recursive(data); +} + +static void ti_sn65dsi86_debugfs_init(struct ti_sn65dsi86 *pdata) +{ + struct device *dev = pdata->dev; + struct dentry *debugfs; + int ret; + + debugfs = debugfs_create_dir(dev_name(dev), NULL); + + /* + * We might get an error back if debugfs wasn't enabled in the kernel + * so let's just silently return upon failure. + */ + if (IS_ERR_OR_NULL(debugfs)) + return; + + ret = devm_add_action_or_reset(dev, ti_sn65dsi86_debugfs_remove, debugfs); + if (ret) + return; + + debugfs_create_file("status", 0600, debugfs, pdata, &status_fops); +} + +/* ----------------------------------------------------------------------------- + * Auxiliary Devices (*not* AUX) + */ + +static void ti_sn65dsi86_uninit_aux(void *data) +{ + auxiliary_device_uninit(data); +} + +static void ti_sn65dsi86_delete_aux(void *data) +{ + auxiliary_device_delete(data); +} + +static void ti_sn65dsi86_aux_device_release(struct device *dev) +{ + struct auxiliary_device *aux = container_of(dev, struct auxiliary_device, dev); + + kfree(aux); +} + +static int ti_sn65dsi86_add_aux_device(struct ti_sn65dsi86 *pdata, + struct auxiliary_device **aux_out, + const char *name) +{ + struct device *dev = pdata->dev; + struct auxiliary_device *aux; + int ret; + + aux = kzalloc(sizeof(*aux), GFP_KERNEL); + if (!aux) + return -ENOMEM; + + aux->name = name; + aux->dev.parent = dev; + aux->dev.release = ti_sn65dsi86_aux_device_release; + device_set_of_node_from_dev(&aux->dev, dev); + ret = auxiliary_device_init(aux); + if (ret) { + kfree(aux); + return ret; + } + ret = devm_add_action_or_reset(dev, ti_sn65dsi86_uninit_aux, aux); + if (ret) + return ret; + + ret = auxiliary_device_add(aux); + if (ret) + return ret; + ret = devm_add_action_or_reset(dev, ti_sn65dsi86_delete_aux, aux); + if (!ret) + *aux_out = aux; + + return ret; +} + +/* ----------------------------------------------------------------------------- + * AUX Adapter + */ + +static struct ti_sn65dsi86 *aux_to_ti_sn65dsi86(struct drm_dp_aux *aux) +{ + return container_of(aux, struct ti_sn65dsi86, aux); +} + +static ssize_t ti_sn_aux_transfer(struct drm_dp_aux *aux, + struct drm_dp_aux_msg *msg) +{ + struct ti_sn65dsi86 *pdata = aux_to_ti_sn65dsi86(aux); + u32 request = msg->request & ~(DP_AUX_I2C_MOT | DP_AUX_I2C_WRITE_STATUS_UPDATE); + u32 request_val = AUX_CMD_REQ(msg->request); + u8 *buf = msg->buffer; + unsigned int len = msg->size; + unsigned int short_len; + unsigned int val; + int ret; + u8 addr_len[SN_AUX_LENGTH_REG + 1 - SN_AUX_ADDR_19_16_REG]; + + if (len > SN_AUX_MAX_PAYLOAD_BYTES) + return -EINVAL; + + pm_runtime_get_sync(pdata->dev); + mutex_lock(&pdata->comms_mutex); + + /* + * If someone tries to do a DDC over AUX transaction before pre_enable() + * on a device without a dedicated reference clock then we just can't + * do it. Fail right away. This prevents non-refclk users from reading + * the EDID before enabling the panel but such is life. + */ + if (!pdata->comms_enabled) { + ret = -EIO; + goto exit; + } + + switch (request) { + case DP_AUX_NATIVE_WRITE: + case DP_AUX_I2C_WRITE: + case DP_AUX_NATIVE_READ: + case DP_AUX_I2C_READ: + regmap_write(pdata->regmap, SN_AUX_CMD_REG, request_val); + /* Assume it's good */ + msg->reply = 0; + break; + default: + ret = -EINVAL; + goto exit; + } + + BUILD_BUG_ON(sizeof(addr_len) != sizeof(__be32)); + put_unaligned_be32((msg->address & SN_AUX_ADDR_MASK) << 8 | len, + addr_len); + regmap_bulk_write(pdata->regmap, SN_AUX_ADDR_19_16_REG, addr_len, + ARRAY_SIZE(addr_len)); + + if (request == DP_AUX_NATIVE_WRITE || request == DP_AUX_I2C_WRITE) + regmap_bulk_write(pdata->regmap, SN_AUX_WDATA_REG(0), buf, len); + + /* Clear old status bits before start so we don't get confused */ + regmap_write(pdata->regmap, SN_AUX_CMD_STATUS_REG, + AUX_IRQ_STATUS_NAT_I2C_FAIL | + AUX_IRQ_STATUS_AUX_RPLY_TOUT | + AUX_IRQ_STATUS_AUX_SHORT); + + regmap_write(pdata->regmap, SN_AUX_CMD_REG, request_val | AUX_CMD_SEND); + + /* Zero delay loop because i2c transactions are slow already */ + ret = regmap_read_poll_timeout(pdata->regmap, SN_AUX_CMD_REG, val, + !(val & AUX_CMD_SEND), 0, 50 * 1000); + if (ret) + goto exit; + + ret = regmap_read(pdata->regmap, SN_AUX_CMD_STATUS_REG, &val); + if (ret) + goto exit; + + if (val & AUX_IRQ_STATUS_AUX_RPLY_TOUT) { + /* + * The hardware tried the message seven times per the DP spec + * but it hit a timeout. We ignore defers here because they're + * handled in hardware. + */ + ret = -ETIMEDOUT; + goto exit; + } + + if (val & AUX_IRQ_STATUS_AUX_SHORT) { + ret = regmap_read(pdata->regmap, SN_AUX_LENGTH_REG, &short_len); + len = min(len, short_len); + if (ret) + goto exit; + } else if (val & AUX_IRQ_STATUS_NAT_I2C_FAIL) { + switch (request) { + case DP_AUX_I2C_WRITE: + case DP_AUX_I2C_READ: + msg->reply |= DP_AUX_I2C_REPLY_NACK; + break; + case DP_AUX_NATIVE_READ: + case DP_AUX_NATIVE_WRITE: + msg->reply |= DP_AUX_NATIVE_REPLY_NACK; + break; + } + len = 0; + goto exit; + } + + if (request != DP_AUX_NATIVE_WRITE && request != DP_AUX_I2C_WRITE && len != 0) + ret = regmap_bulk_read(pdata->regmap, SN_AUX_RDATA_REG(0), buf, len); + +exit: + mutex_unlock(&pdata->comms_mutex); + pm_runtime_mark_last_busy(pdata->dev); + pm_runtime_put_autosuspend(pdata->dev); + + if (ret) + return ret; + return len; +} + +static int ti_sn_aux_wait_hpd_asserted(struct drm_dp_aux *aux, unsigned long wait_us) +{ + /* + * The HPD in this chip is a bit useless (See comment in + * ti_sn65dsi86_enable_comms) so if our driver is expected to wait + * for HPD, we just assume it's asserted after the wait_us delay. + * + * In case we are asked to wait forever (wait_us=0) take conservative + * 500ms delay. + */ + if (wait_us == 0) + wait_us = 500000; + + usleep_range(wait_us, wait_us + 1000); + + return 0; +} + +static int ti_sn_aux_probe(struct auxiliary_device *adev, + const struct auxiliary_device_id *id) +{ + struct ti_sn65dsi86 *pdata = dev_get_drvdata(adev->dev.parent); + int ret; + + pdata->aux.name = "ti-sn65dsi86-aux"; + pdata->aux.dev = &adev->dev; + pdata->aux.transfer = ti_sn_aux_transfer; + pdata->aux.wait_hpd_asserted = ti_sn_aux_wait_hpd_asserted; + drm_dp_aux_init(&pdata->aux); + + ret = devm_of_dp_aux_populate_ep_devices(&pdata->aux); + if (ret) + return ret; + + /* + * The eDP to MIPI bridge parts don't work until the AUX channel is + * setup so we don't add it in the main driver probe, we add it now. + */ + return ti_sn65dsi86_add_aux_device(pdata, &pdata->bridge_aux, "bridge"); +} + +static const struct auxiliary_device_id ti_sn_aux_id_table[] = { + { .name = "ti_sn65dsi86.aux", }, + {}, +}; + +static struct auxiliary_driver ti_sn_aux_driver = { + .name = "aux", + .probe = ti_sn_aux_probe, + .id_table = ti_sn_aux_id_table, +}; + +/*------------------------------------------------------------------------------ + * DRM Bridge + */ + +static struct ti_sn65dsi86 *bridge_to_ti_sn65dsi86(struct drm_bridge *bridge) +{ + return container_of(bridge, struct ti_sn65dsi86, bridge); +} + +static int ti_sn_attach_host(struct auxiliary_device *adev, struct ti_sn65dsi86 *pdata) +{ + int val; + struct mipi_dsi_host *host; + struct mipi_dsi_device *dsi; + struct device *dev = pdata->dev; + const struct mipi_dsi_device_info info = { .type = "ti_sn_bridge", + .channel = 0, + .node = NULL, + }; + + host = of_find_mipi_dsi_host_by_node(pdata->host_node); + if (!host) + return -EPROBE_DEFER; + + dsi = devm_mipi_dsi_device_register_full(&adev->dev, host, &info); + if (IS_ERR(dsi)) + return PTR_ERR(dsi); + + /* TODO: setting to 4 MIPI lanes always for now */ + dsi->lanes = 4; + dsi->format = MIPI_DSI_FMT_RGB888; + dsi->mode_flags = MIPI_DSI_MODE_VIDEO; + + /* check if continuous dsi clock is required or not */ + pm_runtime_get_sync(dev); + regmap_read(pdata->regmap, SN_DPPLL_SRC_REG, &val); + pm_runtime_put_autosuspend(dev); + if (!(val & DPPLL_CLK_SRC_DSICLK)) + dsi->mode_flags |= MIPI_DSI_CLOCK_NON_CONTINUOUS; + + pdata->dsi = dsi; + + return devm_mipi_dsi_attach(&adev->dev, dsi); +} + +static int ti_sn_bridge_attach(struct drm_bridge *bridge, + enum drm_bridge_attach_flags flags) +{ + struct ti_sn65dsi86 *pdata = bridge_to_ti_sn65dsi86(bridge); + int ret; + + pdata->aux.drm_dev = bridge->dev; + ret = drm_dp_aux_register(&pdata->aux); + if (ret < 0) { + drm_err(bridge->dev, "Failed to register DP AUX channel: %d\n", ret); + return ret; + } + + /* + * Attach the next bridge. + * We never want the next bridge to *also* create a connector. + */ + ret = drm_bridge_attach(bridge->encoder, pdata->next_bridge, + &pdata->bridge, flags | DRM_BRIDGE_ATTACH_NO_CONNECTOR); + if (ret < 0) + goto err_initted_aux; + + if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) + return 0; + + pdata->connector = drm_bridge_connector_init(pdata->bridge.dev, + pdata->bridge.encoder); + if (IS_ERR(pdata->connector)) { + ret = PTR_ERR(pdata->connector); + goto err_initted_aux; + } + + drm_connector_attach_encoder(pdata->connector, pdata->bridge.encoder); + + return 0; + +err_initted_aux: + drm_dp_aux_unregister(&pdata->aux); + return ret; +} + +static void ti_sn_bridge_detach(struct drm_bridge *bridge) +{ + drm_dp_aux_unregister(&bridge_to_ti_sn65dsi86(bridge)->aux); +} + +static enum drm_mode_status +ti_sn_bridge_mode_valid(struct drm_bridge *bridge, + const struct drm_display_info *info, + const struct drm_display_mode *mode) +{ + /* maximum supported resolution is 4K at 60 fps */ + if (mode->clock > 594000) + return MODE_CLOCK_HIGH; + + /* + * The front and back porch registers are 8 bits, and pulse width + * registers are 15 bits, so reject any modes with larger periods. + */ + + if ((mode->hsync_start - mode->hdisplay) > 0xff) + return MODE_HBLANK_WIDE; + + if ((mode->vsync_start - mode->vdisplay) > 0xff) + return MODE_VBLANK_WIDE; + + if ((mode->hsync_end - mode->hsync_start) > 0x7fff) + return MODE_HSYNC_WIDE; + + if ((mode->vsync_end - mode->vsync_start) > 0x7fff) + return MODE_VSYNC_WIDE; + + if ((mode->htotal - mode->hsync_end) > 0xff) + return MODE_HBLANK_WIDE; + + if ((mode->vtotal - mode->vsync_end) > 0xff) + return MODE_VBLANK_WIDE; + + return MODE_OK; +} + +static void ti_sn_bridge_atomic_disable(struct drm_bridge *bridge, + struct drm_bridge_state *old_bridge_state) +{ + struct ti_sn65dsi86 *pdata = bridge_to_ti_sn65dsi86(bridge); + + /* disable video stream */ + regmap_update_bits(pdata->regmap, SN_ENH_FRAME_REG, VSTREAM_ENABLE, 0); +} + +static void ti_sn_bridge_set_dsi_rate(struct ti_sn65dsi86 *pdata) +{ + unsigned int bit_rate_mhz, clk_freq_mhz; + unsigned int val; + struct drm_display_mode *mode = + &pdata->bridge.encoder->crtc->state->adjusted_mode; + + /* set DSIA clk frequency */ + bit_rate_mhz = (mode->clock / 1000) * + mipi_dsi_pixel_format_to_bpp(pdata->dsi->format); + clk_freq_mhz = bit_rate_mhz / (pdata->dsi->lanes * 2); + + /* for each increment in val, frequency increases by 5MHz */ + val = (MIN_DSI_CLK_FREQ_MHZ / 5) + + (((clk_freq_mhz - MIN_DSI_CLK_FREQ_MHZ) / 5) & 0xFF); + regmap_write(pdata->regmap, SN_DSIA_CLK_FREQ_REG, val); +} + +static unsigned int ti_sn_bridge_get_bpp(struct drm_connector *connector) +{ + if (connector->display_info.bpc <= 6) + return 18; + else + return 24; +} + +/* + * LUT index corresponds to register value and + * LUT values corresponds to dp data rate supported + * by the bridge in Mbps unit. + */ +static const unsigned int ti_sn_bridge_dp_rate_lut[] = { + 