diff options
Diffstat (limited to 'drivers/gpu/drm/i915/i915_params.c')
-rw-r--r-- | drivers/gpu/drm/i915/i915_params.c | 89 |
1 files changed, 0 insertions, 89 deletions
diff --git a/drivers/gpu/drm/i915/i915_params.c b/drivers/gpu/drm/i915/i915_params.c index 036c4c3ed6..de43048543 100644 --- a/drivers/gpu/drm/i915/i915_params.c +++ b/drivers/gpu/drm/i915/i915_params.c @@ -67,33 +67,9 @@ i915_param_named(modeset, int, 0400, "Use kernel modesetting [KMS] (0=disable, " "1=on, -1=force vga console preference [default])"); -i915_param_named_unsafe(enable_dc, int, 0400, - "Enable power-saving display C-states. " - "(-1=auto [default]; 0=disable; 1=up to DC5; 2=up to DC6; " - "3=up to DC5 with DC3CO; 4=up to DC6 with DC3CO)"); - -i915_param_named_unsafe(enable_fbc, int, 0400, - "Enable frame buffer compression for power savings " - "(default: -1 (use per-chip default))"); - -i915_param_named_unsafe(lvds_channel_mode, int, 0400, - "Specify LVDS channel mode " - "(0=probe BIOS [default], 1=single-channel, 2=dual-channel)"); - -i915_param_named_unsafe(panel_use_ssc, int, 0400, - "Use Spread Spectrum Clock with panels [LVDS/eDP] " - "(default: auto from VBT)"); - -i915_param_named_unsafe(vbt_sdvo_panel_type, int, 0400, - "Override/Ignore selection of SDVO panel mode in the VBT " - "(-2=ignore, -1=auto [default], index in VBT BIOS table)"); - i915_param_named_unsafe(reset, uint, 0400, "Attempt GPU resets (0=disabled, 1=full gpu reset, 2=engine reset [default])"); -i915_param_named_unsafe(vbt_firmware, charp, 0400, - "Load VBT from specified file under /lib/firmware"); - #if IS_ENABLED(CONFIG_DRM_I915_CAPTURE_ERROR) i915_param_named(error_capture, bool, 0400, "Record the GPU state following a hang. " @@ -106,55 +82,10 @@ i915_param_named_unsafe(enable_hangcheck, bool, 0400, "WARNING: Disabling this can cause system wide hangs. " "(default: true)"); -i915_param_named_unsafe(enable_psr, int, 0400, - "Enable PSR " - "(0=disabled, 1=enable up to PSR1, 2=enable up to PSR2) " - "Default: -1 (use per-chip default)"); - -i915_param_named(psr_safest_params, bool, 0400, - "Replace PSR VBT parameters by the safest and not optimal ones. This " - "is helpful to detect if PSR issues are related to bad values set in " - " VBT. (0=use VBT parameters, 1=use safest parameters)"); - -i915_param_named_unsafe(enable_psr2_sel_fetch, bool, 0400, - "Enable PSR2 selective fetch " - "(0=disabled, 1=enabled) " - "Default: 0"); - -i915_param_named_unsafe(enable_sagv, bool, 0600, - "Enable system agent voltage/frequency scaling (SAGV) (default: true)"); - i915_param_named_unsafe(force_probe, charp, 0400, "Force probe options for specified supported devices. " "See CONFIG_DRM_I915_FORCE_PROBE for details."); -i915_param_named_unsafe(disable_power_well, int, 0400, - "Disable display power wells when possible " - "(-1=auto [default], 0=power wells always on, 1=power wells disabled when possible)"); - -i915_param_named_unsafe(enable_ips, int, 0400, "Enable IPS (default: true)"); - -i915_param_named_unsafe(enable_dpt, bool, 0400, - "Enable display page table (DPT) (default: true)"); - -i915_param_named_unsafe(load_detect_test, bool, 0400, - "Force-enable the VGA load detect code for testing (default:false). " - "For developers only."); - -i915_param_named_unsafe(force_reset_modeset_test, bool, 0400, - "Force a modeset during gpu reset for testing (default:false). " - "For developers only."); - -i915_param_named_unsafe(invert_brightness, int, 0400, - "Invert backlight brightness " - "(-1 force normal, 0 machine defaults, 1 force inversion), please " - "report PCI device ID, subsystem vendor and subsystem device ID " - "to dri-devel@lists.freedesktop.org, if your machine needs it. " - "It will then be included in an upcoming module version."); - -i915_param_named(disable_display, bool, 0400, - "Disable display (default: false)"); - i915_param_named(memtest, bool, 0400, "Perform a read/write test of all device memory on module load (default: off)"); @@ -162,19 +93,6 @@ i915_param_named(mmio_debug, int, 0400, "Enable the MMIO debug code for the first N failures (default: off). " "This may negatively affect performance."); -/* Special case writable file */ -i915_param_named(verbose_state_checks, bool, 0600, - "Enable verbose logs (ie. WARN_ON()) in case of unexpected hw state conditions."); - -i915_param_named_unsafe(nuclear_pageflip, bool, 0400, - "Force enable atomic functionality on platforms that don't have full support yet."); - -/* WA to get away with the default setting in VBT for early platforms.Will be removed */ -i915_param_named_unsafe(edp_vswing, int, 0400, - "Ignore/Override vswing pre-emph table selection from VBT " - "(0=use value from vbt [default], 1=low power swing(200mV)," - "2=default swing(400mV))"); - i915_param_named_unsafe(enable_guc, int, 0400, "Enable GuC load for GuC submission and/or HuC load. " "Required functionality can be selected using bitmask values. " @@ -196,18 +114,11 @@ i915_param_named_unsafe(dmc_firmware_path, charp, 0400, i915_param_named_unsafe(gsc_firmware_path, charp, 0400, "GSC firmware path to use instead of the default one"); -i915_param_named_unsafe(enable_dp_mst, bool, 0400, - "Enable multi-stream transport (MST) for new DisplayPort sinks. (default: true)"); - #if IS_ENABLED(CONFIG_DRM_I915_DEBUG) i915_param_named_unsafe(inject_probe_failure, uint, 0400, "Force an error after a number of failure check points (0:disabled (default), N:force failure at the Nth failure check point)"); #endif -i915_param_named(enable_dpcd_backlight, int, 0400, - "Enable support for DPCD backlight control" - "(-1=use per-VBT LFP backlight type setting [default], 0=disabled, 1=enable, 2=force VESA interface, 3=force Intel interface)"); - #if IS_ENABLED(CONFIG_DRM_I915_GVT) i915_param_named(enable_gvt, bool, 0400, "Enable support for Intel GVT-g graphics virtualization host support(default:false)"); |