0, 1620, 2160, 2430, 2700, 3240, 4320, 5400 +}; + +static int ti_sn_bridge_calc_min_dp_rate_idx(struct ti_sn65dsi86 *pdata, unsigned int bpp) +{ + unsigned int bit_rate_khz, dp_rate_mhz; + unsigned int i; + struct drm_display_mode *mode = + &pdata->bridge.encoder->crtc->state->adjusted_mode; + + /* Calculate minimum bit rate based on our pixel clock. */ + bit_rate_khz = mode->clock * bpp; + + /* Calculate minimum DP data rate, taking 80% as per DP spec */ + dp_rate_mhz = DIV_ROUND_UP(bit_rate_khz * DP_CLK_FUDGE_NUM, + 1000 * pdata->dp_lanes * DP_CLK_FUDGE_DEN); + + for (i = 1; i < ARRAY_SIZE(ti_sn_bridge_dp_rate_lut) - 1; i++) + if (ti_sn_bridge_dp_rate_lut[i] >= dp_rate_mhz) + break; + + return i; +} + +static unsigned int ti_sn_bridge_read_valid_rates(struct ti_sn65dsi86 *pdata) +{ + unsigned int valid_rates = 0; + unsigned int rate_per_200khz; + unsigned int rate_mhz; + u8 dpcd_val; + int ret; + int i, j; + + ret = drm_dp_dpcd_readb(&pdata->aux, DP_EDP_DPCD_REV, &dpcd_val); + if (ret != 1) { + DRM_DEV_ERROR(pdata->dev, + "Can't read eDP rev (%d), assuming 1.1\n", ret); + dpcd_val = DP_EDP_11; + } + + if (dpcd_val >= DP_EDP_14) { + /* eDP 1.4 devices must provide a custom table */ + __le16 sink_rates[DP_MAX_SUPPORTED_RATES]; + + ret = drm_dp_dpcd_read(&pdata->aux, DP_SUPPORTED_LINK_RATES, + sink_rates, sizeof(sink_rates)); + + if (ret != sizeof(sink_rates)) { + DRM_DEV_ERROR(pdata->dev, + "Can't read supported rate table (%d)\n", ret); + + /* By zeroing we'll fall back to DP_MAX_LINK_RATE. */ + memset(sink_rates, 0, sizeof(sink_rates)); + } + + for (i = 0; i < ARRAY_SIZE(sink_rates); i++) { + rate_per_200khz = le16_to_cpu(sink_rates[i]); + + if (!rate_per_200khz) + break; + + rate_mhz = rate_per_200khz * 200 / 1000; + for (j = 0; + j < ARRAY_SIZE(ti_sn_bridge_dp_rate_lut); + j++) { + if (ti_sn_bridge_dp_rate_lut[j] == rate_mhz) + valid_rates |= BIT(j); + } + } + + for (i = 0; i < ARRAY_SIZE(ti_sn_bridge_dp_rate_lut); i++) { + if (valid_rates & BIT(i)) + return valid_rates; + } + DRM_DEV_ERROR(pdata->dev, + "No matching eDP rates in table; falling back\n"); + } + + /* On older versions best we can do is use DP_MAX_LINK_RATE */ + ret = drm_dp_dpcd_readb(&pdata->aux, DP_MAX_LINK_RATE, &dpcd_val); + if (ret != 1) { + DRM_DEV_ERROR(pdata->dev, + "Can't read max rate (%d); assuming 5.4 GHz\n", + ret); + dpcd_val = DP_LINK_BW_5_4; + } + + switch (dpcd_val) { + default: + DRM_DEV_ERROR(pdata->dev, + "Unexpected max rate (%#x); assuming 5.4 GHz\n", + (int)dpcd_val); + fallthrough; + case DP_LINK_BW_5_4: + valid_rates |= BIT(7); + fallthrough; + case DP_LINK_BW_2_7: + valid_rates |= BIT(4); + fallthrough; + case DP_LINK_BW_1_62: + valid_rates |= BIT(1); + break; + } + + return valid_rates; +} + +static void ti_sn_bridge_set_video_timings(struct ti_sn65dsi86 *pdata) +{ + struct drm_display_mode *mode = + &pdata->bridge.encoder->crtc->state->adjusted_mode; + u8 hsync_polarity = 0, vsync_polarity = 0; + + if (mode->flags & DRM_MODE_FLAG_NHSYNC) + hsync_polarity = CHA_HSYNC_POLARITY; + if (mode->flags & DRM_MODE_FLAG_NVSYNC) + vsync_polarity = CHA_VSYNC_POLARITY; + + ti_sn65dsi86_write_u16(pdata, SN_CHA_ACTIVE_LINE_LENGTH_LOW_REG, + mode->hdisplay); + ti_sn65dsi86_write_u16(pdata, SN_CHA_VERTICAL_DISPLAY_SIZE_LOW_REG, + mode->vdisplay); + regmap_write(pdata->regmap, SN_CHA_HSYNC_PULSE_WIDTH_LOW_REG, + (mode->hsync_end - mode->hsync_start) & 0xFF); + regmap_write(pdata->regmap, SN_CHA_HSYNC_PULSE_WIDTH_HIGH_REG, + (((mode->hsync_end - mode->hsync_start) >> 8) & 0x7F) | + hsync_polarity); + regmap_write(pdata->regmap, SN_CHA_VSYNC_PULSE_WIDTH_LOW_REG, + (mode->vsync_end - mode->vsync_start) & 0xFF); + regmap_write(pdata->regmap, SN_CHA_VSYNC_PULSE_WIDTH_HIGH_REG, + (((mode->vsync_end - mode->vsync_start) >> 8) & 0x7F) | + vsync_polarity); + + regmap_write(pdata->regmap, SN_CHA_HORIZONTAL_BACK_PORCH_REG, + (mode->htotal - mode->hsync_end) & 0xFF); + regmap_write(pdata->regmap, SN_CHA_VERTICAL_BACK_PORCH_REG, + (mode->vtotal - mode->vsync_end) & 0xFF); + + regmap_write(pdata->regmap, SN_CHA_HORIZONTAL_FRONT_PORCH_REG, + (mode->hsync_start - mode->hdisplay) & 0xFF); + regmap_write(pdata->regmap, SN_CHA_VERTICAL_FRONT_PORCH_REG, + (mode->vsync_start - mode->vdisplay) & 0xFF); + + usleep_range(10000, 10500); /* 10ms delay recommended by spec */ +} + +static unsigned int ti_sn_get_max_lanes(struct ti_sn65dsi86 *pdata) +{ + u8 data; + int ret; + + ret = drm_dp_dpcd_readb(&pdata->aux, DP_MAX_LANE_COUNT, &data); + if (ret != 1) { + DRM_DEV_ERROR(pdata->dev, + "Can't read lane count (%d); assuming 4\n", ret); + return 4; + } + + return data & DP_LANE_COUNT_MASK; +} + +static int ti_sn_link_training(struct ti_sn65dsi86 *pdata, int dp_rate_idx, + const char **last_err_str) +{ + unsigned int val; + int ret; + int i; + + /* set dp clk frequency value */ + regmap_update_bits(pdata->regmap, SN_DATARATE_CONFIG_REG, + DP_DATARATE_MASK, DP_DATARATE(dp_rate_idx)); + + /* enable DP PLL */ + regmap_write(pdata->regmap, SN_PLL_ENABLE_REG, 1); + + ret = regmap_read_poll_timeout(pdata->regmap, SN_DPPLL_SRC_REG, val, + val & DPPLL_SRC_DP_PLL_LOCK, 1000, + 50 * 1000); + if (ret) { + *last_err_str = "DP_PLL_LOCK polling failed"; + goto exit; + } + + /* + * We'll try to link train several times. As part of link training + * the bridge chip will write DP_SET_POWER_D0 to DP_SET_POWER. If + * the panel isn't ready quite it might respond NAK here which means + * we need to try again. + */ + for (i = 0; i < SN_LINK_TRAINING_TRIES; i++) { + /* Semi auto link training mode */ + regmap_write(pdata->regmap, SN_ML_TX_MODE_REG, 0x0A); + ret = regmap_read_poll_timeout(pdata->regmap, SN_ML_TX_MODE_REG, val, + val == ML_TX_MAIN_LINK_OFF || + val == ML_TX_NORMAL_MODE, 1000, + 500 * 1000); + if (ret) { + *last_err_str = "Training complete polling failed"; + } else if (val == ML_TX_MAIN_LINK_OFF) { + *last_err_str = "Link training failed, link is off"; + ret = -EIO; + continue; + } + + break; + } + + /* If we saw quite a few retries, add a note about it */ + if (!ret && i > SN_LINK_TRAINING_TRIES / 2) + DRM_DEV_INFO(pdata->dev, "Link training needed %d retries\n", i); + +exit: + /* Disable the PLL if we failed */ + if (ret) + regmap_write(pdata->regmap, SN_PLL_ENABLE_REG, 0); + + return ret; +} + +static void ti_sn_bridge_atomic_enable(struct drm_bridge *bridge, + struct drm_bridge_state *old_bridge_state) +{ + struct ti_sn65dsi86 *pdata = bridge_to_ti_sn65dsi86(bridge); + struct drm_connector *connector; + const char *last_err_str = "No supported DP rate"; + unsigned int valid_rates; + int dp_rate_idx; + unsigned int val; + int ret = -EINVAL; + int max_dp_lanes; + unsigned int bpp; + + connector = drm_atomic_get_new_connector_for_encoder(old_bridge_state->base.state, + bridge->encoder); + if (!connector) { + dev_err_ratelimited(pdata->dev, "Could not get the connector\n"); + return; + } + + max_dp_lanes = ti_sn_get_max_lanes(pdata); + pdata->dp_lanes = min(pdata->dp_lanes, max_dp_lanes); + + /* DSI_A lane config */ + val = CHA_DSI_LANES(SN_MAX_DP_LANES - pdata->dsi->lanes); + regmap_update_bits(pdata->regmap, SN_DSI_LANES_REG, + CHA_DSI_LANES_MASK, val); + + regmap_write(pdata->regmap, SN_LN_ASSIGN_REG, pdata->ln_assign); + regmap_update_bits(pdata->regmap, SN_ENH_FRAME_REG, LN_POLRS_MASK, + pdata->ln_polrs << LN_POLRS_OFFSET); + + /* set dsi clk frequency value */ + ti_sn_bridge_set_dsi_rate(pdata); + + /* + * The SN65DSI86 only supports ASSR Display Authentication method and + * this method is enabled for eDP panels. An eDP panel must support this + * authentication method. We need to enable this method in the eDP panel + * at DisplayPort address 0x0010A prior to link training. + * + * As only ASSR is supported by SN65DSI86, for full DisplayPort displays + * we need to disable the scrambler. + */ + if (pdata->bridge.type == DRM_MODE_CONNECTOR_eDP) { + drm_dp_dpcd_writeb(&pdata->aux, DP_EDP_CONFIGURATION_SET, + DP_ALTERNATE_SCRAMBLER_RESET_ENABLE); + + regmap_update_bits(pdata->regmap, SN_TRAINING_SETTING_REG, + SCRAMBLE_DISABLE, 0); + } else { + regmap_update_bits(pdata->regmap, SN_TRAINING_SETTING_REG, + SCRAMBLE_DISABLE, SCRAMBLE_DISABLE); + } + + bpp = ti_sn_bridge_get_bpp(connector); + /* Set the DP output format (18 bpp or 24 bpp) */ + val = bpp == 18 ? BPP_18_RGB : 0; + regmap_update_bits(pdata->regmap, SN_DATA_FORMAT_REG, BPP_18_RGB, val); + + /* DP lane config */ + val = DP_NUM_LANES(min(pdata->dp_lanes, 3)); + regmap_update_bits(pdata->regmap, SN_SSC_CONFIG_REG, DP_NUM_LANES_MASK, + val); + + valid_rates = ti_sn_bridge_read_valid_rates(pdata); + + /* Train until we run out of rates */ + for (dp_rate_idx = ti_sn_bridge_calc_min_dp_rate_idx(pdata, bpp); + dp_rate_idx < ARRAY_SIZE(ti_sn_bridge_dp_rate_lut); + dp_rate_idx++) { + if (!(valid_rates & BIT(dp_rate_idx))) + continue; + + ret = ti_sn_link_training(pdata, dp_rate_idx, &last_err_str); + if (!ret) + break; + } + if (ret) { + DRM_DEV_ERROR(pdata->dev, "%s (%d)\n", last_err_str, ret); + return; + } + + /* config video parameters */ + ti_sn_bridge_set_video_timings(pdata); + + /* enable video stream */ + regmap_update_bits(pdata->regmap, SN_ENH_FRAME_REG, VSTREAM_ENABLE, + VSTREAM_ENABLE); +} + +static void ti_sn_bridge_atomic_pre_enable(struct drm_bridge *bridge, + struct drm_bridge_state *old_bridge_state) +{ + struct ti_sn65dsi86 *pdata = bridge_to_ti_sn65dsi86(bridge); + + pm_runtime_get_sync(pdata->dev); + + if (!pdata->refclk) + ti_sn65dsi86_enable_comms(pdata); + + /* td7: min 100 us after enable before DSI data */ + usleep_range(100, 110); +} + +static void ti_sn_bridge_atomic_post_disable(struct drm_bridge *bridge, + struct drm_bridge_state *old_bridge_state) +{ + struct ti_sn65dsi86 *pdata = bridge_to_ti_sn65dsi86(bridge); + + /* semi auto link training mode OFF */ + regmap_write(pdata->regmap, SN_ML_TX_MODE_REG, 0); + /* Num lanes to 0 as per power sequencing in data sheet */ + regmap_update_bits(pdata->regmap, SN_SSC_CONFIG_REG, DP_NUM_LANES_MASK, 0); + /* disable DP PLL */ + regmap_write(pdata->regmap, SN_PLL_ENABLE_REG, 0); + + if (!pdata->refclk) + ti_sn65dsi86_disable_comms(pdata); + + pm_runtime_put_sync(pdata->dev); +} + +static enum drm_connector_status ti_sn_bridge_detect(struct drm_bridge *bridge) +{ + struct ti_sn65dsi86 *pdata = bridge_to_ti_sn65dsi86(bridge); + int val = 0; + + pm_runtime_get_sync(pdata->dev); + regmap_read(pdata->regmap, SN_HPD_DISABLE_REG, &val); + pm_runtime_put_autosuspend(pdata->dev); + + return val & HPD_DEBOUNCED_STATE ? connector_status_connected + : connector_status_disconnected; +} + +static struct edid *ti_sn_bridge_get_edid(struct drm_bridge *bridge, + struct drm_connector *connector) +{ + struct ti_sn65dsi86 *pdata = bridge_to_ti_sn65dsi86(bridge); + + return drm_get_edid(connector, &pdata->aux.ddc); +} + +static const struct drm_bridge_funcs ti_sn_bridge_funcs = { + .attach = ti_sn_bridge_attach, + .detach = ti_sn_bridge_detach, + .mode_valid = ti_sn_bridge_mode_valid, + .get_edid = ti_sn_bridge_get_edid, + .detect = ti_sn_bridge_detect, + .atomic_pre_enable = ti_sn_bridge_atomic_pre_enable, + .atomic_enable = ti_sn_bridge_atomic_enable, + .atomic_disable = ti_sn_bridge_atomic_disable, + .atomic_post_disable = ti_sn_bridge_atomic_post_disable, + .atomic_reset = drm_atomic_helper_bridge_reset, + .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state, +}; + +static void ti_sn_bridge_parse_lanes(struct ti_sn65dsi86 *pdata, + struct device_node *np) +{ + u32 lane_assignments[SN_MAX_DP_LANES] = { 0, 1, 2, 3 }; + u32 lane_polarities[SN_MAX_DP_LANES] = { }; + struct device_node *endpoint; + u8 ln_assign = 0; + u8 ln_polrs = 0; + int dp_lanes; + int i; + + /* + * Read config from the device tree about lane remapping and lane + * polarities. These are optional and we assume identity map and + * normal polarity if nothing is specified. It's OK to specify just + * data-lanes but not lane-polarities but not vice versa. + * + * Error checking is light (we just make sure we don't crash or + * buffer overrun) and we assume dts is well formed and specifying + * mappings that the hardware supports. + */ + endpoint = of_graph_get_endpoint_by_regs(np, 1, -1); + dp_lanes = drm_of_get_data_lanes_count(endpoint, 1, SN_MAX_DP_LANES); + if (dp_lanes > 0) { + of_property_read_u32_array(endpoint, "data-lanes", + lane_assignments, dp_lanes); + of_property_read_u32_array(endpoint, "lane-polarities", + lane_polarities, dp_lanes); + } else { + dp_lanes = SN_MAX_DP_LANES; + } + of_node_put(endpoint); + + /* + * Convert into register format. Loop over all lanes even if + * data-lanes had fewer elements so that we nicely initialize + * the LN_ASSIGN register. + */ + for (i = SN_MAX_DP_LANES - 1; i >= 0; i--) { + ln_assign = ln_assign << LN_ASSIGN_WIDTH | lane_assignments[i]; + ln_polrs = ln_polrs << 1 | lane_polarities[i]; + } + + /* Stash in our struct for when we power on */ + pdata->dp_lanes = dp_lanes; + pdata->ln_assign = ln_assign; + pdata->ln_polrs = ln_polrs; +} + +static int ti_sn_bridge_parse_dsi_host(struct ti_sn65dsi86 *pdata) +{ + struct device_node *np = pdata->dev->of_node; + + pdata->host_node = of_graph_get_remote_node(np, 0, 0); + + if (!pdata->host_node) { + DRM_ERROR("remote dsi host node not found\n"); + return -ENODEV; + } + + return 0; +} + +static int ti_sn_bridge_probe(struct auxiliary_device *adev, + const struct auxiliary_device_id *id) +{ + struct ti_sn65dsi86 *pdata = dev_get_drvdata(adev->dev.parent); + struct device_node *np = pdata->dev->of_node; + int ret; + + pdata->next_bridge = devm_drm_of_get_bridge(&adev->dev, np, 1, 0); + if (IS_ERR(pdata->next_bridge)) + return dev_err_probe(&adev->dev, PTR_ERR(pdata->next_bridge), + "failed to create panel bridge\n"); + + ti_sn_bridge_parse_lanes(pdata, np); + + ret = ti_sn_bridge_parse_dsi_host(pdata); + if (ret) + return ret; + + pdata->bridge.funcs = &ti_sn_bridge_funcs; + pdata->bridge.of_node = np; + pdata->bridge.type = pdata->next_bridge->type == DRM_MODE_CONNECTOR_DisplayPort + ? DRM_MODE_CONNECTOR_DisplayPort : DRM_MODE_CONNECTOR_eDP; + + if (pdata->bridge.type == DRM_MODE_CONNECTOR_DisplayPort) + pdata->bridge.ops = DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_DETECT; + + drm_bridge_add(&pdata->bridge); + + ret = ti_sn_attach_host(adev, pdata); + if (ret) { + dev_err_probe(&adev->dev, ret, "failed to attach dsi host\n"); + goto err_remove_bridge; + } + + return 0; + +err_remove_bridge: + drm_bridge_remove(&pdata->bridge); + return ret; +} + +static void ti_sn_bridge_remove(struct auxiliary_device *adev) +{ + struct ti_sn65dsi86 *pdata = dev_get_drvdata(adev->dev.parent); + + if (!pdata) + return; + + drm_bridge_remove(&pdata->bridge); + + of_node_put(pdata->host_node); +} + +static const struct auxiliary_device_id ti_sn_bridge_id_table[] = { + { .name = "ti_sn65dsi86.bridge", }, + {}, +}; + +static struct auxiliary_driver ti_sn_bridge_driver = { + .name = "bridge", + .probe = ti_sn_bridge_probe, + .remove = ti_sn_bridge_remove, + .id_table = ti_sn_bridge_id_table, +}; + +/* ----------------------------------------------------------------------------- + * PWM Controller + */ +#if defined(CONFIG_PWM) +static int ti_sn_pwm_pin_request(struct ti_sn65dsi86 *pdata) +{ + return atomic_xchg(&pdata->pwm_pin_busy, 1) ? -EBUSY : 0; +} + +static void ti_sn_pwm_pin_release(struct ti_sn65dsi86 *pdata) +{ + atomic_set(&pdata->pwm_pin_busy, 0); +} + +static struct ti_sn65dsi86 *pwm_chip_to_ti_sn_bridge(struct pwm_chip *chip) +{ + return container_of(chip, struct ti_sn65dsi86, pchip); +} + +static int ti_sn_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm) +{ + struct ti_sn65dsi86 *pdata = pwm_chip_to_ti_sn_bridge(chip); + + return ti_sn_pwm_pin_request(pdata); +} + +static void ti_sn_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm) +{ + struct ti_sn65dsi86 *pdata = pwm_chip_to_ti_sn_bridge(chip); + + ti_sn_pwm_pin_release(pdata); +} + +/* + * Limitations: + * - The PWM signal is not driven when the chip is powered down, or in its + * reset state and the driver does not implement the "suspend state" + * described in the documentation. In order to save power, state->enabled is + * interpreted as denoting if the signal is expected to be valid, and is used + * to determine if the chip needs to be kept powered. + * - Changing both period and duty_cycle is not done atomically, neither is the + * multi-byte register updates, so the output might briefly be undefined + * during update. + */ +static int ti_sn_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, + const struct pwm_state *state) +{ + struct ti_sn65dsi86 *pdata = pwm_chip_to_ti_sn_bridge(chip); + unsigned int pwm_en_inv; + unsigned int backlight; + unsigned int pre_div; + unsigned int scale; + u64 period_max; + u64 period; + int ret; + + if (!pdata->pwm_enabled) { + ret = pm_runtime_get_sync(pdata->dev); + if (ret < 0) { + pm_runtime_put_sync(pdata->dev); + return ret; + } + } + + if (state->enabled) { + if (!pdata->pwm_enabled) { + /* + * The chip might have been powered down while we + * didn't hold a PM runtime reference, so mux in the + * PWM function on the GPIO pin again. + */ + ret = regmap_update_bits(pdata->regmap, SN_GPIO_CTRL_REG, + SN_GPIO_MUX_MASK << (2 * SN_PWM_GPIO_IDX), + SN_GPIO_MUX_SPECIAL << (2 * SN_PWM_GPIO_IDX)); + if (ret) { + dev_err(pdata->dev, "failed to mux in PWM function\n"); + goto out; + } + } + + /* + * Per the datasheet the PWM frequency is given by: + * + * REFCLK_FREQ + * PWM_FREQ = ----------------------------------- + * PWM_PRE_DIV * BACKLIGHT_SCALE + 1 + * + * However, after careful review the author is convinced that + * the documentation has lost some parenthesis around + * "BACKLIGHT_SCALE + 1". + * + * With the period T_pwm = 1/PWM_FREQ this can be written: + * + * T_pwm * REFCLK_FREQ = PWM_PRE_DIV * (BACKLIGHT_SCALE + 1) + * + * In order to keep BACKLIGHT_SCALE within its 16 bits, + * PWM_PRE_DIV must be: + * + * T_pwm * REFCLK_FREQ + * PWM_PRE_DIV >= ------------------------- + * BACKLIGHT_SCALE_MAX + 1 + * + * To simplify the search and to favour higher resolution of + * the duty cycle over accuracy of the period, the lowest + * possible PWM_PRE_DIV is used. Finally the scale is + * calculated as: + * + * T_pwm * REFCLK_FREQ + * BACKLIGHT_SCALE = ---------------------- - 1 + * PWM_PRE_DIV + * + * Here T_pwm is represented in seconds, so appropriate scaling + * to nanoseconds is necessary. + */ + + /* Minimum T_pwm is 1 / REFCLK_FREQ */ + if (state->period <= NSEC_PER_SEC / pdata->pwm_refclk_freq) { + ret = -EINVAL; + goto out; + } + + /* + * Maximum T_pwm is 255 * (65535 + 1) / REFCLK_FREQ + * Limit period to this to avoid overflows + */ + period_max = div_u64((u64)NSEC_PER_SEC * 255 * (65535 + 1), + pdata->pwm_refclk_freq); + period = min(state->period, period_max); + + pre_div = DIV64_U64_ROUND_UP(period * pdata->pwm_refclk_freq, + (u64)NSEC_PER_SEC * (BACKLIGHT_SCALE_MAX + 1)); + scale = div64_u64(period * pdata->pwm_refclk_freq, (u64)NSEC_PER_SEC * pre_div) - 1; + + /* + * The documentation has the duty ratio given as: + * + * duty BACKLIGHT + * ------- = --------------------- + * period BACKLIGHT_SCALE + 1 + * + * Solve for BACKLIGHT, substituting BACKLIGHT_SCALE according + * to definition above and adjusting for nanosecond + * representation of duty cycle gives us: + */ + backlight = div64_u64(state->duty_cycle * pdata->pwm_refclk_freq, + (u64)NSEC_PER_SEC * pre_div); + if (backlight > scale) + backlight = scale; + + ret = regmap_write(pdata->regmap, SN_PWM_PRE_DIV_REG, pre_div); + if (ret) { + dev_err(pdata->dev, "failed to update PWM_PRE_DIV\n"); + goto out; + } + + ti_sn65dsi86_write_u16(pdata, SN_BACKLIGHT_SCALE_REG, scale); + ti_sn65dsi86_write_u16(pdata, SN_BACKLIGHT_REG, backlight); + } + + pwm_en_inv = FIELD_PREP(SN_PWM_EN_MASK, state->enabled) | + FIELD_PREP(SN_PWM_INV_MASK, state->polarity == PWM_POLARITY_INVERSED); + ret = regmap_write(pdata->regmap, SN_PWM_EN_INV_REG, pwm_en_inv); + if (ret) { + dev_err(pdata->dev, "failed to update PWM_EN/PWM_INV\n"); + goto out; + } + + pdata->pwm_enabled = state->enabled; +out: + + if (!pdata->pwm_enabled) + pm_runtime_put_sync(pdata->dev); + + return ret; +} + +static int ti_sn_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm, + struct pwm_state *state) +{ + struct ti_sn65dsi86 *pdata = pwm_chip_to_ti_sn_bridge(chip); + unsigned int pwm_en_inv; + unsigned int pre_div; + u16 backlight; + u16 scale; + int ret; + + ret = regmap_read(pdata->regmap, SN_PWM_EN_INV_REG, &pwm_en_inv); + if (ret) + return ret; + + ret = ti_sn65dsi86_read_u16(pdata, SN_BACKLIGHT_SCALE_REG, &scale); + if (ret) + return ret; + + ret = ti_sn65dsi86_read_u16(pdata, SN_BACKLIGHT_REG, &backlight); + if (ret) + return ret; + + ret = regmap_read(pdata->regmap, SN_PWM_PRE_DIV_REG, &pre_div); + if (ret) + return ret; + + state->enabled = FIELD_GET(SN_PWM_EN_MASK, pwm_en_inv); + if (FIELD_GET(SN_PWM_INV_MASK, pwm_en_inv)) + state->polarity = PWM_POLARITY_INVERSED; + else + state->polarity = PWM_POLARITY_NORMAL; + + state->period = DIV_ROUND_UP_ULL((u64)NSEC_PER_SEC * pre_div * (scale + 1), + pdata->pwm_refclk_freq); + state->duty_cycle = DIV_ROUND_UP_ULL((u64)NSEC_PER_SEC * pre_div * backlight, + pdata->pwm_refclk_freq); + + if (state->duty_cycle > state->period) + state->duty_cycle = state->period; + + return 0; +} + +static const struct pwm_ops ti_sn_pwm_ops = { + .request = ti_sn_pwm_request, + .free = ti_sn_pwm_free, + .apply = ti_sn_pwm_apply, + .get_state = ti_sn_pwm_get_state, + .owner = THIS_MODULE, +}; + +static int ti_sn_pwm_probe(struct auxiliary_device *adev, + const struct auxiliary_device_id *id) +{ + struct ti_sn65dsi86 *pdata = dev_get_drvdata(adev->dev.parent); + + pdata->pchip.dev = pdata->dev; + pdata->pchip.ops = &ti_sn_pwm_ops; + pdata->pchip.npwm = 1; + pdata->pchip.of_xlate = of_pwm_single_xlate; + pdata->pchip.of_pwm_n_cells = 1; + + return pwmchip_add(&pdata->pchip); +} + +static void ti_sn_pwm_remove(struct auxiliary_device *adev) +{ + struct ti_sn65dsi86 *pdata = dev_get_drvdata(adev->dev.parent); + + pwmchip_remove(&pdata->pchip); + + if (pdata->pwm_enabled) + pm_runtime_put_sync(pdata->dev); +} + +static const struct auxiliary_device_id ti_sn_pwm_id_table[] = { + { .name = "ti_sn65dsi86.pwm", }, + {}, +}; + +static struct auxiliary_driver ti_sn_pwm_driver = { + .name = "pwm", + .probe = ti_sn_pwm_probe, + .remove = ti_sn_pwm_remove, + .id_table = ti_sn_pwm_id_table, +}; + +static int __init ti_sn_pwm_register(void) +{ + return auxiliary_driver_register(&ti_sn_pwm_driver); +} + +static void ti_sn_pwm_unregister(void) +{ + auxiliary_driver_unregister(&ti_sn_pwm_driver); +} + +#else +static inline int ti_sn_pwm_pin_request(struct ti_sn65dsi86 *pdata) { return 0; } +static inline void ti_sn_pwm_pin_release(struct ti_sn65dsi86 *pdata) {} + +static inline int ti_sn_pwm_register(void) { return 0; } +static inline void ti_sn_pwm_unregister(void) {} +#endif + +/* ----------------------------------------------------------------------------- + * GPIO Controller + */ +#if defined(CONFIG_OF_GPIO) + +static int tn_sn_bridge_of_xlate(struct gpio_chip *chip, + const struct of_phandle_args *gpiospec, + u32 *flags) +{ + if (WARN_ON(gpiospec->args_count < chip->of_gpio_n_cells)) + return -EINVAL; + + if (gpiospec->args[0] > chip->ngpio || gpiospec->args[0] < 1) + return -EINVAL; + + if (flags) + *flags = gpiospec->args[1]; + + return gpiospec->args[0] - SN_GPIO_PHYSICAL_OFFSET; +} + +static int ti_sn_bridge_gpio_get_direction(struct gpio_chip *chip, + unsigned int offset) +{ + struct ti_sn65dsi86 *pdata = gpiochip_get_data(chip); + + /* + * We already have to keep track of the direction because we use + * that to figure out whether we've powered the device. We can + * just return that rather than (maybe) powering up the device + * to ask its direction. + */ + return test_bit(offset, pdata->gchip_output) ? + GPIO_LINE_DIRECTION_OUT : GPIO_LINE_DIRECTION_IN; +} + +static int ti_sn_bridge_gpio_get(struct gpio_chip *chip, unsigned int offset) +{ + struct ti_sn65dsi86 *pdata = gpiochip_get_data(chip); + unsigned int val; + int ret; + + /* + * When the pin is an input we don't forcibly keep the bridge + * powered--we just power it on to read the pin. NOTE: part of + * the reason this works is that the bridge defaults (when + * powered back on) to all 4 GPIOs being configured as GPIO input. + * Also note that if something else is keeping the chip powered the + * pm_runtime functions are lightweight increments of a refcount. + */ + pm_runtime_get_sync(pdata->dev); + ret = regmap_read(pdata->regmap, SN_GPIO_IO_REG, &val); + pm_runtime_put_autosuspend(pdata->dev); + + if (ret) + return ret; + + return !!(val & BIT(SN_GPIO_INPUT_SHIFT + offset)); +} + +static void ti_sn_bridge_gpio_set(struct gpio_chip *chip, unsigned int offset, + int val) +{ + struct ti_sn65dsi86 *pdata = gpiochip_get_data(chip); + int ret; + + if (!test_bit(offset, pdata->gchip_output)) { + dev_err(pdata->dev, "Ignoring GPIO set while input\n"); + return; + } + + val &= 1; + ret = regmap_update_bits(pdata->regmap, SN_GPIO_IO_REG, + BIT(SN_GPIO_OUTPUT_SHIFT + offset), + val << (SN_GPIO_OUTPUT_SHIFT + offset)); + if (ret) + dev_warn(pdata->dev, + "Failed to set bridge GPIO %u: %d\n", offset, ret); +} + +static int ti_sn_bridge_gpio_direction_input(struct gpio_chip *chip, + unsigned int offset) +{ + struct ti_sn65dsi86 *pdata = gpiochip_get_data(chip); + int shift = offset * 2; + int ret; + + if (!test_and_clear_bit(offset, pdata->gchip_output)) + return 0; + + ret = regmap_update_bits(pdata->regmap, SN_GPIO_CTRL_REG, + SN_GPIO_MUX_MASK << shift, + SN_GPIO_MUX_INPUT << shift); + if (ret) { + set_bit(offset, pdata->gchip_output); + return ret; + } + + /* + * NOTE: if nobody else is powering the device this may fully power + * it off and when it comes back it will have lost all state, but + * that's OK because the default is input and we're now an input. + */ + pm_runtime_put_autosuspend(pdata->dev); + + return 0; +} + +static int ti_sn_bridge_gpio_direction_output(struct gpio_chip *chip, + unsigned int offset, int val) +{ + struct ti_sn65dsi86 *pdata = gpiochip_get_data(chip); + int shift = offset * 2; + int ret; + + if (test_and_set_bit(offset, pdata->gchip_output)) + return 0; + + pm_runtime_get_sync(pdata->dev); + + /* Set value first to avoid glitching */ + ti_sn_bridge_gpio_set(chip, offset, val); + + /* Set direction */ + ret = regmap_update_bits(pdata->regmap, SN_GPIO_CTRL_REG, + SN_GPIO_MUX_MASK << shift, + SN_GPIO_MUX_OUTPUT << shift); + if (ret) { + clear_bit(offset, pdata->gchip_output); + pm_runtime_put_autosuspend(pdata->dev); + } + + return ret; +} + +static int ti_sn_bridge_gpio_request(struct gpio_chip *chip, unsigned int offset) +{ + struct ti_sn65dsi86 *pdata = gpiochip_get_data(chip); + + if (offset == SN_PWM_GPIO_IDX) + return ti_sn_pwm_pin_request(pdata); + + return 0; +} + +static void ti_sn_bridge_gpio_free(struct gpio_chip *chip, unsigned int offset) +{ + struct ti_sn65dsi86 *pdata = gpiochip_get_data(chip); + + /* We won't keep pm_runtime if we're input, so switch there on free */ + ti_sn_bridge_gpio_direction_input(chip, offset); + + if (offset == SN_PWM_GPIO_IDX) + ti_sn_pwm_pin_release(pdata); +} + +static const char * const ti_sn_bridge_gpio_names[SN_NUM_GPIOS] = { + "GPIO1", "GPIO2", "GPIO3", "GPIO4" +}; + +static int ti_sn_gpio_probe(struct auxiliary_device *adev, + const struct auxiliary_device_id *id) +{ + struct ti_sn65dsi86 *pdata = dev_get_drvdata(adev->dev.parent); + int ret; + + /* Only init if someone is going to use us as a GPIO controller */ + if (!of_property_read_bool(pdata->dev->of_node, "gpio-controller")) + return 0; + + pdata->gchip.label = dev_name(pdata->dev); + pdata->gchip.parent = pdata->dev; + pdata->gchip.owner = THIS_MODULE; + pdata->gchip.of_xlate = tn_sn_bridge_of_xlate; + pdata->gchip.of_gpio_n_cells = 2; + pdata->gchip.request = ti_sn_bridge_gpio_request; + pdata->gchip.free = ti_sn_bridge_gpio_free; + pdata->gchip.get_direction = ti_sn_bridge_gpio_get_direction; + pdata->gchip.direction_input = ti_sn_bridge_gpio_direction_input; + pdata->gchip.direction_output = ti_sn_bridge_gpio_direction_output; + pdata->gchip.get = ti_sn_bridge_gpio_get; + pdata->gchip.set = ti_sn_bridge_gpio_set; + pdata->gchip.can_sleep = true; + pdata->gchip.names = ti_sn_bridge_gpio_names; + pdata->gchip.ngpio = SN_NUM_GPIOS; + pdata->gchip.base = -1; + ret = devm_gpiochip_add_data(&adev->dev, &pdata->gchip, pdata); + if (ret) + dev_err(pdata->dev, "can't add gpio chip\n"); + + return ret; +} + +static const struct auxiliary_device_id ti_sn_gpio_id_table[] = { + { .name = "ti_sn65dsi86.gpio", }, + {}, +}; + +MODULE_DEVICE_TABLE(auxiliary, ti_sn_gpio_id_table); + +static struct auxiliary_driver ti_sn_gpio_driver = { + .name = "gpio", + .probe = ti_sn_gpio_probe, + .id_table = ti_sn_gpio_id_table, +}; + +static int __init ti_sn_gpio_register(void) +{ + return auxiliary_driver_register(&ti_sn_gpio_driver); +} + +static void ti_sn_gpio_unregister(void) +{ + auxiliary_driver_unregister(&ti_sn_gpio_driver); +} + +#else + +static inline int ti_sn_gpio_register(void) { return 0; } +static inline void ti_sn_gpio_unregister(void) {} + +#endif + +/* ----------------------------------------------------------------------------- + * Probe & Remove + */ + +static void ti_sn65dsi86_runtime_disable(void *data) +{ + pm_runtime_dont_use_autosuspend(data); + pm_runtime_disable(data); +} + +static int ti_sn65dsi86_parse_regulators(struct ti_sn65dsi86 *pdata) +{ + unsigned int i; + const char * const ti_sn_bridge_supply_names[] = { + "vcca", "vcc", "vccio", "vpll", + }; + + for (i = 0; i < SN_REGULATOR_SUPPLY_NUM; i++) + pdata->supplies[i].supply = ti_sn_bridge_supply_names[i]; + + return devm_regulator_bulk_get(pdata->dev, SN_REGULATOR_SUPPLY_NUM, + pdata->supplies); +} + +static int ti_sn65dsi86_probe(struct i2c_client *client) +{ + struct device *dev = &client->dev; + struct ti_sn65dsi86 *pdata; + int ret; + + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { + DRM_ERROR("device doesn't support I2C\n"); + return -ENODEV; + } + + pdata = devm_kzalloc(dev, sizeof(struct ti_sn65dsi86), GFP_KERNEL); + if (!pdata) + return -ENOMEM; + dev_set_drvdata(dev, pdata); + pdata->dev = dev; + + mutex_init(&pdata->comms_mutex); + + pdata->regmap = devm_regmap_init_i2c(client, + &ti_sn65dsi86_regmap_config); + if (IS_ERR(pdata->regmap)) + return dev_err_probe(dev, PTR_ERR(pdata->regmap), + "regmap i2c init failed\n"); + + pdata->enable_gpio = devm_gpiod_get_optional(dev, "enable", + GPIOD_OUT_LOW); + if (IS_ERR(pdata->enable_gpio)) + return dev_err_probe(dev, PTR_ERR(pdata->enable_gpio), + "failed to get enable gpio from DT\n"); + + ret = ti_sn65dsi86_parse_regulators(pdata); + if (ret) + return dev_err_probe(dev, ret, "failed to parse regulators\n"); + + pdata->refclk = devm_clk_get_optional(dev, "refclk"); + if (IS_ERR(pdata->refclk)) + return dev_err_probe(dev, PTR_ERR(pdata->refclk), + "failed to get reference clock\n"); + + pm_runtime_enable(dev); + pm_runtime_set_autosuspend_delay(pdata->dev, 500); + pm_runtime_use_autosuspend(pdata->dev); + ret = devm_add_action_or_reset(dev, ti_sn65dsi86_runtime_disable, dev); + if (ret) + return ret; + + ti_sn65dsi86_debugfs_init(pdata); + + /* + * Break ourselves up into a collection of aux devices. The only real + * motiviation here is to solve the chicken-and-egg problem of probe + * ordering. The bridge wants the panel to be there when it probes. + * The panel wants its HPD GPIO (provided by sn65dsi86 on some boards) + * when it probes. The panel and maybe backlight might want the DDC + * bus or the pwm_chip. Having sub-devices allows the some sub devices + * to finish probing even if others return -EPROBE_DEFER and gets us + * around the problems. + */ + + if (IS_ENABLED(CONFIG_OF_GPIO)) { + ret = ti_sn65dsi86_add_aux_device(pdata, &pdata->gpio_aux, "gpio"); + if (ret) + return ret; + } + + if (IS_ENABLED(CONFIG_PWM)) { + ret = ti_sn65dsi86_add_aux_device(pdata, &pdata->pwm_aux, "pwm"); + if (ret) + return ret; + } + + /* + * NOTE: At the end of the AUX channel probe we'll add the aux device + * for the bridge. This is because the bridge can't be used until the + * AUX channel is there and this is a very simple solution to the + * dependency problem. + */ + return ti_sn65dsi86_add_aux_device(pdata, &pdata->aux_aux, "aux"); +} + +static struct i2c_device_id ti_sn65dsi86_id[] = { + { "ti,sn65dsi86", 0}, + {}, +}; +MODULE_DEVICE_TABLE(i2c, ti_sn65dsi86_id); + +static const struct of_device_id ti_sn65dsi86_match_table[] = { + {.compatible = "ti,sn65dsi86"}, + {}, +}; +MODULE_DEVICE_TABLE(of, ti_sn65dsi86_match_table); + +static struct i2c_driver ti_sn65dsi86_driver = { + .driver = { + .name = "ti_sn65dsi86", + .of_match_table = ti_sn65dsi86_match_table, + .pm = &ti_sn65dsi86_pm_ops, + }, + .probe = ti_sn65dsi86_probe, + .id_table = ti_sn65dsi86_id, +}; + +static int __init ti_sn65dsi86_init(void) +{ + int ret; + + ret = i2c_add_driver(&ti_sn65dsi86_driver); + if (ret) + return ret; + + ret = ti_sn_gpio_register(); + if (ret) + goto err_main_was_registered; + + ret = ti_sn_pwm_register(); + if (ret) + goto err_gpio_was_registered; + + ret = auxiliary_driver_register(&ti_sn_aux_driver); + if (ret) + goto err_pwm_was_registered; + + ret = auxiliary_driver_register(&ti_sn_bridge_driver); + if (ret) + goto err_aux_was_registered; + + return 0; + +err_aux_was_registered: + auxiliary_driver_unregister(&ti_sn_aux_driver); +err_pwm_was_registered: + ti_sn_pwm_unregister(); +err_gpio_was_registered: + ti_sn_gpio_unregister(); +err_main_was_registered: + i2c_del_driver(&ti_sn65dsi86_driver); + + return ret; +} +module_init(ti_sn65dsi86_init); + +static void __exit ti_sn65dsi86_exit(void) +{ + auxiliary_driver_unregister(&ti_sn_bridge_driver); + auxiliary_driver_unregister(&ti_sn_aux_driver); + ti_sn_pwm_unregister(); + ti_sn_gpio_unregister(); + i2c_del_driver(&ti_sn65dsi86_driver); +} +module_exit(ti_sn65dsi86_exit); + +MODULE_AUTHOR("Sandeep Panda <spanda@codeaurora.org>"); +MODULE_DESCRIPTION("sn65dsi86 DSI to eDP bridge driver"); +MODULE_LICENSE("GPL v2"); |